Over 1 million tech questions and answers.

Unable to configure Sprout for 3D Capture

Q: Unable to configure Sprout for 3D Capture

I updated my Sprout Workspace to get the new 3D Capture application. After installing I can now longer launch the app and I get the error message "Unable to configure Sprout for 3D Capture". I did a complete reinstall of Windows 8.1 and went back to the original Sprout Workspace and 3D Capture and everything works fine. Has anyone had this issue before and solved the problem?

RELEVANCY SCORE 200
Preferred Solution: Unable to configure Sprout for 3D Capture

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: Unable to configure Sprout for 3D Capture

I reverted to Sprout Workspace 1.04.4.3241 Rev B. Problem solved. I went to: http://support.hp.com/us-en/drivers/selfservice/Sprout-by-HP/7471144/model/7471145#Z7_3054ICK0KGTE30... then paged down to software solutions and downloaded and installed previous version 1.0.4.3241 Rev.B (see the following )

Read other 1 answers
RELEVANCY SCORE 92.4

I recieve folowing error when attempting to perform image capture on mat after update. Request to capture Moment failed with new HPPC_RESULT value as [1.0.d.a0088888] (HPPC_ERROR_EMPTY)

Read other answers
RELEVANCY SCORE 69.2

HelloThanks for the good service you provideI have a problemI was upgrade sprout to win10, and Update workeSpace to Version 1.5.3.2919 ... but Camra own scanner never works and shows errorsso I can not make DocScan , or Capture , 3D Capture .... that very sad

A:sprout can not capture

Please I need help to solve the problem

Read other 7 answers
RELEVANCY SCORE 67.6

sprout captures pictures are .png how can I set the capture to JPG permanently?

A:sprout captures pictures are .png how can I set the capture ...

Hi there @ElReg?,Welcome to the HP Support Forums! It is a great place to find the help you need, from other users, HP experts and other support personnel. I understand that you are a looking for a way to change the default image type for saved images. I am happy to help with this. It appears that changing the default is not an option at this time. But from the FAQ below, and as you have apparently already found, when you save if you choose Save As, you can choose a different file format. Sprout by HP - FAQs for Sprout by HP Please let me know how that works for you, and if it does resolve your issue, please mark this post as a solution. Kudos would also be appreciated.

Read other 2 answers
RELEVANCY SCORE 66.8

Since the most recent update of the Sprout Workspace I have been unable to capture any images or use the document capture. I was able to roll back the updates two days ago and the system worked fine. When I started the computer the next day the update went in again automatically and now rolling back to the old Workspace is no longer an option when I look at the recovery points.  When I try to capture an image I get the following error message: "Request to capture Moment failed with new HPPC_RESULT value as [1.0.d.a0088888] (HPPC_ERROR_EMPTY) If I hit OK and close Sprout and then wait a little the light above flashes the way it should to take an image about 30 seconds to a minute after I tried to actually get an image leading me to believe there is some kind of excessive delay in image capture which is the reason there is no moment captured when the system is looking for it. I believe you have a big problem with your most recent update that is causing. I use this Sprout computer with my students and I need the capability to scan with this ASAP. Right not it is just another computer rather than the all in one device it was bought to be, and that is disappointing.

A:sprout Image/Doc Capture not working after last workspace up...

Hi @jbitting, I have brought your issue to the attention of an appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post serial numbers and case details.If you are unfamiliar with how the Forum's private message capability works, this post has instructions.

Read other 3 answers
RELEVANCY SCORE 66

What is  a Difference betweeh   M2R07AA#ABL HP Turn table 3d capture stage  for Sprout   and     T7U17AA#ABA  HP Turn table 3d capture stage  for Sprout ? Thank you

Read other answers
RELEVANCY SCORE 56.8

This was a problem and I stumbled on a partially remembered solution and then fumbled around and solved it.Every now and then, after some new windows 10 update,   or I accidentally toggle some display change using windows instead of Sprout settings,   or look at the silly thing crosseyed, or... fill in the blank...  the Sprout workspace and even  the  mat as well, stops working.  If I try to start it various ways and finally get the "Sprout Service was not found. Please Start the Sprout Service..." message there is an easy fix..at least until the next time it decides to sulk over something. Lather, rinse, repeat.  1.  Press the windows symbol and the letter X (a long list should pop up)2. Choose "Computer management"3 Choose " Services and Applications"4. Choose "Services"5. Choose "Sprout Services"  (this should land you on the "general" tab for Sprout Services)6. Look for Service Status, odds are it will be stopped or off7. Choose "Start"   That should get all the Sprout workspace and mat stuff back on line. This is a lot easier than tearing apart your system, reinstalling Windows, looking for drivers ect.  You can always do that, if this doesn't work.  But it always has worked for me.    Until there's a new windows update,  I accidentally touch a windows 10 display setting,  look at the silly thing crosseyed.....as I said...lather rinse repeat. This is without a doubt t... Read more

Read other answers
RELEVANCY SCORE 55.6

I understand I can search through drivers and software. But why is there a service offered to find the appropriate drivers. But it doesn't work

A:Sprout Website identifies my Sprout, but no diagnosis.

