Over 1 million tech questions and answers.

BSOD Drive Power State Failure, ntoskrnl.exe, USB ports not working

Q: BSOD Drive Power State Failure, ntoskrnl.exe, USB ports not working

Hi,

I have a 2 week old HP Envy 14, running Windows 7 Home Premium 64bit, 4GB Ram, and an ATI Radeon HD 5650 Graphics card.

Initially for the first few days the notebook worked well, no problems. This week, I encountered the dreaded BSOD. The notebook had trouble shutting down or restarting, taking 10-15 minutes or so. Upon rebooting, I get a BSOD with DRIVER_POWER_STATE_FAILURE message.

I also encountered the USB not recognizing anything that was connected to it after the computer started. If the mouse/ thumbdrive was connected before the computer booted up, it worked. If it was disconnected after booting up, and reconnected the mouse/ thumbdrive would not work. I do not get anything (no error messages or acknowledgement that anything was connected).

I checked the Device Manager, and there are no error messages.

Strange this is, these problems happen sporadically. Sometimes everything works well- USB working as it should, not issues restarting etc. Upon rebooting, the problem starts again.

I've tried updating the latest Win updates, drivers, HP bios etc but still no luck.

Please help. Thank you in advance.

RELEVANCY SCORE 200
Preferred Solution: BSOD Drive Power State Failure, ntoskrnl.exe, USB ports not working

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: BSOD Drive Power State Failure, ntoskrnl.exe, USB ports not working

Hi cabe and Welcome to SF!

First of all, hpdskflt.sys was mentioned in the crash dmp, it belongs to HP Mobile Data Protection System Disk Filter. I would download and install fresh copy of the driver, or might be uninstall it to see if it has anything to do with the crashes you've experienced.

For the mouse and thumbdrive, you might want to have their drivers installed properly, or perhaps you might want to try to have fresh re-install of USB driver by going to Device manager, under USB list you uninstall everything then restart your system. (To go to Device manager, right click on computer and choose manager)

In looking through your driver, I can see some out of date one:

Code:
btwl2cap btwl2cap.sys Fri Apr 03 19:28:45 2009 (49D6A9BD)
Broadcom Bluetooth L2CAP Service. Please download and install fresh update of it


Code:
RimSerial_AMD64 RimSerial_AMD64.sys Mon Nov 24 11:01:01 2008 (492ADDCD)
Virtual Serial Port driver for Blackberry. This need to be updated as soon as possible

BUGCHECK SUMMARY:

Code:
BugCheck 1000009F, {4, 258, fffffa800416d680, fffff80000b9c510}

Unable to load image \SystemRoot\system32\DRIVERS\hpdskflt.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for hpdskflt.sys
*** ERROR: Module load completed but symbols could not be loaded for hpdskflt.sys
Probably caused by : umbus.sys

Followup: MachineOwner
---------
Regard,

Tuan

Read other 7 answers
RELEVANCY SCORE 104.8

I'm getting (seemingly) random BSOD's, and according to bluescreenview it's caused by ntoskrnl.exe. Not really sure how to fix this, and what it means.

It's a relatively fresh install of windows, built PC

AMD phenom II X4
ECS a750GM-M V7.0 motherboard
G Skill memory (4 GB)
Windows 7 Pro x64
if any of that is relevant.
All windows updates are installed
All drivers are up to date

It says I'm not permitted to upload the .dmp files, so I'll post them on Mediafire, unless there's a way I can view them myself and post them.

Mediafire link to all four dump files: http://www.mediafire.com/?psykx435dqvuabq,8m3hdbhxsquktsg,mth615eme064b6k,m6n5nd3144355os

A:BSOD, driver power state failure, ntoskrnl.exe

Hi -This is a way to see the BSOD records and post them here -Download BlueScreenView:http://www.nirsoft.net/utils/blue_screen_view.htmlunzip downloaded file and double click on BlueScreenView.exe to run the program.when scanning is done, go to EDIT - Select AllGo to FILE - SAVE Selected Items, and save the report as BSOD.txtOpen BSOD.txt in Notepad, copy all of the content, and paste it into your next replyThank You -

Read other 13 answers
RELEVANCY SCORE 104.8

Hey, my desktop computer keeps freezing here and there. I have a bad feeling it happens when working with my data HDD (not a system one). Some applications freeze and some not, I can restart, but it gets stuck when "Turning off" .. after few mins I get BSOD.

