Over 1 million tech questions and answers.

XPS 13 (9343) - Unable to upgrade to Windows 10 - Error 0xC1900101 0x30018

Q: XPS 13 (9343) - Unable to upgrade to Windows 10 - Error 0xC1900101 0x30018

I have a brand new XPS 13, 9343 model with i7 processor and 512GB SSD. I am still within the 14 day cooling off period, and I'm now seriously considering returning it. I have never experienced such a load of nonsense trying to install any other piece of software.
So far, and after many attempts, I've been totally unable to upgrade to Windows 10. The very first thing I did was install all available Windows updates for 8.1 (there were 79 of them), and immediately after that I began the Win10 install saga. Nothing else has been done to the laptop - no dodgy software or USB devices (other than the boot USB where necessary). It is in a clean state.
- After downloading through Windows Update, the installation procedure is INCREDIBLY slow (eg it takes 36 HOURS to reach 42% completion - and at this point it hits the error message). What on earth can it be doing??
- I also tried creating a bootable USB through the media creation tool. If I boot from this USB drive and perform a "clean" install, this works perfectly - it takes about 8 minutes in total (which emphasises how ridiculous the 36 hours is). However, because it is a clean install and not an "upgrade", I end up with a non-activated version of Windows 10 and I get prompted to pay £99.99, which I have no intention of doing. I paid for the laptop on the understanding it would get a FREE upgrade to Win10!
- I have also tried using the USB (but not booting from it) to perform the in-place upgrade - this hits the same error as Windows Update does (and takes just as long)
- I have tried uninstalling all antivirus software and disabling all wireless/bluetooth devices before attempting the upgrade - none of this helps. Given that it takes me 36 HOURS per attempt, it's really not acceptable to try disabling random things in the vain hope it might work correctly.
When attempting the upgrade (i.e. not clean installation), I hit an error message "Windows Setup cannot configure Windows on your hardware" or similar. When resuming after the failure, the setup tool gives the error code 0xC1900101 0x30018, and says it failed in operation "FIRST_BOOT", phase SYSPREP. Just getting to this error message costs me 36 hours of waiting (welcome to the future!), so it would really help if someone could give a definite answer on what causes it...
Please help! Auuughhh

RELEVANCY SCORE 200
Preferred Solution: XPS 13 (9343) - Unable to upgrade to Windows 10 - Error 0xC1900101 0x30018

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: XPS 13 (9343) - Unable to upgrade to Windows 10 - Error 0xC1900101 0x30018

Hi Everyone,
If you are experiencing the issue whereby your XPS 13 is not upgrading to Windows 10 and is getting stuck or taking several hours, PM me with your Service Tag.
Thanks

Read other 55 answers
RELEVANCY SCORE 141.6

Please help,
I have a a XPS 13, 9333 originally delivered with Ubuntu but I need to run Windows 10on it.
So far, and after many attempts, I've been totally unable to install Windows 10. I am subscribed to MSDN so i downloaded the Win 10 installer with a new registration key.
Trying to install Win 10 booting from USB stops midway (black screen for hours).

I was able to install windows 7. Then I tried to upgrade to Win 10 running setup from it.
1st phase (file copying) OK.
2nd phase (driver installation) halts at 25% (40% total) and reboots recovering windows 7 and showing Error 0xC1900101 0x30018 t failed in operation "FIRST_BOOT", ... SYSPREP at startup.
Windows 7 installation from which I start is a clean one, no AV, no apps, nohing.
Any idea anybody?

Thanks
Stefano

A:XPS 13 (9333) - Unable to upgrade to Windows 10 - Error 0xC1900101 0x30018

sspelta,Below is a link for driver installation on your laptop. There is a driver install order that must be followed.Drivers Install Order and Tutorialshttp://dell.to/2guAvnE

Read other 1 answers
RELEVANCY SCORE 114.8

Hello to all,

bought a new Sattelite Pro C850-1MX (PSCBZE 00M009GR) in december 2013. System is running almost unchanged to delivery state. Yet installed OpenOffice, Firefox and AdobeReader in most actual versions. And updated driver for AMD-GPU to latest version. No other changes done.

Now tried to upgrade to Windows 8.1 via Windows-App-Store. Download was done, upgrade run, reboot, installing changes, preparing devices --> reboot, rollback to 8.0 with error code 0xC1900101-0x30018.

Searched internet for solutions: Toshiba sais
- update all Toshiba-components via TOSHIBA Service Station --> done
- (Link: [http://www.toshiba.de/innovation/generic/windows8_1-upgrade-stepbystep/]): deinstall some components: esp. LAN/WLAN-driver.

Hmmm...if I do so I cannot access Windows App-Store to rerun the upgrade because i have no network-connection. Stupid...

- Why can?t I upgrade an almost unchanged system because of some driver-uncompatibilities where i didnt change anything from delivery state???

Please state any hint/solution. Thanks!
Mark

A:Satellite Pro C850-1M - upgrade to Win 8.1 fails - error 0xC1900101-0x30018

>Now tried to upgrade to Windows 8.1 via Windows-App-Store. Download was done, upgrade run, reboot, installing changes, preparing devices --> reboot, rollback to 8.0 with error code 0xC1900101-0x30018.

This error message appears because of some not compatible drivers and tools which are already preinstalled on Windows 8 system.

This issue has been reported many times here in the forum and was solved as reported by user harrie_1 at 12-Jan-2014
Look into this thread: http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=74631

Check what drivers has to be uninstalled in Appendix A
[How to Update from Windows 8 to Windows 8.1|http://support.toshiba.com/sscontent?contentId=4003162]

+What important is to remove the internet connection.+
+Only use to download 8.1 then disconnect (also Lan cable)+
+After starting Win 8.1 for the first time do not connect to the internet.+

+On another pc download first the drivers for 8.1 audio,realtek wlan and bluetooth and display driver.+
+Install and restart after this when de system is stable you can connect to internet and download the windows updates.+

PS: this thread should be closed to avoid misunderstandings and because other thread already exists

Read other 2 answers
RELEVANCY SCORE 113.2

Hey guys,

I've been having a problem with upgrading to Windows 10. I've tried using the tool both by running it on my PC and putting it on a USB. It gets through the first part of copying files and does the first reboot, then it starts back to the screen and the Installing Features and Drivers sits at 0% for a few seconds then resets and restores my old version with this error:

0xC1900101 - 0x30018 - The installation failed in the FIRST_BOOT phase with the error during SYSPREP operation.

