Over 1 million tech questions and answers.

Windows 7 very slow in normal mode, runs fine in safe mode with networking

Q: Windows 7 very slow in normal mode, runs fine in safe mode with networking

Hi
 
I am looking for help 
 
My windows 7 start in normal mode is very slow.  System is in a loop or is hanging waiting for the hard disk to be free.  The hard disk indicator light is on  all the time ... 
When I start the system in safe mode with networking, the system is fine and nothing is holding the hard disk anymore.
 
I ran minitoolbox and got the following error indications 
 
MiniToolBox by Farbar  Version: 20-06-2014
Ran by Toshiba (administrator) on 21-06-2014 at 22:59:54
Running from "C:\Users\Toshiba\Downloads"
Microsoft Windows 7 Home Premium  Service Pack 1 (X64)
Boot Mode: Network
***************************************************************************
 
========================= Devices: ================================
 
Name: Security Processor Loader Driver
Description: Security Processor Loader Driver
Class Guid: {8ECC055D-047F-11D1-A537-0000F8753ED1}
Manufacturer: 
Service: spldr
Problem: : This device is not present, is not working properly, or does not have all its drivers installed. (Code 24)
Resolution: The device is installed incorrectly. The problem could be a hardware failure, or a new driver might be needed.
Devices stay in this state if they have been prepared for removal.
After you remove the device, this error disappears.Remove the device, and this error should be resolved.
 
Name: Microsoft Teredo Tunneling Adapter
Description: Microsoft Teredo Tunneling Adapter
Class Guid: {4d36e972-e325-11ce-bfc1-08002be10318}
Manufacturer: Microsoft
Service: tunnel
Problem: : This device is not working properly because Windows cannot load the drivers required for this device. (Code 31)
Resolution: Update the driver
 
 
**** End of log ****
 
I thought initially this could be a hard disk error, but the system and the hard disk are performing fine in safe mode with networking 
 
So what could be the problem ??
 
Thanks

RELEVANCY SCORE 200
Preferred Solution: Windows 7 very slow in normal mode, runs fine in safe mode with networking

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: Windows 7 very slow in normal mode, runs fine in safe mode with networking

Could have crap ton of stuff starting up with windows.
perhaps corupt driver or installed the wrong driver.

Read other 2 answers
RELEVANCY SCORE 168.4

Hello,
 
all of a sudden Windows 7 became extremely slow in normal mode. This doesn't happen in safe mode.
 
The laptop now also makes 3 beeps on startup, but the beeps disappear when Windows login page comes up. The only thing I did is updating Java and the beeps started.
 
I'm sending in attachment DDS, OTL and ComboFix logs.
 
Thanks in advance for your help!

A:Windows 7 runs fine in safe mode, but very slow in normal mode

Hello maestrale,

Welcome to Bleeping Computer.
My name is fireman4it and I will be helping you with your Malware problem.

Please take note of some guidelines for this fix:
Refrain from making any changes to your computer including installing/uninstall programs, deleting files, modifying the registry, and running scanners or tools.
   If you do not understand any step(s) provided, please do not hesitate to ask before continuing.
   Even if things appear to be better, it might not mean we are finished. Please continue to follow my instructions and reply back until I give you the "all clean".
In the upper right hand corner of the topic you will see a button called Follow This Topic.I suggest you click it and select Immediate E-Mail notification and click on Follow This Topic. This way you will be advised when we respond to your topic and facilitate the cleaning of your machine.

   Finally, please reply using the Post  button in the lower right hand corner of your screen. Do not start a new topic. The logs that you post should be pasted directly into the reply, unless they do not fit into the post.  1.Download AdwCleanerDouble click on AdwCleaner.exe to run the tool.
***Note: Windows Vista and Windows 7 users:
Right click in the adwCleaner.exe and select "Run as administrator"Click the Scan button.

Once the scan complete click Clean to finish cleaning any thing it has found.A logfile will automatically open after the scan h... Read more

Read other 28 answers
RELEVANCY SCORE 162.4

I recently re-formatted my Sony VAIO since it was starting to run super slow. Now that I re-installed Windows 7 on it through recovery disks, it worked fined for about a day but then the problem came back. The computer is slow at bootup and runs super slow while freezing so many times. I am running it on safe mode right now and its working fine.

I ran hardware diagnostics and everything is fine (Memory, Hard Disk etc.)

I installed Norton Antivirus and Windows Live Messenger after the re-install.

Please help me.

A:Computer runs really slow in normal mode, but runs fine in safe mode

anyone?

Read other 9 answers
RELEVANCY SCORE 152

Hi,
 
I could use some help. My Toshiba Satellite laptop is having issues after the normal startup with slowing down dramatically after it goes to the desktop. It will basically freeze with commands taking between 5-50 seconds to be recognized and sometimes it just freezes. When I boot into Safe Mode, I am running everything smoothly. I could really use some help figuring out whats going on.

A:Everything runs very slow in normal, but fine in Safe Mode.

Open msconfig and on the General tab choose "selective startup" (uncheck all three items) and reboot. Does the problem still occur? If not, start adding items back to msconfig one or two at a time, rebooting after each change, until the problem reappears and you'll have identified the offending process. This is clearly a time consuming procedure, but it is the best way to determine if some process loading with the system is the cause of your problem.
 
After you've isolated the cause, do not use msconfig to permanently disable the process. Instead, if it is a service go to START - RUN and type: services.msc (then press enter) and disable the service OR, if it a program, you can download & run a simple app such as Mike Lin's Startup Control Panel (http://www.mlin.net/StartupCPL.shtml) to enable, disable, or otherwise manage startup programs.

Read other 1 answers
RELEVANCY SCORE 150.4

Hi, I navigated to this site doing a google search and finding a post in your forum that was similar to my issue.
 
On 9/20 morning my browser was acting strange like when I clicked the arrow to go back I had to click numerous times and sometime it wouldn't go back at all.   I was running Kaspersky anti virus at the time but wonder if something malicous got in.   When I shut down the computer and tried to restart it took almost 90 minutes to start .  Once it starts and I click start menu or a program on the desktop the it hangs and I'm able to do nothing. 
 
 
I'm able to work in safe mode and safe mode with networking as normal.
 
As recommended.
 
I downloaded super anti spyware and it found only cookies I got rid of .
 
I also downloaded Adware cleaner which found a number of issues which I deleted.
 
Did a malware bytes scan and said I was clean. Tried to start in normal mode and the same issues.
 
 
I'd appreaciate any assistance. Thanks!!
 
 
I'd also like to add trying to use system restore to go back further than the morning of 9/20 but the box in the lower left is missing.  I just used that weeks ago and the box was there when I replaced a video card.
 

A:Vista runs fine in safe mode , slow in normal.

