Over 1 million tech questions and answers.

Systems runs in safe mode - Normal mode locks up

Q: Systems runs in safe mode - Normal mode locks up

I have a HP Pavilion A6352c desktop pc. I have recently installed a clean copy on win 7. I have listed the issue I am having below. I hope you can assist me in getting this system to a stable state.

1. System locks up running in Normal Mode - I will take about 3 minutes before the entire system locks up, I have to do a hard shutdown when this happens. I can start the system in Normal mode, but only if I use the diagnostic startup option in MSConfig. I can enable some services, but I am in the process of trying to figure out which one is making it lockup.

2. The system will run fine under safe mode with networking and such. I have the normal startup option in msconfig enabled in safe mode and no issue except it's in Safe Mode!

I have attached the requested documents/files in the attached zip file. I was unable to get the Perfmon report.

I look forward to your response.

Thanks in advance

SCA

RELEVANCY SCORE 200
Preferred Solution: Systems runs in safe mode - Normal mode locks up

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: Systems runs in safe mode - Normal mode locks up

The dumps are all over the map, but they all are having issues in amdk8.sys (the OS's CPU driver). What's really interesting is one of these dumps looks almost exactly the same as the issue that is documented in KB 975530, but that's for Intel CPUs running hyper-v. However, you *are* running into a watchdog timeout on the CPU (it's causing other drivers to crash and confuse analyze, but it's not that code's fault that the CPU stopped processing it's requests). This means you might have a bum core on that CPU when entering/exiting C-states. Try running this:
reg add HKLM\System\CurrentControlSet\Control\Processor /v Capabilities /t REG_DWORD /d 0x0007e066

Reboot, and see if it still causes problems in regular boot mode. Either way, you probably need to have that CPU looked at as a potential bad part.

Read other 9 answers
RELEVANCY SCORE 127.6

I recently re-formatted my Sony VAIO since it was starting to run super slow. Now that I re-installed Windows 7 on it through recovery disks, it worked fined for about a day but then the problem came back. The computer is slow at bootup and runs super slow while freezing so many times. I am running it on safe mode right now and its working fine.

I ran hardware diagnostics and everything is fine (Memory, Hard Disk etc.)

I installed Norton Antivirus and Windows Live Messenger after the re-install.

Please help me.

A:Computer runs really slow in normal mode, but runs fine in safe mode

anyone?

Read other 9 answers
RELEVANCY SCORE 123.2

Hello everyone. I have a Compaq SR1954NX Desktop computer that I recently reformatted and installed Windows XP Pro SP3 on. After installing some games and applications, a few days later I shut the computer off for the night. Upon the next morning my USB Mouse, a Creative Fatal1ty 1010, stopped working on it. If I unplugged it and plugged it in a different USB port, it would say "Found device, Creative Fatal1ty Mouse, Your Device is now ready to use." However it still would not do anything. However, upon entering safe mode, it works fine.

I reformatted after this, as I thought it was my mistake, and had only installed one or two small games. However, it just happened again.

Can anyone here help me with this? Thanks in advance.

Read other answers
RELEVANCY SCORE 122.8

Hello, the computer I am concerned with is running Windows 7 with IE8, Microsoft Security Essentials and Malwarebytes Anti-Malware. I am currently in Safe Mode with Networking without issue.

The owner of the computer says that something happened earlier today while he was online that sounds like some false antivirus popup, but he's unsure. Here are the symptoms in normal mode. Every application, from moving through them to opening and closing them, runs exceptionally slow - one to three minutes to open, at least a minute to open internet pages. I noticed that, when in IE, as the pages are loading the IE page disappears and reappears. I am not very familiar with Windows 7 so I don't know if it is related. The computer seems to be getting slower as the day goes on. CPU usage is very high.

So far, I have disabled many startup items that were unnecessary. I ran CCleaner and cleaned up. MBAM was run in both normal and safe mode, full scans, and found nothing. This is also posted in Viruses and Malware, but I'm unsure where it should live.

If you can help, thanks!! I have to work on the Win7 computer from LogMeIn, and may have to get around in safe mode there.

A:Win7 runs extremely slow in normal mode, but nicely in safe mode

I suggest you wait for a response from the malware specialists before looking elsewhere.

Read other 2 answers
RELEVANCY SCORE 122.8

Hi
 
I am looking for help 
 
My windows 7 start in normal mode is very slow.  System is in a loop or is hanging waiting for the hard disk to be free.  The hard disk indicator light is on  all the time ... 
When I start the system in safe mode with networking, the system is fine and nothing is holding the hard disk anymore.
 
I ran minitoolbox and got the following error indications 
 
MiniToolBox by Farbar  Version: 20-06-2014
Ran by Toshiba (administrator) on 21-06-2014 at 22:59:54
Running from "C:\Users\Toshiba\Downloads"
Microsoft Windows 7 Home Premium  Service Pack 1 (X64)
Boot Mode: Network
***************************************************************************
 
========================= Devices: ================================
 
Name: Security Processor Loader Driver
Description: Security Processor Loader Driver
Class Guid: {8ECC055D-047F-11D1-A537-0000F8753ED1}
Manufacturer: 
Service: spldr
Problem: : This device is not present, is not working properly, or does not have all its drivers installed. (Code 24)
Resolution: The device is installed incorrectly. The problem could be a hardware failure, or a new driver might be needed.
Devices stay in this state if they have been prepared for removal.
After you remove the device, this error disappears.Remove the device, and this error should be resolved.
 
Name: Microsoft Teredo Tunneling Adapter
Description: Microsoft Teredo Tunneling Adapt... Read more

A:Windows 7 very slow in normal mode, runs fine in safe mode with networking

Could have crap ton of stuff starting up with windows.
perhaps corupt driver or installed the wrong driver.

Read other 2 answers
RELEVANCY SCORE 122.8

Hello,
 
all of a sudden Windows 7 became extremely slow in normal mode. This doesn't happen in safe mode.
 
The laptop now also makes 3 beeps on startup, but the beeps disappear when Windows login page comes up. The only thing I did is updating Java and the beeps started.
 
I'm sending in attachment DDS, OTL and ComboFix logs.
 
Thanks in advance for your help!

A:Windows 7 runs fine in safe mode, but very slow in normal mode

Hello maestrale,

Welcome to Bleeping Computer.
My name is fireman4it and I will be helping you with your Malware problem.

Please take note of some guidelines for this fix:
Refrain from making any changes to your computer including installing/uninstall programs, deleting files, modifying the registry, and running scanners or tools.
   If you do not understand any step(s) provided, please do not hesitate to ask before continuing.
   Even if things appear to be better, it might not mean we are finished. Please continue to follow my instructions and reply back until I give you the "all clean".
In the upper right hand corner of the topic you will see a button called Follow This Topic.I suggest you click it and select Immediate E-Mail notification and click on Follow This Topic. This way you will be advised when we respond to your topic and facilitate the cleaning of your machine.

   Finally, please reply using the Post  button in the lower right hand corner of your screen. Do not start a new topic. The logs that you post should be pasted directly into the reply, unless they do not fit into the post.  1.Download AdwCleanerDouble click on AdwCleaner.exe to run the tool.
***Note: Windows Vista and Windows 7 users:
Right click in the adwCleaner.exe and select "Run as administrator"Click the Scan button.

Once the scan complete click Clean to finish cleaning any thing it has found.A logfile will automatically open after the scan h... Read more

Read other 28 answers
RELEVANCY SCORE 122.8

I'm not sure what causes my BSOD. The errors range from BAD_POOL_HEADER to ntfs.sys to drivers-something.

I am currently running Safe Mode with Networking and things seem stable.

I ran Anti-malware (nothing found), VIPRErescuescanner (nothing), fakereanfix (didn't help), ComboFix (probably made things worse).

