Over 1 million tech questions and answers.

Windows Updates Not Installing : Error Unknown (Sits on Installing)

Q: Windows Updates Not Installing : Error Unknown (Sits on Installing)

Hi,

To give you some back story, I built my computer the end of August 2012. Ran Smoothly. I decided to get a 60 gig SSD to be the partition that stored Windows. I didnt have much stored on the Main HD so I deleted my original 2TB HD and tried installing on the SSD... found that the SSD was bad and sent it back. Decided just to stick with the 2TB HD. Had some issues installing windows back onto the HD as it would just hang up. Finally managed to get windows installed, had some "Not genuine" issues but that resolved after multiple restarts. That brings me to where I am at today and I feel as though the system has been getting worse. I would normally be fine with just a clean install but with all the issues I had with that initially I am very skeptical of trying it again. I have 5 important updates and 7 optional updates all of which do not install. The Installer just sits on Downloading updates and I have left it overnight with still no result. I am not sure if this is even my main issue but I am beyond the point of figuring it out myself so any help would be appreciated

I downloaded the System Readiness Tool and it Ran. I tried running the sfc /scannow in Admin cmd prompt mode and get a "Windows Resource Protection could not perform the requested operation" I attached my CBS file. Any help you could give or guidance you can provide would be greatly appreciated.

RELEVANCY SCORE 200
Preferred Solution: Windows Updates Not Installing : Error Unknown (Sits on Installing)

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: Windows Updates Not Installing : Error Unknown (Sits on Installing)

Hello and welcome Faticus just as matter of interest why did you give up on the SSD? was not it under warranty?

That is heck of a drive to be installing on mate just how did you prepare it for the install?

You can run a chkdsk in Windows too > My Computer > right click on the drive > Properties > Tools > Check now - then follow the points in my pic.
You then reboot and it will start a chkdsk (in DOS).

Read other 9 answers
RELEVANCY SCORE 82

How do I installing something during the Windows Setup Menu's Installing features and Installing updates? John

A:Installing Updates and Installing features part of windows setup menu

Please correct your sentence. It is not readable.

How do you do what during that phase of install? You don't need to do anything except wait.

Read other 3 answers
RELEVANCY SCORE 80.8

Windows updates keeps installing/reinstalling the same update over and over again. I looked in my update history and it shows that they are installed successfully every time. What should I do and is this using space on my laptop by re-installing over and over again?
 

A:Solved: Windows updates keeps installing/re-installing the same update over and over

It is not using any space. Right-click the ones you already have and hide them so they don't come back.
 

Read other 3 answers
RELEVANCY SCORE 80

when I go to windows update it says 'Windows could not search for new updates' 'Errors found: 800B0001

please help

A:Error installing Windows Updates

also when I try to install windows system readiness tool I get error '0x8007000d

Read other 2 answers
RELEVANCY SCORE 78.8

Please help!

I just bought my computer 2 weeks ago .. I filled in my specs and also uploaded my system info information as an attachment. Last night, I tried to download the windows 8.1 update. I let it run over night, but this morning when I woke, I had a blue screen that said windows could not fix my problem .. and gave me options to try. I ended up having to wipe my computer to factory conditions. After the restore .. the only thing I installed before downloading updates was my driver for my NVIDIA Geforce750 Ti card, and my wireless network adapter ..

I then downloaded 91 updates .. everyone failed .. and every one didn't install .. error 800F0922. I scoured the net and found a suggestion to scan for problems .. I typed ..

sfc /scannow .. got to 51% .. then ..
Windows Resource Protection found corrupt files but was unable to fix some of them. Details are included in the CBS.log windir\logs\cbs\cbs.log. For example C:\windows\logs\cbs\cbs.log. Note that logging is currently not supported in offline servicing scenarios.

I tried to upload the file, but it says I don't have access. I can't even read it because I don't have access .. so I don't even know what the corrupt files are or how to fix them ..

If needed I can list all the KB's .. but 91 will take a good long time to list. I'm hoping someone can tell me what to do! I'm not the tech-savviest, but I'm not drooling at the screen either.

Thanks in advance for your help!

Dex

A:Windows Updates not installing .. error 800F0922

control panel windows updates Troubleshoot, worked for me

Roy

Read other 1 answers
RELEVANCY SCORE 78.8

I keep getting this error, code: 80072F76. My internet is fine and I haven't had problems before. Temporary problem or is there a bigger picture here I am not seeing?
 

A:Solved: Error installing updates, windows 7?

Just started working, maybe it just because its RC.
 

Read other 1 answers
RELEVANCY SCORE 78.8

Attachment 363045 Been having this problem for a while. My laptop has started to BSOD/crash a bit lately and was wondering if this was the problem. Thanks for the help.

A:10 Windows updates not installing Error 80073701

You have obviously run the CheckSUR/SURT tool - please post its logs.
C:\Windows\Logs\CBS\CheckSUR.log and CheckSUR.Persist.log

Here's one of the reasons we need it!

Code:
2015-06-16 08:15:46, Info CBS Exec: Installing Package: Package_30_for_KB2982378~31bf3856ad364e35~x86~~6.1.1.0, Update: 2982378-83_neutral_GDR, InstallDeployment: x86_3e7c4b8a4e0ee119d1049df8294325a0_31bf3856ad364e35_6.1.7601.18270_none_7cd6f84541f36b2b
2015-06-16 08:15:46, Error CSI [email protected]/6/16:15:15:46.877 (F) d:\win7sp1_gdr\base\wcp\componentstore\csd_locking.cpp(324): Error STATUS_SXS_ASSEMBLY_MISSING originated in function CCSDirectTransaction::LockComponent expression: (null)
[gle=0x80004005]
2015-06-16 08:15:52, Error CSI 0000020a (F) STATUS_SXS_ASSEMBLY_MISSING #5335645# from CCSDirectTransaction::OperateEnding at index 0 of 1 operations, disposition 2[gle=0xd015000c]
2015-06-16 08:15:52, Error CSI 0000020b (F) HRESULT_FROM_WIN32(ERROR_SXS_ASSEMBLY_MISSING) #5335530# from Windows::ServicingAPI::CCSITransaction::ICSITransaction_InstallDeployment(Flags = 0, a = 3e7c4b8a4e0ee119d1049df8294325a0, Version = 6.1.7601.18270, pA = PROCESSOR_ARCHITECTURE_INTEL (0), Culture neutral, VersionScope = 1 nonSxS, PublicKeyToken = {l:8 b:31bf3856ad364e35}, Type neutral, TypeName neutral, PublicKey neutral, cb = (null), s = (null), rid = [77]"Package_30_for_KB2982378~31bf3856ad364e35~x86~~6.1.1.0.2982378-83_neutral_GDR&quo... Read more