Welcome aboard   Download Security Check from here or here and save it to your Desktop. Double-click SecurityCheck.exe Follow the onscreen instructions inside of the black box. A Notepad document should open automatically called checkup.txt; please post the contents of that document.NOTE 1. If one of your security applications (e.g., third-party firewall) requests permission to allow DIG.EXE access the Internet, allow it to do so.NOTE 2 SecurityCheck may produce some false warning(s), so leave the results reading to me. Please download Farbar Service Scanner (FSS) and run it on the computer with the issue.Make sure the following options are checked:
Internet ServicesWindows FirewallSystem RestoreSecurity Center/Action CenterWindows UpdateWindows DefenderOther ServicesPress "Scan".It will create a log (FSS.txt) in the same directory the tool is run.Please copy and paste the log to your reply. Please download MiniToolBox and run it.Checkmark following boxes:Report IE Proxy SettingsReport FF Proxy SettingsList content of HostsList IP configurationList Winsock EntriesList last 10 Event Viewer logList Installed ProgramsList Devices (do NOT change any settings here)List Users, Partitions and Memory sizeClick Go and post the result. Download Malwarebytes' Anti-Malware (aka MBAM): http://www.malwarebytes.org/products/malwarebytes_free to your desktop.* Double-click mbam-setup.exe and follow the prompts to install the program.* At the end, be sure a checkmark is placed next to Up... Read more

Read other 5 answers
RELEVANCY SCORE 146.8

I'm not sure what causes my BSOD. The errors range from BAD_POOL_HEADER to ntfs.sys to drivers-something.

I am currently running Safe Mode with Networking and things seem stable.

I ran Anti-malware (nothing found), VIPRErescuescanner (nothing), fakereanfix (didn't help), ComboFix (probably made things worse).

Are my drivers up to date? No, probably not, but at this point, I'm scared to change anything else.
Is my windows 7 up to date? No updates installed since Jan 2012, I'm too scared to update anything lest I cause more BSODs.

Minidump attached in next post.

A:BSOD in normal mode (various errors), Runs fine in Safe Mode

minidump per SF_Diagnostic_tool

Read other 8 answers
RELEVANCY SCORE 146.8

Honestly, I really don't know where to begin. Every time I try to run my computer in normal mode it restarts and gives me options to run in different safe modes or try normal mode again. My computer runs perfectly fine in safe mode. I haven't added any new programs. It's been this way for some time. I'm currently running sfc /scannow to see if this helps, which I seen it helped on a similar forum on bleepingcomputer. If anyone has anything else to contribute, please feel free.

A:Computer runs fine in safe mode but restart when run in normal mode

This is what it's telling me.

Read other 3 answers
RELEVANCY SCORE 144.8

Hello everyone.  I am trying to fix my mom's computer but have so far been unable.  The laptop is running but it is incredibly slow.  When I first got on it a bunch of pop ops took over the screen.  The computer would randomly go to other sites on it's own.  It would go to a search sight called "clarosearch".  Worst of all, it's incredibly slow.  For example, from the desktop, it take about 45 seconds for the IE window to open when I click on the icon.  It takes about that long to navigate to a page and so fourth. I downloaded and ran a registry cleaner, spybot search and destroy, malwarebytes, and ad-aware.  These found a bunch of problems and cleaned some up, I guess.  The pop ups are gond and so is the strange search site, but the computer is still running just as slow.  It's a paperweight.  Getting another computer isn't really an option right now as my mom is unemployed and we're actually trying to get her resume online but we can't even do that right now with the way the laptop is acting.  I downloaded hijackthis and ran a scan.  Here is the log.    Oh, and as the subject says, the computer runs fast and fine in safe mode.  Please let me know if there is any other info that is needed as I'm not sure what to provide.  Thank you in advance for any help or suggestions you can provide.  Logfile of Trend Micro HijackThis v2.0.4Scan saved at 6:26:57 PM, on 4/26/2014Pl... Read more

A:Windows XP Laptop very slow in normal mode but fine in safe mode

Hello scoobyjax,my name is Jo and I will help you with your computer problems.Please follow these guidelines:Logs can take a while to research, so please be patient.Read and follow the instructions in the sequence they are posted.print or copy & save instructions.back up all your private data / important files on another (external) drive before using our tools.Do not install / uninstall any applications, unless otherwise instructed.Use only that tools you have been instructed to use.Copy and Paste the log files inside your post, unless otherwise instructed.Ask for clarification, if you have any questions. Stay with this topic til you get the all clean post.My first language is not english. So please do not use slang or idioms. It could be hard for me to read. Thanks for your understanding.***1. Download Security Check by screen317 from here or here.Save it to your Desktop.Double click SecurityCheck.exe and follow the onscreen instructions inside of the black box.Vista / Windows 7/8 users right-click and select Run As Administrator.A Notepad document should open automatically called checkup.txt; please post the contents of that document.***2. Download OTL to your desktop.Double click on the icon to run it.Vista / Windows 7/8 users right-click and select Run As Administrator.Make sure all other windows are closed and to let it run uninterrupted.When the window appears, underneath Output at the top change it to Minimal Output.Check the boxes beside LOP Check and Purity Check... Read more

Read other 3 answers
RELEVANCY SCORE 137.2

Hi,

About two months ago my HP Pavilion 6654y Win7, 8GB, etc.,
started running extremely slowly in Normal Mode. It takes several minutes to respond to mouse clicks, etc.
Basically, it just hangs. But it runs "ok" for a minute or two while still rebooting.

In Safe mode it runs just fine.
I've tried everything I can think of to narrow down the problem, to no avail,
including numerous scans such as AVG, Malwarebytes, Trend Micro Housecall.
Installed UnHackMe to check for rootkits. Even got Reimage and ran it several times.

I've used CCleaner to clean things up, and also to clear out Startup programs
and disable most scheduled tasks, as follows,
(though it is confusing to me since I still see some of the process when started up in Normal Mode):

Yes HKLM:Run StartCCC Advanced Micro Devices, Inc. "C:\Program Files (x86)\ATI Technologies\ATI.ACE\Core-Static\CLIStart.exe" MSRun
Yes HKLM:Run KillProcess Orange Lamp Software Solutions "C:\Program Files (x86)\KillProcess\KillProcess.exe"
Yes HKCU:Run HydraVisionDesktopManager AMD "C:\Program Files (x86)\ATI Technologies\HydraVision\HydraDM.exe"
No Startup User Stickies.lnk Zhorn Software C:\PROGRA~2\Stickies\stickies.exe
No Startup User OpenOffice.org 3.3.lnk C:\PROGRA~2\OPENOF~1.ORG\program\QUICKS~1.EXE
No Startup User 1-Click Answers.lnk Answers Corporation C:\PROGRA~2\1-CLI... Read more

A:Win7 fine in Safe Mode, extremely slow responses in Normal Mode.

Please run Minitoolbox and include the List Installed Programs. Check HP desktop if it comes with a diagnostic test within windows or BIOS utility for memory sticks and hard drive and try running the complete test. Please post back if there are no such features as they would be provided. Try also doing some house cleaning for some dust and bunnies to make sure thermal events is not contributing to the problem.