I've tried to boot up with driver Verifier and it freezes right after login screen .. no BSOD (within 30 mins).

The only thing I know from minidump is that it causes ntoskrnl.exe

Would someone help me to identify my problem?

Thanks in advance.

A:BSOD Driver Power State Failure ntoskrnl.exe

Welcome aboard.

Code:
fffff880`0355b488 fffff880`010bb041Unable to load image \SystemRoot\System32\Drivers\sptd.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for sptd.sys
*** ERROR: Module load completed but symbols could not be loaded for sptd.sys
sptd+0x3f041
sptd.sys is the most well known causes of a crash in windows 7. There are some technical reason behind it is that much crash prone. It is a paer of Daemon tools, so better you uninstall Daemon Tools.

Also free up the startup.
Click on the Start button
Type ?msconfig (without quotes), click the resulting link. It will open the System Configuration window.
Select the ?Startup? tab.
Deselect all items other than the antivirus.
Apply > OK
Accept the restart.
Let us know the results.

Read other 8 answers
RELEVANCY SCORE 104.8

Hello guys,
I tried resolving this issue by myself, but I can't figure it out. I'm getting BSOD on my new laptop. The laptop is brand new, I bought it about one month ago. It came with the default linux OS installed by the manufacturer, but I did a format and I installed Windows 7 Ultimate x64.
Machine specs:
Acer Aspire V3-771G 736b4G75Maii
CPU: Intel Core i7-3630QM 2.4GHz with Turbo Boost up to 3.4GHz
GPU: nVidia GeForce GT 640M 2GB DDR3 memory
RAM: 1x 4GB DDR3
HDD: 750 GB Toshiba

I got BSOD 3 times, every time I was browsing the internet using Mozilla Firefox. First couple of times I was on facebook checking some pictures and the 3rd time I was on forums looking for a solution to this problem. The BSOD happened when the laptop was on high performance settings, but i can't remember if it was plugged in or not.

As i said, the laptop is 1 month old, but it came with a broken speaker so it was sent to the service where they replaced the entire front cover. They said the reason is that the speakers are glued to the front cover so it was not possible to replace only the speakers. Before sending the laptop to the Acer service I did not experienced any BSOD and I used it for like 2-3 weeks, I even did some gaming on it.
The first BSOD occurred last week and the laptop wasn't used until yesterday when it happened again and the last BSOD happened just earlier today.

I will attach the prefmon.html and the folder with the files I got from the BSOD_Windows7_Vista_v2.64_jcgriff2_.ex... Read more

A:BSOD ntoskrnl.exe driver power state failure

I forgot to mention, from the last BSOD in event viewer i have the following events:
Event 6008
The previous system shutdown at 3:44:38 PM on ‎8/‎19/‎2013 was unexpected.

Event 1001
The computer has rebooted from a bugcheck. The bugcheck was: 0x0000009f (0x0000000000000003, 0xfffffa8005294a10, 0xfffff80000b9c3d8, 0xfffffa8004b9a570). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 081913-17596-01.

Event 41
The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.

Event 1101
Audit events have been dropped by the transport. 0

Event 10002
WLAN Extensibility Module has stopped.

Module Path: C:\Windows\system32\athihvs.dll
Event 4001
WLAN AutoConfig service has successfully stopped.
Event 37
The speed of processor 0 in group 0 is being limited by system firmware. The processor has been in this reduced performance state for 41 seconds since the last report.

this last event shows up 8 times, one for each core. The CPU has 4 physical cores, but with hyperthreading it has a total of 8.

I did a Driver Verifier according to the instructions posted here (http://www.techsupportforum.com/foru...ed-473665.html) and there was no BSOD.

