Over 1 million tech questions and answers.

SCSI Hard Drive Question

Q: SCSI Hard Drive Question

I have a Win2k3 Small Business Server being ran with RAID on 4 hard drives.
1 hard drive just got failed and i replaced it with the "same looking" hard drive.
When i plug in the new hard drive i noticed that it does not match up to the others in size and its not meeting the requirements in size to rebuild.

When i looked closer at the hard drive i noticed the following difference from the other 3 working hard drive and the 1 damaged one:

Part: 9v8006-001
Firmware: e302

The model and brand are the same exact settings but non the 2 noted pieces of information. Do you think this could cause a problem if this 1 hard drive was different from the others?

Just wondering because i never had this happen to a SCSI drive on RAID settings, and yes its set to be auto hot swappable and ready to rebuild RAID - its just not working because of the size..........so it says.

RELEVANCY SCORE 200
Preferred Solution: SCSI Hard Drive Question

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: SCSI Hard Drive Question

You should be able to use it. If that hard drive is slower then the other, it will slow them all down to match it, and your hard drives will only use as much space as is in the smallest drive. That is the way it works with conventional hard drives anyway. I would back up your data if possible first before you try it (if you haven't already), just in case.

Read other 1 answers
RELEVANCY SCORE 78.8

OK you SCSI experts, I've got a question for you. First, the particulars of my computer:

Dell OptiPlex GX110, 733mhz Pentium III, 256 Mb RAM, Adaptec AHA-2940U/AHA-2940UW PCI SCSI Controller with a maximum data transfer rate of 40 mb/sec., Boot drive is a SCSI IBM DCHS04W (4.50 GB) 7200 rpm with maximum data transfer rate of 40 mb/sec. and average read seek time of 7.5 ms.

Now, I just purchased a Fujitsu 18.2 GB, 10,000 rpm, SCSI hard drive, with a maximum data transfer rate of 80 mb/sec. and average read seek time of 4.7 ms.

My question: Will I benefit from the speed and efficiency of the Fujitsu drive by making it the boot drive?

I know that my SCSI controller card will limit the maximum data transfer rate to 40 mb/sec., despite the 80 mb/sec. rating of the Fujitsu, however, will the 10,000 rpm and the low average read seek time of the Fujitsu overcome the limitations of my SCSI controller card to the point that I should make the Fujitsu my boot drive? Thanks in advance for any assistance.
 

A:SCSI hard drive question

I will tell you this... going from 5400rpm to 7200rpm spindle speed makes a major difference. So going from 7200 to 10000 will make a difference.

For me, the decision would be easy. I would put the fujitsu as my boot drive.

It's a bigger drive and it's has better access times.
 

Read other 3 answers
RELEVANCY SCORE 77.2

SCSI vs SATA vs EIDE
What are the differences between all of these?

I'll probably not use SCSI, but I was looking at the WD raptor 10K rpm hard drive (SATA). Do you need a special motherboard or certain controller to run this hard drive? And do you need a special CABLE for it? I have tons of 80pin IDE cables, but those wouldn't work?

Thanks
 

A:HARD DRIVE question - SCSI vs SATA vs EIDE

Nope won't work. Different drives, cables, controllers. Some motherboards now come with the SATA interface built in. For more information check this site out. Its an OLD report on SATAs. Hard drives are now available for SATA use.

http://www.explosivelabs.com/articles/sata/
 

Read other 2 answers
RELEVANCY SCORE 72.8

windows98 is already on my 13gb ide drive, but i have a new 9gb scsi drive which is really fast 80mb/sec,
I would like to install only windows for now so machine boots faster, can i do this and still have other files on existing slower 13gb hdd i.e. games, txt files and pics?
I have managed to make ide drive as slave but i dont know how to go abouts installing win98 on scsi, as machine keeps booting to windows, from the slave drive. And when i attempt to install win98 it tries to put it on the ide drive which alwready has it on.
Do i need to disconnect the power supply to the ide hdd?
Does scsi drives have master/slave jumper setting like the ide?

My new hdd is MAG3091LC on this page
www.fujitsu.co.jp/hypertext/hdd/drive/disk_e.html
 

A:if i have 1 ide and 1 scsi hard drive how do i install windows on the new scsi hd?

Read other 8 answers
RELEVANCY SCORE 62.4

ok i posted eariler and its final the scsi seagate is mine and it looks like im keeping it.ok so i bid on the scsi control card thats ldv and now im looking for a cable . my question does the cable need only one terminator? im new to this so if anyone can help me out on installing a scsi hd it would be greatly appreciated
 

A:scsi hard drive?

You want a 68pin internal LVD cable, it should either have a terminator built in + two connectors (one for the SCSI card, one for the hard disk), or three connectors + you'll need to plug a terminator into it. The devices should be arranged with the SCSI card at one end, the hard disk in the middle and the terminator at the other end. The SCSI card provides termination for its own end (unless you want to put the SCSI card on the middle of the cable, in which case you need a terminator for each end). The terminator must be LVD or LVD/SE compliant.
 