Read other 11 answers
RELEVANCY SCORE 136.8

Hey guys I've checked through some of the tuts and what-not on this forum and still can't find a way to get me out of trouble..
i turned my computer on yesterday (23rd September) and there was an automatic update. Ever since the update my computer has been extremely slow (will take several minutes to open firefox -or anything for that matter). I booted safe mode and it's running fine. I opened up msconfig and did a clean boot but the problem was still there.
It's a fairly new build and I was stupid and forgot to get a virus protection i can't install it in safe mode either..

Can anyone help?
-cheers

A:Explorer running slow in normal mode, fine in safe mode.?

Windows Defender Offline

Read other 9 answers
RELEVANCY SCORE 136.8

Hello, the computer I am concerned with is running Windows 7 with IE8, Microsoft Security Essentials and Malwarebytes Anti-Malware. I am currently in Safe Mode with Networking without issue.

The owner of the computer says that something happened earlier today while he was online that sounds like some false antivirus popup, but he's unsure. Here are the symptoms in normal mode. Every application, from moving through them to opening and closing them, runs exceptionally slow - one to three minutes to open, at least a minute to open internet pages. I noticed that, when in IE, as the pages are loading the IE page disappears and reappears. I am not very familiar with Windows 7 so I don't know if it is related. The computer seems to be getting slower as the day goes on. CPU usage is very high.

So far, I have disabled many startup items that were unnecessary. I ran CCleaner and cleaned up. MBAM was run in both normal and safe mode, full scans, and found nothing. This is also posted in Viruses and Malware, but I'm unsure where it should live.

If you can help, thanks!! I have to work on the Win7 computer from LogMeIn, and may have to get around in safe mode there.

A:Win7 runs extremely slow in normal mode, but nicely in safe mode

I suggest you wait for a response from the malware specialists before looking elsewhere.

Read other 2 answers
RELEVANCY SCORE 136.4

Can someone help me to figure out what is making this happen ? its driving me nuts, my cpu usage goes through the roof, and I am clueless as to what is causing this... but in safe mode with networking it runs fine.... can someone help me ??? many thanks!!!!

Read other answers
RELEVANCY SCORE 133.6

Hi, after connecting and disconnecting some external HDD using USB to my pc, BSOD keeps showing constantly after 5 minutes from booting to windows .

I checked RAM, and it urned out to be in good shape, then i tried Registry cleaning, but nothing changed .

It works very well and stable under safe mode only, and my best guess that it's my HDD which is not in good shape, but that doesn't explain how it works fine under safe mode, it supposed to crash also, right ?

I have :

Pentium 4 3.00 GHz
4 GB RAM
Nvidia 8400GS

OS : Windows 7 Ultimate 64bit
Sorry for my bad English

A:BSOD in normal and clean boot, runs fine in safe mode

Here is my SF_Diagnostic_Tool results

Read other 5 answers
RELEVANCY SCORE 131.6

I'm not sure what is going on. I haven't tried much but I'm not very good with BSODs.

Minidump is going to be posted and so is msinfo32...

Help is vastly appreciated.

One attachment is a minidump other is msinfo32.

Edit : A little more info, this happens after typing in my password to boot to desktop. Pool Corruption shows up in one of the minidumps, but not this one or the other two. I think it has to do with drivers but I'm not certain.

A:Computer BSODs in Normal, Fine in Safe Mode+Networking

If I posted something wrong please let me know. I didn't see the post about that other program to run till i had already posted. Regardless it wont let me run it. D:

Read other 2 answers
RELEVANCY SCORE 131.6

Hey people, I hope you can lend me a hand.

As the title suggest, I've got a problem with the internet. I found a similar thread in which the problem was found to be Norton, so I followed the steps and removed it using the remover tool but it was to no avail.

I have also looked at the processes on msconfig in safe mode and applied them in normal but this wasn't successful. I also read it could be a problem with the IPSEC Services, which I have now disabled but the problem persists.

Just wondering if you had any ideas and if I need to post any screenies etc.

Cheers,
Rupert

A:Internet Fail in normal, fine in safe mode with networking

Just to be sure,
this is what you did
How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
and the computer did not work properly.

Read other 9 answers
RELEVANCY SCORE 130.8

Hi,

I got win 7 home premium 64 bit on an i3 laptop. My system worked fine until today morning.

The problem is this;
When I boot the system in normal mode, I get to the part where I need to enter my password to login. Once i do that, all I get is a black screen with the mouse pointer that moves about normally. I've waited for the normal desktop environment to appear (ie icons and taskbar) but this doesn't happen (btw, my desktop background color is always black).
The system boots perfectly in safe mode.

Yesterday was the first time in over a year I used utorrent. I used to get the BSOD when I used to use it. I couldn't rectify the problem and hence had stopped using it. It worked fine yesterday though.

Any idea whats happening and how I could fix the problem?

A:Windows doesn't login properly in normal mode but fine in safe mode

I've tried running SFC /SCANNOW a couple of times but I keep getting a message that there may be corrupted files. I also created the sfcdetails.txt file.
Going to try the system restore option now

Read other 6 answers
RELEVANCY SCORE 130.8

After upgrading to SP2 about a month ago so I could take finals on my computer at school, i noticed that my computer wouldn't boot up in safe mode (i just get a blank dark screen and i can hear the computer doing something but giving it a reasonable amount of time it doesn't progress from that screen). It didn't concern me because normal mode was working and i was able to take my tests. But now I want to get to the bottom of this. I delayed getting sp2 because i had a feeling it would mess up my computer. (i've had other problems too with visual skins but i was able to resolve those).If it matters, i ran a scan of my system with spyware doctor and it said i had a trojan.dialer and needed to boot in safemode to get rid of it. When I tried, it wouldn't load. Oh, btw, any way to get rid of that trojan.dialer without using safemode?

A:Windows Xp Home, After Sp2, Safe Mode Doesn't Work, Normal Mode's Fine?

Try running Ewido online scan and post the results overhere.

Read other 6 answers
RELEVANCY SCORE 126.8

So a few nights ago, there was a bad storm. I turned the computer off manually (by holding the power button in) and unplugged it before the storm hit. When I turned it back on, I noticed that it was taking around 20 minutes to start up. When it gets to the point where I can open programs, it takes them forever to respond. At first I thought this was related to the storm or the way I turned the computer off. I took out the CMOS battery and let that sit for a while, thinking that might have been a problem, but it wasn't.

At this point, I'm thinking it's coincidental that this happened right when the storm hit and the problem is actually malware or something.

I have the latest version and updates for AVG, but it didn't find anything on a full computer scan. Does it sound like there's something I should be able to do?

