Over 1 million tech questions and answers.

BSOD during general use, errors 0x0000003B and 0x000000BE

Q: BSOD during general use, errors 0x0000003B and 0x000000BE

Hi, I recently upgraded my system with a new graphics card and SSDs, and a new PSU. I installed windows 7 x64, and now I've had 2 BSODs within 24 hours. The first one occured while I was playing Deus Ex: Human Revolution. The error was 0x0000003B and the faulty file was dxgmms1.sys. I reinstalled the graphics drivers and it hasn't shown up anymore. Now, I was installing GTA IV and watching a video on youtube, and got another BSOD, this time with error 0x000000BE. I can't seem to isolate this problem. I've attached the files in the zip archive.

Also, i think its worth mentioning that the when I installed windows, I used a 32bit driver for the SSD RAID 0 array since windows wouldn't take the 64 bit driver because it wasnt signed(although the driver did have the signature file on the disk). After the installation finished, Windows automatically updated the RAID driver.

AMD Phenom II 1090T CPU
Gigabyte GA-870A-UD3 motherboard
EVGA GTX 690 Graphics Card
2x 90GB Kingston HyperX SSDs in RAID 0
4x 4GB Mushkin DDR 3 1066 RAM
1300W Rosewill PSU


Preferred Solution: BSOD during general use, errors 0x0000003B and 0x000000BE

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: BSOD during general use, errors 0x0000003B and 0x000000BE

Security Software: ??? I recommend the following:Download and install Malwarebytes, update it, do not start the free trial, and then run a full scan. Also run a full scan with your antivirus software installed on your system. If you do not have antivirus software installed, see the Good and Free system security combination. for better security steps and scanning tools. Make sure to update the security software before running the full scan with it.
For the new hardware, I would recommend getting the latest BIOS. Also, does your SSD hardware have its latest firmware installed?

I see you are running a RAID configuration. RAID is designed more for servers than for the home user in mind. It often results in problems with data corruption and disk related issues when used in a home computer. Further reading: Why RAID is (usually) a Terrible Idea - Puget Custom Computers

Read other 1 answers

Hi Guys,

Recently I've got these two BSOD errors on my brothers computer. They've both only happened once but from past experience I've discovered that if you get a BSOD once your probably gonna keep getting it until you resolve it. The computer's not overclocked and I haven't installed any new drivers recently and I've had this computer for about 2 years with no problems before about a month ago. This is my brother's computer so the specs listed in my profile are not for this computer. I'll post the specs for this PC below.

The two files it says are responsible are win32k.sys and nvBridge.kmd. By the second one, I'm guessing it might have something to do with the graphics card but I''m not sure. I've attached the dump files for you guys to have a look at. I would really appreciate if one of the tech savy guys here could help me with this issue. Thanks

PC Specs:

Windows 7 Professional x64
Asus Rampage III Extreme
Intel Core i7 950 3.07Ghz
3x2GB 1600Mhz Corsair Ram
2 x Nvidia GeForce GTS 450
Seasonic 850w Power Supply

A:BSOD Errors 0x00000050 & 0x0000003b

Can someone please help me with this problem.

Read other 1 answers


I've recently had a few alarming issues with my PC, the most recent ones relating to BSODs. The first BSOD was an error '0x0000003b'. According to Bluescreenview, it had something to do with my Nvidia drivers. This happened when I was running ModernWarfare 2 in the background, Skype, Google and VLC media player. This was about 2 or 3 days ago. I once again had a BSOD today. This time, it was an error '0x00000050' and had something to do with Direct X. It happened shortly after I exited Modern Warfare 2 and had Skype, Google chrome and VLC media player running. I have not tried any heavy games like BF4 or Watch Dogs recently, but they played fine a few weeks ago.
Some extra details: Very recently, a little over a week ago, I had changed a BIOS setting (disabled legacy booting) after which my PC did not turn on. It gave 3 beeps. I had removed one stick of RAM and my Graphics card, and flashed the BIOS, after which it ran fine. I decided to re-install Windows. I had lost my Windows 8 disk, so used Windows 7 instead. This fairly new installation of Windows 7 seems to be causing a problem. Also, I tried doing a Memory Diagnosis of Windows. I do not believe it found any errors. Another interesting note is that several games have crashed on my old installation of Windows 8 due to my Graphics driver not responding or some Direct X error, but it never caused any BSODs.

My specs: Intel DH61WW, 8Gb of Ram (2 sticks of 4gb Corsair memory), GTX 550Ti 1gb Inno 3D, Intel i5 230... Read more

A:Windows 7 BSOD Errors '0x0000003b' and '0x00000050'.

Hi Abul Rahman Ema.

You have two crash dumps in the uploaded zip and none of them has anything with nvidia driver.

Install Service pack 1 and all other windows updates. Otherwise the system will remain vulnerable to threats.

Windows 7 Kernel Version 7600 MP (4 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16385.amd64fre.win7_rtm.090713-1255
Learn how to install Windows 7 Service Pack 1 (SP1)
Service Pack and Update Center - Microsoft Windows

Report us back about any further BSOD after installing Service Pack 1.

BugCheck 50, {fffff900c225bcf0, 0, fffff9600032c69d, 0}
Could not read faulting driver name
Probably caused by : win32k.sys ( win32k!SFMLOGICALSURFACE::OwnsSurfaceCleanup+2d )

Followup: MachineOwner

BugCheck 3B, {c0000005, fffff960001a4283, fffff88005a6c020, 0}

Probably caused by : win32k.sys ( win32k!HmgLockEx+a3 )

Followup: MachineOwner

Read other 9 answers

Hi guys, I have been experiencing BSOD crashes for a few months now. I wasn't really sure what to do but now that they have become more frequent (normally 1-3 a day) I have come to you guys for help. I'm not completely computer illiterate and I've followed the appropriate error posting instructions. Any help is hugely appreciated, thank you.

Windows 7 Home Premium
- x64
- Windows 7 Home premium first and only OS on PC.
- Have owned the computer for about a year and a half.
- I haven't re-installed the OS at any point.

Thanks again, Nambarc.

A:BSOD generally at startup, errors: 0x0000000a and 0x0000003b.

> Avast can be a contributing cause of BSOD'S .
Please remove and replace with Microsoft Security Essentials AT LEAST TO TEST


Microsoft Security Essentials - Free Antivirus for Windows

> These crashes were caused by memory corruption/exception (probably a driver).
Please run these two tests to verify your memory and find which driver is causing the problem.

* If you are overclocking anything reset to default before running these tests.
In other words STOP!!!

* If you have raid update its Driver.


*Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. Memtest86+ - Advanced Memory Diagnostic Tool

*Boot from the CD, and leave it running for at least 5 or 6 passes.

Just remember, any time Memtest reports errors, it can be either bad RAM or a bad motherboard slot.

Test the sticks individually, and if you find a good one, test it in all slots.

Any errors are indicative of a memory problem.

If a known good stick fails in a motherboard slot it is probably the slot.

RAM - Test with Memtest86+

Driver verifier

Using Driver Verifier is an iffy proposition. Most times it'll crash and it'll tell you what the driver is. But sometimes it'll crash and won't tell you the driver. Other times it'll crash before you can log in to Windows. If you can't get to Safe Mode, then you'll have to resor... Read more

Read other 6 answers


I've recently started seeing BSODs with my gaming rig. It first happened while playing Star Wars: The Old Republic, but after that would occur during post or shortly after.