When I originally looked this error up I read that it might be an encryption error so I decrypted both of my drives, ran the install again.. Same error. So now I am at a complete loss as to what to do so I can get myself upgraded.

System:

Windows 8.1 Pro x64
Mobo: ASUS ROG Maximus VII Hero
PCU: Intel i7 4790k 4.00 GHz
GPU: ASUS ROG MARS760x2 (2 GTX 760 chips on one card)
RAM: 16GB DDR3

Please let me know if you have any info or advice as to how I can fix or workaround this issue.

Thanks,

Hoffmann

A:Windows 10 Upgrade Failure - 0xC1900101 - 0x30018

I am having exactly the same problem, I am installing from USB onto Windows 8.1 Pro, as the administrator (local) outside of the normal domain. It gives no warning of this error until it has been through most of the install, I have tried multiple times same issue occurs.

Read other 4 answers
RELEVANCY SCORE 109.6

Hi, how are you?  I am posting here because my error is 0xC1900101 0x30018 (see pic).  I get "stuck" on 40% overall and 23% of installing features and drivers.  I say "stuck" because the inner percentage circle breathes but nothing happens past those percentages.
 
I have an Asus laptop running Windows 7 Home 64-bit on a Samsung SSD.  I read other forums to turn off antivirus - so I permanently turned all of Norton off but no luck 

A:Windows 7 to 10 error 0xC1900101 0x30018

Here I have the exact same problem. Also an Asus Windows 7 -64bits
It stucks at same 40% 23%

Read other 39 answers
RELEVANCY SCORE 108.4

Upgrading a Windows 8.1 installation and it stuck at getting devices ready at 2%. No BSOD. Has to be specific to 8.1 as I have already installed 10 on a clean partition with no issues on this machine. All drivers up to date. Did try removing Avast. No wireless devices attached. Not really bothered but an upgrade would save a few hours. Tried it twice and it sticks in the same place "Getting devices ready 2%" A reboot restores previous OS.
There is a lot written about this error applying to Windows 8 and wireless devices in laptops....this is a huge desktop machine.

A:Windows 10 Error code 0xc1900101-0x30018

I suppose when it ran the compatibility checker, it showed no problems?

There was a time when Bluetooth devices caused problems. If you have any, you might try disabling them in the Bios.

I have not done an install over 8.1. The one time I tried, it said it could not with Media Center installed, so I stopped.

No log files left after the failed attempt?

Read other 38 answers
RELEVANCY SCORE 106

In Dell Precision M6600 upgrading from Windows 10 to windows 10 Anniversity Edition fails with error

     0xc1900101 - 0x30018       The installation failed in the FIRST_BOOT phase with an error during SYSPREP operation.I tried the following:
1. Uninstalled all unused software and installed latest Dell BIOS version A15 and drivers from Dell Web site.2. In Device manager removed hidden devices.4. Installed upgrade from USB3 drive by selecting keep files and application. 5. Verified that     sfc /scannowdoes not find anything:    sfc /scannow    Beginning system scan.  This process will take some time.    Beginning verification phase of system scan.    Verification 100% complete.    Windows Resource Protection did not find any integrity violati    ons.6. Tried DISM    DISM /Online /Cleanup-Image /ScanHealth    Deployment Image Servicing and Management tool    Version: 10.0.10586.0    Image Version: 10.0.10586.0    [==========================100.0%==========================]    No component store corruption detected.    The operation completed successfully.6. Tried from command prompt    bootrec /fixmbr    bootrec /fixbootwhich worked without errors.7. Tried    bcdboot d:\windows /vwhich re-creates recovery partition successfully8. Used Windows 10 Upgrade troubl... Read more

Read other answers
RELEVANCY SCORE 98.4

Hey,

I've tried to install the Win 8.1 Update via the Windows Store and got the 0xc1900101 - 0x30018 several times after the PC restarted at the ending of the update.

I know that several users solved this with disabling drivers, so I did some suggestions I've found.

1. Disabling AV (Kaspersky)

2. Disabling LAN Controllers

3. Uninstalling DAEMON Tools, TuneUp

4.

--> DISM.exe /Online /Cleanup-image /Restorehealth

--> sfc /scannow  

--> wsreset.exe

5. Trying to repair Windows Update itself via "WindowsUpdateDiagnostic.diagcab"

6. Disabling AIDA

7. Disabling all components from my ASUS motherboard

some other things I can't remember...

For your information, I don't want to install Windows 8.1 from scratch, as I have too many programs and I never had problems with installing an OS for this system (Win7, Win8).

Thanks for the help

UpdateLog:
2013-10-17 21:31:41:150 5840 25f4 Handler Deleting setup file '9600.16415.winblue_refresh.130928-2229_x64fre_client_Professionalwmc_gdr_de-de-IR1_CPWMCA_X64FRER_DE-DE_ESD.esd'
2013-10-17 21:31:41:150 5840 25f4 Handler : Installer completed. Process return code = 0x00000000, result = 0x00000000, callback pending = true
2013-10-17 21:31:41:157 5840 25f4 Handler :::::::::
2013-10-17 21:31:41:157 5840 25f4 Handler :: END :: Handler: Windows Setup Install
2013-10-17 21:31:41:157 5840 25f4 Handler :::::::::::::
2013-10-17 21:31:41:162 1064 3218 AU Preventing expiration of po... Read more

A:0xc1900101 - 0x30018 Error during update -> restore Win8

I fixed it with these things:

1. Uninstalling DAEMON Tools, TuneUp
2. via CMD (as admin) -> DISM.exe /Online /Cleanup-image /Restorehealth
3. Disabling Intel LAN, Azalia Audio, USB 3.0 via BIOS

Read other 19 answers
RELEVANCY SCORE 97.6

Hello out there,

since seven days i try to update my system to WIN8.1. from the first try i get the errorcod 0xc1900101 - 0x30018.
I have already made a reinstallation of WIN8 and deinstalled everything exept the networkdriver. Allways get the same message. The installation seems to work fine till deviceconfiguration 64%. Then it restarts and sets back to WIN8.
My system is Satellite Pro C870 -1EJ
Need some help, or better an solution.

