Over 1 million tech questions and answers.

BSOD after turning computer on from sleep DRIVER POWER STATE FAILURE

Q: BSOD after turning computer on from sleep DRIVER POWER STATE FAILURE

I am getting a BSOD mostly when I turn the computer on from sleep mode during sleep wifi will be on and most probably 1 of the browsers would have been working.

Reinstalled Windows 7 on Oct 8 and downloaded some drivers from the net.

I have uploaded the SF diagnostic zip file

Any help would be greatly appreciated

RELEVANCY SCORE 200
Preferred Solution: BSOD after turning computer on from sleep DRIVER POWER STATE FAILURE

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: BSOD after turning computer on from sleep DRIVER POWER STATE FAILURE

Welcome aboard. Is there any reason that you haven't installed service pack 1?

Read other 9 answers
RELEVANCY SCORE 118.8

I've started getting driver power state failures BSODs after my computer goes to sleep.

These started in the last couple of weeks. It's happened twice today already. When I first noticed these occurring, I used System Restore to undo my last installs, but it didn't help.

I'd greatly appreciate any help fixing this.

A:BSOD after going to sleep, driver power state failure

Welcome

Your Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC is causing BSoD
Update to latest drivers

Code:
>[ 16, 2] 0 e1 fffffa8005c3a050 00000000 fffff800032d5200-fffffa8007049c50 Success Error Cancel pending
Unable to load image \SystemRoot\system32\DRIVERS\Rt64win7.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for Rt64win7.sys
*** ERROR: Module load completed but symbols could not be loaded for Rt64win7.sys
\Driver\RTL8167 nt!PopSystemIrpCompletion
Args: 00014400 00000000 00000004 00000002
[ 0, 0] 0 0 00000000 00000000 00000000-fffffa8007049c50

Args: 00000000 00000000 00000000 00000000
0: kd> lmvm Rt64win7
start end module name
fffff880`06d15000 fffff880`06d7f000 Rt64win7 T (no symbols)
Loaded symbol image file: Rt64win7.sys
Image path: \SystemRoot\system32\DRIVERS\Rt64win7.sys
Image name: Rt64win7.sys
Timestamp: Wed Jan 26 19:34:03 2011 (4D4022CB)
CheckSum: 0006AFBB
ImageSize: 0006A000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
Source | Driver Reference Table

Also Take memtest. Run for 8 passes and test each stick in a know good slot for an additional 6 passes.

→ RAM - Test with Memtest86+
→ Guide to using Memtest86+ - Geeks to Go Forums

Read other 9 answers
RELEVANCY SCORE 118.8

Been having issues with sleep mode with my build for months but in the past couple weeks it has gotten worse. When the computer goes into sleep, there's about a 50 percent chance it will wake up when I move the mouse. The other times I have to hard restart. In the past week it is now BSODing and giving me the attached dump reports. I'm pretty sure it's a driver issue but I can't narrow it down any more than that. Interested to hear what the experts think.

A:BSOD DRIVER STATE POWER FAILURE 9f, on sleep

Hi slash196.

Update the driver to TP-LINK 150Mbps Wireless Lite N Adapter from Download - Welcome to TP-LINK, by matching with your device number.

Install Service pack 1 and all other windows updates. Otherwise the system will remain vulnerable to threats.

Code:
OS Name Microsoft Windows 7 Ultimate
Version 6.1.7600 Build 7600
Learn how to install Windows 7 Service Pack 1 (SP1)
Service Pack and Update Center - Microsoft Windows

Also, if possible, update the BIOS to Version 1501 from ASUSTeK Computer Inc. -Support- Drivers and Download M4A88TD-M/USB3

Let us know the results.

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa8006a9e060, fffff80000b9c518, fffffa800a2fb920}

Probably caused by : ntkrnlmp

Followup: MachineOwner
------------------------------------------------------------------------------------------
Dispatch routines:
[00] IRP_MJ_CREATE fffff880016e7c30 ndis!ndisCreateIrpHandler
[01] IRP_MJ_CREATE_NAMED_PIPE fffff8800177e490 ndis!ndisDummyIrp... Read more

Read other 1 answers
RELEVANCY SCORE 117.6

Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7600.2.0.0.768.3
Locale ID: 1033

Additional information about the problem:
BCCode: 9f
BCP1: 0000000000000003
BCP2: FFFFFA8009DBD060
BCP3: FFFFF80000B9C518
BCP4: FFFFFA800ED33010
OS Version: 6_1_7600
Service Pack: 0_0
Product: 768_1

Files that help describe the problem:
C:\Windows\Minidump\120410-48828-01.dmp
C:\Users\Jon\AppData\Local\Temp\WER-70980-0.sysdata.xml

Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409

If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
Yeah, i get this whenever my computer goes idle and into sleep mode, and when i shut down. Any way to fix???

minidump -- http://www.megaupload.com/?d=J07IWJQ0
 

Read other answers
RELEVANCY SCORE 117.6

Hey!

I got an BSOD from sleep mode. Was off to go outside the summer heat today and when I came back... BSOD..


However the system managed to dump two files for me on BSOD.

Take a look and thanks for the help you give me :)

A:DRIVER POWER STATE FAILURE Sleep mode BSOD.

Hello,

Please take a look at the following thread and perform all of the requested steps.

Once you have all the requested reports please attach back here.

http://www.techsupportforum.com/foru...ta-452654.html

One dump is really not sufficient to determine the cause. The reports will also provide other info to help diagnose the issue.

The dump provided indicates a problem with the Realtek Network driver please try updating or re-installing this driver.

Realtek

I would also suggest that you fully update Windows including the Windows 7 Service Pack.


Code:
Windows 7 Kernel Version 7600 MP (4 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16617.amd64fre.win7_gdr.100618-1621
Machine Name:
Kernel base = 0xfffff800`03268000 PsLoadedModuleList = 0xfffff800`034a5e50
Debug session time: Fri May 10 12:00:54.715 2013 (UTC - 4:00)
System Uptime: 0 days 8:41:33.010
Loading Kernel Symbols
...............................................................
................................................................
...........................
Loading User Symbols
Loading unloaded module list
......
*******************************************************************************
* *
* Bugcheck Analysis *
* *... Read more

Read other 2 answers
RELEVANCY SCORE 117.6

Hello, all. Every now and again my laptop BSOD's when I leave it on sleep mode over night. Today the laptop lit up and started running while it was closed and I opened it to see the Driver_State_Power_Failure error message. Attached are the files gained from the SF Diagnostics Tool. Any help is greatly appreciated.

A:BSOD During Sleep Mode - Driver State Power Failure

Hello fran.

It appears that Avast is causing the BSODs there.

avast! Self Protection Driver

Code:
fffff880`02677de8 fffff880`068e2940Unable to load image \SystemRoot\System32\Drivers\aswSP.SYS, Win32 error 0n2
*** WARNING: Unable to verify timestamp for aswSP.SYS
*** ERROR: Module load completed but symbols could not be loaded for aswSP.SYS
aswSP+0x2f940
Description here: Driver Reference Table - aswSP.SYS

avast! Virtualization Driver

Code:
fffff880`02677d68 fffff880`066d32ccUnable to load image \SystemRoot\System32\Drivers\aswSnx.SYS, Win32 error 0n2
*** WARNING: Unable to verify timestamp for aswSnx.SYS
*** ERROR: Module load completed but symbols could not be loaded for aswSnx.SYS
aswSnx+0x4e2cc
Description here: Driver Reference Table - aswSnx.SYS

Uninstall Avast using Avast Uninstall Utility. Use Microsoft Security Essentials as your antivirus with windows inbuilt firewall, and free MBAM as the on demand scanner.
Download, install and update those, and then run full system scans with both of them, one by one.

Using more than one antivirus program is not a good practice. It will make your system unstable in turn. Uninstall McAfee Using McAfee Removal Tool.

Daemon Tools, Alcohol 120% and Power Archiver Pro uses SCSI Pass Through Direct (SPTD), which is a well known BSOD causer. Uninstall Daemon Tools at first. Then download SPTD standalone installer from Disk-Tools.com, and execute the downloaded file as guided below :
Double click to open it... Read more

Read other 1 answers
RELEVANCY SCORE 117.6

Dear Sir/Madam,

I've been having this issue since updating to Windows 8.1. I will wake my computer from it's sleep and a few minutes later I get the BSOD. In one notable event early on, I got two in a row after the computer restarted from the previous BSOD.

