Over 1 million tech questions and answers.

safe mode and startup error and error messages

Q: safe mode and startup error and error messages

I am having problems with my computer starting in safe mode all the time. I have tried going into msdos and putting in boot 0 and changing read only stuff back again but to no avail.(ie) brindle 10-20-03.. help! I must have changed something some where eh? Also I keep getting these error mess. more and more. I have aim and just recently it started giving me mss about that and if I don't catch the pop up window that comes with aim, in time then my puter freezes on me and I have to shut down and go in again.. Also....... I am still getting the start up mess of a file is missing and to delete and uninstall etc etc then it has Mcaffee system ini etc etc ,...Well I went and deleted all Mcaffee stuff as recomemned by styxx and am still getting this at start up? HELP I am ready to throw this out the window... no pun intended! My husband thinks I have ruined his computer and is still giving me dirty looks..... I have windows 98se. 254 mgbytes memory, I think,and have dsl...Help

RELEVANCY SCORE 200
Preferred Solution: safe mode and startup error and error messages

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: safe mode and startup error and error messages

Have you tried going into set-up and resetting all controls to "default setting"?

You're computer is most likely going into default mode because there is something else wrong with it.

You most likely haven't ruined it........jus need to take this one step at a time

What were the first error messages you were getting?

What happened the first time your computer started in safe mode all by itself?

Read other 1 answers
RELEVANCY SCORE 89.6

>.< I was hoping NEVER to come here again. But I have no other place to go.
Because of this problem: http://www.techsupportforum.com/f10/...ml#post1587221


I love all of your guys work and your helpfulness.



Well the error message is as following


C:\Program files\Windows\system32\(INSERT ANY OF THE FILES BEOW) is not a valid Windows image. Please check this against your diskette


Where it says insert it shows these. But it will show all in multiple messages.


xcikty.dll
aekmjc.dll
kljnin.dll
gijzov.dll
qrvuaz.dll
aozxuf.dll
qfmdtp.dll
ftrkce.dll
xrmqja.dll
rsthsi.dll
cxivwu.dll
tekcvm.dll

They will all pop up in different messages but the error message will stay the same but just use a different one of these.


My question is, Are these real windows files or do they need to be deleted?


-Thanks in advance. Again Thanks for your contribution to the community.

A:Error messages when launching SAFE MODE

Hello Warfare,

Those don't look like normal windows .dll files. Upon searching there are no results found that is a good indication of malware. Do you get the same error messages loading normal mode?

Read other 1 answers
RELEVANCY SCORE 89.6

cant boot in safe mode error messages ati

--------------------------------------------------------------------------------

Hello

When I log into my computer, I get a error message that won't close:

An error has occurred in the script on the page.
line
char
error
code
url
do you want to continue
yes or no

also ther is message saying unable to load language resources please reinstall software WHAT!!!!!
I also can not boot into safe mode
all that comes up is windows/system32/drivers/pcidexsys
but there is about 26 different ones all say the same with the window system32 and drivers but the end is different the last one says mvp/sys

There is nothing posted in the error and when I go to say yes or no nothing happens and it wont close

When I shut down my pc I get another error message saying

HpQtra

I am also having probs with my drivers.

I was told to put my ATI on my desktop and load it from there, but now I get an error message saying
Catalyst Contro Center is not supported by the driver version of your enabled graphics adapter
please update your ati graphics driver or enable your ati adapter using the display manager

I know what this is saying but don't know where to start.

I also have just got the new antivirus prodtection of bitdefender total security 2008

also my activex controls are gone it looks like

very frustrated. I know this is all to do with mostly of my drivers but not sure how to get it off my desktop and back where it belows ... Read more

A:cant boot to safe mode error messages

Read other 9 answers
RELEVANCY SCORE 89.6

Hello.

HP G60 Notebook PC
Pentium Dual-core CPU t4200
3.00 GB RAM
Windows Vista Home Premium 32bit
OEM

For the past week laptop has been displaying message that Windows 6002 build is not genuine. There were also error messages regarding memory and security. On Saturday a friend came over with an external flash drive and copied some Photoshop files. That was the last driver that was installed. The last Windows security update was for Microsoft Office 2007 compatibility which was installed on 11/10/10. Yesterday BSOD appeared:

__________________
A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this stop error screen, restart your computer, If this screen appears again, follow these steps.

Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters.

Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and then select safe mode.

Technical Information
***STOP: 0x0000007e (0xc0000006, 0x8211d0bc, 0xb09cc930, 0xb09cc62c)

Collecting data for crash dump...
initializing disk for crash dump...
beginning dump of physical memory...
dumping physical memory to disk: 100
physi... Read more

A:BSOD, Safe Mode, Error Messages

STOP 0x0000007E: SYSTEM_THREAD_EXCEPTION_NOT_HANDLED Usual causes: Insufficient disk space, Device driver, Video card, BIOS, Breakpoint with no debugger attached, Hardware incompatibility, Faulty system service, Memory, 3rd party remote control,

Usual causes: Insufficient disk space, Device driver, Video card, BIOS, Breakpoint with no debugger attached, Hardware incompatibility, Faulty system service, Memory, 3rd party remote control,




Code:
icrosoft (R) Windows Debugger Version 6.11.0001.404 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.

Loading Dump File [C:\Users\richc46\AppData\Local\Temp\Temp5_Windows_NT6_BSOD_jcgriff2[1].zip\Windows_NT6_BSOD_jcgriff2\Mini111510-02.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows Server 2008/Windows Vista Kernel Version 6002 (Service Pack 2) MP (2 procs) Free x86 compatible
Product: WinNt, suite: TerminalServer SingleUserTS Personal
Built by: 6002.18267.x86fre.vistasp2_gdr.100608-0458
Machine Name:
Kernel base = 0x81e1b000 PsLoadedModuleList = 0x81f32c70
Debug session time: Mon Nov 15 12:59:21.974 2010 (GMT-5)
System Uptime: 0 days 0:09:29.678
Loading Kernel Symbols
...............................................................
................................................................
................................................................
.......... Read more

Read other 8 answers
RELEVANCY SCORE 87.6

Hi, orry if this is what everyone asks in here but would someone be able to look through my minidumps for me? I've been trying to learn how to do it myself but my computer BSODs before I have a chance to get very far.

