Over 1 million tech questions and answers.

Multiple BSODs after unplugging and plugging in flash drive.

Q: Multiple BSODs after unplugging and plugging in flash drive.

Dual Core Windows 7 Pro 64 bit Toshiba laptop. My daughter was working on a Power Point project for school. She went to plug in her flash drive and it didn?t seem to load the drive up. She unplugged it and then plugged it back in. We got a BSOD. We restarted it and it BSOD again. I tried some general troubleshooting, including restoring it to a previous version, and now cannot get into Windows at all. Not even in safe mode. Now I am getting multiple BSODs.

Currently I am seeing these BSODs:


I am getting one when just trying to start and run windows I am getting a BSOD about memory management.


If I try to go into safe mode it loads the files and then I get a BSOD regarding the fbwf.sys.
Using the Windows 7 disc I have been able to get to the System Recovery Options. It finds my install and then blue screens with IRQL_NOT_LESS_OR_EQUAL or Driver_IRQL_NOT_LESS_OR_EQUAL even before it gets to finding my install.


Other BSODs I know I have seen are regarding the Ntfs.Sys and PAGE_FAULT_IN_NONPAGED_AREA.

I was able to run a mem test on it at one point and it said everything was fine. I would appreciate any help or advice you can give me since I can?t even get to a command prompt or safe mode.

RELEVANCY SCORE 200
Preferred Solution: Multiple BSODs after unplugging and plugging in flash drive.

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: Multiple BSODs after unplugging and plugging in flash drive.

If you would like for us to be able to effectively help you, we will need you to follow the Blue Screen of Death (BSOD) Posting Instructions Please be sure to do each step, as outlined in the tutorial. By doing this, we will have the necessary information to help you.

Read other 1 answers
RELEVANCY SCORE 72.8

Getting ready to do the install on my new SSD with some trepidation. I have Raptors in Raid 0 right now and would like to simply unplug them, set the BIOS to AHCI and use the 0 port for the SSD experiment/potential fiasco. What I hope to be able to do if the SSD doesn't like me, is to unplug it, set the BIOS back to Raid, plug in the Raptors and pretend the whole thing never happened. Does this stand a chance of working?

A:Plugging and Unplugging!

I wouldnt unplug the raptor raid - if you use intel raid (the one i'm sure of and probably similar, or the same for others) when you enable raid in the bios it also enables AHCI - so you should be good to go with testing the ssd drive - just unplugging a raid array can be very hard to set up again - i did it years ago and it was a miracle i got it back up and going again (that included reinstalling the OS) so not recommended - it also depends what options are available in the raid rom (i think its called) which you set it up in before you install the OS. From memory, which is bad, the problem was it couldnt recognise one or both the drives.
It depends on your motherboard I guess but for mind it should be ok - running raid and using the same controller to use a ssd drive in AHCI mode - but treat this as my opinion - you should be able to find information on your motherboards site, or intel etc's, site. Or wait for more replies as Im uncertain and more repies means more suggestions.
If it has 2 controllers eg intel and jmicron use the JMICRON if it supports AHCI to be on the safe side.

Read other 3 answers
RELEVANCY SCORE 72

Hi everyone, hope this is a good year for all. I just picked up a new computer running xp. It came without a floppy drive, so I picked up a portable external usb floppy drive. Is it ok to plug in, and unplug the floppy to the usb port with the computer on? Thanks for the tips/advice.

Regards
IMP49
 

A:Plugging in and unplugging a usb device

Read other 8 answers
RELEVANCY SCORE 71.2

Hi, just bought the 2-1 laptop last week. I want to enable a notification sound while plugging in the charger and also when I'm unplugging it. I've checked the device sound properties but don't seem to find it. Please help ! vsen

Read other answers
RELEVANCY SCORE 71.2

Hey guys. I ran into a little problem recently, and would like to share it.
I know it is supposedly ok to plug USB cables in and out while the computer is on, but, to be safe I have always gone through the Safely Remove Hardware icon.
For some reason, though, I have always felt it is safe to just plug sound devices in and out with no regard to whether the computer is on or not. Have done this for years.
However, I noticed a few days ago that one channel of my onboard sound line input had quit, on my newest MB. I did not realize this for awhile, because somehow the system had just rerouted the one channel into both sides, when writing to the CD or DVD. (I noticed that Joe Walsh appeared to be playing an unplugged guitar on the Eagles Hell Freezes Over concert after transferring from my old VHS tape to DVD, even though both speakers were working! LOL)
Anyway...I fixed the problem by just installing a sound card. (by the way, even a cheap $14.00 sound card is at least as good as most onboard sound: mine sounds much better than the original.)
So, would you guys advise having the computer turned off, even to plug in headphones, for instance?
 

A:Plugging/unplugging sound devices

No, 1/8" jacks can freely be plugged/unplugged while the computer is on, and when you're outputting sound.
As to why the jack went dead, cou÷d've been just natural death of age, removing the plug at an extreme angle and damaging the jack, etc...
 

Read other 1 answers
RELEVANCY SCORE 71.2

My problem is this, my motherboard is Biostar TP67B and I have downloaded the sound drivers from the manufacturer website which is realtek high definition audio.However, If i had left my headphone plugged into my front panel jack and when I restart my computer, the headphone icon keeps flickering saying its plugged and unplugged constantly when it is in fact plugged in. I had tinker around a little bit and I have no idea how to fix this problem now. Its going bad to worse as it unplugs itself randomly now. I'm trying to go for a full reinstall of my sound drivers.

A:Headphones Plugging and Unplugging constantly bug

Have you tried a different headphone? Maybe the headphone and not the PC or headphone jack.