Read other 8 answers
RELEVANCY SCORE 78.8

Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft® Windows Vista™ Home Basic , Service Pack 2, 32 bit
Processor: Intel(R) Celeron(R) M CPU 420 @ 1.60GHz, x86 Family 6 Model 14 Stepping 8
Processor Count: 1
RAM: 501 Mb
Graphics Card: Mobile Intel(R) 945 Express Chipset Family, 64 Mb
Hard Drives: C: Total - 32651 MB, Free - 5086 MB; F: Total - 238472 MB, Free - 160169 MB;
Motherboard: DIXONSXP, DIXONSXP, ,
Antivirus: AVG Anti-Virus Free Edition 2011, Updated and Enabled.

Recently noticed that since july 2010 my windows update has not been installing the required updates. Gives me an error code 80246008. after trying to install. I have gone to the Knowledge base and tried to solve the problem but to no success. The BITS starts then stops almost straight away. Then keeps giving me this message.
" The background intelligent transfer service on local computer started and then stopped. Some services stop automatically if they are not in use by other services or programs. "

Can anyone help please.
Many thanks.
 

A:Error 80246008. Windows not installing updates

Read other 16 answers
RELEVANCY SCORE 78

I recently wiped my hard drive with dban using the autonuke option. It ran fine and finished sucesfully. I then installed windows 7 home premium x64 on that same hard drive. That also ran fine. I then updated through windows update, and some updates did install, inluding service pack 1. The bsod happens when running automatic updates in windows. It downloads all the updates fine, but when it gets to installing the last few, or at least from what I can tell since the progress bar is almost full, the bsod happens. It says bad pool header 0x019 etc. Malware bytes free trial premium was running while installing the updates.

A:BSOD when installing windows updates, error 0x019

mvac.sys appears to be the issue which is part of malwarebytes. I've never known Malwarebytes causing issues.
It might be due to you have the free trial of premium which we always recommend you disable.

The best option I can think of is to uninstall Malwarebytes altogether and then install it again by following these settings.

Untick the option to start the free trial of malwarebytes pro


Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 19, {20, fffffa8007fa8800, fffffa8007fa8820, 402000a}

Unable to load image \??\C:\Windows\system32\drivers\mwac.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for mwac.sys
*** ERROR: Module load completed but symbols could not be loaded for mwac.sys
Probably caused by : fwpkclnt.sys ( fwpkclnt!FwpsConstructIpHeaderForTransportPacket0+20a )

Followup: MachineOwner

Code:
fffff880`07d38358 fffff800`02bf66d3 : 00000000`00000019 00000000`00000020 fffffa80`07fa8800 fffffa80`07fa8820 : nt!KeBugCheckEx
fffff880`07d38360 fffff880`0172842d : 00000000`00000008 fffff880`00000004 00000000`676e7049 fffff880`02eab0... Read more

Read other 3 answers
RELEVANCY SCORE 78

Hi, I've been trying to update a PC running Win 7 HP x64 to SP1 and it keeps failing giving me the error in the thread title.

I've done all the standard stuff for this error (ran System Update Readiness Tool etc...) and nothing is fixing it.

I've attached the CheckSUR.log to this post. If someone can please help I would be most grateful.

A:Windows 7 Updates Not installing Error TRUST_E_NOSIGNATURE 0x800b0100

Windows permissions are screwed up.Reset registry and file permissions

Windows Repair (All In One)

Read other 2 answers
RELEVANCY SCORE 78

Hi I recently Installed Windows 7 Ultimate 64bit and when updates and SP1 try to install i get this error TRUST_E_NOSIGNATURE(0x800b0100). Please don't tell me to re install windows because i only just did after my old hard drive failed.I found a thread on these forums where somone had a very similar problem. Click Here .So if you have these mentioned files in the attached Checksur.log file please upload them in a zip Thanks.

A:Windows 7 Updates Not installing Error TRUST_E_NOSIGNATURE(0x800b0100

Help!!!!

Read other 9 answers
RELEVANCY SCORE 78

I recently refreshed my Windows 8 installation as I had experienced a problem with graphics drivers which left my PC barely running.


The refresh seemed to go fine, albeit slowly, yet my computer was back up and running as it always had been. However, when I then attempted to reinstall the windows updates and programs I had lost in the refresh, it would fail for all updates with
error code 800F0922. Furthermore, several 3rd party programs would fail to install, citing a 'microsoft.vc80.crt' error.


I was unable, therefore, to update to Windows 8.1 through the Windows Store (as this requires a readiness-for-8.1 update for Windows 8) which required me to update through a disc copy burnt from an .iso downloaded with my key. I had hoped the installation
of Windows 8.1 would fix my problem, however it did not - I am experiencing exactly the same errors with all Windows updates and certain programs.


I have determined from a large trawl of the internet and Microsoft forums that my problem is related to a problem in the installation of .Net Framework 3.5. I therefore followed all given instructions as to turn this feature on and fix it.
When attempting to install .Net Framework reliant products, I receive Error 1935.