THX

verzweiflix

A:Satellite Pro C870 - Win8.1 update - Error 0xC1900101 - 0x30018

Just solved it myself,

and for anyone else with the same Problem.
It has been the Catalyst suite. Just deinstalled it and voila
It now works.

Read other 14 answers
RELEVANCY SCORE 87.6

So here is whats going on. Windows 8.1 failed to install. It would download, install, restart, install some more, restart, and then when it got to the updating devices or whatever it was exactly, it would error with 0xC1900101 - 0x30018. I found threads that pointed the issue to being wireless card issues. I tried updating the drivers before install, no go. The only thing that worked was disabling the card in the BIOS (I actually just ripped the damn thing out, but it works the same). So finally got windows 8.1 installed. Went to put my wireless card back in, booted up, almost instant frowny face blue screen. So 8.1 broke my wireless capability all together. If anyone has any ideas or knows how to fix this I would appreciate it. Otherwise it looks like I will just have to wait for microsoft to fix their default drivers or whatever they did. FYI, i have a ASUS Dual-band PCE-N35 wireless card.

A:8.1 Failure to install. 0xC1900101 - 0x30018

What about contacting ASUS and see what they say. I don't see any specific Windows 8.1 driver but maybe they have a beta version you could try.

Read other 11 answers
RELEVANCY SCORE 84.8

Hi All.

I am a Mac user, but bought a PC on craigslist, that had windows Windows 7 on it. I am trying to upgrade it to Windows 10 and it is failing every time. I have downloaded the update package and installed that way and it fails at 32% of total install, approx 12% of installing drivers and features. I have done quite a bit of reading on the subject so i have tried the following:

-removed all unnecessary hardware
-rolled back drivers
-update to newest drivers
-removed antivirus
-removed all aftermarket software
-attempted upgrade by installing via flash drive and by disc

there are probably others that i cannot recall in my frustration.

i have read about a video card causing issues. The mobo does not have onboard video and this machine has a GeForce 8600 GTS SLI, without the 2nd card installed.

not sure if it is worth buying a cheap card to install to see if that is the issue...
y
i am sure i will recall other specifics once we start some conversation here, but i would greatly appreciate your help. My intent is to donate this machine so i want to ensure it is working properly so i do not have to offer free tech advice in the future that i am not qualified to give.

Thanks in advance and Happy Holidays

A:Upgrading to Win10 from Win7; fails every time with 0xc1900101-0x30018

System File Checker indicates that there are some corrupt system files, but this is way above my head so i wouldn't know how to correct them.

i will post the log here when i can.

Read other 3 answers
RELEVANCY SCORE 80.8

I can't seem to update to windows 8.1 it gives me this error after logging in again:

"Couldn't update to Windows 8.1

Sorry, we couldn't complete the update to Windows 8.1. We've restored your previous version of Windows to this PC.

0xC1900101 - 0x40017"

The funny thing is that a few weeks ago I already updated to windows 8.1 but because of a faulty driver and not being able to boot into safe mode I had to renew my windows and downgrade to windows 8.0. But now I can't seem to update to windows 8.1 anymore. I installed all the windows updates even the optional ones. So I did a factory reset and uninstalled everything that didn't seemed necessary for windows so the update would go smoother. I found a toshiba page with a tutorial to how to update to 8.1 and it told me to uninstall the following:

Genesys Logic
Intel PROSet
Intel Wireless Display
Realtek-audio driver
TOSHIBA PC Health Monitor
Realtek WLAN driver
Realtek Bluetooth Filter driver

and on another page it told me to uninstall anything related with toshiba so I did all that and these are programs I currently have:

http://oi58.tinypic.com/2ak028l.png

I also tried with a clean boot but still no change. My graphics driver atm is version 8.9 while the most recent released version is 13.12 but toshiba only release update 12.1 for windows 8.1 and I did try installing that but it just got me into a endless boot loop.


My laptop:

Toshiba Satellite C855-255
PSCBYE-05000NDU

Coul... Read more

A:Upgrade to Windows 8.1 keeps failing - error 0xC1900101

I have a C850D-13F..
same error....help us...

Read other 2 answers
RELEVANCY SCORE 80.8

I have a samsung RV511, i5 processor, 4gb Ram it has windows 7 home premium.

I have been trying for days to upgrade to windows 10. It starts by copying the files and then on the first restart it gets stuck at the windows logo everytime. When i restart the laptop i get the message that the installation failed in the safe_os phase with an error during BOOT operation.

error 0xC1900101-0?20017.

I need your help to successfully upgrade to windows 10 home. I have attached the setuperr.log from C:\$Windows-BT\Sources\Panther\

A:Windows 10 Upgrade gives error 0xC1900101-020017

How about this: 0xC1900101 - 0x20017 Fixed!

Read other 0 answers
RELEVANCY SCORE 80

Can anyone help me with this error? I get it every time when trying to get version 1607. I have checked many times; this is not related to any drivers but to something I do not understand. Here are included my Panther and Rollback folders.
Sources.zip - Google Drive

Read other answers
RELEVANCY SCORE 74.8

Hi,

I am trying for days to upgrade my mam's laptop but I have no success...

Tried everything, was following the Toshiba instructions: "How to Upgrade"...

BUT i doesn't work.. i am always ending at the same error message...
0X1900101 0x30018

I almost deinstalled everything...just hold on to my ethernet driver... otherwise I might have no internetconnection.

What can I do?

A:Satellite C855-2J4 - can't upgrade to Win 8.1 - error 0X1900101 0x30018

In [Toshiba Support Win 8.1 Forum|http://forums.computers.toshiba-europe.com/forums/forum.jspa?forumID=139] you will find some threads about this Win 8.1 update issue.