I fiddled with my power settings (I was trying to avoid my computer actually shutting down during sleep/hibernation) a few months ago and after that I didn't have any BSOD events that I recall until this past week. When they do happen, they tend to happen in rapid succession, as you can see from the dates on the collected data I've attached (I see there's a .txt file with all my computer's information for you reference) - I've had one every day for the past three days.

I've read through many of these threads and tried several of the solutions. I am running verifier.exe since the BSOD has started up again since from what I can understand from reading the .dmp file and this forum that the message I'm getting about ntoskrnl.exe is misleading (?).

Please take a look at the dumps and other information collected from the DM Log Collector Tool and let me know if you can help me solve this problem.

Thank You.

A:BSOD Waking from Sleep (power state driver failure)

Hi, pnutbudder,

I've been having a similar problem since a few weeks ago. I suspect this is due to a recent Windows or driver update, since both of us had the same problem at the same time. I'm going to take a look at your dump files in a few hours, but in the meantime, could you tell me

1. whether you have Evernote or any Blizzard games installed
2. whether you've installed any new programs recently,
3. what graphics drivers you have installed,
4 what music or audio programs you have installed (eg, music players, movie editors, music studios and recording programs, game streaming programs)?

EDIT: Okay, I took a look at your dump files, and they point to a bad interaction between the "usbccgp.sys" and the "ksthunk.sys" driver. These are the same drivers that are misbehaving on my system, too (Lenovo Y510P). As far as I can tell, the only device that uses ksthunk.sys is the Lenovo EasyCam. Try this fix:

1. Download the "Broadwell" version of the camera driver on this page: http://support.lenovo.com/us/en/prod...loads/DS101169 . We're going to replace your current camera driver with Lenovo's original camera driver.
2. Open "Device Manager" by right-clicking on the lower left corner of the screen.
3. Double-click "Imaging Devices" to open it.
4. Right-click "Lenovo EasyCamera" and click "Disable". You should see a small downward-pointing arrow appear next to the picture.
5. Right-click "Lenovo EasyCam... Read more

Read other 5 answers
RELEVANCY SCORE 117.6

I have tried to test this issue my self by trying to read trough the DMP file and Event Viewer. (haven't done this before, so i think i have possibly overlooked something)
The computer model is: HP ProBook 430 G2
The things i have tried is uninstalling and updating the drivers.
Using another OS Disk (It worked fine when doing this)
Starting in safe mode (This also worked fine)
Checked advanced power settings (Was nothing wrong there from what i could see)

Read other answers
RELEVANCY SCORE 117.6

New build i7 asrock motherboard W8 Pro. when waking from sleep everytime I get driver_power_state_failure BSOD.
Looking for some help on where to start. Updated the bios and everything else works great.

Thanks for any advice

Attachment 14584

A:BSOD Driver Power State Failure when waking from sleep

You have 3 hard drives - what is the make/model/wattage and age of your Power Supply?

We've seen a number of BSOD issues with SSD's. Here's the information that I've compiled so far:





There's not a whole bunch available to test SSD's. The "easiest" test is to remove the SSD, install a platter-based hard drive, install Windows and test for stability that way.

Here's some suggestions:
- Update the SSD's firmware to the latest available version (VERY IMPORTANT!!!)
- Update the motherboard controllers drivers to the latest available version from the controller manufacturer (NOT the mobo manufacturer unless you can't find any on the controller manufacturer's website)
- Slow the memory (RAM) down to the next slower speed (I've only seen one person who claimed that this worked for them).
- Use any manufacturer's utilities that you may have. If you don't have any, then try this free one (I haven't used it myself): Crystal Dew World
- Update chipset and storage controller drivers to the latest available from the manufacturer of the device (not the manufacturer of the motherboard). Be sure to update ALL controllers on the motherboard!
....NOTE: Recently (Nov 2011) we had BSOD issues with the Marvell 91xx controller and an SSD. You may have to switch controllers also.
- Replace the SSD with a platter based hard drive and see if that stops the BSOD's. If it does, then it's likely that there's a problem with the SSD OR an incompatibility with you... Read more

Read other 5 answers
RELEVANCY SCORE 116.4

Hello

I am experiencing a BSOD (DRIVER POWER STATE FAILURE) error with my ACER notebook.
It always come up after I put the computer in sleep mode.

After dozen of search and websites, I found this forum.

I hope you will be able to help me.

Please find below the informations about my OS
- Windows 7 Home Premium Edition
- x64
- OEM
- age of the system : 3 years old. The hard drive has been replaced 1 year ago.
- age of OS installation : 2 days old (reinstalled from the recovery disk)

I have also attached the System Health Report AND the BSOD Dump & System File Collection report.

Let me know if you need something else... and Thank already !

A:BSOD after sleep mode, 0x0000009f (DRIVER POWER STATE FAILURE)

Please install any Windows Updates you have not yet installed. I notice you do not have Service Pack 1 installed yet.Update to Service Pack 1 (SP1)Download Details - Microsoft Download Center - System Update Readiness Tool for Windows 7 (KB947821) [August 2011]

Download Details - Microsoft Download Center - System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [August 2011]

Steps to follow before you install Windows 7 Service Pack 1 from the Microsoft Download Center

Service Pack 1 Download site




Crashes indicate USB device issues.Start with USB Driver - General Fix for Problems to resolve the USB issues. Also, USB ports can sometimes enter a safe power state to protect the system from power surges due to USB devices. To reset the USB ports to a nominal power state:
Shut down and turn off the computer.
Unplug the computer from the wall or surge protector (then remove the battery if it is a laptop).
"Remove the computer from any port replicator or docking station, disconnect
cables to printers or devices such as external monitors, USB memory sticks or SD cards, headset or external speakers, mouse or auxiliary keyboard, turn off WIFI and Bluetooth wireless devices." (Use Hard Reset to Resolve Hardware and Software Issues HP Pavilion dv5000 Notebook PC series - HP Customer Care (United States - English))
Hold down the power button for 30 seconds. This closes the circuit and ensures all
power from components is drained t... Read more

Read other 1 answers
RELEVANCY SCORE 116.4

I'm using a Lenovo Y50 running Windows 8.1. This issue has been happening every now and then for the past week or so. I noticed it occurs briefly after waking the computer from sleep mode. I can get to the desktop but about a minute after waking, the laptop will freeze up and give me a blue screen saying it was a DRIVER_POWER_STATE_FAILURE. I'm assuming this error has to do with some driver, but I don't know how to figure out which driver is the one causing the issue. I looked in Device Manager and can't find any yellow exclamation marks pointing out issues.

Here's a link to the most recent dmp file:
https://drive.google.com/file/d/0B2kQd8xpvK9STnd3MjVFWHJJOEE/view?usp=sharing

Thank you in advance to anyone who can help me out with this!
 

A:BSoD - Driver Power State Failure after waking from sleep mode.

For the time being and for troubleshooting, please uninstall Trend Micro and just
utilize Windows Defender. Trend Micro can be reinstalled once the problem is isolated.
http://esupport.trendmicro.com/en-us/home/pages/technical-support/1105809.aspx

What is all plugged in via USB?
Did this started happening after installing/updating Razor Synapse?
 

Read other 1 answers
RELEVANCY SCORE 115.2

Hello all

This is my first post in here. Please bear over with my English – it is not my native language.

My problem is on a Media Centre machine where I recently upgraded Motherboard and processor. I have the following setup on the machine:
SILVERSTONE Grandia 04
DeZen PSU 500 Watt, TitanPower, 17-19 db
MB: Asus P8H77-MLE
CPU: Intel i3 2120
2x4 GB Corsair Vengeance ram (just bought new ones to see if it would help)
OCZ Agility 3 SSD 120 GB
1,5 TB WD Caviar Green
Asus P7131 Tuner
TERRATEC Cinergy DT USB XS Diversity
Hauppauge! WinTV-NOVA-T-Stick-Diversity
Hauppauge! Smart CI USB

My previous setup was with a AMD 240e but I have made a clean install.

I use Microsoft Security Essentials for antivirus and have firewall turned on.

The Media Centre machine is on for 24/7 on sleep mode for recordings or turned on for showing recordings.
Since the upgrade I have BSOD most times after it is turned on after sleep. The STOP occurs 4-5 minutes after the wake up either the wakeup is initiated from a recording or from user. I even see BSOD occur in the middle of the night where I have no recordings or other activity.

I have made several new install and tried to exclude the SSD and install a 32 bit Win7 – but the BSOD still occurs 4-5 min after awake.

I have updated all drivers and tried to run Verifier with no luck.

