Over 1 million tech questions and answers.

9800SE thinks it has 8 pipes.

Q: 9800SE thinks it has 8 pipes.

Recently I was getting artifacts in games and noticed that the card was running hot so I got an Artic Cooler on it which is fine (much cooler now).

However in games I get the checkboard pattern over the game. The framerate is perfectly fine. Setting games to use 16 bit color / z-buffer reduces the problem slightly. I installed ATITool to see if underclocking would help then I noticed in the window "Active Pipelines: 8". Its a 9800SE, it should have four pipelines and every time I have used ATITool before it has reported four.

I have never done the soft or hard mod to this card.

I've tried a complete format and reinstall with various old and new drivers and the problem I still there. As I said the framerate etc. is fine. From what I have read about the softmod, the checkboard effect is often because the card can't handle the mod and do eight pipelines, so (hopefully) if I can set it back to four it will work fine.

Any idea why it would set itself to eight even though I have never modded it?
Is there any way to set it back to four? Maybe a bios flash that restricts it to four?

Thanks for reading.

Read other answers
RELEVANCY SCORE 200
Preferred Solution: 9800SE thinks it has 8 pipes.

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

RELEVANCY SCORE 48.4

How effective are heat pipes, could they be used to cool a P4. If the copper pipes were brought outside the case and placed in a sutible cooling medium e.g an ice bath and the section of the pipe that was in the case was insulated to keep the case temp down, would this make a suitable silent cooling system.
 

A:Heat Pipes

Heat pipes are now used in heat sinks very effectively these days. I was a little sceptical to the efficacy of heat pipes till I realised that most laptops use this tech to keep the CPU cool, and comparison tests have shown that its much more efficient thatn without it.

How it works:
Basically, it just provides a heat conducting rod with low thermal resistance. Therefore, its efficacy is reduced the longer it is. Its like stretching a metal rod over a fire, a short one you'd burn your hand pretty fast, a long one you might not feel anything at all for a long time.

Also, I doubt you'd want to insulate the section of the pipe in the case, you'd more probably insulate the whole thing. At least you'd insulate the bit outside the case, so that the cold temps from your ice bath will reach the PC. But you want it to reach the CPU, so you'd insulate the whole bit. And you'd need a really thick heatpipe....

I won't suggest you do that.

A better solution? Water cooling, and run your radiator through that ice bath of yours
 

Read other 1 answers
RELEVANCY SCORE 47.2

I need help unlocking unlocking pipes and shadders for my 7800GT , like it says in the title.


Thanks for all the help I know I will receive!!

(450/1.08 OC'd @ 500/1.18)
 

A:Unlocking pipes and shadders for my 7800GT

Help!!!!




:bounce: :bounce: :bounce: :bounce: :bounce:
 

Read other 6 answers
RELEVANCY SCORE 47.2

Good evening. i am learning how to work with threads and process in WinAPI. During this, i faced with interesting question. When i created
named channel i used pipes. I used #define BASE_PATH_PIPE "\\\\.\\pipe\\PipeName". So can you please answer me. In wich folder pipes storaging in my computer. I used search on my hard disk and did not find it. Where i can find this storage with pipes.
Thank you

Read other answers
RELEVANCY SCORE 47.2

Hello, I just bought a hyper 212x a little bit ago and i smell something's that smells like its coming from the heat sink. I checked the the copper pipes sticking out of the heat sink and there was one that looked like it shouldn't be like it and was very small.
 

Read other answers
RELEVANCY SCORE 47.2

 Hi, There seems to be 2 types of fan modules installed on the T460s (besides the one that is for the model with dGPU). One of them is with one heatpipe, the other one is with two heatpipes. Two Heat PipesSingle Heat PipeCan someone tell me what is the difference between two and which one is more efficient? Lenovo Staff maybe? Also what is the reason for that some i7 are with 2 Heat Pipes and others are with 1. There is also difference between the fan modules. The single heatpipe fan is with 4 wires, while the other one is with 5 wires.  P.S.> And NO it is not the i7 vs i5 CPU, because I have i7 and I am with single Heat Pipe.   




T460s - Core i7-6600U, 12GB RAM, 512GB SATA 6G SSD, FHD, EM7455 WWANT440s - Core i7-4600U, 12GB RAM, Crucial MX200 500GB SSD, FHD, WWAN








Solved!
Go to Solution.

A:T460s - Different FANs and Heat Pipes

The only one I have seen has 2 pipes.  Was one of them made earlier than the other?  (On the model sticker, there is a manufacture date after the serial YY/MM.)  The parts list only shows one manufacturer.  As far as 4 wires vs. 5 wires, I would expect it wouldn't matter.  Normally, only 3 wires are used - power, ground and tach pulse.  I would expect it wouldn't matter.  I looked at eBay for T460s fans for sale thinking I could see a picture.  They had 2 for sale - one with 1 pipe and 4 wier; the other with 2 pipes and 5 wires.

Read other 3 answers
RELEVANCY SCORE 47.2

I have a HIS x1800gto that i know is unlockable with the right bios, ive acquired a bios that will do it its just that i am having incredible difficulty doing so.