A:Vista runs fine in safe mode, VERY slow otherwise

Hello ElectroSpecter,My name is swagger and I'll be assisting you.Could you tell me what OS you are running?regards,swagger

Read other 12 answers
RELEVANCY SCORE 124

Last Sunday my computer froze so I had to do a hard shutoff...when I turned it back on I got BSOD. I can't remember what exactly the stop error was. Point is whatever was wrong with my puter I couldn't even get as far as the splash screen and safe mode wouldn't load. I went down and bought Windows 7(x64) (I was running Vista x64). Since I wasn't able to get into windows I had to set it up to boot from the disk first upon startup. Having done that it took everything I had off and just replaced it with Win7. I thought everything was going to be okay. I downloaded the critical Microsoft updates and I think my drivers are up to date. I installed and activated my anti-virus. My system is running SO slow it hangs and before I turned the "auto restart upon error function" off it was constantly telling windows Explorer had some error and my computer puter would restart in one minute. I hardly have anything on here so I am not sure what is causing the problem. Pretty much works just fine in Safe Mode. I can browse the net, play some online based games and video is fine (even if I can't hear sound in safemode). Please help me fix whatever is going on....Thank you so much..*Edited to add: I found this.. Processor-Intell Core 2 Duo CPU [email protected] 2.26 GHz 2.26 GHz Ram- 4.00 GB Graphics- Nvidia GeForce 9800M GTS 1 GB.If there is anything else you need please tell me what it is and where to find it and I will get it up asap. Thx again.*HJT LOG:Logfile of Trend Mic... Read more

A:BSOD's, Hanging OS, SLOW performance...but runs fine in Safe Mode

I have 4 pages in a small notebook full of error messages that I have received since posting the OP....I have since tried to reinstall the new Windows 7 from disk, but that hasn't helped. I can't get my laptop to do much of anything now, including in safe mode. I was able to finally run the start up repair option after getting the following message on this morning's start up:QUOTESMART Failure Predicted on Hard Disk 0:WDC WD3200BEKT 22F3TO-S1 Immediately back up data and replace your HDD. A failure may be imminent. The Start up Repair said, QUOTERoot Cause- Bad Hard DiskSo unless you have any other advice I am going to go down and buy a new HDD today. This is way over my head and I really don't want to get the run around when I am having to spend as much money as I am. I just want to be 100% sure that a BAD HDD is REALLY the problem.Thanks to anyone who picks up this lost cause...

Read other 3 answers
RELEVANCY SCORE 123.2

Hi guys,
it is my first time to join to this forum. I really need the solution of my laptop Problem. I Have my
Gateway EC38 and it has been
freezing while I am using in normal mode.
But in Safe Mode works well. I tried uninstall my video card driver and also my sound card but nothing works. I also do
sfc/scannow in safe mode/safe mode with command prompt, but yet it says I have corrupted file but he doesnt show any file. I check in log file but I dont understand much.
Im always maintaining my laptop hardware status specially ventilation and change every year the cpu thermal gel.
Please help me find solutions to this kind of problem.
My Laptop Details:
Windows 7 64bit
x64 Base processor
factory OS windows Vista
Processor: Intel Centrino 2

Read other answers
RELEVANCY SCORE 123.2

laptop has been randomly freezing. cursor disappears no keyboard function. only thing to do is manual shutdown.

Now getting a BSOD error 50.

any help?

A:BSOD BCCode 50. freezes in normal mode, works fine in safe mode

Code:
BugCheck 50, {fffff80040f9e3b0, 1, fffff80000b9a1aa, 5}

*** WARNING: Unable to verify timestamp for ntoskrnl.exe
*** ERROR: Module load completed but symbols could not be loaded for ntoskrnl.exe

Could not read faulting driver name
Probably caused by : ntoskrnl.exe ( nt_fffff80000b95000+51aa )

Followup: MachineOwner
---------
Your crash dumps are not showing any finite probable cause. In such a situation, it is better to enable Driver Verifier to monitor the drivers.
Driver Verifier - Enable and Disable
Run Driver Verifier for 24 hours or the occurrence of the next crash, whichever is earlier.



   Information
Why Driver Verifier:
It puts a stress on the drivers, ans so it makes the unstable drivers crash. Hopefully the driver that crashes is recorded in the memory dump.

How Can we know that DV is enabled:
It will make the system bit of slow, laggy.



   Warning
Before enabling DV, make it sure that you have earlier System restore points made in your computer. You can check it easily by using CCleaner looking at Tools > System Restore.

If there is no points, make a System Restore Point manually before enabling DV.



   Tip

If you fail to get on the Desktop because of DV, Boot into Advanced Boot Options > Safe mode. Disable DV there. Now boot normally again, and try following the instruction of enabling DV again.
If you cannot boot in Safe mode too, do a System Restore to a point you made ... Read more

Read other 9 answers
RELEVANCY SCORE 122.8

Hey,

I am having a problem with a laptop, I am getting a blue screen when starting in normal mode, but if I start in safe mode it starts up and logs in fine.

I am not being told what is causing a problem, just to uninstall any new programs/hardware, but nothing has been installed at all.

Does anyone know what could be causing this?

Thanks for any help :)

A:Starting up fine in safe mode but blue screen with normal mode

Go here Windows Vista/7 BOSD Posting instructions follow all instructions to the letter, using all tools illustrated. Then proceed to the next steps by posting your logs. Keep your posts and logs (logs mini dumps etc...) in BOSD, App crashes, and hangs.

Be patient they get a lot of inquires. Someone will be along to help you.

Read other 1 answers
RELEVANCY SCORE 122.8

My Toshiba satellite will only boot in safe mode tried sfc/scannow getting this message

Windows resource protection found corrupt files but was unable to fix some of them.

I've tried a system restore but that wasnt very successful either, if I uploaded the CBS log of the scan could someone try help me with the problem. Thanks

A:BSOD when trying to boot in normal mode, safe mode works fine

You may need to run SFC up to 3 times for it to have a chance to repair all files.

If it won't then you can consider a Repair Install.

However be aware that factory preinstalled Win7 is one of the worst possible installs of Win7 one can have, larded with bloatware and duplicate utilties that intefere with better versions built into Win7. So I would strongly consider doing the vastly superior Clean Reinstall - Factory OEM Windows 7.

If you decide to try to repair you can also capture the BSOD file and post it up for one of our BSOD analysts as shown here: Blue Screen of Death (BSOD) Posting Instructions - Windows 7 Forums

Read other 3 answers
RELEVANCY SCORE 122.8

Hello,

From last 2 days I am facing constant crash in windows 7 normal mode (Lenovo notebook G580). but when I do boot the pc in safe mode with networking, crash never occurs. I am posting this thread in safe mode only from the same laptop. I have dmp file generated using verifier. and the same with provided exe here. I will try to upload both. I think some driver is causing the crash but can't find which one. please help to resolve this as I hope must not be the hard disk issue.

A:PC working fine in safe mode but crashes (BSOD) in normal mode

  
Quote: Originally Posted by amitshahc


I think some driver is causing the crash but can't find which one.


The thread title gives the exact impression. And it was a good step to enable verifier.

Now disable verifier.

Then ....
Update the SplitCam product: SplitCam free webcam software for video streaming and adding cool webcam effects

Free up the startup. Windows does not need any other program to auto start with it, but the auto start programs often conflicts and causes various problems including BSODs.
Click on the Start button
Type ?msconfig (without quotes), click the resulting link. It will open the System Configuration window.
Select the ?Startup? tab.
Deselect all items other than the antivirus (MSC) and the touchpad driver SynTPEnh.
Apply > OK
Accept then restart.
Then run the laptop normally. Let us see any further BSOD crash dump after doing it.