Before opening new thread about the same theme, please check the provided solutions!

Read other 2 answers
RELEVANCY SCORE 74.8

on a laptop toshiba Satellite C875-152 update windows 8 to 8.1 does not.
I completely reset the pc and updated all the drivers as indicated, but the update is still not happening.

I have a 0xc1900101 error-0x30018

please, help me

A:Satellite C875-152 - Win 8 to Win 8.1 upgrade problem - error 0x30018

I wrote to Toshiba helpdesk but nobody helped me... I keep you informed?

Read other 2 answers
RELEVANCY SCORE 72.8

I have made several attempts to upgrade my desktop from 8.1 to 10. Each time the install freezes at the "copying files = 3%" point. When I reboot the system returns to my 8.1 setup and shows the above code with this explanation. "Installation failed in SAFE_OS phase with an error during APPLY_IMAGE operation"

Can anyone tell me what this means and how to resolve the issue?

A:Upgrade error 0xC1900101-0x2000C

Originally Posted by canuck257


I have made several attempts to upgrade my desktop from 8.1 to 10. Each time the install freezes at the "copying files = 3%" point. When I reboot the system returns to my 8.1 setup and shows the above code with this explanation. "Installation failed in SAFE_OS phase with an error during APPLY_IMAGE operation"

Can anyone tell me what this means and how to resolve the issue?



You are doing this from files that were downloaded to this PC and told you it was ready to install the upgrade ?

Read other 0 answers
RELEVANCY SCORE 64.4

The Problem
Main issue is that my Dell XPS 9343 Windows 8.1 is unable to boot (warranty expired a month ago). 
Main Symptom
Computer goes past the Dell screen, I can access system settings but then I receive an error saying a bootable drive cannot be found. 
What I have tried
First, I received error saying "Operating system has no signature. Incompatible with SecureBoot."I ran onboard diagnostics and everything came back normal. Next, I disabled secureboot. I received an error saying that it still cannot boot.
Then I changed the Boot sequence from UEFI to Legacy. I received an error: "No Boot Device Found. Press any key to reboot the machine."
I created a bootable usb drive for WIndows 8 using a different computer. It is able to boot but I can't access anything. If I try system restore, I receive an error saying "To use System Restore, you must specify which Windows installation to restore. Restart this computer, select an operating system, and then select System Restore." hen I try "Refresh your PC", it says "The drive where Windows is installed is locked. Unlock the device and try again." When I try "Startup Repair", it says it failed to resolve the issue.
I also cannot start the computer on Safe Mode. I tried these instructions www.dell.com/.../en
When I press Shift + F8, I do not get to Recovery mode; nothing happens.
Additional information
If relevant, my computer has whole disk encryption (fo... Read more

Read other answers
RELEVANCY SCORE 64

trying to update windows 8 to 8.1, when I've completed the download and I restart the computer I get an error message saying I need to restore, with error message:
0xc0000225

When I turn off the computer, and back on It says it wasn't able to update to 8.1, and it did changed back to regular windows 8.
and get this error message:
0xC1900101-0x20017

how can I fix this?
Not very good with computers

Read other answers
RELEVANCY SCORE 63.2

I have spent several hours trying to get my HP Envy upgraded from Windows 8.1 to Windows 10. I have updated all my drivers, removed all USB items, tried disabling my wifi, and tried installing via USB - all to no avail. Can someone please help me!

Read other answers
RELEVANCY SCORE 62.8

Hi Everyone,
I desperately need some help here. I recently sent in my laptop for a screen repair at the Dell depot. I got it back last week and the screen works fine, however, for some reason they reinstalled Windows 8.1 on my system. When I sent it in, my laptop had Windows 10 and was working perfectly normally.
Last week a Dell technician helped me to reinstall Windows 10. The process started, and as it was installing it performed a restart (as it said it would perform multiple restarts). Well during the restart the computer just hung up on the Dell logo. i let the computer sit like that as I didn't want to interrupt the installation, however eventually my laptop just turned off.
I then had to order a USB stick from Dell in order to reinstall Windows 8.1. This time, another Dell technician helped me out but made sure all my drivers were up to date. Same thing happened during this upgrade. The installation got hung up on the Dell logo. There were no signs of any computer activity (no spinning circle under the logo).
I can't believe this issue has been going on so long now. I feel like since I sent the laptop in with Windows 10, Dell could have the decency to send it back installed. Their techs seem to want to help but are getting me nowhere.
If someone could please help I would be so grateful. Thanks!

Read other answers
RELEVANCY SCORE 62.4

I have a Dell XPS 18 portable all-in-one machine that came with Windows 8, then I updated it to Windows 8.1 without any problems. It caught a nasty virus and I had to restore it to factory settings, which leaves me back at Windows 8.

I have tried multiple times to install the Windows 8.1 update through the Microsoft Store but keep getting Error Code 0xC1900101-0x40017. I have tried the following but get the same result;

Ran all of Windows Updates that would come upVerified that all drivers were up to date. Note: my video driver is NOT a Nvidia but an Intel. I've seen posts stating that this driver needs to be updated in order to fix the problem.Ran Selective Start Up

I don't know what else to do at this point because I have not been able to find anything online related to my problem. Please advise if you have any suggestions. Thanks!

FYI: Antivirus running is Avast!

A:Windows 8.1 Update Error 0xC1900101-0x40017 on Dell XPS 18

Hi, many people with your problem blame Avast for preventing Windows 8.1 installation - "Couldn't update to Windows 8.1 - 0xC1900101 - 0x40017" - Microsoft Community. You can try to uninstall Avast and run the Windows 8.1 upgrade.