My comp at first didnt have a floppy drive so i went with boot cds. The bootable cds wouldnt work for reasons unknown, i created like 5 of them, none would really get working so i jsut caved in and attatched a floppy drive.

created a bootdisk with atiflash, didnt work, reasons unknown, maybe because its a HIS ICEQ3 x1800gto and not a native (made by ati) card, so i used flashrom240, 237 and 16p. none worked. the same problems would come up-

device 0 not found
ati adapter not found
error 0FL01 when i tried to force flash.

obviously the card is there and is working fine. before this a while back and as recently as a few hours ago i attempted atiwinflash. ive heard horror stories about this program but it never really did or work for me till about 40 minutes ago. what i did was i just flashed it again with a fresh HIS x1800gto bios in an attempt to get flashrom to recognize my card. no dice.

now im at a loss since i know the card is there, its operating normally, its not overclocked, temps are prolly at 40c i would wager, so everything should be a go. anybody else have this card or been thru this?

thanks for any help my dudes.
 

A:Trouble flashing HIS x1800gto into having 16 pipes

Flashing those cards isn't guaranteed to work. If it was, they would be sold with all 16 pipelines already enabled. Maybe MOST of them can unlock, but maybe yours just can't. Obviously, if they could ALL be flashed to 16 pipelines, they would be sold as having 16 pipelines because the company could sell them as a more powerful model and get more money from them. Those ones are cards that were made to run on 16 pipelines, but were unable to according to some test (however inaccurate that test may have been). This means that some WILL run at 16 pipes but some won't. I guess you just got unlucky
 

Read other 4 answers
RELEVANCY SCORE 46.8

ok, so it's an msi m/b

https://www.targetsecure.co.uk/newtc24/default.asp?vendor=&MenuId=766&Prod=MBMSI-P35-NEO-F+

I'm only overclocking the cpu, using an Noctua NH-U12P

Will the m/b heatsinks cope with the cpu at around 3GHz?
 

Read other answers
RELEVANCY SCORE 45.6

after you come from the cliffs and your heading into the pipes, right after the loading screen for the next stage my game keeps freezing my guy so he cant move but i can still move around, its really strange. My friend (who was the one playing at the time) said the same exact thing happened to his game in the exact same spot and it was fine before steam came out but since steam was released there was some update where now at that point it freezes on a bunch of systems...whats the deal? is this fixable?
 

Read other answers
RELEVANCY SCORE 45.2

Hey my m8 has a 9800SE and he wants to upgrade it to a 9800PRO at leats but preferably a 9800XT, i told him bout the fact that it has only 4 pipelines enabled and the other 4 can be enabled and hes up for it, i know the easiest way to do it is to softmod it with omega drivers or summit like that but we tried it and it just made his system run very very slow.

So i had an idea about flashing the BIOS to a 9800 PRO or XT BIOS and wondered if it would enable the other 4 pipelines? i have flashed the BIOS on my fx5900XT with a 5950Ultra BIOS and it works fine so i know how to do it and the risks of it but if i did put a 9800 PRO or XT BIOS on there would it enable the other pipelines and would it work kool? there is extra coolign on the card already so no worries bout overheating or anything..

your help wud be appreciated!

Orgasmo
 

A:9800SE to 9800PRO/XT??

If softmodding doesn't work, it means the extra pipelines were defective. Flashing it with a 9800 Pro/XT Bios will only force those pipelines to be constantly active resulting in visual artefacts & strange performance behaviours. It's best not to try it.
 

Read other 5 answers
RELEVANCY SCORE 45.2

i am about to buy a powercolor 9800SE 256MB and i know that it can be softmodded to a 9800PRO on some chips. i have also heard that if your chip is defective on which 4 of the 8 pipelines have been damaged it can produce a checkerboard effect or put multicoloured dots over your screen.

Does anyone know if this softmod can be reversed if it is unsuccessfull??

Thanks in advance
Nick
 

A:9800SE -> 9800PRO

The modifications are only done in the driver so if it doesnt work you just uninstall the softmod driver and install the ATI Catalyst driver.
 

Read other 1 answers
RELEVANCY SCORE 45.2

I'm tring to run IL2: Forgotton Battles. It works fine in DirectX mode but reboots everytime I click fly in opengl mode.

Anyone experience this? Would it be driver related?

Any Suggestions?
 

A:9800SE and OPENGL

Reinstalling drivers should help, but still theres nothing wrong with running it on directx is there?
 

Read other 3 answers
RELEVANCY SCORE 44.8

I've been at this thing for days on end. And cannot get it to work. I am using both Composite and Tuner modes. Tuner does not detect any channels.

The main problem is that, when I go to play NTSC PS2, GC games etc they show up black and white. I've been switching to NTSC mode constantly, but I get the same thing. And when I try it with Tuner mode, it still doesn't work, even though I have a SCART lead in. The closest I can get to colour is by playing PAL games (duh) or by displaying NTSC/JAP games in PAL_60 mode, however PAL_60 flickers alot and has a huge black bar on the left hand side of the display. Not good.

So I ask of you, would anyone be kind enough to help a n00b like me out? ;_;
 

A:ATI All In Wonder 9800SE not displaying NTSC.