Read other 16 answers
RELEVANCY SCORE 104.8

Hello, my computer has crash 4 times within the past two hours. I believe it has something to do with the Elgato Game Capture HD software I installed on the computer, since it seemed to only happen when I was either using it, or trying to uninstall it. Currently, I've uninstalled it, and no BSOD so far. I have updated my drivers and performed any windows updates available. Please help.

Thanks in advance.

Read other answers
RELEVANCY SCORE 104

Hello,

I've had 3 BSOD in the last few days, usually when my computer is asleep or when I am not actively using it. Malwarebytes anti-malware software indicates no issues, as does esot nod antivirus5.

Ran a free program (BlueScreenView v1.47 by nirsoft) which indicated a driver power state failure and/or a ntoskrnl.exe problem.

I do not know how to proceed, and would love some advice!

A:BSOD - driver power state failure or ntoskrnl.exe problem?

All of your crashes are caused by your Texas instruments USB 3.0 driver:


Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa80140bfcd0, fffff80000b9c3d8, fffffa8011a2aac0}

*** WARNING: Unable to verify timestamp for tihub3.sys
*** ERROR: Module load completed but symbols could not be loaded for tihub3.sys
Probably caused by : tihub3.sys

Followup: MachineOwner
---------
Driver Reference Table - tihub3.sys
Looking at the driver we can see it is rather old:

Code:
kd> lmvm tihub3
start end module name
fffff880`053d7000 fffff880`053fb000 tihub3 T (no symbols)
Loaded symbol image file: tihub3.sys
Image path: \SystemRoot\system32\DRIVERS\tihub3.sys
Image name: tihub3.sys
Timestamp: Wed Nov 23 00:50:16 2011 (4ECC8998)
CheckSum: 00021577
ImageSize: 00024000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
Please update your driver from here: Analog, Embedded Processing, Semiconductor Company, Texas Instruments - TI.com

Read other 5 answers
RELEVANCY SCORE 104

Hi!

I recently got a laptop from Scan.co.uk, it's a custom build using the Clevo kit.
I have been having intermittent BSOD's with a Driver Power State Failure message at random times, I can't see a discernible pattern.

It can happen whether on the desktop, chrome or gaming but generally on the desktop during minimal use.
I can play games for around 8 hours without issue but sometimes I'll get the error straight after booting up or whilst shutting down or just doing work in chrome.

I've seen people with similar issues in this forum and have tried to make sure all my drivers are up to date but I'm missing something somewhere

Any help offered would be greatly appreciated

Steps I've taken so far;

Avast Virus scan - No threatsEset online scan - No threatsAll windows Updates AppliedDism run
"Dism /Online /Cleanup-Image /ScanHealth" - The component store is repairable. The operation completed successfully."Dism /Online /Cleanup-Image /CheckHealth" - The component store is repairable. The operation completed successfully."Dism /Online /Cleanup-Image /RestoreHealth" - The restore operation completed successfully. The component store corruption was repaired. The operation completed successfully.

A:BSOD Driver Power State Failure ntoskrnl.exe+153ca0

Hi ApocalypseMeow & Welcome to the forums ^_^,

I have analysed your dump files and below has been provided an analysis of the same for informative purposes :-

Code:
0: kd> !irp ffffe0011851f010
Irp is active with 6 stacks 4 is current (= 0xffffe0011851f1b8)
No Mdl: No System Buffer: Thread 00000000: Irp stack trace.
cmd flg cl Device File Completion-Context
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
>[ 16, 2] 0 e1 ffffe001143e9880 00000000 fffff801f3aa2fc4-ffffd0002a3468f0 Success Error Cancel pending
\Driver\pci dxgkrnl!DpiFdoPowerCompletionRoutine
Args: 00000000 00000001 00000001 00000000
[ 16, 2] 0 e1 ffffe00117f61040 00000000 fffff800b4395fd8-ffffe0011a826f08 Success Error Cancel pending
Unable to load image \SystemRoot\system32\DRIVERS\nvlddmkm.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
\Driver\nvlddmkm nt!PopRequestCompletion
Args: 00000000 00000001 00000001 00000000
[ 0, 0] 0 0 00000000 00000000 00000000-ffffe0011a826f08
Args: 00000000 00000000 00000000 00000000