Hopefully someone can help

A:BSOD after sleep mode, error DRIVER POWER STATE FAILURE 0x0000009f

I have updated the Perfmon details - I had forgot to run the Windows Experience Index

Read other 9 answers
RELEVANCY SCORE 115.2

i guess i've been having this problem for about a month or so now and it's really becoming frustrating because everytime i have to leave my computer i have to shut it down if i don't want a BSOD..

i hope that someone can help me... every time i try to hibernate my laptop which is a HP DV4 Windows 7 Laptop i get a blue screen of death. it only started happening recently....maybe after i installed bit-defender..i'm not really sure..but it was doing fine before bit defender......

i used blue-screen view and with each time it registers a error it's with the driver for the NTOSKRNL.exe... i really hope that someone could help me because i just want my computer to go back to normal....and i wish that the problem has nothing to do with bit-defender......

tell me what you need and i'll try my best to get it to you so you can assist me with this problem cause i'm kinda new to the whole forum thing....

thanks..

A:[SOLVED] BSOD Driver Power State Failure When Hibernating/Sleep Windows 7 HP DV4

Hi and welcome to TSF please follow the instructions here http://www.techsupportforum.com/f217...ns-452654.html

Read other 17 answers
RELEVANCY SCORE 108

I've had my computer for about 3 months now, and I regularly get the same BSOD once every week or two, seemingly without any warning or provocation. Attached is my log. Thanks a lot!SAGER-JW-Sat_03_28_2015_224400_76.zip

A:BSOD Driver Power State Failure, recurring, new computer

Hi dzorror & welcome to the forums ^_^,

I have analysed your dump files and below has been provided an analysis of the same for informative purposes :-
DRIVER_POWER_STATE_FAILURE (9f)
A driver has failed to complete a power IRP within a specific time.

Code:
Arguments:
Arg1: 0000000000000003, A device object has been blocking an Irp for too long a time
Arg2: ffffe001902c1630, Physical Device Object of the stack
Arg3: ffffd001d626d960, nt!TRIAGE_9F_POWER on Win7 and higher, otherwise the Functional Device Object of the stack
Arg4: ffffe0019352cc60, The blocked IRP


Let's check the last parameter (IRP) highlighted in BLUE -

Code:

4: kd> !irp ffffe001`9352cc60
Irp is active with 6 stacks 4 is current (= 0xffffe0019352ce08)
No Mdl: No System Buffer: Thread 00000000: Irp stack trace.
cmd flg cl Device File Completion-Context
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
>[ 16, 2] 0 e1 ffffe001902c1630 00000000 fffff800cc28437c-ffffd001dab0d8f0 Success Error Cancel pending
\Driver\pci dxgkrnl!DpiFdoPowerCompletionRoutine
Args: 00000000 00000001 00000001 00000000
[ 16, 2] 0 e1 ffffe001933661f0 00000000 fffff802dd734efc-ffffe00194ee0f08 Success Error Cancel pending
... Read more

Read other 1 answers
RELEVANCY SCORE 107.2

Hi, i keep having this issue. Anyone knows how to solve?
My minidump is https://skydrive.live.com/#cid=392FCBBA17F5ACA1&id=392FCBBA17F5ACA1%21187

A:BSOD when going sleep mode "DRIVER POWER STATE FAILURE"

Related to Rt64win7.sys 8101E/8168/8169 NDIS 6.20 64-bit Driver from Realtek Corporation.

I would re-install newest driver available.

Read other 1 answers
RELEVANCY SCORE 107.2

Hello,

I left my computer on and open this morning before I left for class. When I returned, I had a BSOD, which specified "Driver Power State Failure" (I did not copy down any numbers, as I probably should have). I did a forced shut down (held the power button) and then restarted it, where it fortunately works for now.

My laptop is an Dell XPS-15, about two years old. I have not had any problems with it until now, and the past week or so it has been freezing up. I downloaded the SF Diagnostic Tool, and the zipped folder is attached.

I am uncertain what action to take next. Could someone advise me in how to fix the issue?

Thank you!!

A:BSOD after sleep or hibernation - "Driver Power State Failure"

upload your MSINFO32.nfo file.
Click on the start button
Type "msinfo32" (without quotes) in the search bar of the start menu, click the resulting link. It will open the System Information window.
File>Save. In the "File Name" filed, put "MSINFO32" (without Quote), give the save location to desktop, and click the "save" button.
Give the time for processing, it will save a .nfo file on your desktop.
Zip it, and upload it following the instruction.

Read other 3 answers
RELEVANCY SCORE 107.2

I have been using my asus laptop but recently started blue screening. When trying to shut it down the screen will go black, but the system lights remain on and it remains running, however irresponsive. It also began showing a blue screen with the warning "Driver power state failure".

Even after a factory reset this problem remains. Any help to figure out the problem would be greatly appreciated.

A:BSOD "driver power state failure", when shut down or sleep

Hi Chalcogen & Welcome to the forums ^_^,

I have analyzed your only dump file and a summary of that is given below :-

Code:
**************************Mon Jul 21 15:05:53.798 2014 (UTC + 5:30)**************************
*** WARNING: Unable to verify timestamp for win32k.sys

*** ERROR: Module load completed but symbols could not be loaded for win32k.sys

Probably caused by : memory_corruption

BugCheck 9F, {4, 12c, fffffa800aeacb00, fffff88001e9e800}
BugCheck Info: DRIVER_POWER_STATE_FAILURE (9f)

BUGCHECK_STR: 0x9F

DEFAULT_BUCKET_ID: CODE_CORRUPTION

FAILURE_BUCKET_ID: MEMORY_CORRUPTION_LARGE

MaxSpeed: 1900

CurrentSpeed: 2395


Processor may be overclocked!
Expected Frequency: 1900
Actual Frequency: 2395
Overclock Ratio: 1.26053

BIOS Version S550CM.202

BIOS Release Date 11/23/2012

Manufacturer ASUSTeK COMPUTER INC.

Product Name S550CM

??????????????????????????????????????????????????????????????????????????????????????``


Now, since the dump file blames the "Win32k.sys" which is a Windows Component, chance of it being at fault it extremely low. Below is a list of 3rd party drivers found over your system :-

Code:
**************************Mon Jul 21 15:05:53.798 2014 (UTC + 5:30)**************************
ASMMAP64.sys Thu Jul 2 14:43:26 2009 (4A4C7A36)
atkwmiacpi64.sys Wed Sep 7 07:14:52 2011 (4E66CC94)
AiCharg... Read more

Read other 3 answers
RELEVANCY SCORE 106.8

Hey All,

I've got a Lenovo T410 running Windows 7 64bit that's been having issues with a BSOD when my computer sleeps or hibernates.

BC Code: 9F

I've attached the necessary stuff. Please let me know if I've forgotten anything.

Thanks!

A:BSOD/Driver Power State Failure when computer sleeps/hibernates

Problem devices

Code:
Photosmart 5510d series ROOT\MULTIFUNCTION\0000 This device is disabled.
You will need to either uninstall the drivers and reinstall the latest version or perform a clean installation of the driver. If the device is disabled please enable it.

Drivers
The dumps point to Netwsw00.sys, a driver associated with Intel Wireless Wi-Fi Link Adapter. From the below link download and install all of the drivers Networking: Wireless LAN.
Drivers and software - ThinkPad T410

The following drivers need to be updated:


Code:
CAXHWAZL.sys Wed Jul 01 06:01:14 2009
CAX_CNXT.sys Wed Jul 01 05:59:52 2009
CAX_DPV.sys Wed Jul 01 06:05:11 2009
XAudio64.sys Thu Apr 30 04:21:07 2009
mdmxsdk.sys Tue Jun 20 07:27:26 2006
These drivers can be found by searching them in Google and then finding the associated software or driver. Finally, find the latest version of this driver or software and download and install it. Some of the drivers may also be found here (if the driver says 'Windows Update' simply make sure all Windows Updates are installed).

You should also update any other drivers you can think of including graphics, audio, chipset, SSD etc.
Software
You have Ad-Aware AV installed, is that correct? At least to test, uninstall it and install MSE (Microsoft Security Essentials) instead.
Microsoft Security Essentials - Free Antivirus for Windows

Read other 9 answers
RELEVANCY SCORE 105.2

I am experiencing an issue with my laptop where I can't allow it to enter sleep mode or else it will restart/appear to have restarted the next time I wake it up. At first I thought it might be a power options issue, but I made sure that the computer was set to sleep and not restart when I close the lid. I've checked the bluescreen viewer and the cause of the restart seems to come from a driver power state failure coming from ntoskrnl.exe+1fcc1e, hal.dll+6a37, and storport.sys+33f0.