Hi News Bot, welcome to techspot and happy new year

One simple question, have you updated your driver from
http://ati.amd.com?
Also why don't find a program like catalyst to manage your AIW? It'll be easier if you have it.
 

Read other 1 answers
RELEVANCY SCORE 44.8

Hi all,

I was wandering if anyone has successfully got their Radeon 9800 (or any of the older cards that require legacy drivers) working on Win 8.

I tried both the AMD Catalyst Win 8 Preview drivers, but they obviously don't support the legacy cards. I've also tried the Vista drivers, the same ones you use for Win 7 (which work fine), to no avail.

Any ideas?

Jamie
 

A:Radeon 9800SE driver for Win 8

That's a pretty old card. If you want all the eye-candy, you should buy a better card.
 

Read other 2 answers
RELEVANCY SCORE 44.8

i own a radeon 9800se gfx card but i have noticed a few problems.
i get some sort of horizontal lines which flicker around the screen on my desktop, if i increase my colour quality from 16 bit to 32 bit the flickering is increased, however if i keep it set on 16bit they are no lines on my desktop but as i play my games they come back.when i try and play any game they are more lines. to explain myself better i have attatched a print screen
 

A:Radeon All in wonder 9800se problem

Read other 16 answers
RELEVANCY SCORE 44.8

Does anyone know, can i turn my ATI 9800SE 256meg card into a All-In-Wonder card? is it possible or would i have to buy one?
 

A:turn a 9800se into a all-in-wonder card

I'm thinking you'll have to buy one - or at least buy a TV card.
 

Read other 5 answers
RELEVANCY SCORE 44.8

i am building a barebones system and I need a decently cheap graphics card. so far i've found these three-

nVIDIA FX5200 128Mb DDR , 8X AGP

ATI Radeon 9200 SE 128MB DDR AGP 8X

nVIDIA FX5200 256Mb DDR , 8X AGP

the last one, the 256mb, is 25$ more than the 128mb one. I plan on doing a little gaming but mainly graphics work on Photoshop and Illustartor. Which one would you suggest? And which one is the better brand, and last but not least, in what way does the megabite rate of the card matter?
 

A:How is the ATI (Radeon) 9800SE for gaming?

Read other 16 answers
RELEVANCY SCORE 44.8

Hi everyone, I've got a problem here...

I recently got given my friend's old Radeon 9800SE card, which he said was cutting out after a few minutes of use. I thought this was overheating, so I removed the GPU heatsink and replaced the rock-hard thermal stuff with fresh goop.

It now runs without cutting out, but when I try to run anything 3D or play a video clip, there's lots of horizontal lines or regularly spaced green dots on the screen. Any idea why this is happening? Was something damaged by the heat?

Also, if I use the Catalyst 6.11 driver, it acts very slow, but if I let Windows install its driver by itself (Xp installs version 6.14, which is not available on the ATI site) it works fine. If Direct3D and DirectDraw hardware acceleration is turned off, the lines disappear. Does this mean it might be a driver problem?

Thanks!
 

A:9800SE problems - artifacts

What are your system specs???
 

Read other 2 answers
RELEVANCY SCORE 44.8

Don't know how to explain this problem.
I have bought 9800se and cannot use it, because it restarts the pc before or on the user's screen of winxp (the screen freezes or is restarted without asking)

I have tried to install drivers on "Safe Mode" in Winxp, but when ask to reboot it's the same :wtf:

First I start on the drivers Omega(downloaded) and I put 9800se overcloked (and normal too), then I try to install the disc drivers that come with the graphic card (Ati display driver), installs perfectly the Winxp driver, I put "not to reboot" to install the catalyst drivers that come on the same disc and there is when freezes the pc (the red light keeps lit, as if it was working).
Note: before installing again any other driver I have insured myself of erasing the previous one.

Can't install any driver

My pc caracteristics:
P4m80-m7a with bios update
Winxp with sp2
512mb
Pentium4 3.01ghz

Reading a somewhat similar problem, it seems I have to format and reinstall WindowsXp
 

A:Problem with 9800se ┬┐drivers maybe?

The 9800SE should have an auxilliary power connector. Did you forget to connect it to the power supply?
 

Read other 6 answers
RELEVANCY SCORE 44.8

ive always been told to go nvidia over ati because the drivers are horrible. but somehow i decided to get a sapphire 9800se card last june so i could use 2 monitors. this thing ran perfectly on the ati drivers that it came with, till bought a new board (because my last one burnt up)

this new board is almosty the same as my last one, just has less features. but no matter what i do, ati, sapphire, omega, i cannot get this thing 100% stable. if i try installing simcity 4 it will just turn off both monitors and force me to do a hard restart. then sometimes will not go past my core cell picture screen in post. any ideas on who makes a sweet driver for this card?

amd 64 3000+
1 gig of ram
ati 9800se sapphire

my new board has an 8x slot like the last one too

k8t neo v
 

A:radeon 9800se drivers

after holding for 45 minutes, ati told me that i had to install the catylyst and driver from their website to begin with. he pretty much told me to throw away my video card disc (not that i will) because its useless. my problem was that i had the catylyst version 5.0 alongside with the newest driver. i had to completely uninstall my video drivers and load up catylist 7.9 and the driver meant for that, and now it runs mostly fine. there still are the hard restarts it will do by itself, and the error report always says video device driver in infinate loop, but i dunno.

it will hold me over till i buy a laptop this summer
 

Read other 1 answers
RELEVANCY SCORE 44

Hi guys,

I just installed a 9800 SE. My PC monitor has always been a little dark. What I want to do is have my brightness/gamma settings under the color tab and advanced settings to carry over to game.