Let me be clear in this situation: The following fixes I have tried have all taken place on my recently-refreshed machine both normal and clean-booted, from elevated-level command prompt where applicable and with no 3rd party
anti-virus or f... Read more

Read other answers
RELEVANCY SCORE 78

Custom built my own computer back in May, and everything was working fine, then one day, updates kept failing and failing. I've gone through lots of Microsoft support pages but didn't find anything. I am running Windows 7 Home Premium 64-bit, verified. The OS is loaded on a Kingston v300 240gb ssd if that matters.

What happens is I go to shut down, and it will bring up the updates screen. 1 of 24, 2 of 24, and then it jumps to 14 of 24, then jumps to 24, then shuts down. The error code (after going into the manual updates and seeing why they failed) was 800B0100. Any way to fix this or am I gonna have to re-install the OS?

A:Windows updates not installing, error code 800B0100

Please follow the Windows Update Posting Instructions and post the requested data

If the file is too large (8MB compressed), remove the older CBSPersist cab files until the final file is below the limit - you can always post them separately after zipping them. (the forum doesn't allow the upload of bare CAB files, for a number of reasons)

Please also post the C:\Windows\windowsudpate.log file

Read other 1 answers
RELEVANCY SCORE 77.6

I haven't been able to sucessfully install updates for Trend Micro Security. I tried manually installing, but it didn't take. It also continuously disables my firewall. I ran hijack this. Here is my log... help please! Logfile of Trend Micro HijackThis v2.0.2Scan saved at 11:29:56 PM, on 2/21/2009Platform: Windows XP SP2 (WinNT 5.01.2600)MSIE: Internet Explorer v7.00 (7.00.6000.16791)Boot mode: NormalRunning processes:C:\WINDOWS\System32\smss.exeC:\WINDOWS\system32\winlogon.exeC:\WINDOWS\system32\services.exeC:\WINDOWS\system32\lsass.exeC:\WINDOWS\system32\svchost.exeC:\WINDOWS\System32\svchost.exeC:\WINDOWS\system32\spoolsv.exeC:\Program Files\Adobe\Photoshop Elements 7.0\PhotoshopElementsFileAgent.exeC:\Program Files\Common Files\Apple\Mobile Device Support\bin\AppleMobileDeviceService.exeC:\Program Files\Bonjour\mDNSResponder.exeC:\WINDOWS\system32\lxdncoms.exeC:\Program Files\Common Files\Microsoft Shared\VS7DEBUG\MDM.EXEC:\WINDOWS\system32\nvsvc32.exeC:\Program Files\Trend Micro\Internet Security\SfCtlCom.exeC:\Program Files\Analog Devices\SoundMAX\SMAgent.exeC:\WINDOWS\system32\svchost.exeC:\Program Files\Webroot\Spy Sweeper\SpySweeper.exeC:\Program Files\Cano... Read more

A:Unknown malware? Problems with firewall and installing security updates

Hello Amy,Sorry about the delay. If you still need help, please post a new HijackThis log to make sure nothing has changed, and I'll be happy to look at it for you.The current formatting of your log makes it difficult to read. Please open Notepad:On top, click Format >uncheck Word Wrap.Thanks,tea

Read other 2 answers
RELEVANCY SCORE 77.2

I've been trying to install the anniversary update but it keeps failing. When I attempt through "Check for updates" in settings it finishes downloading/installing then restarts my PC, when it turns back on I get the notification that updates couldn't finish installing. I have tried the Win10 upgrade assistant from Microsoft but it either gives me "Something went wrong 0x80004005 Error Code" or it will continue to download/install and open a window with the dark blue background but then exit and say in a small pop up "Windows 10 update failed."
Any solutions for my problem?

Read other answers
RELEVANCY SCORE 77.2

Hi

I am facing some issues PERSISTANTLY. I am unable to install 7 updates relating to the following (these are latest updates after I check for updates): -

1. Security Update for Office 2003 (KB2817480) => Error details: Code 8007006E
2. Update for Microsoft Office 2003 (KB2543854) => Error details: Code 8007006E
3. Update for Microsoft .NET Framework 4 on Windows 7 for x64-based Systems (KB2468871) => Error details: Code 66A
4. Security Update for Office 2003 (KB2760574) => Error details: Code 8007006E
5. Security Update for Office 2003 (KB2817474) => Error details: Code 8007006E
6. Update for Microsoft Office 2003 (KB2539581) => Error details: Code 8007006E
7. Security Update for Microsoft Office 2003 (KB2288613) => Error details: Code 8007006E

Can somebody PLEASE help me? I have already tried the system update readiness tool, the sfc scannow tool, various microsoft fixits but to no avail... (.

A million thanks in advance!

Macho3001

A:Error Code 8007006E, 66A Problems in installing Updates in Windows 7

Pleasefollow the WindowsUpdate Posting Instructions and post the requested data

Read other 1 answers
RELEVANCY SCORE 77.2

Hey all,
Been tinkering with this laptop, I just installed a fresh copy of W7 Ult, and was looking to put Chinese display language on there. At first all the updates were working out fine, but now I've hit a roadblock...
My language pack doesn't install, and just spits out the 800b0100 error code. No other windows updates install either..
Here's what I did:
Scoured the internet
chkdsk /r
sfc /scannow
Update Readiness Tool
Easyfix 50202
Reset update components
Tried downloading the language pack from a website and installing it that way (both exe, and the lp file)
I feel like I've done everything under the sun and still can't get the thing to install this language pack.
Any advice?

A:Windows 7 language pack / updates not installing (Error 800b0100)!

The 800b0100 error code translates to:

PS C:\> [ComponentModel.Win32Exception]0x800b0100
No signature was present in the subject
Is this a legitimate copy of Windows? Please provide me with an MGADiag report.
Download and save MGADiag from here.
Navigate to the directory where you saved the file.
Right-click on MGADiag.exe, select Run as administrator, and accept any User Account Control prompts.
Click Continue.
Click Copy.
Paste the copied information in your next reply.

