I was reading these posts on the Hp all in one. The same thing has happen to mine. Just get a Blank screen. Did this end up being the Mother Board??? Mine is only 3 years old. Any information on how to preceed would be wonderful Thanks
I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.
I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.
You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)
Hi @esleman,Thanks for becoming a member of the HP Support Forums. I understand you are having an issue with blank screen. I will be glad to help you.Please post the full product number and operating system in use on your computer. See the following, if you need help with that information.How Do I Find My Model Number or Product Number?Is the Windows Version on My Computer 32-bit or 64-bit?Please get back to me with above information, so I can help you better.Read other 1 answers
I have a HP Omni 27. The computer is out of warranty. I had to have the hard drive replaced about 5 or 6 months ago. This morning my computer was working fine. Now I got home from work and my computer is at a black screen. I have done the reset that was mentioned by unhooking everything and holding the power button for 30 seconds. Still black screen. Please HELP!
Hi @tanya21001, May the Forums be with you! It is a great place to find the help you need, from other users, HP experts and other support personnel. I understand that your Omni 27 is no longer starting properly. I am happy to help with this. Please post the full product number and operating system on your Omni 27. See the following, if you need help with that information. How Do I Find My Model Number or Product Number? Is the Windows Version on My Computer 32-bit or 64-bit? For now I will assume you are using either Windows 8.x or 10 so give this a try: HP Desktop PCs - Computer Does Not Start (Windows 10,8). Please let me know whether that works for you, and if it does resolve your issue, please mark this post as a solution. Kudos would also be appreciated.Read other 1 answers
Hi all!I have an all in one Hp Omni 27-1001es and i have a really big problem!!! Yesterday i was working on pc and needed to leave it for some minute.When i got back the screen was blank and the pc looked freezed; i tried to reboot and nothing changed!!!!At start up the power button led works, the fan starts to work and the led of hard drive too but the screen continues without signal of life. Unplugged everything, opened the case to clean from dust, checked the Ram and nothing appears to be burned or disconnected. Thanx for any helpLeo
I understand your computer powers on but doesn?t show a display on the monitor, is that correct? I will be happy to help you.
If you haven?t tried already start with a hard reset.
1. Remove all cables from the computer including the power cord
2. Press and hold the power button for 30 seconds
3. Once done only insert the mouse, keyboard, and power cable
4. Try and turn the computer on to see what happens.
Please respond back at your earliest convenience.
I can hear the it load the windows screen in the background but theres nothing I can do I can not find a way to make it work. In desperate need any help would be grateful.Read other answers
i have 2 profiles one for myself and on for the kids. My profile is fine, however on the kids profile thier screen auto dims. No matter what you do, reset it to 100, it automatically dims right back to zero and we can not make it stop. Please help.Read other answers
HP Omni 120-1110ea Desktop PC 32 bit, flashing red, green, white in standby.I cannot turn it off just have to unplug from mains. Can anybody help?Read other answers
I have a hp omni 27 all in one. Had windows 8 upgraded to windows 10 didn't like it so went back to windows 8. After about a week or so of going back to windows 8 the screen started to give a flicker periodically then it eventually went blank. Not sure if windows operating system has anything to do with it anyway it powers on fan runs but no display. It abt3 1/2 years old. Took rear cover off nothing seems out of place or dirty. It's a 27-1210xt. Can anyone help? Thanks
Hi @Chipsaway,Welcome to the HP Support Forums! It is a great place to find the help you need, from other users, HP experts, and other support personnel. I understand you are having an issue with the computer has a black screen. I will be glad to help you. Please follow the steps from Computer Does Not Start (Windows 8). Please keep me informed of how things went. If you require further assistance, let me know and I will gladly do all I can to help you.Please let me know if this resolves the issue by marking this post as "Accept as Solution".To simply say thanks, click the Thumbs up below! Thanks.Read other 1 answers
Turned the computer on this morning, and the display is showing as split, with the left side of the screen showing on the right and the right side of the screen showing on the left, with a black line in the middle. This doesn't show this way when I remote into the system, only on the internal monitor. I tried changing the resolution, with no effect. Any ideas?Read other answers
HP Omni 120-1020t wakes from sleep mode with blue screen only. I hear it waking up, but nothing on screen except dark blue. If I unpulg power from back of computer, plug back in and press power button, it will start up normally with normal screen icons, etc.Read other answers
I hope someone can help - I woke up this morning and my Omni 100-5155 Desktop All in One will not work. When I press power there is no power on light and the monitor is dark. I can hear the computer starting up but I never hear the windows sound because it will not play until someone enters the password. I also do not see the system do the keyboard reconize check etc. it is just a little over 2 years old :-( I have disconnceted and reconnected all the power cords and connections. I thought about seeing if the BIOS is reconizing the hard drive but of course I will not be able to see anything without a monitor. I do have the recovery disks also but they won't do much good without a monitor. I also thought about hooking it up to my television (as a monitor) to see if the system is indeed working but that computer has no monitor port. Thank you for any input!