Read other 3 answers
RELEVANCY SCORE 62.4

Hi,

I have a Dell Poweredge SP5166-2 that uses Seagate Barracuda (4.3gb) hard drives put into trays that are slid into the computer and connected to the motherboard. I want to put another hard drive in but it is an HP C2490A (2.1gb). When trying to install it the first times, bios recognizes it and says it is working properly, but it is not displayed under Win2k's logical devices or my computer. It is however displayed under device manager. So, it does exist but I just can't make it work within my computer. I also tried to make connect the SCSI bus cable that goes into the cd rom into the hard drive, but no luck. Is there any master slave config for scsi devices? My understanding is that there aren't any; only scsi ids. Any help is greatly appreciated. Thanks in advance.

Louis
 

A:HP SCSI Hard Drive

Hi,

You can check couple of things.

You may want to check SCSI ID(which usually a jumper or switch on the drive.).

If you want the drive to be C:, check host adaptor which ID is bootable.

Make sure you have a terminator at the end of the chain.

Go device manager and check if your SCSI card has conflict with other devices.

Good Luck,

TJ
 

Read other 1 answers
RELEVANCY SCORE 62.4

Built a WinNT 4.0 server using SCSI raid array. Works fine. Enabled atapi in services and it sees the IDE CD-ROM (master, secondary channel) just fine.

But it won't see the IDE HD (master, primary channel)!

Jumpers, cables, HD all okay.

I'm sure I'm missing something obvious. Anyone have a clue?

Thanks,

Jim
 

A:scsi NT -- how to add IDE hard drive?

Greetings

Can your BIOS see the HD? If not, then your OS has no chance of ever seeing it.

Have you tried it as a Slave on the secondary controller? Or better yet, keep it as a master, and make your CD-ROM the slave on the secondary controller.

You could have a dead primary controller (I know my secondary controller is not functioning... damn, I need a new PC - who wants to help me raise funds for a new PC - any compnay that helps will get free advertising from me ), or a dead HD.

There could be something else wrong, but I am not that great with hardware issues. If you want, I can move this to the Hardware forum.

Cheers

------------------
Reuel Miller
Windows NT Moderator (yes, that does make me biased )

[email protected]

Website: www.xperts.co.za/reuel/multiboot

Every morning is the dawn of a new error...
 

Read other 2 answers
RELEVANCY SCORE 62.4

Hi,

I've just bought some hard drives.
They weren't expensive, i got them in a clearance sale, they are SCSI types.

One of my PCs uses an SCSI hard drive as its local drive 'C',
However this PC has a power supply feed to the SCSI hard drive, and also the
SCSI connector ribbon cable.
Thats two separate cables.
One for signal, and one for supply.

The SCSI hard drives i bought have no feed point for a power supply.

So i don't know how to try them.
They must use some supply to operate, so could it come via the SCSI cable ?
I suppose it must come from there ... ?

Ive never seen ones like this before.

I dont want to try them without checking first.
Any comments or suggestions would be welcome.

Model: WDE18300-6029A8
Made: 26th May 1999

I got eight in all, some like this one, and some others.
Now i'm a bit worried about trying them, as they might try to draw more current
from the SCSI signal wires than they were meant to give.
These ones come in a sort of Slot-in carrier, what difference that might make
i don't know.

Cheers, John
 

A:Some help please in trying to use an SCSI hard drive.

Read other 14 answers
RELEVANCY SCORE 62.4

Hi,

I've got an old computer that we've just been using at the office for payroll and a few other things. The problem is its runningout of hard drive space, so I was just going to install another hard drive, but I forgot that it has a scsi hard drive. I was wondering if i could hook a regular hard drive up to the scsi cable? Any help will be greatly appreciated.

Thanks
 

A:SCSI Hard Drive

No.
 

Read other 3 answers
RELEVANCY SCORE 62.4

My computer is not recognizing my SCSI 70 ghz drive. It keeps saying PXE-E61 failure check cable. It worked fine last night, I reformatted my secondary IDE 40 ghz drive and I could not get my computer to start. I had to disconnect my SCSI drive and setup windows xp on my IDE 40 ghz drive to get my computer to start. It still doesn't recognize my SCSI drive. I need help.
 

A:SCSI 70 ghz hard drive

This generally pertains to a bad hard drive or bad hdd cable same as a "non system disk error" with same solutions.
http://www.computerhope.com/issues/ch000229.htm
 

Read other 2 answers
RELEVANCY SCORE 62.4

Hi everyone,
I wonder if anyone have a good site where it can guide me on how to installed a second SCSi hard drive. I have a HP tc2120 server with one 36.4 Gb drive. I have anotherone just like that. But I never have installed and SCSI drive. I have only done the regular IDE drives. I need some help.

thanks,

AMD2800
 

A:SCSI HArd drive

Read other 9 answers
RELEVANCY SCORE 62.4

Whenever I boot up my old computer, I get a message during bootup that tells me that the SCSI boot device is not installed. I have a SCSI hard drive connected to an Adaptec SCSI pci card. I had just taken the hard drive and card out of that computer and tried to install them on this computer, and it didnt work, so I put it back. I tried running a SCSI utility on the bootup screen, and it didnt even recognise the existance of the hard drive. It wont let me format or anything. If there is something I can do to get it working, then please post. I do not care if the solution requires reformatting, because I do not have any really crucial data on the drive.
 

A:SCSI Hard Drive

Read other 9 answers
RELEVANCY SCORE 62.4

I was able to salvage an old system from the trash at work. It has a Western Digital 4.3GB SCSI hard drive and I want to know if i can use it in a non-scsi system. To use it will I have to use a SCSI adapter or have to have all HD's as scsi?
 

