Over 1 million tech questions and answers.

I'm having a problem with the Karajan audio connector on my new DFI NF4 Ulta D mobo.

Q: I'm having a problem with the Karajan audio connector on my new DFI NF4 Ulta D mobo.

I'm having a problem with the Karajan audio connector on my new DFI NF4 Ultra D mobo.

I just finished putting together my new PC last night, and I've got Windows loaded and all of that good stuff.

But I'm having some audio problems.

My computer is not even recognizing any sort of audio output device.

The motherboard on-board sound piece is actually a separate piece that you connect to the board.

I have it connected well. I went back and made sure it was on good, and I installed the drivers and such, but I still can't seem to figure out what the problem is.

Karajan makes the audio piece, and I did a bit of Googling and I came across a guy on some other forum who was having the same problem, but he never mentioned how or even if he got it working.

Does anybody have any suggestions?

RELEVANCY SCORE 200
Preferred Solution: I'm having a problem with the Karajan audio connector on my new DFI NF4 Ulta D mobo.

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: I'm having a problem with the Karajan audio connector on my new DFI NF4 Ulta D mobo.

From here - http://www.nvnews.net/vbulletin/showthread.php?t=67098

"I had a similar problem (no sound output) and the way I fixed it was that I had the front case jumpers connected incorrectly and when I connected them correctly, it fixed the problem."

"I pulled them all off and swapped the front output from Line_Output_Front on the Karajan module to Line_Output and now everything works"

Read other 3 answers
RELEVANCY SCORE 59.2

Each time I turn on my computer, 10minutes later I get this popup message from Nvidia saying that my card isn't receiving enough power...
Help
 

A:Nvidia Geforce FX 5700 Ulta Problem

Read other 11 answers
RELEVANCY SCORE 56.4

My wife's computer - spec build: MoBo MSI A55M-P33 /N1996 / MS 7786 v.1.0. I found a MoBo description (on internet) which says it has a FDD connection. I think I've looked everywhere but haven't found it. Is it there or not?
Thanks.
 

Read other answers
RELEVANCY SCORE 56.4

How does one tell if their mobo has a 20 or 24 pin power connector (short of opening up the case and looking)?

EMachines T3508 Desktop

Intel Celeron D Processor 356 3.33GHz
533 MHz FSB | 512 KB L2 Cache
300 watt PSU
 

A:Mobo And PSU: Connector

You really just need to pop the side of the case off and look, unless you know the brand name and model number of your motherboard and can look it up on the manufacturer's website.
 

Read other 2 answers
RELEVANCY SCORE 55.6

Hi, I am tying to sort a PC for a friend. The PSU appears to be fried, so swapped that for a spare one. The spare provides power to the mobo in that the on board LED lights up, AGP powered fan spins up, as does the CPU fan and the case fan. However this is as far as I get, the is no video output. I am wondering if the mobo is fried too. One other thought is that the 20 pin connector on the original PSU contains 20 cables, whereas on newer PSUs there are only 19. Could it be that as the PC was built with a PSU which provided 20 cables into the 20 pin connector that a 20 pin connector fron a newer PSU which only contains 19 cables might not work? Sorry if this is a bit garbled.
 

A:Mobo power connector

partofthechaos said:





Hi, I am tying to sort a PC for a friend. The PSU appears to be fried, so swapped that for a spare one. The spare provides power to the mobo in that the on board LED lights up, AGP powered fan spins up, as does the CPU fan and the case fan. However this is as far as I get, the is no video output. I am wondering if the mobo is fried too. One other thought is that the 20 pin connector on the original PSU contains 20 cables, whereas on newer PSUs there are only 19. Could it be that as the PC was built with a PSU which provided 20 cables into the 20 pin connector that a 20 pin connector fron a newer PSU which only contains 19 cables might not work? Sorry if this is a bit garbled.Click to expand...

what mobo is it? does it have an additional 4 pin power connector? or an additional 8 pin power connector?

The more specs you can provide the better.
 

Read other 2 answers
RELEVANCY SCORE 55.6

Hello everyone! Happy New Year!!

I am trying to replace the standard 300 watt power supply in my HP m7350n computer. It looks like I can handle it, except I am worried about the 24 pin connector that attaches to the motherboard (P5LP-LE). I don't want to break anything, and it doesn't want to release when I press on it and try pulling. I am tempted to use a tiny screwdriver, but that feels like a bad move.

Any hints?

The new 430 watt supply has a 20 plus 4 connector. This just attaches like the 24 pin connector but in two parts (right?)

Thanks, Gordon
 

A:Release 24 pin ATX connector from mobo

Yes just break away the 4 extra pins, using anything you have
 

Read other 2 answers
RELEVANCY SCORE 55.6

hey all im really desperate with this. so i hope this doesnt be in wrong subforum.

well i recently cant get my computer booting. apparently because of the 4-pin mobo connector. im not sure whether its the mobo part loosen, or the power supply itself.

so after playing with the cables and such, my computer working. but its been twice from just now it freezes, (because of loosen 4-pin mobo).

so im confused, and worried, what to do in order to make the computer stable again? must i check the cable jack or....

regards
 

A:Mobo 4-pin connector going nuts

The 4-pin CPU power connector is supposed to snap in and lock... Did the locking lever break off, or is the whole connector loose?
 

Read other 2 answers
RELEVANCY SCORE 55.6

Title says it all pretty much, I'm getting my computer in about 30 or so days and my case has 3 fans on it and my motherboard only has one case fan connector, what can I do besides buying a more expensive motherboard?