For your Omni 100-5155 screen being blank, I have included the following document 'Screen is Blank after Starting the Computer'. Please follow through the steps in order for the best results.
I worked on behalf of HP
I switched the screen to Game mode with the button at the side. But now the top button does not react. Why ? How can I fix it ? it worked until yesterday.ThanksRead other answers
I had to replace my HDD in my other laptop, well I put in blank HDD, well I try to start it up and I dont get bios or post. needing to install OS and software for the laptop. I tried the Ram trick, the hard system power reset and everything I could find that people suggested for the blank screen and bios problem.
I don't know that much about laptops but when you replaced the hard drive, how did you know it failed and how do you know something else hasn't failed?
Ok I need help. I am upgrading my dell dimension 4600i and I have a problem.
Here is what I bought......
Also Thermaltake TR2-430W PSU. and I have had an ATI X1300 video card.
Also have 1 Gb of G Skill DDR-400.
After checking and rechecking everything I get nothing no posts no beeps just a blank screen. Need some help please.
Thanks in Advance!
When you say you are upgrading your dell dimension 4600i, do you mean that you are replacing it completely or are you using any parts from it?
Got vundo and some months after that my screen was blank during bootup but came on when it got into windows.It shows at the very start of boot(where all the comp info is and some american logo) and then gradually goes black in about 2 seconds.Some more months after that, one day my screen was all blank and showed 'out of range' error.Then i booted into safe mode, ran online virus scanner and deleted about 15 entries of vundo.After that windows worked again but was still blank suring boot.
Another ting i also noticed that while an old game - IWD2 worked fine, when i enter IWD1 my screen immideatly goes blank and stays until i exit and restart monitor.when i restart monitor while ingame it similarly shows the picture for 2 seconds and then fades.However it works flawlessly while in windowed mode! I tried 640x480, 256 colors and compatibility modes - no use.
Same thing is when 3dmark03 is done with the 4 game tests and restarts itself to game test 1 my screen goes blank.
my monitor is also an old crt so i dunno what it could be.
I got the vundo probably from using internet explorer 6.0 :) anyway i fixed it and installed 8.0
My laptop was working fine the other day... Came back to it the next morning and the screen wouldn't come on and it kept resetting every 30 seconds or so. Once I finally got it to boot and get to sign in page the screen was all scrambled. But, everything else worked I could log in but couldn't do anything...
Anyone got a solution?
What do you mean scrambled?Read other 4 answers
This is a HP G70-227CL notebook pc, he has had it for a little over a year. He was on his email today and all of a sudden it went to a black screen and froze up. He rebooted it and when it restarted it gave us two options to restart normally or to let it fix the problem which was recomended and so we let it fix it.
It sat for about an hour or more with a black screen while we waited finaly changed to a dark blue then light blue then finally a box came up and wanted us to click on a opering drive below to fix the problem, but there was no operating drive listed in the box below.
It then said in the bottom to click load if nothing there, so we clicked load and it wanted us to insert an installation disk to load the drive and he had never got no instalation disks when he purchased the laptop. It took him about 20 min before he could get out of it, it was moving very very slow and not wanting to respond. It ended up shutting itself off and when it came back on it asked us again which option we wanted we tried the normal hoping it would give us something besides a blank screen, it started to come on normally then it jumped back to the first screen to give us the options again. it ended up deciding for itself to do the recomended option before we could click on anything and went back to a black screen. That is how it sits now, we have a white mouse arrow on the screen we can move around, it dont act frozen no more, but al lit has is a black screen.
We need this fixed we have thing... Read more
Read other 15 answers
Recently my laptop screen had to be replaced due to a cracked screen. Original screen was a Samsung and the new screen is LG. After this, whenever I install Intel HD graphics, windows boots up till the login screen and then goes black, one bright flicker, then completely black again. However, when I boot into safe mode and replace Intel HD graphics driver with Standard VGA adapter, everything works fine, except for crappy graphics ofcourse. I tried installing various old/new/latest versions of driver software, upgrade/downgrade BIOS, install monitor.inf file from lenovo website for this laptop model, everything.
Odd thing: running Dxdiag shows my current display to be 1200x800 (32bit)(1hz).
So, I tried to change the display refresh rate in advanced settings> Screen refresh rate, no luck, no other option except ' Use hardware defaults'. So, I went ahead an modified registry values as given here:
How to Modify the Video Refresh Frequency in the Registry
Again, no use. After I reboot and go back and check, its set to 1 by default.
Tried 4 clean installs, installing on a completely new HDD, Windows 7 Pro, Windows 7 Ultimate, Windows 8 , everything..
Is it a screen problem? Or some hardware ID kind of thing?
What should I do ?
Time of this report: 2/3/2015, 06:26:14
Machine name: UNKNOWN-PC
Operating System: Windows 7 Professional 64-bit (6.1, Build 7601) Service ... Read more
Not all laptop screens are the same. It is important to get a "replacement" screen, not a "compatible" one.
