Over 1 million tech questions and answers.

Replace harddisk

Q: Replace harddisk

Hello Support, i wanted to know how i could replace the harddisk in my laptop. but i cant find the manual. Help is appreciated thanksPeter

RELEVANCY SCORE 200
Preferred Solution: Replace harddisk

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: Replace harddisk

As we have properly understood your issue you want to replace your hard disk in your laptop for this please follow these steps: Turn the computer off and remove the back panel. Look for any screws securing your drive to the laptop. Lift the old drive up about 30 or 45 degrees and pull it out.In its place, install the SSD and put the back panel on.Nitin singh guleria

Read other 2 answers
RELEVANCY SCORE 60.4

Hello,So i need to replace my cdrom of the laptop with a hard diski need to know what the maximum storage i can put for the ssd disk and hhd diskand Thanks  

Read other answers
RELEVANCY SCORE 58.8

I have a SONY VAIO laptop with Windows XP Home version. It crashed several times during daily uses. So I tried to format the whole harddisk and reinstall Windows XP Home version. But it failed to format the harddisk. I also tried to install Windows 2000 but got the same problem. I'm thinking of that the harddisk may got damaged. If so, the question is how to replace it? I couldnot find any instructions on it.
PLEASE PLEASE help. It affected my life so much. THANK YOU VERY MUCH!!!!!!!!!!!

Jason
 

A:How to replace harddisk for SONY VAIO laptop

check the sony website to make sure that your hdd was not a defect one that they will replace. i have a sony vaio desktop, and they are replacing many hard disk drives because they malfunction when exposed to humid or hot weather.
 

Read other 1 answers
RELEVANCY SCORE 48.4

Hello all,

I need some advice.

I recently replaced my old harddisk to a new harddisk. The old harddisk has windows xp home and other programs installed.

I did not format the old harddisk, I only took out the old harddisk and replaced it with a new harddisk. I then installed windows xp home to the new harddisk.

While I am installing programs on the new harddisk, I discovered that one of the programs do not allow me to activate the program license because I have previously activated the program on my old windows. I need to do a proper uninstallation to release the license, then I can activate the license of the program in the new harddisk.

My question is, can I take out my current new harddisk, replace it with the old harddisk, boot up as normal into the old harddisk windows, uninstall the program inside the old harddisk, then replace the old hardisk with my new harddisk again.

Will I be able to access the old windows on the old harddisk?
Will it mess up my current windows/programs settings?
Will my current new harddisk windows be able to work as normal after accessing the old harddisk windows?
I thought of accessing the old harddisk as a slave, but I do not know if it is possible to access the old harddisk and do a proper uninstall of the program?
Is there any better way of uninstalling the program on my old harddisk?

Thanks in advance.

A:Accessing Win XP on old harddisk to uninstall programs after installing new harddisk

you have to swap out the drive completely. at no time should you have both hdd plugged in.

repeat, do not run them as master and slave. run each hdd individually at each time only.........

Read other 5 answers
RELEVANCY SCORE 48.4

I have 40GB harddisk and now I am moving to 120GB SATA hardisk. But i want all the data with softwares, plugins and all the windows settings to be transferred in the 120 GB harddisk.

There is any way so that all files and setttings will transferred and I dont have to install everything again.

In my system Windows XP Pro SP1 is installed.
 

A:Transfer data/settings from small harddisk to big harddisk

Read other 6 answers
RELEVANCY SCORE 38.4

Hi all,

The laptop in question is a Toshiba Satellite A105-S4334. A few weeks ago, it got dropped right on its corner with the power plug still in it; the little metal plug of the AC adapter is now slightly crooked, and the power jack has a little chip off the plastic part of it.

Anyway, after this mishap, it worked fine for another 3, 4 weeks, and then suddenly this week, it's refusing to power up. Its battery has been shot for a while (can't hold a charge), and I've been using it with the battery out. Why the sudden refusal to boot?

I took the whole thing apart---minus the little chip, the power jack looks totally fine and cosmetically sound. Put the whole thing back together, taking care to check that plugs were snug---still no power.

Stuck in the crappy battery; booted just fine (and then shut itself down after like 2 minutes).

How likely is it that it's the power jack which is broken? And why did it take this long to crap out, if it IS broken?

A new one of those silly jacks costs over $20 on eBay, so I want to make sure that it's the jack before I just up and buy one. Of course, if it's the AC adapter that's broken, that would cost even more! Bah.

Input?
 

A:Replace the power jack or replace the adapter?