As we can see that the "nvlddmkm.sys" which is the... Read more

Read other 7 answers
RELEVANCY SCORE 104

I've been experiencing this BSOD on and off for a while now, and after doing some research came across a forum post suggesting to do a memtest. I've only had time to run it for 3 passes and will try for the full 8 later in the week when I have more time.

I thought I would start a thread to make sure there are no other underlying issues that could be the cause of the BSOD. Attached are the SF Files. Thanks!

A:BSOD Driver Power State Failure 0x0000009f (ntoskrnl.exe)

Hi MSB117.

The dedicated GPU is totally out!!! Does a restart brings it back?

Yes, a stop 0x9F can do it, based on sleep/hibernation settings and it is often seen for Optimus Technology/Switchable graphics. It is not the first instance.

As the GPU is causing continuous issue over a time, I would suggest you to contract Dell/Alienware servicing center.

Read other 7 answers
RELEVANCY SCORE 104

Hello,

This morning when i woke up when i switched my pc's monitor i got those beloved letters.My computer was on idle,probably it fell asleep.The settings on power options were on Balanced mode.Pc is on stock clocks.No overclock made.
Heres the minidump file.
Notice: this happened a couple of days once i updated lots of windows updates.

A:BSOD - Driver power state failure - ntoskrnl.exe+75bc0

Welcome to the Forum.

AVG is contributing to your BSOD. Please remove it for testing purpose. Use Microsoft Security Essentials.

Recommended from a strict BSOD perspective, compatibility & stability compared to other security software:

Microsoft Security Essentials - Free Antivirus for Windows

Malwarebytes - Free

Good and Free system security combination.

Reduce items at start-up: Startup Programs - Change

Perform a clean boot: Troubleshoot Application Conflicts by Performing a Clean Startup

Please update these older drivers. Links are included to assist in looking up the source of the drivers. If unable to find an update, please remove (un-install) the program responsible for that driver. DO NOT manually delete/rename the driver as it may make the system unbootable!:-

Rt64win7.sys Thu Feb 26 15:04:13 2009 (49A65B0D)
Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC
Driver Reference Table - Rt64win7.sys

Perform a clean install of a driver following: How to Clean Left Over Driver Files with Driver Sweeper

Use Revo Uninstaller to uninstall stubborn software. Opt for Advance Mode while uninstalling which allows leftover registry removal:Download Revo Uninstaller Freeware - Free and Full Download - Uninstall software, remove programs, solve uninstall problems

Scan with Kaspersky TDSSKiller:Anti-rootkit utility TDSSKiller

ESET online scanner: Free Online Virus Scanner | ESET

Run a System file check (SFC): SFC /SCANNOW Com... Read more

Read other 1 answers
RELEVANCY SCORE 104

Hello,

I've been having bsod's for a while ever since I disabled the Automatic Restart. I'm going to say that I figure it might have something to do with my Toshiba external hdd but I hope I can get a fix for this. I've spent days researching online - I've tried to find if I had any drivers to update by going to my Device Manager but all "update driver" results I get are the same: they are up to date.

My zipped minidump files: http://sdrv.ms/YPs4lS
Win7 Home Premium x64
Dell Inspiron 580S
Intel Pentium G6950 2.80GHz
4GB of RAM
Service Pack 1

Most recent crash info:On Sun 2/24/2013 1:44:16 AM GMT your computer crashed
crash dump file: C:\Windows\Minidump\022313-16130-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x75C40)
Bugcheck code: 0x9F (0x3, 0xFFFFFA80059EB060, 0xFFFFF80000B9C518, 0xFFFFFA80074604B0)
Error: DRIVER_POWER_STATE_FAILURE
file path: C:\Windows\system32\ntoskrnl.exe
product: Microsoft? Windows? Operating System
company: Microsoft Corporation
description: NT Kernel & System
Bug check description: This bug check indicates that the driver is in an inconsistent or invalid power state.
This appears to be a typical software driver bug and is not likely to be caused by a hardware problem.
The crash took place in the Windows kernel. Possibly this problem is caused by another driver that cannot be identified at this time.
Any help is greatly appreciated!