On the back of the laptop screen is a product sticker (you can only read this before you install the screen). On that sticker is the manufacturer and model #. You can use that number to find exact replacements.
How did you come to choose the LG screen?
i'm having to boot into windows xp. on power up sytem goes through the windows xp splash screen (with progress bar) and then instead of login prompt it goes just into the blue screen with moveable mouse pointer arrow.
issue seems to be similar to:
but recommended solutions didn't help so far.
symptoms just before issue - was not able to run use some system features - utility to turn off the display, utility to bring up battery info - everything was working fine before this
what i've tried:
boot to Last Known Good Configuration - resulting in the same blue screen
boot to Safe Mode / Safe Mode with networking / Safe Mode with comman prompt - resulting in blank (black) screen with "Safe Mode" in the corners and moveable mouse
test the hardware (hard drive / memory etc.) via build in PC Doctor - all seems to be working
i am able to use bootable XP CD from other machine to get into Recovery Console
i am able to boot to simple live XP using BartPE-XPE usb key and access the hard drive
could you please help me to find solution to this issue
thank you in advance
Hi krajicek, u having a same problem as me.
Btw.. yours is laptop or desktop?
If laptop wat brand are u using..Mine are FUJITSU laptop and i still
can't get it work.
I boot from the WinXP CD and it still can't recovery as well and i try
safe mode aslo can't work too..
Starting yesterday my computer would go through startup... while loading the desktop it would crash to blue screen with white text (unfortunately, I can't remember the exact error message). If restarted, it either goes to a blank black screen or back to blue, and I could only get the computer to operate in safe mode with networking. My antivirus software (avast free, malwarebytes)scanned and found no infections.
I have Windows 7, Samsung laptop.
Today, I was able to start the computer normally and am functioning with internet (still acting a little funny), but I am sure something is still not right. I also did a system restore last night, with the same problems (crashing, not starting up).
Any assistance would be highly appreciated!
Thanks in advance,
PS: I (goofily) started a similar topic in the "Windows 7" forum section without knowing this section was down here... Sorry! I tried to delete the topic/post but couldn't. Thanks.
Hello,I will be helping you with your problems. Please be patient while I assist you.Some points for you to keep in mind while I am helping you to make things go easier and faster for both of us Please do NOT run, install or uninstall any programs, unless instructed to do so.
We ask you to run different tools in a specific order to ensure the malware is completely removed from your machine, and running any additional tools may detect false positives, interfere with our tools, or cause unforeseen damage or system instability. Please do not attach logs or use code boxes, just copy and paste the text.
Due to the high volume of logs we receive it helps to receive everything in the same format, and code boxes make the logs very difficult to read. Also, attachments require us to download and open the reports when it is easier to just read the reports in your post. Please read every post completely before doing anything.
Pay special attention to the NOTE: lines, these entries identify an individual issue or important step in the cleanup process. Please provide feedback about your experience as we go.
A short statement describing how the computer is working helps us understand where to go next, for example: I am still getting redirected, the computer is running normally, etc. Please do not describe the computer as "the same", this requires the extra step of looking back at your previous post.NOTE: At the top of your post, click on the Watch Topic Butt... Read more
I did a bit of research and this seems to have been an issue for a while, or has been in the past. Was upgrading to windows 10, I first had to restart my pc cause it was initially stuck on that preparing to install problem with the green bar being stuck around 25%.
It then got through that and began the installation process with the big circle and rebooting process. However around 91% when I last looked at it it was just black screen, this stayed this way for about 3-4 hours. I then decided to reboot the pc and it has now booted to the login screen. Is this a known bug or could there be a possible issue?
The problem seems a bit different as some people I saw have had to fall back on PC restore points etc. So not sure if it installed or what could be the problem.
Also side note, I upgraded my pc when windows 10 first publically released, but rolled back because I had about 5min shutdown times. So not sure what is going on and any info would be greatly appreciated!
I never had a problem upgrading like you've experienced but I experiencing Windows 10 upgrading process is the longest time taken ever compared to previous versions. It took me 1 hour+ to finished.
Play around a little bit to get used to it then did a clean install. No problem arise, seems working fine.
The point is, problems always happen after upgrading, to solve it just perform installation from scratch (clean install).
Very similar to the following problem but i do not have a raid, and it seems that this PC has a raid and i don't, plus it was never really determined what the actual solution was.
The basics: XP Professional Boot up screen, right before the windows loading screen, or direct after the F8 Menu if you hit "Start Windows Normally..." it will just lock up, no HDD activity, blank screen. now BSOD, nothing.
All 3 safe mods work fine.
Ran chkdsk /r in recovery.
Ran proper fixboot procedure.
Went into safe mode and checked the event viewer.
The only concerning message i got was: The following boot-start or system-start driver(s) failed to load:
Formatting really isnt an issue since i can back up anything i need through safe mode. However its just the fact that the Windows gremlin has struck me again and i must defeat it once more.
I highly doubt this is a hardware issue as it is more of a driver/software issue.
Anymore information for me, or from me that you need, i would be extremely happy.