Are my drivers up to date? No, probably not, but at this point, I'm scared to change anything else.
Is my windows 7 up to date? No updates installed since Jan 2012, I'm too scared to update anything lest I cause more BSODs.

Minidump attached in next post.

A:BSOD in normal mode (various errors), Runs fine in Safe Mode

minidump per SF_Diagnostic_tool

Read other 8 answers
RELEVANCY SCORE 122.8

Honestly, I really don't know where to begin. Every time I try to run my computer in normal mode it restarts and gives me options to run in different safe modes or try normal mode again. My computer runs perfectly fine in safe mode. I haven't added any new programs. It's been this way for some time. I'm currently running sfc /scannow to see if this helps, which I seen it helped on a similar forum on bleepingcomputer. If anyone has anything else to contribute, please feel free.

A:Computer runs fine in safe mode but restart when run in normal mode

This is what it's telling me.

Read other 3 answers
RELEVANCY SCORE 122

Hi,

I'm having problems when I load windows in normal mode. When I turn on the computer everything starts as normal. It's after clicking my name and the desktop loads, nothing responds. It just freezes.

I have no problems when loading windows in safe mode with networking.

I ran a full scan through my virus software, Kaspersky. No threats were detected.

I also tried System Restore twice while in safe mode. I'm still having issues.

Any help would be greatly appreciated. Thanks so much!
 

A:Solved: Pc freezes in normal mode, but runs in safe mode

Read other 16 answers
RELEVANCY SCORE 120.8

Hello guys,
you are my last hope! I do not know what I am supposed to do anymore, I spent the last 8hours looking on the net what I could do. I am a computer noob and have little experience with computers at all.

Here's my problem. My laptop doesn't start anymore. The first thing I noticed on my boot screen were four parallel vertical lines of dots, then four parallel lines of vertical dashes then dots again and so on. This is in the background from the time when I start my samsung R70, even on the boot screen, as well as on the windows vista loading screen (these little boxes floating from right to left...). These really weird dots are however NOT present in the DOs menu and neither is it after you pressed F8 to boot in safe mode. They are also NOT present in safe mode that means they disappear after the boot screen and are not evident on the black background of the safe mode desktop.
However at the time when the windows vista sign is supposed to flash up and you'd be prompted to enter your password (this is when I start it normally), nothing happens and a greyish-white screen comes up, after which the system just restarts and the whole process happens again (including the dots mentioned earlier). I can run the laptop in safe mode, in fact I am running it in safe mode with network drivers right now to type this, but I cannot, under any circumstances, run it in normal mode. When I start it in safe mode I get the following notice:

(Yes, I am running a German OS, so I a... Read more

A:Help! Laptop runs in Safe mode but not in normal mode

Quote:





Originally Posted by XQlusive



Weitere Informationen ?ber das Problem [Additional information]
BCCode: 50
BCP1: A33100F8
BCP2: 00000000
BCP3: 820818F8
BCP4: 00000002
OS Version: 6_0_6000
Service Pack: 0_0

Please guys, help me!

I am a year 12 boarding student and I desperately need my laptop to get my work done!

Do you guys reckon that installing a completely new windows vista will solve the problem?

- I do not have the original vista CD with me since I am German and on an exchange to Australia. My dad has the CD and he's about 22.000km away right now.




Hi -

The BSOD bugcheck (STOP error) = 0x50 = invalid memory referenced

As you said - no service packs installed, which is probably one of the problems here. You need to see if you can re-install Windows and then see if it is stable or not.

I do recommend another re-install of Vista using the manufacturer's (OEM) recovery DVD. This must be the first item on the "to do" list. Contact your father or the system manufacturer and obtain the Vista recovery DVDs. Do you have a recovery partition? Many do. Usually, the key to invoke the recovery partition if F10 - during boot-up.

Two other options until your Vista DVDs arrive from your father -
1. Download and burn Server 2008 - it has the same build as Vista, with a few features that have been disabled. It is a trial offer that can be renewed up to 240 days - http:/... Read more

Read other 1 answers
RELEVANCY SCORE 112

Can anyone help me here? My laptop locks up especially when I try running anti-virus. Malwarebytes and Spybot run clean in Safe Mode. I think a virus has taken over. What steps can I take next?

A:CPU locks up but runs fine in Safe Mode - Virus?

Hello my name is Sempai and welcome to Bleeping Computer.*We apologize for the delay. Forum have been busy.*I want you to understand that I'm still a trainee here. I will be working with my Coach who will approve all my instructions before posting them to you, so there's a possibility to have some delays in my responses. But the good part is, there are two people reviewing your problem instead of one.*It is important not to make any further changes or run any other tools unless instructed to. This may hinder the cleaning process of your machine.*You must reply within 5 days otherwise this topic will be closed.1. Let's do a scan with OTS.Download OTS (by Oldtimer) to your Desktop.Close all other programs and don't do anything while the scan is in progress because it may freeze.Double-click on OTS.exe then click Run to start the program. (Do not change any settings).Notes:1. If you are using Windows Vista, please right-click on it and select run as administrator.2. If you are using a Windows 64bit machine, please make sure the checkbox next to 64Bit box is checked.Click the Run Scan button to start the scan.When the scan is complete, It will produce a report and a notepad will open.Click Format tab in the notepad and make sure that Wordwrap is uncheck.Post the entire content of the text file when you reply.Note: If the text file is too big to post, you can attach it instead. The log is located on your desktop as OTS.txt2. We Need to check for Rootki... Read more

Read other 2 answers
RELEVANCY SCORE 112

I was browsing the internet the other day when I clicked on a link and my computer shut down. I immediately knew it was a bad link. My computer rebooted and it wouldn't let me on IE after that at all. I then did a restore to the previous day. I was about to get online so I went and downloaded Kaspersky IS and scanned my computer. My laptop messed up and rebooted itself. Then got Anti-Malware Bytes in Safe mode and ran a scan, still had issues Kaspersky not running right and my computer freezing after just a couple of minutes. Went back and did a restore again to the same spot and this time said forget Kaspersky and jsut did AMWB. It showed my computer is clean, yet about 2 minutes after booting, my computer reboots and the safe mode option pops up. I can run ok in safe mode but cannot get it to work in normal mode. I did trend micros housecall and another online scanner and all say my computer is clean. Yet, when I start IE, I am redirected on every link I click to scour..... or another site with links on it. Any help is greatly appreciated, as well as a recommendation for a better Anti-virus. I jsut had McAfree that came with this laptop. Thanks!






.
DDS (Ver_2011-06-12.02) - NTFSx86 NETWORK
Internet Explorer: 8.0.7600.16385
Run by Mom at 1631 on 2011-06-20
Microsoft Windows 7 Home Premium 6.1.7600.0.1252.1.1033.18.2812.1805 [GMT -4:00]
.
SP: Windows Defender *Enabled/Updated* {D68DDC3A-831F-4fae-9E44-DA132C1ACF46}
.
============== Running Processes =... Read more

A:Only runs in safe, redirects even in safe, reboots in normal mode..no virus' found

oh and Malwarebytes did block a 91-207-192-22 port 49179 svchost.exe

Read other 9 answers
RELEVANCY SCORE 110

Hi,
 
I could use some help. My Toshiba Satellite laptop is having issues after the normal startup with slowing down dramatically after it goes to the desktop. It will basically freeze with commands taking between 5-50 seconds to be recognized and sometimes it just freezes. When I boot into Safe Mode, I am running everything smoothly. I could really use some help figuring out whats going on.

A:Everything runs very slow in normal, but fine in Safe Mode.