My old video card would do this. My 9800SE's brightness/gamma gets reset to default once any game is booted up.

Is therer anyway to keep these setting for games with my ATI card? Would the problem be the driver?

Using Cat 3.10, ATI 9800SE, P4 2.4, 512RAM. If that matters.

Any help would be appricated, thanks.
 

A:9800SE Brightness/Gamma Question

When you set the gamma, did you click the little box to switch from desktop to 3D-Gamma?
 

Read other 3 answers
RELEVANCY SCORE 44

The fan won't spin on my GPU. I have the power cable connected properly and my drivers are up to date. The Card works fine but it heats up REALLY FAST and I'm worried about a burnout. HELP!
 

A:Sapphire Radeon 9800SE Fan Won't Spin

Read other 9 answers
RELEVANCY SCORE 44

Spec:

550W Dual Fan PSU
AMD Xp 2500+ 1.4GHZ
1 stick of 512MB
2 Hard Drives
DVD Writer
1 USb Modem Connected
PCI Soundcard
ATI Sahpphire Radeon 9800 SE 128MB

Windows XP SP2

Software relating to VGA:

Direct X 9.0C
Latest Drivers from ATI

Problem:
********

My PC will all of a Sudden Power Off (like someone has removed the power cable from the tower).

I bought the Radeon 9800de new toughly 4 weeks ago and had no problems what so ever installing the car and
getting the PC up and Running, over this period I have played Doom III and A Half Life 2 Demo, with no problems
what so ever. Thursday there I started to run into this problem. I was doing nothing different and the card has
not been over clocked.

The system powered down and I could not power it backup, I then realised my 350W PSU was goosed. I therefore obtained
the 550W PSU, which solved the problem for the duration of the night. I left the PC running overnight and the PC was still
running the next again morning.

That afternoon I tried to play game and the Computer cut out once more. I then pulled the power plug out for 5 seconds, then
re-connected the plug back into the PSU and powered the CP backup. I got as far as my Bootloader, then the PC powered down. This
power down no happened sometimes even before i get as far as the bootloader and sometimes later.

For now I ave installed a very old voodoo 3dfx PCi card and no problems what so ever and the pc has been running for over a ... Read more

A:ATI Radeon 9800se I think is Killing my PC (powering PC Down)

..

I'd say your next step is to plug in a known working AGP card. I'd be surprised if your brand new card suddenly up and died, but it is possible. Your AGP slot could be the culprit in this case. Which would mean you'd need a new motherboard.

As a side note, since the ATI card draws more power than the last video card that you had in there, I assume, and it runs fine with the old PCI card. It is very possible that the socket you have the computer plugged into simply cannot power everything needed. This can happen in older houses/apartments etc. and newer ones as well that have not been properly wired. I bring this up as I had the exact same problem in sept. of last year and I had to fix the wiring in the wall to fix the problem. There wasn't anything wrong with my computer. If you try another known working AGP card that draws as much or more power than the ATI card you've got and it doesn't work I'd look to the wiring inside the wall. No joke.

-A-
 

Read other 3 answers
RELEVANCY SCORE 44

Running Windows XP SP2 on an ASUS motherboard (P4C800) with ATI All-In-Wonder 9800SE. Since a few days, I'm seeing yellow lines and rectangles on my screen. Strange thing: If you resize an open window, these yellow things disappear.
I remember someone telling a similar story, on other hardware, but can't remember the details.
Could this be hardware related?
I've already tried to install another driver, without success. Yellow lines etc. still appear.
Note that they do not show all the time. Very strange!

Thanks for any advice!

Koen

[edit] These yellow lines and rectangles are actually a kind of transparent layer which gives a yellowish look to some zones on the screen. Just to make things clear...
 

A:ATI AIW 9800SE shows yellow spots

Um, this is a really bad problem. I had a 9800 PRO 256MB die on me just a few days ago to a similar problem, it would do that every once in a while, and then go away. But just recently, I bought a new case and PSU, and luck should have it, all the letters during boot are rainbowed, and it doesn't go away, my card is dead, wont even boot anymore. I would first start off with a thorough inspection of the card itself, and the die. Using a picapole works well (what printers called a set magnifier) to see if the top of the die cracked, or corner chipped, like mine started to. look for your thermal cream running, hope it isnt, because that could cause it for the short term as well.

When it was doing in every once in a while, I reseated the card, and for the most part, it would go away on the first try, then it started progressing worse, until my new case and PSU, where it is just dead. I sure hope its not dead, but dont rule it out.
 