I've already run sfc/scannow to check for damaged files and I was also able to replace them using a DISM command, so now scanning the computer doesn't run into any errors, but this driver error still persists.

Sidenote: The driver errors mainly started after I reinstalled Kaspersky onto my computer to fix some issues that I had with it. Before that I was getting a couple of kernel data inpage errors, the latest of which occurred June 1.

A:Driver Power State Failure in sleep mode

Hi M15 and welcome to the forums ^_^,

I am in the process of analyzing your dump files further. Below has been provided analysis of your dump files for Informative purposes.

Code:
**************************Fri Jun 6 04:50:12.040 2014 (UTC + 5:30)**************************Probably caused by : storport.sys ( storport!RaSendIrpSynchronous+70 )

BugCheck 9F, {4, 12c, ffffe0017919e880, ffffd00049969950}
BugCheck Info: DRIVER_POWER_STATE_FAILURE (9f)

BUGCHECK_STR: 0x9F

DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT

PROCESS_NAME: System

FAILURE_BUCKET_ID: 0x9F_4_storport!RaSendIrpSynchronous

MaxSpeed: 1800

CurrentSpeed: 1796

BIOS Version V2.20

BIOS Release Date 02/18/2013

Manufacturer Acer

Product Name Aspire M5-481PT

??????????????????????????????????????????????????????????????????????????????????????``
**************************Fri Jun 6 01:42:48.219 2014 (UTC + 5:30)**************************
*** WARNING: Unable to verify timestamp for iaStorA.sys

*** ERROR: Module load completed but symbols could not be loaded for iaStorA.sys

Probably caused by : iaStorA.sys

BugCheck 9F, {3, ffffe000d7f8e060, ffffd000ca5e9930, ffffe000da3955c0}
BugCheck Info: DRIVER_POWER_STATE_FAILURE (9f)

BUGCHECK_STR: 0x9F

DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT

PROCESS_NAME: System

FAILURE_BUCKET_ID: 0x9F_3_POWER_DOWN_disk_IMAGE_iaStorA.sys

MaxSpeed: 1800

CurrentSpeed: 1796

BIOS Ver... Read more

Read other 12 answers
RELEVANCY SCORE 105.2

Hi,
I've been getting persistent BSOD's when attempting to wake up my computer (Lenovo Twist u230) from sleep. I am also sporadically getting Kernal Data Inpage Error BSOD while using my computer.

My machine is Windows 8, installed from factory with a recent refresh done. SFC /SCANNOW and DISM both come up clean. All of my hardware diagnostics are also clean.

Help!

A:Driver Power State Failure on wake from sleep

Which hardware diagnostics have you done?

Please run Driver Verifier according to these instructions: Driver Verifier Settings

Just a guess at this point, but try removing Diskeeper to see if that helps.
If not that, then try removing the Citrix software to see if it helps.

Analysis:
The following is for informational purposes only.

Code:
**************************Fri Oct 11 09:56:37.534 2013 (UTC - 4:00)**************************
Loading Dump File [C:\Users\John\SysnativeBSODApps\101113-15578-01.dmp]
Windows 8 Kernel Version 9200 MP (4 procs) Free x64
Built by: 9200.16628.amd64fre.win8_gdr.130531-1504
System Uptime:0 days 20:21:57.335
Probably caused by :Unknown_Image ( ANALYSIS_INCONCLUSIVE )
BugCheck 9F, {3, fffffa80036b7890, fffff800c68d07f0, fffffa800de92610}
BugCheck Info: DRIVER_POWER_STATE_FAILURE (9f)
Arguments:
Arg1: 0000000000000003, A device object has been blocking an Irp for too long a time
Arg2: fffffa80036b7890, Physical Device Object of the stack
Arg3: fffff800c68d07f0, nt!TRIAGE_9F_POWER on Win7, otherwise the Functional Device Object of the stack
Arg4: fffffa800de92610, The blocked IRP
BUGCHECK_STR: 0x9F
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
PROCESS_NAME: System
FAILURE_BUCKET_ID: 0x9F_3_ACPI_ANALYSIS_INCONCLUSIVE
CPUID: "Intel(R) Core(TM) i5-3317U CPU @ 1.70GHz"
MaxSpeed: 1700
CurrentSpeed: 1696
BIOS Version GDETA1WW (1.61 )
BIOS Release Date 09/14/2013
Manufacturer LENOVO... Read more

Read other 1 answers
RELEVANCY SCORE 105.2

My Toshiba laptop gives the above BSOD screen 9 out of 10 times when going to sleep. I have installed the latest Win 8 video drivers but that was no help.

I have attached a couple of the minidump files.

A:Driver, power, state, failure when laptop goes to sleep.

Hi,

Bit of a messy machine there. First thing is first. Update or uninstall your sptd.sys. The installer/uninstaller does either:

DuplexSecure - Downloads

----------

Update Synaptics Touchpad driver:


Code:
SynTP SynTP.sys Mon Aug 17 14:35:16 2009


----------

Update J-Micron Storage driver:


Code:
jmcr jmcr.sys Mon Jul 20 07:39:02 2009


JMicron/Home

-----------

Update from the manufacturer:


Code:
tosrfec tosrfec.sys Mon Jun 01 02:58:53 2009
tosrfcom tosrfcom.sys Tue Jul 28 06:18:20 2009
tosporte tosporte.sys Tue Jun 16 06:48:47 2009
Thpevm Thpevm.SYS Mon Jun 29 04:15:37 2009
thpdrv thpdrv.sys Sun Jun 28 22:02:56 2009


----------

Uninstall ESET. Windows 8 already has excellent a/v protection as a service.


Code:
epfw epfw.sys Tue Jun 28 03:30:10 2011
eamonm eamonm.sys Tue Aug 02 05:33:29 2011


----------

Uninstall ancient Acronis:


Code:
tifsfilt tifsfilt.sys Wed Aug 29 08:37:29 2007
timntr timntr.sys Wed Aug 29 08:38:23 2007


-----------

Update from manufacturer:


Code:
pgeffect pgeffect.sys Mon Jun 22 05:00:11 2009


---------

Visit Intel to let it scan to update storage drivers:


Code:
iaStor iaStor.sys Thu Jun 04 21:53:40 2009


---------

Update Realtek HD Audio:


Code:
RTKVHD64 RTKVHD64.sys Tue Jul 28 09:00:05 2009


Realtek

-------
Others needing update:


Code:
tdcmdpst tdcmdpst.sys Thu Jul 30 04:39:35 2009
TVALZ_O TVALZ_O.SYS Mon Jul ... Read more

Read other 3 answers
RELEVANCY SCORE 104

I am using lenovo G580-20150.
I know this problem have been opened a tread but the problem i dont' think it's same so i woud like to ask for some solution after listening to my problem.
I have been user of windows 8 and 8.1 for quite some time.
everything works fine for me for the windows that i currently using , windows 8.1.
including i can put in sleep and wake it as usual.
but ! since past few days i notice that my computer getting weird when i enter sleep mode (for example closing the lid)
it crash... it bsod.

And it occur since the day after i installed somekind of VPN software and wiFI sharing that my friend gave me.
After that day, i can't put my computer into sleep. whenever i do that it keep crash.

at first , i thought lenovo energy management that cause the prob
so i uninstalled... it still makes no different , still i can't put my computer to sleep.
after that i uninstalled the vpn and wifi sharing software, it still makes no different.
But i am very sure that the vpn and wifi sharing software cause the problem.

Because before this everything works fine until that two software comes to my computer. I really need someone that able to analysis the dmp file. TQ

I willing to learn and contribute if i were given the opportunity . tq

A:Driver Power State Failure after enter sleep mode

Hi Eric & Welcome to the forums ^_^,

I have analysed your dump files and below has been provided an analysis of the same for informative purposes :-

Code:
0: kd> !irp ffffe00175b29e10
Irp is active with 3 stacks 2 is current (= 0xffffe00175b29f28)
No Mdl: No System Buffer: Thread 00000000: Irp stack trace.
cmd flg cl Device File Completion-Context
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
>[ 16, 2] 0 e1 ffffe00177cc0050 00000000 fffff8025f7952d8-ffffe00173c59d60 Success Error Cancel pending
\Driver\tunnel nt!PopRequestCompletion
Args: 00015600 00000001 00000004 00000003
[ 0, 0] 0 0 00000000 00000000 00000000-ffffe00173c59d60
Args: 00000000 00000000 00000000 00000000


Now, as we can see from the Dump file analysis, "tunnel.sys" has been blamed which is the Microsoft's Tunneling Driver but since it is a component of Windows, chance of it being the culprit is extremely low. This means your guess that the BSOD are caused by the VPN Software.