Open msconfig and on the General tab choose "selective startup" (uncheck all three items) and reboot. Does the problem still occur? If not, start adding items back to msconfig one or two at a time, rebooting after each change, until the problem reappears and you'll have identified the offending process. This is clearly a time consuming procedure, but it is the best way to determine if some process loading with the system is the cause of your problem.
 
After you've isolated the cause, do not use msconfig to permanently disable the process. Instead, if it is a service go to START - RUN and type: services.msc (then press enter) and disable the service OR, if it a program, you can download & run a simple app such as Mike Lin's Startup Control Panel (http://www.mlin.net/StartupCPL.shtml) to enable, disable, or otherwise manage startup programs.

Read other 1 answers
RELEVANCY SCORE 110

Can someone help me to figure out what is making this happen ? its driving me nuts, my cpu usage goes through the roof, and I am clueless as to what is causing this... but in safe mode with networking it runs fine.... can someone help me ??? many thanks!!!!

Read other answers
RELEVANCY SCORE 108.8

Hi, I navigated to this site doing a google search and finding a post in your forum that was similar to my issue.
 
On 9/20 morning my browser was acting strange like when I clicked the arrow to go back I had to click numerous times and sometime it wouldn't go back at all.   I was running Kaspersky anti virus at the time but wonder if something malicous got in.   When I shut down the computer and tried to restart it took almost 90 minutes to start .  Once it starts and I click start menu or a program on the desktop the it hangs and I'm able to do nothing. 
 
 
I'm able to work in safe mode and safe mode with networking as normal.
 
As recommended.
 
I downloaded super anti spyware and it found only cookies I got rid of .
 
I also downloaded Adware cleaner which found a number of issues which I deleted.
 
Did a malware bytes scan and said I was clean. Tried to start in normal mode and the same issues.
 
 
I'd appreaciate any assistance. Thanks!!
 
 
I'd also like to add trying to use system restore to go back further than the morning of 9/20 but the box in the lower left is missing.  I just used that weeks ago and the box was there when I replaced a video card.
 

A:Vista runs fine in safe mode , slow in normal.

Welcome aboard   Download Security Check from here or here and save it to your Desktop. Double-click SecurityCheck.exe Follow the onscreen instructions inside of the black box. A Notepad document should open automatically called checkup.txt; please post the contents of that document.NOTE 1. If one of your security applications (e.g., third-party firewall) requests permission to allow DIG.EXE access the Internet, allow it to do so.NOTE 2 SecurityCheck may produce some false warning(s), so leave the results reading to me. Please download Farbar Service Scanner (FSS) and run it on the computer with the issue.Make sure the following options are checked:
Internet ServicesWindows FirewallSystem RestoreSecurity Center/Action CenterWindows UpdateWindows DefenderOther ServicesPress "Scan".It will create a log (FSS.txt) in the same directory the tool is run.Please copy and paste the log to your reply. Please download MiniToolBox and run it.Checkmark following boxes:Report IE Proxy SettingsReport FF Proxy SettingsList content of HostsList IP configurationList Winsock EntriesList last 10 Event Viewer logList Installed ProgramsList Devices (do NOT change any settings here)List Users, Partitions and Memory sizeClick Go and post the result. Download Malwarebytes' Anti-Malware (aka MBAM): http://www.malwarebytes.org/products/malwarebytes_free to your desktop.* Double-click mbam-setup.exe and follow the prompts to install the program.* At the end, be sure a checkmark is placed next to Up... Read more

Read other 5 answers
RELEVANCY SCORE 107.6

Hi, after connecting and disconnecting some external HDD using USB to my pc, BSOD keeps showing constantly after 5 minutes from booting to windows .

I checked RAM, and it urned out to be in good shape, then i tried Registry cleaning, but nothing changed .

It works very well and stable under safe mode only, and my best guess that it's my HDD which is not in good shape, but that doesn't explain how it works fine under safe mode, it supposed to crash also, right ?

I have :

Pentium 4 3.00 GHz
4 GB RAM
Nvidia 8400GS

OS : Windows 7 Ultimate 64bit
Sorry for my bad English

A:BSOD in normal and clean boot, runs fine in safe mode

Here is my SF_Diagnostic_Tool results

Read other 5 answers
RELEVANCY SCORE 107.6

Hi,My Computer which has Win Xp Sp3 is behaving like it is in safe mode , eventhough it is in normal mode .I noticed this because ,1. Avira Antivir Guard and Update cannot be launched bcz Scheduler is not running.2 . I tried to start scheduler ( under services.msc ) , but can't start it bcz of error 1084 ( safe mode situation ) .3 . I can't use Windows Update , bcz of error Error number: 0x8007043C ( same safe mode condition )4 . I ensured that BITS was set to automatic , but it can't run bcz of 1084 error.I have scanned with Malwarebytes, Spybot S&D , SuperAnti Spyware ( in real safe mode) - No DetectionHere is the dds log ,DDS (Ver_09-09-24.01) - NTFSx86 NETWORK Run by Administrator at 16:45:23.03 on Mon 09/28/2009Internet Explorer: 8.0.6001.18702 BrowserJavaVersion: 1.6.0_12Microsoft Windows XP Professional 5.1.2600.3.1252.1.1033.18.510.112 [GMT 5.5:30]AV: ZoneAlarm Security Suite Antivirus *On-access scanning disabled* (Outdated) {5D467B10-818C-4CAB-9FF7-6893B5B8F3CF}AV: AntiVir Desktop *On-access scanning enabled* (Outdated) {AD166499-45F9-482A-A743-FDD3350758C7}FW: ZoneAlarm Security Suite Firewall *enabled* {829BDA32-94B3-44F4-8446-F8FCFF809F8B}============== Running Processes ===============C:\WINDOWS\system32\svchost -k DcomLaunchsvchost.exeC:\WINDOWS\system32\svchost.exe -k netsvcsC:\WINDOWS\system32\ZoneLabs\vsmon.exeC:\WINDOWS\Explorer.EXEC:\Program Files\Avira\AntiVir Desktop�... Read more

A:Safe Mode Error, WinXpSp3 behaves like it is in safe mode even in normal mode

Hello and welcome to Bleeping ComputerWe apologize for the delay in responding to your request for help. Here at Bleeping Computer we get overwhelmed at times, and we are trying our best to keep up. Please note that your topic was not intentionally overlooked. Our mission is to help everyone in need, but sometimes it takes just a little longer to get to every request for help. No one is ignored here.If you have since resolved the original problem you were having, we would appreciate you letting us know. If not please perform the following steps below so we can have a look at the current condition of your machine. If you have not done so, include a clear description of the problems you're having, along with any steps you may have performed so far.Upon completing the steps below another staff member will review and take the steps necessary with you to get your machine back in working order clean and free of malware.If you have already posted a DDS log, please do so again, as your situation may have changed.Use the 'Add Reply' and add the new log to this thread.Thanks and again sorry for the delay.We need to see some information about what is happening in your machine. Please perform the following scan:Download DDS by sUBs from one of the following links. Save it to your desktop.DDS.scrDDS.pifDouble click on the DDS icon, allow it to run.A small box will open, with an explaination about the tool. No input is needed, the scan is running.Notepad will open with the results.Foll... Read more

Read other 2 answers
RELEVANCY SCORE 106.4

A few days ago, my wife's computer started running slower and slower, until finally she woke up and saw a black screen that said ""can't come out of hibernation mode - fatal error".  
 
I've tried running the various performance tools, but the computer sputters, chokes and dies before the performance tools screen can even open. 
 
I've cleared temp files, verified there's enough space on the HD, run adaware by Lavasoft, checked to make sure the ram chips are in good shape and plugged in, I've even visually verified that the CPU didn't melt. 
 
I'm not 100% sure, but it seems like there is a connection between the computer slowing down and when it tries to connect to the WLAN. but that may just be coincidence. 
 
And when i run it in safe mode, none of the above happens. 
 