Case: http://www.newegg.com/Product/Product.aspx?Item=N82E16811119197

Mobo: http://www.newegg.com/Product/Product.aspx?Item=N82E16813131647

Any help or advice is appreciated, this is my first build so I'm just trying to figure these things out lol.
 

A:3 fans 1 connector on mobo, what do i do?

The fans on that case look to have the 5 pin molex connectors . . you can use them instaead of the 3 pin motherboard connector
 

Read other 1 answers
RELEVANCY SCORE 55.6

Hi guys. I just received a PC a bought online. The motherboard is a "ASUS 1155 P8H61-M". The thing is that I ordered an extra fan apart with the one that comes with the case, and the thing is that this extra fan they gave me has a 3-pin female connector (see first image).
My motherboard only has 1 male 3-pin connector, and its reserved for the cpu fan. It also
has 1 male 4-pin connector but its occupied but the fan that comes with the case...
There is a weird series of 7 pin connectors in which my fan connector would fit, but I'm not sure if those are meant for fans 'cause to those 7-pin connectors my HDMI audio and USB connectors are connected....

My psu has no 3-pin male connectors, just more female 3-pin ones or some weird 4-big pin ones (see second pic).... what should I do?? Is there some kind of attachment I need to buy?

A:can't connect 3-pin fan connector to mobo

sorry not 7-pin connectors.. they have 9 pins

Read other 3 answers
RELEVANCY SCORE 55.6

I've got a Premio mobo. a 212J, that has an unusual board socket for the power supply.
It's a white plastic socket with the internal pins.(2 banks)
A scan of this board can be seen at:
http://home.earthlink.net/~gothix/premio.html

This is probably a real newbie question but I've never seen a power socket like it.
Thanx in advance.
 

A:mobo power connector???

Read other 6 answers
RELEVANCY SCORE 55.6

System Specs:
p4 3.0 prescott core
gigabyte socket 478 mobo
radeon 9800 pro (Sapphire)
dual 1gb rosewill mem. (2x512)
Compusa 500 watt power supply

Well let me start from the beginning. A few weeks ago my computer started to shut off while I was playing counterstrike 1.6. I checked my temps and they were well below the threshhold. Maybe about 65 C. So I figured it might have something to do with the graphics card being that i wasnt getting any problems outside of the game. I uninstalled the driver software and it gave me a couple errors. "Zero Display Service" error. I spoke with a friend and they told me to use nasty file remover, while booted in safe mode, to remove all the files. By this time I had cancelled windows "adding new hardware" thing, and clicked on the updated drivers I had downloaded from ATI. During setup i recieved two errors. One was an "INF Error : display driver not found" then "Setup could not complete, try installing thye standard VGA driver before beginning setup." Well the only other thing I could do was install using the disc that came with my card. This too gave me an the "Zero display Error" but it still completed the installation. This did not fix my computer shutting off problem. After cleaning out my computer and checking all the connections, and disconnecting and reconnecting I finally got the driver installation to not give me an error. I'm not sure how I did it, I used the cd, but for so... Read more

A:Melted 4 pin connector (mobo-ps)

Read other 9 answers
RELEVANCY SCORE 55.6

Im working wth a computer that lost its power supply. Specs are not needed, my question is very general. Helping troubleshoot via telephone.

Bestbuy brand power supply died. Owner replaced it with a Thermaltake PSU. The system shuts off after heavy usage like gaming and stuff.
Visual inspection shows that the 4 pin ATX connector socket on the mobo next to the CPU has some melted plastic inside it, so the new PSU connector doesnt fit snug.
If the connector is held down with tape, it will stay on longer, but eventually shuts off again.

I was wondering if I could clean the plastic off, or just get a 8" 4 pin extension cable, plug the female end into the new PSU, cut off the male end and solder it to the mobo.
I know that I will have to be careful and make sure nothing will short out. Just wondering if that would be a solid fix or not? Thats the only visible damage. Thanks in advance!
 

A:Burnt 4 pin 12v ATX connector on mobo

Only if you are experienced, and very good at soldering.
There should be a way of using that extension cable by slightly compressing the socket... and I do mean slightly, just to make the fit more firm.
If you have access to a womans power sander or file that many women use to repair and polish their nails, you might be able to clean up the posts in a way that would be helpful.
As you are aware, be very careful to avoid putting pressure on those posts because the motherboard is very fragile and any pressure offers the risk of damaging the contact between those posts and the board, and that will be extremely difficult to fix...

Be sure to use very good lighting and perhaps a magnifying glass to be sure it is not already damaged.
 

Read other 5 answers
RELEVANCY SCORE 55.6

I bought a Startech hot swap tray for my 5.25 bay and it installed with no problem,but I have a 2pin connector for the LED and I do not know where to plug it in at. Also do I need to plug it in? I have a EVGA 680iLT mobo if that helps. I do not see anything in the mannua.l

A:Plug 2 pin connector on MoBo

Can you provide a picture of the 2pin plug. It would help greatly.

Read other 9 answers
RELEVANCY SCORE 55.6

Hi!

I have a MSI Z170A Mobo. It comes with an on board RGB connector. I currently have two RGB Fans connected and working properly.

My question is how many more can it handle. I want to expand to 6 fans all RGB connected in series
 

Read other answers
RELEVANCY SCORE 55.2

I've wanted to know the difference in useing ATX power connector and ATX 12V connector. my mobo and psu both support ATX and ATX 12V. standard atx i kow has been around for awhile. so what the difference?
 