I had not added any new hardware recently, or updated any drivers. Rig had been stable since I built it 18 months ago. No overclocking.

I checked my drivers, and my graphics driver is up to date. I updated the drivers for some of my peripherals, which did not seem to help. Next I tried updating the chipset, but after that it seemed worse. I could not get past the login screen.

I then flashed my bios with the latest stable version. That got past me login (posting this on my comp).

I followed the steps to collect the previous crashes and was hoping you could look through them and identify anything I could fix. zip attached.

Thanks for your time.


A:BSOD, multiple errors 0x0000003b, 0x0000007e, 0x0000007f

Hi mattmcbride welcome to SevenForums .

Lets run a memory test . Take a look at the link below

RAM - Test with Memtest86+

If you get any errors during the test .

Take a look at Part 3: If You Have Errors: from the tutorial above .

Read other 5 answers

I've had my Samsung laptop since summer 2012, and I get random BSOD shutdowns. This has happened since I got the computer, basically. I bought it in the US and now live in Hungary and depend on it for my job, so I have not been able to send it away while under warranty.

Anyway, sometimes I get the error more than once a day. Sometimes I don't get it for a week or two. As I said, it seems completely random. More recently, if I close the laptop and put it in my bag, it will have restarted on my walk home. As the thread title says it is most often 0x0000003B, though once is a while it is something like "0x000000D5" (I have to admit I'm not 100% here).

It's frustrating problem, and I'd just resigned myself to it. I only found this forum this evening and performed the SF Diagnostic (attached). I hope this gives you enough information.

A:Random BSOD errors on year-old laptop, usually 0x0000003B

Hello jdenn81.

It is a multifold issue, but the main issue is network related. It is caused by Kaspersky, mainly. Kaspersky uses some Zone Alarm services like True Vector. And Trye Vector hijacks TCP connections; which results in ntework blockage, and causes BSOD.

fffff880`0b094770 fffff880`04bc5430Unable to load image \SystemRoot\system32\DRIVERS\vsdatant.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for vsdatant.sys
*** ERROR: Module load completed but symbols could not be loaded for vsdatant.sys
Description here: Driver Reference Table - vsdatant.sys

It is caused by this element in your system : c:\program files (x86)\checkpoint\zonealarm\vsmon.exe

Alongwith this one, Kaspersky itself is failing, too.

fffff880`0b095538 fffff880`03640000Unable to load image \SystemRoot\system32\DRIVERS\kltdi.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for kltdi.sys
*** ERROR: Module load completed but symbols could not be loaded for kltdi.sys
fffff880`0b095540 fffff880`0364c4e0 kltdi+0xc4e0
fffff880`0b095548 fffff880`03640000 kltdi
fffff880`0b095550 fffff880`0364c4b0 kltdi+0xc4b0
fffff880`0b095558 fffff880`03640000 kltdi
fffff880`0b095560 fffff880`0364c498 kltdi+0xc498
fffff880`0b095568 fffff880`03640000 kltdi
fffff880`0b095570 fffff880`0364c36c kltdi+0xc36c
fffff880`0b095578 fffff880`03640000 kltdi
fffff880`0b095580 fffff880`0364c24c kltdi+0xc24c
Description here: Driver Reference Table - kl... Read more

Read other 5 answers

I've tried to figure it out for ages and nothing works. It has happened so frequently that I've just sort of adapted to it interrupting me on a daily basis. Maybe you guys can chime in? I'm lost..

errors include: System Exception 0x0000003B, 0x00000000C0000005, 0xFFFFF800034C9044, 0xFFFFF88009136050, 0x000000000000000

and: STOP:0x000000BE / Win32k.sys etc.

Happens mostly while playing games, but also can occur during just regular browsing, etc.

A:BSOD While playing various games and just browsing, Errors: 0x0000003B

Still trying everything via. tips in this forum, nothing.

Read other 5 answers

Could really use some help in determining what's amiss. The crashes seem to randomly occur, at least nothing that I can pin point. I also tend to think this may be cause by both drivers and hardware as on at least two occasions the computer would not restart. When powered on, it failed post and went into a series of rapid beeps. I don't believe heat is an issue but it has taken awhile before I'm able to get it to reboot on those two occasions. I've read the posting rules and I believe all of the system info is listed on my profile and hopefully I've uploaded the dump file. but please let me know if I've missed something or there is additional information required.
Thanks in advance!

A:multiple random BSOD's ERRORs 0x0000001e and 0X0000003b

Hi darenot.

There is a high possibility that the BSODs are caused by NVIDIA nForce Serial ATA Controller. The storage controller element of nvidia chipset; specially RAID. c:\windows\system32\drivers\nvstor64.sys

fffff880`02f1ba40 fffff800`02ad15d1 CLASSPNP!TransferPktComplete+0x1ce
fffff880`02f1bac0 fffff880`0110d6c8 nt!IopfCompleteRequest+0x341
fffff880`02f1bbb0 fffff880`0110d443 storport!RaidUnitCompleteRequest+0x208
fffff880`02f1bc90 fffff800`02ad830c storport!RaidpAdapterDpcRoutine+0x53

fffff880`02f1b978 fffff880`0117500fUnable to load image \SystemRoot\system32\DRIVERS\nvstor64.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nvstor64.sys
*** ERROR: Module load completed but symbols could not be loaded for nvstor64.sys
Which is too old.

Image name: nvstor64.sys
Timestamp: Tue Jun 23 03:53:37 2009 (4A400469)
It is almost impossible to find updates to nvidia chipset nowadays; specially for such an old HP.

BiosVersion = 5.27
BiosReleaseDate = 06/10/2008
SystemManufacturer = Hewlett-Packard
SystemProductName = D5468AT-ABA ALONPAV
So I would suggest you to get rid of the nvidia elements and use windows system native elements.

Boot into the BIOS. Disable RAID. Then perform a Clean Reinstall - Factory OEM Windows 7

If you follow the guide step by step, it will lead to a perfect windows install which is driver complete itself. No need to install any drivers from nvidia o... Read more

Read other 1 answers

Hi Guys,

This is my first attempt at building my own computer so I am not a pro by any means. I've been having issues with blue screens ever since I put the thing together. All the parts are new out of the box. When I first put the machine together I did some troubleshooting on my own and with a NewEgg tech. The tech couldn't pin point the issue so he advised me to RMA the motherboard and RAM.

I got the replacement motherboard and RAM a few days ago but the issue persists. I am using BlueScreenView to look at my minidump files. BlueScreenView is listing all kinds of drivers and errors. Nothing really consistent. The time between crashes is also random. Sometimes it will crash when I login to windows and sometimes it will take a couple hours depending on what I am doing. I have noticed that I can crash it by opening a bunch of browser tabs and windows.

Here is a list of things I have tried:
1. RMA motherboard and ram
2. Downloaded latest drivers from gigabyte website and nvidia
3. Removed graphics card and used built in graphics (Have not tried with new RMA parts)
4. Updated motherboard BIOS from F3 to F6 version
5. Disabled built in graphics from BIOS menu
6. Tried 1 stick of ram at a time (Have not tried with new RMA parts)
7. MemTest 86 got Zero errors
8. Reinstalled OS (tired this with original parts and with new RMA parts)
9. Uninstalled anti virus
10. Updated fireware on ssd drive (c: drive)
I've don't troubleshooting with NewEgg techs and Gigabyte techs and... Read more

A:Constant BSOD on new custom build - Various Minidump Errors 0x0000003b

Please follow | Windows Genuine and Activation Issue Posting Instructions

Read other 9 answers

While the system is at idle or just light use I get the BSOD. It happens once a day and there seems to be no trigger. Core temps are at normal and run about 40 Celsius. I have tried updating most of my drivers through the device manager and will run a memtest soon. Any and all help is much appreciated, thank you!