AND/OR inside the case the the jack is soldered directly to the motherboard. Is also possible that
1) It's already cracked
2) If not yet, it's gonna crack

So look to see what connection looks like between power jack and motherboard, If you feel u wanna/can re-solder yourself or the typically price to redo the whole power thing seems to run $125 parts/labor/warranty if you take it somewhere. So how much is it all worth to you?
 

Read other 4 answers
RELEVANCY SCORE 36.8

Hello...

[I need to know if there is a function...perhaps a Macro or Query...or a more complex 'Find & Replace'...that can accomplish the following...'cause my database is huge; & I'm hoping not to do this manually]:

I keep an Access database for my homeowners' association on the condition & conformity of 24 different exterior attributes, for about 2400 townhomes. The Board of Directors wants to move away from using the term "Grandfathered", which is distinguished by the acronym "GF" in the database column that shows conformity (labeled IAW). We use this database to generate annual architectural reports for our 10,000 residents.

Our board wants the entry "GF" replaced with a "Y"...they want the GF entry removed from the report completely; & they're serious about it.

Now...I have already created a Query that has located all the GF entries in their various columns of various records...which our Board wants me to use in an internal "in-office" database (in order to keep track of what attributes actually were grandfathered originally...as a reference for our field inspector when he inspects the townhomes).

But we also want to create an unassuming symbol on the report...perhaps an ~ or a *...something that will alert the inspector to an attribute that once was grandfathered, on his field report. [This is to be done so that he will not
be flying blind when he comes across a non-con... Read more

A:Find & Replace (but Replace in a different Column)

see attached. But actually getting that data back to the table, if that is what you want, is a bit trickier.
 

Read other 3 answers
RELEVANCY SCORE 36.8

For some reason W7 has decided to change 'Copy and Replace' with 'Move and Replace' when picking a file up with the left mouse and dragging it to another folder where an old version of the file exists.

My Excel SS is in two places: My desktop and USB which I use for backup. I would simply open the folder on the USB pick up the file on the desktop with the left mouse and drag it to the USB folder. Then I would get the message 'Copy and Replace'.. But not anymore it's become 'Move and Replace'.

I know I can 'Copy and Replace' by holding down the Ctrl key but I dont want to.

It looks like there should be a simple answer

Can anyone help? I swear I didnt change anything.

A:How can I 'Copy and Replace' not 'Move and Replace'.

Hi,
Have you ever tried right click drag and drop ?
There will be a list option after you drop,
Cheers.

Read other 8 answers
RELEVANCY SCORE 35.6

We have a TON of text based INI files for our companies software deployment scripts.

We also have a TON of people who use different ways to deploy the same software. On one server alone we can have a bunch of different ways people install E.G.

msiexec.exe /quiet /norestart /i \\dfs\dfsshare\SAV\Symant~1.msi
msiexec.exe /quiet /norestart /i <qt/>\\server\share\WIN32\Symantec Client Security.msi<qt/>
msiexec.exe /quiet /norestart /i \\server\share\SAV\WIN32\Symantec Client Security.msi
msiexec.exe /quiet /norestart /i <qt/>\\dfs\dfsshare\SAV\Symantec Client Security.msi<qt/>

and so on down the line.

I LIKE the abilities of Ecobyte Replace Text 2.2 but the problem is I have to type in the whole line as it is in the file to then replace it with the new one for the new deployment.

What I want to do is have a search based on PART of the line so I can then put in Symant~1.msi and Symantec Client Security.msi and replace the ENTIRE line with a new line.

Is there any multi file utility that allows you to search for part of a text line but replace the entire text line?
 

A:Need a robust text find and replace utility - Like Ecobyte Replace Text 2.2 but not

Read other 6 answers
RELEVANCY SCORE 34

Ok now its been a while since my pc has not been working. Ive had it for just over a year now. One day i turned it on and it would get to the Bios splash page but it would not go any further. There were no beeps nothing. All fans run, and from what i remember hard drives would start spinning too.

I thought maybe it was a PSU problem as the PSU would have very subtle flickering sounds, almost like sparking cables. However after taking the PSU to a technician they said it was working fine. This cost me 50 AUD! What he then told me was that it may be the mobo. But before i go and send it to a proper technician and fork out X amount of money id like to get your opinion.

As i mentioned above. The pc turns on, doesnt boot past the BIOS splash screen and just stays there. There are odd noises from the PSU. Here is my setup:

ASUS A8N32-SLI Deluxe
AMD Athlon64 4000+
PC-3200 (2x1gb) CAS2 Corsair DDR mem
Radeon X800 GTO (Iceturbo 2)
Thermaltake 680w power supply
Maxtor 300gb Maxline III
WD Raptor 36GB
Creative Audigy 2 ZS

I have not had the guts to take anything out and test them individually. But has anyone had or heard of this problem before? What could it be about the motherboard that would also make the PSU make that noise? Is it just a safety mechanism of the PSU?