On checking the Drivers, I found the SoftEther VPN installed on your system. Please uninstall it from the system and see if the system still BSOD's or not.

Let me know how it goes ^_^.

Read other 3 answers
RELEVANCY SCORE 104

Laptop Sony Vaio Model VPCCW1Z4E
OS Windows 7 Home Premium Service pack 1
Processor Intel Core DUO P7450.
Norton 360 V5.2.1.3, security software

Laptop starts up and can shuts down with out any problem.
If try to hibernation or standby, it take long time accessing disc then crashes. The problem only started when upgraded to service pack 1.

All drivers have been update using driver dating utility by WinZip.

Dump files & system health check report is attached.

Will appreciate any help or suggestion in resolving this issue.

Thank you.

A:Power State Driver Failure on putting PC to Sleep or Hibernation

Two issues

1-Virtally all of these were sysRelated to NETwNv64.sys Wireless WiFi Link Driver from Intel Corporation causing pci.sys to crash. I would re-install with newest driver available.
2-Your Symantec. I would remove and replace with Microsoft Security Essentials.

Symantec is a frequent cause of BSOD's. I would remove and replace it with Microsoft Security Essentials AT LEAST TO TEST
http://us.norton.com/support/kb/web_...080710133834EN

Microsoft Security Essentials - Free Antivirus for Windows

Read other 1 answers
RELEVANCY SCORE 104

I'm having a BSOD problem. After walking computer from sleep mode, within 1-2 minutes it will get a BSOD with the "driver power state failure" error and restart, but interestingly I never get the error the moment I wake up the computer. I'm using a Lenovo IdeaPad Y510P with Windows 8.1 64-bit. I already tried uninstalling the Intel HD 4000 driver, restarting computer, and installing the one on Lenovo's site (as this was suggested on the Lenovo forum as a common fix) but it didn't help. The problem only started occurring after one of the following:
- Updating Malwarebytes to latest last week
- Installing a Windows update last week (there were 3 installed components, 1 of them was an Intel HD 4000 driver update, forgot what the other 2 were)
- Updating GeForce Experience and latest NVIDIA Graphics Driver (337.88), it included NVIDIA PhysX System Software 9.13.1220
Here is a log created by WinDbg tool: 'BSOD dump' | TextUploader.com
Here is a log created by BluescreenView:
==================================================
Dump File : 060514-96281-01.dmp
Crash Time : 6/5/2014 7:23:39 PM
Bug Check String : DRIVER_POWER_STATE_FAILURE
Bug Check Code : 0x0000009f
Parameter 1 : 00000000`00000003
Parameter 2 : ffffe001`218f88e0
Parameter 3 : ffffd000`bff2b930
Parameter 4 : ffffe001`2561d1c0
Caused By Driver : ntoskrnl.exe
Caused By Address : ntoskrnl.exe+153fa0
File Description :
Product Name :
Company :
File Version :
Processor : x64
Crash Address : ntoskrnl.exe+153f... Read more

A:Driver power state failure after resuming from sleep mode

Hi Lan1 and welcome to the forums ^_^,

I have analyzed your Dump file and below has been provided an analysis of your dump file for informative purposes :-

Code:
2: kd> !analyze -v*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
DRIVER_POWER_STATE_FAILURE (9f)
A driver has failed to complete a power IRP within a specific time.
Arguments:
Arg1: 0000000000000003, A device object has been blocking an Irp for too long a time
Arg2: ffffe00135b5c060, Physical Device Object of the stack
Arg3: ffffd000c3df9930, nt!TRIAGE_9F_POWER on Win7 and higher, otherwise the Functional Device Object of the stack
Arg4: ffffe0013217d880, The blocked IRP
Debugging Details:
------------------


DRVPOWERSTATE_SUBCODE: 3
DRIVER_OBJECT: ffffe00135b70c30
IMAGE_NAME: usbccgp.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 52678625
MODULE_NAME: usbccgp
FAULTING_MODULE: fffff80157d82000 usbccgp
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
CURRENT_IRQL: 2
ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre
STACK_TEXT:
ffffd000`c3df98f8 fffff801`31803c1e : 00... Read more

Read other 7 answers
RELEVANCY SCORE 103.2

Hi,

Every time I try to put put my laptop to sleep, hibernate, restart it or shutdown, it stalls for about 10 minutes before giving me a Driver Power State Failure.

Having installed "WhoCrashed" and "Windbg", I was able to determine it was related to "ntkrnlmp.exe", "ndis.sys", "raspppoe.sys" and a vpn driver at one point or another. I "believe" I managed to uninstall the offending vpn driver but of course still overall have the same issue.

This appeared to occur while trying to do a windows update last week but I can't be sure. I presume, there is a out of date or corrupt driver but just can't seem to determine which one.

Many thanks in advance,

Hob

A:Driver Power State Failure on Sleep, Hibernate, Restart or Shutdown

Please remove / disable items from the startup in taskmanager
These programs could interfere with the boot process giving you trouble and increase the boot time.
Daemon tools, Alcohol 120% and Power Archiver Pro uses SCSI Pass Through Direct (SPTD), which is a well known cause for BSOD's.
Please remove Daemon Tools and run the SPTD pass through remover.

Uninstall Daemon ToolsDownload the SPTD standalone installer and follow these steps:
Double click the executable to open itClick on the button shown below

If the button is grayed out, like in the image, there is no more SPTD installation on your system, and you can close the window

   Warning
Programs that claim to update your drivers install either the wrong or corrupted drivers.
If you have installed any driver with Driver Booster 3, please remove them as it may cause trouble.
ONLY install the drivers from your manufacturer!

Please remove your VPN software.

Code:
*** WARNING: Unable to verify timestamp for tap0901.sys
*** ERROR: Module load completed but symbols could not be loaded for tap0901.sys

Read other 0 answers
RELEVANCY SCORE 100.8

When I go to open my laptop back up everything comes on but the home screen won't come on. The fans run, LED backlight and keyboard comes on. I have to turn the laptop off by holding the power button then it all comes up. EDIT: I have went through the Lenovo Service Bridge and checked for updates and the only thing that wasn't updated was the solutions center so it looks like everything is up to date.Also I threw in the driver power state failure so I didn't have to open another thread. That has been going on for some time while I'm doing things and I'm not sure what to do. 

Read other answers
RELEVANCY SCORE 100.8

When I go to open my laptop back up everything comes on but the home screen won't come on. The fans run, LED backlight and keyboard comes on. I have to turn the laptop off by holding the power button then it all comes up. EDIT: I have went through the Lenovo Service Bridge and checked for updates and the only thing that wasn't updated was the solutions center so it looks like everything is up to date.Also I threw in the driver power state failure so I didn't have to open another thread. That has been going on for some time while I'm doing things and I'm not sure what to do. 

Read other answers
RELEVANCY SCORE 100.4

Hi,

I've been browsing the site and the internet for a sollution to my problem, but can't seem te find it. There are similar postings, but they're always just a little different. So that's why i posted the new thread.

Since a couple of days i've been experiencing troubles shutting down my PC and using my USB ports. It started when i tried to log onto my work from home. It failed and the IT guy from work told me to reinstall citrix reciever. So I did and I was able to work from home. After finishing and logging out (to get back to my own PC) I found that my USB portst didn't work anymore. I tried rebooting, but af 10 minutes of "shutting down" I got a blue screen: Driver Power State Failure with code 1000009f.

I did the following:
- tried system restore - it failed with different time stamps
- update drivers - they were all up to date the system said
- Malware Bytes, CC Cleaner, MS Essentials, Hitman pro - Did them all, had some minor stuff, fixed that, problem remained.
- SFC/scannow - no problems
- Memory check - no problems

As it is now, the only update I have left is the update to WIN10. However it has tried and failed during a few of the reboots, so that doesn't seem to be and option.

After try all different kinds of things from a lot of posts I decided to refresh my windows install. Did a lot of updating and still the problem remains. Although I now found out that USB devices that are plugged in upon startup work. Once I unplug en replug them, t... Read more

A:BSOD Driver power state failure when shutting down /failure USBports

Are you still having BSOD problem?