If not the headphone, check the connection from the front panel at the motherboard, May be a bad connection there. Reseat (unplug then plug back in) the connector at the motherboard. If it still has problems I would suspect the front panel headphone jack, or the wiring.

Read other 9 answers
RELEVANCY SCORE 71.2

Everytime I plug or unplug my charger from my notebook, the brightness keeps changing?!?!?  Its very irritating and I've tried everything to try to fix it including going to the advanced power settings and turning off the "enable adaptive brightness."  Nothing has worked, please advise.

Read other answers
RELEVANCY SCORE 70.4

Hi all,

Acer 7740g, Windows 7 HE.
I have this annoying problem that when my AC power is plugged or unplugged it makes a beep.
Muting the sound completely helps, but that's sometimes not an option.

I tried the following and no luck:

Editing a registry entry HKEY_CURRENT_USER\Control Panel\Sound\Beep and changed it to "No".
Uninstalling the Beep device from my device manager.
Turning off my pc speaker, unfortunately, I didn't find where I can disable it.

My sound card drivers are: Realtek 6.0.1.5969

Anyone has another idea?

Thanks.
 

A:Annoying beep when plugging/unplugging AC Power

This forum is for "Business Applications", not hardware problems.
Please post on the correct forum which is "Hardware" here: http://forums.techguy.org/19-hardware/
 

Read other 2 answers
RELEVANCY SCORE 70.4

Is it safe to unplug my mouse and then plug it back in again into it's USB port without shutting down my laptop?

Is it safe to plug in my laptops power cord while my laptop is running without shutting down first?
 

A:Plugging in and Unplugging cords while laptop is running?

Yes and yes, except if you are going to unplug the power cord do it from the wall socket first and be sure you have plenty of charge on the battery.
 

Read other 2 answers
RELEVANCY SCORE 70.4

Hi all,

Acer 7740g, Windows 7 HE.
I have this annoying problem that when my AC power is plugged or unplugged it makes a beep.
Muting the sound completely helps, but that's sometimes not an option.

I tried the following and no luck:

Editing a registry entry HKEY_CURRENT_USER\Control Panel\Sound\Beep and changed it to "No".
Uninstalling the Beep device from my device manager.
Turning off my pc speaker, unfortunately, I didn't find where I can disable it.

My sound card drivers are: Realtek 6.0.1.5969

Anyone has another idea?

Thanks.
 

A:Annoying beep when plugging/unplugging AC Power

Read other 8 answers
RELEVANCY SCORE 70.4

Hi all,

I'm at a dorm room with cable internet. It usually works fine, but now if I unplug it, then plug it back, the computer doesn't connect to the internet anymore. Sometimes it says it's acquiring network address, but that doesn't change. The computer connects to the internet fine if I turned on the computer with the cable already plugged in.

Another computer doesn't have this problem with the same cable, always able to connect after being unplugged/plugged. Both computers are on Win XP.

I suspect the Windows firewall has something to do with it, if only because it is turned on the the problematic computer, and not on the other one. I couldn't turn it off, however, because it doesn't let me open up Windows Firewall Settings, giving me the message that the "associated service is not running" and whether or not I could like to start it. If I click "Yes", it simply says it "cannot open Windows Firewall/Internet Connection Sharing service".

Please let me know what the problem might be and what i can try to get it working again. I hope I haven't given too much useless information.. haha. Thanks!

Dave
 

A:can't connect to internet after unplugging then plugging cable

Read other 13 answers
RELEVANCY SCORE 70.4

I want to disbale the beep tone that sounds when plugging / unplugging the charger. I tried all the methods I could find online, but either those options are not available in this model or did not work. Please guide me in this regard. Its really annoying and distracting in a library or classroom setting. The OS I am running is Windows 8.1.

Read other answers
RELEVANCY SCORE 70.4

Hello, I've noticed that my computer crashes everytime i unplug or i plug in and USB drive. Today I bought a new USB mouse and when I connected it no crashes were seen, but when my pc installed the last driver, the BSoD appeared once again. I'm using Win7 64b and I really don't know what can I do, I've tried everything like uninstalling all USB drivers and recreate the INFCACHE.1 file, but still nothing. What can I do to solve this?
Thanks in advance.

A:BSoD when plugging/unplugging USB and when installing USB drivers

1) Does it happen with all usb devices or only the mouse?
 
2) Does it happen with all usb ports?
 
3) Does it happen in safe mode?
 
4) Look in device manager - are there any yellow or red symblos?
 
5) Download and install the newest chipset driver for your system. If it's a laptop, get it from the website of your laptop manufacturer. If it's a desktop, you can get it from either the desktop or the mobo manufacturer's website.
 
6) Look for a bios update.

Read other 5 answers
RELEVANCY SCORE 70.4

Hi. I have problem with my mouse and keyboard, they are unplugging. I read many tutorials here, but nothing helped me. Mouse and keyboard are randomly unplugging and plugging, but after this they are unplugging and I must restart computer. Its ridiculous because usb headphones are working. Problem started when I had Windows 8.1, after I formated to 7, now I have 10, and problem is still. I tried some other mouses and keyboards, but didn't helped. I changed some hardware, but didnt helped too. I found something strange. My standard mouse and keyboard are turning off and I must restart computer, but new set is unplugging and plugging sometimes before turn off. Help me please (sorry for my english)

My pc:
cpu: i7 2600k with box cooler
mobo: Asus Maximus IV Extreme-z (before I had ASRock p67 pro3 b3)
gpu: Gtx 660 Msi (before Radeon R7 260x oc)
hdd: Seagate ST1000DM003 and Seagate ST500DM002
psu: Thermaltake smart se 530w (before chieftec gpa-500s8)
case: SilentiumPc gladius 800
ram: 6gb - 2x2gb samsung 1x2gb kingston
 

A:Win7/8.1/10 Mouse and keyboard is unplugging and plugging

Have you made sure that you have the latest drivers for your motherboard? Also what keyboard and mouse? And are you getting any notification on screen when they disconnect?
 