Read other 1 answers
RELEVANCY SCORE 122.8

Everytime i open my pc up in normal mode, it seems to restart itself within a few seconds to a few minutes, It tends to happen when i open up a program like Chrome. I',m currently on safe mode with networking and have done registry cleaners, updated video card drivers and looked for viruses, yet nothing has seemed wrong, I've also done a system restore to when my pc was working fine, but it still was happening, I saw on another post here that i should post my msinfo32 so here you go, Thanks.

A:BSOD only occurs in normal mode, Works fine on safe mode.

Just tried opening in normal mode again, got a blue screen within 2 minutes. Didn't open chrome, only programs i had opened was mozilla firefox, and startup programs

Read other 6 answers
RELEVANCY SCORE 122.8

Not sure what I have stumbled upon here. Was trying to download some music from SugarSync that I had from another PC, realized I did not have a music player installed and tried to download VLC and that's when things went bad.
 
I had run my Anti-Virus (Avast ) and it found nothing,
I just now opened it (in safe mode) to obtain the official name/version and found it to display a large red banner declaring I am unprotected and the Avast service turned off.
None of those controls on that panel work 
 
Am assuming some infection did this as I did not turn it off!
When I clicked Scan it displays "Unable to start scan. There are no more endpoints available from the endpoint mapper"
 
This is an Asus G73JW Laptop
Windows 7 SP1
I use
Avast Internet Security
Spybot S&D
CCleaner
 
Any Idea as to what I have run into here?
 
Thanks,
 
 
 

A:Fine in Safe mode, but in normal mode, icons and Startmenu don't work

Have you performed a System Restore recently?
 
Download your version of Avast, but don't install it yet.
 
With the computer offline use the Avast uninstall utility to uninstall your current installation.
 
Once you have uninstalled the old version, install the version you downloaded.

Read other 2 answers
RELEVANCY SCORE 122.8

My speedtest.net performance is 30 Mbps download, and between 0.3 and 2.0 Mbps upload. If I start in safe mode with netorking, I get download and upload speeds of 25-30, my contracted speeds. Obviously, something loading in the full mode interferes with upload speed. I have tried restarting in safe mode with all of the items checked in the services and programs tabs in msconfig, and still get excellent up and download speeds. How can I figure out what is interfering with my upload speed in normal mode, but not in safe mode?

A:Poor upload speed in normal mode, fine in safe mode

Use msconfig to determine what is causing the problem

How to use msconfig in Windows 7

Click on Start then Run, type msconfig and press Enter.
Click on the Startup tab, record what is currently starting then click the Disable All button.
Reboot and see if it runs better.
If yes then use msconfig to enable several items at a time till you find the culprit.

If no, start msconfig and click on the Services tab.
Check the Hide All Microsoft Services box, record what is currently starting then click the Disable All button.
Again, do a regular boot, see if it runs normal.
If yes then use msconfig to enable services till you find the culprit.

Once you've found the culprit, uninstall it or find out how to eliminate it from your system. Simply disabling it in msconfig is a temporary fix at best.
Enable everything else you disabled.

Read other 6 answers
RELEVANCY SCORE 122.8

Hi guys,

I am having this problem since couple of days, my wireless internet connection is working fine i can go in my messenger but i cant browse any websites at all in normal mode.. i tried piniging these websites it comes back fail. but it works totally fine in safe mode, pls pls help me out as I have to study for my exams.

Thanks guys
Sunny
 

A:My internet not working on normal mode but works fine in safe mode PLS HELP

Read other 10 answers
RELEVANCY SCORE 122.8

I have a computer that would not see the hard drive a few days ago. Got a new hard drive and did a clean install of windows and restored the rest of the files with Carbonite. A few days later the computer would not boot into windows again. So this time i reformatted the new drive and stuck it into an identical PC I had.

Now its been 3 days and the computer started to run EXTREMELY slow after booting up. In safe mode its perfectly fine. I have ran multiple virus scans from malware bytes, avast and superantispyware, nothing found.

After some trial and error with turning services off I found that if i disable the local area connection in safe mode then boot into windows normally it runs fine(without the internet connection of course). I have brought the PC to a different location and even put the hard drive in the original computer and it is still having the same issue.

Any ideas on what i can try?

A:Running slow with network connection enabled, runs fine in Safe mode

Welcome !
Is the PC very slow right away after a cold boot or does it happen over a certain amount of time?

Download | Process Explorer.

Immediately after a Cold Boot launch Process Explorer (if you have a short list,
click "Show Processes From All Users" the right most option in the top bar):
Arrange "Working Set" (by clicking on the top of that column) Take a screenshot.
Arrange "Private Bytes" (by clicking on the top of that column) Take a screenshot.
Arrange "CPU" (by clicking on the top of that column) Take a screenshot.

After 30 minutes (or the maximum amount the system hold its self together):
Arrange "Working Set" (by clicking on the top of that column) Take a screenshot.
Arrange "Private Bytes" (by clicking on the top of that column) Take a screenshot.
Arrange "CPU" (by clicking on the top of that column) Take a screenshot.
Upload the screenshots in a .zip file arranged in folders please.

Read other 9 answers
RELEVANCY SCORE 122.8

I am using Windows XP home edition with SP3. It was working normally. I used to get a popup "Windows cannot find "syssetup.exe"....When i opened yesterday morning I found it taking longer and never go to the desktop after giving the username and password. It stops at Welcome screen with a msg "Loading your personal settings" and no more response. I followed below steps to trouble shoot the issue.

1.I have tried opening in both "safemode" and "safemode with networking", found its working fine. I ran "msconfig" in safemode and unchecked some unwanted applications(nothing related to windows process) and tried again opening in normal mode.... Not worked

2. My internet works normally in safemode. Found some virus by running antivirus in safemode and cleared all the viruses.

It would be really appreciable if any one could solve my issue..

Cheers!

A:XP home stops loading at Welcome Screen in normal mode, but working fine in Safe mode

try using system restore in safe mode...it might help...or try selecting the last known good config that worked...if still not work...try repairing it with you windows xp bootable cd..

Read other 2 answers
RELEVANCY SCORE 122.4

Hello everyone. I have a Compaq SR1954NX Desktop computer that I recently reformatted and installed Windows XP Pro SP3 on. After installing some games and applications, a few days later I shut the computer off for the night. Upon the next morning my USB Mouse, a Creative Fatal1ty 1010, stopped working on it. If I unplugged it and plugged it in a different USB port, it would say "Found device, Creative Fatal1ty Mouse, Your Device is now ready to use." However it still would not do anything. However, upon entering safe mode, it works fine.

I reformatted after this, as I thought it was my mistake, and had only installed one or two small games. However, it just happened again.

Can anyone here help me with this? Thanks in advance.

Read other answers
RELEVANCY SCORE 122.4

I started having said problem during virus removal.
I had removed multiple virus via malware, SAS, aSquare, combofix, and, I could not connect to any websites.
Via my wireless connection, windows said my signal strength was good and it was connected to the wireless network.
I tried pinging different websites like yahoo.com, google.com, etc and all my requests timed out.