Good luck, werty

Read other 7 answers
RELEVANCY SCORE 62.4

I recently upgraded from Windows 8.1 to 10 with my XPS 13 (9343) laptop. Before the upgrade, I had no problem with any of the following devices with Windows 8.1. After the upgrade, I started experiencing the following issues:
1) Wifi: After restart or waking from sleep, I had to reconnect to my home network.Automatic reconnection was enabled and network adaptor's power management was modified but reconnection did not work well.
2) I had serious problems with my Bluetooth, especially with BT headphones. Once paired, it seemed to be working. However, after disconnecting and reconnecting, the headphones got connected but I did not hear any sound. Later, the headphones did not get connected but kept going to pairing mode but the Bluetooth setting showed that they are already paired. I am using a Bluetooth mouse. Interestingly, if I turn off the Bluetooth (from setting) and turn it on again, my Bluetooth mouse never get connected again. 
Temporary solution: I installed network driver (9343_Network_Driver_74HW9_WN32_6.30.223.262.A01.exe) for Windows 8.1. This solved my wifi problem. I had reconnection all the time. 
Regarding the Bluetooth mouse, it works as well.
Regarding the Bluetooth headphones, they worked for a while but I suddenly lost sound. Settings window showed that my headphone is still connected and audio playback device still showed that my Bluetooth headphone is active. I simply lost sound. The only way to temporarily fix this problem was... Read more

A:XPS13 (9343) WiFi and Bluetooth problems after Windows 10 upgrade

http://www.dell.com/support/article/us/en/19/SLN148687/EN

Read other 7 answers
RELEVANCY SCORE 62

I receive a similar error again on our HP Pavilion Notebooks with AMD CPU when updating to Windows 10 Creator update as last time when updating to Windows 10. Our office has a few of the 17-G133cl notebook computers and all of them display the same error message: We couldn't install Windows 10 - 0xC1900101 - 0x20017 - The installation failed in the SAFE_OS phase with an error during BOOT operation. Which is similar to the error displayed during the initial Windows 10 update except that the error shown was 0x1900101 - 0x20000. Back then a BIOS update that became available that fixed the issue. We check for a new BIOS, but all notebooks have the latest BIOS already installed v. F.41 from 9/19/2016. All other systems including other none HP AMD computers upgraded just fine. Any ideas what could cause this issue with that type of system?

Read other answers
RELEVANCY SCORE 58.4

My Parents figured it was time to upgrade to ten so I made up a disc and upgraded both their computers to 10 build 10586 successfully. I had already had 10, I got new parts so I upgraded via a disk my dad made when 10 first came around, build 10240.

I want to play Forza 6 but unfortunately it isn't supported on my build of Win 10 and security is better on 10586 yada yada yada. I insert the same disk, upgrade begins, it goes through the whole process on the purple screen and when it goes for the first reboot, it boots back up into startup repair asking me to choose keyboard language. I choose a shut down and when the computer boots back up it tells me,

"Installation Failed in Safe_OS Phase With an Error During BOOT Operation 0xC1900101 ? 0x20017"

I have tried many of the suggested fixes, I have:
1. Tried installing with all USB ports vacant
2. Removed my wireless adapter
3. Installed using a clean boot
4. Removed IIS and its associated user
5. Completely uninstalled my antivirus
There may be more but I dont remember

Fresh Install is not an option so please dont suggest it, theres got to be a way around this issue.

I have attached the error log of my latest attempt at upgrading.

I've also heard that downloading the ISO and then modifying some intel file could be a possible fix but Id rather try something that doesn't include modifying the OS, that might bring up a "not genuine" error later as I have heard.happens.

Thanks in advance for your help ten... Read more

A:Cannot Upgrade Win X build 10240 to 10586 (0xC1900101 0x20017)

Download iso using this link, double click on it and run setup.exe.

Windows 10

Read other 4 answers
RELEVANCY SCORE 58

Hello,
since this morning I am trying to update Win 8 on Win 8.1. This works until notebook reboot. Then Win 8 Restored and the PC restarted again with the error message that the update was failed and the original Windows has been restarted with the error message 0xC100101-0x30018.

Thank you in advance for your help.
Win 8.1 was already installed, but due to a crash Win 8 has been renewed. All necessary updates are already made.

Greetings

A:Win 8.1 update - error message 0xC100101-0x30018

Try running this to see if there were any problems with W8 updates prior to upgrade (I don't know if it runs on W8).
There is this
System Update Readiness Tool

Also run the System Update Readiness Tool

For 32 bit Windows
http://www.microsoft.com/en-us/download/details.aspx?id=504

For 64 bit Windows
http://www.microsoft.com/en-us/download/details.aspx?id=1540

To see results click Start - All Programs - Accessories - Right click Command Prompt and choose Run As Administrator. Type (or copy the below line and one blank line underneath and right click in the command prompt window and choose Paste).

notepad %SYSTEMROOT%\Logs\CBS\CheckSUR.log

Read other 17 answers
RELEVANCY SCORE 56.8

Hi all, 

I have tried a number of times now to upgrade from Windows 7 to Windows 10. It always fails and puts out an error WindowsUpdate_C0000005. 

I did a search on this error which recommended using the Windows Updater Repair which I have done. However at the end of this it states it is unable to fix Windows Updater Error 0x80070057. 
Another search done led me to https://social.technet.microsoft.com/Forums/windows/en-US/53a1f2ab-037b-438e-a690-00a0e745730d/windows-7-update-error-0x80070057?forum=w7itprogeneral which suggests using RegEdit to fix the problem however the keys that
are referenced in this don't exist for me. 
Any thoughts here?

A:Unable to upgrade to Windows 10 - Windows updater error 0x80070057

Hey, this may help you. Change the following for 0x80070057 error on your system:
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SOFTWARE\MICROSOFT\WindowsUpdate\UX]
?IsConvergedUpdateStackEnabled?=dword: 00000000
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsUpdate\UX\Settings]
"UxOption"=dword:00000000

Read other 5 answers
RELEVANCY SCORE 56.4

I plan to swap out my pre installed 512GB  SSD with a 1TB SSD
 The instaled drive is a LITEON LGH-512V2G-11 M.2 2280 512GB 
Could someone advise if the 9343 supports MVME SSD and recommend a 1TB replacement.
Any advise woud be greatly appreciated.
Thanks

A:XPS 9343 SSD upgrade

The system supports M.2 SATA only - NO NVMe -- but there are indeed 1T 2280 M.2 drives you can use.