SOS
 

A:To replace or not to replace.. that is the question.

Hi and welcome to Techspot!!

Test the RAM sticks individually. One of them might be bad. You can use Memtest86 to try them out.

Also, try them in different memory slots. That sometimes helps.

Regards :wave:

BTW, Great thread title
 

Read other 5 answers
RELEVANCY SCORE 34

Hi!Where can i buy sata cabel to my ideapad y700 because i have ssd but i cant connect hdd harddisk because i dont know where to buy the cabel. I only have ssd m.2 .  Please help me !

Read other answers
RELEVANCY SCORE 34

Hello,
a week ago i transferred a list of archived files to my mp4, then the light went off ,when it came back, i can't find the archives on the partition , nor the mp4

also some sound files disappered from the mp4, also files are occupying space whether on the hard disk or the mp4

i tried to show hidden files, but i still can't find the files

so what's wrong ?? , how can i get the files again ??? because the computer shows that they are still occupying space

thanks in advance

Best regards,

A:HardDisk & MP4

  
Quote: Originally Posted by Mitooo


Hello,
a week ago i transferred a list of archived files to my mp4, then the light went off


Hi.

Does that mean you lost power to your computer or drive?







  
Quote: Originally Posted by Mitooo


because the computer shows that they are still occupying space


If you lost power whilst transferring, there is a good chance some of the files will have become corrupt.

Read other 5 answers
RELEVANCY SCORE 34

My computer came with a 10gig hardrive with Windows Me preinstalled. I upgraded to Windows XP Home Edition and have been very impressed it was well worth the 90 I payed for the upgrade pack! I purchased 64MB of RAM to bring my memory from 64MB to 128MB and my computer hasn't crashed ONCE since I got XP! But having two operating systems on one 10 gig hardrive and lots of preinstalled programs such as office has taken its toll and I was warned the other day that my harddisk was nearly full! I deleted all my unnessesary files and managed to get back 1 gig of space but I'm still not happy and would like to get a new 20gig hardrive. It makes more sense to use my recovery disk to return my computer to the way it was when it left the factory and reinstall windows XP on the new harddrive leaving my old operating system on the old C:\ and installing all my programs into the new harddrive. I have two questions about this:

1) Will my computer become dual-boot which i DONT want to happen I want the same setup as I have know but with XP installed on the new harddrive?

2) Will I be able to call my new harddrive B:\ as I don't have a 5 1/2 floppy drive installed and would prefer to have things organised and call it that, if not what will my drive call itself as default as I already have A,C,D,Q,R drive letters already taken?
 

Read other answers
RELEVANCY SCORE 34

My computer came with a 10gig hardrive with Windows Me preinstalled. I upgraded to Windows XP Home Edition and have been very impressed it was well worth the 90 I payed for the upgrade pack! I purchased 64MB of RAM to bring my memory from 64MB to 128MB and my computer hasn't crashed ONCE since I got XP! But having two operating systems on one 10 gig hardrive and lots of preinstalled programs such as office has taken its toll and I was warned the other day that my harddisk was nearly full! I deleted all my unnessesary files and managed to get back 1 gig of space but I'm still not happy and would like to get a new 20gig hardrive. It makes more sense to use my recovery disk to return my computer to the way it was when it left the factory and reinstall windows XP on the new harddrive leaving my old operating system on the old C:\ and installing all my programs into the new harddrive. I have two questions about this:

1) Will my computer become dual-boot which i DONT want to happen I want the same setup as I have know but with XP installed on the new harddrive?

2) Will I be able to call my new harddrive B:\ as I don't have a 5 1/2 floppy drive installed and would prefer to have things organised and call it that, if not what will my drive call itself as default as I already have A,C,D,Q,R drive letters already taken?
 

A:Harddisk!

Read other 12 answers
RELEVANCY SCORE 34

Hi which would be the best free hardrive checking tool that would tell me if something is failing or is dead

A:harddisk

http://www.seagate.com/support/downloads/item/seatools-win-master/
http://www.seagate.com/support/downloads/item/seatools-dos-master/

Read other 7 answers
RELEVANCY SCORE 34

i have an old hdisk on an old pc.
the disk label shows that is 4+ Gigs
when i try to fdisk and format, only half is available
at fdisk options appears to be only 2+Gigs
wtf?
 

A:only 1/2 of harddisk is there!