Hello, and Welcome to the HP Support Community! KateHeaton wrote:I understand I can search through drivers and software. But why is there a service offered to find the appropriate drivers. But it doesn't workI don't know. It works fine with my Sprout!  Instead of using the "Drivers and Software" link, have you tried navigating to the main page for your Sprout?  Go here and enter your exact model number. The world is not perfect.  There may have been glitches with HP/Your ISP/Your Router/Who Knows!? The next time you try it, things might be different! WyreNut

Read other 1 answers
RELEVANCY SCORE 49.6

When Win updates are downloaded, the computer will not configure them and reverts back.What can I do?
 
JN

A:Unable to Configure Win Updates

The cache update files could be damage delete the Windows update cache files.
Save all your open files and close all programs.
Open Command Prompt as a administrator.
Type Sc stop wuauserv press Enter key.
Type Rd  /q   /s  "C:\Windows\SoftwareDistribution" press Enter key.
Type Shutdown  /r  /t 1 press Enter key.
 
After computer restarts check and install available Windows updates.

Read other 1 answers
RELEVANCY SCORE 49.6

When I download Win updates, I am unable to configure the updates. How can this be corrected?
 
JN

Read other answers
RELEVANCY SCORE 48.8

Greeting to all. I have been anable to configure neither outlook nor thunderbird to download or send messages from my yahoomail address. each time a dialogue box comes up asking me for my password. or a message says failure to connect (or something like that) But with gmail things work well. Someone proposed that I use Ypops. I downloaded and installed it but the problem remained.
Thanks for any help
 

A:unable to configure outlook 2010

What kind of configurations you have there?
If you can update on that, would be helpful to rectify the problem.
 

Read other 3 answers
RELEVANCY SCORE 48.8

I have an Asus wireless WL-520GU that I have a wired connection to my PC. Why, because I am using the wireless only to allow access to my webradio.

Problem is the web radio connects 50% of time. Other times to connect I need to manually configure on webradio to connect to connect to wireless. It works sometimes other times not. I haven't been be to get to point of securing the SSID. So probalby someone is stealing my bandwith.

Now to explain my setup, my modem is connected to my Linksys 2102 adapter (used for VOIP) which to connected to the Lan port on the router.

I can surf the web on the PC, but trying to establish a connection, the PC does not recognize a wireless device. I cannot even access the Asus web interface (192.168.1.1)

My default gateway is 192.168.0.1 that of the Linksys adapter,

How to enable SSID so I can lock it and I can access the wireless problem-free from the web radio (Aluratek) ?
 

A:Unable to configure wireless router

Read other 16 answers
RELEVANCY SCORE 48.8

as you can see the properties button does not lit up and remains grey out although i click on IPV4, why is this happening? i was open it a few years ago

A:Unable to configure network properties

Have you done this? Change TCP/IP settings

Read other 9 answers
RELEVANCY SCORE 48.8

I am unable to configure Windows Firewall and Security Center settings on a Windows XP SP2 operating systems. Windows Firewall is disabled. I cannot use the Windows Firewall tool in Control Panel to turn on Windows Firewall or to configure Windows Firewall settings on the Windows XP SP2 computer. When I try to configure Windows Firewall settings, some options are appear dimmed, and I receive the following message: "For your security, some settings are controlled by Group Policy."

In addition, my Internet Explorer default settings are not available.
Recently I removed trojan.cachecachekit and had made the assumption this problem was caused by the trojan. System Restore is not an option because in following the Symantec instructions to remove the trojan I reset the restore date. Can you please help me get my system back to its original configuration?

Thanks! Nica

A:Unable to Configure Windows Firewall

You may not have removed the trojan.cachecachekit completely. IMO I would follow the instructions here http://www.techsupportforum.com/showthread.php?t=15968. Also read this http://www.techsupportforum.com/showthread.php?t=59099.

Read other 6 answers
RELEVANCY SCORE 48.8

Gooday all. I have a laptop set up for my entertainment area. I am using an HDMI cord from laptop to a screen and using the sound output to a set of surround sound speakers. This a pretty cheap set up,nothing fancy. I am trying to get all the speakers recognized by my Realtek Sound Management application. The Lasptop (http://speccy.piriform.com/results/J...8QITBgvOYgX6Ol) is only recognizing a 2 speaker stereo set up. How am I able to change this so as to be able to adjust settings to the 6 speakers of the system. Thanks in advance.

A:Unable to configure speakers on Laptop.