Read other 5 answers
RELEVANCY SCORE 75.6

I have 3 Updates I've been trying to install for a while, however they seem to keep failing. I've never had any issues previously with Windows Update, and I keep the computer relatively clean. I've tried a few troubleshooting steps ( Such as running my Registry Cleaner, Fix-its from Microsoft )

I am getting the Error 80070643. I ran the Fix-it from the Microsoft Website - Windows Update error 80070643 and the Microsoft Office Source Engine Service is already running.
I also went here, and ran the Fix-it which resets Windows Update, In Aggressive Mode - How do I reset Windows Update components?

Ran Windows Update again, Same error.

I’m running Windows Seven x64 Home Premium, I have not made any recent changes to my computer.


Either the Updates are bugged, or there's something else going on here. I'm going to try installing them from the Administrator Account - I am going to try in Normal Mode and In Safe Mode With Networking and post back the results. If anyone has any suggestions I'd be very grateful. Thanks

I've honestly never really had an issue with Updates. This is very odd.


**I tried Windows Update on Administrator with no success. I also tried to run it in Safe Mode, but it would not open.**


I'm going out - I will be back later.

A:Windows Update Error 80070643, Installing Updates for MS Office 2003 S&T Edition.

In this article You receive an "Error 80070643" error message when you try to update Office 2003 by using Software Update Services
there are more offered solutions

Read other 6 answers
RELEVANCY SCORE 72.4

When I try to install KB3182373, a "Security Update for Microsoft Silverlight", Windows Update reports failure with the message "Code 643 Windows Update encountered an unknown error".
I ran WindowsUpdateDiagnostic.diagcab. It reported that "Troubleshooting couldn't identify the problem".
What can I do to fix this? I'm running Windows 7 Professional.

Read other answers
RELEVANCY SCORE 72

My friends PC was having trouble booting due too a Shell32.dll file being missing apparently??

Well he bought a new one rather than get it repaired and gifted me the old one as I said I could maybe fix it for myself as its a decent PC!!

My answer was just to install XP again, clean install not repair, problem is everytime I run the disc after the files load I get and error message saying "Unknown Hard Error" on a blue screen and it goes no further!! :(

I tried another hard drive and exactly the same thing happened, I tried reseting all to factory defaults settings in the setup, still the same and I'm stumped!!

I Googled the life out of it but haven't found any solution other than suggesting there could be a conflict between the PC and a Zip Disc drive but this machine never had one installed at any point!!

Can anybody assist here, I would be grateful for the help!! :)

A:[SOLVED] Help Installing XP - Unknown Hard Error

Did you disconnect all external peripherals except the monitor, keyboard and mouse, and be sure those are not USB, or wireless. Any internal USB card should also be removed.

Read other 9 answers
RELEVANCY SCORE 71.6

Windows is unable to install latest KB2532531, KB2533623, KB2555917 error configuring...reboots and then keeps asking again and again because of auto update. please help!

A:error installing updates

I have the same problem.

Read other 2 answers
RELEVANCY SCORE 71.2

someone used my laptop and downloaded a mp3codec.exe and installed itafter that i've been getting error msgs like whenever i try to move from one document to another in explorerthis is my hijackthis log:Logfile of Trend Micro HijackThis v2.0.2Scan saved at 10:49:55 PM, on 1/9/2008Platform: Windows Vista SP1 (WinNT 6.00.1905)MSIE: Internet Explorer v7.00 (7.00.6001.18000)Boot mode: NormalRunning processes:C:\Windows\system32\Dwm.exeC:\Windows\Explorer.EXEC:\Windows\system32\taskeng.exeC:\Program Files\Windows Defender\MSASCui.exeC:\Program Files\Intel\Intel Matrix Storage Manager\IAAnotif.exeC:\Windows\RtHDVCpl.exeC:\Program Files\Common Files\Symantec Shared\ccApp.exeC:\Program Files\Synaptics\SynTP\SynTPStart.exeC:\Program Files\Acer Arcade Deluxe\Play Movie\PMVService.exeC:\Acer\Empowering Technology\eDataSecurity\eDSLoader.exeC:\Program Files\ATI Technologies\ATI.ACE\Core-Static\MOM.EXEC:\Users\ping\AppData\Local\Temp\RtkBtMnt.exeC:\Program Files\Launch Manager\LManager.exeC:\Program Files\Synaptics\SynTP\SynTPEnh.exeC:\Acer\Empowering Technology\eAudio\eAudio.exeC:\Program Files\Java\jre1.6.0_07\bin\jusched.exeC:\Program Files\Razer\Diamondback\razerhid.exeC... Read more

A:Critical Error Msg After Installing Codec From Unknown Source

Hello, pingz. to BleepingComputer.comMy name is Billy O'Neal and I will be helping you. (Billy or Bill is fine, if you like.)I want to apologise that it has taken so long to get back to you. We on the HJT Team are working as fast as possible to get your log answered.If you would still like help, please post a new HiJack This log below, as things may have changed on your system.If you do not still need help, please let me know, so that I can move on to other users who still need help.Please take note of the following:While a HJT Team member is working with you, please refrain from making any changes to your computer.Also, even if things appear to be running better, there is no guarantee that everything is finished. Please continue to check this forum post in order to ensure we get your system completely clean. We do not want to clean you part-way up, only to have the system re-infect itself. If you do not understand any step(s) provided, please do not hesitate to ask before continuing. I would much rather clarify instructions or explain them differently than have something important broken.Please reply using the button in the lower left hand corner of your screen.Old topics are closed after 3 days with no reply, and working topics are closed after 5 days. If for any reason you cannot complete instructions within that time, that's fine, just put a post here so that I know you're still here. We get a lot of people who simply leave, and if there is no contact for that amount of ... Read more

Read other 15 answers
RELEVANCY SCORE 71.2

I just bought my PC yesterday and I've spent at least an hour today trying to install google chrome. It will download every time I try but when I press run on the tab at the bottom of the screen it will try to install then when it is finished it says google chrome could not install due to an unknown error. I have tried restarting my laptop, downloading both the 64 bit and 32 bit versions for windows 10 and nothing has changed. Each time it just won't install due to an "unknown error." Please help, I have been using chrome for years and everything I use is run through google.