Is Windows 7 . . .
- x64
- the original installed OS on the system? windows 7
- an OEM or full retail version? full retail

- What is the age of system (hardware)? 1.5 yrs
- What is the age of OS installation (have you re-installed the OS?) 1.5 yrs. have not reinstalled OS

System Specs
CPU: AMD Phenom(tm) II X4 920 Processor
Motherboard: ASUSTeK Computer INC. M4A785-M
BIOS: BIOS Date: 04/14/10 17"53:51 Ver: 09.06
Total Memory: 4.00 GB
Usable: 3.75 GB
HDD: (1) ST31000520AS ATA Device (2) Seagate Portable USB Device
Sound Card: (1) ATI High Definition Audio Device (2) High Definition Audio Device (3) C-Media PCI Audio Device
Graphics Card: ATI Radeon HD 4200
OS: Microsoft Windows 7 Home Premium 64-bit 7600 Multiprocessor Free

A:BSOD at random, errors 0x0000001e, 0x00000024, 0x0000003b, 0x00000050

Run a chkdsk on the system partition to check for bad sectors or system errors.
Disk Check

Read other 9 answers

for the last few weeks I have been receiving a whole bunch of BSOD errors. I have tried absolutely everything I possibly can to resolve this issue. I ran a memtest86 for 8-9 hours with 4 passes and no errors, I have completely removed my HDD's and replaced with a new SSD drive and I have also updated my BIOS but to no avail I seem to be still suffering from BSOD..

Any help would be massively appreciated.

PS: x0000000a and 0x0000010e BSOD were received after I had updated my BIOS.

here is my DM collected log with my DMP files:

A:Multiple BSOD errors 0x0000010e 0x00000001 0x0000000a 0x0000003b

This is either graphics driver issues or GPU failure.

I recommend ruling out the possibility of a failing graphics card first.
Run Furmark by following these instructions. (Run for around 30 minutes.)

Video Card - Stress Test with Furmark

fffff880`0837c738 fffff880`042fa22f : 00000000`0000010e 00000000`0000001f fffff8a0`0a4a7dd0 00000000`00000000 : nt!KeBugCheckEx
fffff880`0837c740 fffff880`04a211d0 : fffff8a0`0a4a7dd0 fffff8a0`0a4a7dd0 00000000`001f8ed3 00000000`00000000 : watchdog!WdLogEvent5+0x11b
fffff880`0837c790 fffff880`04a1e9d3 : 00000000`00000000 fffffa80`1508b050 00000000`00000c3a fffffa80`154350f8 : dxgmms1!VIDMM_GLOBAL::ReferenceAllocationForSubmission+0x148
fffff880`0837c7d0 fffff880`04a387d9 : 00000000`00000000 fffff8a0`090f6120 fffffa80`00000000 fffffa80`14fe7660 : dxgmms1!VIDMM_GLOBAL::PrepareDmaBuffer+0xe1b
fffff880`0837c9a0 fffff880`04a38514 : fffff800`00b96080 fffff880`04a37f00 fffffa80`00000000 fffffa80`00000000 : dxgmms1!VidSchiSubmitRenderCommand+0x241
fffff880`0837cb90 fffff880`04a38012 : 00000000`00000000 fffffa80`152161a0 00000000`00000080 fffffa80`132ec410 : dxgmms1!VidSchiSubmitQueueCommand+0x50
fffff880`0837cbc0 fffff800`033702ea : 00000000`01c9340d fffffa80`12e6ab50 fffffa80`0d318990 fffffa80`12e6ab50 : dxgmms1!VidSchiWorkerThread+0xd6
fffff880`0837cc00 fffff800`030c48e6 : fffff800`0324ee80 fffffa80`12e6ab50 fffff800`0325ccc0 fffff880`01b7038f : nt!PspSystemThreadStartup+0x5a
fffff880`0837cc40 00000000`00000000 : 00000000`00000000 00... Read more

Read other 9 answers

Had a BSOD on Sunday. Took the sides off the computer to find the heatsink caked in dust. Cleared that out with some compressed air and seemed to do the trick just fine. Computer fan running much quieter too then.

All fine on Monday and then cranked the PC up this evening and BSOD again. Couldn't get Windows to start, so tried removing RAM and then removing all hard drives except my boot drive containing Windows. Set up is SSD with Windows on, second SSD with programs on, HDD for files and data and second HDD for backup; that set up has been running fine for some time.

Have managed to get Windows to load and no BSOD currently, with three drives plugged in and the main HDD for data NOT plugged in. Not sure if that drive is the common problem.

Some BSOD messages I have seen, before it vanishes, include PAGE_FAULT_IN_NONPAGED_AREA and REGISTRY_ERROR and SYSTEM_SERVICE_EXCEPTION

Any help and advice much appreciated. The diagnostic data was run without said HDD plugged in.

Brief update.....
PC still running but trying to shut down, I get a Windows Explorer has stopped working error, as below. Could this be linked to the other drive not being plugged in? The unplugged drive contains my 'Desktop' so I wonder if this is confusing Windows somehow. Only way to shut down seems to be to just power off.

Problem signature:
Problem Event Name: APPCRASH
Application Name: Explorer.EXE
Application Version: 6.1.7601.17567
Application Timestamp: 4d672ee4
Fault Module Na... Read more

A:BSOD multiple errors, error 0x00000050 and error 0x0000003B

Hiya and welcome to SevenForums!

BugCheck A, {fffff900008d1ee9, 0, 0, fffff80002ad41dc}

Probably caused by : win32k.sys ( win32k!AllocThreadBufferWithTag+24 )

Followup: MachineOwner
Hmm, re-install Windows as your getting 0x51 errors because 0x51 errors are registry related errors.

Read other 9 answers

I am randomly getting a BSOD. I have found no pattern to when I get it. (Gotten it gaming, browsing internet, and so on.) Browsed internet and the forums here and have not found anything useful looking. Attached is the .zip from the SF diagnostic tool.

Thanks in advanced for helping.

A:BSOD Random 0x000000BE nvlddmkm.sys


Microsoft (R) Windows Debugger Version 6.12.0002.633 X86
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\Users\Yusra\Downloads\StarrBurst\090712-29312-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: SRV*C:\SymCache*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 7 Kernel Version 7601 (Service Pack 1) MP (6 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS Personal
Built by: 7601.17835.amd64fre.win7sp1_gdr.120503-2030
Machine Name:
Kernel base = 0xfffff800`03200000 PsLoadedModuleList = 0xfffff800`03444670
Debug session time: Sat Sep 8 07:23:15.837 2012 (UTC + 6:00)
System Uptime: 1 days 12:30:52.992
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
* *
* Bugcheck Analysis *
* *

Use !analyze -v to get detailed debugging information.

BugCheck BE, {fffff8801361d6... Read more

Read other 9 answers

I've been having more and more frequent bluescreening lately, it's happening a lot when I play games (e.g. Hearthstone and ARMA 3) but seems to be fine when watching videos and doing other things. There are also instances that my computer simply freezes without a bluescreen, resulting in me having to press the reset button in order to reboot.