A:Using SCSI Hard Drive

You can use it if you have a SCSI adapter and you can mix IDE and SCSI in the same PC.
 

Read other 1 answers
RELEVANCY SCORE 62

I am helping my brother in law out trying to do a non destructive repair using the installation disc. When we went through all the steps and got to the section that shows the hard drives it does not recognize the hard drive and won't let us do a repair. If we wanted to do a clean install it still would not recognize the hdd.
I decided to check bios and see what was recognized and in the hdd section it showed that the hdd was a SCSI. It is not a SCSI drive. We checked PC Wizard 2008 and it showed SCSI. All the places show that it is a SCSI. What is causing this? It is not a SCSI drive but a SATA drive. Can anyone tell me what has happened?
 

A:Hard drive recognized as SCSI

it is SCSI emulation. Some USB drives show up this way too.
 

Read other 4 answers
RELEVANCY SCORE 62

Does anyone know of a website that I would be able to find the drivers for a scsi hard drive? I have been searching for what seems like weeks now and can't seem to find anything.

A:SCSI Hard Drive Driver?

The driver you probably need is not for the SCSI "drive" itself. It's for the SCSI "host adapter" to which the drive is attached.

Please give brand/model specifics of your machine... laptop or desktop (probably) and type/model/details, SCSI drive (internal or external), SCSI host adapter to which the drive is cable-connected.

thanks.

Read other 5 answers
RELEVANCY SCORE 62

hello,

im going to setup a IBM Xseries 235 server in my home soon. I bought several drives. I noticed that one of the drives i bought is a scsi drive that runs at 7200k and the other drives run at 10000k. i bought two 7200k hard drives and 4 10000k hard drives. the server only supports raid 1. Would it be okay to create 3 raids. My computer supports up to six scsi hard drives. Can i create a raid with two 10000k hard drives to host my operating system and a little data, a second raid for my web server data and the third raid for my 7200k hard drives for ...idk, music.?

does that sound like it would work. would the 7200k hard drives slow down my computer?
is it possible to create 3 raids on a single server?
 

A:7200rpm scsi hard drive

bump
 

Read other 1 answers
RELEVANCY SCORE 62

I have a SCSI Hard disk, that i some how messed up by transfering it to a different controller, cuz i didn't know that you can't do that, i do now. i tried to get it to come back alive, by puting it back on the controller, but my master partion table thing got messed up, when i had tried to use it on the other controller, the first controller was a LSI Logic, and the second was an Adaptec 2490-UW. so i tried to use diskprobe to read the sectors and set it up like that, which failed. i thought it might have something to do with the board so i had taken that off, but now when i go into the Adaptec "SCSI-Select" program it doesn't show a size. could i have connected my board back up the wrong way?? it does still spin up, but i don't understand why it lost the size of the disk. it had the size before btw. it is a 18.2 GB 10K RPM SCSI-2 drive, and i have 2 other identicals if they may be of any help. but i really want to know if this drive is toast.
EDIT:: COMPAQ Model #: bd018734a4
 

Read other answers
RELEVANCY SCORE 61.2

How do I get Windows XP Pro to duel boot from a second scsi hard drive. First scsi hard drive has Windows ME and works fine.
Second scsi hard drive has Windows XP pro but only works when I change the scsi ID from 1 to 0. But then the other scsi hard drive is not reconized in windows explore. However, it is reconconized in the XP disk manager and everthing else appears normal excapt that the drive is not read in explorer. Any help PLEASE
 

A:Duel Boot XP on second scsi hard drive

Was XP installed with both HDs in the machine, and with Me installed first? If you installed XP with only its HD in the system (so it was 0 when you installed it), the XP boot files are on the wrong hard drive. They need to be on the system's primary partition, which should be C: (where Me should be now if this is going to work right and properly dual-boot) and the ARC path in your boot.ini file is referencing the wrong disk for the XP startup to look on to boot XP when you have both disks set up.

Please post the contents of your boot.ini file here, and we will take a look.
 

Read other 1 answers
RELEVANCY SCORE 61.2

Gigabyte GA-6LX7 Mb, 400 MHz celeron, 64 meg ram, 13.6 gig Maxtor ide hard drive, 9 gig Seagate scsi hard drive, win 98 se, DTC 3502A scsi adapter, Toshiba scsi cd-rom.
My scsi cdrom works fine, but. I can look at the scsi hard drive in windows and it says that it is only 19.2 meg, I can't access it in windows or dos. The on-board bios for the adapter doesn't find the hard drive or the cd-rom, but, I can still access and use the cd-rom drive.
Also, with ASPI3520.SYS enabled, the adapter and the primary and secondary ide controllers are disabled in device manager, it also makes A: drive use ms-dos mode compatibility.
I used the setup mode of the adapters BIOS to format the hard drive, After it formatted and I continued it says that it can't find a scsi hard drive.
 

A:SCSI Adapter/hard drive problem

Did you run FDISK and see if the drive is visible there?

Are you sure you have your SCSI termination correct?

If there are 98 drivers for your card you shouldn't need to load a driver file in the CONFIG.SYS - as you have seen it will put you in compatibility mode if you do.

Just checked the DTC site - it says:
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Windows 98 Drivers

Included - Use built-in Adaptec 151x/2x drivers <HR></BLOCKQUOTE>

Is that what you are using?

