Over 1 million tech questions and answers.

Installing ssd inside Hp Omni allinone

Q: Installing ssd inside Hp Omni allinone

I am considering removing the 1tb Hitachi hard drive inside my Hp Omni allinone computer and replacing it with a solid state drive, but there's a few things I'm uncertain about. First off, I don't know if the Hitachi hard drive inside my system is the standard 3.5 size. Here are the models in my price range that I am considering... Mushkin MKNSSDRE1TB Reactor 1TB 6Gb SATA III 2.5inch SSDSanDisk Ultra II 960GB SATA III 2.5-Inch 7mm Height Solid State Drive (SSD) with Read Up To 550MB/s-...Samsung 850 EVO 1TB 2.5-Inch SATA III Internal SSD (MZ-75E1T0B/AM)Crucial MX300 1TB SATA 2.5 Inch Internal Solid State Drive - CT1050MX300SSD1 So, they all appear to be similiar, which brings me to my next question. I'm thinking the hard drive in my all in one may be mounted inside there differently than what is standard, then if so, are there mounting brackets that will fasten down, hold the new drive in place properly, and still enough space for the back panel to snap down? Then my last concern before I purchase anything is the resulting performance of installing the ssd. Since I still have the AMD E-450 processor that runs at a measly 1.6 Ghz. From my understanding, because the way these allinones are built, there isn't any options for processor/motherboard, or at least none I know of that would be considered an upgrade. So, with the same processor/motherboard in there, would there be enough performance improvement to justify the time, cost and effort in doing so? Or would I be better off running it as it is until it breaks, and building a pc that has the i7, ssd, msi or gigabyte motherboard, and other features I yearn for?

Read other answers
Preferred Solution: Installing ssd inside Hp Omni allinone

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)


I am using HP Omni 120-1115in all in 1 pc. I m a bit of a gamer and i want to play some nyz games like BF4 AC4 etc Bt i cant. I need a solution to play good graphics games in my pc. what shoul i do ? can i use a external graphics card or something ? i gt 4gb ram and amd radeon hd graphics. theres less games i can play now in my pc. plz tell me a soluion 

Read other answers

When i try to turn off my HP AllInOne T4R07EA by Start, Turn Off System, the PC don't turn off and show the change user screen. I already check the power saving option and it's all correctly selected, someone know if there're othe option that manage this function? 

Read other answers

Hi all,

I have an Acer 5551 that I want to restore to factory. The alt F10 doesn't work at boot, so I need to find another way.

Is there a way to reinstall the preinstalled OS without using the eRecovery shortcut? Maybe something in Windows? Command prompt?

Any help would be appreciated.


A:Installing OEM inside Windows

Did you make the Recovery Disks?
Manual how to use Acer eRecovery Management here:

Read other 9 answers

I have an averatec all in one computer that is about 5 years old. when i try to load the OS on the machine it give me a error message after nearly completing the installation. I was told by Microsoft that something was wrong with the computer but the person I was talking to did not speak very good English. I hope that you can help me.

A:can't load windows8 on Averatec allinone

Read other 9 answers

First thanks for the 5 step process. I hope I am doing this right! My HP F335 All-in-One Deskjet Printer shows errors and a constant need to reinstall SW whenevr I push the scan button or from the Control Panel. The window asks for a source 1 (I guess the OEM install CD) and wants to find "aiosw.msi" which is NO where on the CD or my PC. Cancelling out of that just starts it again until about 5 times of cancelling - then the printer tries to scan but does not complete, shuts down, and shows an "E" on the control screen. In an earlier thread you advised that "aiosw.msi" was suspect. I would appreciate any help you can provide. I am attaching the various logs (hopefully correctly) Thanks!
Deckard's System Scanner v20070611.50
Run by Pat on 2007-06-27 at 20:18:11
Computer is in Normal Mode.

-- System Restore --------------------------------------------------------------

Successfully created a Deckard's System Scanner Restore Point.