I googled around and downloaded a program BlueScreenView which has shown me the dump files, a lot of it makes no sense to me because I've never looked into this kind of thing before. It's telling me that it's casued by three things;
ntoskrnl.exe+72a40 and,

The "Bug Check Codes" are in the title of the post, with the strings; ATTEMPTED_WRITE_TO_READONLY_MEMORY,

I can see it is a Driver issue, or at least some of it but I don't know how to identify what driver to reinstall it... These are going back as far as the 20th of March and has happened 6 other times since then, which I don't feel is normal. I have uploaded a .zip that was created from a program this site had me download.

I appreciate any and all help on this matter. If you need any more information that I haven't provided, please ask and I will reply as quickly as possible to get this sorted.

A:BSOD Randomly, mostly during gaming 0x000000be / a / c5

Bumping this thread, still haven't fixed the issue yet.

Read other 4 answers

Hi all,
Yesterday (27 July) I experienced my first ever Windows 8 BSOD. What happened was that I had found myself on a website I didn't quite trust, and I closed it, then ran Malwarebytes out of precaution because I am a paranoid laptop user ^^; As soon as Malwarebytes had updated its database and was about to scan, I received a BSOD with the code "Attempt to write to read only memory" I panicked and started checking up on everything after the reboot and noticed that every site that usually remembered my login had logged me out, which made me worry about a possible virus intrusion since something (I assume) was trying to write to the Windows portion of my disk? Maybe it was trying to get my passwords too, I don't know.
I shut down the laptop and went to work, and didn't touch it until this morning. Event viewer didn't really help that much except for identifying a problem with my wireless connection dropping, which I will attempt to fix soon . I then looked at the Minidump with WinDbg which pointed at ntkrnlmp.exe - after lots of Googling I found that apparently that isn't the cause at all, it's just that ntkrnlmp was handling the bad data at the time. It also said the process was mbam.exe, which I found is Malwarebytes.
That's about as far as I can understand computer language, so here I am, bugging everyone here. This has only happened once on this machine that I am aware of, and doesn't seem to be showing signs of wanting to BSOD again. It's more a paranoia th... Read more

A:First ever Win8 BSOD 0x000000BE probably by ntkrnlmp.exe ?

And apparently the SF Diagnostic tool hadn't finished running when I uploaded the compressed file of it.
Here is the complete one!

Read other 8 answers

Mate's PC, using an old Asus Striker Extreme with 7 Pro 64bit on it, randomly bluescreening. Hiren's memchecks found no issue, but removed a couple of sticks leaving 4Gb down from the original 6Gb. Seems more stable now but not perfect. Oddly the memchecks. For instance, had Comodo installed on it, worked ok, updated, ran fine, post a reboot randomly will stop working, can't repair itself, stripping it out and re-installing, nada. This machine may stay up for days, may just randomly bluescreen, sometimes x000000BE, once I noticed 1E. Bios beeps not helpful. link now removed as zip attached below Hoping that you can spot something from the logs. Thank you for your time

A:Random BSOD, 0x000000BE, removed Ram but still issues

Post it following the Blue Screen of Death (BSOD) Posting Instructions.

Read other 4 answers

Hey everyone,

It's been some time since I posted. Since my last post here I found that the line of motherboards I was using were faulty in their design. Since then I switched brands completely and I had been BSOD free for over a year. Then on Thursday I got a BSOD, followed by two more yesterday. The errors were always "Attempted_to_write_to_readonly_memory."

Since then I checked for spyware and it came back clean. I tested both hard drives with the "chkdsk" tool and they came back error free. I also ran driver verifier but my system crashed before windows could fully boot, so I had to turn it off in Safe Mode. I ran Memtest86+ and after three passes my system came back with an error. I pulled one 2GB stick of RAM, and after 7 passes the no errors showed up. I swapped out the RAM and tried the other stick. 11 Passes later I had 25 errors. So I switched the sticks again and tried driver verifier once more with the RAM that didn't give me any problems. I couldn't get windows to load yet again. So it seems my problem goes deeper than one stick of bad RAM.

I'm not sure what to do now but I'm hoping someone can help me pinpoint the problem. My files from the SF tool are attached. Any help would be very much appreciated!

A:BSOD, RAM and Driver Problems of the 0x000000be Variety

Well like you said, bad RAM. there was a NTFS file system error.

Try running:

SFC /SCANNOW Command - System File Checker

Disk Check

Then post back results.


Read other 5 answers

Recently I have been getting BSOD errors. These errors have been occurring randomly and are when I am watching youtube videos and other times such as when I have restarted my computer. The stop codes I have been getting on my BSOD screen have been changing at first it was 0x0000001A but it has recently changed to BE. I'm not a computer wiz so I am not up to grasp with computer lingo so you might have to dumb stuff down for me.

A:BSOD Watching youtube video, error 0x000000BE

Hello Calum and welcome to Sevenforums.

Don't worry, we're all fully respectful and understands that some people may not have the proper skills at computers in order to fix such issues. I'll take care.

First off, thank you for providing the crash dump files, though we need a little more than that. If you haven't already, you can install our utility that'll gather all the thing you'd need to provide, in order for us to analyse your BSOD.
The additional files includes, nfo, systeminfo etc. To get these files, use our thread below.


Best Regards,

Read other 1 answers

I can't load Windows XP in normal or safe mode ... I keep getting the following BSOD / GSOD (green) error: "An attempt was made to write to read-only memory" with Stop error 0x000000BE (0x806FE800, 0x006FE121, 0xF78AE784, 0x0000000B) at the Windows XP start-up screen.

Over the last few days I cleaned a few viruses (maybe 1 or 2 rootkits) off my computer using Spybot S&D, Super AntiSpyware, MalwareBytes, AntiVir, CWShredder, HiJackThis, several other online anti-virus/malware scanning engines and then cleaned the leftover temp files and registry keys using CCleaner and RegistryBooster. Throughout the process, I made several registry backups using ERUNT. Windows XP did not have any noticeable problems loading throughout all this.

Last night, I installed DataPilot software by Susteen (used to backup data from cell phones). This software installs over 300 registry entries along with numerous [unsigned] cell phone drivers. The installation seemed to go well and Windows XP loaded up fine 2-3 times after the initial install.

When I booted up the computer this morning, I received the BSOD error. The BSOD screen was actually greenish colored (GSOD) instead of the normal blue color. I have tried all of the following but still receive the BSOD error: I disconnected all USB devices and rebooted; I used some compressed air to clean out the case; I reseated the RAM; I de-/re-attached the hard drives; I tried ?last known good configuration?. When I... Read more

A:BSOD stop error 0x000000BE on loading Windows XP

I would suggest you to rather focus on Daemon Tools left over files i.e. SPTD.sys etc. and remove these. You can use the bootable cd available to you, and try finding sptd.sys on your hard driver and manually erase it.

For any help with regard to erasing unwanted entries from your OS's registry, please have a look at this article.

Also, as you are unable to find any minidumps, probability is they are not being recorded or configured to record.

If the above suggestion doesn't help, you are better off trying to do a repair install.

Read other 1 answers

I switched on my PC today and halfway through the boot screen it goes into BSOD.
The error code goes something like

STOP 0X000000BE (0x**, 0x**,0x**,0x** I don't know whether this bracket part matters)

with the message: attempted to write to readonly memory

The bluescreen immediately turns green with remnants of the loading bar stuck on the screen.