Read other 3 answers
RELEVANCY SCORE 44

I have an ATI AIW 9800 (with a TV tuner). It needs power from my PSU (cheap 350W PSU: +5V/35A, +12V/17A, +3.3V/14A)
Sometimes when I switch my computer on it starts beeping and telling me to
re connect the power to the Radeon. When I look at the plug, the end where
the red wire (+5V) is has gone totally black and is burnt out. I've already
ruined the only two floppy style power connectors on my psu and now I've
started using molex convertors but I'm getting through those pretty
quickly!
Anyone have an idea what might be causing this? The +5V pin on my 9800 is also oxdized, what should I do with it? sandpapers?

My computer is
CPU: P4 2.4GHz (Northwood)
Mobo: ASUS P4S533-MX

Is it possible the 4X AGP slot is the cause of the problem? Since the signaling voltage of AGP 4X is 1.5V while that of AGP 8X is 0.8V. However, I've checked that 9800 should work in 1.5V, 4X.
There's another strange observation: I connect the power connector from computer 1 (a PSU connected to a P2 Mobo only) to my card in computer 2, to see if it's the problem with overloaded PSU. I turned on computer 1, then computer 2, it boot normally. Today I accdentally switched the PSU of computer 1 off, guess what? its fan kept blowing! It happens that the power comes from my AGP slot in computer 2 to that PSU.
If it's the case, I think the problem is due to "backflow" of electricity from the AGP slot to PSU...just guessing

Anyone have any idea... Read more

A:+5V wire of 9800SE AIW Burns in 2 minutes

Have you checked the voltages on your PSU? while it is certainly possible that your mobo is defective. the first thing that would come to mind to me would be defective PSU.
 

Read other 2 answers
RELEVANCY SCORE 43.6

So heres the thing. I am a keen gamer, I especially like first person shooters but I have noticed that newer games are not running as smoothly as I would like. eg. Deus Ex 2. I am thinking of getting a Radeon 9800SE 128mb. Will I see a dramatic increase in my grapical performance with this card, especially Frame rates, compared to my present card listed in my sys spec.
Maybe someone has the 9800 SE or even upgraded to it from the 9000 pro.

Cheers Guys!
 

A:Radeon 9000 pro 64Mb V's 9800SE 128Mb

Read other 6 answers
RELEVANCY SCORE 43.6

I bought the r98-sc3 card. now ive read some people that bought this card flashed the bios and got it to 9800pro mode.

the omega drivers softmod did not work for me. i got artifacts. is there any way that i can get my 9800se to a 9800pro without getting artifacts. im going to buy a vga cooler even if i cant softmod it, but i just wanna know if i can without getting artifacts
 

A:I need some questions answered about my Powercolor radeon 9800se

Flashing the BIOS wont help. If the soft modded driver didnt work, you got artifacts, that means 4 of the rendering pipelines are damaged or just wont work. Since that card has 256bit memory you will still get very good performance. There isnt a huge difference with the extra 4 pipes enabled. The first one I got didnt take the mod but luckily it went bad a few weeks later and the replacement card did mod. Deffinately get the VGA cooler. That card runs extremely hot.
 

Read other 1 answers
RELEVANCY SCORE 42.4

I have a ATI 9800SE 256bit and I need to update my drivers to a driver that will unlock the other 4 piplines on my card. Which driver is the best for XP and playing Half-Life 2 on?

Thanks
 

A:ATI Radeon 9800SE - Updated Driver Needed 2 Unlock Extra Pipelines

Use the latest "Omega" drivers- they inlcude an option to unlock the extra pipes upon installation. GREAT CARD! GREAT VALUE! :knock:
 

Read other 2 answers
RELEVANCY SCORE 38.8

I have read many places that MS SQL Server using Named Pipes is using port 139 and port 445. But I don't know when port 139 is used instead of port 445 and vice versa?

Are port 139 and port 445 actually duplicates?

I have limited knowledge in NT Networking.
 

A:Named Pipes, Port 139 and Port 445

Read other 6 answers
RELEVANCY SCORE 38.4

should I buy a powercolor radeon 9600 pro 128mb 128bit 400/600 (core,memory)
should I buy a powercolor radeon 9600pro 256 mb 128bit 400/400 (core,memory)
should I buy a powercolor radeon 9800se 128mb 128bit 375/450 (core, memory)
should I buy a "refurbished" sapphire radeon 9800pro 128mb 128bit 425/650

all of these are from newegg.com except for #1
 

A:9600pro-9800se-"refurbished" 9800pro

Read other 6 answers
RELEVANCY SCORE 34.4

Windows 7 reminds them of mac OS X

the layout anyways?

ya know the taskbar and all it definetlry reminds me of the first time i saw a macintosh os 10

A:Does anybody else thinks?

You mean the Mac might be copying Windows.

Read other 4 answers
RELEVANCY SCORE 34.4

I used a VPN in China because several things are blocked without it. Now I'm back home in London and my PC still thinks it needs VPN because it won't open up any page what so ever without it!

Does anyone know what's going on?

PS I use Windows 7
 

A:PC still thinks it needs VPN?