-- Last 5 Restore Point(s) --
20: 2007-06-28 01:18:16 UTC - RP742 - Deckard's System Scanner Restore Point
19: 2007-06-28 01:08:47 UTC - RP741 - Software Distribution Service 3.0
18: 2007-06-28 00:59:39 UTC - RP740 - System Checkpoint
17: 2007-06-26 21:16:47 UTC - RP739 - Removed HP Photosmart Essential
16: 2007-06-26 16:07:39 UTC - RP738 - Installed Windows XP KB926239.

-- First Restore Point --
1: 2007-06-22 19:40... Read more

Read other answers

Worked fine for 18 months. Suddenly 'cartidge not recognized or found' is what I get. I use refilled cartidges, latest are both new (3rd usage since refill) and never had problems before. Cleaned cartridges, no improvement.

Is it worth bothering to try and get the problem fixed ; or should I just buy another (60 on special at PCW)


A:Allinone Printer, HP C4380 Photosmart

Read other 8 answers

Link to product:http://store.hp.com/UKStore/Merch/Product.aspx?id=P1K28EA&opt=ABU&sel=DTP I bought this PC on April 25 2016 and up till now this is the worst PC I have owned in my life!I made 3-4 reviews about this garbage and its still not on the UK website!I dont know if its either the terrible hardware or mine is just a faulty PC. Issues: 1.My USB ports usually stop working (when I connect a peripheral) 2.Not a issue just a stupid thing HP did the HDMI is a output which means I cant hook it up to an output! 3.My PC often just freezes or lags 4.You might say "Your PC is stuffed with viruses" Its not only 6gb of storage was used and the only things I have installed was autodesk and google sketchup and steam and remote play and Unity. I did LOTS of anti virus scans using McAfee and AVG and there was nothing I uninstalled steam and everything else and there was no difference my PC was extremely slow. 5.I have a feeling my ram is not working properly; I have 4gb ram but 3gb usable but my PC usually stops when opening microsoft edge it just stops working and lags. 6.when leaving an application on for a while and returning back to it it just tells me 'Not Responding' Everytime! 7.Dissconectivty issues: I always disconnect from the internet when my wifi is working. No my wifi is fast so it should work I checked my other device and it showed my wifi is working this issue also applies to my HP all in one printer which always has a... Read more

A:My AllinOne is new and its extremely slow and has lots of is...

Did you get this as a gift?  Here are the specs.  With a lowly 1.8 Ghz processor (soldered) and a graphics set that is part of the CPU chip, and here is NO slot for a graphic card.  No possible ungrade except a increasing the RAM to two 8 GB modules.  It has a laptop brick for a power supply. What you have is a basic inetrnet/email unit. IMHO, it was never meant to be what your expecting.   I then thought you were pranking, but your a Brit, so I stopped short.

Read other 3 answers

In the middle of me working the pc goes black and then after a few seconds returns. I am concerned that 1- I do not loose my data2- pc does not crash3- i need to work and this is delaying me  Does this mean pc is bad? Support wanted to do bios updateand other things and then reset pc. I do not have time for guessing games or experimenting on my time as this is a business use computer. Can any one help. Less than 2 months old.   

Read other answers

Ok well I'm having trouble finding the 98se cd used on my old computer (I need to reinstall it), and I was thinking after a recent small memory upgrade XP might be able to run slightly better. PIII 500-700mhz (can't remember I would check cpu-z on it but the computer has been rendered unbootable). 384mb of SDRAM. The requirements I found were:255mhz, 64mb from Paul Thurroits site.

Ok well I have a reinstallation cd which seems to function as almost a normal xp cd (doesn't have the repair option). Well I need to have the setup run off the cd drive on my 98 but I'm not sure how to get into the bios so I can run the cd-rom before drive A: So what I'm asking is how to how to install xp to my second hard drive. Then I would be able to get all my nessecery files off my other hard drive (the one with the 98)

A:Installing XP to an old computer-look inside for specs.

If you boot from the XP CD, you will be given the option to install it wherever you want.

If you have the floppy set as your first boot device and CD second, and there is nothing in your floppy drive, it will boot from the CD.

Read other 3 answers

Hello, I recently got a friend to install a motherboard to me, but I've been having some problems with the computer, and after looking at pictures of installed motherboards I can see that almost all cables are connected to the motherboard, however, only 3-4 are connected on mine, and maybe 6-7 loose in the computer.