------------------
Get free stuff and help out a poor computer tech
(5/20 new, unlimited, pay to surf site added):
http://www.rkfdcore.com/ebaypics/referrals.htm
 

Read other 3 answers
RELEVANCY SCORE 61.2

hi my new sata hard drive is showing as a scsi in win7
and it seems to be running slow and making alot of accessing data noises
how can i fix this back to sata
thanks

A:new sata hard drive showing as scsi in win 7 help

With some hard disk controllers it is normal for it to show up as a SCSI disk - particularly if the disk controller is running in AHCI mode, which is preferrable since it allows features such as NCQ. One thing you may want to check is: locate the drive itself under "Disk Drives" in device manager and go into the properties. Select the "Policies" tab and view what is set. For better performance you will want it set to "Better Performance" with both of the boxes checked. Though if you lose power you may run into minor file corruption issues - I personally have not had issues with this. If you disable those check-boxes performance can decrease significantly.
 
-David Betournay

Read other 1 answers
RELEVANCY SCORE 61.2

can some help me,i am trying to install 2 4.5 gig SCSI hard drives in windows 2000 .i an useing pci scsi card controller.
i load win 2000 boot disc,s my system finds scsi,s no problem
i format them and partion them .when it reboots to start loading windows it say cd rom error ! INSERT BOTT DISC AND RUN AGAIN
any body got any pointers...

thanks ....rog
 

A:two scsi hard drive install in win 2000

Read other 8 answers
RELEVANCY SCORE 61.2

*RESOLVED* Can't install second U160 SCSI hard drive

I have DL145 G2 from HP
http://h50043.www5.hp.com/Enterpris...nt/questions.aspx?cnty=th&cat=DL&ser=145G2#g1

On the black thing that is attached to the cable which seems to be a controller, it says U320. It originally came with U320 SCSI hard drive but I purchased two U160 hard drives because I was a *****. I connected one U160 SCSI hard drive to the server and installed windows os without any problem. But when I tried to connect the second SCSI U320 hard drive, it didn't work. In the BIOS, it correctly recognized two hard drives but when windows 2003 server loaded, I couldn't see or install the second hard drive. I read some FAQ in the link I copied above and I thought that I have to purchase optional SCSI cable or my U320 SCSI cable only supports one U160 SCSI hard drive or something... But I don't see any place to plug any more cables on the motherboard so I'm really puzzled...

I use two SEAGATE ST3146854LW 15K 68 PIN U160 DELL M6616
and my server is DL145 G2 AMD Dual-Core Opteron 275 2.2GHz 390845-001
 

A:Can't install second U160 SCSI hard drive

So the BIOS sees both the drives?

What do you mean by Windows not seeing the hard drive? You did check in the Disk Manager, right?

SCSI is pretty much backward compatible, so your U160 drives should work no problem. And you can hook up 15 of them to a single SCSI cable no problem.
 

Read other 8 answers
RELEVANCY SCORE 61.2

I am about to build my own PC. It will have a Maxtor Sata hard drive. When you are installing Windows XP Pro, do you have to press F6 and install a third-party driver? I was reading this book, and the guy said to do that. I have never heard about that before. Can you just hit install XP and let it do everything? Thanks.
 

A:Installing Windows Hard Drive SCSI

Yes you need to hit F6 to install a RAID driver. You will be able to get that driver from the motherboard manufacturers website in most cases. The resulting RAID driver that you get will need to be on a floppy, so if you were planning on not putting a floppy in the computer you were building (like many do), you will have to at least have a floppy during the setup process of Windows. Sorry, theres no magic "hit install XP and let it do everything"
 

Read other 5 answers
RELEVANCY SCORE 61.2

Long story short.. An office I help out had a RAID Array crash without a backup. The data has been recovered and is sitting on a Fujitsu Hard Drive (Model: MAX3036NC).

My computer, and the remaining working computers in the office are all IDE or SATA architecture.

I'm guessing there is a PCI SCSCI Card that I could buy, install this hard drive and access it that way. If that is the case, could someone recommend a card/manufacturer that would work for this case?

Any help is appreciated.

Edit: We also have a laptop available if there is a PC-Card solution.

Thanks,
 

A:Solved: Need to access a SCSI Hard Drive

Read other 6 answers
RELEVANCY SCORE 61.2

Just tried to install a SCSI hard drive on a win98 system.

Drive is in Device Manager but has no Letter assigned. Does not allow me to.

BIOS recognizes drive and assigns D:
 

A:SCSI Hard Drive - No Letter Assignment

Read other 7 answers
RELEVANCY SCORE 61.2

As per the norm, I got a Monday call from a customer freaking out about their server. I paid them a visit and sure enough the Western Digital SCSI hard drive I replace about 6 months ago is dead. SCSI utility is seeing it as a 1MB quantum. I told them to boat anchor that machine and get a new one. It's a pentium (i don't remember) 600MHz machine so it's a bit of a dinosaur anyway. their book keeper is the hero of this story. I taught her how to backup the server which she did before she left on Friday. I loaded backup files on an unused workstation, mapped some network drives and had them back up and running PDQ.

What would make a machine eat hard drives? Thin it might just be a fluke, virus, inferior Dell product??????
 

A:2nd SCSI hard drive failure within 1 year

Is there a UPS or surge-protector installed between wall-socket and PC?
If not, unstable electricity might cause that, such as spikes, brown-outs or black-outs.
Or the PSU might be on the edge of its capacity. If the HD is a 10'000 RPM disk, they need a pretty good and stable PSU.
The disk should still be under warranty.
 