So I decided to trouble shoot.
Booting into safe mode w/ networking worked fine. I was able to ping and connect to websites via Internet Explorer.
I ran SpybotS&D, and it removed a win32.agent and some sort of malware that had firewall in the name... forgot exactly what it was, and I don't have the log on hand.
Anyways, after this removal I tried again to ping website like yahoo.com, google.com, etc, and the ping worked fine.
However, I still could not connect to any websites via Internet Explorer. I tried reinstalling IE, but its the same story.
During this whole process, I have been able to use Internet Explorer succesfully only in safe mode.

Any ideas? I doubt it is a virus directly causing my problems. It's had a thorough cleaning. Maybe some left over wreckage?
I doubt its a firewall issue. CA's personal firewall is installed on the machine. I know CA antivirus is running in safe mode, I'm not so sure if the firewall does or not. I'm assuming it does.
I don't know where to even start on this. Any help would be appreciated.

A:Can't browse in normal mode, works fine in safe mode.

Hello,You should not browse in Safe Mode because your security programs do not function in safe mode which means that more malware finds its way onto your computer.This issue is related to the issue you have posted here: http://www.bleepingcomputer.com/forums/t/240716/sdra64exe-uacinitdll-fakealert-vundo/ Because you have this log posted, you should NOT make further changes to your computer (install/uninstall programs, use special fix tools, delete files, edit the registry, etc) unless advised by a HJT Team member, nor should you ask for help elsewhere. Doing so can result in system changes which may not show in the log you already posted. Further, any modifications you make on your own may cause confusion for the helper assisting you and could complicate the malware removal process which would extend the time it takes to clean your computer.From this point on the HJT Team should be the only members that you take advice from, until they have verified your log as clean.Please be patient. It may take a while to get a response because the HJT Team members are EXTREMELY busy working logs posted before yours. They are volunteers who will help you out as soon as possible. Once you have made your post and are waiting, please DO NOT make another reply until it has been responded to by a member of the HJT Team. Generally the staff checks the forum for postings that have 0 replies as this makes it easier for them to identify those who have not been helped. If you post another response ... Read more

Read other 1 answers
RELEVANCY SCORE 122.4

Recently purchased this all in one PC on second hand. It initially had Windows 7 Home Premium 64 bit Japanese OS. I installed Windows 7 Ultimate 32 bit English OS after purchasing and installed the Drivers from the DVD which came along with the PC. Ran windows update till date. But got BSOD many times. Thinking of Hard drive issue, changed the hard disk first time with another used one and next time with newly purchased one.

All the time installed Windows 7 Ultimate 32 bit English OS and installed the Drivers from the DVD which came along with the PC. Ran windows update till date. But in all 3 hard disks getting the BSOD error.

Installed Microsoft Security Essentials each time and checked for virus. Ran Dell Diagnostics downloaded from Dell website and found no issues.

Got "Session "Microsoft Security Client OOBE" stopped due to the following error: 0xC000000D" error on Event viewer many times. After searching some forums deleted MSE.

Ran the SF diagnotic utility and uploading the file for your reference.

Please help me to overcome this issue.

A:BSOD in Normal mode but works fine in Safe mode

Attachment in the first thread gauti2009.zip is SF Diagnostic Tool run in Safe mode.
Attachment in the current thread SF_02-09-2013.rar is SF Diagnostic Tool run in Normal mode. (Somehow no BSOD during this short time, able to get the file and post it).

Hope this will help.

Read other 2 answers
RELEVANCY SCORE 122.4

2 days ago my computer randomly froze up when I had a few chrome windows open and a few other applications. The mouse can move around but nothing on the screen is responsive. I figured it was a one time thing and forced shut down and rebooted. It again froze up about 3 minutes later and now every time I use it it freezes from within a few minutes of logging in to up to an hour. Even if I just log in and don't touch anything it will freeze at some point in time. Last night I used it for 6 hours and thought everything was fixed but when I woke up it was again frozen. It also seems to be lagging a little when opening new tabs and applications which it never did. It works fine in safe mode and stayed on for over 24 hours with no problems.

Dell Vostro laptop
3ghz 2GB RAM
250GB HD 50% full

What I have done:

Restored to a date of last week when everything was working - didn't help
Ran updated versions of AVG and Malwarebytes - clean and didn't help
Turned off all start up items in MSCONFIG - didn't help
Turned off all non microsoft services in services in MSCONFIG - didn't help
All the drivers in my device manager seem to be working as I see no exclamation points or anything

I googled around and tried to figure it out on my own but can't seem to figure it out so if anyone has any ideas I would love to hear them. If you need any more information please ask and I will provide. Hope it was clear and concise.

Thanks

A:XP freezing in normal mode working fine in safe mode

Please check the Event Viewer to see what errors are showing up at these times. Each error has a date and time.Go to Start> Run and type in eventvwr.msc then press Enter.When the Event Viewer opens click on Applications in the left pane. If you double click on an error a description of the error will open. Click on the copy icon, (the copy icon is highlighted with the red square in the picture below), once this is done you can right click and paste this description. Please post the error description/s in your next post in this topic.

Read other 7 answers
RELEVANCY SCORE 122.4

I have a HP Pavilion A6352c desktop pc. I have recently installed a clean copy on win 7. I have listed the issue I am having below. I hope you can assist me in getting this system to a stable state.

1. System locks up running in Normal Mode - I will take about 3 minutes before the entire system locks up, I have to do a hard shutdown when this happens. I can start the system in Normal mode, but only if I use the diagnostic startup option in MSConfig. I can enable some services, but I am in the process of trying to figure out which one is making it lockup.

2. The system will run fine under safe mode with networking and such. I have the normal startup option in msconfig enabled in safe mode and no issue except it's in Safe Mode!

I have attached the requested documents/files in the attached zip file. I was unable to get the Perfmon report.

I look forward to your response.

Thanks in advance

SCA

A:Systems runs in safe mode - Normal mode locks up

The dumps are all over the map, but they all are having issues in amdk8.sys (the OS's CPU driver). What's really interesting is one of these dumps looks almost exactly the same as the issue that is documented in KB 975530, but that's for Intel CPUs running hyper-v. However, you *are* running into a watchdog timeout on the CPU (it's causing other drivers to crash and confuse analyze, but it's not that code's fault that the CPU stopped processing it's requests). This means you might have a bum core on that CPU when entering/exiting C-states. Try running this:
reg add HKLM\System\CurrentControlSet\Control\Processor /v Capabilities /t REG_DWORD /d 0x0007e066

Reboot, and see if it still causes problems in regular boot mode. Either way, you probably need to have that CPU looked at as a potential bad part.

Read other 9 answers
RELEVANCY SCORE 122.4

Hi,

I'm having problems when I load windows in normal mode. When I turn on the computer everything starts as normal. It's after clicking my name and the desktop loads, nothing responds. It just freezes.

I have no problems when loading windows in safe mode with networking.