Read other 2 answers
RELEVANCY SCORE 70

I have the Hyperx Cloud and the microphone easily unplugs from the headphones so that you can choose to not have a mic some times. While I was talking with my friends on skype and needed to mute the mic quickly so I just pulled out the microphone and when i plugged it back in it didn't work. I have googled many solutions but nothing seems to work.
 

A:Simply unplugging my headphones and plugging them back in seemed to break them. HELP!

Do the speakers still work after you have unattached /reattached the mic?

Presuming you are running Windows (as you haven't specified)

Open control panel, then open Sound (depending on your OS and view options you may need to click on the Hardware and Sound option first or similar)

In the sound window, click on the Recording tab.

With the Mic attached how many devices do you see?

Is the Mic on your headset set as Default?

If you remove the mic and reattach (with the sound window open) does the mic get recognised and show back up in this list?

Does it remain as default / enabled?
 

Read other 1 answers
RELEVANCY SCORE 70

I have a Dell Vostro 1400 running Vista Home Basic and have had two periods in the laptop's existence where it would mysteriously freeze. You could see everything on the screen, and the power lights were on, but it would not respond except to a hard reboot by holding the power butting down for 5 seconds.

I am going through one of those periods now, and have discovered that the problem happens when I am either plugging or unplugging the AC power adapter, but don't know why. I have been all over the web for a solution, and while it does seem I am not alone with this problem, I have not read a sensible solution yet. My favorite bad answer is "don't unplug your laptop when it's on."

So, does anyone know what it could be? I wanted to look at system logs, and so went into the Event Viewer not even sure what to look for, but didn't see anything that looked like a likely culprit. Please help!

Thanks,
Neil
 

A:laptop freezes when plugging and unplugging AC power adapter

being a member of the Dell Community Forum, I looked there and found this

A lot things happen in Windows when inserting the AC power adapter.

To check if it's a classic CPU lock-up: repeatedly press capslock. If the capslock light doesn't change, there's no live in there.

Assuming the CPU is locked up: It's possible there's a log entry in the system log just before the AC power adapter is inserted. These entries give clues where to look, just before things went sour.

Next try to reproduce it in Safe Mode (press F8 when Windows start) If it's also in Safe Mode - try running an alternative OS (no need to install)

If the problem also shows up here - most likely it's a hardware issue.

Otherwise it's a windows issue - might be driver related.

the "alternate OS thing is a link on the forum web site. Click here to go to that site.

Hope this is some help... Raybro
 

Read other 1 answers
RELEVANCY SCORE 70

When I plug in my laptop to charge the laptop turns off, and when I unplug the charging cord from the computer it turns off. Does anyone know whats going on? I have an Inspiron 15 5558.

A:Laptop turning off when plugging or unplugging in charging cord

Hi DNGUYEN2252,
Are you using an original Dell OEM Adapter? When you plug in the adapter to the system, does the adapter stay firm or does it fall off easily? Is the adapter frayed? Is there any damage on the system?
Does the adapter led stay on and stable or does it go off when connected to the system?
Disconnect the adapter and battery and press and hold the power button for 30 seconds to release any static power. Then try connecting with the adapter only / battery only.
I would first suggest you to try with another power adapter. The current one in use might be shorting the system and hence the system powers off.
If another adapter works fine, then replace the adapter. If the other adapter  also exhibits the same behavior, then replace the DC port - this is the part you would need - http://bit.ly/2kZR8go
If nothing works, I would suspect a faulty motherboard. 
If there is no warranty, then you could contact our team to get a quote for a paid service call - http://dell.to/1vnT6CQ
Also, please click my DELL-username and write me a private conversation with the service tag and your contact details(Name and Email) for case records.
Let us know if you have any other queries.

Read other 1 answers
RELEVANCY SCORE 70

I was wondering if anyone is familiar with a method to enable sounds for when you plug in or remove a charger connected to your laptop. It is not a problem with my pc, but is an option that is not available for me which i would like to install to let me know if i accidentally unplugged the charger, particularly if I'm working on a full-screen feature. Any help would be appreciated.
I have Windows 7 home Premium 32-bit installed.

A:How to enable sound when plugging/unplugging charger for laptop.

In the System Sounds, there is an option for device connect or disconnect. This will probably do what you want. You will have to assign a sound for those functions.

The System Sounds panel can be accessed from Start/Control Panel/Hardware and Sounds. Click on "Change System Sounds".

Read other 2 answers
RELEVANCY SCORE 70

Hello I just purchased my lenovo x280 and have noticed whenever I plug or unplug the power the display flickers and goes black for less than a second then resumes like normal, this happens every time I plug or unplug the device. I saw similar posts about this being because it changes the refresh rate on a different laptop but I haven't been able to find the setting to turn it off

A:Screen flicker on x280 when plugging and unplugging from power

Hello and welcome,
 
Right click on the desktop background.  Select Intel Graphics Settings.  Select Power.  Disable Display Refresh Rate Switching.
 
I didn't know where to find it either until just now.  Thanks for getting me looking.  I'm going to leave it as is on my X280 to maintain whatever battery run-time the 48Hz setting saves.
 
Z.
 