Looking at the Speccy, I don't see anything other than RealTek HD Audio. If the laptop has a RealTek HD Audio Manager, have you tried setting the speaker type there?

Aside from the audio issue, I notice you only have 2GB of RAM. The 64 bit OS does you no good with only 2GB of RAM, and can be an issue with only the 2GB which is bare minimum for a 64 bit OS. The main reason for using a 64 bit OS is to use more than 4GB of RAM, since a 32 bit OS cannot address 4 GB (or more) of RAM.

Read other 2 answers
RELEVANCY SCORE 48.8

Hi All,
I am trying to configure ATA Lightweight gateway on additional domain controller. I am getting the error.
The Console, https://ata.domain.com,  returned an error while attempting to register  the gateway. For more details, please review the Center error logs.

I can open https://ata.domain.com from the DC without any issue and the Port required for the communication is open.
There is no error in Application or system logs on DC or ATA server.
Center error logs in ATA is also not pointing to any error.

Thank you for assistance.

Read other answers
RELEVANCY SCORE 48.8

When I press F1 in Outlook 2010, it starts a Configure dialogue. It always fails, then says restart to complete, even though it says it rolled-back changes. I don't know why it is failing, nor where to look. Obviously, I can't get help within Outlook.

Thanks.

TSG SysInfo:

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Professional, Service Pack 1, 64 bit
Processor: Intel(R) Core(TM) i7 CPU Q 740 @ 1.73GHz, Intel64 Family 6 Model 30 Stepping 5
Processor Count: 8
RAM: 8122 Mb
Graphics Card: NVIDIA GeForce 310M, 512 Mb
Hard Drives: C: Total - 597562 MB, Free - 350316 MB; F: Total - 1907695 MB, Free - 1084235 MB;
Motherboard: TOSHIBA, NWQAA
Antivirus: Kaspersky Anti-Virus, Disabled
 

A:Outlook 2010, Unable to Configure

Have you tried a repair install of outlook or uninstall then reinstall?
 

Read other 2 answers
RELEVANCY SCORE 48.4

Hi everyone,
I'm unable to configure WinRM on a domain computer. I have a simple domain with

1) Windows server 2012
2) A client running Windows 7

If I try to run WinRM on the local Administrator, everything works fine, but if I switch to a domain user, than problems occured.

For example, if i run winrm quickconfig in powershell as the domain Administrator, then I get:

WinRM already is set up to receive requests on this machine.
WSManFault
    Message = WinRM cannot process the request. The following error occured while using Negotiate authentication: An unknown security error occurred.
 Possible causes are:
  -The user name or password specified are invalid.
  -Kerberos is used when no authentication method and no user name are specified.
  -Kerberos accepts domain user names, but not local user names.
  -The Service Principal Name (SPN) for the remote computer name and port does not exist.
  -The client and remote computers are in different domains and there is no trust between the two domains.
 After checking for the above issues, try the following:
  -Check the Event Viewer for events related to authentication.
  -Change the authentication method; add the destination computer to the WinRM TrustedHosts configuration setting or use
 HTTPS transport.
 Note that computers in the TrustedHosts list might not be authenticated.
   -For more information about WinRM configura... Read more

Read other answers
RELEVANCY SCORE 48.4

Hello all.

My Dell Inspiron 3520 was going quite slow for unknown reasons so I decided to 'refresh' it using Windows advanced start-up setting. Since that time I have been unable to install Windows updates. Well, I can 'install' them, but they won't 'configure'. Once installed and 'configured' 100% I get this error message advising following reboot : "Failure to configure updates. Reverting changes". The laptop then stays paralysed on that screen.

This only started to happen AFTER I "refreshed" my laptop, which was running Windows 8.1 pretty-much problem-free, though a bit slowly, until a week ago. For now I have found a temporary 'fix' by disabling automatic updates; otherwise the laptop is constantly stuck on the "failure to configure updates" error page (because, obviously, it's automatically attempting to install updates). I have done all the standard troubleshooting, including running MS Fix It, Dell Dr ('My Dell' found no hardware issues), MS Malware removal and Mcafee anti-malware. All reported "no issues". I have been in command prompt and found no issues I even tried to 'refresh' the laptop again two more times. I have also spoken to two Windows "technicians" and allowed one of them to remotely access my laptop. He found no issues or "violations".