Read other 6 answers
RELEVANCY SCORE 34

I have an ultraDMA harddisk from compaq. I hope to know what is the ATA and RPM value of my 20GB drive. Is there some software that I can use to check it?
 

A:Harddisk

The only 20 GB HDD I could find on the Compaq site is 20GB Ultra ATA 100 Hard Drive (7200rpm)
251974-B21

This was at http://www.compaq.com/products/desktops/options/options_storage1.html
That doesn't mean that there aren't more. The way to know, for certai8n, is to open your system up, and get the part number, or full specs from off the HDD case itself.
 

Read other 2 answers
RELEVANCY SCORE 34

Hey can anybody tell me which is the best harddisk drive for which i should go??????????I need atleast 250 gb or more of diskspace so suggest me the best HDD with their latest price ????????Thankyou.
 

A:Best HARDDISK

Get Seagate 500GB SATA-II

125bucks.
 

Read other 23 answers
RELEVANCY SCORE 34

hi

i have a western digital 160gb caviar blue hd now i want to buy a new one but some questions are bothering me

first is seagate any better than western digital i ask this because 1tb seagate is just slightly expensive than 500gb western digital so should i go for seagate?

second is that if i buy seagate, will it cause any problem to the system having one wd hd and one seagate?

please answer in details would love to hear anything to increase the knowledge

A:help about a new harddisk?

1. you can mix any makes of disks. They are all 'compatibel'.

2. the make does not matter. They are all the same since they all come from the same factories in Thailand. I have a dozen different makes and do not notice any difference.

3. except Seagate - one of those just died on me. The first and only disk that died in my installations.

Read other 6 answers
RELEVANCY SCORE 34

I am trying to setup the 3rd Hard Disk in my CPU. It doesn't seems to able detect my already formated hard disk. Is it possible to have 3 Hard Disk in 1 CPU? If so, how do should I go about it? Do I need to do anything with the Jumper on the Hard Disk?
 

A:3 HardDisk in 1 CPU

Read other 7 answers
RELEVANCY SCORE 34

I have an 80GB IDE Hitachi HD which was formatted NTFS on my computer running Win 7 Ultimate. My problem is that when connected to my computer via external Sharkoon Drive link USB adapter, it is not shown in Windows Explorer but is shown in Device Manager as USB Device and in Computer Management it is shown as ?Disk 1 ? Not initialized? and when clicking on to initialize, an error shows as ?This device not ready?. Same occurred on another PC running Vista Ultimate. Strangely, when connected to IDE inside PC it works perfectly. Can anyone help please?

ASUS P5GC-MX/1333 MB
500GB sata Hitachi HDD
2GB Ram
3.2GB CPU
Windows 7 Ultimate

A:USB Harddisk

Does the USB adaptor work correctly with any other drive?

Read other 4 answers
RELEVANCY SCORE 34

Hello,

Re: Win98SE - Intel 465 Mhz

The harddisk in my PC is 8 GB of which only 2,56 GB is still available now.
From I similar PC (done away in the meantime) I still have a 8 GB IDE harddisk.
and want to place it in my PC.
Please mind that I have never opened a PC sofar.

a) I don't know to what electronic circuit-cable it must be connected (wondering about serial and parallel)

b) then this second harddisk must somehow be connected to and made visisable to the system (by cables I think; however what cables, new ones or
already present)

When I tried to google this subject I only found items on partitioning etc, not
about how to get and connect a second harddisk inside a PC.
Furthermore I have no idea whether there are special well-known problems
related to having a seond harddisk installed (e.g. very slow system)

Advises will be highly aprreciated.

Best regards,
a.ruiter
 

A:add a second harddisk

This may help http://www.perfectdrivers.com/howto/seconddrive.html
 

Read other 3 answers
RELEVANCY SCORE 33.6

hi, My HP 255 G3 doesn't boot any more. The harddisk check gives FAILURE ID 9AJE04-7LW8H2-XD7V7A-61CQ03.I could now buy a new harddisk, but that would come without OS. The OS was pre-installed on the harddisk, so where do I get that from? Or can I somewhere buy a new HD with pre-installed OS? thanks,/conny

