Over 1 million tech questions and answers.

Help configuring my home network.

Q: Help configuring my home network.

I have very little knowledge of networking. I have had configured my home network with the help of online guides and tutorial and mainly by hit and trial, last year and it performed successfully. It may not be perfect but it worked and this is how it has been working.

Setup1.
ADSLModem provided by ISP (PPOE 192.168.1.1 and subnet mask (255.255.255.0) DHCP enabled range (192.168.1.50 to 192.168.80) and default DNS by ISP. UPNP enabled (but nothing configured here and in NAT as well, as things were working fine so I never touched it) Wireless (OFF)
NOTE, I can't tell if my ISP registers Mac of this modem to authenticate the services)

Setup2
LinksysWTRG router with DDWRT 2.4 installed with auto 'configuration DHCP' (guess this enables connections from the SETUP1 for WAN, hence IP 192.168.1.50), subnet mask 255.255.255.0, gateway 192.168.1.1 and DNS 192.168.1.1. LAN setup; ip 192.168.2.1
Subnet 255.255.255.0, gateway 192.168.1.1. DNS by UnblockUs.com to access Hulu, Netflix etc outside U.S. NAT services and UPNP enabled with nothing specifically mentioned to forward the services to.
Wireless enabled. And DHCP Server enabled for LAN IP 192.168.2.100 to 192.168.2.130.

Setup3
16 port switch that is hosting Roku, Bravia LCD, 2 NAS and a windows seven Laptop wired. All the devices on the switch are connected to Setup 2 through wire and wireless, like iPhone, iPads etc.

Setup4
TpLinkRouter set on Dynamic Ip configuration with auto Ip for wan and 192.168.2.20 for LAN. With subnet 255.255.255.0. And DNS auto. Devices connected to this are PS3, WDTvLive and Windows 7 64 bit a Ultimate desktop and a couple of iPhones and an ipad.
Windows seven is hosting Plex media server, and utorrent like softwares and PS3 is obviously for online.
Please note I have always recived 'NAT' problem while playing online but speed has never become a problem. Plex media server hooked with Setup4 always connects to NAS on Setup3.
This way I have been able to watch any of my media at any corner of house on wire and wireless.

This whole setup worked pretty good for more than a year and now I am feeling bad that I broke it just to make Plex media server accessible to me on my trips to other cities. I read the articles from Plex support and encountered that I had a 'Double Nat' problem and thought I could fix it by trying to make a little changes. It's been three days and I am getting frustrated. Nothing is working. Good thing I have back up of all the router settings. But I want to fix this once for all.. If everything still fails by Sunday I am going back to my old setup and compromise accessing my media server outside my network. Huh.

Now the Setup looked like this
Setup1 [from LAN] to Setup2 [to WAN] to Setup3 [Switch connecting all the devices of Setup3] and ---> to Setup4 ( Tplink Router(Cat5 or 6 from switch to LAN port) this router is at different floor) to all the devices of setup four.

What I am trying to do is turn Setup1 into a basic modem that will only handle internet connection without any DHCP, firewall and UPNP Nat leaving these for router at Setup2 to handle. It should have been pretty simple. Isn't it ?
I seriously think I am making some mistake in assigning IPs and Subnets. Want to keep the IPs assigned already from the setups above. I also didn't and don't want to change how everything is connected through either net on assigned ports.
Or must I ?

I am guessing my problem lies in Subnets. Because each time I assign an ip or subnet on any modem or router one thing or other stops responding. By responding I mean they stop seeing see each other. Please let me know if this is the way. Help me fix this and if you think I am getting it all wrong please advise another method.
Please note I cannot go all wireless due to some reason.

Let me know if left out any other details.
Ciao.

Read other answers
RELEVANCY SCORE 200
Preferred Solution: Help configuring my home network.

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

RELEVANCY SCORE 65.6

Hi, hope someone can help!

I have a network card given to me by a friend. I need to install it in my pc which is simple enough.

However, how do I configure it once its physically in the pc? Also, does XP Home have generic network card drivers as I dont know what make the card is so have no idea of the drivers required.

Thanks in anticipation.

A:XP Home and configuring a network card

I'm using D-Link and Linksys cards in my PC's.
IIRC, D-Link for instance, specifically states to keep Windows out of the install process and to use the provided D-Link software.

I think you'll have better luck if you can get ahold of the software/drivers that came with the card.
If the CD is lost then I would go to the manufacturer's site and see what's available to D/L.

JF

Read other 1 answers
RELEVANCY SCORE 65.2

Hello. My question is almost identical to Tanna's -- except perhaps for the details of my goofy system. Should we discuss here or should I start a new thread?

I have an ancient desktop (Pentium III 500 running Win98SE), attached to my wireless router (Westell 327W) attached to my DSL service. Just bought a lovely new laptop (running XP). The laptop's wireless connection is hitting the DSL flawlessly (which I sure don't want to screw up) but I'd love to know what I need to set up in order to network the two computers as well.

Just like Tanna, I'd like to, from the laptop, access the desktop's printer and scanner, as well as transfer files amongst the drives in both computers.

Do I need a separate wireless card for the desktop, or can I already do this through its ethernet card? Will I have any problems unique to the XP & 98SE coexistence? Etc. Etc.

Thanks in advance for any help, as I'm "old at" computers, but new at networking!