Help?
 
Thanks!
LTVagabond

A:Win7.Dell XPS8300Desk-Runs VERY slowly in Normal Mode, but perfectly in safe

Since this doesn't occur in Safe Mode there is a good chance that this is caused by either a third-party service or startup item.  In order to determine if this is the case, I would suggest performing a Clean Boot. 
 
After you have finished Part C you will reboot your computer.  If the problem doesn't occur you most likely have either a service or startup item causing this.  The process of elimination should find the problem service or startup item.
 

 
***This is a diagnotic tool for Windows Vista, Windows 7, and Windows 8.  This will not repair your computer, but it may point to where the problem lies so that a repair can be made.***
 
Warning:  Disabling items in Services or Startup may leave your anitivius disabled until the process is ended.  For this reason I would suggest that you perform this process off line.
 
Part A
 
(1)  Click on the Start orb, then type msconfig.exe in the Search programs and files box.  
 
(2)  When msconfig is seen in the pane above the search box and under Programs, right click on it, then click on Run as administrator.
 

 
If you are prompted for an administrator password or for confirmation, you should enter the password or provide confirmation. 
 
Part B
 
(1)  Click on the General tab.   
 
(2)  Click the Selective startup option. 
 
(3)  Remove the check mark in the Load startup items &#... Read more

Read other 3 answers
RELEVANCY SCORE 101.6

Hello ladies and gents , im having a problem with my emachine T1120. It starts up and goes through the welcome screen then goes to bios settings , I click on "start windows normally" and enter it and the machine runs right back to the original bios screen , cant figure, unplugged and pressed the power button several times plugged in same result, why? I added no new hardware or software just turned it on and wa la

A:Win.xp emachine starts and runs safe mode, safe mode with networking

hello and welcome to BleepingComputer,,
 
     this is reminiscent of BIOS settings that need to be reset to default. you can do this by using that option in BIOS. do you see the option there? 
 
if this pattern exists after BIOS reset, then there are other XP level options to try like console command /sfc scannow and chkdsk /r
 
 not to long ago, i was dealing with a PC that was doing this same thing, and it was the hard drive (SATA) protocol setting in BIOS, it had to be set to IDE.
 
one more thing, this could be blue screen error that isn't halting, just looping boot. is there an option at the boot screen (the one with the safe mode options) about halting on errors?

Read other 3 answers
RELEVANCY SCORE 99.6

I was shocked when I downloaded TFC.EXE and installed it on my computer AND installed it on my friends computer too from THIS website.now we BOTH have the SAME problem. ha ha I boot to regular mode and nothing works. rightclick on taskbar and then click on taskmanager it stops. doubleclick on AOL or mirosoft update and the hourglass goes around forever. I tried to print something and the printer is gone.I cannot start adaware or avast. sometimes the taskbar loads but most of the time in does not. it is getting worse.. I hope you can help get this thing running.
windows xp home 32bit sp3 thanks again SAL

A:runs good in safe mode.nothing works in regular mode

Can you boot into Safe mode with Networking?You said that nothing works. Please offer more description, what does not work? Can you run or install apps?If you can get into safe mode with networking try a boot scan with Avast and post the results. (Make sure that Avast is up to date first)See here if you need help getting to Safe Mode.

Read other 11 answers
RELEVANCY SCORE 99.6

Hi, I'm having some problems fixing my bleeping computer (Windows 10 desktop computer, to be specific) and could use some assistance.
 
On Friday 15 December 2017, my computer ran fine when I woke up and used it for a few minutes in the morning. Before that date, I had very few problems with my computer running; the biggest issue was some freezing occurring while playing games demanding on processing power such as Civilization 5. However, I don't believe that is related to my current issue, as I last played it on Sunday 26 November 2017, and I had no issues with it on that day.
 
When I returned home later that day (15 December), I found my computer stuck on a blue screen. I'm not sure quite what happened, as my computer was not used during the day at all. I restarted several times, but I was not able to even make it to the user login screen before getting a blue screen. I've received error code 0xc0000142 for every blue screen.
 
Startup repair did nothing to resolve the situation. I am still able to run my computer in safe mode with networking and that's how I'm writing this post. For the past two weeks, I've been using safe mode to use my computer. I've looked online for solutions, but haven't gotten much. I've had some problems in safe mode with random freezes, but at least the computer runs most of the time, although with limited functionality.
 
My research led me to trying Windows + R and opening msconfig.exe and disabling all services that were not... Read more

A:BSOD - Computer runs in safe mode, not regular mode

If you work OK in Safe Mode - but not in normal mode, it's most likely a software problem.
Hardware problems are possible, but nowhere near as likely as a software problem.
 
First thing I'd suggest is trying a clean boot.  It's similar to Safe Mode - but works in normal mode by disabling stuff.
It's also similar to disabling the services - but you'll disable more when doing a clean boot.
If a clean boot fixes the problem - then the problem was caused by one (or more) of the things you disabled for the clean boot.
Then it's just a matter of re-enabling things one at a time until you find the problem.
Perform a Clean Boot:  http://www.thewindowsclub.com/what-is-clean-boot-state-in-windows
If that stops the problem, then re-enable things a few at a time until you figure out what's causing it.
Then uninstall the problem program (from Start...Settings...Apps...Apps & Features - if you don't find it there, check the right sidebar for Programs and Features and see if you can remove it from there).
 
Backup your stuff now.  There's no telling exactly what the problem is - so a backup is the best way to be prepared in case the system dies on you suddenly.
 
If this doesn't work, then post back and we'll ask for some reports to try and figure out what's going on.
Good luck!
 

 

Read other 1 answers
RELEVANCY SCORE 99.2

Please help!  Over the past week or two my computer has been running slower and slower.  Then lost the ability to download anything unless in safe mode.  Now when opening computer in normal mode get nothing but black screen.  Think I got something when my antivirus software lapsed and I wasn't protected for a bit?
 
Running Windows 7 64
 
Tried running Malewarebytes, Avast, SuperAntiSpyware, Microsoft Defender, sf scan, CCleaner and nothing has helped.  Everything comes back fine. 
 
I'm not very computer savy but from what I have been reading you all can help!  Much appreciated and many thanks for any assistance. 
 
 

A:I'm lost. Only open in safe mode. Normal mode give black screen.

Hello ,what is the sf scanBoot to safe mode with Networking and try running these......MiniToolBoxPlease download MiniToolBox, save it to your desktop and run it.Checkmark the following checkboxes:Flush DNSReport IE Proxy SettingsReset IE Proxy SettingsReport FF Proxy SettingsReset FF Proxy SettingsList content of HostsList IP configurationList Winsock EntriesList last 10 Event Viewer logList Installed ProgramsList Users, Partitions and Memory size.Click Go and post the result (Result.txt). A copy of Result.txt will be saved in the same directory the tool is run. Note: When using "Reset FF Proxy Settings" option Firefox should be closed.TDSSKillerDownload TDSSKiller and save it to your desktop.Extract (unzip) its contents to your desktop.Open the TDSSKiller folder and doubleclick on TDSSKiller.exe to run the application, then on Start Scan.If an infected file is detected, the default action will be Cure, click on Continue.If a suspicious file is detected, the default action will be Skip, click on Continue.It may ask you to reboot the computer to complete the process. Click on Reboot Now.If no reboot is required, click on Report. A log file should appear. Please copy and paste the contents of that file here.If a reboot is required, the report can also be found in your root directory (usually C:\ folder) in the form of TDSSKiller_xxxx_log.txt. Please copy and paste the contents of that file here.AdwCleanerPlease download AdwCleaner by Xplode and save to your Desktop.Double clic... Read more

Read other 3 answers
RELEVANCY SCORE 99.2

I need some help please as I do not know where to start.