Attempting to go into safe mode results in the same message except it only flashes for a split second (and stays blue) before it auto-restarts.
My PC is a windows XP. I do not have a windows XP CD so I can't boot with that. The only way I can boot right now is to use another hard drive containing XP also using a SATA cable, in case I need to modify files on the "problematic" hard drive. This means that I do not run the problem'ed OS at all when I alternate boot, unless I could find a way to do it.

I do not think it is the haxdoor virus since I couldn't find the driver in problemdrive:/windows/system32/drivers.
Also, I did not install any new drivers or hardware. The newest hardware I've used so far is a new USB external 2.5 hard drive which seems to work fine for the past week I've been using.

The last time I shutdown, during the shutdown message, I plugged out the USB external hard drive before it is completely off, which I do not know whether it is the cause.

I heard that loading the hive in regedit of "system" from the problemdrive:/windows/system32/config and deleting t... Read more

A:XP BSOD on bootscreen (STOP 0x000000BE, attempted write readonly memory)

Read other 7 answers

My computer has recently started having this random BSOD, after working normally for the last few years. The first BSOD had happened on 9/12/15 while playing the game Subnautica; after this blue screen, the computer rebooted only to get the same BSOD again. I then did a system restore to a previous point and the blue screens stopped, though they returned today (9/19/15) again. This time the BSOD happened randomly as soon as windows was started and loaded up the desktop.
What I have noticed is that prior to these BSOD, there has been a quite high usage of RAM (and wuauserv was also using lots of computer resources), even when here were no programs or games running. I'm not sure what caused these blue screens since there were no dmp files made during the previous BSOD, only on the most recent one.
I also noticed that in the BSOD, it said something like "Attempted to write in read only memory"
Today after the computer rebooted from the BSOD, I got this displayed:
"Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7601.
Locale ID: 1033

Additional information about the problem:
BCCode: be
BCP1: FFFFF900C2B82000
BCP2: 55900000BD583021
BCP4: 000000000000000B
OS Version: 6_1_7601
Service Pack: 1_0
Product: 768_1"
and this in the event viewer:
"Log Name: System
Source: Microsoft-Windows-WER-SystemErrorReporting
Date: 9/19/2015 1:11:31 PM
Event ID: 1001
Task Cate... Read more

A:Random BSOD that occur 0x000000be/attempt to write on read only memory

Also after the BSOD that happened today, the computer wouldn't start up; It was just beeping continuously. I had to unplug it from the wall and replug it back for it to restart. Once again I did a system restore. Help would be appreciated for this BSOD.

Read other 1 answers



A:(0x0000003b) and other errors

With this information we can help
Blue Screen of Death (BSOD) Posting Instructions
Without this information any other suggestions would just be guesses.

Read other 37 answers

Hey, so I was playing SWTOR and I got the BSOD. It has occurred several times in the past day. Here is the information.

I have run memtest already and have had 0 errors. I have all my drive up to date. I also reformatted my computer-NOT REPAIR, but FULL WIPE.

I have attached information via the instructions in thread.

Thank you for your time.


The crash dump blames hardware.

Re run these tests again

RAM - Test with Memtest86+

errors might be detected after 7 passes

Do this overnight


Hardware - Stress Test With Prime95

Read other 9 answers

My computer has been doing this a lot recently and its started doing it more often, usually the 0x0000003b code pops up when either windows media player is on or when it is stood idle for a while. Using NirSoft's bluescreen viewer it stating that the ntoskrnl.exe is the problem in all minidumps, it also sometimes states nvator64.sys is the other file that causes the bluescreen. i have attached the minidumps to this and hopefully someone will tell me how to fix it, i have checked online and gathered it down to these 3 options... either my PSU is not powerful enough to support the payload, my HDD is corrupt or the RAM is stating to fail. Thank you for the people who can help! as a side note, i have tried formatting and reinstalling my windows 7 64bit ultimate, but the BSOD can appear on setup and did at one point so i had to renew the whole setup, recently it has started doing it a lot more. one happened not too long ago and also had the CDD.dll file as an error. Also before anyone says it, YES MY DRIVERS ARE ALL UP TO DATE! there are literally no updates available for my hardware which is why i think its either my HDD or RAM.

My Specs:
AMD Athlon II X2 245 2.91 Dualcore
Gigabyte M52LT-D3
4GB (2x2GB) DDR3 RAM (not sure on the manufacturer)
NVIDIA Geforce GT 440
500GB Partitioned Western Digital Sata II HDD

A:BSOD - getting BSOD error 0x0000003b a lot while idle or playing music

UPDATE: this just happened to me aswell... states the NTFS.sys is now the error (Error code 0x00000024) was literally only thumbing through facebook nothing else.

Read other 9 answers

Hi, in the middle of any kind of game i'm playing, my computer will go black and say "monitor going to sleep" as if i pressed the button to turn off the monitor but the difference is the only way i can revive it is to restart it. This kinda gets really annoying so i'd appreciate any suggestions.

A:General Gaming errors

Open the monitors settings menu and disable any powersaving options.
There should be three buttons on the front of the monitor-the middle one should open
the monitors menu.

Read other 5 answers

Logfile of Trend Micro HijackThis v2.0.2
Scan saved at 9:56:38 PM, on 5/6/2008
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v7.00 (7.00.6000.16640)
Boot mode: Normal

Running processes:
C:\Program Files\Viewpoint\Common\ViewpointService.exe
C:\Program Files\Common Files\PCSuite\DataLayer\DataLayer.exe
C:\Program Files\iPod\bin\iPodService.exe
C:\Program Files\Viewpoint\Viewpoint Manager\ViewMgr.exe
C:\Program Files\Mozilla Firefox\firefox.exe

R0 - HKCU\Software\Microsoft\Internet Explorer\Main,Local Page =
R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Start Page_bak = http://www.hotmail.com/
R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Local Page =
O2 - BHO: e404 helper - {03B902B1-9B25-4173-9468-56775C85A8D4} - C:\Program Files\Helper\1204161382.dll
O2 - BHO: (no name) - {089FD14D-132B-48FC-8861-0048AE113215} - (no file)... Read more

Read other answers

First of all I'd like to wish you all a merry Christmas and thank you in advance for any support you guys can offer.
I have win 10 installed and first noticed problems whilst playing a game on steam which suggested a problem with my disk, all disk scans found no errors though. I did a fresh install of windows 10 Education 64-bit but experienced problems updating getting the error 8073712 (I think). I've downloaded and run win 10 update assistant but that failed to solve the problem. I stopped using an AV instead trusting windows defender and no problems were found, I even downloaded the windows security troubleshooter with up-to-date virus, malware and pup definitions (which is only valid for 10 days) and no problems were found.
I've downloaded whocrashed and this is the report:
Computer name: (I've hidden this)
Windows version: Windows 10 , 10.0, build: 15063
Windows dir: C:\Windows
Hardware: Gigabyte Technology Co., Ltd., 970A-DS3P
CPU: AuthenticAMD AMD FX™-6300 Six-Core Processor AMD586, level: 21
6 logical processors, active mask: 63
RAM: 8552898560 bytes total
Crash dump directory: C:\Windows\Minidump
Crash dumps are enabled on your computer.On Mon 25/12/2017 10:38:36 your computer crashed
crash dump file: C:\Windows\Minidump\122517-24343-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x16BFD0)
Bugcheck code: 0x50 (0xFFFF8B86688B94F0, 0x0, 0xFFFFF8029C271DFC, 0x2)
file path: C:... Read more

A:Update errors, BSD and general pc problems

This topic should be moved to the Windows Crashes, BSOD, and Hangs Help and Support.