-- Randy
 

A:Solved: Configuring Wireless Home Network

Read other 9 answers
RELEVANCY SCORE 65.2

I have a desktop computer that is connected to my ADSL modem and printer, and it is also connected to a wireless router. My laptop computer, which has wireless, can connect to the Internet using the desktop's ADSL modem and router without any problem, but I would also like to be able to print from the laptop, as well as share files between the desktop computer and laptop.

How can I do this? Can someone please post some detailed instructions?
 

A:Solved: Configuring A Wireless Home Network

Read other 10 answers
RELEVANCY SCORE 64.4

Although this post isn't strictly related to an issue on my computer, perhaps it can still be addressed as it deals with the general security of a network. The physical setup of the network (which does provide for fully functional internet access) is as follows in terms of wire connectivity:

The wireless router is connected via an ethernet cable on its WAN port to a LAN port on a wired firewall. This wired firewall is connected to the modem via ethernet from WAN to WAN.

This configuration as previously stated provides for internet access. My question however, is if the external IP address on the wireless router is protected by the built-in security features of the wired firewall (once having enabled them in the firewall's web-based utility), or if the firewall is simply acting as a switch, in that it successfully relays the connection from the modem to the router without implementing its security features in the process.

If it is the latter, then I ask how to configure this setup so that the wireless router utilizes the firewall's security features properly.
 

A:configuring home network with firewall and wireless router

Read other 10 answers
RELEVANCY SCORE 62.8

Hello.

I am having difficulty getting my HP Officejet Pro 8500(A910) configured to save digital faxes to my Iomega 2TB Home Media Sever (cloud edition). My home network is setup through a Linksys E4200.

I was able to successfully configure it to save to a folder on my PC, but I do not want to leave it running 24/7.

I believe the breakdown is in the Authentication part of the setup... It asks for the Windows username and password, which works fine for the PC setup but not for anywhere else. Do I use the UN & PW for the home media server if I'm saving to one of its folders? If so, how do I correctly type the path? It is communicating with the folder and leaving an alphanumeric file saved inside the folder when I use the 'save and test' option, but it breaks down from there.

I've spent nearly 6 hours on the ph with HP tech support and engineers, but they do not have a resolution.

Does anyone here have a suggestion?
 

A:Configuring digital fax to network folder located on a home media server

You should investigate how communication goes between HP and your PC, NBT (port 445) or Netbios (139). After investigate how do you communicate with Iomega. Most often those home servers are linux based, what means it can have samba server inside.

How you see folders of this home server? I believe in both ways path should look like \\device_or_PC_ipaddress\sharename in same way you saved now faxes to your PC... same way to show path, only IP address will be different
 

Read other 1 answers
RELEVANCY SCORE 51.2

Hi. I have no more ideas on what to try next. Any help greatly appreciated.My laptop is running Windows 7 Professional 32bit and is fully patched. The Ethernet adapter (Marvell Yukon 88E8055) is enabled and the wireless adapter (Intel PRO/Wireless 3945ABG) disabled (via software and the hardware switch). Symantec Endpoint Protection provides AV/security (via group policy). It is highly likely the problem was self inflicted and not caused by a virus / malware.I use the cisco VPN client and wanted to upgrade it (a reinstall may have been sufficient but as I was going to the bother I thought I would upgrade) as I was having some annoying timeouts when using the client immediately after logging into my desktop.I started by removing the existing (old version 5.0.05.0290). During the removal the screen went black and the laptop was not responding; ie I couldnt get the screen to wake up. I ended up powering off by holding the power button for 5 secs. On reboot, it appeared that the old vpnclient (5.0.05.0290) had been removed and everything else was functioning as normal. So I tried to install the new version (5.0.07.0410).The vpn setup program gets as far as "Installing Network Components" and produces error "Error 27854. The network configuration lock is held by another application. Close all applications and run Setup again. If this message re-appears after closing all applications, reboot then re-try the install (the application holding the install lock may... Read more

Read other answers
RELEVANCY SCORE 50.8

i have windows 7 and i installed virtual box (ubuntu) to do this.

i want to have two linux gateways and those two machines should either have the same NAT or public routable ip address.
basically i want to install openswan and configure the ipsec. in order to do this i need two linux gateways.

can anyone guide me how to setup two linux gateways to do this??
 

Read other answers
RELEVANCY SCORE 50

My Windows Explorer is totally collapsed when opened and I cannot discover how to set it up the way I would like it to open (like with my computer and the C: drive expanded and ready to go).

What am I missing?
 

A:Configuring Win Explorer in XP Home

Read other 6 answers
RELEVANCY SCORE 48.4

I have two computers at home: a desktop pc that has a cable modem, wireless router and a printer connected via parallel cable; and a laptop with integrated wireless. The desktop has a vpn so that my wife can connect to her office in PA. I would like to share the printer if I can so I don't also have to connect the printer to my laptop. I have tried to enable printer sharing but to no avail. Any suggestions out there?

DJ
 

A:Configuring a home pc with wireless router for printer sharing

I noticed you said you enabled printer sharing but did you actually go to the printer properties and share the actual printer?
 

Read other 6 answers
RELEVANCY SCORE 48.4

Hi, I want to configure win7 Home Premium to get it's updates from a WSUS server, but there is no gpedit.msc. How do I achieve this..

Thanks..

A:Configuring windows 7 Home Premium for WSUS Updates

  
Quote: Originally Posted by bugzee


Hi, I want to configure win7 Home Premium to get it's updates from a WSUS server, but there is no gpedit.msc. How do I achieve this..