Thanks for your time.
Before I say the hard drive is dying, you need to try the XP repair as you have done most else you can already:
pavilion dv6000 start screen blank if screen not fully open, external screen fine and shows login infoif fully open all is fine, after login screen it can be partially closed or pulled back and will operateRead other answers
I recently changed motherboards and removed a 2nd hard drive which contained win 8.1. The system now has one drive with Win 7 Pro on it. My backups have been going to a removable seagate usb 3.0 drive and was not always plugged into the system, so occasionally I got a notice that windows couldn't find the backup drive which was not a problem as I plugged it in weekly and backup ran fine then.
What I've done so far:
1) sfc /scannow from elevated prompt, no files had problems
2) ran MRT and virus scan, came back negative
3) Started system repair disk and selected Startup Repair and came back with no problems, ran additional available troubleshooter which came back with no problems found.
The full error message reads:
"The backup application could not start due to an internal error:
The service cannot be started either because it is disabled or because it has no enabled devices associated with it. (0x80070422) "
When I select "Backup and Restore", the page comes up showing only the words "Control Panel Home" in the upper left in the blue area and the words "Backup or Restore your files" in the top white area of the page. The rest of the page is blank. See attached pdf ...
Not surprisingly then, the service doesn't show up in msconfig as a startup service.
The error is supposed to be, according to technet articles, indicative of a corrupted file, however as stated above System File Checker finds nothing.
Thanks in advan... Read more
Windows Backup was disabled in "Services" for an unknown reason. Also, I was looking for "Backup and Restore" at the top of the list of services instead of Windows Backup at the very bottom of the list. I didn't look in "Linux Backup and Restore", either. Duh. Anyway, good news, easy fix. Done.
"Start > right click "Computer" > select "Manage" > select "Services" > select "Windows Backup" from list and double click it. When the pop up window opens, if the pull down says "This service is disabled" click on the pull down and select Manual. Click "Apply". "OK". Done.
Now, just go to backup and restore in the Maintenance folder on the start menu program list, click it and Backup menu is there ready to go.
pavilion dv9600 entertainment start screen blank if screen not fully open, external screen fine and shows login infoif fully open all is fine, after login screen to the pc it can be partially closed or pulled back and will operate in the window environment perfectly
Hi @reneC, Good day! Thanks for posting your question in the HP Community. It is a terrific place to find answers and tips and to have the best experience in the HP forums. I read the post regarding issues with the display which works at a specific angle. I?ll be glad to assist you with this. You are a valued HP customer and we appreciate you greatly for doing business with HP. I have reviewed the situation and it is paramount that we address your issue. Thank you for giving us the privilege to assist you on this platform. You?ve done some awesome diagnosis and troubleshooting. Kudos to you on that score. . I would require more information regarding this to assist you better.· When did this first occur?· Please provide the complete model# of the unit.As this is an older computer, service options with HP may not be available as the parts for this unit is not supplied anymore by our business partners. I request you to contact a technician locally, like Best Buy or Staples and get the situation corrected. Hope this helps. Let me know how this goes. I genuinely hope the issue gets resolved without hassles and the unit works great. Please reach out for any issues and I'll be there to assist you. To simply say thanks, please click the "Thumbs Up" button to give me a Kudos to appreciate my efforts to help. If this helps, please... Read moreRead other 3 answers
sir,i do have lenovo G500 and since a month i am facing problem of blank screen when i turn on my laptop by pressing power button.have tried all the ways to resolve the issue but helpless it doesn't show anything on the screen and shows simply a blank screen and glowing led of power.kindly help in this issue.Read other answers
After the Starting Windows screen a blank black screen with a cursor that I can move pops up that lasts a minute (shouldn't happen with SSD, used to be ~10 second boot). Afterwards the login screen will appear as normal and everything works as normal. This doesn't happen when I boot into safe mode.
I attached a list of start up services, installs, and scheduled tasks, along with my latest boot log.
Hello and welcome, try this to see if you have something that's going you don't know about. Use the free version.
SUPERAntiSpyware | Remove Malware | Remove Spyware - AntiMalware, AntiSpyware, AntiAdware!
Bonjour mes amis.
I recently have started getting the infamous black screen of death at my computer's startup, very similar to this fellow user's problem. Basically, Blank screen on boot up, before login screen; slow startup. The black screen lasts at least two minutes on average, before the windows login screen comes up. Everything else runs fine!
I think it might be my antivirus, Bitdefender Total Security 2013, and I've posted on their forums about it, and I've gotten responses from other users saying:
The Black screen issue is known by BD Support till now they have not able resolved that issue.
hope BD 2014 resolves the issue.
And the booting time issue is been solved.
However, I uninstalled Bitdefender and the problem still persisted. I proceeded to uninstall every program i could remember installing before the problem started, so before the start of June. This was painful because I updated all my software, so everything was listed as installed recently.
My startup time after removing all these software is attached below; 156 seconds, compared to before with the speed ranging from 200-500 seconds, with the worst at 472 seconds.