Starting with the latest (I think):

http://dl.dropbox.com/u/30713/Minidu...1-36114-01.dmp
http://dl.dropbox.com/u/30713/Minidu...1-20592-01.dmp
http://dl.dropbox.com/u/30713/Minidu...1-35755-01.dmp
http://dl.dropbox.com/u/30713/Minidu...1-42463-01.dmp
http://dl.dropbox.com/u/30713/Minidu...1-29655-01.dmp

This has only started within the past few days and has seemed to get progressively worse. I tried running a memory test due to some RAM I installed a while ago and disabled my wireless card as I changed that about six weeks ago. Still crashing even in safe mode, though that just gives me something about how Windows has encountered a critical error and has to shut down in one minute. BSODs include PFN_LIST_CORRUPT, BAD_POOL_HEADER and something about Windows and a critical area (or something) amongst others.

Any clues from the minidumps would be a big help, cheers.

A:Constant BSODs and assorted error messages, even in safe mode.

Please follow the instructions in this post and upload the results here: http://www.techsupportforum.com/foru...ta-452654.html

Read other 3 answers
RELEVANCY SCORE 86.8

please can anyone help me. I am not SUPER computer literate so please be patient with me...lol.

My computer crashed and I am getting various errror codes at different times some of them that I can remember are: 0x0000007, 0x0000007E, 0xoooooo8, and ox049. I am getting the blue screen of death and also get a message something like:
IRLQ_NOT_LESS_OR_EUAL

I can not get on to windows. It goes into a black screen after the windows load up screen with the little green bar..

I can no longer get into safe mode.

I have tried to fix my computer with the recovery disks and it wont fix it. It just does the same thing. Im at total loss of what to do next. Also, I ran the windows diagnostic tool and it told me all was okay...

Any help would be GREATLY appreciated!!!

A:Lot of error messages 0x0000007, oX049, BSOD, cannot get onto windows, no safe mode

upload your the minidump that you got.
Follow the instructions here to enable crash logging: How to Enable a Memory.dmp File Capture Using the Graphical User Interface or the Registry

nex time you get the bsod, upload the minidump.

something with hardware usually causes the irlq error, or drivers. we actually need to read the dump file to see what happened in detail.

Read other 1 answers
RELEVANCY SCORE 84

Hi. I have a Dell system running Windows XP. I am getting a blue screen with a generic error msg (problem has been detected and windows has been shut down to prevent damage). I tried to restart, and picked the option to start in safe mode without networking. It started processing but I get the same blue screen part way through.

I tried putting on of the CD's the came with my system in the drive (Drivers and Utilities CD) but nothing changed. I do have another CD (Operating System) but I didn't want to try it without checking first, as I don;t want to lose the data on my system. Any help appreciated!!!!
 

A:Error msg on startup and can't start in safe mode

Read other 9 answers
RELEVANCY SCORE 82

All signs point to a pretty nasty infection that somehow edited my registry.

As stated, Trying to boot in safe mode gets me the BSOD. Trying to Repair results in a 'Cannot Repair' message. Trying to Restore from a Restore Point gives me a similar error.

When I try to start it normally, I get this error:

"The program can't start because COMCTL32.dll is missing from your computer. Try reinstalling the program to fix this problem."

I do, however, have a laptop and an internal hard drive dock. I've docked it, ran Avast and Malwarebytes and got a few hits, but nothing that helped with the startup problem (After 2 days Avast was STILL searching, as a hard drive connected via USB is pretty freakin' slow), so I ended up ending that one prematurely.

I also ran Windows "Official" Malicious Software Removal Tool, and strangely it automatically restarted my computer about 4 hours in both times I ran it.

Unfortunately, reformatting is strongly undesirable

I tried finding a tool that could rebuild/repair/clean the registry, but it seems most programs do the local registry, not a secondary registry on another drive.

Any help is GREATLY appreciated. Thanks for reading.
 

A:COMCTL32.dll Error on Startup; No Safe Mode, Repair or Restore

Read other 16 answers
RELEVANCY SCORE 82

Hello everyone,
 
I could really use some assistance with a PC problem I'm having (Win 7, 64 bit pro if it matters). I think it is a malware issue after several hours of trying to diagnosis and solve the problem. Anyone's assistance would be GREATLY appreciated. Thank you in advance for your time and consideration. Now onto some specifics and then the problem, details and things I've tried to remedy the issue.
 
I can't get into windows at all, no safe mode (of any kind) only command prompts pretty much.
 
Have I backed up my data? not recently. I would lose quite a bit of information I would like to have.
 
I mentioned malware because after looking around online for hours, it seemed most people having the same issue was caused from malware. Details follow:
 
A few weeks ago on a Friday, I was using my computer as normal (basic web use, social media etc. nothing shady outside of a streaming website for game of thrones). On Saturday I attempted to turn on my pc and I got a black screen with a cursor, but never got the blue welcome screen and the pc restarted. I attempted startup repair several times and the error says startup repair offline. I can't get into safe mode, nothing. I keep getting the black screen with the cursor and then it auto restarts itself. I tried 2 use 2 restore points and then the rest of them got wiped out (not sure why, perhaps the malware). After several frustrating hours of searching online Sat., I turned to a friend who assist... Read more

A:Windows 7 error startup repair offline, can't get into safe mode PLEASE help!

Hello Dirkdangler and welcome to BleepingComputer!             
 
My name is Sirawit and I'm here to help you.
 
Please note that I'm currently in training and my fixes need to be approved first, that may delay our fix a bit, but I will normally reply back in 24 hours.
 