Read other answers
RELEVANCY SCORE 70.8

I have a very common error. I did a Google, search for the error. It seems like a lot of others has this error. I will post my error below. I get this error when trying to install .exe programs. For example. I tried to install IrfanView. I get an error. I tried right clicking, then properties, then click on unblock. It didn't work. Some or most say unblock will work. In my case it didn't. This just recently started after new updates. I guess it's a new error by MS?
Windows cannot access the specified device, path, or file. You may not have the appropriate permissions to access the item.
I am the administrator of this PC.
 

A:XP error while installing .exe files after MS updates

Is the exe not running or when the exe starts 'it' can't get to the path? Are you installing locally, network drive, or install across the internet?

Are you running IE7? before this started?

Are you logging in as Admin? or is your user a member of the admin?
 

Read other 1 answers
RELEVANCY SCORE 70.8

Error installing driver updates

Open Gateway site map. Click on “My Down loads” under “Drivers and Downloads”. A page opens up and I select my operating system – Windows XP. A page opens up showing 10 or 12 driver updates. I click on the first one and a page opens up showing buttons for download instructions and install instructions. I download the first update to my desk top and an icon shows up there. I click on it nothing happens or I get an error message.

C:\Cabs\d20003-003 refers to a location that is unavailable. It could be on a hard drive on this computer or on a network. Check to make sure that the disk is properly installed, or that you are connected to the Internet or your
Network, and then try again. If it still cannot be located, the information might have been moved to a different location.

I intrepid this as meaning some files were missing so I ran Scannow and it didn’t find anything wrong

If some one can help it would be greatly appreciated.

Thank you.

Jim
 

A:error installing driver updates

C:\Cabs is the default folder where Gateway drivers extract to when you unzip them. It has nothing to do with Windows, that is why scannow didn't find anything. Either the driver installer is expecting the folder to already be there, or is unable to create it. Do you have problems installing any other software on the C drive?
 

Read other 3 answers
RELEVANCY SCORE 70.8

For a while now (several months) I am having trouble installing windows updates. An example:

Error Code 800F0922 when installing a safetyupdate (KB2736693) for Microsoft.NET framework 3.5 on windows 8 and windows server 2012 for x64-systems.
But then when installing a different safetyupdate (KB2742616) it doesn't give me an error.
I also get error configuring updates from time to time after I update while restarting or shutting down.
I think the problem has something to do with writing permissions, because I can't install microsoft office 2010 either. When trying to install microsoft office it only installs it partially, after which it says that I don't have the privileges to write something to my E drive.

Any help would be appreciated!

Alex

Read other answers
RELEVANCY SCORE 70.8

Since installing a bundle of updates last week (I'm not sure it that's related or not, but that happens to be when this started), I've been getting an error everytime I start the computer. I've attached a snip of the error. It seems it's an error opening an HTML file called "dnserrordiagoff_weboc". I have no idea what this is or why it's trying to open it. I looked to see if it was just a random thing that was added to my startup, but there's nothing in the startup folder.

What is this and how can I get rid of the error?

Any help would be so appreciated; it's very annoying!

A:Startup Error Since Installing Updates

Try removing update KB942615See if that helpshttp://support.microsoft.com/kb/942615

Read other 1 answers
RELEVANCY SCORE 70.4

I'm having trouble with installing my updates my computer says that needs to be installed every time I install them and restart my computer it says update failed to install PLEASE REPLY IF ANYONE HAS ANY INFORMATION
 

Read other answers
RELEVANCY SCORE 70

hello

i have been getting the 8007010B error when trying to install updates. what can i do to fix this. thanks you.
 

Read other answers
RELEVANCY SCORE 70

Every time I try to install update -Microsoft Office 2007 Service 1 update, I keep getting error code 80070663. I have tried every time I am notified of this update but every time fails with this error code. Have checked through the Microsoft website help sections but can find nothing for this error code.
 

A:Error Code 80070663 installing updates

hi i have looked through what is available via ms and other forums and it involves a good deal of registry edits if you wish i can get you links to them or a possibly easier option would be to uninstall and reinstall office
 

Read other 1 answers
RELEVANCY SCORE 70

IoGear GBU321 USB to Bluetooth device.
Prior to downloading updates my USB - Bluetooth device worked great after the 89 updates then the 5 updates which one was Windows 7 64 Bit service pack 1, my device stops working.
Here is what pops up when i try to use it:
BTWUIEtx has stopped working.
-> Check online for solutions and close program.
-> Close program.
Of course I checked for online solution and nothing happens it just closes the program. I need this Bluetooth adapter to work. My only solution at this point is reinstalling the O.S. and not letting any windows updates in.
Anyone have any suggestions???

A:IoGear GBU321 gives an error after installing updates.

Hi repinscales

I have an IO Gear GBU421 and it's working fine under Windows 7 x64 SP1 and all other updates.

I would suggest you completely uninstall the IO Gear software and try reinstalling it again. Don't use the drivers from the disk you have get them here - Drivers & Manuals - IOGEAR

Here's a warning for my adapter - IOGEAR TIL Document # 328. Not sure this applies to you but it's something to take note of.

You could also try using the Broadcom drivers as discussed here.... Latest Broadcom Bluetooth Driver

Let us know.

Read other 3 answers
RELEVANCY SCORE 70

The last 2 or 3 times I've tried to install daily updates to my system, which runs Windows XP Pro, I have been receiving the following error message,

error creating process <c:\docume~1\DAD~1\LOCALS~1\Temp\IXP000.TMP\dahotfix.exe /q/n>. Reason: The system cannot find the path specified.

and then the update install is aborted.

Before I did a system restore to see if I could fix this, I figured I'd give it a shot here to see if anyone else has ever had a problem like this.

Thanks a ton for any suggestions.

v/r
 

A:error message when installing daily updates to XP Pro

Read other 14 answers
RELEVANCY SCORE 69.2

This is the message I get: Read more about steps you can take to resolve this problem (error number 0x8DDD0007) yourself.