Although this sped about my startup, I still got the annoying black screen issue. I am sure it is a software issue because the black screen is present, but lasts no longer than about 5 seconds when starting in Safe Mode with Networking, and is present even int he low graphics.
What should I d... Read more
Hello mate try some of these Troubleshooting Steps for Windows 7 start at point 15 then do chkdsk Disk Check
The go through the other stuff.
Oops should have mentioned this one too start at point 7 - option 3 Optimize Windows 7=Performance Maintenance
I have a Dell Inspiron 1750 laptop with core 2 duo (I forget how many GB the hd is) that had Windows 7 Home Premium edition installed on it when I got it. (I have no idea where any of the CDs that came with it are now.)I had been having problems with the login screen just flashing from the blue background image to black and the mouse just showing the circle thing with Please Wait... showing, instead of loading the icons. Normally, there are two icons that show up. One is the Fast Access icon that has facial recognition and the other icon is the one to type my password.
It would only run in safe mode, and none of my restore points would make windows load normally, but I know next to nothing about computers and wasn't able to find a tutorial on how to fix it, so I downloaded Ubuntu instead by using Windows in safe mode with networking. I was having problems with Ubuntu freezing, so on the next startup I chose to run diagnostics tests and the monitor connection test & the sata confidence test both failed, while everything else passed, which I don't understand because I wasn't having any problems with dead pixels or colors or anything or saving any files. (I think the hd test said something about $I30 31344?) I went into bios setup and clicked factory restore or something along those lines, thinking that it would restore Windows to how it was when I first got the laptop and now, it loads the Dell circle at startup followed by a black screen with a white blin... Read more
So I've had this computer for almost a year:
HP Pavillion a1250n
250G Maxtor HDD
2x 512mb DDR 3200 ram 400Hz (1Gig)
Brought to it's knees this weekend enexpectedly, I am attempting to install Windows XP Pro. I have used the maxtor diagnostic util to wipe the HDD to all zeroes, leaving one big unpartitioned space.
When I boot from the Windows XP CD it goes though the install just fine, formats the space, and copies the files, seemingly alright. When it reboots, it goes through the whole BIOS screen fine, it again asks to press any key to boot from CD, and if nothing is pressed goes directly to a blank screen, no cursor, no loading, nothing. Leaving it for up to an hour does nothing. Monitor is on, and signal seems active, but nothing is coming though.
I can access recovery console, but I'm getting in over my head at that point. Can anything in there help me?
Any advice is good advice, I messed with this all weekend long and it is getting old.
When the PC reboots after copying files it should then read from the boot device, it may be possible that the BIOS is set incorrectly with the boot device not being set as the bootable drive.
Go into BIOS and ensure that the first bootable device is the HD you are loading windows onto, also remove any devices attached to the bootable drive such as any slave drives and that the jumper is set to master, not slave or cable select, if the CD rom that you are loading windows from is slaved to the master drive then place it on its own IDE channel and rerun the setup from scratch.
The only other time I have seen this happen is when the drive itself is flaky, that was only once though and I had to replace the drive.
Hello everyone. I'm new the the forums here (as in just registered), but I need some help please. Basically after attempting to open firefox today (as I have probably over 20 times a day for the last year at least), I received a blue screen of death, and now my computer seems to be shot. I know how difficult it is to diagnose something without being able to see it, so I made a short little 4 min video of me trying to turn it on and what it does. Hopefully this has happened to at least someone before.
Blue Screen of Death - YouTube
From the video you provided (which is great, by the way)... your system is failing to POST. Essentially if the system detects that a device or component is failing to provide the accurate information, which ensures that it would then be safe to run, the system will not POST.
From the looks of it, your hard drive or memory appears to be the issue which is the issue in most of the cases like this as you're BSOD'ing right after loading the Windows disc and after it loads the files necessary for the install.
My current advice:
1. Clear / reset the CMOS and try booting up and or loading the disc again.
2. If possible using another system, possibly a laptop... etc, download and run Memtest86+ -
Download Memtest86+ here:
Which should I download?
You can either download the pre-compiled ISO that you would burn to a CD and then boot from the CD, or you can download the auto-installer for the USB key. What this will do is format your USB drive, make it a bootable device, and then install the necessary files. Both do the same job, it's just up to you which you choose, or which you have available (whether it's CD or USB).
How Memtest works:
Memtest86 writes a series of test patterns to most memory addresses, reads back the data written, and compares it for errors.
The default pass does 9 different tests, varying in access patterns ... Read more
Really frustrated after buying Lenovo Y700 15ISK recently. All drivers updated even applied steps from this post but still randomly screen goes blank (Black screen) while the power is still on. Also observed that harddisk light blinking turns off too after this. Is it hardware related issue?Please help to resolve it.Read other answers
Need help here.