Here's some pictures of the computer inside.

http://data.fuskbugg.se/skalman01/datorbilder 001.jpg

http://data.fuskbugg.se/skalman01/datorbilder 002.jpg

http://data.fuskbugg.se/skalman01/datorbilder 003.jpg

http://data.fuskbugg.se/skalman01/datorbilder 004.jpg

http://data.fuskbugg.se/skalman01/datorbilder 005.jpg

As you can see there's atleast 4 cables from the harddrive that isn't connected, and 2-3 from the PSU.

Now if anyone could help me, It'd be highly appreciated!

A:Installing a motherboard? (Pictures inside.)

Read other 13 answers

Hi there all, I have a Lenovo A740 AllInOne and until yesterday all was fine (the buttons was working) Today I just want to use the HDMI Input in order to see another laptop displayand if I toutch the monitor button in order to change the HDMI Input ...is not work.  Is really strange cause no one is work ...there is 7 butons (volume, contrast etc...) All the butons on the right side down of monitor is blocked.  Can anyone help me please Thanks in advance Denis

Read other answers

Hello, I need to know if my HP All in One Envy 20 d003la is compatible with an SSD.Now I have a 3.5in HDD but I want to upgrade to SSD.Thanks!

A:Install SSD on a HP Envy 20in d003la allinone

Hi, 3.5" SSD is very rare or may not exist. You need one of the following brackets:      http://www.newegg.com/SSD-HDD-Accessories/SubCategory/ID-43 Please check axisting shape/angles and but a right one. Regards.

Read other 1 answers

The machine is not mine, so I only now that it has Windows 8.1 with Bing, Office 2013, and SQL Server Express 2008 R2 used by an accounting application known as CONTPAQi in Mexico.

The error only happened once 2 weeks ago, but I'm being asked to be thorough.

This is the WinDBG analysis on the dump:

Microsoft (R) Windows Debugger Version 6.12.0002.633 AMD64Copyright (c) Microsoft Corporation. All rights reserved.

Loading Dump File [C:\Users\Sistemas PC\Documents\Compartido\Sistemas\Informacion de Equipos\Facturacion Lenovo C260 All-In-One\012716-26890-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available
Symbol search path is: srv*c:\Symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 7 Kernel Version 9600 MP (2 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS Personal
Built by: 9600.18185.amd64fre.winblue_ltsb.151230-0600
Machine Name:
Kernel base = 0xfffff802`1248e000 PsLoadedModuleList = 0xfffff802`12761630
Debug session time: Wed Jan 27 16:32:56.422 2016 (UTC - 8:00)
System Uptime: 4 days 7:08:50.557
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
* ... Read more

Read other answers

Can't dual-boot installing inside Win7 ...

I have a second hd in my machine, when I attempt to install to that drive running a mounted iso from inside Win7 I don't get the options to where to install. It asks me what I want to keep, as if it is going to upgrade my os. I don't want that, I want to dual boot. Any clues anyone?

Thanks in advance.

A:Can't dual-boot installing inside Win7

Burn a DVD from the .iso and try with that. But if you have 2 HDDs, I would disconnect the other HDD during the install and change the BIOS boot order for OS selection. Is a faster boot.

Read other 7 answers

Windows installation encounter an unexpected error, very that the installation sources are accessible and restart the installation...
Error Code 0xC0000005 .....

im installing this on my friends pc Spec are way over then what w7 needs and hase more then mine. idk why hese geting this error its soon as i click install from the cd. ANYONE know a fix for this?

A:Problem Installing Wodows 7 7624 Error Code Inside

Quote: Originally Posted by StonR

Windows installation encounter an unexpected error, very that the installation sources are accessible and restart the installation...
Error Code 0xC0000005 .....

im installing this on my friends pc Spec are way over then what w7 needs and hase more then mine. idk why hese geting this error its soon as i click install from the cd. ANYONE know a fix for this?

Looks like to me that you had either a bad DVD burn or you downloaded a bad image from a torrent...I will send you the correct link and you can do a hash recheck to make sure it is okay

Read other 7 answers

So first I get this message when I mouse over the speaker icon(notice the red "x" on the icon).

When I click the icon, Windows does a diagnostic and then this shows up.