A:Harddisk failure HP 255 G3

Hello Conny2003, No Harddrive will come preloaded with OS.  If you want the HDD replaced and OS reinstalled together, you will have to send the laptop to HP for service. This will done free of cost if your laptop is under Warranty. If not under warranty, you will have to call HP and look out for Out of Warranty options and charges are applicable. Whenever the Hard Disk Short/Long DST test fails that indicates that the Hard Disk Drive has failed and that requires a replacement to resolve the issue HP will provide a replacement Hard Disk Drive if the Notebook warranty is Active, If not you need buy a SATA Hard Disk Drive from a retail shop nearby  Please Contact HP if your HP Notebook is under warranty, HP would replace the Hard Disk Drive and provide you a Recovery media to restore factory operating system after replacement (if you've not yet created Recovery Discs/USB Media) Note: Back up all the personal data to an external drive if it's possible. Otherwise you could connect the failed HDD via SATA to USB adapter with another PC or same PC after replacement of HDD & re-installation of OS and try copying /recovering the files. You can also refer to the below shown link for further supporthttp://www.wikihow.com/Recover-Data-from-the-Hard-Drive-of-a-Dead-Laptop Please click on the link In order to Identify, Prevent, Diagnose & Recover from Drive Failures on HP Notebook Hard Drives & Solid State Dr... Read more

Read other 1 answers
RELEVANCY SCORE 33.6

I'm trying to figure out how I can interpret this:

\Device\HarddiskVolume7\$mft

for Windows 2000 server
 

A:harddisk volume

That's the Master File Table - with an NTFS volume, it's what tells the system where on the hard drive each file is located.

If that file gets corrupted, you will get file system errors.

It can be repaired by running a CHKDSK on your drive (alternatively with the /R parameter, to repair bad sectors, or at least move any recoverable data from a bad sector to a new location.)
 

Read other 1 answers
RELEVANCY SCORE 33.6

I have a 210GB Hard drive and apparently i only have 16GB of space left. This didn't look right to me so i went into my Cdrive and checked the size of each folder and added them up on a calculator. Not counting folders that were a few MB or KB the calculator told me i have only used approximately 146GB of space. I ran a defrag and cleanup only a few days ago. So what's going on?

Here are the folders in my C drive:

Program Files = 2GB
Program Files (x86) = 70GB
Windows Folder = 23GB
Users = 44.6GB
SwSetup = 6GB
Temp = 0 bytes
PerfLogs = 0 bytes
Intel = 604KB
inetpub = 188KB
IExp1.tmp = 0 bytes
IExp0.tmp = 0 bytes
Games = 126MB
col1832 = 2.16MB
ATI = 248MB
AMD = 3.87

A:HardDisk Problem

Are you counting hidden and system files?

Read other 9 answers
RELEVANCY SCORE 33.6

Hi all,

I have some harddisk space problems, where i need your help.

I have allocated 100GB for my system drives, and 50GB is the actual space used for the system, while the balance is free space. This morning, i notice that about 32GB has been "used", and the balance free space shown is 18GB. I have look through all the folder, in cluding hidden file in the system drive...but...is fantastic, i sum up with total 50GB.

Where my 32GB gone????

Thank you,

Best regards,

Puah

A:Harddisk Space

that happen to me too harddisk space gone so fast.

i think it is because of a harddisk virus that eat your harddisk space .

so maybe do a defrag and scan your computer for virus and spyware.

Read other 7 answers
RELEVANCY SCORE 33.6

i have hitachi 80 gb external usb harddisk. It has two partition yesterday night i am working on it but suddenly i am not able to access my hard disk so i unplugged harddisk.

now when i click on this drive it gave me error "file and directory is corrupted or unreadable" so i format my drive after almost completion it gives error "windows is not able to format this drive".

when i restart my computer and i click on this drive it gives message "this disk drive is not formated do you want to format it now?" it has two partition so when i click on other partition it works ok but this partition has some problem

when i click on this drive it shows me 0 bytes in used space and 0 bytes in free space. Now what to do i also check this drive with check now but no window is open and check now is not started what to do?

my data in this drive is not important can any software help me for this problem
 

A:external usb harddisk

Read other 7 answers
RELEVANCY SCORE 33.6

I had to do a clean reinstall of Windows 7 as my PC was getting slower and slower and really bloated. After the OS install I also installed FF, Thunderbird, Alibre Design (170Mb installer), MoI (16Mb installer) and Avira. Not a lot, right?

It seems though that only 129Gb of my 148Gb harddisk is still available. 19Gb for an OS and a few piddly programs?!

A:What is using my harddisk space?

Don't know if this is the reason but installers are usually much smaller than the actual program. Just as an example, the free Nitro PDF reader says the installer is 28MB, but the installation footprint is 106MB, and it can use up to 335MB of available hard drive space.

About

If you go into control panel > programs and features it may show the size of each installed program, app, etc. And don't forget to include other things like Windows Updates, whether or not you've installed IE9 or some other browser, your anti-malware suite, etc.