 

Read other 2 answers
RELEVANCY SCORE 70

Hello I just purchased my lenovo x280 and have noticed whenever I plug or unplug the power the display flickers and goes black for less than a second then resumes like normal, this happens every time I plug or unplug the device. I saw similar posts about this being because it changes the refresh rate on a different laptop but I haven't been able to find the setting to turn it off

Read other answers
RELEVANCY SCORE 70

Hi All! Been a while since I've posted, but sitting here reading other's posts, I almost forgot why I logged in!

I have a weird problem with my computer.....a little background:
I didn't turn the computer on for a LONG time....perhaps a year, so one day, I decided to boot it up and it won't boot past the post! So I replaced the MB battery, checked the power supply, replaced the memory...and it booted. But then, I turn it off, and it won't boot again...same problem with it not booting past the mem. post. So being that it was an old computer, I figured I'd just build myself a new machine and use the hard drive as a slave. There are programs on the drive that I want to use that I cannot replace! Well, I tried doing that, but the new computer won't see the drive....it won't even boot with it plugged in. So....

I take the hard drive to another machine that I know works fine, and it boots. Problem solved....so I thought. I turn it off, and try and turn it back on.....nothing.....no beeps, no post....nothing. So I tried changing the power supply, and plug all back in, and it boots. Turn it off, nothing. Long story short, if I unplug the motherboard power cord from the board, and plug it back in, it boots, but if I turn it off, I have to repeat the motherboard plug thing to get it to boot again. I have had the drive checked for viruses, and it's clean.
I have to admit, I am stumped! Any ideas? Any suggestions would be greatly appreciat... Read more

A:Computer won't boot without unplugging and plugging motherboard power

Read other 6 answers
RELEVANCY SCORE 69.2

the subject says it all.brand new t520 with optimus (nvidia+intel) display adapter, 1920x1080 screen.whenever i plus in or unplug power, the display blanks for about 2 seconds, then flashes back on.the problem occurs whether the bios setting is integrated, dicrete, or optimus, and th problem occurs even if the display settings are the same in power profile for AC and battery. is this normal? it is very BAD. thanks in advance.george













Solved!

Go to Solution.

A:t520 display blanks and flashes when plugging/unplugging ac power

hey ghoffman,uninstall the current graphic driver that you have. let windows install its own generic drivers.once generic driver has been installed, test again and see if the problem occurs. If it does not, continue by going to our support site via http://support.lenovo.comdownload the latest graphic driver for your unit, install it and test again.





WW Social MediaImportant Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.Did someone help you today? Press the star on the left to thank them with a Kudo!If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! Follow @LenovoForums on Twitter!Have you checked out the Community Knowledgebase yet?!How to send a private message? --> Check out this article.

Read other 5 answers
RELEVANCY SCORE 69.2

Urgh. Typical.

Install new case fans after moving 2 HD cages from the front of Corsar 600T case.
Check they run ok. Fine.
Put HD cages back in, one in the space on the bottom of the case beside the PSU.
Fight with the cables to get the HDs connected and the modular PSU cables back into the PSU.

- Attempt to power on. Nothing.
- Check cable, try another power cable. Nothing.
- No fans, no lights, nothing.
- No 'electrical sound' when flipping the switch on the back of the PSU.

Seems I have a 7 year warrant on the PSU and its only about 3 years old. But Corsair RMA system insists that you "try another PSU to verify the problem is the PSU" which is fair enough so off to buy another PSU, probably another Corsair. Hope the RMA system allows for refund rather than replacement, otherwise I'll have 2 PSUs which isn't really much use. I guess I can use this as an opportunity to upgrade to a bigger PSU since 7970 CF, 3 HD, 2 SSD, i7 2600K @ 4.7Ghz, a powered device connected to almost every single USB port is probably getting towards it's limits. I can then stick any replacement HX750 on Ebay or something...
 

A:Corsair HX750, dead after reseating and unplugging, re-plugging cables

Arris said:





Seems I have a 7 year warrant on the PSU and its only about 3 years old. But Corsair RMA system insists that you "try another PSU to verify the problem is the PSU" which is fair enough so off to buy another PSU, probably another Corsair.Click to expand...

I didn't have any fuss with my Corsair RMA request, when I mentioned using a Power Supply Tester.
 

Read other 3 answers
RELEVANCY SCORE 68.4

One of my customers reported that they plugged in a usb flash drive and the system blue screened. It took several restarts to get to a useable state. I checked the event log and took a look at the mini dump files and it looks to me like it might be a video or network driver issue (rather than a usb issue). I am hoping however that someone here will take a look and see what the logs tell you before I schedule time with the customer to try to resolve.
I scanned the system (and aforementioned flash drive for viruses - found nothing). The system for now however is stable again with no blue screens since last Friday.
The system is a Dell Precision Workstation T1650/Windows 7 Pro 64 bit/12 GB RAM/Sorry I don't have the processor but have to assume it's a 3rd Gen i7/Norton Internet Security/Dual monitors/ - please let me know if you need me to get other specs for you.
They run Solidworks 3D Cad software on this station.
I've attached the diagnostics file from the SF diagnostic tool.
I've also attached the mini dump files from the PC - just to be thorough

Thanks in advance for any insights.
Elly

A:BSOD when plugging in flash drive (red herring?)

Hi there,

Most of your dumps are pointing to a network driver,

That is going back to Sept. 2013.