I installed a Windows Update a few days ago and then got a BSOD the next time I turned my PC on. So I did a system recovery and this seemed to work.

Now, it's happened again without me doing a Windows Update and I cannot get into safe mode.

I am really sorry but I cannot even follow the BSOD instructions to run a diagnostic tool because I literally cannot get into anything to run the diagnostics.

Can anyone offer me advice?

A:Windows Normal Mode Crashes to BSOD and Safe Mode doesn't load

We can offer the best assistance if you would upload the following information
http://www.sevenforums.com/crashes-d...tructions.html

Read other 9 answers
RELEVANCY SCORE 99.2

So my laptop only starts up in safe mode and when I try to access it through normal startup, a blue screen appears for a short amount of time and then attempts to startup again going on and on in a never ending cycle.

However, I got it running on safe mode and ran Malwaebytes Anti-Malware on safe mode (with networking). However, it didn't pick up anything wrong. What can I do to fix this???

A:Vista only starts in Safe Mode and blue screen appears in normal mode

Hi There ghostOnthestage!For a rather lengthy but very informative article on stop errors and what may possibly cause them go here: http://www.updatexp.com/stop-messages.html Perhaps this will help a bit until someone more knowledgeable on this subject can come along. Good luck!

Read other 1 answers
RELEVANCY SCORE 99.2

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft® Windows Vista™ Home Premium, Service Pack 2, 32 bit
Processor: Genuine Intel(R) CPU T2250 @ 1.73GHz, x86 Family 6 Model 14 Stepping 8
Processor Count: 2
RAM: 2549 Mb
Graphics Card: Mobile Intel(R) 945GM Express Chipset Family, 224 Mb
Hard Drives: C: Total - 112971 MB, Free - 52348 MB;
Motherboard: TOSHIBA, IAKAA
Antivirus: AVG AntiVirus Free Edition 2015, Updated and Enabled

I can no longer see my external monitor. I have hooked it up because my laptop monitor no longer has a functioning backlite/

In the past when this happens I used system restore, but now when I try that it says there is no restore point.

HELP!!
 

A:Solved: External monitor black in normal mode but visible in safe mode

The external monitor toggle was somehow unset. fn f5 fixed it.
 

Read other 1 answers
RELEVANCY SCORE 99.2

Hi,

About two months ago my HP Pavilion 6654y Win7, 8GB, etc.,
started running extremely slowly in Normal Mode. It takes several minutes to respond to mouse clicks, etc.
Basically, it just hangs. But it runs "ok" for a minute or two while still rebooting.

In Safe mode it runs just fine.
I've tried everything I can think of to narrow down the problem, to no avail,
including numerous scans such as AVG, Malwarebytes, Trend Micro Housecall.
Installed UnHackMe to check for rootkits. Even got Reimage and ran it several times.

I've used CCleaner to clean things up, and also to clear out Startup programs
and disable most scheduled tasks, as follows,
(though it is confusing to me since I still see some of the process when started up in Normal Mode):

Yes HKLM:Run StartCCC Advanced Micro Devices, Inc. "C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static\CLIStart.exe" MSRun
Yes HKLM:Run KillProcess Orange Lamp Software Solutions "C:\Program Files (x86)\KillProcess\KillProcess.exe"
Yes HKCU:Run HydraVisionDesktopManager AMD "C:\Program Files (x86)\ATI Technologies\HydraVision\HydraDM.exe"
No Startup User Stickies.lnk Zhorn Software C:\PROGRA~2\Stickies\stickies.exe
No Startup User OpenOffice.org 3.3.lnk C:\PROGRA~2\OPENOF~1.ORG\program\QUICKS~1.EXE
No Startup User 1-Click Answers.lnk Answers Corporation C:\PROGRA~2\1-CLI... Read more

A:Win7 fine in Safe Mode, extremely slow responses in Normal Mode.

Please run Minitoolbox and include the List Installed Programs. Check HP desktop if it comes with a diagnostic test within windows or BIOS utility for memory sticks and hard drive and try running the complete test. Please post back if there are no such features as they would be provided. Try also doing some house cleaning for some dust and bunnies to make sure thermal events is not contributing to the problem.

Read other 11 answers
RELEVANCY SCORE 99.2

Hi guys,
it is my first time to join to this forum. I really need the solution of my laptop Problem. I Have my
Gateway EC38 and it has been
freezing while I am using in normal mode.
But in Safe Mode works well. I tried uninstall my video card driver and also my sound card but nothing works. I also do
sfc/scannow in safe mode/safe mode with command prompt, but yet it says I have corrupted file but he doesnt show any file. I check in log file but I dont understand much.
Im always maintaining my laptop hardware status specially ventilation and change every year the cpu thermal gel.
Please help me find solutions to this kind of problem.
My Laptop Details:
Windows 7 64bit
x64 Base processor
factory OS windows Vista
Processor: Intel Centrino 2

Read other answers
RELEVANCY SCORE 99.2

laptop has been randomly freezing. cursor disappears no keyboard function. only thing to do is manual shutdown.

Now getting a BSOD error 50.

any help?

A:BSOD BCCode 50. freezes in normal mode, works fine in safe mode

Code:
BugCheck 50, {fffff80040f9e3b0, 1, fffff80000b9a1aa, 5}

*** WARNING: Unable to verify timestamp for ntoskrnl.exe
*** ERROR: Module load completed but symbols could not be loaded for ntoskrnl.exe

Could not read faulting driver name
Probably caused by : ntoskrnl.exe ( nt_fffff80000b95000+51aa )

Followup: MachineOwner
---------
Your crash dumps are not showing any finite probable cause. In such a situation, it is better to enable Driver Verifier to monitor the drivers.
Driver Verifier - Enable and Disable
Run Driver Verifier for 24 hours or the occurrence of the next crash, whichever is earlier.



   Information
Why Driver Verifier:
It puts a stress on the drivers, ans so it makes the unstable drivers crash. Hopefully the driver that crashes is recorded in the memory dump.

How Can we know that DV is enabled:
It will make the system bit of slow, laggy.



   Warning
Before enabling DV, make it sure that you have earlier System restore points made in your computer. You can check it easily by using CCleaner looking at Tools > System Restore.

If there is no points, make a System Restore Point manually before enabling DV.



   Tip

If you fail to get on the Desktop because of DV, Boot into Advanced Boot Options > Safe mode. Disable DV there. Now boot normally again, and try following the instruction of enabling DV again.
If you cannot boot in Safe mode too, do a System Restore to a point you made ... Read more

Read other 9 answers
RELEVANCY SCORE 99.2

Hello,
 
OS : WIndows XP SP3
 
My computer (actually on loan from my mother in law!) is taking ages to start and when it does, it is very slow to respond and even freezes. Eventually an Avast alert pops up and tells me it detected a rootkit called "Catchme". I didn't try to delete it, I don't know if I should have or even if Avast was right.
The PC was already slow when I first got it. I ran Malwarebytes before and it found a trojan.agent that was apparently deleted. I also ran JRT that found bad things too (tell me if you need the log).
When I run in Safe mode, the PC seems OK, more responsive.
 
Anyone to help me?
 
Thank you.

A:PC slow in normal mode, OK in safe mode, Catchme rootkit detected by Avast?

Hi,
 
I turned PC on this morning, it was still very slow to start, but the Avast message about the rootkit didn't come up this time! PC was still slow to respond though.
I decided to run AdwCleaner (saved on to USB key from my laptop and copied then on to the PC) just to see and it found 9 "bad" registry keys. I cleaned them and restarted the PC as prompted. PC seems a bit faster to repond now. I also ran Malwarebytes (quick scan) which didn't find anything.
Still think something is not right, can somebody help me check for rootkit or anything else please? Thank you

Read other 32 answers
RELEVANCY SCORE 99.2

Hi,

I got win 7 home premium 64 bit on an i3 laptop. My system worked fine until today morning.