I have a HP laptop DV9543cl with 32bit Vista. Last Thursday (6/3/2010), Vista update icon showed up and asked me to install the update. As always, i did that. Once install was done, it asked for a reboot which i did. It started booting up again and when it finished Windows logo screen, it went blank and no display with all the other lights were in correct status. I waited for a long time before attempting a reboot. Since then i don't see anything on the screen after the initial BIOS screen (Which is also all jumbled up). I tried F8 (BIOS) and F11(Restore) but no screen. Don't know what to do but i am pretty sure that Laptop is working ok just not displaying anything. I am going to try Remote desktop on it now.
Any help would be greatly appreciated.
have you tried ringing up HP support line?Read other 5 answers
Using window xp pro
I on computer.
It's fine loading bios and till window xp logo..
when it starting to load the welcome window screen.. (which it didnt reach the welcome screen at all)
It just stuck at the black screen..
so i try to run in safe mode, weirdly it able to open.. okie
i tried to reformat... but it doesnt seems to work, it happens the same thing..
b4 this happened.. it all started one day.. i let my computer to download some personal stuff.. then, my bro went to play gunz online.. so the computer got hanged, and he just shut the computer just like that.. (how stupid) so now, i cant reach the welcome screen at all.. help me pls..
I'm using pentium 3..
as yall know, im a beginner, i dont know a thing.. just tell me what to do if u need any informations..
Try this, boot into safe mode.
Right-click on "My computer" and select "manage"
When that opens, click on device manager
When device manager opens, look at your graphics card normally under "display adapters" - any crosses or red splats?
When i connect my laptop to my HDMI tv and when i try to play any video on youtube or from hard drive the screen goes blank and i here only audio when video is played in fullscreen. This happens only for 1080p resolution. I have full hd tv and i tried other laptops that works fine. Please anybody have any solution to this problem?
Same problem on my HP PavilionRead other 1 answers
I'm not sure if this is one virus or if my computer has somehow picked up several, but it is pretty much completely screwed. I can't access ANYTHING properly so i am posting this message from another computer.
This is what happens when I turn my computer on:
1. blank blue screen with program error message: "explorer.exe has generated errors and will be closed by windows....".
2. if i click "ok" the message goes away and i am left with a blank blue screen and i have to reboot the computer
3. if i don't click ok windows starts to load up an looks normal at first but then another error message pops up (the same one) and the screen turns black and says some junk like "Warning! You're in danger!" and then some junk about spyware.
4. then a few seconds later another error message pops up and the screen turns white and says "Active Desktop Recovery. Microsoft Windows has experienced and unexpected error..." It gives me an option to "click here to restore" but nothing happens when i do click it.
5. and then another error message pops up and the screen goes black again, then another message and it goes white and so on.
I can't really open any programs properly because another error message will pop up and shut down the start menu before i get a chance to open anything.
I managed to run ad-aware and it found some problems that i cleaned up. then spybot found nothing. then i rebooted and was having the same ... Read more
Yes, you've got a few malware entries in there (a CoolWebSearch hijack, and a couple of trojans), though it's not going to be easy to remedy without seeing the complete HJT log. Can you possibly copy the log to floppy and then post it from the other computer?
What's the Windows OS?
eg. Is it Windows 2000 sp4? Or is it WinXP Pro sp2?
What version of HijackThis is it? v1.99.1 is the latest version.
Is HijackThis.exe running from a permanent folder, and not from within a zip file in a Temp folder?
This is important. Make sure HijackThis.exe is installed in eg.
Re: your questions at the end of your post:
Don't worry about WINNT / winnt and System32 / system32
They are both exactly the same (whether smallcase or uppercase or a mixture).
svchost.exe is legitimate and is an integral part of Windows NT/2k/XP (Services Host).
It is normal to have multiple instances of it running.
Anyway, try this for now...
If possible, please download the following apps and transfer them to the infected pc.
CWShredder (free standalone version)
You will need to unzip AboutBuster.zip to a folder on the good pc,
then open AboutBuster.exe
click the Update button
dow... Read more
I have a Compaq Presario C300. Somehow the screen cracked and of course was not under warranty. I purchased a replacement screen online and followed the directions to replace. It was relatively simple, however, now when I boot up the computer, the backlight comes on for the whole screen, but shows up blank. Did I just not fully connect something? Is there something simple I can check before I bring the whole darn thing in for service anyway? This is what I was trying to avoid in the first place. The whole laptop was only 800 and the new replacement screen was $199 (as opposed to the quote for $450 I got to have it replaced).
Anyone have any ideas I can try?
You have to make sure you bought right screen for your laptop. Check your connection cable hasn't any damage on it. If it still shows only blank screen, i think not coming enough power for screen (wrong screen).
I cant get into my desktop. When i start my pc XP loads, and it starts the last known good configuration. I then seen the xp loading screen.
Next i should be able to see the login screen, however this is a blank black screen, the mouse is visible and i can move it around the screen, but i cant see anything to log into the desktop.
I dont know why this has happened, it was working last night. The only thing i can think of was my brother switched the power off as it was shutting down. The shut down had automatic updates running (i think) at the time the power switches were turned off.
How do i solve this so i can see the login screen and get into my pc?