Obviously, the temporary 'fix' of turning off auto-updates isn't a long term solution, and 'refreshing' the laptop hasn't helped (it actual... Read more

A:Unable to 'configure' Windows updates since 'refreshing' l

Have you tried system restore to a good working spot
before format you can use reset factory settings
you can try this in safemode
http://download.microsoft.com/downlo...nostic.diagcab
give a boot from your DVD and give automatic repair a try

Read other 10 answers
RELEVANCY SCORE 48.4

Hi

When I am in Internet Options, Advanced Tab, when I click on an item, it will highlight, but can't click to enable or disable. I am using Mozilla as my primary browser, but don't know if this has any relevance! One
of the main reasons is that I keep on getting an error message from Java (please see log below):-

Additionally, I also receive errors such as FDGO.exe, NTDLL.dll etc etc. I have no idea what I am doing wrong, so would much appreciate all and any help possible!
JavaJava Plug-in 1.5.0_06
Using JRE version 1.5.0_06 Java HotSpot™ Client VM

----------------------------------------------------
c: clear console window
f: finalize objects on finalization queue
g: garbage collect
h: display this help message
l: dump classloader list
m: print memory usage
o: trigger logging
p: reload proxy configuration
q: hide console
r: reload policy configuration
s: dump system and deployment properties
t: dump thread list
v: dump thread stack
x: clear classloader cache
0-5: set trace level to <n>
----------------------------------------------------

Many thanks
Nat

A:Unable To (click) Configure Internet Connections

Uninstall your Java and any Java plug-ins, then reboot your computer. After that, go and try the same things again in your browser options. If everything works out fine, just reinstall your Java and any plugins you may want.

Read other 1 answers
RELEVANCY SCORE 48.4

I constantlly get error_not_found 0x80070490 when trying to install updates.

The Microsoft website says its a CBS issue and that the resoloution is to run a repair installation of Vista. Thing is the software was pre-installed so i have no disc and i'm unsure how to run a restore without an OS disc and also without wiping everything accidentally.

HP say speak to Microsoft, Microsoft say speak to HP.

Any ideas how i fix this one before the PC flies out the window ?????

A:Unable to Configure / Install Vista Updates

Hi -

See if this tutorial helps --> http://www.vistax64.com/tutorials/88...all-vista.html

If no Vista recovery DVD, use the recovery partition - most systems = hit the F10 key during boot-up.

Regards. . .

jcgriff2

.

Read other 1 answers
RELEVANCY SCORE 48.4

When I go to gameplay config controls, it only has the keyboard but when I toggle to any other devices it doesnt even have an option for my gamepad. But windows reconizes the gamepad just fine and it works fine. Just cant config it. Is it something with the game itself or the gamepad. Cause I dont know if I should return the pad or what. I have a MadCatz PC Con USB Controller
 

A:Unable to configure gamepad in Need for Speed Underground 2 - plz help!!!!

Read other 7 answers
RELEVANCY SCORE 48.4

Windows XP Home Ed. My Dell laptop computer loses this setting and I have to reset it each time I start the computer. It looks like this may be because the "Apply" button is dimmed in the Wirelss Zero Config. Properties Window so that I can only click "OK". Have any suggestions?
 

Read other answers
RELEVANCY SCORE 48.4

One of the main reason I never wanted to try Vbox was that I can't figure out how to connect my USB to the guest OS and that always annoyed me. I have a laptop that runs Win10 pro 64bit but I need to install some old applications on my machine that only supports WinXP.

I tried doing it but again I'am facing the problem of not able to attach the USB.

Can someone please help to figure out how to do this correctly. Following are the details that might be useful

Host: Win 10 pro 64bit
Laptop: Dell 3568 with i3 6th Gen 6006U
Ram: 4GB
HDD: 1TB

VBOX: Version 5.2.2r 119230
Guest: WinXP 32bit
Ram: 1GB virtual
HDD: 24GB virtual.

Thanks in advanced..
 

Read other answers
RELEVANCY SCORE 48.4

Hi, I have a Creative Live! Cam Voice Camera. I'm attempting to record a video with it but I simply get an error message that states:

Unable to capture video. Please check that you have sufficient space on your hard disk and the following are set correctly:

-Video compressor
-Audio compressor
Click to expand...

I have more than a gigabyte of memory left on the hard drive, so I doubt that that's the problem. However, I don't know what video and audio compressors are, or how to set them correctly.

Can anyone help?

Thanks.
 

A:Unable to Capture Video

Read other 6 answers
RELEVANCY SCORE 48

I have an application running 24/7 which occasionally loses the ability to pause or configure it by right-clicking on the systray icon.
Is there an alternative method of doing this, or is a reboot the only answer?
(The programme is [email protected]).

Cheers

A:Unable To Configure A Running Appn From Systray Icon

I am not sure what your question is.Do you interact with this or is it a remotely controlled client allowing the use of your computer's unused processing power by the research group?If the program stalled, you may be able to look in the task manager (ctrl/alt/del), highlight the running ap by right clicking on it, choose "go to process" , then right click on the process which will be highlighted and choose "set priority". Try elevating the priority.I suggest you write down what you did so you can reverse it if necessary.There is also a Bulletin Board for this. They might have or be able to provide specific information on the ap:http://forum.folding-community.org/There's also a wiki that may help answering questions:http://fahwiki.net/index.php/How_tos

Read other 4 answers
RELEVANCY SCORE 48

Hi, I recently purchased a pair of Corsair Vengeance 2000 wireless USB headphones. However, when I installed them and tried to use them, I came across a rather unusual problem. I couldn't test them, or set them as default device, or configure them. It's like Windows doesn't recognise them. All the drivers are installed correctly .