This is whats listed in my playback devices and this is with "Show disabled devices" enabled. Everything is enabled

Here is a picture of what my device manager looks like.

I've tried installing drivers for my sound card and my chipset, I tried restarting my computer, updated from my device manager, uninstalled drivers, reinstalled, etc. I've been searching online for a bit and nothing I found worked so I figured I'd give this a shot. I tried uninstalling the service pack update but that didn't work.

Thanks for the help.

Tech Support Guy System Info Utility version
OS Version: Microsoft Windows 7 Ultimate, 32 bit
Processor: Intel(R) Core(TM)2 Quad CPU Q9300 @ 2.50GHz, x64 Family 6 Model 23 Stepping 7
Processor Count: 4
RAM: 3198 Mb
Graphics Card: NVIDIA GeForce GTX 460, 1024 Mb
Hard Drives: C: Total - 953766 MB, Free - 300816 MB;
Motherboard: Gateway, G33M05G1

A:Sound not working after installing windows updates(pictures of errors inside)

Read other 8 answers

Okay i have spyware doctor and it just detected a file called allinone and i pressed the delete key to get rid of it right but it dident go away and im confused because i tried to delete the file in safe mode then i tried to run spyware doctor at the startup screen and it still wont go away the file is log.dll and its in my system32 folder i just dont know how to get rid of it and it seems its been on here since last year so im in **** so can some one here help me out please!!!!

A:Solved: I have "allinone" spyware/keylogger/recorder and i need help to delete it

Read other 6 answers

Hello, We have gone to the website
and download the file to open Inside of IE. Once the file is open, none of the links either e-mail or web site works. However, if we open the same file Inside of Google Chrome, the links work. So, we want to know if we are missing something in IE or a plugin.
The PDF file opens with no problem but the links are not enabled. The file works in an Apple Machine and Google Chrome. However, if we download the file physically inside of the computer and then open the file with Adobe Reader, the links all work! Any ideas
how to solve this issue? Thanks Miguel Moreno

Miguel A. Moreno Alfa Logos inc. Tel. 514-253-2548


Internet Options>Security tab, click "Reset all zones to default" (there's a setting for scripting of ActiveX controls)
Start>Adobe Reader>Edit Preferences>there are setting for how embedded links are handled.
Chromium uses its own pdf reader plugin.Rob^_^

Read other 3 answers

Not sure if this is the correct catogory to post my question in, but here goes. I have a HP Omni 100, about 6 yrs old. About a month ago, I went to the restore function & my computer crashed. Now, all I keep getting on my screen, after the initial start up is select keyboard function, or something of that nature. I hope I have not lost everything I have in that computer, since I have pics I cannot replace. Two or three months ago, it started to act funny. The page I was on would turn into a smaller square in the middle of the screen, and that square would be full of multi colored lines.(Like snow on a tv screen) Now I cannot get it to do anything but show the keyboard page????? Please advise as to what I could or should do. THANK YOU Roger

Read other answers

Hi,My pc monitor suddenly just stop working. But there isnt any port available to connect to another monitor. All my work is this pc and i need to extract them, is there anyways to do it? Also is it advisable to get it repair?

Read other answers

I have a all in one HP OMNI 200 pc. The computer came with windows 7 but was upgraded to windows 10 about 6 months ago.   Was trying to do a recovery/reset and it froze up with the following message:RecoveryYour PC /device needs to be repaired.  The operating system couldn't be loaded because the kernal is missing or contains errors.File:/windows/system32/ntoskrnl.exeerror code 0xc0000221

Read other answers

I've been backing up "My Documents" with CDBurnerXP because

1. I consider Windows Backups to be opaque and I prefer to keep them simple and to know what is going on
2. Windows Backups does some things I believe are risky so I will not use it
3. Windows 7 had a deep directory structure problem and I presume Windows 8 continues to
4. It's ridiculous to backup "Windows" when I really only care about the safety of my data and since I am a slow typist who can't type at 3 Gigahertz it seems unlikely that I will ever have produced enough data that won't fit in one piece of optical media
5. I prefer to use a backup medium that has no moving parts and no firmware and humidity and mechanical shock resistant and contains no software and nothing vendor specific and blank DVDs are one such medium
6. I don't understand how a "backup DVD" can get scratched if there are never children and animals in the building (movie DVDs are a different matter)

Unfortunately, I can't continue down this route because my Windows 8 is now inside VirtualBox and I can't seem to make CDBurnerXP and Windows 8 recognize a blank DVD as a suitable target for a backup.