Read other 5 answers
RELEVANCY SCORE 61.2

Hello all,

I have an HP Workstation XW8200 running Windows XP SP3 that I tried hooking a projector to. I used a VGA splitter with one out going to the monitor and the other going to the projector. When connected while the computer is already running, the projector works. But once the computer is off, with the projector connected and running, and then the computer is turned on, it no longer recognizes my hard drive.

This problem is NOT fixed when the projector/splitter is disconnected.

In the BIOS, the hard drive is recognized but it will not boot. I tried booting into a Windows XP disk and running recovery mode, but it doesn't see the drive. Same goes for booting off of my thumb drive into Linux (Lucid Puppy 5.2.0), it does not see that I have any hard drive installed.

This has happened to two computers already, both are the same model and setup.
The hard drive in question is connected to onboard SCSI, and is a SeaGate Cheetah, I'm not quite sure what size.

I did take another hard drive from a third HP XW8200 and put it in to the non-working computer and it booted fine.

I do not see the projector causing the computer to not recognize the HD, but it definitely seems to be the catalyst for both of these computers (with each individual problem happening months in between, and over a dozen other similar computers still working fine).

Any help would be greatly appreciated, I'm at my wit's end.
Thanks,
L_C

Oh, and there are no error messages when trying ... Read more

Read other answers
RELEVANCY SCORE 60.4

Ok I have a external enclosure that is IDE / Sata , I have 2 hard drives I'm not using , there both SCSI 10,000 rpm Hard Drives, my question is how can I connect one of them to my external enclosure so I can connect em to my USB

A:Connecting SCSI Hard Drive to my external enclsoure?

You cannot do that. Your drive which is SCSI will not connect to an IDE/SATA controller in the external hard drive enclosure.

Read other 4 answers
RELEVANCY SCORE 60.4

My first build: Via Kle-133 mb with Athlon 700 and 64 sdram
on board video and sound and 9gig Seagate Hard drive needing a scsi-2 thingy

My problem...
I power up and all things begin running and on the monitor it whizzes past the first screen that reports the "Award Modular BIOS v6.00pg, An Enery Star Ally etc...
Main Procecessor: AMD Athlon (TM) 700MHZ
Memory Testing:57344 ok + 8192k Shared Memory

Primary Master: None
Primary Slave: None
Secondary Master: Toshiba CD_ROM XM-5602B 1796
Secondary Slave: None

Floppy disk(s) fail (40)

Then immediately a black screen which says
BusLogic Inc BIOS Version 4.94G
Intelligent Bus Master SCSI Host Adapter
(c) 1995 BusLogic Inc. All Rights Reserved

BusLogic PCI SCSI Host Adapter Firware Version 4.28D
Press <Ctrl-B> to Enter AUTO-SCSI

Which I do the <Ctrl-B> thing and it takes me to a configuration Utilities and Diagnostics program. I try to push the right buttons
Under Utilities and under SCSI Device Information it says
SCSI ID 3: SEAGATE SX910800N
SCSI ID 7: BusLogic BT-946C
(which makes no sense since the hd is a Seagate st410800N)
Under Verify Disk I get the same result

OK then I try the Format Disk option
and the same exact result box comes up with SEAGATE SX910800N highlighted... when I press enter, it asks: CONFIRM? yes or no, I highlight yes and enter and then.... a freeze.

Now if I reboot it will do the same thing every time.
If I ignor the Press <Ctrl-B> to Enter AUTO-SCSI thing, the puter will g... Read more

A:New computer built hard drive with scsi problem

Read other 11 answers
RELEVANCY SCORE 60.4

Hello, this is my first post here. I have an HP Workstation x4000 I use at work for Designing CAD Models. This is an old computer. My problem is that I am out of room on the Hard Drive. It is a 58 GB SCSI,68pin HP Hard Drive. My IT support guy purchased me a 1GB SATA Drive,Raid Card,enough Memory to fill the MEC Card, and Norton Ghost to flash over the new Drive. My problem is, the Card he bought will not fit into the Mobo. The ribbon in the Computer has an empty plug and a power plug,but they are for a 68 pin SCSI Hard Drive. Is there a cable made that I can use to simply plug the SATA Hard drive into the 68 pin ribbon,or do I need a card? Do they make such a thing? My boss is extremely frugal and doesn't want to hear that the best thing would be to replace the 12 year old computer! Thanks for any help you guys can give me
 

Read other answers
RELEVANCY SCORE 60.4

I have a Dell Tower Computer (Circa 2000-2002) that runs RIP software (Raster Image Processor) used to send graphics/image data to a machine that makes by way of laser imaging our plates or masters for our offset printing presses. Monday the hard drive failed. The Dell has Windows XP license decals on it but when booting up it display Windows 2000 NT. The computer has only 1 hard drive, a 68 pin SCSI drive and the cable to it connects to separate dual channel SCSI card which is in a slot on the motherboard. There is another SCSI card (single channel) in the slot next to it which has a cable that goes to the machine that this computer drives. The software that runs on this computer is proprietary software and I have a re-install disk for it being send via UPS Next Day Air as I type. I have an XP disk & license that I can install on what ever hard drive I can get to work here and the RIP software manufacturer said their software would work on XP. But I don't have a copy of Windows 2000 NT.