I have also tried them on another computer, with the same version of Windows and they worked fine, so I know that there is no problem with the headphones.

I am running RealTek HD audio just incase it is needed.
Thanks

A:Unusual problem: No sound bar for headset and unable to configure them

Sounds like they could have a corrupt status in Windows. Connect the headphones then go to the Device Manager, either the headphones will be listed in the sounds and audio devices or there will be an unknown device listed in the USB section. In either case, RIGHT click on the entry and then LEFT click"Uninstall". Then disconnect the headset and restart the PC. After Windows starts, connect them and Windows should detect and install them, like a new installation. This may take care of the problem.

Read other 9 answers
RELEVANCY SCORE 48

Hi all my friend,
I have a (Air Access) - ZG-5000-11g Wireless Outdoor Bridge , Ap Router, It has hanging problem, so I make it factory default. but now I have unable to configure it. so plz some one help me to find out default ip address.. plz help me&#8230;
 

A:Solved: unable to configure router after factory reset

Read other 7 answers
RELEVANCY SCORE 48

Hello everyone,

I'm about at my wit's end trying to figure out my problem and finally decided I should ask the pros for help, since an exhaustive search of the interwebs has turned up nothing. I'm a hobby PC user so please be patient with me. So here is my problem.

I recently bought all the stuff to build an HTPC/gaming rig for my girlfriend and I and I wanted to set up RAID 1 but no matter what I try, I can't get it to work. Here is my rig.

ASRock H77 Pro4-M mobo
Intel i7-2600
(2) 2TB Seagate Barracuda 7200 rpm; 6.0GB/s HDD
(4) 2GB G.SKILL Ripjaws DDR 1600 RAM
EVGA GeForce GTX 550 Ti Video Card
Cooler Master 600W Silent Power supply

I think that's about it.

Here is what I've done.

I went into bios and set my storage configuration to RAID. After, I saved and exited, and allowed the machine to reboot. When it did, I pushed Ctrl + I to enter the RAID volume setup menu. I labeled the volume, chose RAID 1, selected my drives, selected my size, and saved and exited. Then I booted from my Windows 7 Home Premium 64 bit (Dell OEM, if that matters). I selected my regional settings, and when prompted, accepted the terms and selected "Custom" install. At the drive select screen, I saw one disk, which I believe is what I should see. I highlighted the drive and selected "Load Drivers." I used the driver labeled with the arrow in the attatched image. I got it from my mobo's website found here ASRock > Products > H77 Pro4-M. After the driver loaded, I re... Read more

A:Unable to configure RAID on Windows 7 Home Premium

Why do you want RAID? WIn7 doesn't much like RAID which isn't even Redundant so risks losing both HD's if one fails. Better to install to one HD and use the other for backing up an image.

If you saw one correctly-sized RAID array when you booted into the installer to try hardware RAID then the driver wasn't needed as it's only loaded when no drive shows up. Try again.

Read other 9 answers
RELEVANCY SCORE 48

After restoring my new laptop back to factory settings (to fix problem I was having with MSE), I find that I am now unable to configure my restore points. I am trying to increase the storage space so I can have several restore points. When I click 'Apply' or 'Okay' after changing the space allocation, the following error appears:

"The filename, directory name or volume label syntax is incorrect. Error 0x800707B"

The following drives appear in the Restore Config window with Restore set to 'On':

System_DRV
Windows7_OS(C:)(System)
Windows7_OS(C:)(Missing) -- this seems odd to me

For background info, I restored to factory settings and added MSE and then other programs one-by-one. After programs were re-installed, I restored my data from the previous night's backup. Everything is working fine and there are no system errors that I can see.

Would anyone have any insights on this problem?

A:Unable to configure restore points - Error 0x800707B

  
Quote: Originally Posted by hallydai


After restoring my new laptop back to factory settings (to fix problem I was having with MSE), I find that I am now unable to configure my restore points. I am trying to increase the storage space so I can have several restore points. When I click 'Apply' or 'Okay' after changing the space allocation, the following error appears:

"The filename, directory name or volume label syntax is incorrect. Error 0x800707B"

The following drives appear in the Restore Config window with Restore set to 'On':

System_DRV
Windows7_OS(C(System)
Windows7_OS(C(Missing) -- this seems odd to me

For background info, I restored to factory settings and added MSE and then other programs one-by-one. After programs were re-installed, I restored my data from the previous night's backup. Everything is working fine and there are no system errors that I can see.