The problem is this;
When I boot the system in normal mode, I get to the part where I need to enter my password to login. Once i do that, all I get is a black screen with the mouse pointer that moves about normally. I've waited for the normal desktop environment to appear (ie icons and taskbar) but this doesn't happen (btw, my desktop background color is always black).
The system boots perfectly in safe mode.

Yesterday was the first time in over a year I used utorrent. I used to get the BSOD when I used to use it. I couldn't rectify the problem and hence had stopped using it. It worked fine yesterday though.

Any idea whats happening and how I could fix the problem?

A:Windows doesn't login properly in normal mode but fine in safe mode

I've tried running SFC /SCANNOW a couple of times but I keep getting a message that there may be corrupted files. I also created the sfcdetails.txt file.
Going to try the system restore option now

Read other 6 answers
RELEVANCY SCORE 99.2

Hello,

I have a Satellite Pro C850 1KU running Windows 7 Enterprise. When it is started in normal mode, it will load until the login page, then just reboot about 20 seconds afterwards. Over and over. The computer runs fine in Safe Mode. I have tried many different things, the recovery tools all say that the Windows installation is fine, the hard drive is in good shape and rather cool (41 C). I have tried all possible power setting combinations, have disabled all CPUs but one, stopped all programs and services in msconfig, ...

Having looke through various forums, I noticed that a frequent problem with Toshiba Satellite laptops seems to be the NEC/TOKIN capacitor on the mainboard. It dies after some time and seems to cause just the problems that I observe. There are many videos (search youtube satellite+toshiba+nec+tokin) and forum entries which describe the problem quite accurately (e.g. thread 8991 on badcaps dot net)

So before I disassemble my laptop, I have a few questions which hopefully someone has an answer to:
- Is there also a NEC/TOKIN capacitor on the mainboard of the Satellite Pro C850 1KU and could this cause the problems I have?
- Would it be in principle possible to just exchange the complete mainboard without having to reinstall Windows? Which mainboards would work, any of the C850 series (e.g. with 2.6 instead of 2.3 GHz)?

Thank you very much and best regards.

Read other answers
RELEVANCY SCORE 99.2

Hello, I'm hoping someone would be able to help me resolve this so that I can avoid having to reinstall Windows. Here's the situation: my laptop suddenly cannot boot up anymore; it usually hangs when the "Please wait..." dialog shows up with the text "Windows is starting up...", but sometimes it goes as far as the login prompt, then hangs after I enter my credentials and press Enter. When it hangs I cannot even move my mouse cursor. I can only think of two things I did out of the ordinary that created this mess:
I installed the driver for the Turtle Beach AudioAdvantage Micro USB stick audio card before my PC started hanging. However, after I installed the driver I was forced to reboot, and my computer rebooted just fine.
I closed my laptop's lid to put it in sleep mode while MyDefrag (formerly JkDefrag) was running. I have done this in the past without any issues, but this time when I exited sleep mode my computer was hanging, so I forced a reboot. This trouble started after I rebooted.

I am able to boot up in Safe Mode, but not Safe Mode with Networking, which leads me to think that maybe some network related drivers got corrupted. Some more info on my setup:
I have Windows XP Pro SP3 installed (v5.1.2600)
I have Avira AntiVir and Comodo Firewall installed
I am not using Hibernation
Audio: SigmaTel STAC9751
Graphics: Intel 945 GMS
Chipset: Mobile Intel 945 GMS Express
Netcard: Realtek RTL8101L
Wifi: Intel PRO/wireless 3945

Update 1: ... Read more

Read other answers
RELEVANCY SCORE 99.2

Hi, All of a sudden a day before, my computer froze and when restarted it started exhibiting horrendous symptoms-1. windows logo appear,then2. blank screen and no cursor login etc nothing display just sits thereAfter that, I tried to do startup repair but failed.Coming over to Safe Mode it is working fine.I also tried bunch of repairs from there still nothingused the clean boot from msconfig to see if any software causing issue or conflicts and did a system restore, still nothing.checked device manager and there is no exclamation point either that may depict hardware failure.My recent activity-installed "Advanced System care 9" 2 days back but have now removed using safe mode.1 more point it has been a month since my primary HDD is showing SMART error.but if safe mode is working can't we get normal mode backup and running.Please help me out of this conundrum, Any help would be sincerely appreciated.possible options I have in my mind-1.get new HDD and reinstall os2.format existing HDD and install fresh copy but doubt if this issue might returnreadily looking out for other options and would prefer rectifying old one first so that I can avoid a long tedious process of reinstalling everything from scratch.Sincere thanks to any responses.

Read other answers
RELEVANCY SCORE 99.2

After upgrading to SP2 about a month ago so I could take finals on my computer at school, i noticed that my computer wouldn't boot up in safe mode (i just get a blank dark screen and i can hear the computer doing something but giving it a reasonable amount of time it doesn't progress from that screen). It didn't concern me because normal mode was working and i was able to take my tests. But now I want to get to the bottom of this. I delayed getting sp2 because i had a feeling it would mess up my computer. (i've had other problems too with visual skins but i was able to resolve those).If it matters, i ran a scan of my system with spyware doctor and it said i had a trojan.dialer and needed to boot in safemode to get rid of it. When I tried, it wouldn't load. Oh, btw, any way to get rid of that trojan.dialer without using safemode?

A:Windows Xp Home, After Sp2, Safe Mode Doesn't Work, Normal Mode's Fine?

Try running Ewido online scan and post the results overhere.

Read other 6 answers
RELEVANCY SCORE 99.2

I am running using Dell Inspiron with windows vista. A couple days ago, I got on the computer and then it froze, at fist the program I was using froze, and then I got a circle next to the arrow, but could still move the arrow, then the arrow stops moving. CTL ALT DEL does not work, so i must do a hard reboot, try to boot in safe mode and all the files come up but then it goes no where and the computer either restarts or I reboot it.

I have run all types of tests and nothing comes up. Today I got the blue screen of death twice, but after reboot, it goes away. I do not have a Boot Disk and have tried all the tests in the F8 command. Currently I am running an expanded memory test, but figured I would get this out there before I go insane.

Any ideas would be MUCH appreciated.
 

Read other answers
RELEVANCY SCORE 99.2

There is no malicious software.I have gone through Malwarebytes,TDSSKiller,Kaspersky,etc.Nothing was found.
It doesn't entirely freeze.I can move the cursor which usually is a blue circle.Sometimes more things like highlight icons w/ the cursor or the clock keeps going.
Sometimes when I press ctrl+alt+del and open task manager,the programs that didn't open when I clicked on them will open up.Most times pressing ctrl+alt+del does nothing though.
It works fine in Safe Mode and Safe Mode with Networking.I have disabled all start ups and every service except Microsoft ones and restarted in Normal mode.Still the same problem.
I used checkdisk and it said nothing is wrong.
There are random times where it works fine.No specific time of day.It just happens.Most times it is this way though.

A:Laptop only works in safe mode.Hangs w/ blue circle in Normal mode.

Did you disable the startup items and services in Safe Mode, and then restart in normal mode?
 
Essentially what you are trying to do is a Clean Boot, this has to be performed in normal mode.
 
 
 
***This is a diagnotic tool for Windows Vista, Windows 7, and Windows 8.  This will not repair your computer, but it may point to where the problem lies so that a repair can be made.***
 
Warning:  Disabling items in Services or Startup may leave your anitivius disabled until the process is ended.  For this reason I would suggest that you perform this process off line.
 
Step 1
 
(1)  Click on the Start orb , then type msconfig.exe in the Search programs and files box.  
 