I ran a full scan through my virus software, Kaspersky. No threats were detected.

I also tried System Restore twice while in safe mode. I'm still having issues.

Any help would be greatly appreciated. Thanks so much!
 

A:Solved: Pc freezes in normal mode, but runs in safe mode

Read other 16 answers
RELEVANCY SCORE 122

Hi
I have Thinkpad T43, with windows XP professional.

Since few days whenever i launched my ATI catalyst control center I would get BSOD and laptop will boot automatically and then everything would be fine.

Then while browsing my wife downloaded some media player exe, and since then my IE was redirecting to unknown sites (xalab etc) not to mention various ad pop-ups. One of the online video sites gave a message that I have TROJ/Rustok-N. (Also I would like to mention since couple of months my System Restore was not working although everything else was working fine)

I ran spybot, malawarebytes, trojanremover and removed whatever was reported. But the problem persisted, so I renewed my Norton Internet Security (actually got Norton 360), ran scans but it couldnt find anything.

Then I booted in safe mode and ran all these again, last thing I remember trojanremover prompted to remove something like sv~.exe and i did, when i restarted the system in normal mode I got BSOD and laptop rebooted, I disabled automatic restart on failure but it keeps on doing that.

I then went to Access IBM and restored by configuration which brings back the system files to previous state (the most latest point available was 07/2006)
I still got the BSOD while booting into normal mode, but safe mode was working fine.

I then went into safe mode and disabled couple of services on startup, then my laptop booted fine in normal mode, I found that now windows xp was reset to SP2, so i ran windows update w... Read more

A:BSOD 8E while booting into normal mode, Safe mode fine. Disable automatic restart doesnt work.

FWIW: http://kadaitcha.cx/xp/stop_error.htmlAs stated, it's a matter of hide-and-seek, with no guarantee of finding the culprit.Another link that may be useful: http://aumha.org/a/stop.htmLouis

Read other 1 answers
RELEVANCY SCORE 121.2

normal mode takes 30 mins to load Firefox, all programs continually freeze  every couple of mins, took 2 hours to start eset online scan.
Safe mode is fine, i went to msconfig and selected only ms starup and problem still remains
 
can anyone help??
 
I've used this site for amazing work before, any ideas?
 
I'm in safe mode at the moment as its the only way my system works., I've ran malwarebytes, spybot and in the middle of running eset online scanner
 

A:Win 7 64, safe mode fine normal mode unuseable

Please download MiniToolBox  , save it to your desktop and run it.
 Checkmark the following checkboxes:  List last 10 Event Viewer log  List Installed Programs  List Users, Partitions and Memory size.
 Click Go and paste the content into your next post.
 Also...please Publish a Snapshot using Speccy - http://www.bleepingcomputer.com/forums/topic323892.html/page__p__1797792#entry1797792 , taking care to post the link of the snapshot in your next post. 
Louis

Read other 2 answers
RELEVANCY SCORE 121.2

Hello guys,
you are my last hope! I do not know what I am supposed to do anymore, I spent the last 8hours looking on the net what I could do. I am a computer noob and have little experience with computers at all.

Here's my problem. My laptop doesn't start anymore. The first thing I noticed on my boot screen were four parallel vertical lines of dots, then four parallel lines of vertical dashes then dots again and so on. This is in the background from the time when I start my samsung R70, even on the boot screen, as well as on the windows vista loading screen (these little boxes floating from right to left...). These really weird dots are however NOT present in the DOs menu and neither is it after you pressed F8 to boot in safe mode. They are also NOT present in safe mode that means they disappear after the boot screen and are not evident on the black background of the safe mode desktop.
However at the time when the windows vista sign is supposed to flash up and you'd be prompted to enter your password (this is when I start it normally), nothing happens and a greyish-white screen comes up, after which the system just restarts and the whole process happens again (including the dots mentioned earlier). I can run the laptop in safe mode, in fact I am running it in safe mode with network drivers right now to type this, but I cannot, under any circumstances, run it in normal mode. When I start it in safe mode I get the following notice:

(Yes, I am running a German OS, so I a... Read more

A:Help! Laptop runs in Safe mode but not in normal mode

Quote:





Originally Posted by XQlusive



Weitere Informationen ?ber das Problem [Additional information]
BCCode: 50
BCP1: A33100F8
BCP2: 00000000
BCP3: 820818F8
BCP4: 00000002
OS Version: 6_0_6000
Service Pack: 0_0

Please guys, help me!

I am a year 12 boarding student and I desperately need my laptop to get my work done!

Do you guys reckon that installing a completely new windows vista will solve the problem?

- I do not have the original vista CD with me since I am German and on an exchange to Australia. My dad has the CD and he's about 22.000km away right now.




Hi -

The BSOD bugcheck (STOP error) = 0x50 = invalid memory referenced

As you said - no service packs installed, which is probably one of the problems here. You need to see if you can re-install Windows and then see if it is stable or not.

I do recommend another re-install of Vista using the manufacturer's (OEM) recovery DVD. This must be the first item on the "to do" list. Contact your father or the system manufacturer and obtain the Vista recovery DVDs. Do you have a recovery partition? Many do. Usually, the key to invoke the recovery partition if F10 - during boot-up.

Two other options until your Vista DVDs arrive from your father -
1. Download and burn Server 2008 - it has the same build as Vista, with a few features that have been disabled. It is a trial offer that can be renewed up to 240 days - http:/... Read more

Read other 1 answers
RELEVANCY SCORE 120.4

Hello ladies and gents , im having a problem with my emachine T1120. It starts up and goes through the welcome screen then goes to bios settings , I click on "start windows normally" and enter it and the machine runs right back to the original bios screen , cant figure, unplugged and pressed the power button several times plugged in same result, why? I added no new hardware or software just turned it on and wa la

A:Win.xp emachine starts and runs safe mode, safe mode with networking

hello and welcome to BleepingComputer,,
 
     this is reminiscent of BIOS settings that need to be reset to default. you can do this by using that option in BIOS. do you see the option there? 
 
if this pattern exists after BIOS reset, then there are other XP level options to try like console command /sfc scannow and chkdsk /r
 
 not to long ago, i was dealing with a PC that was doing this same thing, and it was the hard drive (SATA) protocol setting in BIOS, it had to be set to IDE.
 
one more thing, this could be blue screen error that isn't halting, just looping boot. is there an option at the boot screen (the one with the safe mode options) about halting on errors?

Read other 3 answers
RELEVANCY SCORE 119.6

Hello, I'm hoping someone would be able to help me resolve this so that I can avoid having to reinstall Windows. Here's the situation: my laptop suddenly cannot boot up anymore; it usually hangs when the "Please wait..." dialog shows up with the text "Windows is starting up...", but sometimes it goes as far as the login prompt, then hangs after I enter my credentials and press Enter. When it hangs I cannot even move my mouse cursor. I can only think of two things I did out of the ordinary that created this mess:
I installed the driver for the Turtle Beach AudioAdvantage Micro USB stick audio card before my PC started hanging. However, after I installed the driver I was forced to reboot, and my computer rebooted just fine.
I closed my laptop's lid to put it in sleep mode while MyDefrag (formerly JkDefrag) was running. I have done this in the past without any issues, but this time when I exited sleep mode my computer was hanging, so I forced a reboot. This trouble started after I rebooted.