Thanks..


There is no gpedit.msc in Home,it is only in Proffesional and Ultimate

Read other 9 answers
RELEVANCY SCORE 48.4

I'm in the process of putting together a fairly powerful machine intended for video work. I've got two 4TB HDDs and a 1TB Ultra M.2 SSD. The SSD is the C: drive; the HDDs are partitioned as K:, L:, and M: with another partition reserved for a dual-boot Ubuntu Linux install.

I've just installed Windows 10 Pro (last night) and I was starting to install software when I stopped short. I want to avoid writing to the SSD as much as possible, so I'd like to configure the Users folder for program data and documents on one of the HDD partitions. Also, if what is now a home-based business ever goes anywhere, I may eventually have employees using this machine. How should I configure it now, while it's fresh, to put as much of the user data as possible on the spindle HDDs and also to segregate user data to protect potentially sensitive information as much as practical?

Tech Support Guy System Info Utility version 1.0.0.4
OS Version: Microsoft Windows 10 Pro, 64 bit
Processor: AMD Ryzen 7 1700 Eight-Core Processor, AMD64 Family 23 Model 1 Stepping 1
Processor Count: 16
RAM: 32720 Mb
Graphics Card: NVIDIA GeForce GTX 1050, -2048 Mb
Hard Drives: C: 931 GB (888 GB Free); K: 2047 GB (2047 GB Free); L: 2456 GB (2456 GB Free); M: 1269 GB (1269 GB Free);
Motherboard: ASRock, AB350 Gaming K4
Antivirus: Windows Defender, Disabled [Note: I have Comodo Antivirus Pro intalled and activated; it's not showing up on this utility.]
 

Read other answers
RELEVANCY SCORE 48

Hi guys, this is my first post, ok i have in my house a little home network, but i can't share files. I have tried to configure all this pc's with the wizard of Windows XP, but isn't not work. All PC's has the same Group, in no one pc i can't see the resources of the others PC in the network, please help me, I need share files.

I have designed a diagram with specifications in Microsoft Visio: Check the Attached files.

Someone with experience in network to configure it without the wizard of Windows "Set up a home or small office network"???'.

Any suggestion is good.

Email

 

A:Configuring this Network

Read other 10 answers
RELEVANCY SCORE 48

Hi.
I am trying to set up a network. The operating systems are windows 98.I can't get them to see each other on the network.
Do you have to manually setup IP addresses or leave it as "obtain IP addresses automatically"
I've Networked XP machines using the network wizard and that worked perfect, but 98 seems more difficult.
Is there any web page on networking that would help me configure the network properly?
 

A:Configuring a Network

Read other 7 answers
RELEVANCY SCORE 47.6

ok right to it: I have a 3g usb modem that i use to connect to the internet. That connection is shared to my wlan connection that connects to my ddwrt router which is used for home networking and internet sharing.. It would look something like this:

INTERNET <3G> PC <WiFi> ROUTER <WiFi> OTHER DEVICES

My problem is that i have trouble accessing the admin area of my router at 192.168.1.1 when my 3g internet is connected or accesing the internet when i can access the admin area ( depending which connection is on top of the list in advanced network settings -> adapter and bindings). What do you think would be the easiest way to solve this and to setup 3g internet sharing most efficiently?

My PC is the one in specs running windows 8 pro, the usb 3g modem is huawei e353, router gigaset sx763 running ddwrt.
 

A:Configuring 3G USB Modem and router for internet sharing and home networking.

Read other 7 answers
RELEVANCY SCORE 47.6

Hello, I need some help. I think I may have messed up some folder access permissions between my two user accounts on my laptop. I have two user accounts: Owner & Personal
Owner is being used for everything, while Personal is now being used for gaming/torrenting.
My father likes to use my computer fairly often now and I dont want him to be able to snoop around all my folders on both accounts. Both accounts are adminstrators and are password protected. I tried to change permissions myself and messed some things up. Now my Owner user account cannot access the Personal user folder. It says access denied and to see the security tab of the folder. Can anyone help me fix what happened and try and do what I was wanting to do. I have seen it set up on one of my friends computers how he was able to lock his user folders but still access them from opposing user accounts via entering the password when it was prompted, similar to inputing the password into UAC window when you want to change things.....

Thanks for the help!!!!
 

A:Solved: Need help configuring Folder Permissions on Windows 7 Home Premium

This guide will show you how to password protect individual folders: http://www.simplehelp.net/2010/11/29/how-to-create-a-password-protected-folder-in-windows-7/

General set up of file permissions can be easily found by Googling.
 

Read other 3 answers
RELEVANCY SCORE 47.6

Hi All,
Problem is the Vista Machine connecting to the shared HPG85xi AIO on the network.
I am working on installing a Vista Home Premium Gateway PC on an existing network that consists of a 98 machine, two XP home PC's and an XP home laptop.
With the exception of the laptop, all PC's are connected via ethernet cabling to a Linksys WRT54G sharing cable internet access.
One of the XP home machines and the 98 are connected to a Dlink switch which is wired to the Linksys router. This XP home machine has the HP connected locally and shared.
All PC's have printer and file sharing enabled. All PC's are in the same workgroup, all PC's can see and share files bidirectionally. Including the Vista machine. All PC's with the exception of the Vista machine can connect and print to the HP.
When you try to connect the Vista to the HP, and it doesn't matter how (using Network and connect, using Printers to add a printer, using add a Printer to set up a new network printer and entering the path...whatever), the error message is "Access is Denied" before you can even install the drivers.
I used my IBM laptop running XP Pro to serve the HP via the USB connection (same as how the XP Home PC is doing it), the Vista can connect and print no problem; so it would seem there is an issue with the access rights in the XP Home PC sharing the HP.
I also tested the Vista PC on another network that runs XP Pro and it connected and printed with NO issues.
I trie... Read more

A:Solved: Vista Home Network Printer Issues, XP Home Network

Read other 16 answers
RELEVANCY SCORE 47.2

Hi,

First of all, my computer is the main gateway for access to the internet and I have one other computer which uses my internet and is locally networked with my computer. The other computer's IP address ranges between 192.168.0.2 and 192.168.0.255.