Read other 1 answers
RELEVANCY SCORE 54.8

from 8 pro 64bit (with media centre) to 8.1, tried many times, no luck, always end up getting the same error code 0x20017, then rolled back to 8, every driver has been updated and there no external driver whatsoever, any help, please.

A:0xC1900101 - 0x20017 error while updating?

Hello wgan,

Is your Windows drive encrypted by chance?

If so, you'll need to decrypt it first, then update to 8.1. Afterwards, you could encrypt it again if you like.

Hope this helps,
Shawn

Read other 6 answers
RELEVANCY SCORE 54.8

HI.
I've got a Dell Inspiron 660S that I'm trying to update to W8.1 from W8.0 and I keep getting this error every time I try.

Here is what I have done so far:

uninstalled speccy, avast
updated all legacy programs
updated all store apps except Microsoft Solitaire and Photos (they refuse to update)
ran Windows Update - took everything except .Net Frmwk 4 and Skype
ran disk cleanup, making sure to delete all temporary files
checked the prefetch folder and it's at 0 bytes

Having problems with DISM:
Dism /Online /Cleanup-Image /RestoreHealth doesn't complete
Dism /Online /Cleanup-Image /CheckHealth doesn't complete
Dism /Online /Cleanup-Image /ScanHealth says component store is repairable
Dism /Online /Cleanup-Image /AnalyzeComponentStore won't run - says it's not a good command or something like that

sfc /.scannow has 2 problems which will not resolve:
2015-11-12 21:38:05, Info CSI 000006e1 [SR] Repairing corrupted file [ml:48{24},l:46{23}]"\??\C:\Windows\SysWOW64"\[l:78{39}]"api-ms-win-eventing-provider-l1-1-0.dll" from store

2015-11-12 21:38:05, Info CSI 000006e4 [SR] Repairing corrupted file [ml:520{260},l:46{23}]"\??\C:\Windows\System32"\[l:78{39}]"api-ms-win-eventing-provider-l1-1-0.dll" from store

I grabbed the ESD file from the C:\$Windows~BT\Sources folder, and successfully created the W8.1 ISO, using the ESD to ISO tool from W10 forums, so I know it's not a bad download.

I'm just about... Read more

A:error 0xc1900101-0x20030018 updating w8.0 to w8.1

Hi, simrick. On break and have but a few minutes.
I know you're good friends with Wyn. I remember and ask her why she was not able to upgrade a machine from 8 to 8.1. I think it had to do with the processor? Check the SecurAble program in the "Installation" section about PAE, NX, and SSE type processors here: Suggested Steps To Take Installing And Setting Up Windows 8
Have you tried upgrading via the Store? Is there a link there? If not there is an update that does so. Shawn should have it in a tute here in 8F.

Those broken files concerning the Store concern me. Is there a install log file of the failed install on your machine? If so, look in there.
Never heard or seen anyone installing with an ESD to ISO with 8 to 8.1, (migfht not be possible with OEM key?) just a fresh install with ISO downloaded from MS site. Check.this out: Windows 8 and Windows 8.1 ISO - Download or Create
Are all drivers up to date? You might want to disable startup items and unplug any unnecessary devices before installing.
Have you tried Upgrade Assistant? Upgrade Assistant: FAQ - Windows Help
That's all I can think of for now. I'll try to check up on you later. I have pool league tonight though. If not, tomorrow morning.

Read other 5 answers
RELEVANCY SCORE 54.8

8.1 install error 0xC1900101-0x40019 and 0x80070652 and Windows 8.1 installation failed and reverted back to Windows 8.0

I'm lucky the computer even came back to life. I have an Intel HD Graphics 4000 video card, so the review from ADRStudio replied on February 15, 2014 on page 18

could address this problem but I'm not so sure. I can't find the Win 8.1 drivers at HP for my machine, they only offer Windows 7 or 8.

I've been reading Latest Win 8.1 ISO "Breaks" System Image Functionality

and on my dual boot laptop with Win 7, this may be a fatal error when trying to install Win 8.1 because 8.1 adds another System partition and kills off the one I had been using.

Considering the overwhelming severity of this problem and how widespread & long-going it is, I'm gonna stick to Win 8.0 for now.

A:8.1 install error 0xC1900101-0x40019

Download the attached file.. Right click and Run as Administrator.

This will create a compressed folder on the Desktop, attach it to your next post.

Read other 1 answers
RELEVANCY SCORE 54.4

I tried installing the Anniversary update using the Media Creation tool and I get this error when I log back in after the setup reverted my installation:

0xC1900101-0x3000D
The installation failed in the FIRST_BOOT phase with an error during MIGRATE_DATA operation

Any help would be greatly appreciated!

Read other answers
RELEVANCY SCORE 54.4

I have Asus X54hr with windows 8 pro.

I have already updated all my drivers, at least I think so.

And I dont have third party antivirus program, only defender, which I shut off before update.
Run update with clean boot and gone though several suggestions how to install w8.1

like this one:
Windows 8.1 Update Error 0xC1900101-0x40017 on Dell XPS 18
But I still got error message 0xc1900101 - 04000d after restarting my computer when installation freezes( screen goes black after restart when setup applied pc settings.

Any suggestions? Or I need to provide more info?

A:Error 0xc1900101 - 04000d after w8.1 install from store

Ok, I get 8.1 into system.

I downloaded iso file with Os installation, and run setup only with saving personal files.

Read other 1 answers
RELEVANCY SCORE 54

Windows Vista x86 and Windows 7 x86 users in Catch 22 situation trying to restore systems!
During Factory Restore of Vista x86, upgrade of Vista x86 to Windows 7 Ultimate x86 SP1, or install of Windows 7 Ultimate x86 SP1 and validating install online, Windows Update fails after mandated update.
Unable to manually download requisite updates due to "Browser our of date" error from Microsoft Support website!
Downloads only available from Support.Microsoft.com website

Read other answers
RELEVANCY SCORE 53.6

Windows 10 1511 will not update to 1607 by any method. Updates always complete to 100% then revert. Computer is a Dell Vostro 1720.