Read other 17 answers


I have a general question about some faulting modules being logged in the Windows Event Viewer.

An error leading to crashes of certain applications I have seen multiple times now when supporting computer problems is something like this:
(Windows Error Reporting) Fault bucket, Type 0, Event name: PCA2, (...) P1: application.exe, (...)

I'm wondering what this 'PCA2' is. Is that some kind of Windows module handling certain tasks like memory allocation or sth. like that? What could be the cause of such errors (physical memory problems / corrupted swap file / insufficient rights ?)

Same Question for application crashes due to 'kernelbase.dll' as in:
(Application Error) Faulting application: application.exe, Version:, (...) Faulting module: KERNELBASE.dll, Version: 6.1.7601.18015, (...) Path of faulting module: C:\Windows\syswow64\KERNELBASE.dll (...)

What's this .dll file for and what could possibly cause kernelbase.dll to fault?

The application may be somewhat bugged, but I'm wondering what could possibly cause those crashes and if there's a way to correct these issues - or what the dev's doing wrong.

Both errors occur mainly on x64 systems - mostly Windows 7/vista

Kind regards

A:General questions on errors in eventvwr

Those problems could be due to software conflicts, corrupted system files, corrupted software installations, registry damage due to using registry cleaning programs, or even hardware failure with RAM and the hard disk being prime suspects. Viruses can also lead to event viewer errors similar to or the same as what you describe.

How to perform a clean boot to troubleshoot a problem in Windows 8, Windows 7, or Windows Vista
If you are overclocking any hardware, please stop.

Run Disk Check with both boxes checked for all HDDs and with Automatically fix file system errors checked for all SSDs. Post back your logs for the checks after finding them using Event Viewer. In Event Viewer, expand Windows Logs, click Application to let it load, right click Application and click Find.... Search for chkdsk or wininit to find the logs.
For any drives that do not give the message that no problems were found, run the disk check again. You do not want the message shown in red below. You do want the message shown in blue below.
Windows has checked the file system and found no problems Windows has made corrections to the file systemSome helpful links:
Check a drive for errors

Open Event Viewer
Run all Basic tests with SeaTools: S.M.A.R.T. Check, Short Drive Self Test, Drive Information, Short Generic, and Long Generic. Run the tests for all HDDs.SeaTools for Windows

SeaTools for DOS

Bootable Hard Drive Diagnostics
Check your drive Health and run an Error Scan with HD... Read more

Read other 1 answers

Got a new 1.8 ghz celeron, 128mb ddr ram, 40 gb HD, running xp home and working, updated antivirus software. Had it for 2 weeks, now getting errors about not enough memory, and intermittant crashes. It has to be unplugged to get it going again,will not work by shutting it down thru windows. It is used to create word documents and light internet use. what is up>

A:errors,restarts,general disruption

Read other 6 answers

Alright. Could anyone perhaps help me with this?

I've got a computer of around 2-3 years old.. (not a hardware issue, so not listing details) and now it's starting to be annoying. You see, whenever I get the general "Program caused errors, writing log" or something (I belive you know what I'm talking of, the general most common application error) the computer crashes in middle of logging about the errors. No bluescreen, no sudden crash. Just stops responding.

I first thought it was a registery flaw, but I've tried several programs and none of them found anything to fix it. Perhaps it's a missing program that writes the log file? Which program does it? Maybe I lost the program somehow?

Is there a way of reinstalling microsoft default programs and/or registry? It's getting rather annoying to have a computer crash every hour due to certain programs crashing (normally they don't crash the computer along with it, but since I'm probably missing the windos files that a) closes application or b) writes a log of it, OR registery links to it.. but as I said previously, as I found nothing, I don't think it's a registry issue.

Hmmh. Did I tell you that if I press "cancel" during the error (few seconds before it starts dealing with logging the error, at the time of closing program) I can actually prevent the system crash? But usually this is not enough, since it's only few seconds.

Ack. Has anyone even had sim... Read more

A:Problem with w2kpro general program errors

Read other 6 answers


The problem I have at the moment is very similar to this thread on the forums.

To the best of my knowledge the computer in question just simply suddenly stopped working as it should. I am unable to get the 'default' welcome screen upon start up and am getting the logon box where you type in a username and passworld. I know how to get rid of this, user accounts>enable welcome screen - but it will not solve the problem.

This is just the start of the problems. I get a whole host of errors which popup one after another. This is a summary of the errors which popup:
userinit.exe bad image
hpztsb05.exe bad image
psdiagnostic.exe bad image
vscplay.exe bad image
ituneshelper.exe bad image
zlclient.exe bad image
wcescomm.exe bad image

Once these errors pop up the desktop picture appears, but no icons/start menu are available. I have to ctrl/alt/delete then run a command (such as control or winword) then I get the icons and the start menu. However most programs cannot run at all, for example I cannot run Spybot, I get the error: 'SpybotSD.exe - bad image' 'The Application of DLL C:\WINDOWS\system32\winspool.drv is not a valid windows image. Please check this against your installation diskette'.

Basically I cannot tell if this is a spyware/adware/virus/HDD failure problem. I can however run AVG antivirus, and it finds no problems.

I've tried runnin HijackThis but again the program will not run. It shows the same error as when I try to run Spybot.

Does ... Read more

A:Bad Image Errors/General Booting Problems


Read other 1 answers

Hello. This is my first time posting on here and i'm hoping that maybe I could resolve my problems here. I have had this BSOD problem for about 6 months (January-now). I'd also like to mention that i'm not exactly a very proficient person when it comes to computers so i'm sorry if I don't understand some things.

So I have had this BSOD problem since late January. Since January, I have recieved 5 BSOD's that were all BCCode 0x3b (System_Service_Exception). I have tried a couple of things in attempt to fix my problem, but I don't think they worked. I tried:

1. Updating my video card drivers.
2. Updating Windows (since it was nearly a year outdated)
3. Scanned my PC with Malwarebytes.

I know there are several other fixes I could of tried such as driver verifier and testing RAM, however I wanted to consult this forum before I attempted to do those things as I worry I might screw something up.

There are a few things i'd like to mention.

Firstly, my first 0x3b BSOD occured 2 days after I got my new mouse (Logitech g500) and has since been happening. I have never tried uninstalling the drivers or using a different mouse but I might try that if it turn out to be a possibility.

Secondly, these BSOD's are very intermittent. My most recent BSOD was on June 8. Prior to that, the last BSOD I got was in February so it will be difficult to test to see whether any suggestions actually worked.

Thirdly, in October of 2013, I got a BSOD 0x0a upon attempting to wake my ... Read more

A:BSOD 0x0000003b

Hello PureLemon,

Unfortunately the .zip folder you have uploaded is incomplete. We need more information to analyze your logs. Follow Blue Screen of Death (BSOD) Posting Instructions, let the tool run until it has completely finished and then upload the new logs.

Read other 3 answers

This is the first blue screen i have gotten in a month. If someone could help me with it it would be appreciated.

For some reason when i go to check it it says the symbols im using is incorrect.
I downloaded the supposed "hotfix" for this error from microsoft but obviously its not working.
ALL my drivers are up to date. Nvidia v260.99. Latest realtek LAN drivers. Latest ACHPI cooling drivers. Latest Via HD sound drivers. I will not upgrade my bios from the 2002 to 2012 because it causes errors in the bios.