A:Solved: Mobo Power connector

1.2. Key Changes for ATX12V Version 2.0 and later as Compared with ATX and Pervious Versions of ATX12V Power Supply

This section briefly summarizes the major changes made to this document that now defines ATX12V power supply. With the move to 12V voltage regulators for the processor, ATX guidelines for 5V as main power are no longer provided.

1.2.1. Increased +12 VDC output capability
System components that use 12V are continuing to increase in power. In cases where expected current requirements is greater than 18A a second 12 V rail should be made available. ATX12V power supplies should be designed to accommodate these increased +12 VDC currents.

1.2.2. Minimum Efficiency
Minimum measured efficiency is required to be 70% at full and typical (~50%) load and 60% at light (~20%) load. New recommended guidance has been added to provide direction for future requirements.

2.03 is the current version of the ATX Specification as of this writing. Future references to the ATX Specification in this document imply version 2.03 or later, as applicable. ATX12V Power Supply Design Guide 8

1.2.3. Main Power Connector:
The 2 x 10 main power connector has been replaced by a 2 x 12 connector. This was made to support 75 watt PCI Express*requirements. Pinout assignments are based on the SSI recommendation.

With the added 12V, 5V, and 3.3V pins the need for an Aux Power connector is no longer needed and the guidance for this connector has been removed.

1.2.4. Separate current limit for... Read more

Read other 3 answers
RELEVANCY SCORE 55.2

I have a hiper modular psu, and the asus A8N-Sli premium mobo, in the antec p180 case, for anyone who has a similar set up (or has just used that case in fact) has probably noticed getting the 12v 4 pin atx connector from the psu (in bottom left hand corner) to the ATX slot (in my case the top left hand corner), is kindof hard unless you have a rather long cable (espesically as with the case layout you have to slide it through pretty much the middle of the case). Anyway this wasnt really a problem for me until I bought a new sound card and the fact that the cable is tought across all my spare pci slots is suddenly rather annoying, basically I either need to extend the original cable, convert a molex into the 4pin 12v ATx cable, or buy a whole new cable thats a bit longer (as the PSU's modular). Feedback on how to do either of these (or which is best) would be greatly appreciated (even just a website to buy the parts from would be great as I can't find one anywere) as having a soundcard sitting on my desk is rather annoying, to think i could be fragging in surround sound
 

A:4 Pin 12V atx connector to mobo isnt long enough

I'd go with an extenstion since all you need is a little more slack.

Found one at this UK site Maplin.co.uk
I don't know where you're posting from, but there's likely to be a retailer that has a similar item near you.

EDIT: Doh, just noticed they're out of stock.
Lots of extentions here: performance-pcs.com
 

Read other 3 answers
RELEVANCY SCORE 55.2

Hi, i have a http://www.fic.com.tw/product/motherboard/INTEL/VG33.aspx and i dont know where the case connector plugs go (power on, h.d.d led, speakers) I dont have any manuals or cd's, just the mobo.
 

A:Need to know where case connector plugs go on new mobo.

Go HERE and download the manual.

Regards Howard
 

Read other 1 answers
RELEVANCY SCORE 55.2

Okay I've searched up and down the web and can't find anything about this connector.

First off this is a 300-watt Compaq PSU from a Presario 7000 Desktop.

This Compaq computer won't power up. When I installed a standard ATX-12 PSU, the green light on the mobo came on but because most ATX-12 PSU's don't come with this very proprietary connector the computer failed to boot up. The CPU fan didn't even twitch. But the mobo green light AND the PWR LED on the front of the case lit up. Neither lights came on with the original Compaq PSU.

This connector is white and labeled "P8" and is a 6-conductor white plug. The overall size is similar to the power connectors you plug into your hard drive and other IDE devices. It looks like an oversized floppy drive connector. The wiring colors are: Red, Orange, Orange, Black, Black, Black.

I've traced the wires and here's where they go to the PSU's circuit board:

Red - connects to the same red lead on the IDE power connectors
Orange - connects to the same orange leads on the main power (mobo) connector
Black - connects to what looks like the PSU's chassis ground.

It looks pretty straight forward and I could probably modify a standard ATX-12 PSU to a Compaq PSU by snipping off this 6-conductor plug and splicing into a generic PSU's standard wiring.

But before I attempt this, is there anyone out there that knows the pin configuration on a standard/g... Read more

A:Compaq PSU 6-pin connector plugs onto Mobo near IDE

This link may be of some use to you possibly.
http://www.technick.net/public/code/pinouts.php

If not, i have opened up and rewired many psu's.

Rik.
 

Read other 4 answers
RELEVANCY SCORE 55.2

My motherboard is a model Ms-6330 Ver: 2.1 (Microstar) but it also has the gateway part number 2512595. I am currently relocating this motherboard to a brand new case that I just bought and I ran into a problem. The front panel connectors (power switch, led, hdd led, etc) go onto the motherboard in a certain area where there are 15 pins. Unfortunately I have no idea which connectors connect to which pins. Can someone help me? (Maybe someone with the same motherboard/problem). All I need is a way to identify the pins and make sure I don't like accidently fry my motherboard. Thanks a lot! -Andrew C.
 