Would anyone have any insights on this problem?


Turn off SR, you can read help to find out how.
Turn off computer
Boot up
Turn on SR
May not work, but it does 3 out of the 5 times the problem was on this board.

Read other 5 answers
RELEVANCY SCORE 47.6

I'm unble to capture video via Firewire from my Sony Mini DV camera. I've had this problem with both my camera and a borrowed Sony semi-pro model Mini DV cam.

I have the Firewire 400 to mini Firewire cable but my video capture program doesn't recognize the connection.

The Firewire card works, I'm able to connect an external hard drive with no problems.

And yes, I have applied the Windows XP firewire patch.

Does anyone know how to fix this? I need to do some video editing and I don't want to have to shell out the $$$$ for a Mac.
 

Read other answers
RELEVANCY SCORE 47.2

New server built to replace old 2008 R2 server. All installed OK, FTP/SMB and repositiry all setup OK and tested connections with no errors.  Repository location permission checked and all OK FTP access checked and all OK So I can submit tasks which work OK like *Update Agent and *Factory Reset Agent updates to 4.7.3670.25932 - This is on HP T520 I have imported a old task for image deployment and if I run this task it connects to FTP downloads image OK then reboots and on device all looks OK but the task has failed with below errors (at bootom of post). Also the agent gets reverted back to 4.63.670.21244 (which is version on old captured image). So I also tried to capture a new image (after updating Agent) but when this happens the device comes up with a HP screen about not turning off etc then appears to reboot but then just sits there with blank screen and no activity for hours. The task on HPDM also just sits there. If a power down the thin client and start back up the tasks then goes into failed status. Monitoring FTP I can see connections and files/folders being copied/deleted. Error logs: Task Name: XPOUK_STDv1Task ID: 00000029OS Tab: HP ThinPro 5Sender: rootSequence: NoValid Time: 1440 minute(s)Write Filter Policy: Execute & CommitExecution Timeout: 30 minute(s)Cached Updates: NoWOL before task: NoTask Deferment: NoExclude Working Hours: NoBatch amount: 5Interval between batches: 2HTTPS Repository Speed Limits... Read more

Read other answers
RELEVANCY SCORE 47.2

After Windows 10 1803 update, the loopback capture scenario does not show network events.
Repro steps :

I run Message Analyzer as an adminNew SessionLive TraceSelect ScenarioLocal Loopback network
Navigate with my browser to any self hosted web site at 127.0.0.1, any port.
try ping 127.0.0.1 or localhost
The analysis grid only shows Windows_Kernel_Trace modules.
I tried uninstall, install Message Analyzer again, update Assets (they are all in sync).
Any help is appreciated

Read other answers
RELEVANCY SCORE 46.8

My daughters' Satellite laptop just came back from Comp USA where it had been for some major restorative surgery. None of her previous software made the return trip home....

I had bought her a Netgear wireless card, which we thought that she had lost some time ago...hence the disk was picthed. I found the wireless card...go figure...in a pocket in the heavy duty case I got her on eBay. I inserted the card and Windows kindly offered to reinstall the software, but alas..no disk. I've physically plugged the machine into our LAN and visited Netgear's site where I downloaded (at a paionfully slow pace..unusual as we are on broadband) what I assume is the correct driver. The files I downloaded are zipped, but none of them actually appear to be self-installing.

I have extracted the files but there does not seem to be any way to make any of them do what I need. I can list the filenames/extensions if that would be useful. Sincere thanks to anyone who can find the time to help.
 

A:Toshiba laptop/Netgear MA401 unable to install driver/ configure

if you goto device manger is th ewireless device there - if so have you tried re-installing driver from there.
or add new hadware and when ask for driver point to your files.

listing here may help

also model of wireless card will help to

heres a free wireless program which detects wireless signal in the area. i found this useful for diagnosing if a problem with hardware or signal

Free software to check signal strength of wireless is netstumbler 0.4.0 available for download from http://www.stumbler.net/
 

Read other 3 answers
RELEVANCY SCORE 46.8

hi i am trying to capture a windows 7 image for my MDT server.  The MDT Server is running Server 2012 R2 Standard and it has MDT installed on it.  it is running MDT 2013 Update 1.  every time i go to sysprep and capture the image sysprep
is OK but when it reboot to package it and upload it to the server i first get a unable to connect to the server then when i hit retry it says connection ok.  possible cause invalid credentials.  why is this happening? i don't have customsettings
or bootstraip.ini using any account i enter them my self because of reasons. could it be a bug in MDT?  Please someone help me.  I am using VMWare workstation 11 for my reference image.