I did the following:
1- Rebooted
2- check for the registry key
"HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\Cur rentVersion\WindowsUpdate\Auto Update\RebootRequired" but doesn't exist.
3- Re-register Windows Update components and Clear the corrupted Windows
Update temp folder, which involved:
a. Click on Start and then click Run,
b. In the open field type "REGSVR32 WUAPI.DLL" (without quotation marks) and
press Enter.
c. When you receive the "DllRegisterServer in WUAPI.DLL succeeded" message,
click OK.
d. Please repeat these steps for each of the following commands:
REGSVR32 WUAUENG.DLL
REGSVR32 WUAUENG1.DLL
REGSVR32 ATL.DLL
REGSVR32 WUCLTUI.DLL
REGSVR32 WUPS.DLL
REGSVR32 WUPS2.DLL
REGSVR32 WUWEB.DLL
After the above steps are finished reboot.
Since temporary folder of Windows Update may be corrupted. We can refer to
the following steps to rename this folder
a. Click Start, Run, type: cmd and press Enter. Please run the following
command in the opened window.
net stop WuAuServ
b. Click Start, Run, type: %windir% and press Enter.
c. In the opened folder, rename the folder SoftwareDistribution to SDold.
d. Click Start, Run, type: cmd and press Enter. Please run the following
command in the opened window.
net start WuAuServ

Still nothing

ANy ideas??
 

A:Updates not installing or working (error number 0x8DDD0007)

Read other 11 answers
RELEVANCY SCORE 69.2

Okay so when I try to install updates, I get an error after about 11% of the download. It says: "Some updates were not installed
"Failed: 4 updates"
"Error(s) found:"
"Code 80070426 Windows Updates encountered an unknown error."
I'm been researching but couldn't find anything that would help my situation. I also saw a lot of "reformatting would be the best option"
- Problem with that is, it's my brothers laptop and I don't believe it came with a Vista disc. So if there was a way to avoid reformatting that would be great. Please help

If this is any use:
Windows Vista Home Premium
Service Pack 1
Manufacturer: Hewlett-Packard
Model: Presario F700 (GR967UA#ABA)
Processor: AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55 1.80 GHz
Memory: 1.00 GB
System Type: 32-bit Operating System
Thanks for your help.
 

A:When installing updates with Vista - Error Code 80070426

Read other 16 answers
RELEVANCY SCORE 69.2

I am attempting to correct an issue with Windows stating my copy is not genuine, I am also unable to install Windows updates, which I presume is part of the same issue. What I've done so far: I was able to run slui 3 and enter my key from the sticker and it was accepted. Thought maybe this solved issue but still can't update. Ran chkdsk /r and scannow. Both completed, with scannow giving the message: "Windows Resource Protection found corrupt files but was unable to fix some of them." Ran the MS tool to correct update issues. Says it fixed the issue but installation of updates still bombs out. Finally I found a post elsewhere about removing KB971033 so I did that...of course I noticed in other posts here that that wasn't a great idea. Unfortunately with my inability to run Windows Update, I can't correct that now.

I just ran the MGDiag tool and results are below:


Code:
Diagnostic Report (1.9.0027.0):
-----------------------------------------
Windows Validation Data-->

Validation Code: 0
Cached Online Validation Code: 0x0
Windows Product Key: *****-*****-THYYK-MHBDT-739P8
Windows Product Key Hash: dDCkIhW0lnoeNA3wJbq5zK2SQqc=
Windows Product ID: 00359-OEM-9800803-90283
Windows Product ID Type: 8
Windows License Type: COA SLP
Windows OS version: 6.1.7601.2.00010300.1.0.003
ID: {6E63D7A3-7900-4F5A-B10E-DAB9ABB9FD9D}(1)
Is Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/A, hr = 0x80070002
Signed By: N/A, hr = 0x80070002
Product Name: Windows 7 ... Read more

A:Genuine Validation Error - Installing Updates Fails

Please open an Elevated Command prompt and run the following command

Regsvr32 wintrust.dll

You should get a 'Succeeded' popup - if not, please detail the EXACT error.



Here are some instructions to make life easier
1) To open an Elevated Command Prompt Window (the ECP window), click on Start, All Programs, Accessories – then right-click on Command Prompt, and select Run as Administrator. Accept the UAC prompt.
2) To run the commands easier, highlight the block of commands, and right-click on the highlight – select Copy. In the CP Window, click on the black/white icon at top left – select Paste. The commands will run but may not complete the last command, so hit the Enter Key once.
3) To copy the results... click on the Black/White icon in the top left, and select Edit... 'Select All', and hit the Enter key - then use Ctrl+V or r-click+Paste to paste it into your response.

Read other 9 answers
RELEVANCY SCORE 69.2

So yea, today i was surfing the net then I decided to close my laptop then I saw that it needed a shut down and needed to update some vista stuff. So I clicked shutoff then the updates started and ended.
Then after a few after dining, I wanted to go on my laptop so I started it, the updates started and then was stuck at 25% for like 30 minutes so I decided to force shutdown.
After forcing shutdown, I restarted the laptop, then it brought me to the Windows Error Recovery.
(Safe mode, Safe mode with networking, Safe mode with command Promt, Last known good config, Start Windows Normally )
I tried em all and it still brought me to that blue screen of Death. ( the Blue screen appears too fast and shut down quickly for me to read what it says )
Then it restarts and do the same thing again and again

I lost my Vista premium CD and all. What to do?
I got a eurocom M860TU laptop.
 

A:Blue screen Error after installing Vista updates

Hi this may help yiu run a repair http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/

method 1 http://www.bleepingcomputer.com/tutorials/tutorial148.html

method 2 http://www.vistax64.com/tutorials/88236-repair-install-vista.html
 

Read other 3 answers
RELEVANCY SCORE 68.4

Hi,
Failed system. SP1 rolled back ...
Update Center -> Start Manual Search.
Result: it was found a new update KB976932 (SP1). The attempt to establish results in an error: 80070490
I run:

Code:
sfc /scannow
Then I use a utility System Update Readiness Tool What is the System Update Readiness Tool? - Windows Help

I archived two files for the analysis:
C:\Windows\System32\config\COMPONENTS
and
C:\Windows\Logs\CBS\CheckSUR.log

Microsoft services

I'm very sorry, COMPONENTS.ZIP have a size ~ 15M

P.S.: Forgive for bad knowledge of English. I very need your help.