(2)  When msconfig is seen in the pane above the search box and under Programs, right click on it, then click on Run as administrator.
 

 
If you are prompted for an administrator password or for confirmation, you should enter the password or provide confirmation. 
 
Step 2
 
(1)  Click on the General tab.   
 
(2)  Click the Selective startup option. 
 
(3)  Remove the check mark in the Load startup items  check box. 
 

 
Step 3
 
(1)  Click on the Services tab. 
 
(2)  Place a check mark in the Hide all Microsoft services check box, this will remove the Microsoft Services from the list but will still be running. 
 
(3) ... Read more

Read other 18 answers
RELEVANCY SCORE 99.2

My Toshiba satellite will only boot in safe mode tried sfc/scannow getting this message

Windows resource protection found corrupt files but was unable to fix some of them.

I've tried a system restore but that wasnt very successful either, if I uploaded the CBS log of the scan could someone try help me with the problem. Thanks

A:BSOD when trying to boot in normal mode, safe mode works fine

You may need to run SFC up to 3 times for it to have a chance to repair all files.

If it won't then you can consider a Repair Install.

However be aware that factory preinstalled Win7 is one of the worst possible installs of Win7 one can have, larded with bloatware and duplicate utilties that intefere with better versions built into Win7. So I would strongly consider doing the vastly superior Clean Reinstall - Factory OEM Windows 7.

If you decide to try to repair you can also capture the BSOD file and post it up for one of our BSOD analysts as shown here: Blue Screen of Death (BSOD) Posting Instructions - Windows 7 Forums

Read other 3 answers
RELEVANCY SCORE 99.2

Windows only opens in safe mode,tried reloading drivers, last known good configuration,etc. When in normal mode black screen only, when acessing task manager shows all processes stopped and will not allow me to start them.

A:Black screen when start in normal mode, works in safe mode only.

Hello CliffordJ. Microsoft Security Essentials is installed, correct? Many MSE users running Vista (but not all) suffered black screen after login following installation of Update for Microsoft Security Essentials - 4.9.218.0 (KB3140527), released about a month ago. In fact there is already a thread here: http://www.bleepingcomputer.com/forums/t/606422/windows-vista-x64-bksod-after-login-or-no-access-in-normal-mode-suspect-mse/. The posters there disabled MSE 4.9 in Safe Mode by unticking a brand-new setting in the UI (Administrator > Turn on this app). Another method of escaping this situation would be to restore your system to a point before the update was installed, then hide the update in Windows Update. That would allow you to resume using MSE 4.8 if you wish.

Read other 10 answers
RELEVANCY SCORE 99.2

Hi there, I'm trying to fix my Aunt's windows XP computer. I downloaded MBAM as she had previously mentioned getting a call on the phone from someone in India telling her she needed to pay $160 for her antivirus or her computer would shut down.

I ran MBAM and it took about 8 hours to scan, and at the very end found a bunch of results. I told it to get rid of them, and then restarted. Upon restarting, it also ran a disk check, and after that finished, it booted up but took forever to load. Upon loading the taskbar showed up for a brief moment, then disappeared, and I can't seem to get it to run from the task manager either. It brings up the explorer.exe process briefly, then without ever loading the taskbar, it ends the process.

I got a bit worried at this point and tried to restart in safe mode. However, when I do that, it loads a bunch of drivers and then stops. It never finishes loading. (this happens in safe mode with and without networking)

I also tried restarting back into normal mode and running avast through command prompts, but it doesn't do anything and I also got errors stating that a particular file is missing.

What should I do next? I was going to attempt running combofix from my flash drive, but when I try to CD into the drive, it says the drive isn't ready. If you have any suggestions on what to do, let me know, thanks.

A:Unable to boot in safe mode, explorer.exe not loading in normal mode

Do not run combofix,let me ask someone to help you

good luck

Read other 2 answers
RELEVANCY SCORE 99.2

Hey guys I've checked through some of the tuts and what-not on this forum and still can't find a way to get me out of trouble..
i turned my computer on yesterday (23rd September) and there was an automatic update. Ever since the update my computer has been extremely slow (will take several minutes to open firefox -or anything for that matter). I booted safe mode and it's running fine. I opened up msconfig and did a clean boot but the problem was still there.
It's a fairly new build and I was stupid and forgot to get a virus protection i can't install it in safe mode either..

Can anyone help?
-cheers

A:Explorer running slow in normal mode, fine in safe mode.?

Windows Defender Offline

Read other 9 answers
RELEVANCY SCORE 99.2

Hello everyone.  I am trying to fix my mom's computer but have so far been unable.  The laptop is running but it is incredibly slow.  When I first got on it a bunch of pop ops took over the screen.  The computer would randomly go to other sites on it's own.  It would go to a search sight called "clarosearch".  Worst of all, it's incredibly slow.  For example, from the desktop, it take about 45 seconds for the IE window to open when I click on the icon.  It takes about that long to navigate to a page and so fourth. I downloaded and ran a registry cleaner, spybot search and destroy, malwarebytes, and ad-aware.  These found a bunch of problems and cleaned some up, I guess.  The pop ups are gond and so is the strange search site, but the computer is still running just as slow.  It's a paperweight.  Getting another computer isn't really an option right now as my mom is unemployed and we're actually trying to get her resume online but we can't even do that right now with the way the laptop is acting.  I downloaded hijackthis and ran a scan.  Here is the log.    Oh, and as the subject says, the computer runs fast and fine in safe mode.  Please let me know if there is any other info that is needed as I'm not sure what to provide.  Thank you in advance for any help or suggestions you can provide.  Logfile of Trend Micro HijackThis v2.0.4Scan saved at 6:26:57 PM, on 4/26/2014Pl... Read more

A:Windows XP Laptop very slow in normal mode but fine in safe mode

Hello scoobyjax,my name is Jo and I will help you with your computer problems.Please follow these guidelines:Logs can take a while to research, so please be patient.Read and follow the instructions in the sequence they are posted.print or copy & save instructions.back up all your private data / important files on another (external) drive before using our tools.Do not install / uninstall any applications, unless otherwise instructed.Use only that tools you have been instructed to use.Copy and Paste the log files inside your post, unless otherwise instructed.Ask for clarification, if you have any questions. Stay with this topic til you get the all clean post.My first language is not english. So please do not use slang or idioms. It could be hard for me to read. Thanks for your understanding.***1. Download Security Check by screen317 from here or here.Save it to your Desktop.Double click SecurityCheck.exe and follow the onscreen instructions inside of the black box.Vista / Windows 7/8 users right-click and select Run As Administrator.A Notepad document should open automatically called checkup.txt; please post the contents of that document.***2. Download OTL to your desktop.Double click on the icon to run it.Vista / Windows 7/8 users right-click and select Run As Administrator.Make sure all other windows are closed and to let it run uninterrupted.When the window appears, underneath Output at the top change it to Minimal Output.Check the boxes beside LOP Check and Purity Check... Read more

Read other 3 answers
RELEVANCY SCORE 99.2

Not sure what I have stumbled upon here. Was trying to download some music from SugarSync that I had from another PC, realized I did not have a music player installed and tried to download VLC and that's when things went bad.
 
I had run my Anti-Virus (Avast ) and it found nothing,
I just now opened it (in safe mode) to obtain the official name/version and found it to display a large red banner declaring I am unprotected and the Avast service turned off.
None of those controls on that panel work 
 
Am assuming some infection did this as I did not turn it off!
When I clicked Scan it displays "Unable to start scan. There are no more endpoints available from the endpoint mapper"
 
This is an Asus G73JW Laptop
Windows 7 SP1
I use
Avast Internet Security
Spybot S&D
CCleaner
 
Any Idea as to what I have run into here?
 
Thanks,
 
 
 

A:Fine in Safe mode, but in normal mode, icons and Startmenu don't work

Have you performed a System Restore recently?
 