A:Front Panel Connector on Mobo

Hi,
For starters, have you checked your manual? Also, look on the m/b...in really tiny abbreviated letters you should be able to see where these go (you may see "pw switch"...."HDD ACT"........i know when i was installing my connectors, i got most of them wrong..but dont worry..no frying of the motherboard.....if the connector is in the right place but no light from the LED..try reversing the cable........the easiest cables to place are the pw switch and the reset..as you can test these easily....good luck
 

Read other 3 answers
RELEVANCY SCORE 55.2

I have a connector on my mobo for USB 2.0, It lists 2 pairs of pins like
5V, 7-, 7+, GND and 5V, 8-, 8+, GND

Then it shows a single pin at the end of the connector labeled NC.

One my USB from panel connector I have 2 sockets matching the 2 pair of pins on the mobo USB connector. Then there is a single wire in the same bundle from the fron panel USB socket with the 2 connectors that is labeled GND. Does the single wire from teh front panel socket that is labeled GNDgo on the mobo pin labled NC?

Thanks,
Charles
 

A:Pinout label on USB mobo connector

I believe that the label NC stands for No Connection.
 

Read other 3 answers
RELEVANCY SCORE 54.4

Hi, I researched this board and found two other posts documenting this issue:https://forums.lenovo.com/t5/ThinkPad-P-and-W-Series-Mobile/P51s-sata-ribbon-attachment-FAIL-NO-FIX/...https://forums.lenovo.com/t5/ThinkPad-P-and-W-Series-Mobile/P51s-sata-HDD-cable-FRU-dislodged/m-p/40... Interestingly enough, this seems to be a problem to at least two other people during the month of March 2018. I have this same problem. My p51s just all of a sudden stopped detecting the storage drive. I opened the case to find that the SATA connector wasn't even connected to the motherboard. The connector that should hold the sata cable is just completely detached. And the piece that was within that connector is out of place as well. Please reference this photo (NOT MY PHOTO -- not taken by me, credit:https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/Upgrade-ThinkPad-T570-from-SATA-HDD-to-M...):  This person's laptop seems to have a strong solder, which I don't believe mine did. Please advise how I can get this repaired, get a new computer, or just give me my money back. I've used Lenovo for ~10 years and have never had problems like this. I need this computer to work.

A:p51s sata mobo connector is broken

+ picture of connector parts, detached

Read other 2 answers
RELEVANCY SCORE 54.4

does anyone know or have a good reliable psu (550w or so) with a native 24pin mobo connector. im gonna get this dfi lan party mobo and its highly recommended to have a 24pin and not a 20 with an adapter so ive been looking around but all i can find are the adapter ones and really expensive ones. im looking to drop at most $150. much thanks as always.

also needs to be pcie compatible and sli and sata and other goodies

planning on putting in a evga 7800gtx KO if newegg ever gets it back in stock.
 

A:good psu with a native 24pin mobo connector

Newegg list of SLI PSU's
 

Read other 5 answers
RELEVANCY SCORE 54.4

Hi everyone. Ive just finished plugging my power led, hdd led and pc speaker into my motherboard. The only thing i have to plug in now is the reset switch but i dont know where it goes. Does anyone know where it plugs into? My motherboard is a DCS 370VB.
 

A:Cant find reset switch connector on mobo.

It shows up nowhere in the manual ? Generally it is quite close to the set of pins to which you plug the HDD led, speaker, etc.

ps. searching for your motherboard on Google doesn't yield much results so I can't seem to find a digital manual for it.
 

Read other 1 answers
RELEVANCY SCORE 53.6

I built this rig about 3 months ago, and was using windows XP with no problem. I needed a new HD because mine crashed, and I lost my copy of XP. I decided to just use my older copy of windows 98SE because all I was using the system for was playing Dvds, music etc.

Anyway, all other drivers installed without a hitch. When I got to the final driver to install, the C-Media sound driver, it said it could not find any system files. After a few attempts, I finally found the lost folder on the CD containing the "system files" needed, and it installed.

.. Still no audio. Anyway, after the installation it asked me to reboot. When I reboot and attempt to play a sound file, windows says there is no sound device installed, when CLEARLY there is one installed, and shows in the device manager. Device manager also says this hardware is working properly, and displys the correct driver.

This is totaly fusturating!

Dave
 

A:Problem with audio on SOYO dragon2 v1 Mobo. HELP!

Read other 10 answers
RELEVANCY SCORE 50

Having upgraded my T7500 to Windows 10 the on-board audio interface no longer works.
I have installed a Soundblaster Audigy FX sound card which is working fine.
What I would like to do is to connect the sound card to the front panel headphone and microphone socket.
At the back of the motherboard (close to the I/O panel is a 10 pin connector labelled FP_Audio. On the sound card is a 10 pin header, which, according to the manual is for connecting to a front panel audio connector. It goes on to state that it is "Intel HD Front Panel Audio standard only. Not compatible with AC97 or Intel-compatible HD Front Panel Audio". The pin connections, according to the Soundblaster manual are:
1 - Analog port 1 Left Channel (microphone)
2 - Ground
3 - Analog port 1 Right Channel (microphone)
4 - Presence# (Active low signal that signals BIOS that an Intel HD Audio dongle is connected to theanalog header. PRESENCE# = 0 when an Intel HD Audio dongle is connected.)
5 Analog port 2 Right channel (headphone)
6 - Sense 1 Return
7 Sense Send (Jack detection sense line from the Intel HD Audio CODEC jack detection resistor network)
8 Key
9 Analog port 2 Left Channel (headphone)
2 Sense 2 Return
Is the T7500 FP_Audio connector compatible with this? If not could someone please provide me with the pin connections to the FP_Audio connector so that I can make up a custom lead to go between the soundblaster board and the front panel.
Thank you