I just installed ZoneAlarm Security Suite and when I first ran it, it asked me to allow a network and I added it into the internet zone. It had the IP address as 192.168.0.0, so I assumed this was the local network. But even though I allowed this, the other computer can't connect to my network nor get internet access from my computer. I have also checked the 'This computer is an ICS gateway' option, yet the network still doesn't seem to work and I also have an IP range between 192.168.0.0 and 192.168.0.255 in the internet zones section of the firewall.

I also have Windows Live Messenger at Super Trusted Level, yet it still doesn't connect...

Could someone please tell me why it doesn't work?

Thanks for your help.
 

A:ZoneAlarm: Configuring Network

bump
 

Read other 2 answers
RELEVANCY SCORE 47.2

what would be the best settings for my network card ? The reason i ask is i read somewhere(i forget where) that Configuring this will help in online games ping and lag wise. Thanks

windows xp sp1
cable modem
netgear fa310tx erthernet

If you need to know something else please post
 

A:Configuring my Network Card

Download an app called Cablenut, or go to http://www.dslreports.com/ and run their tweak test. They also have a couple of tools there that might be of interest to you, such as Dr TCP. The tweak test will give you some recommendations for changing your settings if needed. Cablenut will do similar though it will give you the option of applying the settings for you.
 

Read other 7 answers
RELEVANCY SCORE 47.2

Me and my friend have just bought two network adapters, hoping we can connect our two Pc's together.But we don't really know how to do this.Should we make one Pc to be a Server and the second one to be a Client?
If that's the case, how do we do it?
If not, what are the other options?
Thank you!!!
 

A:Configuring the Network Adapters

Moving this to the Networking forum. Please go there to look for replies.

Also, please take a look around that forum - I'm pretty sure they walked someone through a network set up a month or two ago.

------------------
Get free stuff and help out a poor computer tech
Don't forget the amazon.com GCs waiting for you - just listen to music while online!

http://www.rkfdcore.com/ebaypics/referrals.htm
 

Read other 1 answers
RELEVANCY SCORE 47.2

Anyone know a website that tell u how to configure your network card to work properly? If not can someone explain what i need to configure in my contorl/network or network neighborhood/properties.

Thanks,
 

A:Configuring network card..

o yeah BTW i have DSL, Windows 98 Plus...
 

Read other 2 answers
RELEVANCY SCORE 47.2

Hi, I set up connection to 2 of my pc's through a wired connection to my router. How do I set up the PC portion of it so I have a network? Both pc's are using windows 10 pro. I havent done this since windows 98 so its been a while. Any positive help is appreciated.

thx
 

A:configuring a wired network

If you have two (or more) devices connected to the same router they are already on the same network.

With Windows 10 then you can try to use a Homegroup or you can enable file and printer sharing. I think that enabling file and printer sharing is similar to the following (I can check later if this doesn't work) ...

Short description for Windows 7 and 8/8.1 file and printer sharing:

Go into the Network and Sharing Center from the Control Panel or from the Network icon in the Notification Area. Your network must be designated 'Private' (or 'Home' or 'Work'). Click on Change advanced sharing settings. In the Private or Home or Work section you can configure File and printer sharing, Public folder sharing, and Password protected sharing.

You may want to change the Workgroup name. To check it or change it right click on "Computer" and select "Properties."

You must uninstall or properly configure any non-windows firewall (security suite).
 

Read other 1 answers
RELEVANCY SCORE 47.2

Im trying to get the most out of my upload speed that i can.
I'm a frequent Skype user and i can get a good quality coming from the person im talking to, but my voice tends to cut off and become distorted for the other person receiving it
i ran a speed test and my results were
6.15Mb/s download
.33Mb/s upload

its not great i know, but its the best my isp has to offer for my area
but .33Mb/s upload should be more than enough for me to send a high quality voice call
i have already set QOS to make Skype a top priority, im not sure if that has any
effect on upload

is there anything i can/should change to help?
someone recommended i use tcp optimizer, but others said i shouldnt try that with windows 7

any help will be appreciated

A:configuring network for skype

If you are downloading/uploading something it will be good to cancel that. Also what's that .33Mb/s?
I have this connection,and don't have any problems with skype even when I'm downloading torrent
I think that upload speed is not real,but should be over to 5-6.

Read other 6 answers
RELEVANCY SCORE 47.2

Hi,

On a previous post I had been told that after setting up the home network I would need to configure any 3rd party firewalls manually.

I have norton internet security on the desktop and was able to do it with no problem.

But on the laptop I now have Zonealarm and can't seem to find how to allow my desktop on the firewall in order to be able to file and printer share.

Any help would be appreciated.