Code:
Unable to load image \SystemRoot\system32\DRIVERS\e1c62x64.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for e1c62x64.sys
*** ERROR: Module load completed but symbols could not be loaded for e1c62x64.sys
Probably caused by : e1c62x64.sys ( e1c62x64+a8c3 )

Followup: MachineOwner
Driver Reference Table - e1c62x64.sys



Code:
start end module name
fffff880`06800000 fffff880`06879000 e1c62x64 T (no symbols)
Loaded symbol image file: e1c62x64.sys
Image path: \SystemRoot\system32\DRIVERS\e1c62x64.sys
Image name: e1c62x64.sys
Timestamp: Fri Aug 10 15:44:15 2012 (50258EBF)
CheckSum: 000829CE
ImageSize: 00079000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
You can try updating that,

https://downloadcenter.intel.com/Sea...net+Controller

There was also a mention about a Norton driver,


Code:
BugCheck 19, {20, fffffa800f5e2240, fffffa800f5e2360, 4120002}

Unable to load image \SystemRoot\system32\DRIVERS\e1c62x64.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for e1c62x64.sys
*** ERROR: Module load completed but symbols could not be loaded for e1c62x64.sys
Unable to load image \SystemRoot\system32\drivers\N360x64\1501000.012\SYMNETS.SYS, Win32 error 0n2
*** WARNING: Unable to verify timestamp for SYM... Read more

Read other 1 answers
RELEVANCY SCORE 68.4

Hi Experts, I have a serious problem using my W520 since a few month. When plugging in or unpluggingthe power cable the system directly jumps into Blue Screen (BSOD). I used a small tool to extract the basic dump message: RESOURCE_NOW_OWNED I installed the newest versions of LENOVO Solution Center, LENOVO Energy Management, ...I did an BIOS update longer ago, but I'm not sure, if there was a time-based relation to my problems. The BSOD occurs when: * Laptop started with power cable => Power unplugged* Laptop started without power cable => Power plugged* Laptop in sleep mode => Power plugged and Laptop started again lifting screen* Bring Laptop in sleep mode => Power plugged Does anybode had this problem. Before every meeting now I have to shutdown and restartthe engine... I'm not sure, if the Windows repair CD could detect and repair such a problem.Thanks in advanceKlaus Wegener

Read other answers
RELEVANCY SCORE 68.4

I went to start up my computer earlier and it would not boot up properly. Looking online someone mentioned it could be faulty memory. So one by one I took them out and started up the computer to see if it would boot with potentially removing a faulty memory stick. None of them seemed to be causing a problem so after installing all the memory back properly, neither of my monitors no longer receive a signal.
 
I have tried reconnecting everything and checking all connections. I have tried turning off the computer and extracting the CMOS battery for 30 seconds. Not sure what they next step in solving this is.

Read other answers
RELEVANCY SCORE 67.6

Event ID 11 (Warning) = Disk Controller
Device = SanDisk Cruzer, 8GB, Formatted FAT32
All USB Ports affected.

The device works perfectly.

Any ideas on how to eliminate the warning ?

A:Administrative Event ID 11 Shows After Plugging In USB Flash Drive

Try formatting it into NTFS. See this link....

Formatting flash drives NTFS and FAT32

Read other 2 answers
RELEVANCY SCORE 67.6

Just noticed this whenever I plug or unplug the charger. The laptop lags for 1-2 seconds before returning to normal. This is noticeable when playing games or watching videos. Haven't seen any abnormal drops or spikes with the temperature of the CPU, GPU and HDD which would suggest a hardware issue. Tried doing this while running 3DBenchmark, and there is a huge drop in FPS, from 130-200fps down to almost 16fps esp. when unplugging the charger.Is this normal?

Read other answers
RELEVANCY SCORE 58.4

Recently, my system started crashing and after diagnostic by Dell tech support, they found error in hard drive and replaced my drive. But even with new drive and clean installation, i am getting these errors and Dell tech support is no help.

It'll be highly appreciated if anyone could help.

A:Multiple BSODs even with new hard drive (Win 8.1)

Hello uday, from what it looks like to me, it seems like you're having a lot of driver issues. My advice is to update your drivers and make sure you get them directly from the manufacturer website. Especially your graphics driver.
Drivers | GeForce

If that doesn't help, start a thread in this thread: BSOD Crashes and Debugging - Windows 8 Forums

Read other 1 answers
RELEVANCY SCORE 58

Hello. For a couple months now my computer has been crashing multiple times a day, every day.

I ran a test through Dell PC Diagnostics on the Dell website and it told me there was a critical issue with my hard drive, so last week, I replaced it with a hard drive they recommended for my laptop. I reinstalled Windows 7 onto the hard drive because it didn't come with an OS, and as I was downloading and installing the drivers for my computer from the Dell site, my computer crashed with a BSOD. There was nothing else on my hard drive yet, so I have a feeling the issue is with one of the drivers from the Dell site? I don't really know. And since then, blue screen crashes have been a regular, every day thing, just as it was before replacing the hard drive, and now I'm wondering if my hard drive issue was unrelated to the crashing.

I'm not sure if this information would be any help but: I've ran other Dell PC Diagnostic tests on my other hardware and it's been saying everything is okay. For the test on software, they have a Blue Screen Analyzer, which I've ran and received two results: "Blue Screen Critical Error" and "Blue Screen Error". Then when I try to run the Blue Screen Troubleshooter, Dell System Detect (a program that the Dell site uses to connect to my computer, I supose) crashes and the troubleshooting never happens.

I don't have any of the error codes from the blue screens to give you because they seem to be different every time, and I never manag... Read more

A:Multiple BSODs a day before and after replacing hard drive

Code:
fffff880`031a14b8 fffff800`03132900 nt!PfSnBeginBootPhaseInternal
Free up the startup. Windows does not need any other program to auto start with it, but the auto start programs often conflicts and causes various problems including BSODs.
Click on the Start button
Type “msconfig (without quotes), click the resulting link. It will open the System Configuration window.
Select the “Startup” tab.
Deselect all items other than the antivirus.
Apply > OK
Accept then restart.
How many days ago you replaced the HDD?