A:BSOD: Driver Power State Failure ntoskrnl.exe 0x9F

Hi and welcome to the forums.

Seems like a core Kernel level issue.

Things to do:

Run System File Checker to verify/repair the integrity of system files.
Full tutorial here: SFC /SCANNOW Command - System File Checker

Uninstall COMODO Internet Security and replace it with Microsoft Security Essentials - Microsoft Windows
Update it and run a full scan.

Go to Start>Run
Type MSCONFIG and press Enter.
Click on Startup tab, now click on Disable All.
Click Apply and OK. Reboot the system.

In addition, run chkdsk /f to repair corrupt hard drive sectors.
Full tutorial here: Disk Check

If all of the above fails, as a test, I'd suggest you to Enable Driver Verifier to find out which driver/software is causing the BSOD. Once you enable it, expect some frequent BSODs. After 24 hrs, disable the Driver Verifier and re-upload the dump files for analysis.

Let us know if it works.

The below is for information purpose only:

BugCheck Analysis:


Code:
ADDITIONAL_DEBUG_TEXT:
You can run '.symfix; .reload' to try to fix the symbol path and load symbols.

MODULE_NAME: nt

FAULTING_MODULE: fffff80002e56000 nt

DEBUG_FLR_IMAGE_TIMESTAMP: 503f82be

DRVPOWERSTATE_SUBCODE: 3

DEVICE_OBJECT: fffffa8005bca060

CUSTOMER_CRASH_COUNT: 1

DEFAULT_BUCKET_ID: WIN7_DRIVER_FAULT

BUGCHECK_STR: 0x9F

CURRENT_IRQL: 0

LAST_CONTROL_TRANSFER: from fffff80002f3f6d2 to fffff80002ed4fc0

STACK_TEXT:
fffff800`00b9c4c8 fffff800... Read more

Read other 5 answers
RELEVANCY SCORE 104

Been having the occasional blue screen every few hours for the past week or two now, I've been trying to pinpoint exactly which drivers are causing the issue or if it's something more serious. It's a custom built machine and around 18 months old now, so it's not completely unlikely that some of my parts are starting to wear out. (Not overclocking)

Also, I had a hal.dll error associated with the Driver Power State Failure as well, it just didn't fit in the title.

If anyone can give me a hand with this it'd be much appreciated. I've attached the SF files as requested.

A:BSOD Driver Power State Failure ntoskrnl.exe, ntkrnlmp.exe

I"m sorry that I missed this post.
Please reply back if you still need help. I'll reply after work today (after 3pm Eastern time in the US).

Read other 1 answers
RELEVANCY SCORE 102.8

Hi

XPS L502x : 2nd generation Intel Core i7-2720QM processor 2.20 GHz with Turbo Boost
2.0 up to 3.30 GH
8Gb Ram
Windows 7 64 bit

Have been having repeated BSODs lately. Used to get them about once or twice a week but its now a few times a day that it happens.

Have attached the zip file made by the download from this site and will paste the WhoCrashed Report below.

I have tried numerous fixes and nothing has worked...getting desperate.

Thanks in advance guys


System Information (local)
--------------------------------------------------------------------------------

computer name: LAUCHLANMAC
windows version: Windows 7 Service Pack 1, 6.1, build: 7601
windows dir: C:\Windows
CPU: GenuineIntel Intel(R) Core(TM) i7-2720QM CPU @ 2.20GHz Intel586, level: 6
8 logical processors, active mask: 255
RAM: 8499937280 total
VM: 2147352576, free: 1943908352



--------------------------------------------------------------------------------
Crash Dump Analysis
--------------------------------------------------------------------------------

Crash dump directory: C:\Windows\Minidump

Crash dumps are enabled on your computer.