If I don't reply after 3 days, feel free to PM me.              
==========================================================================Some points for you to keep in mind:
Backup any files that cannot be replaced. Removing malware can be unpredictable and this step can save a lot of heartaches if things don't go as planned. You can put them on a CD/DVD, external drive or a pen drive, anywhere except on the computer.
We ask you to run different tools in a specific order to ensure the malware is completely removed from your machine, and running any additional tools may detect false positives, interfere with our tools, or cause unforeseen damage or system instability.
Please do not run any tools or take any steps other than those I will provide for you while we work on your computer together. I need to be certain about the state of your computer in order to provide appropriate and effective steps for you to take. Most often "well intentioned" (and usually panic driven!) independent efforts can make things much worse for both of us. If at a... Read more

Read other 4 answers
RELEVANCY SCORE 82

Hello everyone, I could really use some assistance with a PC problem I'm having (Win 7, 64 bit pro if it matters). I think it is a malware issue after several hours of trying to diagnosis and solve the problem. Friday, I was using my computer as normal (basic web use, social media etc.). Saturday I attempted to turn on my pc and I got a black screen with a cursor, but never got the blue welcome screen and the pc restarted. I attempted startup repair several times and the error says startup repair offline. I can't get into safe mode, nothing. I keep getting the black screen with the cursor and then it auto restarts itself. I tried 2 use 2 restore points and then the rest of them got wiped out (not sure why, perhaps the malware). After several frustrating hours of searching online Sat., I turned to a friend who assisted me today for about 5 hours. He found an old thread on this forum for what seems to be a similar problem. He took me through the steps. Here is the thread: http://www.bleepingcomputer.com/forums/t/448339/windows-failed-to-start-system-repair-cant-discover-problem/ We followed JSntgRvr's instructions and in his 2nd response in the thread, we got all the way to the step before this: "Boot in Normal Mode. If able to do so, please run Combofix as follows:" We couldn't get my desktop to boot in normal mode, so could go no further. Below, I'll post the list of the report. Before that, I will say any assistance is GREATLY appreciated. Also, when... Read more

A:Windows 7 error startup repair offline, can't get into safe mode PLEASE help!

Can you get into Windows at all?
Have you backed up your data?
You mentioned malware - why do you think the system is infected?
 
We can help here with some things, but if it's malware we're not equipped to deal with that here.
If infected, I'd suggest posting over in the Am I Infected forum:  http://www.bleepingcomputer.com/forums/f/103/am-i-infected-what-do-i-do/
Please read the pinned topics at the top of the forum for instructions on how to post there.
 

Read other 3 answers
RELEVANCY SCORE 82

When I try to boot my computer, a blue screen pops up saying fatal system error and windows logon terminated and the system is shutting down. I've tried to boot up in safe mode and it wont even let me do that. The same screen pops up and keeps restarting the computer.

A:Fatal System Error on startup, cant even boot in safe mode

If this is the same computer that you are talking about here:http://www.bleepingcomputer.com/forums/ind...amp;pid=1304088You need to reformat and reinstall

Read other 1 answers
RELEVANCY SCORE 81.2

I've looked through the forums and didn't see anything about my specific issue(s). Apologies if I've overlooked a thread already posted.
 
My issue: My daughter has an emachine with Windows 7 OS. It's been closing webpages while she's on them, so I ran a virus scan. We had AVG and it didn't pick up anything.
Now it flashes a blue screen (too quickly for me to see what messages are displayed), then acts as if it's going to start up. However, it brings up an error message that there is a startup error.
I get an option to start in repair mode or normal mode. I've tried both - normal mode repeats this display. Repair mode runs for a minute, then states that it cannot repair the issue. It takes me to the tools screen and offers the options for Repair, System Restore, Memory Diagnostic, etc. I've run the diagnostics, I've run the chkdsk, all of that. I did several system restores but got a message that system restore didn't restore.
 
Sometimes it will let me into windows (after attempting to restore several times), but if I have to restart it, it starts all over again.
 
Yesterday I used this computer to burn a copy of Sophos Virus Tool Scanner. I popped the disk in and started it up, and it loaded Windows (followed by a message that system restore was complete. ?) I ran the scanner, found several Malwares and a Troj/Agent.ADIL virus. It removed the Malware but not the Trojan. I went to malwarebytes and downloaded it, and it removed a bunch of stuff. ... Read more

A:BSOD flashes, startup error, won't boot or load in safe mode

Hi Burlesquemoon and welcome to BC.  To help us help you please run the following. Thank you.
 
Please download MiniToolBox  , save it to your desktop and run it. Checkmark the following checkboxes:  List last 10 Event Viewer log  List Installed Programs  List Users, Partitions and Memory size. Click Go and paste the content into your next post.

Read other 4 answers
RELEVANCY SCORE 81.2

I've been having a problem for a while now when restarting my desktop
computer. When restarting, I am getting a blue screen, "a problem has been detected and winudows has been shut down to prevent damage"
Technical Information:
Stop: 0x0000007b (0xF890D528, 0xC0000034, 0x00000000, 0x00000000)

I've been getting that message for a while now and every now and then it I wouldn't get that message and the computer boots fine. But now, I'm getting that every time.

Previously, when getting this message, I have been able to boot into safe mode. Now, I can't even get through safe mode as it hangs when trying to load Agp440.sys.

So, I'm stuck with this problem unable to figure out how to fix it. Any suggestions would be great. thanks.

A:Blue Screen error on startup & unable to boot safe mode

check you ide cable is secure at the drive and the m/board
try a new cable
boot into the recovery console and run
chkdsk /r

Read other 5 answers
RELEVANCY SCORE 76.8

Hi,My Computer which has Win Xp Sp3 is behaving like it is in safe mode , eventhough it is in normal mode .I noticed this because ,1. Avira Antivir Guard and Update cannot be launched bcz Scheduler is not running.2 . I tried to start scheduler ( under services.msc ) , but can't start it bcz of error 1084 ( safe mode situation ) .3 . I can't use Windows Update , bcz of error Error number: 0x8007043C ( same safe mode condition )4 . I ensured that BITS was set to automatic , but it can't run bcz of 1084 error.I have scanned with Malwarebytes, Spybot S&D , SuperAnti Spyware ( in real safe mode) - No DetectionHere is the dds log ,DDS (Ver_09-09-24.01) - NTFSx86 NETWORK Run by Administrator at 16:45:23.03 on Mon 09/28/2009Internet Explorer: 8.0.6001.18702 BrowserJavaVersion: 1.6.0_12Microsoft Windows XP Professional 5.1.2600.3.1252.1.1033.18.510.112 [GMT 5.5:30]AV: ZoneAlarm Security Suite Antivirus *On-access scanning disabled* (Outdated) {5D467B10-818C-4CAB-9FF7-6893B5B8F3CF}AV: AntiVir Desktop *On-access scanning enabled* (Outdated) {AD166499-45F9-482A-A743-FDD3350758C7}FW: ZoneAlarm Security Suite Firewall *enabled* {829BDA32-94B3-44F4-8446-F8FCFF809F8B}============== Running Processes ===============C:\WINDOWS\system32\svchost -k DcomLaunchsvchost.exeC:\WINDOWS\system32\svchost.exe -k netsvcsC:\WINDOWS\system32\ZoneLabs\vsmon.exeC:\WINDOWS\Explorer.EXEC:\Program Files\Avira\AntiVir Desktop�... Read more