Dudefoxlive

Read other answers
RELEVANCY SCORE 46.8

Hi everybody, I'm facing a problem with a fresh installation of HPDM v4.6 (which already gaves me some trouble during installation but is now running "quite" fine). When i try to capture a thin client image (T5545 / T5565 //// T5X33009 or T5X31012), it works fine until the thin client reboots, just after having sent the image, "dd.gz" based, to the FTP repository. The error is reported like this in the LOG (HPDM french language was installed, GRRRRRR) :2014-04-15 10:05:44Envoi de la tâche à la passerelle de gestion des périphériques réussi2014-04-15 10:05:46La tâche a été récupérée par l'agent.2014-04-15 10:12:51La tâche a été récupérée par l'agent.2014-04-15 10:13:28[Code derreur : {0}] [Module : {1}] [Catégorie : {2}]2014-04-15 10:07:23[Détails de l'erreur]: ../../Task/linux/[email protected]:Failed to handle post image.../../Task/linux/[email protected]:Imaging operating failed.../../Task/common/[email protected]:Upload file error.../../Task/common/[email protected]:;socket select timeout.2014-04-15 10:13:28Impossible d'exécuter la tâche common. Hope someone can help me because i don't know what the problem is related to.  Thanks !

A:HPDM 4.6 - Unable to capture image (error 34603008)

More information : i tried to add a template to deploy an image to a thin client and i got an error which was : 2014-04-15 11:19:48Mappage du référentiel vers : Référentiel principal2014-04-15 11:19:48Mappage du référentiel vers : Référentiel principal2014-04-15 11:19:48Envoi de la tâche à la passerelle de gestion des périphériques réussi2014-04-15 11:19:50La tâche a été récupérée par l'agent.2014-04-15 11:23:12La tâche a été récupérée par l'agent.2014-04-15 11:23:19[Code derreur : {0}] [Module : {1}] [Catégorie : {2}]2014-04-15 11:23:19[Détails de l'erreur]: ../../Task/linux/[email protected]:Imaging Operating Failed.../../Task/common/[email protected] file error.../../Task/common/[email protected]:;socket select timeout.2014-04-15 11:23:19Impossible d'exécuter la tâche common.

Read other 9 answers
RELEVANCY SCORE 46.8

Please Help!!!

I am using Corel VideoStudio 12 and have a Canon Hv10 camcorder. I have used both the camera and the software successfully in the past. I am currently trying to capture some footage from my Canon HV10 to Corel, but the software keeps popping up the following message "Unable to switch to capture mode. Check if your video capture drive is working properly. [15023:4:2]"

I have been told by someone that it is perhaps because my camera settings for output and my software settings are no longer the same (which would explain why it worked before but not now). I have no idea if this person even knows what they're talking about, and I have no idea what settings would need to be changed (either on the camera or the software) and how to change them if that is even the case.

Please help.
 

Read other answers
RELEVANCY SCORE 46.4

At random times, I get that much hated Blue Screen of Death. I can be running any number of programs and walk away and come back and there the screen is blue. I have tried to keep my PC up to date, I run the latest Avast Internet Security Suite - just looking for some guidance on how to stop these issues, as this is our main work station in our office (we are graphic designers/3d texture artists) so we run some memory intensive programs, but the machine is not old, so I am kind of perplexed as to why this is happening.
Thank you in advance for any help

A:BSOD Randomly (unable to capture error before restarting system)

Hello and welcome to SevenForums!

Please follow this guide, get a BSOD and report back.
Dump Files - Configure Windows to Create on BSOD

Read other 1 answers
RELEVANCY SCORE 45.2

Hello.  We are switching our shop from Intel NUC's to the M90n-1 Nano's.  We received one for testing and we really like the performance from the older NUC's.  On the test machine I was able to install all of the aftermarket software we use, remove all the horrible bloatware that Microsoft seems to think Windows 10 Pro needs, and sysprepped the machine.  All of this up to this point was great and had no problems.  Now I am ready to pull the image from the machine and place it into our WDS images (running 2012 R2).  We have secure boot off, PXE enabled in bios.  Have installed 36 various drivers onto the WDS.  We connect the LAN, power on, press F12, select PXE Boot from IPv4.  It checks for media presence, finds the media, then displays "Start PXE over IPv4 on MAC: XX-XX-XX-XX-XX-XX".  It will sit for several seconds to just over a minute and then the screen will flash and then it will start the process over using IPv6.  After it tries IPv6 it will shut down.  I took a video and noticed in the video that when it flashed it displayed "NBP file downloaded successfully" but still just goes to IPv6 before eventually just shutting down.  I tried spamming the heck out of the enter key after the "Start PXE over IPv4" message and also spamming F12, neither altered the outcome.  Has anyone else ran into this, and if so did you find a solution?  We have an order for 50 more of these that are on hold as... Read more

A:ThinkCentre M90n-1 Nano: PXE issue, unable to capture image and place on WDS server

So it appears this is the solution/work around.First disable the OS Optimized Defaults setting.After disabling the OS defaults, press F9 then F10 to load the default BIOS settings.Change the Boot Mode setting to Legacy Only.You might need to disable the Secure Boot option to change the boot mode.There is a PXE Option ROM option that should be disabled and the Onboard NIC option set to enabled.