Thanks
 

A:Configuring ZoneAlarm for Network

Read other 16 answers
RELEVANCY SCORE 47.2

I have DSL from Bellsouth and I have a block of static ips. These ip are used to all most fo my machines to gain access to the outside world.

I want to be able to set up a second router with privatly assigned IP's 192.168.x.x to work with my wireless system. I woud like them to be DHCP assigned.

Here is the kicker I want to use the Bellsouth Statics to give Internet access to the private IP's but I am not sure on where to look for this information or how to start.
I have a Netopia Modem/Router combo handling the STatic Ip's
I have a Linksys WRT54G handling the DHCP addresses

I thought bu configuring the Linksys router to have a Static IP address from Bellsouth would work but then again it didn't and I am here.

Any help will be appreaciated
 

A:Network Configuring 2 Routers

Read other 12 answers
RELEVANCY SCORE 47.2

Dear Users,
I want to configure two network cards in windows 2003 standard edition.
One of my lan card is connected to my local lan and other to the internet, The Pc acts as a proxy .

when i am accessing my local intranet, the site is searched in MSN ( internet), i want to access both intranet and internet.

please suggest a solution,.
 

A:Configuring Two network cards

Install two cards
Install RRAS on the server
Configure RRAS
You would also need "proxy" software

Cheers!
Scully
 

Read other 1 answers
RELEVANCY SCORE 47.2

Okay, I have a small home network using a D-Link wireless router.

I have 3 boxes, 1 - WinXP, 2-WinServer2003, 3-WinServer2003

Right now they are setup and share an internet connection but that is about it.

box1 is my main PC for games and work and has a USB printer haooked to it.
box2 is my webserver
box3 will eventually be my webcrawler/email server

What I want to know is, can the 3 boxes share the 1 USB printer?
Also I would like to configure the network so all 3 boxes can access a shared network folder for passing files back and forth.

I am not a network guru by no means, it took me a while to get my current setup so any guidence is very appreciated, also the more 'dummy proof' the better.

So if anyone can tell me how to acheive this setup or point to some articles that can I would be very grateful.

Thanks,
 

A:Configuring Windows network

Enable/Disable Windows File & Printer Sharing:

http://compnetworking.about.com/od/windowsfilesharing/ht/enable_disable.htm
 

Read other 2 answers
RELEVANCY SCORE 47.2

Hello,

I have a problem. I have a linksys Wirless 4-port router and a linksys wireless USB adapter (WUSB11 version 2.6). That is what I'm trying to get working on my desktop. I also have a laptop that my boss let me borrow to get me working at home with the desktop. The laptop has a YDI wireless card and it is reading the router's signal just fine and it's working and everything... so my laptop is working. I know I'm getting the signal. And so I'm pretty sure that the problem isn't hardware. The laptop has XP and the desktop has 98SE. The WUSB11 software on my desktop is reading both the router signal and the internet link I have, but it says "You are connected to the access point, but the Internet cannot be found". I am supposed to go to http://198.162.1.1 to configure the router on my desktop, as I can on my laptop, but it will not let me reach that site. It just says that the server cannot be found. Is there anyway you guys can help me? I would really like to get this problem fixed... I've been without Internet at my house for about a month and it's starting to really bother me.

Thank you very much in advance,
David Wilder
 

A:Help me with configuring linksys network please.

The correct ip you should connect to is 192.168.1.1
not 198.162.1.1
Let's start there....... This should be your default gateway as well.
 

Read other 1 answers
RELEVANCY SCORE 47.2

Ok.. so here is the situation...

I get Wireless internet from my service provider, (they send out a wireless signal and my computer picks up on it and uses it with its WAN card).

What I want to do is use my wireless router to get the signal, and then send the internet via LAN cable to my 2 PC's. Does anyone have any idea of how I go about doing this? And what is the best way to set up the Wireless Router???

(Here is an overview of what I Wish to accomplish

Wireless Internet Signal
.{
..{ (wireless signal)
(WIRELESS ROUTER)
|
| LAN HARD WIRE
.|________pc2
.|_________pc 1
 

A:Need Help Configuring Wireless Network

Read other 9 answers
RELEVANCY SCORE 47.2

I have a D Link 624 router connected to my computer that's running windows XP SP2.
I had the network up and running for about 6 months with no problems. I had to go away for about a week and when I came back it wouldn't connect to the internet anymore. I ran the ethernet cable directly from the dsl modem to the computer and couldn't connect that way either. I called verizon and they had me type in 192.168.1.1 and the helped me through the setup process and I was back online. I still can't get the network to work though. After hooking the network back up I typed in 192.168.0.1 for the D Link configuration page. At login I typed in admin and left the password blank as instructed. The configuratin page won't load. The login screen just keeps coming back. I probably shouldn't have touched the reset button on the router but I did.
I went to the D Link support page and tried different things with no luck.
Any suggestions?????

Thanks
wgc19136
 

A:problem configuring network

Read other 9 answers
RELEVANCY SCORE 46.8

After exhaustively trying to configure my Canon Printer that is connected to my network through the USB port on my
Airport Extreme I have given up. I have an Imac connected to the network and the printer works just fine using that computer, but my PC with Windows XP cannot find the printer. The PC can find the WPA2 network through the Airport Extreme and is connected using a Linksys Wireless G card. I tried using the IP address (default gateway) of the router to configure the printer, but it still doesn't work. I have downloaded and installed the latest Canon Printer drivers. Nothing seems to work. Documents still sit in the printer queue ready to be printed and the PC cannot find the printer. Please help?!
 