Did you uninstall the VPN software? You may also want to check you Internet Options in the Control Panel and look under the Connections tab. There's a button there for LAN settings, disable any of the proxy settings there, uncheck everything. Also check that you are not using DNS settings that are no longer valid. Set your Ethernet and wireless connections to automatic as shown in the screen shots here: http://windows.microsoft.com/en-ca/windows/change-tcp-ip-settings#1TC=windows-7
 

Read other 1 answers
RELEVANCY SCORE 34.4

I was updating drivers and firmware on our SCSI/RAID cards yesterday, and a weird thing happened. After I was done, I started making sure my data was still intact. I double-clicked on one of my drives, and it started the 'autoplay' routine. Just as if it were a CD drive. All the data is there (thank goodness), and I can get to it by exploring, but whenever I double-click I get a message telling me that 'maxviewf.exe' in missing.

I recognize the EXE. It's on several CD's I get. It is the name of a viewing program. I've trying rebooting, but it still is there.....

Weird...

System stats:

DELL PE2400
Windows 2000 server (Service pack 1)
PERC 2/si (RAID controller - embedded)
PERC 3/dc (RAID controller - PCI card)
 

A:HD thinks its' a CD?

Check the root directory of the hard drive for a file called "autorun". If you find one delete it and you should be OK.
 

Read other 2 answers
RELEVANCY SCORE 34.4

Hi. i have just reformated my dirves and installed xp now when i go to the browser and click a blank cd R that i wont to burn using xps feature for doin that it doesnt let me i tried updating the driver for it but it doesnt work please helpp thanks.
And im not sure of the make of cd re writer as it was bought with the computer.
Thanks please help
 

A:My Cd RW thinks its a CD rom

Read other 6 answers
RELEVANCY SCORE 34

My MAC thinks it is in Germany. Youtube ads are in germany, google goes to Germany google, responses on comments are in german. What happen all of a sudden so that this occurs. Does NSA have my IP crossed Circuit. Th problem is not with iTunes, toolbars.
Iam in Costa Rica.
How did this happen in the first placed. Is all of my data and activity being recorded in Germany?
 

A:I am in Germany? My MAC thinks so.

Read other 6 answers
RELEVANCY SCORE 34

I am using XP Media Centre, AOL for my BB access over a Netgear router.

I just reinstalled my Dell Dimension 3100 and since then cannot access my Napster service, or listen to BBC Radio football matches. In both cases it says I am not in the UK so cannot use the service. As I sit here in deepest Hampshire, England I have to wonder WTF??!!

My Regional Settings say English / UK all over them, including text input etc. This happens in all browsers. i.e. AOL, Opera, FF, IE. I am using McAfee Security Centre.

Basically I have not installed any 'new' software on the reinstall so cannot understand what is happening. AOL were dead useful, saying I should reinstall my Firewall and AOL!

ANY help at all will be greatly appreciated.
 

A:My PC thinks it is in another country

Read other 12 answers
RELEVANCY SCORE 34

OK here is a big one

when i try to goto hotmail.com the webpage says to i need to have ie4 or higher to use hotmail............ im running ie6

when i goto yahoo launch...... it says your netscape is not valid
when i goto yahoo launch...... it says i need a higher version of netscape

i just cannot understand why this is happening to me im running IE6
windows xp

but heres the big laugh i formated my system (after ghosting it) then put the recovery disk in and started from fresh (the way it was when i first got it)
goto microsoft to get all the updates but i cant because a box comes up after 5 mins saying it will shut dowm in 1 minute then it procedes and do a count down to 0 then forces a reboot

is there a way out of this please help ?

things i have done
search registry for missed place netscate the regfix
scan for viruses none found
down loaded all new updates
tried a fresh reinstall but i get timed out after 5 min
logged as administrator in safe mode but most of the above still happens

man this is getting real bad
please help

by the way the last time i used netscape was hhhhmmm 4 years ago on a different machine

lost fingers
 

Read other answers
RELEVANCY SCORE 34

Everex Stepnote Windows XP sp3 Iphone 5 ios 8.1 hotspot connection issue
Hi,

I'm trying to use a iPhone as a wi-fi hot-spot. It comes up in the list of Available Wireless Networks, but when I try and connect it comes up with...

"Windows is unable to connect to the selected network. The network may no longer be in range. Please refresh the list of available networks, and try to connect again"

Have updated all drivers, updated all Windows components, cleaned registry, defragged drive, and spyware removal just for good measure.
Have noticed wireless connection keeps jumping to OPEN Shared, WEP connection when should be WPA-Personal.
Any fixes would be better than none,
Am using my laptop to access this site, there for not able to Download TSG Sysinfo for laptop with problem.

Any suggestions would be good

Thanks.
 

A:Apple a Day?Me thinks not!

Are you connecting your iphone with your computer with the usb connector.
 