A:Fault system updates - Error 80070490 when installing KB976932 (SP1)

You have fairly massive registry problems...

Code:
Summary:
Seconds executed: 737
Found 782 errors
Fixed 1 errors
CBS MUM Missing Total count: 7
CBS MUM Corrupt Total count: 3
Fixed: CBS MUM Corrupt. Total count: 1
CBS Registry Error Total count: 1
Fixed: CBS Paired File. Total count: 1
CSI Missing Winning Component Key Total count: 771
I really think your best option is going to be a repair install - or a Clean install.

Read other 1 answers
RELEVANCY SCORE 68.4

I am running Windows 7 64-bit on an Alienware M14x.

Okay, let me list out all the problems.

It will not install updates correctly, meaning it will reboot two times before it says, "failure to update, reverting changes" and allow me to log into my computer. Sometimes it will take 15 minutes per "Configuring Windows, please wait" screen.

It is also not allowing me to download Microsoft Office 2010. I keep getting this error code:
Error 1935. An error occurred during the installation of assembly component {A75F2217-AD54-3EA6-AE14-F255F8660531}. HRESULT: 0x8007054F.

And none of the updates are sticking.

Every time I close out of Windows Update after installing a Security update, it says there are updates available, and it's another Security update. wtf? Also, I get the error code "Code BC9, Windows Update encountered an unknown error" when it tries to install Internet Explorer, so that doesn't install either.

I did a diagnostic test, and nothing came up as an actual system error, so it's just all Windows itself.

Here is the HijackThis log.
Pastebin

Edit: I ran a full scan on Microsoft Security Essentials and it found a trojan and two other issues. I promptly removed them. However it still didn't repair my update issues (which might be due to a connectivity problem) or my Microsoft Office 2010 problem.
 

Read other answers
RELEVANCY SCORE 68

Basic System Specs:

- x86 (32-bit) or x64 ? x64
- the original installed OS on the system? No, shipped with Vista, upgraded to 7.
- an OEM or full retail version? Full Retail Verison


- What is the age of system (hardware)? Three years, one month, and 11 days old.
- What is the age of OS installation (have you re-installed the OS?) Around one month old.

ZIP folder with PERFMON HTML file and Windows_NT6_BSOD_jcgriff2 folder attached.

OK,

I'm a total noob on this forum, so I tried to follow the instructions on posting.

Firstly, when you read PERFMON, it'll say my HDD is failing. I know that. I know it's stupid to use a failing HDD, but my data is backed up, and I get my Mac on Saturday. Anyways,

Last night, around 1:30 AM, I got up to shut down my computer, it was on, and in the same room as me, and I wanted sleep. So, I went to the start menu, and saw the update icon next to shut down. I shut down the machine instead of sleeping, so it could update. I turn off the monitor to go to sleep. I then hear the fans ramp up, then slow down, and the computer "click" like it does when it shuts off. But, the fans were still running. I turned on a lamp, and sat down. I turned on the monitor, to be facing a big fat BSoD. It didn't give me an exact message of what happened, just a STOP error code. The STOP error code was 0x0000001e, and the BCCode is 1e. I haven't installed any new hardware, and the only software I've installed was Apple's AirPort Utilit... Read more

A:Random BSOD at night, error 0x0000001e, Updates possibly installing.

Failing hard drives can cause BSOD's. But most importantly - they can die without any notice at all. Backup all your stuff immediately!!!

Win7 doesn't like wireless USB devices. You have a Compact Wireless-G USB Network Adapter with SpeedBooster ver.2
Here's my rant about these devices:





Quote:
I do not recommend using wireless USB devices. Especially in Win7 systems.
These wireless USB devices have many issues with Win7 - and using Vista drivers with them is almost sure to cause a BSOD.
Should you want to keep using these devices, be sure to have Win7 drivers - DO NOT use Vista drivers!!!
An installable wireless PCI/PCIe card that's plugged into your motherboard is much more robust, reliable, and powerful.


The memory dump points to networking stuff - and your networking drivers (both wired and wireless USB) are from 2008. This means that it's most likely that the wireless USB drivers are causing the error (although the wired drivers are suspect also).

Please update all of your networking drivers. Be sure to use ONLY Win7 compatible drivers.

Further info on BSOD error messages available at: http://www.carrona.org/bsodindx.html

The following info is just FYI, I've already addressed the issues that I saw in the above paragraphs:
3RD PARTY DRIVERS PRESENT IN THE DUMP FILES
- Create a System Restore Point prior to doing any of this. DO NOT mess with the drivers themselves - leave the Windows\System32\drivers directory alone unless we s... Read more

Read other 9 answers
RELEVANCY SCORE 67.6

Hi Everyone!
My Windows Vista updates arent installing. Whenever i try to manually update it, it gives the following error:
Windows could not search for new updates
Errors found:
Code 800736B1

Any help please?!!! Thank You!