Hope someone can help, cheers.
Boot into Safe Mode Options Screen (the one with Last Known Good Configuration on it) by pressing F8 at bootup and choose
'Safe mode with command prompt'
At the command prompt type
Hopefully this will open System Restore, so restore to before the problem started
From last few weeks I'm having this strange and annoying blank screen of death. I could just see a blank screen (not a blue screen) while either waking up computer from sleep or while trying to turn on the display by moving cursor/typing something(waking up from power saver mode of display, I set display to be of after few minutes of inactivity). So essentially screen becomes total blank. Just once or twice I saw this BSOD "DRIVER POWER STATE FAILURE" but for all other times my screen is just blank. I could see the Hard Disk activity LED on during this blank screen. And almost after all subsequent boots, I could see "Windows has recovered from unexpected shutdown/serious error - Check for solution" message.
System - Windows 7 Pro x64 with all latest recommended and security updates
CPU - i7 2630QM
GPU - nVidia GT525M
MoBo - Factory default for Dell XPS L502X
First I suspected its because of my nVidia GT525M GPU drivers (I was using official latest drivers 320.49), so I completely uninstalled them with regular uninstall + DriverSweeper 2.1.0 from Guru3D.com. I did not install any nVidia/display drives since then. But just now I got another blank screen after it. Also I started connecting my PC to an old Sony Bravia TV with HDMI cable and that time the automatic installation of drivers failed. That is my second point of possible problem. I've been using CCleaner to clean the unwanted registry entries and revo uninstaller for almost every unin... Read more
The BSOD is caused by Intel(R) Centrino(R) Wireless-N 1030 driver.
Irp is active with 5 stacks 3 is current (= 0xfffffa800760f840)
No Mdl: No System Buffer: Thread 00000000: Irp stack trace.
cmd flg cl Device File Completion-Context
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
>[ 16, 2] 0 0 fffffa8009cd4050 00000000 00000000-00000000
Unable to load image \SystemRoot\system32\DRIVERS\NETwNs64.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for NETwNs64.sys
*** ERROR: Module load completed but symbols could not be loaded for NETwNs64.sys
Args: 00014400 00000000 00000004 00000002
[ 16, 2] 0 e1 fffffa8009d9e470 00000000 fffff8000370b200-fffffa800c1f7510 Success Error Cancel pending
Args: 00014400 00000000 00000004 00000002
[ 0, 0] 0 0 00000000 00000000 00000000-fffffa800c1f7510
Args: 00000000 00000000 00000000 00000000
And the driver is old.
fffff880`06cd3000 fffff880`07555000 NETwNs64 T (no symbols)
Loaded symbol image file: NETwNs64.sys
Image path: \SystemRoot\system32\DRIVERS\NETwNs64.sys
Image name: NETwNs64.sys
Timestamp: Tue Jun 21 22:40:03 2011 (4E00D06B)
CheckSu... Read more
Hey, first time posting here, so sorry if this is the wrong section or anything.
Lately my laptop has been experiencing a problem when I boot it up. After the Starting Windows screen with the glowing Windows logo, a blank black screen pops up that lasts for ages (I'd say at least 5 minutes). Afterwards the login screen will appear as normal.
When I log in, the desktop appears quickly, but when I try to start any programs, like my browser, they are slow and freeze often (usually I can run programs with no problem when the desktop appears). Sometimes the laptop will hang every three seconds. It takes a bit of time before the programs and the laptop run like normal.
I've tried several things without success:
-Uninstalling and reinstalling graphics drivers (I've never updated my drivers because no updates are ever available for my driver; is that normal? My laptop is about two years old)
-Defragging hard drive
-System Restore (I don't seem to have any restore points)
-Startup repair (or whatever that first F8 option is called)
Welcome to Seven Forums Tienjt.
You can run this SFC /SCANNOW Command - System File Checker and post back with results.
Below my sig is a link to MalwareBytes, download the free version, update it, and run a full scan.
Have you installed anything new, hardware or software? Sometimes OEM's don't/won't have driver updates.
First I run Windows 2000 and keep it updated as much as Microsoft releases updates. I also reguarly run anti-virus, anti-spyware, defrag, etc. The problem started 2 weeks ago when I booted the computer it showed the MB splash screen and then instead of the 2000 loading screen it just showed "Error loading OS." in the top left. Well I figured the hard drive was going so I pulled it out, blew it off, tapped on it, checked connections and stuck it back in. Rebooted and everything seemed fine and has the past 2 weeks. Well today I was playing Civilization 4 and the screen went blue. Yes the dreaded blue screen, but no error messages on the screen or anything. Just a solid blue screen. The computer didn't respond to anything so I pushed the power button on the case. Well upon restarting nothing happens. Just a blank screen. No MB splash screen or anything. Everything is powered up and I can hear the hard drive spinning, but nothing is on the screen.
Windows 2000 Pro
ASUS P4C800E Deluxe mobo
1.0 GB Kingston ValueRAM
Maxtor hard drive (Old)
Any help is appreciated.