Background: The computer never appeared to update automatically, but there was never any error code. I tried to use the Windows 10 upgrade assistant. The upgrade would go through download and install to 100% but then restart back to version 1511 with no error message. Finally, I downloaded the 1607 iso, extracted it to my hard disk, and installed from there. Again the update went to 100% and then reverted back to 1511, but this time it gave the error message 0xC1900101 - 0x20017 "The installation failed in the SAFE_OS phase with an error during BOOT operation."

I have found several threads about this error, and it seems most likely that there is a driver conflict of some kind. I have looked at the setuperr.log from $WINDOWS.~BT/Sources/Panther/ directory but I do not see what is causing the error. Can anyone help with guidance on this?

setuperr.log text:

2016-09-21 19:53:52, Error CONX Windows::Compat::Appraiser::Utilities::SendRequest (1259): Failed to connect to the internet or send request: [12007].[gle=0x80072ee7]
2016-09-21 19:53:52, Error CONX Windows::Compat::Appraiser::Utilities::ResolveForwardLink (1319): Failed to send request using default proxy[gle=0x80072ee7]
2016-09-21 19:54:32, Error CONX Windows::Compat::Appraiser::Utilities::SendRequest (1259): Failed to connect to the internet or send request: [12007].... Read more

Read other answers
RELEVANCY SCORE 51.6

Hello,   I have been trying to upgrade my IdeaPad 110 to the New Windows Insider Preview Version 17063. I can't get past the 2 reboot Error Code 0xc1900101I have been told to Disable Virtualization, which is already disabled and AppGuard, which I don't see in my BIOS. The only thing I have in my BIOS is Intel Platform Trust Technology & Secure Boot, which I have disabled. I have been trying to upgrad 10 x and the same problem happens. Anybody else having the same problem? Is there an AppGuard in BIOS?

Read other answers
RELEVANCY SCORE 50.4

Everytime I try to update my computer to windows 10, I get the same error occurring. Ive tried multiple methods but I can not get around it. Downloading it works, but once the installing gets to the first re-boot, the machine hangs with the dots that are meant to be going in a circle just freezing. Nothing happens no matter how long I leave it for, so I have to hard-reset. Once I done that it tries to recover the installation but the same thing happens again so then it just sets me back to windows 7.
 My computers model is Alienware_Aurora_R3
Attached is the error message I get when I am rolled back to Windows 7. 
Ive tried looking online for solutions but cant find any that work for me so far. Any help? 


A:Windows 10 Failed to Install 0xC1900101 0x30017

I have the same PC and the exact same error occurs on my system.  i spend two hours with Microsoft Tech support on the phone to no avail.  I have no idea what to do about except stay with windows 7 which works just fine.

Read other 3 answers
RELEVANCY SCORE 50.4

Hello,

I have a problem with installing Windows 10 (either upgrade or clean install). I think the problem has started 2.5 years ago when suddenly Windows 8 stopped installing updates. I think it stopped installing updates after the Windows 8.1 upgrade through the store has failed.

Just about a month ago, updates resumed and a bunch of them were installed. But after several days, one security update has failed to install and Windows update is stuck at this point.

I decided last week to upgrade to Windows 10. Direct upgrade wasn't possible because I have o upgrade to Windows 8.1 first, which I can't. So I have created a clean install media on USB using the media creation tool. I plugged in the USB, shut down then started and selected the USB drive as first choice for booting. It brought the Windows logo, and 1 minute later, the laptop shut down. I repeated the operation twice with the same result.

I tried then to do a clean install of Windows 8.1 from another USB, but shortly after the logo, instead of shutting down, I got a light blue screen with "something went wrong" message and the machine restarted.

Then I decided to run the USB that have Windows 10 from Windows. I selected to remove every thing and proceeded. The process after that went slow increment of 1% took about 10 minutes. Then I got the first restart, and it went the same as it shut down. I started the laptop and it went again to Windows 8. After I logged on, I got the following message:

We couldn'... Read more

Read other answers
RELEVANCY SCORE 50.4

Dell detect finds a new display driver. I download and install it - BUT it doesn't install. I get an Intel error telling me it is not a mfg driver. How do I update this?
XPS13-9343, Windows 10,  w/ultra HD display and 5500 Intel graphics

A:XPS 13-9343, Dell Detect error

If your currently installed version is the latest Dell 20.19.15.4531, A04 driver. Then the Dell detect software is in error.

Read other 1 answers
RELEVANCY SCORE 50

Hi, this is my first post so I apologize in advance for any naivete.

Right, so I've been using Windows 10 home without (much) issue for months now, and I decided to do the anniversary upgrade. All is well until it gets to ~75% at which point I blue screen with error






0xC1900101-0x4000D - The installation failed in the SECOND_BOOT phase with an error during MIGRATE_DATA operation



This started me off on a long and frustrating journey over the last three days desperately trying everything I could find online to fix the issue, but I'm at the point of giving up, so I figured maybe some kind soul would aid me online.

Thing's I've tried thus far (that I can remember - it's been a lot):
Doing the anniversary upgrade from windows updateDoing the anniversary upgrade via the windows upgrade assistantDoing the anniversary upgrade via ISODoing the anniversary upgrade via ISO from bootable USBReinstalling (not fresh) Windows 10, which yields bsod




0xC1900101-0x2000C - The installation failed in the SAFE_OS phase with an error during APPLY_IMAGE operation



Ran chkdsk, which fixed a couple corrupt files, but didn't solve the problemRan sfc, which reported no errorsUpdating every driver I could (using DriverMax to identify out of date drivers, but not to install them)Ran driver verifier with all options but low resources simulation on all non-microsoft drivers, which causes a bsod before it gets to login



... Read more

A:Windows 10 Anniversary Update BSOD 0xC1900101-0x4000D and More!

Ran the DM Log Collector - attached is the result.