Read other 1 answers
RELEVANCY SCORE 100

So I have a pirated windows 8.1 which I have been using for more than a year now. Since the past one week my drivers ( especially the internet driver) keeps crashing and stops detecting any networks. Upon an attempted restart I get the Bsod for which I have attached the files ( All the minidumps.) I run a Dell 5521 R and have updated the drivers, uninstalled and reinstalled them too. Kindly help ASAP as I require my wifi urgently tomorrow.
Note: After restart the drivers get refreshed automatically and start working for sometime. And then the same issue. Please help.VATSAL-Tue_02_09_2016_101910_61.zip

Read other answers
RELEVANCY SCORE 98

A couple days ago I did a force shutdown while my computer was mid shutdown, corrupting some windows files (I thought I smelt my computer burning so did a panic shutdown, but it was something else burning)

initially windows would not boot from my ssd, it would go all black with green artifacts on the screen just before the welcome screen, but I still had another windows install on my old HDD so I just booted from that without issue. I then ran the windows repair from install disc and it fixed the windows install on my SSD.

Since then, however; when I leave my computer unattended for a while I get a BSOD on returning with the driver state failure message. I'm not sure if this is occurring on sleep/hibernation or on reboot from the windows update I was trying to do.

Your guys' help is much appreciated, thanks!

update: did a reboot, no issue. Tried to put the computer to sleep, another BSOD.
uploaded a new SF rar file, as well as the debug tool zip file

A:BSOD driver power state failure

Hi Strini.

First of all, make it sure that the SSD is running with the latest firmware.
How to Upgrade Samsung SSD Firmware | StorageReview.com - Storage Reviews

Also update the BIOS to version F10b dated 2012/08/31 (not to the latest one) if possible. The newer BIOS and SSD firmware is most needed to run a SSD properly.

Get rid of intel rapid storage. First uninstall it from Control Panel > Programs and Features. Then Uninstall the driver from device manager.
Right click on "my computer" icon and click "manage" on the context menu.
It will open the "computer management" window.
Select "Device Manager" in the left pane, It will list all the existing devices up.
Expand "IDE ATA/ATAPI controllers" by clicking on the triangle in front of it.
Select one Intel device item under it, right click, uninstall.
Continue the process for all Intel items under "IDE ATA/ATAPI controllers"
Now restart the computer. At restart, windows will auto configure the appropriate native system driver.
Install the NVIDIA DRIVERS 314.22WHQL only.
Uninstall All nvidia items in Control Panel > Programs and features3D Vision Control Driver
3D Vision Driver
Graphics Driver
HD Audio Driver
PhysX
nvidia Update
(Are you using nvidia chipset drivers? If so, dont uninstall anything other than those are listed).
Now follow Drivers - Clean Left over Files after Uninstalling
Download 314.22 WHQL. While installing, Select Custom (Advanced) in... Read more

Read other 5 answers
RELEVANCY SCORE 98

Hi, my computer is being shutdown a few times with the Blue Screen and I have no idea what's going on. I have the Windows 7 and suposedly I have no hardware problem and/or compatibility but I have been reading the posts and I don't know what to do. So I have uploaded the DUMP files so you guys can give me a help. What should I do???

A:Driver power state Failure BSoD

Hi,

The timestamp on the driver that is causing the crash (nvm62x64.sys) is Sat Oct 18 10:01:06 2008 which is far to old for a Windows 7 system. Try updating the drivers, you should find them here (look for your motherboard chipset): http://www.nvidia.co.uk/Download/index.aspx?lang=en-uk

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa80039b5a20, fffff80000b9c518, fffffa800785f700}

*** WARNING: Unable to verify timestamp for nvm62x64.sys
*** ERROR: Module load completed but symbols could not be loaded for nvm62x64.sys
Probably caused by : nvm62x64.sys

Followup: MachineOwner
---------

0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

DRIVER_... Read more

Read other 4 answers
RELEVANCY SCORE 98

I have an ASUS S56CM laptop with Windows 8.1.

For the past few days I have been getting a BSOD (Driver Power State Failure) upon start up. Leading up to this, my computer would freeze completely at random times not that often and I had to do a hard shut down to fix it.

The past three days have been identical. When turning my computer on from a completlely off state, it takes forever to start then eventually gives me the BSOD. The 0% thing never loads so I do a hard shut down and turn the computer back on. It still takes forever to start (8 minutes +) but I don't get a BSOD and am able to use the computer fine. Then when shutting down, it takes over 6-8 minutes as well. Before all this, my computer would get to the log in screen in under one minute.

I had a program called "WhoCrashed" but it hasn't logged any of the BSOD's from startup, only ones that I had when the computer was already on. For one of them, it told me the error may have been caused by iastora.sys which was the Intel Rapid Storage Technology driver. I tried to delete this as well as installing a newer version but it didn't fix anything.

A:BSOD Driver Power State Failure

Sorry for the delay in responding. There just aren't that many people who do BSOD analysis, so at times we get a bit overwhelmed!
Add to that the release of the Win10 preview and my system messing up - and I'm way behind on replying to topics. Sorry!

Do your still need help with this problem?
I will be notified if you reply to this topic and will respond within 48 hours.

Read other 8 answers
RELEVANCY SCORE 98

Hello,

I have a BSOD problem that states Driver Power State Failure. I read it is caused by a problem with a change in the alimentation mode or something, but this BSOD really happens randomly (last time occurred while I was reading a web page... I didn't even touch a key or the mouse).

I'm running Windows 7 32bits, my laptop is 3 or 4 months old (windows 7 was already installed).

I tried to run the batch from the "Blue Screen of Death (BSOD) Posting Instructions", but no folder is created when it's done... I followed every step (also ran the batch as an admin) so I don't know where the problem is coming from. The batch runs smoothly until the end, but there is just no folder created in my Documents folder. (I don't know if this is normal, but on the line right after "We will begin in 5 seconds..." there is a message saying that "the path hasn't been found" (my os is in french, so I don't know exactly what is the original line in english) but the batch still runs to the end).

I attached my last 3 minidumps, the perfmon file and a msinfo32.nfo file.

Thanks in advance for your help!

A:BSOD Driver Power State Failure

Please follow these instructions --> http://www.techsupportforum.com/f217...ns-452654.html

Read other 9 answers
RELEVANCY SCORE 98

I am getting the bsod error driver power state failure. It appears to be random unless i go to play star wars the old republic and it does it with in about 10 minutes of playing every time. This is fairly recent. I was playing it before for several hours with out trouble, and now it does it outside of the game. I hope you can help. Attachment 312126

Attachment 312127

A:BSOD Driver Power State Failure

Hi punkiemi.

How many days ago you installed Service Pack 1? Very recently it seems?

The zip contains two crash dumps. One, the older one is related to games. And, this time the PC was not SP1 installed.

Code:
BugCheck 116, {fffffa80066fb010, fffff8800517e664, ffffffffc000000d, 3}

Unable to load image \SystemRoot\system32\DRIVERS\nvlddmkm.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
Probably caused by : nvlddmkm.sys ( nvlddmkm+97e664 )

Followup: MachineOwner
---------
Taking the age of your PC into consideration, stop 0x116 BSODs may occur under certain conditions.

Is the computer hot? Report us the heat of the computer after a couple of hours of your normal usage. Upload a screenshot of the summery tab of Speccy. Alternatively, you can publish a Speccy snapshot too: Speccy - Publish Snapshot of your System Specs .

The PC seems to be overclocked.

Code:
Max Speed 2300MHz
Current Speed 2310MHz
As you are getting BSODs, you should stop overclocking and run all the hardware components like CPU, GPU and RAM to their default settings.

Check if the Power Supply Unit (PSU) supplying adequate power to the computer or not.
eXtreme Power Supply Calculator
Also let us know the the wattage of the PSU.

Stress test the Graphics Card using Furmark.
Video Card - Stress Test with Furmark

Install the NVIDIA DRI... Read more

Read other 1 answers
RELEVANCY SCORE 98

Hello,

I've been getting these BSODs and the error says it's caused by the ntsokrnl.exe. Below are the details of my laptop and I've attached the required reports. Any help is appreciated.

Thank you!

ASUS Laptop model K53E-BR5

- Windows 7
- x64
- OEM
- Age of system: 8 months old
- Age of OS: 8 months old

- CPU: Intel i3-2310M
- Video card: Integrated Intel HD Graphics 3000 video
- Motherboard: Not sure about the motherboard, this is an Asus Laptop with the Bios version: American Megatrends Inc. K53E.216

A:BSOD - Driver Power State Failure

Hi -

What is plugged into USB ports?