My question is that if I can't find this same hard drive locally, can I use an IDE or a SATA hard drive instead and still run the RIP software correctly? There is 2 IDE (primary & secondary) connectors directly on the motherboard. One is used for the CD rom drive, the other is unused. I am not certain but I don't believe the motherboard has a SATA connection. I have 2 good spare IDE hard drives.

If I can't make plates I can't print so I need to get this reso... Read more

A:SCSI hard drive died - can i switch to ide or sata?

Read other 8 answers
RELEVANCY SCORE 60.4

Hello All,

I just got my hands on a Compaq 36.4 gb hard drive (10k RPM). It has an scsi port connector but I don't know how to connect it to my ECS board which is fairly new (one of those SLI-status boards). I might need a converter of some sort. The hard drive model is: BD0366459B , my board model is ECS 945-p ( http://www.digit-life.com/articles2/mainboard/ecs-945p-a-i945p.html ) .

Thanks ahead of time.
 

A:Hard Drive Compatibility?:confused: SCSI to IDE or SATA?

According to this site
Product Name BD0366459B
CD-ROM Drive Compaq CRD-8402B
Hard Disk Drive Compaq BD0366459B; 9.09 GB; Firmware 3B12; Wide Ultra3SCSI
BD0366459B; 145. GB; 291. GB; Firmware B005; Wide Ultra3SCSI
Host Bus Adapter Compaq Integrated Dual-Channel Wide-Ultra SCSI-3 ControllerClick to expand...

You need

(1) a SCSI-3 controller to be installed into the mobo
(2) a Wide Ultra3SCSI cable

You may get the hard disk cheap but could get rip off by the hardware needed to go with SCSI equipment.

The Sata can be viewed as a poor man's SCSI but at least your mobo support 4 units out of the box. I doubt if a SCSI can be cheaper than Sata nowadays which is being retailed at GBP 0.128 per Gb. Thus the 36.4Gb unit would cost no more than GBP 4.65 in UK which, if being a Sata disk, is equivalent to approximately one imperial gallon of petrol. That amount of money will not be able to buy either one the above two attachments required to run the unit.

Technically if you run a Sata Raid 0 to half the access time it should beat the SCSI disk performance hand down, I would have thought.
 

Read other 1 answers
RELEVANCY SCORE 60.4

I have been trying to determine which device would be best suited for cooling a pair of SCSi 15k HDDs. I have been looking around at some of the following (in order) of interest. Sound dampening is not a huge concern, mainly concerned about cooling.

Smart Drive 2002 Copper Hard Drive Enclosure- SCSI compatible? Little documentation to indicate if rear is already equipped with wiring or is this will work with SCSI cables?
AEROCOOL HB-101 Hard Drive Cooler Aluminum- Wondering if this is a gimmick or a real option... or a SilverStone SST-FP53-B 5.25" Hard Drive Cooler or a Cooler Master CoolDrive 3... ??? Any other reccommendations based on experience or reviews? Thanks in advance for any help.
 

A:NEED serious advice about Hard Drive Cooling (Pair of SCSI 15k)

if you haven't already bought a case, buy a case with a hard drive cage fan and put it to use. for internal enclousures, all same size drives and cages are compatible. just make sure you have cool air blowing on those drives and they should be just fine.
 

Read other 2 answers
RELEVANCY SCORE 60

Hi I have an old proprietary graphics system that needs a SCSI hard drive, I found a Compaq C2247 1gb hard drive that should work (cylinders,heads,etc match one of its table drives) but it doesn't turn itself on when the PC is powered on.

The drive works perfectly in my new system as long as I have the "send power on signal" checked in the bios.

Is there any way of jumpering this drive so it turns on the instant power is applied as opposed to sending a signal to tell it to turn on?

Thanx
Ryan
 

Read other answers
RELEVANCY SCORE 60

How do you get the power to your hard drive. The power supply has no extra wires or anything. Where does it come from?
 

A:{SOLVED} im a begginner, installing a new hard drive (scsi) so this may seem silly,

Read other 8 answers
RELEVANCY SCORE 60

This is my first attempt at building my own pc so forgive me if this is a silly question.

This pc has an SCSI as the primary drive (17gig) and I'm trying to add two 320g drives that are edi drives.

I added a new dvd drive, video card, and usb 2.0 card and those all work fine.

I tried the drives set to slave as well as well as cable select. I even removed one of the drives so that the only connector is the edi slave connector.

Am I having a problem because I'm trying to use an SCSI drive and the two edi drives? Do I need to use one or the other in order for this to work?

Any help would be greatly appreciated.

Let me give a little more information if it helps. The computer is a Dell Precision 530 Workstation. Company upgraded all their pc's and sold off the old ones for $50 each. I want to ue this as a media server for my home network.

It has a 17GB SCSI drive on it now that has my Windows XP Home Edition and a few other programs on it. I was going to keep it for exactly what it does now. Basic everyday pc duties.

I wanted to add two bigger drives for storage. The mother board has an SCSI connector and two EDI connectors. The secondary EDI connector is connected to the DVD drive and the CD drive. Obviously I don't need both but just left the cd drive in there since it wasn't hurting anything. Those both read and work fine.

I have the two 320 GB storage drives connected to the primary EDI connector.

The ribbon cable attached... Read more

A:PC won't recognize extra hard drives (edi) primary is SCSI drive

Hold on a minute... edi you mean IDE or eIDE don't you?