 

A:Windows Updates not installing

Read other 6 answers
RELEVANCY SCORE 67.6

hi Guys... I last night did a repair install of windows XP after having graphics driver problems, new installation works well, but after downloading critical updates(89 of them) it will not instal them. I have tried again, retried, tried installing one at a time, both with firewall and virus sofware on and off... the ambiguous message I get from windows upon failure of installation is... something on your computer is stopping update instal..etc.. well DUR!!! smiles... can anyone point me in the right direction?? oh.. and I use second life.. even with all drivers working, second life refuses to load, saying that my graphics drivers are not up to date or supported, even though they worked fine until 2 days ago... sorrry for the long post.. I'm patiently trawling my way through every piece of advice I can get... ty in anticipation.. Huskym6

A:Windows XP not installing updates

hello

now this is just for starters

now what i need to do is go to your (device manager)

now once there you will want to select from the toolbar of the window(veiw) then a drop down menu / from it you will select (show all hidden devices)

now if you see any (red or yellow) quotation marks , make a note of what they

now go to the (event veiwer) this is thru the (administrator tools) in the control panel
here you will find 3 to 4 subcatagories

you will want to check each of them for this is where windows keeps track of all errors
now you will want to make notes of the errors that have been recorded ( you do not have to make notes of double entries just of the dates of their happenings & how many there is)
you will get more information on the errors if you (right) click them / then select properties

------------------------------------
also
------------------------------------

do you have a Windows Xp cd, not the restore cd's that come with some systems, the cd will have the Windows logo & 3D hollowgram/image on it

if you do not maybe you can barrow one from a friend/family member/co-worker as long as it is the same version that is on your system

if you have (Windows XP Home Ed. sp2 ) then the cd will have to be that / if you have a cd with (Windows XP Home Ed. )you will have to slipstream (SP2 ) onto a disk that you create

this also applies to (Windows XP Professsional )

http://www.helpwithwindows.com/Windo...p2-bootc... Read more

Read other 1 answers
RELEVANCY SCORE 67.6

I just downloaded and installed windows xp home updates on my computer. After installing, my computer restarted itself and now I can't log in. After I enter my password it says loading my settings and then promptly logs me off. I cant even log in from safe mode.

A:cant log on after installing windows updates

Hello and Welcome to TSF,

Do you have a genuine copy of xp home windows cd for the pc?

Read other 1 answers
RELEVANCY SCORE 67.6

I am having issues with installing updates on Windows 7 x64. The start menu always has "Shut down and install updates", I click to install and sometimes the system says installing and then just hangs and sometimes it says it has installed the 2 updates. However when I turn the machine back on the same "Shut down and install updates" message is there. This has been going on everyday for the best part of 6 months.

Any suggestions please?

Many thanks!

A:Windows 7 not installing updates

Hello,

Try deleting the old updates and trying again, Delete Windows update files to regain hard-drive space - CNET, as sometimes this can force computer to hang.

Also try installing your updates through control panel, and see how that works.

Read other 2 answers
RELEVANCY SCORE 67.6

i just got a used quad desktop, i think it has a fresh windows 7 install, as one of the updates was sp1 : windows keeps installing new updates ? is this normal ? i bought this computer 5 days ago, been through about 3 rounds of updates; i was playing a game yesterday when i had told the windows message to postpone the update installation for the max of 4 hrs, i got a blue screen during the game, i don't know if it was the game or the postponed updates; the computer seems fine , other than this situation; call of duty 4 (demo) crashed once, i restarted it in safe-mode and seems ok; what can i do ? thanks

A:windows keeps installing updates ?

how do i 'uninstall installed updates ' ? i checked the control panel, uninstall section , i didn't find any 'installed updates' ? windows keeps trying to install updates; discussion from google seach said to uninstall installed updates, then re-install 64-bit version of updates kb2647753; i can't find the installed updates, to uninstall them, before i install kb2647753 ? thanks

Read other 2 answers
RELEVANCY SCORE 67.6

Gudday all
A few weeks ago I noticed 2 issues with my Windows XP Home.
1. The Window firewall warning comes up that the firewall wall is turned off despite being turned on when going to it. Eventually (5-7 mins) the warning disappears. This occurs everytime we turn the computer on.
2. We have 6 updates that always come up as needing to be installed but when we try to install the updates the computer wanders of to do it. Eventually it returns the message that these updates could not be installed.
The updates areKB975958
KB972580
KB973443
KB734475
KB974554
KB973705
If there are extra updates (i.e. > these six) the extra ones are installed successfully.
I have tried a few times to install these updates.
The computer is a desktop with XP SP3.
I also have a latop with XP Pro SP3 but have not noticed all of these issues.

I have the setting of 'Download updates, but let me choose when to install them'.

Is there anywhere in Windows that might suggest why these updates are not being installed?
I have had a look at Microsoft support pages but a search revealed nothing (I was not really sure how to phrase the question which might have make the search next to impossible).

Has anyone had this problem or similar and any suggestions? A virus has crossed my mind.

A:Windows updates not installing

I had this problem a few times before and have managed to solve it by downloading Microsoft Fix it 50199 from the website
http://support.microsoft.com/kb/299357
You may also try these websites
http://support.microsoft.com/gp/cp_fixit_main#tab0
http://blogs.technet.com/fixit4me/default.aspx
Good luck to you.

Read other 1 answers
RELEVANCY SCORE 67.6

Recently I booted up an old Windows 7 PC which has not been updated since February. I tried to search for updates to install them, but Windows will not search for updates. Other Steam users reported the same issue as well. It seems that Microsoft is intentionally nerfing Windows 7 to get people to upgrade to Windows 10. If that's the case, should I just retire Windows 7 and upgrade the old machine to Windows 10? I know that Windows 10 will update much faster and boot faster as well, but will I run into any issues with drivers on outdated hardware? I have a bunch of bloatware, such as Cyberlink PowerDVD, which I really don't need anymore. My parents will be using it at their residence and I will be using it from time to time during visits. Specs:

Model: HP Pavilion Elite HPE-580T
CPU: i7-950 @ 3.07 GHz
Mobo: Pegatron X58 (Truckee)
RAM: 12 GB @ 1333 MHz
GPU: GTX 660 SC
HDD: OCZ ARC 100 series 120 GB SSD + Seagate Barracuda 1.5 TB HDD
PSU: Corsair CX600M
OS: Windows 7 Home Premium 64-bit

A:Old Windows 7 PC not installing updates

Both pc seem to be reasonably up to date so there should be no problems with win 10 time is running out so I would update as soon as possible you can always role back if you need to us the download its faster and gives you more control https://www.microsoft.com/en-gb/soft...load/windows10

Read other 0 answers