Read other 9 answers
RELEVANCY SCORE 33.6

Hi bro, just a question which company's internal hard disk is good and very stable. I have been using seagate for long time, i believe company's reputation has gone.I replaced my 320 gb hdd for several times , even though company gives 5 year warranty but no use.I was replacing my hdd continually and so many times data losses,recently just a weak back my hdd has come from replacement, just with in 5days of time again status of hdd has degraded. I'm really fed off with this hdd(seagate) prior to this same case with 250 gb. So which internal hdd is best(cost effective).

And please let me know that any incompatibility of my system is causing frequent hard-drive failure , I will provide with full specifications of my system. Myself i built this system.

Core2duo E7300
GA-Ep43(gigabyte mobo[no display board])
4gb(2+2) 667mhz
320gb seagate hdd ( 2008 june)
d-link wireless desktop adapter
Nvidia 9800gt of 1gb DDR-3
LgDVDrom
I-ball gaming cabinet with 600watt smps.

Cooling-additional 4 powerful fans and default 3 fans

regards
sandy
 

A:internal harddisk

If it's a computer I advice getting an external hard drive, you can get 1TB for like $40, and internally I'd go with Acer, of all the Acer computers I own, none of the hardware has ever failed. Yet, with HP, the HDD, mintor, CPU, fan, and some other stuff, all broke in less than a year.
 

Read other 2 answers
RELEVANCY SCORE 33.6

How to Format harddisk by win xp c.d and for windows related problems(including servers), once visit the following site

http://technodata.blogspot.com
 

A:Format harddisk by win xp c.d

Welcome to TSG....

Good site I really like it and I will pass it around as needed.

Thank you and hope you stay here at TSG....
 

Read other 2 answers
RELEVANCY SCORE 33.6

Hello! can anyone help me to solve this problem please?
i want to resize drive C: because it too small. is there any software to deal with this problem? right now i'm using window 7 with system type: 64 bit.

A:need help for resizing harddisk

Paragon Partition Manager v10 works well with Windows 7 x64

Read other 3 answers
RELEVANCY SCORE 33.6

Good morning.I have tried everything that's possible with my laptop.I can't get it to work. I try to do a factory reset but nothing.Is it not possibe to get a windows 10 recovery USB stick from hp support?or Ihave bought one, where can I get one?

Read other answers
RELEVANCY SCORE 33.6

i bought an external hard disk its western digital 320gb, i observed data transfer rate of that disk is 30-40mbps only but ability of usb2.0 is 480mbps, how come very less data transfer, is there any way to increase it or any other application to increase it.

help me in resolving
thanking you
sandy
 

A:external harddisk

Transfer rates externally (i.e. USB or Firewire) are recorded in mega bits per second, however ATA and IDE protocols are measured in mega bytes per second. This means 480bp/s translates to 60MB/s (taking into consideration 1 byte = 8 bits). It seems the speeds on external USB drives are bottlenecked at around 40MB/s anyway - so if you're missing out, it won't be by too much.

Speeds also depend on how your external drive (well, inside the enclosure) works and reads the information off the disk. For example, reading from the outer edges of the disk will result in faster transfer rates than if it was reading from the inner part of the disk.
 

Read other 1 answers
RELEVANCY SCORE 33.6

hi
At present I am using a hitachi 80 GB SATA hard disk.It is so insufficient so I am planning to buy Samsung 500GB SATA.Now if I add the new HD what would happen to the previous one?(80 GB hitachi).Will it remain or replaced by the new one?Let it is possible to add the new one with old one(80+500=580) then reinstalling the operating system(xp sp3) is reqired?
 

A:New harddisk question

Read other 12 answers
RELEVANCY SCORE 33.6

Would i be able to connect a 200mb Harddisk to my compter, to copy the contents into an image with Norton Ghost. I have IDE CD CDRW and Hardisk already and would make this disk a temp Seconary slave. My mother board is June 2000 Bios dated im guessing this would auto detect 200mb disk. What Specs do u think 200mb disk would be any any probs which might arise?

Cheers guys
 

A:OLD 200mb HardDisk.

Yes that should work. Just use auto geometry. Mobo's IDE is backwards compatible.

I don't think you would want to keep it on there long after the data was copied off of it, though. Such an old device is just taking up a valuable IDE channel.
 