On Sun 3/4/2012 4:14:17 PM GMT your computer crashed
crash dump file: C:\Windows\Minidump\030412-14710-01.dmp
This was probably caused by the following module: ntoskrnl.exe (nt+0x7CC40)
Bugcheck code: 0x9F (0x3, 0xFFFFFA800D8BC4F0, 0xFFFFF80000B9C3D8, 0xFFFFFA800BDDA010)
Error: DRIVER_POWER_STATE_FAILURE
file path: C... Read more

A:Random BSOD : ntoskrnl.exe (nt+0x7CC40) Driver Power State Failure

These were Related to Mbm3DevMt.sys F3607gw Mobile Broadband Device Management Driver from MCCI Corporation.

I would re-install the newest driver available.
The same is true for wwanussf.sys F3607gw Mobile Broadband Module from Ericsson AB

Why 2 Broadband drivers?

Read other 6 answers
RELEVANCY SCORE 102.8

Hello All,

I believe the problem is the result of ntoskrnl.exe because WhoCrashed crash dump analysis says...

This was probably caused by the following module: ntoskrnl.exe (nt+0x75BC0)
Bugcheck code: 0x9F (0x3, 0xFFFFFA800A35EA10, 0xFFFFF80000B9C518, 0xFFFFFA8010D8CCA0)
Error: DRIVER_POWER_STATE_FAILURE

although occasionally it is....

This was probably caused by the following module: ntkrnlmp.exe (nt!KeBugCheckEx+0x0)
Bugcheck code: 0x9F (0x3, 0xFFFFFA800A35EA10, 0xFFFFF80000B9C518, 0xFFFFFA8010D8CCA0)
Error: DRIVER_POWER_STATE_FAILURE


? Win 7 Pro
? x64
? The original OS installed on the system was Win 7 Home
? The OS is a full retail version that I installed
? 5 year old Board and chip
? I have re-installed the OS (always a clean install from a wiped drive) several times. Current install is a little over 1 year old.

? Intel Core i7 860 @ 2.8GHz
? NVidia GeForece GTX 650 Ti Boost
? Dell Studio XPS 8100 Motherboard w/ Intel H57 Chipset
? Diablotek Pro Series 550w Power Supply

? Dell
? Studio XPS 8100

Desktop

I have expanded and replaced a number parts on the system since originally purchased. I currently have 3 SATA Drives and the DVD drive attached to the motherboard as well as an external drive attached to the external eSata port. 12GB RAM. My OS resides on its own SSD and all files are stored on other drives. I am not overclocking. The only security I am running is MS security essentials.

Let me know if there is any additiona... Read more

A:BSOD Regularly WhoCrashed says ntoskrnl.exe Driver Power State Failure

Hi

Can you update the driver to your Broadcom NetLink (TM) Gigabit Ethernet from Broadcom?
Let us know the result.

Read other 3 answers
RELEVANCY SCORE 101.6

Hello and thanks for letting me post on this awesome forum!!!!

I am fixing a family members computer and it has stumped me. I have tried everything that I can find online related to my problem outside of reinstalling but I think it could be a hardware (power or memory) issue from what i read and a reinstall wouldnt fix it.

Driver_Power_State_Failure

I cannot trigger the BSoD of cue. Ive tried quite a bit, bringing it back from sleep, full load, no load, Skyrim, and different video cards.

I have been using Bluescreenviewer / myeventviewer to give me some incite but I couldn't find anything that would help my particular problem. So i present it to the people that know more then me, the online community. I followed the BSoD posting rules but let me know. Ill be checking back frequently.

Thanks again.

PS this computer is having raid issues. I get "Degraded NVIDIA mirror 931.51G" red flashing error for a couple seconds during boot. I dont know if this is related but BSoD's did not start at exactly the same time, but quite a bit of time after, I am told.

A:Random BSoD, Driver Power State Failure, reports blame ntoskrnl.exe

A few issues

1-asacpi.sys

The pre 2009 version of this driver is a known BSOD cause.