I am looking for suggestions for DVD burning software that is free and is known through your personal experience to work inside VirtualBox.

A:can I burn a DVD from inside Windows 8 inside VirtualBox

I can't comment on VirtualBox, but the most popular free burning program is Imgburn. Although I have Nero burning software, I find the Imgburn to be easier to use for iso CD's and DVD's.

The Official ImgBurn Website

I also use Macrium for backing up my PC's, but I back up to separate hard drives, not DVD media. There is a free version of Macrium.

Macrium Reflect FREE Edition - Information and download

Read other 3 answers

Can I install windows 7 ultimate inside the same(key code) windows 7 ultimate by using Virtual Box or Virtual PC and activate both scents its the same PC(laptop in this case)?

Boot Straps

A:Installing Win7 inside of Win7-actvation

It is within the line that states a single cpu.... but i believe this is a question for a mod or MS

Read other 9 answers

Omni 100 all in one pc will not boot/power up.When I push the power button, I can hear the fan engage and spin but nothing comes up on the screen. The first time I tried to turn the computer on this morning,the little blue light on the lower right corner DID light up but nothng else happened. After watching/waiting for 10 minutes, i held my finger on the power button to turn the machine off, waited a few minutes, hit the button again. The second time, the fan started going but the blue light did NOT come on this time. I waited 5 minutes and nothing happened. This time, I just pulled the plugg out of the wall and waited 10 minutes, plugged it back in, hit the button, same thing,,,fan engaged, no blue light,,,fan just spinning/whirring but nothing comes up on the screen. I have another one of these computers and i switched power supplies and the power supply is fine.

Read other answers

I have some issues when I OCR with this software, specifically with PDFs, I get black outed boxes on the images, Any ideas? I can post examples if needed,

Read other answers

I just recently started having this problem, I would go away from the comp leaving it on sleep for about an hour come back and it would not let me open any programs, security options and even after several restore's and virus checks it still is giving me the problem, sometime it fixed itself but this time it has not. Any solution to do it other than a full wipe, The programs work in safe mode but other than that no other mode works

A:Problems with my Hp omni all in one pc

You can try a System Restore. If you aren't familiar with that process, you need to indicate which version of Windows you are using (XP, Vista, Windows 7) so we can direct you.

Read other 3 answers

I have an All in one desktop Omni 27 1001ed. Now I want to use my external HD 3TB but it only reconize 2TB. Can someone explain what to do to get the other 1TB also. I have already changed the disk to GPT and formatted it again. Still no result. 

Read other answers

Hello world!The problem is I have the HP Omni 27-1002er and have no idea how to add a second monitor to it.Where can I find video out port?Thank you!

A:HP Omni 27-1002er

Hi, It does not have out port for an external monitor:      http://support.hp.com/in-en/product/hp-omni-27-1000-desktop-pc-series/5186974/document/c03262527/ If you wish, please use USB to HDMI or USB to DVI adapter such as:       http://www.officeworks.com.au/shop/officeworks/p/comsol-usb-to-dvi-hdmi-vga-adaptor-cou2dhvad Regards.

Read other 1 answers

Hi, I have bought ALL IN ONE HP OMNI 120 PC from Singapore. Currently i am in india and am facing issue with the PC that it is not booting. When i checked with Local HP support they said, the motherboard needs to be replaced. However, the motherboard is not available anywhere and am stuck with the PC as i didnt find the replacement motherboard. Please let me know where i can get the motherboard for this PC and the cost of it ? Also, provide the warranty details of the motherboard. Also, i would like to know,whether it is advisable to replace the motherboard or buy a new PC?