Read other 2 answers
RELEVANCY SCORE 33.6

Dear members,
I bought a new 320 GB harddisk (Seagate, ST3320620A). First, I open my Computer's case then pluged it as the secondary harddisk for formating it. It's done, I can find my new drive. Then, I took it out and put it into the external case to use it as the portable-external harddisk. But when I connected it to my computer using USB cable, my computer cannot see the new drive. Normally, this case may be happen, if you haven't enough USB power supply. But in my case, the external case provides the power supply too (with AC adapter). Moreover, I tried to change the USB cable to the another good one, it's still not working.
However, I connected it to my friend's computers, some of them can work properly but some cannot work. Is it the USB driver problem? How should I do?

--I use Windows XP Professional (lastest update) on Dell Optiplex GX280.

Thank you very much,
 

A:Cannot found 320 GB Harddisk

Hi Ceowebmaster and welcome to the TS Forums

I dont get this part of your post.





ceowebmaster said:



However, I connected it to my friend's computers, some of them can work properly but some cannot work. Is it the USB driver problem? How should I do?Click to expand...

Mostly when an HD in an external closure is not seen by the OS it is because the HD is set to cable select not master.

If however the enclosure works OK on another machine then yes you have some kind of USB issue, the easiest cure for this is to remove all USB related items under Device Manager and then reboot, XP will refind the items on bootup and reinstall them.

Please explain your post or let us know if the abvove is of help.

Regards
 

Read other 1 answers
RELEVANCY SCORE 33.6

I can no longer detect my 320GB HD, well... sorta, it's partitioned into 2 drives, one is viewable while the other is not. Under Window's Defragment, it says it's an unmounted volume - how can I re-mount it?
 

Read other answers
RELEVANCY SCORE 33.6

Is there a way to format new harddisk in xp pro. I already have n operating HD with xp pro installed. When i put in an unformatted harddisk, it does not detect my harddisk. The jumpers are correct. I have to disconnect my original HD and format the new harddisk using my dos bootup disk. Is there a better and easiler way to add on new hardisk without having to do all those onnecting and disconnecting?
 

A:format new harddisk in xp pro

Read other 6 answers
RELEVANCY SCORE 33.6

Hi,

I have hitachi 320 Gb Hardisk and it got bad sectors i tried windows chkdsk but its not worked so i am trying to do low level or zero level format .
So i have certain queries please help it to solve them
1.I laptop cd drive is not working so can i use it through usb & how.
2.Does it really solves my bad sectors problem..I have heard that if it stuck in between hadrdisk become useless is it right..???
3.Currently its showing 397 bad sectors on disk surface according to software Hard Disk Sentinel

Operating System Win 7

A:Bad Sectors on Harddisk

Currently its showing 397 bad sectors on disk surface according to software Hard Disk SentinelHi -This program is not one that I am familiar with, but it sounds like many Registry Fixers that show 200 problems, and say" for $50 we can fix these" I would be very careful about believing all that this program is telling you about your system !!The Hungarian or German company behind this program seems to offer very little support to their program, and also seem to want your money -Run chkdsk /r first and see if the report is the same as this HDS program reports to you, as your inbuilt diagnostics are usually better than some 3rd party programs -Method 1: Run As Administrator from shortcutUse this method and type chkdsk /r at the command -Thank You -

Read other 6 answers
RELEVANCY SCORE 33.6

Hi, can I add a second M.2 storage driver to my Lenovo Think Centre M710t?

Read other answers
RELEVANCY SCORE 33.6

i got a problem with my Toshiba laptop.my Hard disk is not found in BIOS, and i think my hard disk is ticking.[hitachi travelstar 80gb SATA my hard disk]. and these problems are showing every time i start my laptop..
1.pxe-e61 media test failure, check cable
2.pxe-m0f exiting intel boot agent
3.operating system not found..
and i have a os of windows 7.
what should i do?? please help me and thanks in advance
 

A:harddisk problems

Read other 9 answers
RELEVANCY SCORE 33.6

Hey there

I'm having a weird issue with booting up my computer and I'm hoping to find a solution that does not involve reinstalling windows completely. Might come to that, but first I'm looking for other issues.

To give some context:
A few months ago my primary harddisk started failing. I acquired a new harddisk, installed windows on it and it has been working fine.

When I boot up the computer, I can select between the old and the new windows installation and I've simply been using the new one. I've left the old harddisk plugged in as I had some data on it I wanted to salavage and then I just left it there. I've gotten the data of it and have had no reason to unplug it.

Recently, however, I wanted to unplug the old harddisk as there has been some issues with hangups and I had a suspicioun they were caused by windows (for some reason) reading from the old harddisk.

When I unplugged it I got a "Bootmgr is missing" error and could not boot up. Thus I need to have the old harddisk plugged in in order to boot up windows.

WHich is annoying, as I think the old harddisk is the cause of the performance issues I've been having.