Download your version of Avast, but don't install it yet.
 
With the computer offline use the Avast uninstall utility to uninstall your current installation.
 
Once you have uninstalled the old version, install the version you downloaded.

Read other 2 answers
RELEVANCY SCORE 99.2

Hi i really need some help. I got a virus notification from mcaffee saying i have trojandownloader:win32/renos.dz and i selected remove and thought it would be fine. But the next day the computer kept restarting and ie and mozilla would not open. They only opened in safe mode with netoworking so i tried to download virus protection but when i tried to install it the computer would restart so i renamed the programs which it worked for so i could install it. I installed malware and it got rid of some files but it has not solved the issue. Also when in safe mode and using the internet the page always redirects to other pages like smartbizsearch and the internet just does not function properly. I downloaded HiJackThis from safe mode and renamed it so i could use it. I downloaded dds as instructed and here my log for it:DDS (Ver_09-05-14.01) - NTFSx86 NETWORK Run by Himesh at 16:00:46.10 on 03/06/2009Internet Explorer: 7.0.6001.18000Microsoft? Windows Vista? Home Basic 6.0.6001.1.1252.44.1033.18.3000.2377 [GMT 1:00]SP: Windows Defender *enabled* (Updated) {D68DDC3A-831F-4FAE-9E44-DA132C1ACF46}============== Running Processes ===============C:\Windows\system32\wininit.exeC:\Windows\system32\lsm.exeC:\Windows\system32\svchost.exe -k DcomLaunchC:\Windows\system32\svchost.exe -k rpcssC:\Windows\System32\svchost.exe -k secsvcsC:\Windows\System32\svchost.exe -k LocalServiceNetworkRestrictedC: ... Read more

A:Cannot open IE or Mozilla in normal mode has to be in Safe Mode and computer keeps restarting

The logs from before were done in safe mode these are the ones from normal mode.DDS log:DDS (Ver_09-05-14.01) - NTFSx86 Run by Himesh at 16:27:33.45 on 04/06/2009Internet Explorer: 7.0.6001.18000Microsoft? Windows Vista? Home Basic 6.0.6001.1.1252.44.1033.18.3000.1826 [GMT 1:00]SP: Spybot - Search and Destroy *disabled* (Outdated) {ED588FAF-1B8F-43B4-ACA8-8E3C85DADBE9}SP: Windows Defender *enabled* (Updated) {D68DDC3A-831F-4FAE-9E44-DA132C1ACF46}============== Running Processes ===============C:\Windows\system32\wininit.exeC:\Windows\system32\lsm.exeC:\Windows\system32\svchost.exe -k DcomLaunchC:\Windows\system32\svchost.exe -k rpcssC:\Windows\system32\svchost.exe -k LocalServiceC:\Windows\System32\svchost.exe -k NetworkServiceC:\Windows\System32\svchost.exe -k secsvcsC:\Windows\System32\svchost.exe -k LocalServiceNetworkRestrictedC:\Windows\System32\svchost.exe -k LocalSystemNetworkRestrictedC:\Windows\system32\svchost.exe -k netsvcsC:\Windows\system32\SLsvc.exeC:\Windows\System32\spoolsv.exeC:\Windows\system32\svchost.exe -k LocalServiceNoNetworkC:\Windows\system32\agrsmsvc.exeC:\Program Files\Common Files\Apple\Mobile Device Support\bin\AppleMobileDeviceService.exeC:\Program Files\Bonjour\mDNSResponder.exeC:\Progra... Read more

Read other 3 answers
RELEVANCY SCORE 99.2

Win 7 Normal Mode won't start, will go past Starting up Screen and just hit a Black screen and will hit a Crash Dump (blue error screen)..... I can boot into safe mode fine and I have fun CHKSDK and after a reboot it fixed a few problems but I hit the same Crash Dump Screen. I have also made sure my whole pc is all clean and connected, no corroding parts etc etc, made sure my pci-e slot is default etc etc, no luck at all...

Its a new installation and worked fine last night and early this morning after separate boots. But as soon as I booted this afternoon it wouldn't load and would hit the blue error crash dump screen....

So any suggestions?

Just last night My main HDD died also which is why I had to use my secondary HDD as my main....

=\

A:Win7 Normal Mode wont boot, Safe Mode works though... Help?

1) When you "ran checkdisk" dis you run it with the "/r" switch? If not, please run chkdsk /r now.2) Download BlueScreenView:http://www.nirsoft.net/utils/blue_screen_view.htmlunzip downloaded file and double click on BlueScreenView.exe to run the program.when scanning is done, go to EDIT - Select AllGo to FILE - SAVE Selected Items, and save the report as BSOD.txtOpen BSOD.txt in Notepad, copy all of the content, and paste it into your next reply

Read other 5 answers
RELEVANCY SCORE 99.2

My speedtest.net performance is 30 Mbps download, and between 0.3 and 2.0 Mbps upload. If I start in safe mode with netorking, I get download and upload speeds of 25-30, my contracted speeds. Obviously, something loading in the full mode interferes with upload speed. I have tried restarting in safe mode with all of the items checked in the services and programs tabs in msconfig, and still get excellent up and download speeds. How can I figure out what is interfering with my upload speed in normal mode, but not in safe mode?

A:Poor upload speed in normal mode, fine in safe mode

Use msconfig to determine what is causing the problem

How to use msconfig in Windows 7

Click on Start then Run, type msconfig and press Enter.
Click on the Startup tab, record what is currently starting then click the Disable All button.
Reboot and see if it runs better.
If yes then use msconfig to enable several items at a time till you find the culprit.

If no, start msconfig and click on the Services tab.
Check the Hide All Microsoft Services box, record what is currently starting then click the Disable All button.
Again, do a regular boot, see if it runs normal.
If yes then use msconfig to enable services till you find the culprit.

Once you've found the culprit, uninstall it or find out how to eliminate it from your system. Simply disabling it in msconfig is a temporary fix at best.
Enable everything else you disabled.

Read other 6 answers
RELEVANCY SCORE 99.2

Lenovo Laptop

Windows starts normally, but after login displays a black screen with only cursor showing. Mouse is okay, ctrl-alt-del opens a window and task manager works okay.

Safe mode with networking works normally.

Restored from to a restore point prior to an install of "proformax Cleaner", no change to behavior.

Used task manager to take note of services running in safe mode.

Restarted in normal mode and used task manager to stop all services not running in Safe Mode.
Stopping the "Group Policy Client" caused the desktop to reappear. However on restart in Normal mode the "Group Policy Client" had the service's stop etc choices greyed out.

Running MSconfig to eliminate all startup programs and most services, the "Group Policy Client" choice rechecks the box when "Apply" is clicked.

My guess is that a virus changed a registry entry to prevent the desktop from being displayed. Any suggestions as to how to proceed would certainly be appreciated at this point.

A:Win7 Prof no desktop or icons in normal mode; safe mode okay

Hello WWilliam50 and welcome to Seven Forums.

Have you run a full scan with your installed anti-virus of choice? Even if you AV comes back "no malware found" it wouldn't hurt to run some additional free on-demand scanners. (No AV product is 100% effective 100% of the time.) Some of the free software recommended by Forum members include: Malwarebytes; SuperAntispyware; and ESET Online Scanner.



   Warning
Make sure you don't install unwanted/unneeded crapware. Some sites are now bundling extra "stuff" with the main product. Uncheck any boxes for things you don't want.
Once you've completed all scans, see if you can rebuild your icon cache.

Icon Cache - Rebuild

If still no joy see if you have any damaged or corrupt system files by running a System File Checker scan from an elevated command prompt (option two.)

SFC /SCANNOW Command - System File Checker

Read other 5 answers