Read other answers
RELEVANCY SCORE 50

Hello
I have attached an image of my cabinet, i have front usb & two covered hole (selected with red line in the image) besides it. I think they are front audio but it has no wire from inside. please have a look at it & let me know if i can make it a front audio connector.
thanx
 

A:Front audio connector

Read other 16 answers
RELEVANCY SCORE 49.2

I have a self-assembled desktop PC - full specs in the signature below, but in short, it has an AMD Phenom II X6 1090T processor on a Gigabyte GA-970A-DS3P mainboard, which uses a Realtek Azalia ALC887 on-board sound system. I have no loudspeakers and listen to the computer sound exclusively through a Microsoft LX-1000 headset. I also have a Logitech C270 HD webcam that has its own microphone. My PC has 16 GB RAM, a SSD and a large HDD. It runs Windows 8.1 Update 1 with all Windows updates (Patch Tuesday was this week, but my problems had started before that and I'm sure they're unrelated).

Everything is working fine, except the audio, which started behaving strangely a few days ago. The problems started suddenly and I can't think of anything that could have caused them. There were no hardware changes or any intervention in the hardware, nor did I install any new software that could have messed up things.

When playing music, it sounds muffled, with the volume very low and the voice and several instruments muted, while other instruments in the background arrangement sound louder. No graphic equalizer is on, and this happens with any player software (Windows Media Player, VLC, Media Player Classic, etc.), and any source (MP3 music, audio CDs, DVDs, videos, etc.). There appears to be no hardware problem with either my headset or the onboard audio: when I run both Windows' native and Realtek's driver sound output tests, the test tune comes out loud and clear in the tested chann... Read more

A:Realtek audio, Gigabyte mobo: strange-sounding audio, mic not working

First thing to do is disable or disconnect the Web Cam. They have been known to cause various sound problems. It may not be the problem, but eliminate it as the problem.

Stereo Mix needs to be set as the Default Recording Device.

Refresh the RealTek by going to the Device Manager, RIGHT click on the RealTek entry in the Sound section then LEFT click "Uninstall". DO NOT uninstall the drivers. Restart the PC and when Windows starts it will reinstall the sound. This usually fixes any Windows/Sound corruptions. If this does not fix it, download and reinstall the RealTek sound drivers.

Read other 1 answers
RELEVANCY SCORE 48.8

I have a self-assembled desktop PC - full specs in the signature below, but in short, it has an AMD Phenom II X6 1090T processor on a Gigabyte GA-970A-DS3P mainboard, which uses a Realtek Azalia ALC887 on-board sound system. I have no loudspeakers and listen to the computer sounds exclusively through a Microsoft LX-1000 headset. I also have a Logitech C270 HD webcam that has its own microphone. My PC has 16 GB RAM, a SSD and a large HDD. It runs Windows 8.1 Update 1 with all Windows updates (Patch Tuesday was this week, but my problems had started before that and I'm sure they're unrelated).

Everything is working fine, except the audio, which started behaving strangely a few days ago for no apparent reason. The problems started suddenly and I can't think of anything that could have caused them. There were no hardware changes or any intervention in the hardware, nor did I install any new software that could have messed up things.

When playing music, it sounds muffled, with the volume very low and the voice and several instruments muted, while other instruments in the background arrangement sound relatively louder. No graphic equalizer is on, and this happens with any player software (Windows Media Player, VLC, Media Player Classic, etc.), and any source (MP3 music, audio CDs, DVDs, videos, etc.). There appears to be no hardware problem with either my headset or the onboard audio: when I run both Windows' native and Realtek's driver sound output tests, the test tune comes out... Read more

A:Realtek audio, Gigabyte mobo: muffled audio, no mic input

This is a duplicate of what is posted on the Seven Forums.

Read other 2 answers
RELEVANCY SCORE 48.8

Hi everyoneWhile I took the front panel off of my case the other day I accidently removed the JAUD1 jumpers....and now my sound doesn't work. I downloaded the specific instruction guide from MSI for my motherboard and here's the section for it:The two right sound in and out cables were still attached, and I got sound out of my right speaker. But then when I connected the rest to what I thought was correct, I got sound out of my left speaker only. EDIT: I tried not attaching any of the cables and then I get no sound.The problem I have with these directions is that the cables are not labeled the same as the diagram. They are as follows:Purple - R INYellow - R OUTBlack - GNDGreen - MIC BIASBlue - L INRed - L OUTBlack - GNDOrange - MIC INCan anyone help with this? I'd love to have both of my speakers playing sound again....

Read other answers
RELEVANCY SCORE 48.8

So I basically have a very odd front panel audio connector setup, very confusing, I've made over 10 thread on different forums and non were able to help me.

I'm using a Gigabyte G31 motherboard GIGABYTE - Motherboard - Socket 775 - GA-G31M-ES2L (rev. 1.x)

Manual page for the motherboard output can be found below the first image

The front panel audio connectors consists of:
Yellow- MIC BIAS
Green - SPKOUT R
Peach - MIC In
Blue - Return L
Black - Ground
White - SPKOUT L
Grey - SPKOUT L

Much Thanks and appreciation to those who read this read

A:Front Panel Audio connector help needed

Your front panel connections aren't odd, but they are old. They are for the AC97 standard.

Set your onbaord audio to AC97 in the BIOS set-up.

The AC97 pinouts are here:

Desktop Boards — Front panel audio header pinouts

1 Mic In
2 Ground
3 Mic Bias
5 Spkout R
9 Spkout L

It looks like the onboard audio doesn't support the Return lines.