A:Safe Mode Error, WinXpSp3 behaves like it is in safe mode even in normal mode

Hello and welcome to Bleeping ComputerWe apologize for the delay in responding to your request for help. Here at Bleeping Computer we get overwhelmed at times, and we are trying our best to keep up. Please note that your topic was not intentionally overlooked. Our mission is to help everyone in need, but sometimes it takes just a little longer to get to every request for help. No one is ignored here.If you have since resolved the original problem you were having, we would appreciate you letting us know. If not please perform the following steps below so we can have a look at the current condition of your machine. If you have not done so, include a clear description of the problems you're having, along with any steps you may have performed so far.Upon completing the steps below another staff member will review and take the steps necessary with you to get your machine back in working order clean and free of malware.If you have already posted a DDS log, please do so again, as your situation may have changed.Use the 'Add Reply' and add the new log to this thread.Thanks and again sorry for the delay.We need to see some information about what is happening in your machine. Please perform the following scan:Download DDS by sUBs from one of the following links. Save it to your desktop.DDS.scrDDS.pifDouble click on the DDS icon, allow it to run.A small box will open, with an explaination about the tool. No input is needed, the scan is running.Notepad will open with the results.Foll... Read more

Read other 2 answers
RELEVANCY SCORE 74.8

Hello,

I've been having this nasty problem since yesterday. I have no knowledge of viruses whatsoever so I am at a complete loss as to what to do.

I'm using a 7-year-old laptop and Windows XP. At a guess, the problem comes from my friend's USB. This is what happened: I inserted the USB and noticed a RECYCLER and some Shorcut to (1) etc. viruses. I thought this wasn't serious so I ignored it. An hour or two after that my Internet connection crashed (I don't know if it has anything to do with the virus). By checking randomly, I found out that gpedit.msc and my Antivir setup file also refused to run.

I then shut down my computer and have been unable to boot ever since. Every time I try to start up, I am faced with a dozen of "out of memory" pop-ups, all of them with "xxx" in their title bar. I tried closing them all, but new ones kept springing up. I opened Task Manager and found at least 20 processes named FONTS.EXE. I guess this was what caused the "out of memory" error, so I tried to end those processes, but they kept re-appearing over and over again.

The taskbar and the desktop icons won't show up. The screen is blank - there's just my wallpaper background, my cursor and the nasty error pop-ups. I can't run any virus check or do anything else.

I've also tried rebooting in Safe Mode, but it took me to the blue screen of death.

Another problem, my laptop's CD driver is out of order (as I said... Read more

Read other answers
RELEVANCY SCORE 70

I have been getting BSOD errors whenever booting into regular mode. Safe mode is fine (I have tweaked the registry so I have sound in safe mode) My system specs are in my profile, but used Winaudit for full specs. The winaudit report in formatted text is too big for an attachment. I have 2 attachments to this post, including zipped up minidumps.
Could my registry tweak for sound have something to do with this?
Perfmon /report was run, but it says:


An error occured while attempting to generate the report.



The system cannot find the path specified.

A:BSOD booting into full mode, safe mode works stop error 0x0000003b

  
Quote: Originally Posted by nrabus


I have been getting BSOD errors whenever booting into regular mode. Safe mode is fine (I have tweaked the registry so I have sound in safe mode) My system specs are in my profile, but used Winaudit for full specs. The winaudit report in formatted text is too big for an attachment. I have 2 attachments to this post, including zipped up minidumps.
Could my registry tweak for sound have something to do with this?
Perfmon /report was run, but it says:


An error occured while attempting to generate the report.



The system cannot find the path specified.


You have several issues. It might be easier to simply clean install.

You choice, here are the most obvious problems

Avg

Kaspersky

Pctools

Symantec

One or all of the above are causing an issue with tcpip.sys which need to be fixed.
If you decide you want to remove instead of clean install we have the removal tools inks.

Read other 6 answers
RELEVANCY SCORE 69.6

Just purchased a new HP 8560 Elitebook with Win 7 professional 64 bit. Upon startup I get three messages:
Resource file<C_SpURs Dll>
Resource File<C_PsdRs Dll>
PSDrt

Where can I go to find a fix for these error messages that pop up and what do they pertain to?? Thanks

A:error messages on startup

Hi have you used a reg cleaner,the other thing it may be is HP Embedded Security for or Infineon TPM which you can remove from programs and features add\remove programs

Read other 2 answers
RELEVANCY SCORE 69.6

For the past week or so, I have been getting an error message at startup along the lines of "Windows cannot find the file or folder "copy" etc... I can't get the exact text because it doesnt happen all the time, and nothing seems to actually go wrong other than the message. I've checked all my windows updates and whatnot, and I don't mess around with my system files much, certainly not since this has started. Any ideas?
 

A:Error messages on startup

we will need the exact message...
 

Read other 2 answers
RELEVANCY SCORE 69.6

upon startup an error message comes up that says......cannot find system32\scvhost.exe........approximately 4 of these appear, what is wrong with either my startup or registry for these to come up?

A:startup error messages

svchost.exe is a legitimate system file and should be left alone. scvhost.exe is a virus or malware program.
Try running an anti virus program and a spy program such as Ad-aware.

Read other 5 answers
RELEVANCY SCORE 69.6

Hay guys Im new here as you may well tell.. But I was woundering if you could help me please?

Im running Windows XP on a P4 IBM system and evey time I restart the PC I get 9 messagers that pop up one after the other and I was woundering would you happen to know how I might beable to fix the problem? or run me though how to fix it.

the errors are as follows.
 

A:Error Messages after Startup of XP

Read other 13 answers
RELEVANCY SCORE 69.6

Hi there,

Just went through a full system malware removal and security update via the Malware/HJT forum. Since then however, I have been receiving two error messages when Windows starts up (XP). I will try to paste the screenshots of the msgs below, but I dont think it will work, so I will also type the details of the errors.


Error #1

"AirGCFG.exe - Entry Point Not Found

The procedure entry point apsSearchInterface could not be located in the dynamic link library wlanapi.dll."