Read other answers
RELEVANCY SCORE 49.6

Hi,
Today I downloaded the "new" intel display driver (9343_Video_Driver_RTWTF_WN32_20.19.15.4531_A04) but once it is trying to install the driver it gives me an error that this driver is not made for this laptop and I have to go to the manufacturer for the driver ... well I do think I got it from the Dell support page ......
Anyone else encountered this issue and maybe have the solution?
- Tried uninstalling previous driver - no success
- Always used the dell driver

Read other answers
RELEVANCY SCORE 49.2

Previously, I'd gone through a terrible tribulation trying to get my two HP computers from the initial RTM build 10240 to version 1607 Anniversary Update. Spent hours/days trying to troubleshoot it. The only thing that eventually worked was to download a specific ISO file, for version 1511 build 10586.679. I did try updating to 1607 in the next step, but that failed... and I gave up.

Fast forward a couple months, 1607 got pushed to one of my computers successfully. However, the other one ended up failing.

There were many posts about this issue back in the earlier days of people trying to update from RTM 10240. Deja-vu. However, nothing seems to work. I tried downloading the 1607 ISO file and running it... which resulted in the error above after about 1.5 hours. Next, I used the Media Creation Tool to try getting 1607 installed... ran into the same error again.

I did leave the notify Microsoft option in place, so whatever errors were made ended up forwarded to Microsoft. But I'm wondering if there's anything I can do to fix this... or if I'll just have to wait. Any thoughts/suggestions?

Thanks!

Read other answers
RELEVANCY SCORE 49.2

HI. Config:

OS Name Microsoft Windows 10 ProVersion 10.0.14393 Build 14393Other OS Description  Not AvailableOS Manufacturer Microsoft CorporationSystem Name DESKTOP-CN3H81KSystem Manufacturer Dell Inc.System Model XPS 13 9343System Type x64-based PCSystem SKU 0665Processor Intel(R) Core(TM) i5-5200U CPU @ 2.20GHz, 2195 Mhz, 2 Core(s), 4 Logical Processor(s)BIOS Version/Date Dell Inc. A11, 12/8/2016SMBIOS Version 2.8Embedded Controller Version 255.255BIOS Mode LegacyBaseBoard Manufacturer Dell Inc.BaseBoard Model Not AvailableBaseBoard Name Base BoardPlatform Role MobileSecure Boot State UnsupportedPCR7 Configuration Binding Not PossibleWindows Directory C:\WINDOWSSystem Directory C:\WINDOWS\system32Boot Device \Device\HarddiskVolume1Locale United StatesHardware Abstraction Layer Version = "10.0.14393.206"User Name DESKTOP-CN3H81K\lucasTime Zone Tokyo Standard TimeInstalled Physical Memory (RAM) 8.00 GBTotal Physical Memory 7.60 GBAvailable Physical Memory 5.22 GBTotal Virtual Memory 9.48 GBAvailable Virtual Memory 7.13 GBPage File Space 1.88 GBPage File C:\pagefile.sysHyper-V - VM Monitor Mode Extensions YesHyper-V - Second Level Address Translation Extensions YesHyper-V - Virtualization Enabled in Firmware YesHyper-V - Data Execution Protection Yes
Always same pattern, infrequ... Read more

Read other answers
RELEVANCY SCORE 48.8

This x64 system was upgraded from Windows 7 Ultimate in August 2015. All the patches and updates have been applied successfully. I have eliminated all but one error. I have been working on this for days. I would appreciate any help resolving this error:

2016-08-24 15:35:51, Error MOUPG CInstallUI::GetDefaultLanguage(1715): Result = 0x80070002[gle=0x00000002]
2016-08-24 15:43:43, Error MOUPG CSetupManager::GetDUSetupResults(5249): Result = 0x80070490

Read other answers
RELEVANCY SCORE 48.8

Hi,

Have a legit copy of Win 7 that was installed on PC that I built. Then upgraded to Ultimate via Windows Anytime Upgrade. I have a box with the product key but no disk.
My hard drive crashed and PC went in for repairs. The guy installed a new version of Ultimate as a clean install.
After some months, I got message that Windows is not genuine.
I tried the activation option with my upgrade key but received a message that this product key can only be used for upgrades, not clean installations.
What are my options?




Code:
Diagnostic Report (1.9.0027.0):
-----------------------------------------
Windows Validation Data-->

Validation Code: 0
Cached Online Validation Code: N/A, hr = 0xc004f012
Windows Product Key: *****-*****-GJY49-VJBQ7-HYRR2
Windows Product Key Hash: W5/6nm6F2UPXrCkY5xUhXb/+21g=
Windows Product ID: 00426-OEM-8992662-00006
Windows Product ID Type: 2
Windows License Type: OEM SLP
Windows OS version: 6.1.7601.2.00010100.1.0.001
ID: {FB464892-DDB9-40CB-8AC6-FC7124DDF2B9}(3)
Is Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/A, hr = 0x80070002
Signed By: N/A, hr = 0x80070002
Product Name: Windows 7 Ultimate
Architecture: 0x00000009
Build lab: 7601.win7sp1_gdr.151230-0600
TTS Error:
Validation Diagnostic:
Resolution Status: N/A

Vista WgaER Data-->
ThreatID(s): N/A, hr = 0x80070002
Version: N/A, hr = 0x80070002

Windows XP Notifications Data-->
Cached Result: N/A, hr = 0x80070002
File Exists: No
Ve... Read more

Read other answers
RELEVANCY SCORE 47.6

I have been trying to update my computer to service pack 2 but it keeps failing. I get the error code in the subject, file not found.  I even tried a clean boot and shut off my anti virus and firewall. I tried cleaning up the windows update history as well. I tried the system update readiness tool as well but that just hung.  I had the computer previously cleaned in this forum, http://www.bleepingcomputer.com/forums/t/476212/possible-spyware/.  I am not sure if some files were corrupted after the cleaning. I am running the 64 bit version on a HP Pavilion laptop.  I hope someone can help because I would like to have the latest version.  Thanks.

A:Unable to Upgrade to Service Pack 2: Error Code 0x80070002

Well...that "cleaning" took place in Dec 2012...so I would not count on that as any indication about the current status of malware possibilities.
 
Have you tried MS Fixit ?
 
Louis

Read other 1 answers