Read other 2 answers
RELEVANCY SCORE 34

My MSN messenger got corrrupted and possibly IE as well, due to something that was attached to a bogus email security notice. MSN wanted me to use "Housecall" to scan for a virus,
since everything that they asked me to do still would not allow me to reinstall MSN7. Since all that I can use now is IE and it is so slow that the program kepts aborting. I downloaded this one instead and have attached the log. Can you please tell me which is any of those listed should remove?
ogfile of HijackThis v1.96.1
Scan saved at 2:55:25 PM, on 8/21/03
Platform: Windows 95 B (Win9x 4.00.1212)
MSIE: Internet Explorer v5.51 SP2 (5.51.4807.2300)

Running processes:
C:\WINDOWS\SYSTEM\KERNEL32.DLL
C:\WINDOWS\SYSTEM\MSGSRV32.EXE
C:\WINDOWS\SYSTEM\MPREXE.EXE
C:\WINDOWS\SYSTEM\mmtask.tsk
C:\WINDOWS\EXPLORER.EXE
C:\WINDOWS\LOADQM.EXE
C:\SCANJET\PRECISIONSCANLT\HPPWRSAV.EXE
C:\WINDOWS\SYSTEM\RNAAPP.EXE
C:\WINDOWS\SYSTEM\tapiexe.exe
C:\PROGRAM FILES\INTERNET EXPLORER\IEXPLORE.EXE
C:\WINDOWS\SYSTEM\DDHELP.EXE
C:\WINDOWS\DESKTOP\HIJACKTHIS\HIJACKTHIS.EXE

R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://www.ask.com
R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Search Page = http://ask.com
R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://ask.com
R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Search_URL = http://ask.com
R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Local Page =
O2 - BHO: (no name) - {53707962-6F74-2D53... Read more

A:MSN thinks I might have a virus

TrishConjure Hi

Close all IE and Explorer windows and have those items checked:

O16 - DPF: {74D05D43-3236-11D4-BDCD-00C04F9A3B61} (HouseCall Control) - http://a840.g.akamai.net/7/840/537/...all/xscan53.cab
O6 - HKCU\Software\Policies\Microsoft\Internet Explorer\Control Panel present

Hewlett Packard always clutters computers with unwanted and unneccessary items This is one of them :

O4 - HKLM\..\Run: [hppwrsav] C:\SCANJET\PrecisionScanLT\hppwrsav.exe

***HP Power Save background task for the HP ScanJet 3200C. The original version of the Windows 95/98 drivers would cause the PC to freeze for 3 to 8 seconds several times an hour, would cause Internet disconnection, or would have the mouse freeze occasionally.

Recommendation :
If you have a ScanJet 3200C and experience the above problems, either download and install this patch, or download the very latest drivers which should be dated at least January 2002.****

Then go HERE and download AdAware6 181 and scan with that. When installed run the webupdate to get the latest reference-file.

Then........

Make sure the following settings are made and on -------"ON=GREEN"
From main window :Click "Start" then " Activate in-depth scan"

then......

click "Use custom scanning options>Customize" and have these options on: "Scan within archives" ,"Scan active processes","Scan registry", "Deep scan registry" ,"Scan my IE Favorites for banned URL&q... Read more

Read other 2 answers
RELEVANCY SCORE 34

I am new to this forum and not good with logs of any sort...i have spyware and the like but recently got hijack this...which i don't know how to read...
I am having problems trying to type things into search fields on IE...it just reloads the page to a blank page and the whole thing flickers...the status bar with the address flickers and you can't type anything...i ran hijack this...and this is the log, can someone please help me???
Logfile of HijackThis v1.99.1
Scan saved at 8:20:08 AM, on 21/07/2005
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP2 (6.00.2900.2180)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\Common Files\Symantec Shared\ccProxy.exe
C:\Program Files\Common Files\Symantec Shared\ccSetMgr.exe
C:\Program Files\Norton Internet Security\ISSVC.exe
C:\Program Files\Common Files\Symantec Shared\SNDSrvc.exe
C:\Program Files\Common Files\Symantec Shared\SPBBC\SPBBCSvc.exe
C:\Program Files\Common Files\Symantec Shared\ccEvtMgr.exe
C:\WINDOWS\system32\LEXBCES.EXE
C:\WINDOWS\system32\LEXPPS.EXE
C:\WINDOWS\system32\spoolsv.exe
C:\Program Files\Norton Internet Security\Norton AntiVirus\navapsvc.exe
C:\Program Files\Common Files\Symantec Shared\CCPD-LC\symlcsvc.exe
c:\Program Files\Common Files\Symantec Shared\Security Center\SymWSC.... Read more

A:Please help?? thinks i have a hijacker

can anyone help??? please???
 

Read other 3 answers
RELEVANCY SCORE 34

I have hp pavilion 6244 PC with a HL-dt-st-dvd rrw gsa hL30. I am running Vista Home Preminum 32 Bit.

My problem is this it won't play any store bought dvds or burn anything any more.

It will play a video I burn with it previously before this happen and cd if if play the song from picking them but not picking play an album.

I have checked bios that's good
I have reinstalled the driver several times
The device manager say it is just a cd rom and I have tried playing in safe mode and still look at the device manager and it says it is just a cdrom.

I have tried everything on HP's Mr fix it with nothing fixing it .
I would understand that their something wrong with the dvd player other then I can play dvds burned on it from previous days.
When I run mr fix it it doesn't say anything except that the media I put in it is not the correct media for fixing the problem.

Any body got any ideas to try next????????????????????

A:Dvd burner thinks it is a cd rom

When you right click the drive in Device Manager and click Properties what's it say in DVD Region tab?