Code:
Args: 00000000 00000000 00000000 00000000
>[ 16, 2] 0 e1 fffffa800714f060 00000000 fffff80002ed07f0-fffffa80029c1220 Success Error Cancel pending
\Driver\usbhub nt!IopUnloadSafeCompletion
Args: 00016600 00000001 00000001 00000006
[ 16, 2] 0 e1 fffffa800700da00 00000000 fffff80002ed07f0-fffffa800ca43120 Success Error Cancel pending
\Driver\usbccgp nt!IopUnloadSafeCompletion
Args: 00016600 00000001 00000001 00000006
[ 0, 0] 0 0 00000000 00000000 00000000-fffffa800280a790
Run - http://www.techsupportforum.com/foru...ed-473665.html


Regards. . .

jcgriff2


`


BSOD SUMMARY

Code:
Loading Dump File [C:\Users\PalmDesert\_jcgriff2_\dbug\__Kernel__\041312-15771-01.dmp]
Built by: 7601.17790.amd64fre.win7sp1_gdr.120305-1505
Debug session time: Fri Apr 13 16:28:36.571 2012 (GMT-4)
System Uptime: 0 days 1:10:36.554
Probably caused by : usbhub.sys
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
FAILURE_BUCKET_ID: X64_0x9F_IMAGE_usbhub.sys
Bugcheck code 0000009F
Arguments 00000000`00000003 fffffa80`0714f060 fffff800`00b9c3d8 fffffa80`0521f860
??????????????????????????????????????????????????????????????????????????????????????``
Loading Dump File [C:\Users\PalmDesert\_jcgriff2_\dbug\__Kernel__\040812-19172-01.dmp]
Built by: 7601.17727.amd64fre.win7sp1_gdr.111118-2330
Debug session time: Sun Apr 8 23:24:59.031 2012... Read more

Read other 10 answers
RELEVANCY SCORE 98

i am having an issue with bsod's it says driver power state failure and crashes
i tried to upload the minidump files but it says i dont have permission to access these files but i am logged in as the administrator please help
 

A:BSOD driver power state failure

What OS are you running?
 

Read other 1 answers
RELEVANCY SCORE 98

Hello guys,

I have seen lot of topics with the same subject as I have, but as I understand each of them is "special", so I am posting new one.

Sometimes when I restart / shut down my computer, it is turning off for few minutes (10 - 20m) and then I can see BSOD.
Last one was with Driver Power State Failure message - 011510-17128-01.zip minidump.
I have also few more minidumps - Minidump.zip (but I think almost all are with the same message)
I don?t know how to read it, so please, can someone check it and help me?

I have Acer Aspire 3694, Win7

Thank you very much for help

A:Driver Power State Failure BSOD

Most probably this is due to your Deterministic Network Enhancer Miniport or Cisco Systems VPN Client (dne2000.sys). Also, please note that the dne2000.sys file is listed below as being older. Also, this could be due to the other, network related drivers in the list below.

Please:
- download a new copy of the Win7 drivers for the Cisco VPN Client device
- uninstall the current copy from your system.
- install the freshly downloaded copy
- wait for further BSOD's.

Also, Please update or remove these older drivers that were loaded at the time of the crash. Don't use Windows Update or the Update drivers function of Device Manager. Please use the following instructions to locate the most current drivers:





Quote:
How To Find Updated Drivers:
- search Google for the name of the driver
- compare the Google results with what's installed on your system to figure out which device/program it belongs to
- visit the web site of the manufacturer of the hardware/program to get the latest drivers (DON'T use Windows Update or the Update driver function of Device Manager).
- if there are difficulties in locating them, post back with questions and someone will try and help you locate the appropriate program.


- some driver links are on this page: http://www.carrona.org/drvrdown.html

Here's the older drivers:

Code:
bcm4sbxp.sys Tue Nov 21 07:25:43 2006 - Broadcom 440x 10/100 Integrated Controller XP Driver by Broadcom Corporation (Broadcom.com - Home).
CVP... Read more

Read other 3 answers
RELEVANCY SCORE 98

Hi, my computer is being shutdown a few times with the Blue Screen and I have no idea what's going on. I have the Windows 7 and suposedly I have no hardware problem and/or compatibility but I have been reading the posts and I don't know what to do. So I have uploaded the DUMP files so you guys can give me a help. What should I do???

A:Driver Power State Failure BSOD

  
Quote: Originally Posted by wolfinhu


Hi, my computer is being shutdown a few times with the Blue Screen and I have no idea what's going on. I have the Windows 7 and suposedly I have no hardware problem and/or compatibility but I have been reading the posts and I don't know what to do. So I have uploaded the DUMP files so you guys can give me a help. What should I do???



These crashes were probably caused by your nvidia network driver nvmf6264.sys

I would download and install a fresh copy
I would also run a system file check
(to do that type cmd in search>right click and run as admin>sfc /scannow) note the space between sfc and "/")

Let us know if you need help with this

Ken

Read other 2 answers
RELEVANCY SCORE 98

Current OS
? Windows 7 Home Premium
? 64-bit

? What was original installed OS on system?
Windows Vista Home Premium 64-bit.

? OEM version (came pre-installed on system) or full retail version?
OEM Version.

? Age of system
7-8 Months.

? Age of OS installation
Windows 7 just installed, but i had this problem previously with Vista.

? CPU
Intel i7 920

? Video Card
Nvidia GTX 285

? MotherBoard
Not sure.

? Power Supply - brand & wattage
Not sure.

Thank you for your time. :)

A:BSOD driver power state failure

Hi -

The bugcheck on the lone mini kernel dump -

0x9f (0x6,,,) = driver in an inconsistant state of power; the power transition timed out waiting to synchronize with the Pnp

The first driver was named the probable cause of the BSOD. They all need to be updated -
[/font] [/code]

Code:

RTSTOR64.SYS Tue Dec 02 01:01:40 2008 (4934CF44) - Realtek USB 2.0 Card Reader

e1y60x64.sys Mon Aug 18 17:45:05 2008 (48A9ED61) - Intel(R) 82567LF-2 Gigabit Network Connection
gwfilt64.sys Thu Apr 10 04:20:29 2008 (47FDCDCD) - Realtek HD audio
SCDEmu.SYS Tue Aug 07 11:19:48 2007 (46B88D94) - PowerISO Computing, Inc.

Realtek HD Audio --> http://www.realtek.com.tw/DOWNLOADS/...&GetDown=false

Realtek USB card reader drivers --> http://www.realtek.com.tw/downloads/...&GetDown=false

Intel Intel(R) 82567LF-2 Gigabit Network Connection --> http://www.intel.com/support/etherne.../cs-029669.htm

Power ISO - see system manufacturer's web site.

Un-install Daemon Tools/ Alcohol 120. The driver common to each has caused many BSODs in Windows 7 systems.

Regards. . .

jcgriff2

.




Windows 7 x64 - Bugcheck 0x9f (0x6,,,)

Code:

Opened log file 'C:\Users\PalmDesert7\_jcgriff2_\dbug\__Kernel__\_99-dbug.txt'

Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.


Loading ... Read more

Read other 6 answers
RELEVANCY SCORE 98

I have attached the files has requested.

I am having varying instances of Driver Power State failures as indicated by the BSOD This only happens when using the internet and I cant figure out which file is causing the shutdown.

Also interesting: I use my computer for home recording with an M-Audio interface, Blue Snowball Microphone, and Alesis M1Active 320USB studio monitors.
While recording or playing back in the Studio SONAR7, the program seems to just randomly start working at half speed and getting all jumpy. I will stop it rewind a bit and start it again and it is fine for a bit and then will start doing it again. Any Ideas on this? could this be linked to the same problem that is giving me the BSOD?

A:BSOD Driver Power State Failure

  
Quote: Originally Posted by Kurt301


I have attached the files has requested.

I am having varying instances of Driver Power State failures as indicated by the BSOD This only happens when using the internet and I cant figure out which file is causing the shutdown.

Also interesting: I use my computer for home recording with an M-Audio interface, Blue Snowball Microphone, and Alesis M1Active 320USB studio monitors.
While recording or playing back in the Studio SONAR7, the program seems to just randomly start working at half speed and getting all jumpy. I will stop it rewind a bit and start it again and it is fine for a bit and then will start doing it again. Any Ideas on this? could this be linked to the same problem that is giving me the BSOD?



Hi Kurt and Welcome

These were all virtually identical and caused by your mausb.sys driver. M-Audio Fast Track Pro PNP Device ID USB\VID_0763&PID_2012\5&BD40FB&0&4 Driver c:\windows\system32\drivers\mausb.sys

I would remove it to test.