SCSI hard drives need to have terminated cables. IDE cables do not use termination. I would ditch the SCSI, but you will have to get into the bios settings and change the primary boot drive settings
 

Read other 8 answers
RELEVANCY SCORE 59.2

Hello all. This is my first post here. I Bought a scsi hard drive.

Maxtor 18GB SCSI Hard Drive
Formatted capacity: 18.4GB
Interface: Ultra160 Wide LVD SCSI-3, 80-pin (80 to 68-pin SCA adapter included)
Rotational speed: 10,000 RPM
Average seek time: 4.7 ms
Cache: 8MB

I have the ASUS a7n8x deluxe mother board. What pci scsi adaptor card do I get to run the hard drive? What cable do I need?

This is my first time using a scsi drive. I did a search on newegg and saw a range from $22 - $400+. Please educate me in the ways!
 

A:Installing a scsi hard drive on an asus a7n8x deluxe board

Anything from Adaptec is perfect, but not always the cheapest.
It's what I use on no less than 3 of my PCs.
http://www.scsi4me.com/index.php?menu=menu_scsi&pid=213&display=39160.htm
Brandnew Adaptec ASC-39160 Dual Channel Ultra160 SCSI Controller, $139.-

http://www.scsi4me.com/index.php?menu=menu_scsi&pid=3237
Brandnew bulk LSI Logic LSIU160 single channel Ultra160 all purpose controller $35.-

They have a whole collection of others, as well as loads of information there.
You could try and pick up a used card on Ebay as well.

You will also need a 68-pin internal flatcable with a terminator.
Look around on that website.

Also go to
http://www.adaptec.com/worldwide/pr.../SCSI&prodkey=talk_about_scsi&type=Technology
for a bit of background.
 

Read other 2 answers
RELEVANCY SCORE 59.2

Hello,

I have a BIG problem here with a SCSI drive on our web server in our school.

All of a sudden i keep getting Start Unit Request Failed at start up.

and then when I try to verify the HD on the SCSI menu I receive an
"UNEXPECTED SCSI COMMAND FAILURE" with above a SENSE KEY: "NOT READY".
Like it says, it's not ready.

now this is the secondary hard scsi disk, my primary bootup disk is fine, when i boot up windows, it boots up fine, but doesnt see the e: drive. in device manager though it is there and it says it is working properly.

Do you think it could be the hard disk has failed. only last week on this same server the power supply went. and we changed the power supply. could thsi be related?
Thanks

Ranj
 

A:SCSI hard drive problem. Start Unit request failed.

Try reseating the connectors to the drive. You might swap the power connector between the two drives. Maybe something was bumped when the power supply was removed. If that doesn't work then probably the drive has failed. I take it that the secondary drive is on the same cable as the primary one and it was working ok before the supply went?
 

Read other 1 answers
RELEVANCY SCORE 55.6

I had a thread earlier and forgot to ask a couple of questions.

I was told I could take a hard drive from a windows 98 computer and the person is buying a new Windows xp so I can hook up the win 98 hard drive as a slave to the new computer with win xp so I can drop and drag or cut and past files that they want off the 98 hard drive put on their new computer.

Now If their new computer with the win xp on it, if there is an ide cable going to the hard drive and nothing else then I can hook up the win 98 hard drive to the same ide cable as a slave and no problem.

However if the windows xp computer has the hard drive on the ide cable and also the cd-rom then is it ok just to hook up another ide cable to their mother board and hook the hard drive from the windows 98 computer on the end of that ide cable as the master? and by turning the computer off, and then hooking up the hard drive and then turning the computer back on it should reconize the windows 98 hard drive in my computer right away right?

If I would have to put the windows 98 hard drive in the new computer on a seperate ide cable is it ok to have it as master? cause the hard drive that is already in it would be master to but it would be on a different ide cable.

I am hoping the new computer just has the hard drive on an ide cable by itself so I can just hook the other one up as a slave and get the files and be done with it.

How ever if someone could give me a couple or three scenario's with ide cables and hooki... Read more

A:Solved: windows xp hard drive with win98 hard drive-question if someone has time??

Yes - you understand it correctly
 

Read other 3 answers
RELEVANCY SCORE 53.2

Hello, I have a quick question about cloning a old hard drive to a new hard drive on a desktop computer.

I bought a new 320 GB EIDE hard drive (my computer uses IEDE not SATA) about 3 months ago.
I successfully installed it and it works, but when I set it up as a secondary (slave) hard drive (when I say set it up I mean: physically on the hard drive before I installed it into the computer, I put it to slave not master; and I virtually set it up to a slave hard drive when the computer booted up and all that stuff).
Then I put a music folder in the slave hard drive, that's it.

Now, about 3 months later, I see that I should have just set up my new hard drive to be the master hard drive because my old 70 GB hard drive is just way to small to be used for a computer.
I want to clone my old hard drive to the new hard drive (I want to boot on this hard drive and have everything that was on the old hard drive). I also want to set my new slave hard drive to the master hard drive and the old hard drive to the slave. I looked on the internet and youtube and I know how to clone so I'm alright there.


So since I want to set my slave hard drive as the master:
QUESTION: Do I take my new hard drive out of the computer and physically switch it to master BEFORE cloning, or AFTER cloning (because I'm sure you have to physically do this on the hard drive right? not just virtually through a program)? And do I have to put the new hard drive where the old hard drive cur... Read more

A:Need Help Cloning Old Hard Drive to New Hard Drive (quick question)

Never mind...I figured it out.
 