Error # 2

"WZCSLDR2.exe - Entry Point Not Found

The procedure entry point apsInitialize could not be located in the dynamic link library wlanapi.dll."

Both errors show up with a red circle and white 'X'. I suspect that this dll file is missing, but not sure how important it is. Any suggestions for correcting the problem?

Thanks,

T
 

A:Error messages upon startup

Better go back to Security Forum as this is most likely a Vundo infection. The second one is for sure and the first one is either a driver issue on a Dlink wireless card or another Vundo example.
 

Read other 2 answers
RELEVANCY SCORE 69.6

i am working on an hp omnibook xe3 gf running windows 2000. connected to it is a hp350cb1 printer using the infrared port. tihs configuration works perfectly with no exclamation marks in device manager or errors in event viewer.
the problem starts when i install a nokia 6210 connected via cable (not infrared) i get an error in device manager - ir bridge kernal-level interface has an exclamation mark on it after a reboot (i have to reboot after the nokia installation) i also get an error message appear on screen after login - usrbridg.exe has generated errors and will be closed by windows.
windows 2000 has service pack 2 installed.
even though i'm getting this error, the printer still prints via the infrared port!
i've ran the win2k restore disk supplied with the notebook and also built w2k off an original microsoft w2k pro release (installing the drivers for all devices manually)which both worked with no errors until installing the nokia!
i've even tried installing the nokia via the infrared port and not the cable, and got exactly the same error messages.
i've tried removing the devices and reinstalling to the same errors. i've also tried a different phone(same model) still the same error message!
help!
 

A:error messages on startup

Read other 7 answers
RELEVANCY SCORE 69.6

Upon start up before opening anything I get two error messages

1st vb Accelerator S Grid ll Cont
Run Time error "0"

2nd Malwarebytes' Anti-Malw....
Run-Time error '440'
Automation error

below each error message is an OK box which I have been checking off so I can continue.
Are these messages serious enough to do something about? Computer is running good
Have done a defrag and ran system clean up. Run Stop Sign every day for bad "stuff"
 

A:XP error messages on startup

There seems to be a fix posted at the Malwarebytes' forum here:
READ the whole thread, and then probably best to use the clean install method, or try the fix.

http://forums.malwarebytes.org/index.php?showtopic=78114

Not sure if that will take care of the other error or not but it may.
 

Read other 2 answers
RELEVANCY SCORE 69.6

When I turn my computer on, I get the following error message before the xp operating system boots..."Invalid good diskette..Insert boot diskette in A:"

The floppy drive and the CD Drive are empty when I get this error message....the only way I can get past this is to hit Control /Alt /Delete..Then the system will boot into XP (although very slowly)...What is the problem here, and how can I get it fixed?
 

A:startup error messages

Sounds like your floppy drive died. Try going into bios and where the floppy option is, change the a drive to "not installed" then save and reboot. That should prevent the message until you can replace the drive (usually $10).
 

Read other 1 answers
RELEVANCY SCORE 69.6

Whenever my pc restarts I get these error messages:
 
SVPWUTIL
Get supervisor password status function fail!!!
 Supervisor Password Utility
registered
User password mode
able to run hwsetup   
 
(I have never registered a supervisor password)
 
Microsoft Visual C++ Runtime Library
This application has requested the runtime to terminate in an unusual way.
Please contact the applications support team for more information.
 
Is there anyone that can help me resolve these issues? Thank you in advance!

A:Error messages on startup.

Please post system specs it helps the guys.

Read other 9 answers
RELEVANCY SCORE 69.6

Hello,

I recently had a virus that masqueraded as a legitimate anti-virus program (I think it was System Security). After a long process of going into safe mode and uninstalling it, I ran Malwarebytes and cleaned up the rest of the infections on my computer. However, after the login screen comes up, an error saying this pops up:

Windows cannot copy file C:\Documents and Settings\patron.orig\Local Settings\Temporary Internet Files\Content.IE5\0EJGS7S6\.biz_M-cm.nfl_M-cm.EX_hisp-cm.music_M;;tile=1;ord1=4092;sz=728x90;contx=none;btg=cm.biz1;btg=cm.biz_M;btg=cm.nfl_M;btg=cm.EX_hisp;btg=cm[1].music_M;ord=[timestamp] to location C:\Documents and Settings\patron\Local Settings\Temporary Internet Files\Content.IE5\0EJGS7S6\.biz_M-cm.nfl_M-cm.EX_hisp-cm.music_M;;tile=1;ord1=4092;sz=728x90;contx=none;btg=cm.biz1;btg=cm.biz_M;btg=cm.nfl_M;btg=cm.EX_hisp;btg=cm[1].music_M;ord=[timestamp].

DETAIL - The filename or extension is too long.

Possible causes of this error include network problems or insufficient security rights. If this problem persists, contact your network administrator.

Then the next screen says something to the effect that the computer couldn't log on to the user that was specified but was able to log onto the default profile instead. This is a problem because the computer that is infected is at the library I work at and we don't want people to mess with settings that they can now access us... Read more

A:Startup Error Messages

Moved from XP to a more appropriate forum. Tw

Read other 11 answers
RELEVANCY SCORE 69.6

I recently installed a new CPU. Ever since then during startup I have gotten the below error messages. I also am having trouble with Media Player crashing during startup and/or playback.

I have-
MB: ASUS p5KE
Processor: Intel Core 2 Duo E8400 (adding this caused the problems?)

Error Messages:
DIGITAL CABLE DEVICE REGISTRATION APPLICATION. STOPPED WORKING AND WAS CLOSED: A problem caused the application to stop working correctly. Windows will notify you if a solution is available.

WINDOWS MEDIA PLAYER NETWORK SHARING SERVICE STOPPED WORKING AND WAS CLOSED: A problem caused the application to stop working correctly. Windows will notify you if a solution is available.

What's the fix?

Read other answers
RELEVANCY SCORE 69.6

I recently ran AVG Free 8.0 to remove a Trojan Horse virus. Snce then, I receive the following two error messages:

C:\Windows\inalubemojok.dll
The specified module could not be found.

C:\Windows\lnoxe.dll
The specified module could not be found.