The RAM/DIMMs need to tested, I think.

Code:
STACK_COMMAND: kb

CHKIMG_EXTENSION: !chkimg -lo 50 -d !nt
fffff80002ece9fb - nt!MiResolveDemandZeroFault+46b
[ ff:fd ]
1 error : !nt (fffff80002ece9fb)

MODULE_NAME: memory_corruption

IMAGE_NAME: memory_corruption

FOLLOWUP_NAME: memory_corruption

DEBUG_FLR_IMAGE_TIMESTAMP: 0

MEMORY_CORRUPTOR: ONE_BIT

FAILURE_BUCKET_ID: X64_MEMORY_CORRUPTION_ONE_BIT

BUCKET_ID: X64_MEMORY_CORRUPTION_ONE_BIT

Followup: memory_corruption
---------
Test your RAM modules for possible errors.
How to Test and Diagnose RAM Issues with Memtest86+
Run memtest for at least 8 passes, preferably overnight. Stop testing if it shows at least a single error.

First run it with all the existing/installed RAM modules. If it comes with no error, all is good.

But if it starts showing errors, Stop testing. Errors/red lines means one or more RAM is faulty. But the fault may occur due to a faulty DIM... Read more

Read other 7 answers
RELEVANCY SCORE 56

Windows XP will not access internet and will not back up data to any type of disc. Friend said to download glary utilities via my son's computer to flash drive and then run it on my computer. So I downloaded glary to flash drive. When I put the flash drive in my computer it shows these folders: autorun.inf (I clicked Install for this one but it gave error: Installation Failed), LaunchPad.zip (I clicked Extract All but it gave: Unable to Create the folder 'Launchpad'. Access Denied. Also tried clicking Open and it didn't respond at all), and Launchu3.exe (window asks me if I want to personalize it. I click "not sure" and it disappears). Thanks for any help you can offer!
 

Read other answers
RELEVANCY SCORE 56

Guys,

Can you insert two flash drives into the same computer? (As long as the USB ports are available?)

Jack
 

A:Multiple Flash Drive Question?

Yup. Ive got three 2 tb externals i synch weekly, all plugged into one rig. They are treated by the pc as just different drives and assigned different paths, e.g. d, e,f, etc.
 

Read other 1 answers
RELEVANCY SCORE 56

Please excuse my English.
 
I've soft-modded my Nintendo Wii and one Homebrew App can only read from FAT32 and another from NTFS. I want to have one flash drive that contains both partitions. I formatted my drive with both partitions using EASUS but EASUS won't let me give my second NTFS partition a drive letter. It gives an error:
 
"Windows only recognize the first primrary partition on a removable device. If no primary partitions, only the first logical partition is recognized."
 
I found this Lexar USB Format tool but I can't get it to work.
 
Chris

Read other answers
RELEVANCY SCORE 55.2

With the advent of EFI and the fact it boots from neat little files as opposed to however it was before in a technical sense, is it possible to put, for example, a Windows 7, Windows 8, and a Windows 10 installer all on the same flash drive and just choose at boot depending on what computer I happen to be fixing or building at the time? I've got this gigantic 128GB flash drive and this popped into my head...

Read other answers
RELEVANCY SCORE 55.2

Does anybody think it would be possible to put all versions of Windows XP, Vista, 7, 8 on 1 Flash drive if it was could somebody tell me how and how big the flash drive would have to be?

A:Multiple Copys of windows on 1 Flash drive?

Yes, I haven't them all, but most. I also have several Linux os and other isos. 32 gb is fine for me.

It would be a long explanation. Currently I start with windows boot manager, which can hand over to grub or isolinux.

Probably a better way (which i haven't got fully working yet ) is to use Ubuntu and Refind.

Read other 2 answers
RELEVANCY SCORE 55.2

Hello!

I recently used a 16GB USB flash drive to create an installer for a new Linux distro. I noticed that the created partition is 8GB and the rest 8GB is unused. I want to create a second NTFS partition so I can use the USB as a recording medium for my PVR, but Disk Management doesn't give me this option. I then used MiniTool Partition Wizard Home Edition, which did create the partition but warned that it won't be recognized by Windows as it normally sees only the first partition on a USB Flash drive. I even went back to Disk Management and assigned a drive letter to the second partition, but in Explorer I see only the EFI partition (first, drive is formatted in GPT mode) with that drive letter. Is there any workaround? Of course I could just format the whole drive as NTFS, but I wouldn't like to do so until I don't need the installer anymore.

A:Is it possible to create multiple partitions on a USB flash drive?

I was in a hurry and created the Recovery for Win10 on a 64GB Thumb drive but it automatically formatted only 32GB and put the data on it. Using Disk Management I could not create a second partition in the remaining space, all commands were grayed out. There was a warning Windows would delete all data and reformat. It did exactly that and formatted 32GB as FAT32. Windows has an issue with creating/formatting FAT32 partitions/drives above 32GB or rather anything about 1Byte smaller than 64GB unless doing it as NTFS. I booted to a GPARTED LiveCD and repartitioned the Thumb drive and formatted as FAT32. I've done the same for a USB Hard Disk Drive at 120GB formatted as FAT32 for use with my MacBook Pro OS X 10.x.x, now is at 10.10.5.

Read other 16 answers
RELEVANCY SCORE 54.4

I need some advice here. I have gotten blue screen errors sometimes when I plug flash drives into my computer. I would like to know where the error is coming from and exactly what is causing it. I have done some searches on it, but nothing solid has come up other than having a friend say its a virus. wanted a second oppinion to make sure.