Read other 1 answers
RELEVANCY SCORE 50.4

So I've got one 80GB drive that I use to store my Windows XP operating systems, all my programs, games, etc.

I also have an 180GB drive that I want to partition into possibly 3 drives, one for music, another for movies, and another for game installation files.

My question is, what exactly do I format the 3 partitions as? Extended, logical, primary, I have no idea which will make the drives stay "available." The problem is that once I finished partitioning the drives the first time, the next day the last 2 partitions became unavilable.

Anyone got any ideas?
 

A:Question about formatting a second hard drive to serve as a storage drive...

Read other 6 answers
RELEVANCY SCORE 50

Heya guys!

I have googled this and I cannot find a reliable procedure on how to unlock a hard drive.

It goes like this: Someone's xbox took a crap and they offered me the hard drive that is inside. They told me it was blank last they check, but that it cannot be used for a pc.

It is the same drive they sell anyone for a pc.. (It's a Seagate U series 5 15gig)

I have an external usb hard drive enclosure, so I popped it into there and several things happened. The computer saw a 'disc drive', but under "computer management" > "disk management" it doesn't list it at all like it would for a drive that you could format.

When I try to restart the computer it actually locks the system if I have it on, and it appears that they 'lock' these drives for the xbox. The person who gave it to me also told me I'd never be able to get it to work for my pc, yet it seems like it should be able to considering that it is the same hardware as in my computer.

Any ideas or direction? I simply want to format it, then keep it in the external enclosure so I can store files on it.
Thank you to anyone who has creative input on this thread!
 

A:the Gift? A hard Hard drive question

Basic info on this drive; http://www.xbitlabs.com/articles/storage/display/seagate-u5.html

Seagates info; http://www.seagate.com/support/disc/iguides/ata/u5isheeta.pdf

Info from Dell; http://support.dell.com/support/edocs/storage/029en/

When I try to restart the computer it actually locks the system if I have it on, and it appears that they 'lock' these drives for the xbox.Click to expand...

If the machine locks with it installed, you may not be able to find a work-around. If you can get the machine to boot with it installed, the "Unlock" command, or a hard disk utility such as KillDisk may stomp on it, thereby enabling a setup/partition/format on the disk.
 

Read other 3 answers
RELEVANCY SCORE 49.6

I am wanting to build a new computer. I have an HP 5p scanner that runs on a Symbios Logic 53C416 ISA SCSI adapter. I don't want to replace the scanner. Should any PCI SCSI adapter work, without any major headache? Is there any other alternatives such as a USB or Firewire adapter/converter? I know I can get a new MB with atleast 1 ISA I was just curious. Thanks for any info.
 

A:ISA SCSI Question

From my experience, HP scanners use a fake SCSI system where the pinouts (and sometimes pin layouts) are not consistent with normal SCSI. In a nutshell, you need that card for that scanner. I may be wrong about this, its been awhile since I used that line of scanners.
 

Read other 3 answers
RELEVANCY SCORE 49.6

In a book I have a question that I got wrong but thought was right.

Two SCSI hard drives are installed on the same SCSI bus. Which statement is true?

a. The two SCSI drives must have the same SCSI ID.
b. The two SCSI drives must have different SCSI IDs and one must have SCSI ID 7.
c. The two SCSI drives must have different SCSI IDs.
d. It does not matter which SCSI IDs the drives have.

Now the book says the answer is d but I thought it was c because I thought that all SCSI devices must have a different ID to prevent conflicts.
 

A:SCSI question

"C" is correct. I can recall a couple of times in school when I got an answer counted wrong on a test and challenged the instructor on it. The answers in the teachers book are not always correct.
 

Read other 3 answers
RELEVANCY SCORE 49.6

I have a bunch of old computers in my attic, so I took them apart and salvaged what I could. There were a couple SCSI floppy drives (the actual 5.25 inch floppies) and some SCSI cables. At least I think they were SCSI, I'm not really sure since I've never actually seen one. But the drives have connectors like PCI cards, and the cables had the slots for them. The cables also had IDE connectors on them, so my question is, can I still use these cables? The drives aren't really worth using, but I like to save what I can, so i figured I might as well keep the cables. There were also some other SCSI cables, I'm guessing they were for hard drives.

If I were to get an old SCSI drive, just for fun, what would i need to run it? Each cable connects to the motherboard the same way an IDE cable does, I assume, so would I need anything different to run them?
 

A:Question about SCSI....

I think what you have there is the old style floppy drive crossover cable. the IDE style connector is probably at each end and the connector that you believe to be SCSI is between them, the one that attached to the 5.25in drive. part of the ribbon twists at one of the IDE style connectors. A SCSI cable has anywhere from 2 to 7 connectors on them and they are 50 pins, so that makes the connector longer than an IDE. I hope this helps.
 

Read other 2 answers
RELEVANCY SCORE 49.6

I have a printer on my network thata can take a SCSI CDROM externally. Is there a way to determine what type of SCSI from the port alone? I know there are a bunch of different kinds of SCSI out there (ultra-wide etc.)
Mike
 

A:SCSI question - how to tell?

I seriously doubt that a printer would be looking for an UW SCSI drive. My guess is it's a normal single-ended SCSI-II 8 bit interface. What does the connector look like, a 50 pin ribbon connector?
 

Read other 2 answers