A:Configuring Network Canon Printer

See here:
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh1770.html
 

Read other 1 answers
RELEVANCY SCORE 46.8

The complexity/messiness of my office network is getting out of hand and I'm planning to rip it out and start from scratch. I've got about 35 wired devices spread over 8 rooms, plus a couple on wifi. Internet is from a BT fibre and a BT business hub. At the moment a single router port goes into a 16 port gigabit switch, which then runs off to other switches in different rooms. I've also got a couple of machines acting as file servers.

I've got an accounts department that has a lot of heavy traffic internally, so I need to make sure that their internal traffic doesn't slow down the network as a whole. But they still need to also access the same shared files as everyone else.

Also, it would be great to support a guest wifi login, that allows internet access, but doesn't allow access to other devices on the network.

So, to configure:
Should I run all wired devices back to a single 48 port switch? Or run to a separate switch for each room?
Should I use 4 separate switches, one for each pair of rooms, each running into one the router's ports? (Would this allow greater concurrency?)
How would I separate the accounts department's heavy traffic from the rest of the building's network traffic, while still allowing file sharing?

Thanks
 

A:Configuring a wired office network

Do you have a closet or central location where you can locate all the IT equipment?

Personally, I would identify a closet/room to have house the IT equipment. Spend the money to have drops installed in the wall in the various rooms and then have all the cabling pulled back to this central closet/room and terminated into a patch panel. This would necessitate at a minimum a wall rack installed. At each location where you want a network drop installed, I would have at least two Ethernet jacks per drop.

I would use a single 48 port switch that has stacking capability. If you out grow the number of ports on the 48 port switch, you can add another switch to the 48 port you have now and have it act like one big switch.

Guest WiFi isn't a problem with a business class access point. I would look into products from Aerohive, Ubiquiti, Aruba Networks, or Meraki. These devices have a captive portal feature much like what you see in hotel settings.

As far as the account department's heavy traffic, what do you mean heavy traffic? What type of protocol/traffic are we talking about here? Your network doesn't appear to pose a large strain on any current switch. Other than isolating the accounting department for possible network usage, is there any other reason why you would want to isolate their equipment from the rest of the corporate network?
 

Read other 2 answers
RELEVANCY SCORE 46.8

All-
Everyone in our home has a personal laptop and our desktop is used any more. I wonder how I can configure the laptops to backup to the desk top. We use Windows7 on the laptops and XP on the desktop...
I need to know how to configure everything so everything backs up to the desktop. Any idears????

Thanks in advance

Lenny

A:Configuring XP as a Back-up for Network Computers

The easy way - setup network share for each user on the "backup computer" - map a drive for each person to the share - and then use your back up software on the "backup computer" daily

POINT: they must save their files to the share for them to get backed up.

I will let someone else do the hard one.

Read other 10 answers
RELEVANCY SCORE 46.8

Hey all -- I'll try to be concise.

In the House, there is Spectrum internet which should be about 200 Mbps wired. There is a router and an access point. In the house there are several devices, both wired and wireless. Both types of connection approach 200 Mbps (for wireless, this is assuming you are within a reasonable radius of the AP). So far, so good.

But -- I live in the Apartment about 80-100 ft away, up a bit in elevation as well as on the second floor. There is something like a 10ft differential between our flat and the room in the House.

To get internet in our Apartment, I have an EnGenius ENH202 (which advertises speeds up to 300 Mbps) configured as an AP w/static IP blasting towards our window from the House. It is behind a window, so the signal must pass through two windows currently.

Internet access via EnGenius is both unstable and slow. I understand speeds will fall off, but I cannot get above 20 Mbps on any device and usually range from 7-13. As to stability, the internet drops out often, EnGenius disappears from list of WiFi network access points, etc. Interestingly, sometimes we can connect to the Spectrum 2G network more easily and reliably than EnGenius, though not always and not for long. EDIT: For example, the speed test just had EnGenius at 16 Mbps and Spectrum 2G at 33 (sudden, new high). I could handle the lower-than-advertised speeds (probably user error, I know), but the instability is killer.

- I am not particularly confident that I have... Read more

Read other answers
RELEVANCY SCORE 46.8

i just brought a belkin 802.11g that runs 54mbps, but we i got it to work it, but it displays 11.0 mbps... it;s download speed is only 20k. how do i configure it properly?

btw my router is alos belkin 802.11g but it;s in my basement and my computer is two floors up....(might be a factor). I also heard that by installing sp2 it will make wireless connection run faster, is it true?

specs
p4 3.2
9800xt
512ram
120gb
asus p4c00-e dlx
 

A:configuring wireless network adaptor

Read other 8 answers
RELEVANCY SCORE 46.8

Hi , I am desperate to get some info on exactly what I need to configure my BROTHER MFC-210C printer to my existing home wireless network which uses a NETGEAR DG834G Wireless Modem Router ,the BROTHER NC-2200W wireless USB printer server which their website recommends for this job is no longer available ,so what can i use instead ???
(I need it quickly !!!) cheers Iain

A:configuring existing usb printer to network

You can try investigating here;

http://welcome.solutions.brother.com...=English&dlid=

edit: there may be some value in this article;

http://www.microsoft.com/windowsxp/u...utt_july2.mspx

Read other 1 answers
RELEVANCY SCORE 46.8

Hello, I've been searching all over for help with a problem I'm having and stumbled across this forum - really hope someone can help me!