A:Critical_Object_Termination error when plugging in flash drives

anyone?

Read other 9 answers
RELEVANCY SCORE 53.6

Thanks in advance for any advice.
The BDODs appear to be of multiple types.
Motherboard, RAM, wireless card and SSD were all replaced in early October and system completely reinstalled but BSODs continue. They are more likely to occur 1-2 min after waking from sleep, but recently also occurred when the system is just sitting.

System details below
Windows 7 professional SP1, x64
Version of OS: Windows(7), VOLUME_KMSCLIENT channel
See my profile for system details.

This is a laptop, Lenovo T440s

Darren

Read other answers
RELEVANCY SCORE 53.6

This is so odd. I'm running Windows XP SP2 on Dual core INtel with 1 gb memory.

I've installed a front USB panel that has 4 ports in front and 2 more on the PCI card which it's attached to. (added on peripheral).

I can deal with the "this device can run faster if plugged into a 2.0 device" but what is really frustrating is that if I plug in 2 or more USB devices. At least one of them won't work.

This computer is in my family room and wirelessy networked to my other computer in another room. I use a Motorola USB device to connect for the purpose of printing stuff off the printer in the other room.

If I have too many USB devices plugged in - there doesn't seem to be enough power to allow the wireless connection - resulting in not being able to print.

This isn't the only issue. I have some software that requires the USB "key" in order to work. If I need to use that software using the "key" and then I need to print something from that particular software to the remote printer - I have to save it to my desktop firsti - then disconnect the "key" and then I can print.

Do I need a bigger PS? I have a 500W now. I thought that would be big enough. Perhaps the USB issue isn't related to that at all? Is there some way to regulate how much power is assigned to USB devices?

Since my computer is in a desk against a wall - it's very difficult to plug and unplug stuff into the rear slots. Hence the install... Read more

A:Loss of power when plugging in multiple USB devices

Read other 16 answers
RELEVANCY SCORE 53.2

Integrate Multiple Antivirus Rescue Disk into One Single Disc or USB Flash Drive with SARDU ? Raymond.CC Blog

A:Integrate Multiple Antivirus Rescue Disk into One Single Disc or USB Flash Drive.

+1

I like it!

Read other 2 answers
RELEVANCY SCORE 52.4

Hi all, I've been having this weird problem and this site looked like a good place to ask about it because of the support I've seen. So wooooo first post~!
Anyway, whenever I unplug one certain flash drive (a Kingston DataTraveller SE9) my laptop bluescreens with the error "SYSTEM_THREAD_EXCEPTION_NOT_HANDLED". I can't figure out why for the life of me! I did, however, figure out that the flash drive is recognized as a local disk and not a removable one. This issue only applies to my laptop, that's it; the drive works perfectly fine on any other computer. I can still read and write to it no problem. Any help at all would be greatly appreciated!

A:Unplugging Certain USB Drive Causes BSOD

Some USB flash drives act like a hard drive which Windows lists as local disk instead of removable. You will notice that when you delete anything on the USB drive labeled local the deleted items go to the recycle bin. On a USB flash drive labeled removable the items are not sent to the recycle bin.
 
Download USBdeview. Run the program Highlight any listing for Kingston DataTravler and press the red X to remove. Reboot the computer and attach the Kingston again. Do you get the error?
 
http://www.nirsoft.net/utils/usb_devices_view.html

Read other 2 answers
RELEVANCY SCORE 51.6

I've been having BSOD trouble over the past four or five months now. The BSODs typically happen once a week, sometimes twice, with small strings of daily crashes here and there. I'm at my wit's end when it comes to trying to figure out where the problem lies. All of my parts are under warranty, so I'm desperate to find out which one, if any, are at fault.

I've tested my hardware extensively. Memtest86 for 7 passes on multiple occasions, using different stick and slot combinations. Ran torture tests using Prime95 for the processor. All hard drive checks come back without problems. Ran Furmark on my video card with no artifacts.

The BSODs happen most commonly when using video playlists for both Windows Media Player and Media Player Classic, multiple types of files. They also sometimes occur when playing particular games (Borderlands II, Dark Souls). Installing a fresh copy of Windows 7 did not remove BSODs, even after running it in factory settings with no additional installations.

I have attached a dump file, and I thank whoever attempts to assist me.

A:Multiple BSODs, Multiple Bugchecks (0xD1, 0x3B, 0x50, 0x0A)

Hi anthonylert.

The versatility of the bugchecks are the indication of failing memory prima facie, but as you said you ran Memtest86, can you run the memtest86+?

Test your RAM modules for possible errors.
How to Test and Diagnose RAM Issues with Memtest86+
Run memtest for at least 8 passes, preferably overnight.

If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there.

Also, disable bluetooth,at least as a test. The Atheros bluetooth module is appearing to be failing.

Free up the startup. Windows does not need any other program to auto start with it, but the auto start programs often conflicts and causes various problems including BSODs.
Click on the Start button
Type ?msconfig (without quotes), click the resulting link. It will open the System Configuration window.
Select the ?Startup? tab.
Deselect all items other than the antivirus.
Apply > OK
Accept then restart.
Let us know the results.

Read other 1 answers
RELEVANCY SCORE 51.6

Hey all. Sorry if this question has really obvious solution but I've been bashing my head against this for a few hours this afternoon and am getting nowhere.

I have downloaded the Win7 RC1 ISO and "burnt" it onto a 16GB OCZ Throttle eSATA / USB drive (exactly as in the SevenForums tutorial). I can boot from this drive and install Windows with no problem.