There should only be one Spkout L connector. It's the white (not gray) one.

Have you really been trying to figure this out for 5 months? Yikes.

If these connections cause your PC to go up in a fireball, don't blame me.

Read other 1 answers
RELEVANCY SCORE 48.8

Hi
I recently bought a PCTV Plus (India Version).I wanted to connect the audio through the Internal Connector provided to free the Line In Port.But the online documentation which came with the product is of the PCTV Pro.The PCTV Pro has Vertical Internal audio connector the PCTV Plus has Horizontal audio connector.As the pinout given is of the PCTV Pro I don't know the PCTV Plus's pinout.What is the pinout?
 

A:Internal audio connector in Pinnacle PCTV

Should be a four pin connector, left/ground/ground/right.
 

Read other 2 answers
RELEVANCY SCORE 48.8

Hi, I'm new to the Vista forum, but I've searched for a similar problem in other threads to no avail, so here goes, I recently bought an MSI K9A2GM-FIH AMD 780G AM2+ Motherboard and am running Vista Home Premium 32bit os, I need to find a suitable rear panel connector to take the HiDef Audio from the on-board header to my AV amp. There was nothing supplied in the box and the reseller is less than helpful, any ideas where I can get an back panel connector/adapter to give me either co-ax or optical audio out from the MB?

Cheers

AndyGz

A:Rear panel HD Audio connector required

Hi Andy and welcome to the forums

I presume that this is what you mean. Have a look at the following link. Please note that there is a time limit, so you will have to be quick.



MSI Motherboard S/PDIF Digital Coa Audio Out cable - eBay (item 230290271471 end time Sep-18-08 05:13:29 PDT)

Here are some more links.

http://www.yoyotech.co.uk/product_in...31&cPath=62_64
http://www.cclonline.com/product-inf...ufacturer_id=0

Read other 4 answers
RELEVANCY SCORE 48.4

Hi,

Not sure if this is possible, but thought I'd toss it out there... I'd like to have audio sent via HDMI to my monitor while at the same time using the MoBo output jack for a subwoofer. I've only been successful with one or the other by itself in any configuration I've been able configure.

Any thoughts?

Thanks

A:HDMI Audio AND Realtek MoBo Audio Simultaneously

Does your monitor have an Audio Out? Some do. If it does, HDMI to the monitor, then audio out from the monitor to your subwoofer. Mind you plugging something into the audio out may turn off the monitors internal speakers. You won't know until you try
But…here’s the kicker! A subwoofers job is to not only produce lower frequencies but to also blend nicely into its satellites (speakers). This is most commonly accomplished by either designing the sub and satellites to work together in that the lower cut off frequency of the satellites is close to the higher cut off frequency of the subwoofer. The other is to have an adjustable crossover that will allow you to match the subwoofers higher cut off frequency to that of the satellites lower cut off frequency. You also need to match their output (sound) so that they are even (or close enough!). Otherwise you will get a lot of boom from the sub and not be able to hear much from the monitor.
Monitors with built in speakers are not designed with fidelity in mind. They have tiny amplifiers and do not go very loud without sounding terribly distorted. Even if your monitor does have an audio out, you may be presented with the impossible challenge in trying to match it to your subwoofer. Honestly, you are better off purchasing a 2.1 (or 5.1) computer speaker system. You can get something pretty decent for not too much money.

Read other 3 answers
RELEVANCY SCORE 48.4

hi i just got a new computer built for gaming i got a used but perfect gaming card which is ndvia geforce fx 2500 ulta sometimes when i start my computer i ether goes to black screen or a blue screen of death ive tried the power thing did not help ive tried to reinstall windows did not help
my uncle did it but i forgot how he did it so please reply and help
 

A:ndvia geforce fx 2500 ulta help

Read other 6 answers
RELEVANCY SCORE 48.4

Hi, I have got the Lenovo d367 h81 for a long time, or rather the entire system Lenovo 530 (for nothing, so to speak), today I decided to install a normal case (Deepcool smarter).USB and f_panel (hdd led, power led, reset sw, power sw) work fine, but I just can't connect the audio connectors ... But having the original 14 pin connector. Already found a topic where everything was painted in detail, nothing fits... And especially with a ledge it introduces a gray contact, which is not... Colors are: black (going to the panel), black (as a jumper from the first), white, yellow, green, red, blue, brown and purple. Sorry for english from google '

Read other answers
RELEVANCY SCORE 48.4

Looking at the HMM for my 20KH I am trying to understand what the 'Proximity sensor connector' (p.54 in HMM) is for? It appears to connect the WLAN to the audio card? Why is this?  I am trying to work out if this is the cause of some interference I am experiencing when using the audio jack on this laptop.

Read other answers
RELEVANCY SCORE 48

We have a client of ours that has a T560 and a Lenovo Ultra Dock.  The problem is that when the laptop is on the Ultra Dock the laptop will enter sleep mode in about a minute or maybe 2.  I have all the settings to a minimum of 10 minutes everywhere and if it's not on the dock it works fine.  Both the on battery and on ac power options are set the same.  Have tried different configurations to no avail.  I have tried several online fixes that I could find for power/sleep issues with Lenovo laptops but none of which have fixed it.  Windows power settings and Lenovo power settings are set the same.  I have no idea where the laptop is even getting the idea to go to sleep at the 1 minute mark. Am I missing something here or what could it be?