I click ignore and continue. Operation appears normal.
I have searched Microsoft and various online dll archives and can find no reference to the dll modules/files mentioned.
Any comments appreciated and how can I remove the error messages?
Kurt
[email protected]

Read other answers
RELEVANCY SCORE 69.6

Hello
Everytime I switch on my computer I get the two following messages:

THIS APPLICATION HAS FAILED TO START BECAUSE CCL40.DLL WAS NOT FOUND

and
THE PROCEDURE ENTRY POINT GETPROCESSIMAGEFILENAMEW COULD NOT BE LOCATED IN THE DYNAMIC LINK LIBRARY PSAPI.DLL.

Once i click ok on both of these messages my machine runs fine. I would just like to know what could be done to sort out these messages.

thanks

A:Error Messages On Startup

Possibly missing a Norton AV file: See here for more information: http://www.programchecker.com/file/19067.aspx

Read other 1 answers
RELEVANCY SCORE 69.2

Hello,

Recently my dad's computer had a corrupted hive and boot.ini. Via this website, I was instructed to run a chkdsk /r while in the recovery console. Everytime I used his OS disk to get into the recovery console, it prompted me for a password and I didn't know it (nor could I leave it blank). I decided to use my OS disk from my computer and I could fix the problem. Now, though, everytime I startup the computer, it prompts me to start windows normally, in safe mode, in safe mode with networking... To give further information...on that same screen there is an option for Windows XP and Windows XP Home Edition. Don't know if that has something to do with it. They both work though when I press enter on either one. Could anyone help me stop the computer from prompting me??? Thank you for any help.

Read other answers
RELEVANCY SCORE 68.8

A few days ago when starting up my computer my computer prompted me to do a startup repair, which I did. When I restarted my computer I got some error messages once Windows started, such as:
"C:\Windows|Microsoft.Net\Framework\v4.0.30319\mscoreei.dll could not be loaded."
I got another error message when I opened Google Chrome, but was able to get it to work when I reloaded the page.

I tried a system restore to the last restore point (about 10 days ago).
Ever since then, when I start up Windows, I get a series of error messages for application errors and initialization errors for basically every program on my system, and I can't open most programs. Some of the errors:
"The application failed to initialize properly. (0x0000096). Click OK to terminate the application."
"iTunes Helper was not installed correctly. Please reinstall iTunes."

Any ideas what might have caused this problem, and how it can be fixed? Will I have to reinstall Windows Vista? I have tried to research this but haven't found any answers for this exact problem.
Thanks for any ideas you might have!

A:Error messages for every program at startup

It could be a failing hard drive so immediately back up all your data, (not forgetting bookmarks, emails etc), then test the drive with the drive maker's diagnostic software.
It's available in both Windows or DOS (bootable CD) versions, so if your Windows is already problematic you may have to use the DOS version. The links are here:
Hard Drive Diagnostics Tools and Utilities (Storage) - TACKtech Corp.

Read other 1 answers
RELEVANCY SCORE 68.8

I have XP pro. When booting up, while Spyware Stormer is starting up, my computer gets a series of three pop-up error messages, to wit: "Symantec CCApp, A necessary component of this function is missing or damages (\NAVAPW32.DLL)", or the same messages but these different names "(\DEFALERT.DLL)" and "(\ccimscan.dll)". I have previously removed all Symantec programs -- or thought I did.

As far as I can tell, I am having zero problem with my computer or any of the programs. Still, these 3 error messages are irritating. Can you tell me how to get rid of them?
 

A:Irritating pop-up error messages during startup

You didn't get it cleanly removed

http://service1.symantec.com/support/nav.nsf/docid/2001092114452606
 

Read other 1 answers
RELEVANCY SCORE 68.8

I downloaded some mouse related softwares recently that tell you date etc.. they slowed down my mouse so much that I had to delete them completely.
In the process I seem to have deleted some dll or other important files. Now I have a number of problems
1) slow startup - many error messages like "dxtrans.dll cannot be found", .ocx file not found in system32 etc.. show up at startup.
2) One other error message is: RpcSs.exe - The procedure entry point RtlRegisterSecureMemoryCacheCallback could not be locatedi nthe dynamic link library ntdll.dll
3)Service Control Manager - atleast one service or driver failed during start up. Use event viewer to examine event log for details.

4) Another annoying problem is Control C and Control V donot work for cutting/pasting. Further, I cannot access many webpages and get messages like "Error Found in page", "Change settings" etc. I reinstalled IE6.0 but nothing changed.

I have WINDOWS NT 4.0 with IE6.0 and Netscape 6.0 browser

Thanks in advance to all who can help me out.
Cel
 

A:[Resolved] Error messages at startup

Read other 16 answers
RELEVANCY SCORE 68.8

Hi,

I know y'all are uber-busy with virus and spyware removal. My PC seems to be taking several minutes to start-up and I just need someone to see if there is anything I can remove to make it come up faster.

One thing I can see is software running for my DLink Wireless card. I have the card and wireless connection disabled as I have this PC direct connected to my router.

Logfile of Trend Micro HijackThis v2.0.2
Scan saved at 5:44:36 PM, on 2/20/2009
Platform: Windows XP SP3 (WinNT 5.01.2600)
MSIE: Internet Explorer v7.00 (7.00.6000.16791)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\D-Link\AirPlus Xtreme G\AirPlusCFG.exe
C:\Program Files\Alpha Networks\ANIWZCS Service\WZCSLDR.exe
C:\Program Files\iTunes\iTunesHelper.exe
C:\Program Files\McAfee.com\Agent\mcagent.exe
C:\Program Files\Common Files\Pure Networks Shared\Platform\nmctxth.exe
C:\WINDOWS\RTHDCPL.EXE
C:\Program Files\Common Files\Real\Update_OB\realsched.exe
C:\Program Files\Microsoft IntelliPoint\ipoint.exe
C:\Program Files\Microsoft IntelliPoint\dpupdchk.exe
C:\Program Files\Common Files\Apple\Mobile Device Support\bin\AppleMobileDeviceService.exe
C:\Program Files\Bonjour\mDNSResponder.exe
C:\Program Files\Diskeeper Corporation\Diskeeper\DkService.exe
C:\Pr... Read more

Read other answers
RELEVANCY SCORE 68.8

Hi, forgive me if this is the wrong place to be posting this particular topic but I'm brand new here and I understand the need for searching prior to posting, which I did with zero results found. So...