Also try burning something with Imgburn See what it gives for an error message.

Read other 17 answers
RELEVANCY SCORE 34

OS: Win7 Ultimate
Office: Pro Plus 2010 downloaded from TechNet
App: Word 2010
I have a hyperlink in a word .docx document. When Ctrl-clicking on the link, I get the MS window saying that MS security essentials is not supported in my country. Made 100% certain--country code is set to US-en.
Can feed link directly into my browser and am sent to correct site.
Copy & Paste from Word doc:
Microsoft Security Essentials
Install MSE --> http://www.microsoft.com/security_essentials/
Here is a snip of where I land:

A:MS thinks I'm in another country

  
Quote: Originally Posted by karlsnooks


OS: Win7 Ultimate
Office: Pro Plus 2010 downloaded from TechNet
App: Word 2010
I have a hyperlink in a word .docx document. When Ctrl-clicking on the link, I get the MS window saying that MS security essentials is not supported in my country. Made 100% certain--country code is set to US-en.
Can feed link directly into my browser and am sent to correct site.
Copy & Paste from Word doc:
Microsoft Security Essentials
Install MSE --> http://www.microsoft.com/security_essentials/
Here is a snip of where I land:



Try clearing your browser cookies

Read other 6 answers
RELEVANCY SCORE 34

Whenever I try to view a streaming video the buffering bar starts out nice and slow, and then starts doubling itself! Soon it's up to 100% and the movie starts. In about 6 seconds the play bar has allready caught upto itself. I can't just press pause and wait for it to load either because it's a streaming video . So any help would be great.

Derek

A:Help my computer thinks it's better than what it is!

Try opening up Windows Media Player and going to Tools>Options. There should be a tab on there that deals with buffering or internet connections. On this tab you should be able to adjust the time allowed for buffering or the speed of your connection. You may want to specify a minimum time for buffering in this tab.

BMR777

Read other 1 answers
RELEVANCY SCORE 34

For some reason whenever i use google or ebay or that junk it registers me as from the uk. So i guess its been configured somehow. ANy help? im using internet explorer.
 

Read other answers
RELEVANCY SCORE 34

I posted in error where I it says widows is loading files and goes to start up repair 4 days ago and haven't got any response, so I think this might be my problem after I got this info on the error I get. Other than, when I run bootable MiniTool Partition Wizard it just loads for about 10 seconds and my laptop restarts. I had a secondary OS with a GRUB boot menu until I replaced it with bootrec.exe on cmd.exe in the startup repair thinking it'll fix my problem.
I want to fix my computer with out getting anything deleted if possible, I have no repair/installation disc nor do I have restore points.

Startup Repair diagnosis and repair log
---------------------------
Number of repair attempts: 1

Session details
---------------------------
System Disk = \Device\Harddisk0
Windows directory = E:\Windows
AutoChk Run = 0
Number of root causes = 1

Test Performed:
---------------------------
Name: Check for updates
Result: Completed successfully. Error code = 0x0
Time taken = 15 ms

Test Performed:
---------------------------
Name: System disk test
Result: Completed successfully. Error code = 0x0
Time taken = 0 ms

Test Performed:
---------------------------
Name: Disk failure diagnosis
Result: Completed successfully. Error code = 0x0
Time taken = 172 ms

Test Performed:
---------------------------
Name: Disk metadata test
Result: Completed successfully. Error code = 0x0
Time taken = 15 ms

Root cause found:
---------------------------
... Read more

A:Windows 7 maybe thinks it's on (E:) and not (C:)

Boot into System Recovery Options to confirm that Win7 or it's System Reserved boot partition (Preferred if you have it) is Partition Marked Active.

Then run Startup Repair - Run 3 Separate Times until Win7 starts.

If these steps fail then start and the top with the steps for Troubleshooting Windows 7 Failure to Start

Read other 9 answers
RELEVANCY SCORE 34

I am running xp with sp1. At least that is what my computer says, however, when I try to install some programs such as media player it tells me I must have windows xp. Microsoft website will not let me upgrade to sp2 because it thinks my computer is not compatable and various other issues like this. I tried to download a patch, I don't remember which one, and it told me that the patch was not available on a server edition of windows. I should not have a server edition. I am very confused. I ran several anti-virus and AdAware came up clean, however MWAV escan shows trojans and keyloggers over and over even after it says it has deleted them.

Here is a hijackthis log: Does anyone have a clue?
Logfile of HijackThis v1.99.1
Scan saved at 11:22:57 PM, on 10/14/2007
Platform: Windows XP SP1 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP1 (6.00.2800.1106)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\EarthLink TotalAccess\FastLane2\IPMon32.exe
C:\Program Files\Bellsouth\HelpCenter40b\bin\sprtcmd.exe
C:\Program Files\Winamp\winampa.exe
C:\Program Files\iTunes\iTunesHelper.exe
C:\Program Files\Java\jre1.6.0_02\bin\jusched.exe
C:\PROGRA~1\INCRED~1\bin\IMApp.exe
C:\Program Files\Lexmark X125\LEX125SU.exe
C:\Program Files\wmconnect\wmtray.exe
C... Read more

Read other answers