Read other answers
RELEVANCY SCORE 48

Hello,

I wonder if any of you can help me, I've just got a new computer. First things first, it booted up and windows vista seemed to be slow and sluggish, if you want the full spec of my comp check out my specs.

I ran an update to my soundcard software and it reset halfway through the update. It then reset about 3 times and on the fourth it wouldn't boot at all. It would power up , but i'd get no picture or signal on my monitor, not even at the bios check stage.

I opened up my comp and ensure allthe connections were in plugged in correctly, I noticed on my mobo that it was showing a code 20. I couldn't find any info on this, so I'm not sure what this means.

If there's anything else you wanna know, just ask me. Any help will be greatly appreciated. Thanks in advance
 

A:Solved: Nforce 790i Ulta Motherboard

I meant Nforce 790i ULTRA sli Motherboard
 

Read other 2 answers
RELEVANCY SCORE 48

I have a HP Split X2 Model 13-m110dx.  I replaced the LCD/Digitizer assembly, which required I remove all hardware from the display assembly.  My question focuses on the cable that connects the motherboard to the audio/HDMI/Dock board (item 7 on page 17 of http://www.hp.com/ctg/Manual/c03958968.pdf).  The cable of interest is the left one (with a 45 degree bend in it), and how it connects at either end.  A pic is below with the cable (yellow/gold). My question:  Is this a ZIF connector or do I need to lift up the front to release it?  A portion of the gray part of the connector broke off when I tried to lift it, assuming it was a clamp style ribbon cable connector.  The other end of the cable connects to the Motherboard with the same type connector.  I pulled that one out, but it's unclear if that is damaged if I did that wrong. Problem:  The HP Upgrade/Parts manual doesn't define how to disconnect these cables.  After reassembly, the keyboard/dock no longer connects, so what I have now is a standalone tablet w/o any USB ports or keyboard.  I ordered a new audio board in the hopes that resolves the issue. Anyone have any input on this? 

Read other answers
RELEVANCY SCORE 48

HiI am trying to determine which type of 3.5mm audio plug to put into the front panel connector for using headphone with a microphone to do video communications. could be - sleeve, ring and tip (mono sound and microphone)orcould be - sleeve, ring, ring, and tip (stereo sound and microphone) Have read through the manuals and nothing is said about which type to use.

A:Front panel audio connector - what plug type to use for head...

Hi, I can't see your image but probably you can see mine   (a) All standard 3.5mm (stereo) headphones will fit and work.(b) For the second port on the right, all standard 3.5mm headsets will fit and work. Its default is for microphone, all standard 3.5mm mono microphones will fit and work. Note: probably around 95% of 3.5mm headphones and microphones on the market now are normal/standard. Regards.

Read other 1 answers
RELEVANCY SCORE 48

I found a lot of people searching for this information... since I was unable to find it, I tested the front panel connectors by myself, and that is what I found:
 
Power front panel (black connector)
 
+----+----+----+----+----+----+----+
| Bk | | | | | | |
+----+----+----+----+----+----+----+
| Yl | | Bk | Gn | Yl | Bk |xxxx|
+----+----+----+----+----+----+----+

+----+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 | 13 |
+----+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 | 12 |xxxx|
+----+----+----+----+----+----+----+

Description

1 Black Disk activiry led ground
2 Yellow Disk activiry led ground
3 Not connected
4 Not connected
5 Not connected
6 Black Power led ground
7 Not connected
8 Yellow Power led signal
9 Not connected
10 Yellow Power switch signal
11 Not connected
12 Black Power switch ground
13 Not connected
14 Locked (no pin)
USB front panel (yellow connector)
 
It's a standard internal USB connector, but with two additional ground wires
 
+----+----+----+----+----+----+
| Bk | Re | Wh | Gn | Bk | |
+----+----+----+----+----+----+
| Bk | Bw | Bl | Yl | Bk |XXXX|
+----+----+----+----+----+----+

+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 |
+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 |XXXX|
+----+----+----+----+----+----+

1 Black Ground
2 Black Ground
3 Red US... Read more

A:ThinkCentre front panel connector (power, audio and USB) pinouts (A60, M58, M71, M91, M92)

OK I am intrigued.  What are you trying to accomplish ... a hibrid A60 ?





T23: 2647-8RU, Ubuntu 12.04 LTSA61E: 6418-12U, W7/Pro 64X200: 7454-CTO, W7/Pro 32

Read other 9 answers
RELEVANCY SCORE 47.6

I found a lot of people searching for this information... since I was unable to find it, I tested the front panel connectors by myself, and that is what I found:
 
Power front panel (black connector)
 
+----+----+----+----+----+----+----+
| Bk | | | | | | |
+----+----+----+----+----+----+----+
| Yl | | Bk | Gn | Yl | Bk |xxxx|
+----+----+----+----+----+----+----+

+----+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 | 13 |
+----+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 | 12 |xxxx|
+----+----+----+----+----+----+----+

Description

1 Black Disk activiry led ground
2 Yellow Disk activiry led ground
3 Not connected
4 Not connected
5 Not connected
6 Black Power led ground
7 Not connected
8 Yellow Power led signal
9 Not connected
10 Yellow Power switch signal
11 Not connected
12 Black Power switch ground
13 Not connected
14 Locked (no pin)
USB front panel (yellow connector)
 
It's a standard internal USB connector, but with two additional ground wires
 
+----+----+----+----+----+----+
| Bk | Re | Wh | Gn | Bk | |
+----+----+----+----+----+----+
| Bk | Bw | Bl | Yl | Bk |XXXX|
+----+----+----+----+----+----+

+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 |
+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 |XXXX|
+----+----+----+----+----+----+

1 Black Ground
2 Black Ground
3 Red US... Read more

A:ThinkCentre front panel connector (power, audio & USB) pinouts (A55, M58, M71e, M73, M91, M92, M93)

OK I am intrigued.  What are you trying to accomplish ... a hibrid A60 ?