It would be great if someone could help me so i can fix this problem. I uploaded the minidump file as well. Thanks again.

A:Help BSOD 0x0000003B

Please do the following:

BSOD Posting Instructions



Does this happen only when you playing Black Ops, or other Internet activity?

Read other 6 answers

HI I just built my computer a few months ago and just recently i started getting BSOD every few days or so and i dont know what is causing it or how to fix the problem so... that is why i cam here
the only old parts i took from my old computer are the cd drive and a usb2.0/card reader thing
Can someone please tell me how to fix this problem?

A:BSOD 0x0000003B Please Help

Quote: Originally Posted by natedogg409

HI I just built my computer a few months ago and just recently i started getting BSOD every few days or so and i dont know what is causing it or how to fix the problem so... that is why i cam here
the only old parts i took from my old computer are the cd drive and a usb2.0/card reader thing
Can someone please tell me how to fix this problem?

This was Related to D-Link_Range_Booster device. Note: Located in \%Program Files%\D-Link\D-Link DWA-552 Xtreme N Desktop Adapter\. I would remove it or if necessary update it to newest version.

Read other 1 answers

Constant BSOD for a few days now (happen randomly w/o any notification). Tried from changing antivirus (Avast->Avira), cleaning graphic drivers, sfc scans and repairs, partition defragmentation,...

I attached latest dump file.

Thank you for your time and help!

A:BSOD 0x0000003b

Hi Marjomire123.

You have Entrust Entelligence Security Provider which is causing the BSOD. It looks like an old version (4 years old, I am not very aware of their update policy).

Try to get an update to the latest. If no update is possible, I will suggest you to uninstall it.

Let us know the results.

* *
* Bugcheck Analysis *
* *

Use !analyze -v to get detailed debugging information.

BugCheck 3B, {c0000005, fffff80003f638f5, fffff8800ae32a70, 0}

*** WARNING: Unable to verify timestamp for eetd64.sys
*** ERROR: Module load completed but symbols could not be loaded for eetd64.sys
Probably caused by : eetd64.sys ( eetd64+16ac )

Followup: MachineOwner

0: kd> !analyze -v
* *
* Bugcheck Analysis *
* *
******************************************************... Read more

Read other 2 answers


I brought a brand new Toshiba A660 laptop from a retail store a couple months ago.

While using the latest IMVU (v450.0), my machine randomly blue screens once or twice during the session.

Others on IMVU forums who are having the same problem as me are also using Windows 7. Once they downgrade to Win XP, the BSoD stops.

I have contacted Toshiba who blame IMVU for software incompatibility. Toshiba say the laptop is not covered under warranty as they claim the fault is with IMVU. Toshiba stated that replacing the current graphics card is not the solution as there is nothing wrong with the current card. Seems to me that they do not want to take the blame and I feel helpless, ripped-off and stuck this with high-end laptop that isn't doing what its designed for.

I do not want to run recovery disk (as Toshiba suggested) as few others on IMVU forums have stated that that does not work.
I do not want to use an older version of IMVU as the latest version is needed to perform tasks that the later versions lack.

Please guide me through the procedures needed to stop the blue screens while using IMVU.

Thanks in advance.

A:BSoD 0x0000003b

Quote: Originally Posted by readayan


I brought a brand new Toshiba A660 laptop from a retail store a couple months ago.

While using the latest IMVU (v450.0), my machine randomly blue screens once or twice during the session.

Others on IMVU forums who are having the same problem as me are also using Windows 7. Once they downgrade to Win XP, the BSoD stops.

I have contacted Toshiba who blame IMVU for software incompatibility. Toshiba say the laptop is not covered under warranty as they claim the fault is with IMVU. Toshiba stated that replacing the current graphics card is not the solution as there is nothing wrong with the current card. Seems to me that they do not want to take the blame and I feel helpless, ripped-off and stuck this with high-end laptop that isn't doing what its designed for.

I do not want to run recovery disk (as Toshiba suggested) as few others on IMVU forums have stated that that does not work.
I do not want to use an older version of IMVU as the latest version is needed to perform tasks that the later versions lack.

Please guide me through the procedures needed to stop the blue screens while using IMVU.

Thanks in advance.

Hate to say it but your IMVUClient.exe is causing all of these. It is causing a memory exception. Just in case run memtest to check yours.

I would remove it
Download a copy of Memtest86 and burn the ISO to a CD using Iso Recorder or another ISO burning program. Boot from... Read more

Read other 2 answers

Hello, i built a new computer, and I've been getting Blue Screens. The first time I installed windows 7 (x64) and the blue screens were very frequent and random error codes. I uninstalled and reinstalled windows 7 (x64), and the Blue screens only happen when I turn on my computer once or twice, and its 0x0000003B. I had my RAM tested at a computer store, and they said it was fine, but im not sure if they were right. I have 2 x 2 sticks of RAM. Please help.

Edit: My hard drive is partitioned, not sure if its worth mentioning.

Edit: Fixed the attached files, thanks

A:BSOD 0x0000003B

Hi redgamma,

Unfortuneately you didn't pack the files produced by Windows_NT6_BSOD_v3.03_jcgriff2_.exe in your attachment.

You packed the actual Windows_NT6_BSOD_v3.03_jcgriff2_.exe!!

Read other 4 answers

Ever since installing my Phenom II x4 840 into my Gigabyte MA770-ud3 I've been getting loads of BSoDs. If I revert back to my old Athlon x64 everything appears to work. This is the second CPU I have tried as I thought the first one was faulty but this one is doing the exact same as well.

I have updated my motherboards firmware to ensure it supports Phenom IIs (FKb).

I've attached the zipped file which contains both the Perfmon and windows_NT6BSOD_jcgriff2 files.

Running Windows 7 x64 OEM
OS age around about a year and hardware is mixed as self build. Mostly about a year as well apart from the CPU.

Any help would be very much appreciated thanks.

A:0x0000003b BSoD

I should also have added that one of the BSoDs mentioned dxgkrnl.sys however dxdiag seems to find no problems. I've also attached this file in case it helps.

Read other 4 answers

Built my new computer and started getting this error, i don't know from what.

http://puu.sh/PwSQ - Windows Blue Screen Viewer

A:BSOD 0x0000003b

Hi xemath and welcome to W7 Forums

Are you using the latest graphics driver for your card, or the one that came with it?

Read other 2 answers

First time posting here. I've been getting this error once in a while, I've run memtest and updated my gpu driver and still gives me BSOD every now and then. help please. thanks!

A:BSOD 0x0000003b

No Service Pack 1, only 1 Windows Update. Please do the following:
SP1 isn't installed, please do the following:

Installing Windows 7 Service Pack 1
1. Visit the PC manufacturer's website and update ALL drivers. DO NOT use Windows Update or the "Update drivers" function of Device Manager.
2. Check Device Manager for any unknown/disabled devices - if there are unknown/disabled devices, fix them with the latest drivers from the device manufacturer's website (not the PC Manufacturer)
3. Visit Windows Update and get all updates (may take repeated visits)
4. Visit Windows Update and get Service Pack 1 (usually under Important Updates). Read these notes for installing SP1: Steps to follow before you install Windows 7 SP1 and Windows Server 2008 R2 SP1 from the Microsoft Download Center
5. Visit Windows Update and get any other available updates. May take repeated visits, but keep it up until you get several "Windows is updated" results.
If you're having difficulties with installing a Service Pack, please use the SURTool from this link: What is the System Update Readiness Tool?