Quote:
Please visit this link: Asus tek computer inc. -support- drivers and download p7p55d le

ASUSTeK Computer Inc. -Support- Drivers and Download P7P55D LE
ASUSTeK Computer Inc. - Motherboards- ASUS P5K-VM

Scroll down to the utilities category, then scroll down to the "atk0110 driver for windowsxp/vista/windows 7 32&64-bit" (it's about the 12th item down).

Download and install it.

Go to c:\windows\system32\drivers to check and make sure that the asacpi.sys file is date stamped from 2009 or 2010 (not before).


2-These were all related to your NVIDIA nForce RAID Driver. Yours is from 2006. Update to current of remove.

3-Old drivers

Code:
ASACPI.sys 3/27/2005 10:30:36 PM
nvrd64.sys 11/10/2006 4:18:39 PM
SiWinAcc.sys 6/14/2007 8:02:02 PM
SiRemFil.sys 6/20/2007 3:42:10 PM
SI3132.sys 10/3/2007 2:39:29 PM
dump_nvstor64.sys 1/25/2008 11:01:22 PM
nvstor64.sys 1/25/2008 11:01:22 PM
nvm62x64.sys 10/17/2008 5:01:06 PM
How To Find Drivers:




Quote:
- search Google for the name of the driver
- compare the Google results with what's installed on your system to figure out which device/program it belongs to
- visit the web site of the manufacturer of the hardware/program to get the latest drivers (DON'T use Windows Update or the Update driver function of De... Read more

Read other 3 answers
RELEVANCY SCORE 95.2

Hey Guys,

First off, Happy 2011! I've been experiencing the BSOD every now and then and I've finally had enough of it. So I'm hoping you guys can help me.

Thanks in advance!

OS - Windows 7
x64
Windows Vista originally installed
Full Retail Version
2 Years old
Around 4 months old
CPU - Intel Core 2 Duo CPU T9400 @ 2.53GHz
Video Card - NVIDIA GeForce 9800M GS
MOtherboard - Not sure, but I have an ASUS laptop
Power Supply - Not sure either.

A:BSOD - Drive Power State Failure

Hello,

There are no dumps recorded in that report; I don't see any in your Minidump folder either.

I see evidence of BSODs on November 16, September 26, and September 20:
Code:
Event[4674]:
Log Name: Application
Source: Windows Error Reporting
Date: 2010-11-16T17:29:27.000
Event ID: 1001
Task: N/A
Level: Information
Opcode: Info
Keyword: Classic
User: N/A
User Name: N/A
Computer: Louis-PC
Description:
Fault bucket , type 0
Event Name: BlueScreen
Response: Not available
Cab Id: 0

Problem signature:
P1:
P2:
P3:
P4:
P5:
P6:
P7:
P8:
P9:
P10:

Attached files:
C:\Windows\Minidump\111610-37674-01.dmp
C:\Users\Louis\AppData\Local\Temp\WER-17853316-0.sysdata.xml

These files may be available here:
C:\Users\Louis\AppData\Local\Microsoft\Windows\WER\ReportArchive\Kernel_0_0_cab_06e1a826

Analysis symbol:
Rechecking for solution: 0
Report Id: 111610-37674-01
Report Status: 0
Event[10533]:
Log Name: Application
Source: Windows Error Reporting
Date: 2010-09-26T11:01:27.000
Event ID: 1001
Task: N/A
Level: Information
Opcode: Info
Keyword: Classic
User: N/A
User Name: N/A
Computer: Louis-PC
Description:
Fault bucket X64_0x9F_3_IMAGE_snp2uvc.sys, type 0
Event Name: BlueScreen
Response: Not available
Cab Id: 0

Problem signature:
P1:
P2:
P3:
P4:
P5:
P6:
P7:
P8:
P9:
P10:

Attached files:
C:\Windows\Minidump\092610-70574-01.dmp
C:\Users\Louis\AppData\Local\Temp\WER-102991-0.sysdata.xml
C:\Users\Louis\AppData\Local\Te... Read more

Read other 1 answers
RELEVANCY SCORE 95.2

I forgot to copy the information i had in the window that pop'd up.
I have a dell n5110 and am running windows 7 64bit with intel core i5.