A:want to buy All in One Omni 120 PC motherboard

Hi,Can you please provide the exact model of your Omni 120 PC for further help. Let me know,David

Read other 1 answers

I'd like to upgrade the RAM in my all in one and I'm finding conflicting answers on whether this can be done.  I currently have  8GB (2x 4GB DDR3 1333 SODIMM- 10600)I've got Windows 7 Home Premium 64 bit as my OS.Most of the specs for my computer list 8GB as the maximum amount of RAM possible, but another source on the HP website advises that it depends on the OS, and that with Windows 7 premium 64 bit, 16GB is the max.I don't want to purchase memory that won't work.  Can someone confirm which is the correct maximum amount of RAM for this model? Thank you!

Read other answers

Can I add an SSD drive to an Omni 27 (1200ev)  or do I have to replace the original drive? Ideally I'd like to retain the 2TB hard drive and have at least the OS on the SSD. Kind Regards, Brad

A:Can I add an SSD drive to an Omni 27?

Brad, Here are the specs for your HP Omni 27-1200ev Desktop Computer and its IPISB-NK (Lavaca3-SB) motherboard. Based on the specs, this model only supports two SATA drives. One SATA data cable for the hard drive and one SATA data cable for the optical drive. Please send KUDOs

Read other 8 answers

Hi Folks,

i am using omnipage 16 version for OCR purpose,i want to run the .exe in my application but the condition is it should run in the background meaning (NO GUI)..if i give parameters to it should take and processes it and giveback the output..the whole thing should be done in the background because the client shouldnot know about this Omnipage.

this is my urgent requirement.

A:Solved: Omni Page

I am not sure omnipage was intended for this purpose. I.e. the developers of omnipage want people to know that they are using their programme.

Read other 1 answers

I am not sure if I should ask here or in the laptop section since it is classified as a desktop, but the innards are more along the lines of laptop components. I have an Omni 100-5155 and looking for any upgrade options I may have (I do realize those options are extremely limited). I've already maxed the RAM to 8Gb, but am looking for CPU, hard drive and wireless possibilities. So my questions -What is the max capacity hard drive the motherboard will accept? I am hoping to also replace the optical drive with a hard drive caddy. Are SSD's and/or SSD/HDD hybrids supported? Can the PCI Express x1 802.11 b/g/n card be replaced by this? (to match my router's ability)Intel 3160 Dual Band Wireless AC + Bluetooth Mini PCIe card Supports 2.4 and 5.8Ghz B/G/N/AC BandsOr would I be better off getting a wireless USB dongle (if that would even work)? Any CPU suggestions or same form factor motherboard upgrade replacement possibility? I know my USB 3, better graphics and Gb WLAN dreams will have to wait until I've finished saving for a moderate gaming rig build, but I thought since I'm likely to be upgrading to Win 10 soon I should try to get the most I can out of this system... which will be eventually handed down to the nephews, hopefully within the year.  Any and all helpful suggestions will be appreciated. Thanks. For easier reference -Omni 100-5155 specsMotherboard specs   

Read other answers

Got and hp 120 omni all in one that came in a pallet of mixed ALL IN ONE DESKTOPS this one in particular has a POWER ON PASSWORD i figured out how to bypass some of these passwords by getting an error code. the problem is that this one does not give me an error code but a (*) character any help sugestions? i already tried removing the jumpers and putting them back in place with no success. ANY HELP WILL BE REALLY APPRECIATED  

View Solution.

A:hp 120 omni ALL IN ONE power on passworde

Hello, For you to be able to remove the Power On password, you need to remove the rear cover, then remove the metal cover that protects the motherboard and remove the jumper located close to the memory modules. Then try to power on the system and see if that resolved your problem. Thanks,

Read other 10 answers

I have had problems with the touch screen on my HP Omni 10 not working for some time, sometimes it works and sometimes not. Recently it has taken about 15 mins for anything to appear on the screen when I boot up. Now nothing appears on the screen when I boot up. I know the power is on as it buzzes when you touch the MS logo at the bottom of the tablet

Read other answers

When I insert the CD-R, the PC does not seem to recognize it.I cannot determine if this PC is even capable of burning to a CD-R.

A:I have an HP Omni 200 PC. I cannot burn a photo to a CD-R. C...