Obviously the new harddisk has not been made bootable by installing windows on it. The old harddisk was plugged in when I installed windows, so that's likely the cause of it (for some reason...?).

Is there any way for me to fix this without unplugging the old harddisk and installing windows again? I'd rather ... Read more

A:Cannot Boot from Harddisk

The Windows installer will put its boot-up code (the bootmgr) on the primary hard drive regardless of the drive that Windows proper is installed on. You can repair this by booting your Windows 7 DVD and running the Startup Repair tool. See Microsoft's how-to article here. Make sure that the original disk is unplugged before attempting this repair.

Read other 7 answers
RELEVANCY SCORE 33.6

I want to set a password to my Harddrive of computer. I also do not know how does it help to keep hard drive secure.
Also please suggest a freeware for folder lock (other than folderlock software).
 

A:Harddisk password

this is set via the bios
as the PC starts it should flash on the screen for a few seconds how to get to the bios/setup
often at this point you press a key to enter
depending on make an model of your PC
could be <F2>or <F10> or <Del> or another key

In the bios will be a section, probably security to set a bios / harddrive password
in some cases just setting the bios also sets the harddrive
BUT
if you forget the harddrive password - remember if you forget the password , you will not be able to access the harddrive , even if you put it into a different pc
 

Read other 1 answers
RELEVANCY SCORE 33.6

hi
i have a mdf file on a cd which i try to copy from the cd to the harddisk...it doesnt...it gives an error which says

error copying file or folder

Cannot copy mir-popt2t.mdf there is not enogh disk space

the size of the file is 4.6gb and the drive i am trying to install it to has more than 20 gb free

waT SHUD I DO?
 

A:cannot copy from cd to harddisk

You posted it in the wrong forum. Please try to get it in the right forum for a faster response, or a response at all.

If the file is 4.6 gigs, its on a dvd and not a cd, but regardless, what file system is that hd formatted in? If its FAT32, right there is your problem, FAT32 can't handle files over 4 gigs in size. You will need to convert the FS to NTFS if you are on a Windows machine.
 

Read other 1 answers
RELEVANCY SCORE 33.6

Hi,
 
Toshiba L750, core i5 - win-7 64bit installed. 4gb ram, 600gb HDD,
50gb os, 250gb, 250gb partitions. 8gb Virtual memory on 3rd partition.
 
Used sparingly and working fine until a few days ago. I heard some faint whirling sound (probably the HDD) and in some time the OS crashed.
It went into an infinite loop of shutting down and rebooting trying to recover the system.
 
At some time, I chose command prompt and ran chkdsk on all the partitions chkdsk /f /r
 
It seemed to work, although the computer was only half as fast.
 
After a couple of boots, I only get a blank screen and a cursor at left hand top, post the bios screen.
 
Has my harddisk crashed? If so, how do I get it working back, either with the same HDD or another one
The data is not really important to me ( I have a back up on my desktop)
 
Thanks in advance for your help

A:Has my harddisk crashed ?

Yes it sounds like it.  Here is a video showing you how to replace it.

https://www.youtube.com/watch?v=svTUrXrAa1U

Read other 15 answers
RELEVANCY SCORE 33.6

Hi,
 
i have a Problem with a System that i don't know how to fix. Every time I start a programm the Harddisk runs with 100%. CPU and Ram are normaly.
The space is half fulled (500GB). It's an Acer Notebook with Windows 8.1 and now it is upgradet to Windows 10. I call Acer and they told me that the
Problem is a Microsoft Update that possibly comes in when Windows 8.1 was aktiv.
Does anyone know thomething about this update?
 
Thanks for help,
 
Aitora
 

A:Harddisk runs by 100%

Please download and install Speccy to provide us with information about your computer.  Clicking on this link will automatically initiate the download. 
 
When Speccy opens you will see a screen similar to the one below.
 

 
Click on File which is outlined in red in the screen above, and then click on Publish Snapshot.
 
The following screen will appear, click on Yes.
 

 
The following screen will appear, click on Copy to Clipboard.
 

 
In your next post right click inside the Reply to Topic box, then click on Paste.  This will load a link to the Speccy log.
 
 

Please download MiniToolBox to your desktop.
 
Right-click on MiniToolBox.exe and select Run as Administrator.
 
You will see an image like the one below.
 

 
Click on the following checkboxes only:
 
• List last 10 Event Viewer log
• List Installed Programs
• List Users, Partitions and Memory size.
• List Minidump Files
 
Click on Go to start the scan.  Once it is finished highlight the text, then copy it and paste it in your topic.

Read other 1 answers