We've seen a number of BSOD issues with SSD's recently. Here's the information that I've compiled:

There's not a whole bunch available to test SSD's. The "easiest" test is to remove the SSD, install a platter-based hard drive, install Windows and test for stability that way.

Here's some suggesti... Read more

Read other 3 answers

Hi. Firstly I want to say my computer knowledge isn't great, so sorry in advance if I do anything wrong or seem a bit slow at times - I'm doing my best.

I bought a Chillblast Sidewinder about 15 months ago, and it's been working almost flawlessly since then until the last couple of days. It will start up fine but after a period of time (ranging from 5 minutes to hours) it will crash out to the BSoD with a memory dump. I haven't been able to deliberately cause this to happen, it seems to do it randomly. The error message is (sorry, I don't know which bits are relevant):



then (I think in brackets) there are several addresses:

win32k.sys - Address FFFFF960000E5429 base at FFFFF96000010000
DateStamp 4a857827

(searching through past posts, this might be something to do with the RAM?)

On one occasion, while booting, some message came up about trouble with overclocking, but I can't remember what it said and it hasn't happened again.

I bought the system direct from Chillblast and haven't (nor would I know how to) change anything about it. The specs are:

Intel Core 2 Quad Core Q6600 overclocked up to 3.2GHz
Asus P5Q P45 Motherboard
4GB PC2-6400 Memory
Chillblast Radeon HD 4870 512MB
1000GB 7200RPM Hard Disk
Standard 20x DL DVD?RW SATA Optical Drive
Thermaltake High Performance 500W PSU
Microsoft Windows Vista Home Premium 64-Bit OEM... Read more

A:BSoD 0x0000003B

I'm not the best with debugging BSOD's, but I can tell you one simple step to take in trying to resolve the issue.

A common cause of BSOD's is out-dated drivers.

Try updating your drivers through the Device Manager.

Read other 3 answers

here is the information asked for. Please help. Thank You.

A:BSOD 0x0000003B

Update drivers. Red, bold fonts mean they definitely need update.

pcouffin.sys Wed Dec 06 03:39:30 2006
Recommend to uninstall the program.

ASACPI.sys Thu May 14 13:25:17 2009

Product - Motherboard
Series - SocketAM2/AM2+/AM3
Model - M3A76 -CM

Click on utilites and click on the first one (ATK0110 driver for WindowsXP/Vista/Win7 32 & 64-bit)

Read other 9 answers

Ok, so I just built my computer about 3 days ago. These are all my components:


Windows 7 - 64bit


RAM (16GB):

G.SKILL Ripjaws Series 8GB (4 x 4GB)



AMD Phenom II X6 1100T1






Cooler Master 1200W Silent Pro Gold


Graphics Card:

SAPPHIRE 100312SR Radeon HD 6950 2GB 256-bit**



I keep getting BSOD (Blue Screen of Death) Errors on my computer RANDOMLY! I don't understand why it is doing this! I really want a solution. I need to actually be able to use my computer with all these expensive hardware without it crashing!



2shared - download My BSOD Error.zip

I have included a WinRAR File with the MiniDump (DMP) Files and I've even included the actual image of the BSOD taken from my iPhone.

I updated all my drivers, including the Graphics Card (from the Stock Website and CD), and it is still giving me issues.


If you guys need any more information please let me know!

All help is greatly appreciated. Thanks!



A:BSOD Help!! (0x0000003b)

As priority, test your RAM with memtest86 for at least 7 passes.
RAM - Test with Memtest86+

If the memtest did not show any error, then I suggest you to enable Driver Verifier.
Wait until next crash then upload the new files here.
Blue Screen of Death (BSOD) Posting Instructions


Windows 7 Kernel Version 7600 MP (6 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16695.amd64fre.win7_gdr.101026-1503
Machine Name:
Kernel base = 0xfffff800`02a4f000 PsLoadedModuleList = 0xfffff800`02c8ce50
Debug session time: Tue Apr 5 23:02:55.362 2011 (GMT-8)
System Uptime: 0 days 1:50:47.642
Loading Kernel Symbols
Loading User Symbols
Loading unloaded module list
* *
* Bugcheck Analysis *
* *

Use !analyze -v to get detailed debugging information.

BugCheck 3B, {c0000005, fffff80002a9bf87, fffff88008e99f00, 0}

Probably caused by : ntkrnlmp.exe ( nt!KiDeliverApc+a7 )

Followup: MachineOwner

2: kd> !analyz... Read more

Read other 1 answers

My computer has been generally slow for a while, but suddenly one day it was having a lot of issues. 3 blue screens over the course of two hours despite only using chrome type issues.

I set it up to check the C-drive, restarted to initiate that and went to bed.

The next day it seemed to be fine. The day after that I shut down and when I came back I noticed it was on the log-in screen as if it had restarted instead of shut down. So I logged in and shut it down again.

When I came back the next morning it was very slow to start-up, staying on the initializing screen after log in for 5-10 minutes. When it finally loaded all transparency was gone and it was extremely slow in general. When I tried to check the event viewer I got a "the snap-in is not responding" error and it wouldn't work. I checked for updates and saw there was one for my graphics card so maybe it was a graphics card issue, but the update errors. I tried checking the properties of my C-drive again but every time I right click it windows explorer errors and restarts.

I'm restarting again to see if that helps.

Any help would be greatly appreciated.

Read other answers

My computer has been generally slow for a while, but suddenly one day it was having a lot of issues. 3 blue screens over the course of two hours despite only using chrome type issues.

I set it up to check the C-drive, restarted to initiate that and went to bed.

The next day it seemed to be fine. The day after that I shut down and when I came back I noticed it was on the log-in screen as if it had restarted instead of shut down. So I logged in and shut it down again.

When I came back the next morning it was very slow to start-up, staying on the initializing screen after log in for 5-10 minutes. When it finally loaded all transparency was gone and it was extremely slow in general. When I tried to check the event viewer I got a "the snap-in is not responding" error and it wouldn't work. I checked for updates and saw there was one for my graphics card so maybe it was a graphics card issue, but the update errors. I tried checking the properties of my C-drive again but every time I right click it windows explorer errors and restarts.

I'm restarting again to see if that helps.

Any help would be greatly appreciated.

A:Multiple errors, 3 blue screens, then general slowness

I'd recommend moving this to the BSOD forum so you get some solid advice to identify the hardware failure.

Read other 1 answers

Recently my Vista install has become very unstable. BSODs are becoming very regular, often occuring within about 5-10 minutes of each other.
I've been having trouble installing games such as Sims 3 and Supreme Commander; they complain of CRC errors when copying the files. However, the discs work fine in other computers, and trying to copy the files to an ISO and mounting it on this computer had the same error, so I don't think it's a DVD Drive problem.

Firefox often shuts down with no error message, it just closes everything. I also often get Vista windows coming up saying 'Superfetch' or 'Host Process and Services' has crashed and needs to shut down.

I've ran a quick scan with Anti-Malbytes which didn't find anything. I've also run chkdsk with /f and /r set on startup, which found no bad sectors or anything on the hard drive.

Does anyone know what could be causing this problem? I'm considering reformatting the drive with either XP or Windows 7, Vista has caused me nothing but problems so far.

I'm running Vista with the newest service pack, and all updates installed.

Thank you.

A:Vista crashing regularly, CRC errors and general depression :(

Read other 16 answers