I am able to boot up in Safe Mode, but not Safe Mode with Networking, which leads me to think that maybe some network related drivers got corrupted. Some more info on my setup:
I have Windows XP Pro SP3 installed (v5.1.2600)
I have Avira AntiVir and Comodo Firewall installed
I am not using Hibernation
Audio: SigmaTel STAC9751
Graphics: Intel 945 GMS
Chipset: Mobile Intel 945 GMS Express
Netcard: Realtek RTL8101L
Wifi: Intel PRO/wireless 3945

Update 1: ... Read more

Read other answers
RELEVANCY SCORE 119.6

I have tried to run IE7 in normal mode and I always get a "The address is not valid" window. I have a good internet connection and Firefox works flawlessly. I do not have connection problems. If I ran IE7 in Safe Mode with Networking, I can bring up webpages with no problems. I thought that upgrading to IE8 would cure the problem but I am still getting the exact same problem. I have tried checking many things and have tried many suggestions that I have found through web searches but nothing works. Please help!

A:Internet Explorer will work in Safe Mode with Networking but not in normal mode

what firewall do you have

Read other 1 answers
RELEVANCY SCORE 119.2

I have a Windows 7 Laptop (Home Edition) that boots fine in SAFE mode, but takes an extremely long time to boot in normal mode. When it does get into normal mode, it runs so slow it is unusable.
 
I have run Malwarebytes, SuperAntiSpyWare and Spybot S&D (all in Safe Mode - of course) and it doesn't find any issues.
 
What else can I try?
 
Thanks,
Scott
 
 

A:Windows 7 very slow in normal mode, ok in Safe Mode

Download Security Check from here or here and save it to your Desktop. Double-click SecurityCheck.exe Follow the onscreen instructions inside of the black box. A Notepad document should open automatically called checkup.txt; please post the contents of that document.NOTE 1. If one of your security applications (e.g., third-party firewall) requests permission to allow DIG.EXE access the Internet, allow it to do so.NOTE 2. SecurityCheck may produce some false warning(s), so leave the results reading to me.NOTE 3. If you receive UNSUPPORTED OPERATING SYSTEM! ABORTED! message restart computer and Security Check should run Please download Farbar Service Scanner (FSS) and run it on the computer with the issue.Make sure the following options are checked:
Internet ServicesWindows FirewallSystem RestoreSecurity Center/Action CenterWindows UpdateWindows DefenderOther ServicesPress "Scan".It will create a log (FSS.txt) in the same directory the tool is run.Please copy and paste the log to your reply. Please download MiniToolBox and run it.Checkmark following boxes:Report IE Proxy SettingsReport FF Proxy SettingsList content of HostsList IP configurationList Winsock EntriesList last 10 Event Viewer logList Installed ProgramsList Devices (do NOT change any settings here)List Users, Partitions and Memory sizeList Restore PointsClick Go and post the result. Please download Malwarebytes Anti-Malware (MBAM) to your desktop.NOTE. If you already have MBAM 2.0 installed scroll down.Double-click ... Read more

Read other 11 answers
RELEVANCY SCORE 118.8

Hi! I'm just a new here, hope someone can help and give advice here. (Sorry if this is not the right thread to start my topic)

Scenario: (this is my first time to encounter this problem)

While playing facebook games last monday, my computer get BSOD and restarts. After booting up on windows, I found out that my internet connection was gone.I tried to restart but still no connection. I use my laptop and other PC to checked if there's internet and yes they are still connected. I restart my pc again and found out after boot up a message box appear says "No AMD graphics driver is installed, or the AMD driver is not functioning properly. Please install the AMD driver appropriate for your amd hardware"

I did uninstall / install my driver but the message box still prompting after restart.
Still no internet connection.

Anyone experience this?
Sorry for my bad english.

Specs:
Intel i3 2120
Asrock H61 U3S3
Sapphire 7770 OC Edition
500 WD Blue
4GB Geil DDR3 1333mhz
550w Hec Cougar 80

A:No internet in normal mode but works in safe mode with networking

The first thing i would do is stay in safe mode and run a virus scan.

-edit-
Also check for a system restore point.

Use your Install DVD. When on the install now screen choose repair in the left side of screen. Select your OS. Then When at the GUI select system restore. Choose a date before all this happened.

Read other 9 answers
RELEVANCY SCORE 118.8

Hi ,

I'm using windows7 32-bit operating system. I have internet explorer 8( it never worked since installation, always shows "No network connection") and Google chrome installed in my computer. I had been using Google chrome which crashed yesterday. I re-installed Chrome and now it says there is no internet connection. In short, I cannot use internet in my computer. Any other browser installed comes up showing the same "No Network connectivity" thing. And then I started the computer in "safe mode with networking" and I could use see that both Google chrome and Internet explorer are working. But they do not work in normal mode. I really don't know what to do to solve this problem. And internet is working as I'm using internet in my mobile using WIFI from the same internet connection.

Thanks you,
Kavitha

A:Browsers working in safe mode with networking but not in normal mode

Hi and welcome to SevenForums,
Work you way down this list,
Troubleshooting for win-7,
http://www.sevenforums.com/tutorials/220165-troubleshooting-steps-windows-7-a.html
Post which Security suite you have installed as well,
Cheers.

Read other 9 answers
RELEVANCY SCORE 118.8

Hi guys, I'm new to the forum and really hoping you can help me :)

My internet has not been working on my laptop, which happened very suddenly 2-3 days ago. The connection is fine on my other computer and phone, so I know its not the internet itself. Even on the laptop, it SAYS the wifi is connected, but its not working. Firefox was instantly crashing, it wouldn't even bring up the browser window. Chrome gives me a "DNS address not found" error for every site I try and IE wont load anything.

I've tried flushing my DNS, using that ipconfig /refresh and /renew thing. I've tried troubleshooting the wifi connection, disabling/enabling it. I ran a Malware Bytes scan and only found a couple of "pup" programs/cookies that have been deleted. Currently running a SuperAntiSpyware scan.

The thing is, I tried using the internet in Safe Mode with Networking and it works just fine! So that means a program or something on my computer is causing it, right? There were issues with my Teredo Tunneling Psuedo-Interface driver the other day, it had a yellow triangle with an exclamation mark, but I did a couple of fixes that I found on help sites and that exclamation is gone now.

Please help, I really want to use my laptop on the internet again ;_;

Oh, and the specs for my comp are:
Lenovo Win7 PC
Intel(R) Core(TM) i5-2410M CPU @ 2.30 GHz
RAM: 6 GB
Windows 7 - 64 bit operating system

A:Internet works in safe mode w/ networking but not normal mode

In Network and Sharing Center, there is a wizard to troubleshoot connection problems. If that doesn't work, you could "set up a new connection".

Read other 3 answers