T23: 2647-8RU, Ubuntu 12.04 LTSA61E: 6418-12U, W7/Pro 64X200: 7454-CTO, W7/Pro 32

Read other 9 answers
RELEVANCY SCORE 47.6

This of course will not hurt your weight loss advances. just as long as you possess a cheat MEAL (or snack). and not much of a cheat Big day!Going on the gym is really a good idea, but many dieters acquire a weight loss gym membership and then never that. Ultavive Garcinia The idea of going to your gym onrr a daily basis and exercising for a workout or more is just too intimidating, and that they can't find the time.Add plenty of fiber with the diet. Fiber is heavier and stays longer stomach, which has the effect of supporting better the digestion rate. Fiber also moves fat while using digestive system a large amount faster.Those with diabetes symptoms related to very bloodstream pressure sugar often feel a sense of illness, weight-loss and vomiting. They can also feel dizzy or light-headed. When these symptoms occur, the blood sugar is often greater than 300 mg per deciliter but can be as high as 600 milligrams per deciliter. Blood sugars above 600 milligrams per deciliter can cause an altered sense of consciousness and a noticeably diabetic coma.
Visit Here For ZA : http://www.garciniasstore.com/ultavive-garcinia/

http://www.garciniasstore.com/garcinia-slim-fit-180/
 

Read other answers
RELEVANCY SCORE 46.8

I found a lot of people searching for this information... since I was unable to find it, I tested the front panel connectors by myself, and that is what I found:
 
Power front panel (black connector)
 
+----+----+----+----+----+----+----+
| Bk | | | | | | |
+----+----+----+----+----+----+----+
| Yl | | Bk | Gn | Yl | Bk |xxxx|
+----+----+----+----+----+----+----+

+----+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 | 13 |
+----+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 | 12 |xxxx|
+----+----+----+----+----+----+----+

Description

1 Black Disk activiry led ground
2 Yellow Disk activiry led ground
3 Not connected
4 Not connected
5 Not connected
6 Black Power led ground
7 Not connected
8 Yellow Power led signal
9 Not connected
10 Yellow Power switch signal
11 Not connected
12 Black Power switch ground
13 Not connected
14 Locked (no pin)
USB front panel (yellow connector)
 
It's a standard internal USB connector, but with two additional ground wires
 
+----+----+----+----+----+----+
| Bk | Re | Wh | Gn | Bk | |
+----+----+----+----+----+----+
| Bk | Bw | Bl | Yl | Bk |XXXX|
+----+----+----+----+----+----+

+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 |
+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 |XXXX|
+----+----+----+----+----+----+

1 Black Ground
2 Black Ground
3 Red US... Read more

A:ThinkCentre front panel connector (power, audio & USB) pinout recase (M58, M71e, M73, M91, M92, M93)

OK I am intrigued.  What are you trying to accomplish ... a hibrid A60 ?





T23: 2647-8RU, Ubuntu 12.04 LTSA61E: 6418-12U, W7/Pro 64X200: 7454-CTO, W7/Pro 32

Read other 9 answers
RELEVANCY SCORE 46.8

This is a minor issue but I have a external lite on that came with a nero 6. Recently I upgraded to nero 7 ultra. Now when I playback my burned dvd to my dvd player I notice that when I fast forward at anything more 2x the speed the dvd freezes then returns to the original menu. I never had this issue when I used my nero 6. I use to be able to fast forwarda burned dvd at 8x the speed, the maximum of my dvd player.
Except for this everything else seems to work fine. I tried changing the speed in the nero vision 4 just before burning. First I made sure that the write settings were on max. When that didn't work I tried setting the write speed to 8x. Still no change. Is this some glitch with nero 7 ultra or has my setting been some how changed when I upgraded?
 

A:Problems fast forwarding burned nero 7 ulta dvds

Are you still using the same media? Try changing to a different make of blank media and don't always assume that setting the write speed to max is a good idea!
 

Read other 1 answers
RELEVANCY SCORE 43.2

hi all
just a quickie, not realy a problem just not quite sure lol.
i have just bought a new surround sound setup with 3 leads to conect 2 pc.
am i reading this right? the 3 inputs on my mobo are 1xmic 1xheadphone 1xaux.but wen using a surround system they all change 2 inputs for the speakers?
soz 4 being a dumb ass lol. just dont wanna kill anythin

thanx in advance 4 the help folks

A:mobo audio input help

it looks that way - i dunno what you're supposed to do if you want to use the mike whilst gaming in 5.1 - is there not a mike input on the front?

it seems to be a trend amongst hardware designers to double up the 'ports' like that - for instance, on my netbook, the same jack socket is used for headphones and mike. you have to buy a special gizmo if you want to use both at the same time. is it really an economy thing - how much money do they really save by not giving us extra sockets?

don't worry, you shouldn't break or fry anything if you stick it into the wrong hole...
------------------------------------------

*edit* re-reading your post, you haven't got three inputs? speaker sockets are 'outputs'. maybe i'm being pedantic, but there is an important distinction.

Read other 4 answers