Code:

Microsoft (R) Windows Debugger Version 6.11.0001.404 X86
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Users\JMH\Desktop\Windows_NT6_BSOD_jcgriff2\050911-36909-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

DbsSplayTreeRangeMap::Add: ignoring zero-sized range at ?ffffffff`82b5fad4?
Symbol search path is: SRV*C:\Symbols*http://msdl.microsoft.com/download/symbol... Read more

Read other 3 answers
RELEVANCY SCORE 98

Just started happening within last 2 days.

Gateway P7811FX laptop (approx 2yrs old), full retail Win7 Pro x86 installed early June 2011. Never had a BSOD until last couple days. Both crashes occurred seemingly at random (not at startup).

Ran verifier as instructed here and OS crashed at startup. Able to turn off Driver Verifier in Safe Mode. Restarted normally to collect dump and perfmon files.

TIA

A:BSOD Driver Power State Failure

A device driver is probably the cause
For that reason old drivers should be updated:

Synaptic Touchpad driver Drivers | Synaptics
SD reader driver Fujitsu Gateway Support - Downloads & Support Documents
Conexant modem driver(s) Gateway Support - Downloads & Support Documents
Marvel Yukon Network driver Marvell - Support


Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

DRIVER_POWER_STATE_FAILURE (9f)
A driver is causing an inconsistent power state.
Arguments:
Arg1: 00000003, A device object has been blocking an Irp for too long a time
Arg2: 87bff2d8, Physical Device Object of the stack
Arg3: 82b2cae0, Functional Device Object of the stack
Arg4: 85e51ef8, The blocked IRP

Debugging Details:
------------------
DRVPOWERSTATE_SUBCODE: 3

IRP_ADDRESS: 85e51ef8

DEVICE_OBJECT: 87999510

DRIVER_OBJECT: 85dc24b0

IMAGE_NAME: disk.sys

DEBUG_FLR_IMAGE_TIMESTAMP: 4a5bbf20

MODULE_NAME: disk

FAULTING_MODULE: 8b218000 disk

CUSTOMER_CRASH_COUNT: 1

DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT

BUGCHECK_STR: 0x9F

PROCESS_NAME: System

CURRENT_IRQL: 2

LAST_CONTROL_TRANSFER: from 82acbf35 to 82ae3f2c

STACK_TEXT:
8... Read more

Read other 5 answers
RELEVANCY SCORE 98

Hello, I am having random BSOD crashes mostly when browsing on internet.

My Build is
- x64
- Original OEM
- > 1 month old
- > 1 month old, never reinstalled.

Any help is more than welcome.

A:Driver State Power Failure BSOD

Hello and Welcome !

Seems like lot of issues are going on. First thing i noticed is sptd.sys duplex driver which i well known for BSOD. I would recommend to uninstall it follow this article DuplexSecure - FAQ

Also it looks to me like it's an issue with AiCharger.sys - an Asus program named AiCharger (may also be a part of the Asus AISuite or ASUS Ai Charger). Then uninstall the current copy of the program and install the freshly downloaded copy.

Run a Hardware Diagnostic (Memory and Hard Drive) follow this link for instructions Hardware Diagnostic !! ? Captain Debugger

Bugcheck:

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa80083a1060, fffff8000460e518, fffffa80060214c0}

Probably caused by : ntkrnlmp.exe ( nt! ?? ::FNODOBFM::`string'+292b0 )

Followup: MachineOwner
---------

0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *... Read more

Read other 8 answers
RELEVANCY SCORE 98

Hi. Every time I shut down, I'm getting the good old BSOD with the message DRIVER POWER STATE FAILURE. I attach TSF_Vista_Support.zip containing TSF_Vista_Support files and PERFMON.html. System spec below...

Windows 7 Home Premium 32-bit
Previous OS - Windows Vista
System is 8 months old, 4 months since Windows 7 installation
1.4Ghz Intel Core2 Solo
Motherboard: Acer Aspire 4810T Base Board Version
3GB RAM
Controller: Intel(R) ICH9M-E/M SATA AHCI Controller
Display: Mobile Intel(R) 4 Series Express Chipset Family

I hope that covers everything. Any help would be much appreciated as I have no idea what is going on! Many thanks in advance

A:BSOD Driver Power State Failure Win 7

Hello and Welcome to TSF,

From what you are stating here - Do have any external USB devices attached to the computer? were they attached when you reinstalled another operating system?

Read other 4 answers
RELEVANCY SCORE 98

My laptop has been having issues with sleep, hibernate, shutdown, etc... On all of these functions it shuts down the graphics, turns off the speakers and wifi, and then just hangs without shutting down. Every now and then it will work properly for a few days and then go back to giving me grief.

The BSOD error is relatively new, maybe for the last two to three weeks. I've only noticed it when the computer is trying to go into sleep mode.

I have attached the results of the Sf Diagnostic Tool.

Thank you in advance for your help.

A:BSOD Driver Power State Failure

Bump

Read other 1 answers
RELEVANCY SCORE 98

OS - Windows 7 pro x64 - In place upgrade (since November 2009)

original installed OS - Vista Business x64 - OEM

System is 1 year and 3 months old

CPU - Intel Core 2 Quad Q6600 @ 2.40GHz

Video Card - Nvidia Geforce 9500 GT (1GB)

Motherboard - Asus - IBIBL - LB (benicia)

power supply - Coolmax M-500B - 500watts

The past week I noticed that every time I put my computer to sleep, I would notice that my monitor would either stay on or I'm assuming after a short while come back on while the rest of the computer was sleeping. My monitor by the way is a Samsung Syncmaster 2232BW plus. I noticed this monitor staying on problem at least 3 times this week. So today, I left my computer on, and when it tried to automatically enter sleep mode, a stop error occurred. This is the first time that I got this blue screen as the computer tried to enter sleep mode. Other system information that might be useful: I have a wireless mouse and keyboard, both logitech and both are operating with setpoint. I also have a Creative SB X-Fi sound card installed. Furthermore, shortly before this post I went to device manager and updated the driver for my videocard.

A:Driver Power State failure BSOD

Hi -

The bugcheck on the single dump file -

0x9f (0x4,,,) = driver is causing an inconstant power state - it is not able to sync with the PnP subsystem. The default NT Kernel named as probable cause.

I believe it to be a combination of NIC + Norton Internet Security.

Your D-Link DWA-556 Xtreme N PCIe Desktop Adapter driver must be updated - too old for Windows 7 -

Code:

jswpslwfx.sys Mon Apr 28 19:59:25 2008 (481664DD)

However, there are NO Windows 7 drivers listed for it and the April 2008 Vista driver appears to be the most recent available.

D-link Support DWA-556 --> http://www.dlink.com/products/?pid=DWA-556&tab=3

If you cannot locate an updated driver, the device will need to be replaced.

Remove NIS/ N360 from your system -

Download the Norton Removal Tool (NRT); save to desktop. Boot into SAFEMODE - NO Networking. Tap F8 key during boot-up. Go to desktop, RIGHT-click on the NRT icon and select Run as Administrator. When complete - re-boot.

NRT - ftp://ftp.symantec.com/public/englis...moval_Tool.exe

Reset the Windows Firewall to its default settings -
START | type firewall.cpl | select firewall.cpl above under programs | top-left, select "Restore Defaults"

Install MS Security Essentials --> http://www.microsoft.com/Security_Essentials/

Regards. . .

jcgriff2

.

Windows 7 RTM x64 -- BSOD Bugcheck 0x9f (0x4,,,)

Code:
Opened log file 'C:\Users\PalmDesert7\_jcgriff2_\dbug\__Kernel__\_... Read more

Read other 2 answers
RELEVANCY SCORE 98

Hello at all.

Sometimes when i try to shut down my compuer, it hangs for a little bit and than i get a bsod with the driver power state failure 0x9F.

This is not every time but randomly.

I hope anyone can help!!!

? OS -Windows 7
? x64
? What was original installed OS on system? Windows 7 x64
? Full retail
? Age of system (hardware)- 1 year
? Age of OS installation - have you re-installed the OS? one year, never re installed

? CPU - intel i5 [email protected] 3,4GHz
? Video Card - Nvidia GTX 680
? MotherBoard - Asus P8Z77-V LX
? Power Supply - BeQuiet & 750w

A:BSOD driver power state failure

Hi, and welcome to TSF.

Please navigate to c:\windows\minidump, zip up any minidumps you find and attach to your next post.

I'm not sure what the analysts do in cases like this but the BSOD.zip that you attached contains your perfmon report but its in German. Anything you can do about that from your end?

Read other 6 answers