I've just had a leased line installed to provide me with a high speed internet connection. It's a 100Mbps fibre pipe and am trying to integrate it with my existing network of 6 PCs and a printer. Previously, I had a 2 line bonded ADSL connection using a Comtrend 5631 router, which also acted as a DHCP server, allocating IPs for all the machines.

The hardware that has been installed with the new line is a Cisco 1941 router which is managed remotely, I have been provided with 5 IP addresses and it operates on a subnet of 255.255.255.248. My original network runs on 255.255.255.0, with the router as 192.168.1.1. What I want to do if possible is use my Comtrend router (or purchase a new one if I have to) the same way it has been used before, i.e. as the main hub which allocates the network addresses but have it connect to the internet via the new router (as the ADSL will soon be disconnected), so that all the machines are connected to the fibre line at high speed. How do I do this?

Thanks so much in advance

Oliver.
 

A:Configuring my network with the new fiber line

It sounds like what you will need to do is use the router in a "passive" mode. What i mean is simply keep your internal network as it is, but create a static route towards the new Cisco Router. The static route should probably be 0.0.0.0 with a subnet mask of 0.0.0.0. What this means is that anything destined to a destination the current router is unaware of, it passes it to the Cisco router which will then forward this onto the internet.

Does this make sense?
 

Read other 3 answers
RELEVANCY SCORE 46.8

I am trying to set up a multi-site network (5 sites total), and need some basic assistance. I can configure the routers and such, but need to know if the following scenario is correct before I start the configuration:

There are 4 sites that all need to connect to a main site, and for redundancy, to at least 2 of the other sites.

There are 3 class C IP address ranges available (we'll say 200.200.100.x, 200.200.101.x and 200.200.102.x)

The main location will have a web server, so I want to set up a DMZ at this site.

I'm thinking I can configure each of the routers with Frame Relay using a Class C address for each router's "WAN" side, and anything on the "LAN" side of each of these routers (and the switches, servers, workstations) can use a private 10.x.x.x IP range.

Does this make sense? Each of the sites would need to connect to the main site for authentication (ie. no DC's in the satellite offices, only in the main office).

If I have to use the Class C ranges for the entire network, can I use the 100.x range for routers/switches/firewalls, the 101.x range for servers, and the 102.x range for workstations? I'm sure I would need to configure a VLAN to make this option work, correct?

Thanks in advance!
 

A:Configuring multi-site network

Hi&#8230;

I&#8217;m uncertain if you are still working on this or if this is still a relevant thread. I guess if you don&#8217;t need the help anymore, could you mark the thread as solved?

As to your questions&#8230;..

Let&#8217;s start with the basics 1st. You will not and cannot (used loosely) break down your routers, switches, and servers in the method you described. There are &#8220;NO&#8221; written rules that prohibit you from configuring your network IP&#8217;s in anyway you want to configure them. However, there are recommendations and guidelines that you would want to try to use where possible.

At the same time, if you use a service provider for certain services, they may require your servers, printers, and so forth to be in certain range. Such as, they may want all of your servers to be in the lower IP range, reserving let&#8217;s say the 1st 20 IP&#8217;s for servers, routers, switches, and so on.

So, you can do as you wish, but save yourself some serious headaches, you should keep your &#8220;locations&#8221; at the very least all within the same IP blocks. What class you use is up to you and your company. So, by IP Blocks, I mean you should keep let&#8217;s say site #1 all on a 10.71.13.xx range. I recommend and many others that you plan your network to a &#8220;T&#8221;. I prefer to keep main routers and servers in the lower numbers such as 10.71.13.1 thru 10.71.13.20. Of course, if you have tons o... Read more

Read other 1 answers
RELEVANCY SCORE 46.8

Okay so to start off the configuration at my office was DSL modem-wireless router-switch- 6 computers.
One computer could connect to the internet and the rest couldn't however every computer could get to one another over the network. We got a new DSL modem that has the wireless router built in. I disconnected the old wireless router and modem and connected the new modem/router combo. Now the one computer that could get to the internet can no longer do so unless I go in and auto configure for IP and DNS. This poses a problem because when I do so that computer can no longer connect to any other computer on the network. What do I need to do to straighten this out? We would like to still only have that one machine connect to the internet. I could have all the machines on the network auto configure but then they would all be able to connect to the internet, right? Thanks in advance for any help it is appreciated.
 

A:Solved: help configuring network at office.

The easiest solution might be to change the router's LAN address to match the previous router/existing static IP address assignments already set on all the PC's and then re-setup the static IP on the one that needs to access the internet correctly(as previously set).

I assume what is happening is that the new router is handing out addresses in a different range which doesn't correspond to the addresses already set on all the PC's. I also assume you are preventing internet access on the rest of the PC's by not entering DNS or Gateway addresses?

An alternate method, and there's actually several, is to enable filtering on the router to prevent internet access, most routers have some form of access control or internet restriction options these days. In that scenario you could switch to automatic IP assignments.
 

Read other 3 answers
RELEVANCY SCORE 46.8

I would like to confirm that the settings I have are correct for a second managed switch I am adding to my network. DHCP I have disabled, IP address I have found one on the network unused (192.168.1.xxx), subnet mask is 255.255.255.0. The only thing I'm not sure about is the default gateway setting - what should this be?