Doubt this will help but have you tried seeing if you can start in safe mode?
Reboot and hit F8 as it tries to start up. Think it is F8 in 2000
hello , i have issue hapen randmly and get Blank Screen or Weird Colorful screen and the computer not respond,and i run hardware scan i get Result Code: WCP03E000-UL7DVI passed, so Please can any one help me to now what is the proplem
p50.jpg ?4839 KB
I'm getting a blank screen when my computer boots up. Not even a Bios screen or anything. But, Win 7 seems to boot up fine in the background. I can hear the welcome chime in the background after a little bit.
I was in the process of putting in a new SSD when this happened. Tried to unplug it and restart, but same problem. Now I have everything else unplugged but the graphics card, and the old hdds. Still nothing but blank screen.
I'm wondering if it's the graphics card or the power supply that are spotty. Fan is spinning on the graphics card, but I'm not sure what to make of that by itself.
Not quite sure what to do now....
Mobo: Gigabyte 870A-UD3 AMD
CPU: AMD Phenom 2 X4 955 Black Edition
RAM: GSkill DDR3-1600 4GB
Graphics: MSI N460GTX Fermi
Power: OCZ Fatal1ty 550W modular
OS: Win 7 Ultimate OEM - clean install
You might have the splash turned off in the bios. Have you checked the settings in there. When the computer boots start hitting the button to get you into the bios seeing as you can't see it.Read other 9 answers
I have a Win XP Home edition that fails to boot; the POST screen loads, then a choice of operating system configurations (see later), and selecting one of them (the last on the list) returns can’t find hal.dll.
The other two options, one of which I have set up in the course of trying to sort this out, both end up with a blank screen.
Safe mode hangs up in the middle of the driver list.
The problem started after a power cut.
I have fairly exhaustively investigated and tried to fix this as follows:-
Seagate 250Gb disk in four partitions, C,D,E,F. Using a partition tool confirms that the active and primary partition is C. The files on all the partitions are all visible using file explorers on bootable recovery CDs (ERD Commander and HIRENS). I have been able to back up the important data. The operating system files are on C partition only.
Run disc diagnostic – passed, no errors
Run Memtest86+ - passed
Run chkdsk /f – fixed a couple of errors
Via recovery console on original disk
Run fixmbr, reboot, not fixed
Run fixboot, reboot, not fixed
Run bootcfg /rebuild fixboot. Reboot, not fixed (this is the most recent listed configuration)
Tried repair install from recovery console. Copied files etc, then automatically tried to reboot but stalled at same place.
I have also tried the disk i... Read more
I would clone the drive, then do a clean install.Read other 3 answers
I have a refurbished, out-of-warranty Gateway Profile 5 desktop. The screen is totally blank. I contacted Gateway. They are pretty confident the built-in display is defective. I was able to attach a second display which would also go blank just after the Windows XP Pro splash screen appeared. Using the 2nd display, I was able to access the bios. When I looked at the display setup, it was set to LCD & CRT. Not thinking, I changed the setting to LCD since I wasn't using a CRT. That disconnected my 2nd display, so I now have two totally blank screens. How can I re-access the 2nd display and then also avoid a blank screen when Windows XP boots up?
I've got a problem with my laptop, a 2010 HP G60-635DX. First, a little history. This was my wife's laptop until she dropped it and broke the display screen. We hooked it up to a monitor and she was good to go. Last Christmas I got her a new computer and again she was all set. In the meanwhile I've been using this old Dell laptop from 2006 with WinXP in it. Works, but is slow as all get out. A few months ago I decided to use my wife's old computer for myself. It comes with Windows 7 and works quite well. Last June I made the mistake of trying the Windows 10 upgrade, and what a disaster that turned out to be. So I reverted back to Win7, but I lost all the drivers that came with it, so I was stuck. So recently I bought a new screen for my wife's old computer, and I installed it today. So guess what? The screen works fine, but all I get is a blank white screen Nothing at all! It's as if the computer can't display anything at all. I just don't understand it. The computer fires up, but that's it. No start screen, no nothing. Just a blank white screen.
Anybody have any ideas as to what's wrong, and how I could fix this?
I got the computer working! Last night I rechecked the connections to the screen and made sure that they were solid, then all of a sudden the Startup Utility came on, asking me what I wanted to do. So I opted to wipe the HD clean and revert it to the original factory specs (don't worry, I have all important files backed up already). I made sure the connector cable was in there good, then I stuck a piece of electrical tape on it just for safety. Now the computer runs as good as new, and I don't have to spend any money taking it in to a shop.
The moral of the story is this - always check and recheck your connections. Lesson learned!
I have a all in one HP OMNI 200 pc. The computer came with windows 7 but was upgraded to windows 10 about 6 months ago. Was trying to do a recovery/reset and it froze up with the following message:RecoveryYour PC /device needs to be repaired. The operating system couldn't be loaded because the kernal is missing or contains errors.File:/windows/system32/ntoskrnl.exeerror code 0xc0000221Read other answers