Read other 1 answers
RELEVANCY SCORE 43.2

Does anybody know if there are any capture cards that are actually recognized by the Vista OS?

I recently got my laptop from dell and vista works fine its just the fact i would like to get a USB port Capture Card.

Anybody have any advice for me?

Thanks

Read other answers
RELEVANCY SCORE 42.4

I am running Hyper-V on Windows 10 Pro and trying to install CentOS 6 on a VM. I define an external virtual switch, create a VM, specifying the use of the external virtual switch. I have 2 NICs on the host system, both with network access and internet access. The external virtual switch creation specifies the use if the Intel NIC and creates a vEthernet definition in the control panel. When I install the VM, it has an ifcfg-eth0 that specifies dhcp and onboot=no. When I run ifconfig -a I see a definition for vibr0 that has in IPv4 address of 192.168.122.1. My network is 192.168.200.nnn and even though service network restart says it is OK, I cannot see anything on my network. There is no ifcfg-vibr0 defined so I can't change the IP address to one that works.

Read other answers
RELEVANCY SCORE 42

Hi,
I recently purchase a DIY desktop computer but it does not come with a firewire port. I installed one on the pci slot and it was detected by the computer.
Now when I pluged in a 6 to 4 pin firewire cable to my DV cam, I could not do a capture in either the Movie Maker or Premier Elements. It says 'no capture device detected'.
I checked on the hardware under device manager, and it shows that the firewire card is working properly.
I also tried using the USB port on the DV cam to capture, but it was not detected. I heard that it requires a seperate driver from JVC manufacturer. My Cam model is GR-D270.
I would appeciate alot for any answer to my problems.
 

Read other answers
RELEVANCY SCORE 42

I bought this Elgato capture card yesterday and I've been trying to get it to work. I've updated my driver, and changed the video quality on both of my monitors, along with the profile (quality) on the software but I keep getting this message:

I don't know what it means by "video output format" but I want to be able to record off of it, so thank you in advance if you know how to help me.

http://postimg.org/image/xo9n729c7/
the image link, if you can't see it.
 

A:Elgato Capture Card: Won't capture anythng

I'm not familiar with it. But based on the image, there is no input signal (upper right box - Game Capture HD "no signal").

So the error is likely trying to tell you to change the output video type of whatever you have connected.
 

Read other 1 answers
RELEVANCY SCORE 42

Anyone have any tips on why I am not able to upload an image directly to my WDS server through the Image Capture Wizard?  I can capture the image to the local hard drive, but when I try to connect to the WDS server to upload it, it takes about 5 minutes and then tells me that the network path cannot be found. 
 
I am able to use the wizard to create a .wim file which I can then upload manually, but I would much rather upload the image through the wizard and save myself an extra step. 

Read other answers
RELEVANCY SCORE 40

I don't know why, but the capture program on my laptop crashes whenever I hit "stop capture" after recording some gameplay footage. The software is up to date (2.0) and I don't know what else to do other than uninstall and reinstall the software. I was recording some gameplay footage earlier today and the program crashed as I hit stop recording. The video file didn't appear when I opened the program again but an m2ts file of the capture did appear in my videos folder with a bugged mp4 file. Options?

Read other answers
RELEVANCY SCORE 40
Q: Sprout

Does Sprout have the software/hardware ability to recognize a Möbius Strip on the 3D platform? The Möbius Strip possesses the unique property of being mathematically non-orient able.This leads me to the next question, Will Sprout allow for the input of equations and generate 3D solids, virtual, from that data? Will Sprout allow for mathematical definition of the scanned 3D object from the platform?

A:Sprout

My son read the post over my should and then ran off and made a quick Möbius Strip out of paper.We put it on the stage and let did a 4 cycle scan.    https://flic.kr/p/vF6o9XThe 3D scan was not able to complete close the shape.  But it was interesting to watch it try to build the image. The 3D scanner is just that, an Intel RealSense 3D camera shooting a laser at an object and collecting the point cloud and then doing its best to try to figure out where the surfaces are.  There isn't an interface to input an equation.  When I was doing my degree 20 years ago, our professors used to push the point that there was a somewhat large gap between pure mathematics and how those concepts exist in this world.  If you want a model of an abstract mathematical concept best represented by an equation, I think there are better tools. That being said, I have thought of trying to produce an OBJ file from another 3D tool and then trying to use that with the Sprout.  If it's just a matter of dropping the OBJ, MTL and baked texture into the right directories, then I already know where the Sprout stores those files.  Then it might be interesting to mix simulations (scans) with simulacra (generated models of abstract concepts).

Read other 3 answers