A:Configuring second managed switch on network

Default gateway should be the LAN IP address of the router you use to go to the Net, IE the one connected to your modem and or LAN IP address of a Modem/Router combo box.

But if you are disabling the DHCP server in a managed switch you are basically turning that managed switch into a dumb switch just like any other. Well not like any other Dumb switch.

Read other 3 answers
RELEVANCY SCORE 46.8

I downloaded Kai xlink. Dont know if you know what it is but it helps get a game online.I downloaed it and my internate connection goes away and then it is lost. I go to "view wireless connections" and it says windows it not running you wireless network settings. What ever program thaat is running it run that program. I uninstalled Kai think it was it and it was. I dont know why it is running my network settings but then I had to go and make windows run it. I have never heard of someone having this problem with this. Any help would be great.
 

Read other answers
RELEVANCY SCORE 46.4

Me and my friend have just bought two network adapters, hoping we can connect our two Pc's together.But we don't really know how to do this.Should we make one Pc to be a Server and the second one to be a Client?
If that's the case, how do we do it?
If not, what are the other options?
Thank you!!!
 

A:{Advice Offered} - Configuring the Network Adapters

Moving this to the Networking forum. Please go there to look for replies.

Also, please take a look around that forum - I'm pretty sure they walked someone through a network set up a month or two ago.

------------------
Get free stuff and help out a poor computer tech
Don't forget the amazon.com GCs waiting for you - just listen to music while online!

http://www.rkfdcore.com/ebaypics/referrals.htm
 

Read other 2 answers
RELEVANCY SCORE 46.4

Hi everyone,

I have a small lan of around 10 computers in my office which are connected through a switch
connected to a airtel broadband connection. I want to configure a network server so that
i could manage an control the internet traffic used by all the workstations in the lan through that server. All the workstations have either WinXP or Windows 7 on it.

I havnt purchased a server. I want to use a desktop(having some good configuration) as my network server.

Can anyone help me step by step of how top proceed to achieve this. I know its a very long procedure and its not that simple. But any help would be appreciated.

Thanks in Advance.
Deepak Madan
 

Read other answers
RELEVANCY SCORE 46

Hey all,

I'm using a Thinkpad T22 with a Linksys WPC54G Wireless Adapter, trying to create a bridge between it and my Ethernet adapter (Intel Pro/100 SP Mobile Combo Adapter) in Windows XP Pro with SP2. These are my only two network connections, and every time I try to bridge them, I get an error saying "An unexpected error occured while configuring the network bridge."

I've looked all over the place, trying to find an answer, but haven't found anything. Neither connections are set as my ICS connection. I have also tried this:

http://cheatppc.blogspot.com/2008/07/unexpected-error-has-occured-while.html

but Windows didn't rebuild the WMI repository, and anyway I just reinstalled Windows a few days ago.

I also looked at this: http://support.microsoft.com/kb/309640
which is not the problem I'm experiencing.

I am out of ideas. Help?
 

A:An Unexpected error occured while configuring the network bridge.

Read other 15 answers
RELEVANCY SCORE 46

I am doing an overhaul of my home network, in particular related to safe external connections and safe sharing.

There is no conn issues or alike, I am only looking for an opinion regarding how to connect to my home network from an external computer, and tips regarding safe configuration.

As it is I have one Radmin license which should be a pretty safe way to connect but I am, currently, also able to use RDP protocol.
The obvious advantage with RDP is that I can use any W7 computer. Even my phone,

I have two Windows 2008 based servers, one WHS and one Standard. I was thinking of letting the Standard act as a Gateway and thus removing direct external access to the WHS, I assume that would increase security, but I am not sure of how to configure the Standard server securely. Or if I could use another software than Radmin and RDP to connect.

Tips? Thoughts? Questions?

A:Safest way to VPN to network? Configuring Server 2008 as Gateway...?

Hi Coram,

if you are concerned about security, the safest way of protecting your network is adding a Security Appliance like Sonicwall. You may use VPN or Remote Desktop Services (RDS), either one will be fine but again having a very secured network is beneficial. I am a big fan of Sonicwall.

Hope this helps.

Read other 7 answers
RELEVANCY SCORE 46

Hi,

Please assist me in configuring File & Printer sharing network between my Desktop (XP Pro) & Laptop (Vista Home Premium 32bit); connected to internet through WiFi ADSL2+Modem.

Done the intial setup. Named my desktop as 'OfficeDesktop' & my latop as 'SonyVaio'. Now I am able to view my laptop in my desktop network & vice-e-versa.

The issues am facing is:
1) In OfficeDesktop (XP Pro);
I am able to access only the PUBLIC folder but others are coming 'Access Denied'.

2) In SonyVaio (Vista Home Premium);
I can view OfficeDesktop, but is not accessible.
Message: "Logon failure: the user has not been granted the requested logon type at this computer."

Pls assist.

A:Help configuring File & Printer Sharing Network between XP Pro & Vista

To share files or a printer from XP computers, follow these procedures:~
1. Download and install the Link Layer Topology Discovery (LLTD) responder:~

http://www.microsoft.com/downloads/d...displaylang=en

Read the instructions!

2. Check these out as well...

Windows Technet:~

File and Printer Sharing in Windows Vista

Most Valuable Professional:~

How to share files or a folder in Vista
3. Don't forget to configure (Input ip addresses in subnetworks) your Firewall to accept sharing from other computers.If you have Kaspersky check this below:~

Kaspersky Blocks My Network

Read other 2 answers