I get the following four messages on start-up, after Windows (XP) has loaded:

"The system cannot find the file specified - Creatfile"
"The handle is invalid - IOCTL_SIS_LIB_WRITE_PORT_ULONG"
"The handle is invalid - IOCTL_SIS_LIB_READ_PORT_ULONG" and
"The requested control is not valid for this service - ControlService"

They've been there for many months now and don't appear to cause any issues - I just click the "OK" associated with each error message and everything carries on as normal. I just finally got around to wondering if/how I could get rid of them.

Many thanks,

Kim

PS this is just one of many "issues" my PC has - but as that Sound Of Music lady once said, let's start at the very beginning

A:[SOLVED] Error messages on startup

Read this:

http://www.bleepingcomputer.com/forums/topic161636.html

See if there are any commonalities between your problems and this one.

Most of the Google hits on one of your error texts come back in French. Any reason that you can think of, for this ?

Read other 15 answers
RELEVANCY SCORE 68.8

please help me out here. whenever i start my laptop, i get 2 messages. i know this is not normal so please help me to remove these messages

this is the 1st one



and this window was behind the 1st one (the one shown above)

A:Windows startup error messages

It looks like something is trying to be opened and it is asking you what program you want to use.

Personally, I would go into run>msconfig>services> tick hide all microsoft services, then check ONLY the programs you want to run at startup. Which should only be your anti-virus, Malwarebytes, gadgets if you use them and that`s it. Click apply, ok, then restart the pc. See if the problem persists. Let us know.

http://www.windowsanswers.net/articl...FROe4AodoTYAcA

Read other 2 answers
RELEVANCY SCORE 68.8

I havent found any solutions yet on any other posts. This problem came up after a serious infection i used avast free antivirus to remove the problems and i think it may have deleted some important dll's or those linked to the virus im not too sure. I've reinstalled other dll's but these do not ask me to do so. The error message's are:

Error loading C:\WINDOWS\mpcape.dll

The specified module could not be found.

and

Error loading C:\WINDOWS\obecusur.dll

The specified module could not be found.

Ive done a HJT scan and saved the log but have no idea what to do with it as this is where my computing skills end. Also i am unable to connect to the internet ever since this and i have no clue what to do. Any help would be much appreciated
 

Read other answers
RELEVANCY SCORE 68.8

I am running Windows XP Pro SP3

When starting my computer I am getting 3 messages that state:
1) Error loading C:\windows\system32\figebasi.dll
2) Error loading C:\windows\system32\jugodika.dll
3) Error loading C:\windows\system32\nusuzefia.dll

When I click through the OK on the error message Windows goes ahead and loads and I don't really notice anything wrong but I would like to get these error messages repaired.

I have Norton antivirus, Ccleaner, AdAware and Malwarebytes that I update and run regularly.

Curious if anyone has any idea what may cause this. This is my first post and if this should go in a different location please let me know and I will move it. Thank you for any help and/or info with this problem.

A:Error loading dll messages at startup

anti-malware softwares sometime remove a nasty but leaving behind entries in registry that still try to load dll's linked to the removed nasty.

it could also be caused by (noob) users manually deleting a program without using the proper uninstall procedure.

try using registry repair tools, like glary registry repair, and see if it cleans those entries out.

Read other 1 answers
RELEVANCY SCORE 68.8

I have a Dell Studio 1555 laptop running Vista Home Premium.

When I switch on the laptop, I get the Dell screen, followed by the Windows logo: so far so good. My laptop is password protected, so the next thing I get is a screen asking for my password. Again, so far so good. Now, when I key in my password and hit enter, I would usually get a screen saying 'Welcome' and then a little later my desktop.

What's been happening lately is that I only get the desktop background (although occasionally I see my desktop icons); I also see the taskbar (though it's completely unresponsive, including the Windows logo button). Then I get a series of error messages, as follows. The text before the colon is the text on the tab; the text after the colon, in inverted commas, is the error message itself.

(Apple system notification something something):

"the application failed to initialize properly (0xc0000006). Click OK to terminate the application."

DellVideoChat.exe-bad Image:
"C:\Windows\WinSxS\x86_microsoft.vc90.crt_1fc89a1e18e3b_9.0.21022.8_none_bcb86ed6ac711f91\MCVCP90.dll is either not designed to run on Windows or it contains an error. Try installing the program again using the original installation media or contact your system administrator or the software vendor for support."

PDVDDXSrv.exe – Bad Image:
"C:\Windows\system32\DCIMAN32.dll is either not designed to run on Windows or it contains an error. Try installing the program again... Read more

A:Error messages and unresponsiveness upon startup

Read other 8 answers
RELEVANCY SCORE 68.8

I'm really, really frustrated. Pull up a chair, and let me tell you my story.

For a while now, I've been getting registry error messages every time I boot up my computer and Windows starts up. As soon as my desktop has loaded, I have to close about six little boxes that tell me " **file cannot be found. Please type file name in correctly, or remove from registry." After I close these windows, everything is ok.

Long story short, I have downloaded a few games from a pay game site I belong to, and the computer seems to be a little sluggish. (but the startup error messages were present before the game downloads). Anyway, last night I hit Google to try and find a reg repair tool that was either freeware or shareware. On PCnet.com, I found a product called RegCure™, that appeared to be the answer to all my problems. I scanned my system, and was told there were 815 registry problems present. Needless to say, if you wanted all of them repaired, you needed to pay 30 bucks to register the program. I'm thinking well, this will be a useful little utility, and thirty bucks isn't that much to get rid of all these problems, so I bit the bullet and bought it. I went through paypal, and minutes laterI was all set to run the program and repair the registry, which I did.

This morning I booted up my system for the first time since the "cleansing." When Windows finished loading, lo and behold, guess who was still around? My little friends, the registry ... Read more

A:Solved: Error Messages at Startup

Read other 7 answers
RELEVANCY SCORE 68.8

Upon startup I get the following error messages:

No ISDN devices were found. Please install an ISDN device and run connection wizard.

Also, cannot find file C:\\windows\system\mgst_tq.ini

The machine had the Mgstr virus and I ran Norton and then deleted the corrupted files. Now I get these messages. I have run the internet connection wizard and it says it set it up properly but still get this message upon start up.

This is not my machine but our church's machine that I am trying to help with.