Hi, There are many HP Omni 200 machines, what is your ? The following link shows one of them             https://support.hp.com/us-en/product/hp-omni-200-5300-desktop-pc-series/5035328/document/c02671736 It should be able to burn CDR and CDRW. Please use CyberLink software which came with the machine to burn. Regards,

Read other 1 answers

Posted in the notebook section as this all in one uses mainly notebook parts. I am looking for the part number / availability of the option video card upgrade. I will also the proper hp heatsink. Other than knowing this a MXM type, I have been unable to find part numbers. Wish I had the option at time of purchase, but FRY's did not stock the unit with upgrades. Thanks

Read other answers

Please I really need your help. I don't know what happened with my desktop HP Omni 100Pc. I can turn it on but when it is about using it it completely crash and freezes.
It has windows 7 home basic 64 bits sp1 . It is an old computer but it was working great.

I'm unable to restore it to previous point because all my restore points where deleting. I was scanning my computer yesterday with norton antivirus and my hp turned off by itself.
If want to check my documents or even open a photograph, my computer crashes.
I used to use auslogic software but as it expired I opted to delete it.
Sometimes when I wanted to download something and the norton block I would turned off the antivirus for a while and turn it off. I rarely use my computer because mostly I do everything on my mobile device but since I started studying I really need and now it is not working. Please help me I don't know what to do and I don't have money to fix it or buy a new one

Sent from my iPhone using Tapatalk

A:My desktop all in one HP Omni 100Pc

Read other 7 answers

I currently own an All-In-One HP Omni 27 PC. For about 6 months now, the monitor has gone dark. The light at the top turns on and the fans will run, but the monitor will not come on or show the HP loading screen. I have tried the BIOS fix, but once completed, my computer does not reset like the instructions say it should. Has anyone else had this problem or know of a solution?Thanks,Noah

Read other answers

I got a HP Omni 27-1210xt into my shop last week and it had a bad hard drive, so i replaced the drive with the exact model and blew out the dust while i had it apart and after i put it all back together the video never displays, it did once but the unit shut off like 10 seconds after it came up, the other times you can hear the fans and the system running but just never shows a video, I have removed the memory and turned it on and it beeps so i would only say it rules out the motherboard or processor, so I'm looking for it to be video. Now I have located the processor but I do not see where the video is on this unit, doesn't appear to tbe onboard, maybe under some of the other covers? I'm about to strip it down some more. Any trouble shooting tips or ideas guys?

A:HP Omni 27-1210xt No Video

Still no comments or tips, anyone able to assist with this problem?Thanks

Read other 1 answers

I have a HP Omni 27. The computer is out of warranty. I had to have the hard drive replaced about 5 or 6 months ago. This morning my computer was working fine. Now I got home from work and my computer is at a black screen. I have done the reset that was mentioned by unhooking everything and holding the power button for 30 seconds. Still black screen. Please HELP!

A:All in one Hp Omni 27 blank screen

Hi @tanya21001, May the Forums be with you! It is a great place to find the help you need, from other users, HP experts and other support personnel. I understand that your Omni 27 is no longer  starting properly. I am happy to help with this. Please post the full product number and operating system on your Omni 27. See the following, if you need help with that information. How Do I Find My Model Number or Product Number?  Is the Windows Version on My Computer 32-bit or 64-bit? For now I will assume you are using either Windows 8.x or 10 so give this a try: HP Desktop PCs - Computer Does Not Start (Windows 10,8). Please let me know whether that works for you, and if it does resolve your issue, please mark this post as a solution. Kudos would also be appreciated.  

Read other 1 answers

I was in the middle of playing a game (agar.io) when my pc started flashing colors. First, a [red,green,blue,and white] screen, then alternating black and white. Then a combination of half black and half white, until it settles to an all black screen. After going all black, if I press a key on my keyboard it repeats everything. It does not allow me to go into safe or do anything at all. I can faintly see my homepage in the background. Even when I unplugged it and turned it on again, it's the same.

Read other answers

I recently replaced my desktop with a new HP desktop. I installed my scanner software (not new). I am now getting a message to register my scanner software at every startup. I find no way to disable this popup from the window that comes up, I cannot register through OMNI because it is likely no longer supported. Is there anything I can do from my desktop, short of uninstalling software, to eliminate this popup on startup?


Read other answers