But... I believe the 200MB system partition is somehow being placed on the flash drive, because once I disconnect it and attempt to boot, I get the standard "DISK BOOT FAILURE..." message.

I've followed the suggestions on the "How to avoid 200MB hidden system partition" page (i.e., pre-create the desired partitions on the installation drive rather than installing to unallocated space), but I'm still getting the problem.

The "Windows might create additional partitions..." dialog box popped up once, on my first installation attempt - and I did foolishly click "OK" to it. It hasn't appeared since for me to click "Cancel" to, however much I try deleting and remaking partitions

Has anything changed in RC1 regarding the system partition? Is it more persistent in creating it than it was with the Beta? If anyone could give me some tips I would be very grateful indeed Thanks!

A:No boot after unplugging setup drive

The 100MB partition is for Repair purposes and should automatically be a part of the installation hard disk (even though it's an alltogether seperate partition).

You may want to check to see what disk the partition has been assigned to, run Computer Management from the start menu search box. See the screenshot and you'll notice that each disk is broken up into partitions (see highlight for Disk 0).

As for changing this option i'll look more closely into it for you

Read other 6 answers
RELEVANCY SCORE 51.6

I'm using Windows 7

Last night I was installing a new video card in my computer. The power supply was unplugged and I unplugged my E:/ drive so the I could have more room to move the video card around. When I booted my computer up it went to a black check disk screen which read similar to:

Checking file system on E:
The type of the file system is NTFS
Volume Label is New Volume.
One of your disks needs to be checked for consistency. You may cancel... etc

Chkdsk is verifying files stage 1 of 3

Then it listed each file and said the file is unreadable. such as 1 of 180000 is unreadable etc etc for each up to 184000 or w/e the number was.

After this I ran cmd and did chkdsk /r e:
Doing this was incredibly slow. I left the PC on overnight and when I woke up it was at stage 2/5, 10% completed and then stopped. Sorry I didn't screen shot the process but several times it said it was repairing corrupted files and at the end it said 'null' and then went back to the command prompt and nothing seemed to change.

Currently when I boot up my computer the E drive is sometimes visible and sometimes not under My Computer. It says 0 of 0 data stored and when clicking on the drive it says

E:/ is not accessible. The file or directory is corrupted and unreadable.

Previously Under Disk Management the Drive said that it had 0/0 GB storage but now it is showing the correct amount 0/932 GB. Well not entirely correct because I have about 30-50 gigs of games, pictures and v... Read more

A:E:/ Hard drive not recognized after unplugging it.

Read other 16 answers
RELEVANCY SCORE 51.6

Hey there,

So just to start things off, I'm 18 and don't really have much technical knowledge when it comes to computer hardware and errors, etc.

I started getting BSODs a while back, but they weren't very frequent, so I uninstalled all the programmes I had on my laptop and it stopped for the most part, so I assumed that was the problem.
As time went on up until now, they have been getting much more frequent, with the error message at the top stating something different each time, getting what seemed more serious. Sometimes when I get 1 BSOD, it would BSOD again on Startup, then again after that, which is rather frustrating haha.
I was reluctant to posting on forums, but it's come to the point of either fixing it logically, or ending up punching the screen xD

I can't really define when it happens, as it's more often some times than others, I have a hinch it has something to do with my graphics card though, as I would be playing a game, then I'd open up a new tab and watch a video then get BSOD at some point.
However it happens (less frequently for the most part) when idle or with minimum programmes running.

The programmes I mainly use on the laptop is:

Google Chrome
Skype
Sony Vegas Pro 11 (Video Editing Software)
Total Media Extreme (Personal Video Recording Software)

I can't remember any of the actual error codes, but some of the display messages i can remember are:

PAGE_FAULT_IN_NON_PAGE_AREA
Attempt to Execute to Non-Executable Memory
(som... Read more

A:Multiple BSODs, Random Occurences, Multiple Error Codes

Hello and welcome to Sevenforums.

Things we need
A nfo file




Quote:
To get this: Start Menu -> Type msinfo32 into the Search programs and files box -> When it opens, go to File, Save -> Save as msinfo32.nfo and save in a place you will remember -> Let it finish the process of gathering and saving the system info -> Right click the .nfo file, click send to compressed (zipped) folder -> Upload the .zip file here.



BSOD Analyse

Update these(this) driver

Code:
Afc.sys Wed Jul 12 07:48:20 2006 (44B48D24)
amdxata.sys Fri Mar 19 17:18:18 2010 (4BA3A3CA)
archlp.sys Fri Feb 6 13:39:29 2009 (498C2F81)
bcmwl664.sys Wed Jul 8 02:45:04 2009 (4A53EC10)
GEARAspiWDM.sys Mon May 18 14:17:04 2009 (4A1151C0)
hcwhdpvr.sys Wed Mar 7 16:03:30 2012 (4F5778C2)
igdkmd64.sys Fri Jun 3 22:34:06 2011 (4DE9453E)
intelppm.sys Tue Jul 14 01:19:25 2009 (4A5BC0FD)
MpFilter.sys Fri Mar 9 12:05:26 2012 (4F59E3F6)
yk62x64.sys Mon Sep 28 10:19:31 2009 (4AC07193)
http://www.carrona.org/drivers/driver.php?id=Afc.sys
http://www.carrona.org/drivers/driver.php?id=amdxata.sys
http://www.carrona.org/drivers/driver.php?id=archlp.sys
http://www.carrona.org/drivers/driver.php?id=bcmwl664.sys
http://www.carrona.org/drivers/driver.php?id=GEARAspiWDM.sys
http://www.carrona.org/drivers/driver.php?id=hcwhdpvr.sys
ht... Read more

Read other 8 answers