Any suggestions?
 

A:[Resolved] error messages upon startup

Read other 8 answers
RELEVANCY SCORE 68.8

I'm an admitted newbie and would really appreciate it if anyone could provide some insight on the following:

Running a fresh install of Win XP Home w/ SP1 on an Asus A8V. Sometimes when Win starts I get the following three error messages in the following order:
"The Service Data Base is Locked"
"Can't Start Kernel Mode Driver Service"
"Unrecognized video card"

I only receive these messages intermittently and there doesn't seem to be any rhyme or reason to what causes them (e.g. there's no correlation between getting the error messages and whether the machine has been sitting cold of running for hours and then restarted).

I haven't noticed any problems with the system as everything seems to be running just fine. No lockups, just these weird error messages when I boot.

I'm going to update the BIOS to the MOBO, but does anyone out there have any clues about what's causing these error messages? I'd be more than happy to provide more info if necessary. Thanks in advance!

A:Random Startup Error Messages

Well:

For:
"The Service Data Base is Locked"

See:
http://www.jsiinc.com/SUBC/tip1000/rh1081.htm

I'm not to sure about the other ones yet. How often do you get these? every time you reboot? every other reboot? every few hours? every day?

Can you think of anything else weird that happens?
When did this start?

Download Hijack this:
http://www.download.com/HijackThis/3...ml?tag=lst-0-4

Run that, and then post the log here.
Have you already tried an updated virus scan, and a spyware scan?

Read other 2 answers
RELEVANCY SCORE 68.8

Hello, I'm new to this site and my friend recommended it. I'm having problems with my computer. I keep getting 3 error messages after I start up. Generic Host Process for Wind32 Services from Microsoft, Security Alert from Symantec and svchost.exe - Application Error. I downloaded Hijack this and did the log thing. Can anybody help me?

Love Always,
Carrie
Logfile of HijackThis v1.99.1
Scan saved at 12:08:54 PM, on 3/19/2007
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP2 (6.00.2900.2180)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\LEXBCES.EXE
C:\WINDOWS\system32\LEXPPS.EXE
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\Symantec\LiveUpdate\ALUSchedulerSvc.exe
C:\Program Files\Common Files\Symantec Shared\ccProxy.exe
C:\Program Files\Common Files\Symantec Shared\ccSetMgr.exe
C:\Program Files\Common Files\Microsoft Shared\VS7DEBUG\MDM.EXE
C:\Program Files\Microsoft SQL Server\MSSQL$MICROSOFTBCM\Binn\sqlservr.exe
C:\WINDOWS\System32\DSentry.exe
C:\WINDOWS\system32\dla\tfswctrl.exe
C:\Program Files\Common Files\Symantec Shared\ccApp.exe
C:\PROGRA~1\Maxtor\OneTouch\Utils\OneTouch.exe
C:\WINDOWS\MXOALDR.EXE
C:\WINDOWS\system32\hkcmd.exe
C:\WINDOWS\system32\igfxpers.exe
C:\Program Files\Norton Internet Security\Norton AntiVirus\navapsv... Read more

A:Solved: 3 Error messages at startup

Read other 9 answers
RELEVANCY SCORE 68.8

My cousin's computer was infected with the "Security Defender" virus. I followed BleepingComputer's steps here http://www.bleepingcomputer.com/virus-removal/remove-security-defender to remove it. MalwareBytes' removed it just fine.After MalwareBytes removed the infected files, I allowed it to restart the computer to complete the removal process. After restarting the computer, I have now began receiving two RUNDLL error messages at startup. After Windows loads, I am presented with these two RUNDLL messages below:They are both the same RUNDLL messages, but the part I covered up is my cousin's name. One of the messages shows it's under the "All Users" account, and the other message (the one that is censored) is under a different account which she named after herself.These two messages occurred right after the "Security Defender" virus removal in which Malwarebytes successfully removed it. Now we're getting these RUNDLL error messages. How can I fix this? Obviously this isn't something good to be popping up after every bootup. What do I do? Please help me.

A:RUNDLL error messages appear at Startup

HiI think your operating system is windows xpClick on start buttonGo to RUN and type%appdata% and click okOn top ,click on TOOLS-Folder optionsClick on View tabSelect -Show hidden filesUncheck '' Hide operating system files'' optionClick okNow you should see the AVI OR ICO file with a lengthy name as mentioned in the error,DELETE itDelete the same file present in System32 and startup folderGood luck

Read other 13 answers
RELEVANCY SCORE 68

Hi,

Couple of days ago, all of a sudden my XP Pro SP3 OS started booting in 640x480/16 colors mode, plus failing to start the regular startup services and programs, displaying error messages like "Bad Image - ...NvCpl.dll", "Bad Image - ...NvMcTray", "Rundll32.exe - ...this and that" (not always the same). After 5-6 of these messages, desktop loads - sometimes with missing icons - but when I try to execute a program, an error message pops up that necessary resources are missing. After a try or two, fonts are dissapearing from the pop up windows and after a little while the system hangs completely.

This happens every single time I boot in normal mode. The only variation is the number and order of the startup error messages, but most of the times it's the ones I mentioned above.

In safe mode it always boots fine, with network support as well.

I cannot run HiJackThis or any other program in normal mode, I can only access programs in safe mode.

Looking forward to getting your advice. Thanks in advance,

John

A:Bad Image error messages at normal mode booting

With the information you have provided I believe you will need help from the malware removal team. I would like you to start a new thread and post a DDS log HERE and include a link to this thread. Please make sure that you read the information about getting started before you start your thread.It would be helpful if you post a note here once you have completed the steps in the guide and have started your topic in malware removal. Good luck and be patient. Help is on the way!

Read other 4 answers
RELEVANCY SCORE 68

Hey,

I get about 4 rundll error messages @ startup....i have vista and am sure it is virus related..i have two different profiles on the computer one is mine & one is the families...the one the family uses has/had the virus...it isn't affecting mine....let me know what info u need....i have an emachines ts5226..i'm not sure what info u need....

Thanx,
LittleFly
 

A:Vista Rundll Error messages @ startup

Please click here to download and install version 2.0.2 of the HijackThis Installer.

Run it and select Do a system scan and save a logfile.

The log will be saved in Notepad. Copy and paste the log in your next post.

Do not fix anything
 

Read other 2 answers