I believe that this has something to do with my wireless drivers(or is affecting it somehow.)
Any help would be appreciated.
Thanks.

A:BSOD,Drive power state failure.

Of it helps,0x0000009F is the code that i believe popped up.

Read other 4 answers
RELEVANCY SCORE 95.2

My Mother was trying to plug in her iphone into her laptop a few days ago. Her laptop is HP DV7-12?? (sorry I don't know the full numbers since I'm not at my parents house anymore).

She has a Logitech tackball mouse plugged in so I unplugged it. Well even trying the other two usb hubs doesn't work. After that, I plugged in the logitech mouse back into the same usb.. It didn't work..

After that I tried powering down the laptop. but after 13m (ruffly), it bsod with a drive power state failure. with a 9f problem..

I've googled and they've told me about looking at the minidump and from that it would show what was wrong.. I don't know how to read it, and nor do I have the debugging tool.

So, I was wondering if someone could read it and help me with the problem.

system specs for her laptop is
win vista 64bit prem.
6gb ram,
intel cpu 2.2ghz
Nvidia 9600m GT

I've ran in safe mode and everything works like a charm, but in windows.. I have to make sure it's plugged in before I boot into vista for it to work.


Thank You

A:bsod drive power state failure

Both are 100009F, pointing to different items:

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 1000009F, {4, 258, fffffa80054db040, 0}

Unable to load image \SystemRoot\system32\DRIVERS\hpdskflt.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for hpdskflt.sys
*** ERROR: Module load completed but symbols could not be loaded for hpdskflt.sys
Probably caused by : hpdskflt.sys ( hpdskflt+29e1 )

Followup: MachineOwner
---------

0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

DRIVER_POWER_STATE_FAILURE (9f)
A driver is causing an inconsistent power state.
Arguments:
Arg1: 0000000000000004, The power transition timed out waiting to synchronize with th... Read more

Read other 4 answers
RELEVANCY SCORE 95.2

This has been the first crash I've gotten in ages. Basically I was just playing New Vegas on my computer, and the game randomly locked up during normal gameplay and gave me that error. I uploaded the crash dump file
http://www.mediafire.com/?sidtlnt7tixrf00
but not sure what was the cause of the issue.
Also, I tried using readyboost today for the first time in a while, that may have been the issue because I'm unsure about my memory card reader driver for 7.

A:Drive Power State Failure BSOD

Please visit the PC Manufacturer's website and download/install the most recent version of the Media Card Reader drivers for Win7 and your system. The BSOD points to o2sdx64.sys - a component of your Memory Card Reader driver by O2Micro.

BSOD BUGCHECK SUMMARY

Code:

Built by: 7600.16617.amd64fre.win7_gdr.100618-1621
Debug session time: Wed Oct 20 10:39:29.502 2010 (UTC - 4:00)
System Uptime: 5 days 10:25:50.264
*** WARNING: Unable to verify timestamp for o2sdx64.sys
*** ERROR: Module load completed but symbols could not be loaded for o2sdx64.sys
Probably caused by : o2sdx64.sys
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0x9F
PROCESS_NAME: audiodg.exe
Bugcheck code 0000009F
Arguments 00000000`00000003 fffffa80`05926050 fffff800`04526748 fffffa80`07030e10
??????????????????????????????????????????????????????????????????????????????????????``

Read other 1 answers
RELEVANCY SCORE 95.2

I recently installed some Windows updates on my new computer, and after the first boot with the updates my computer froze and I got a BSOD saying "Drive Power State Failure"

Here is the attached .dmp file

Thank you

A:Drive Power State Failure - BSOD

Hello Dominicoben

► You are getting a STOP 0x0000009F: DRIVER_POWER_STATE_FAILURE .

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa8005fb8060, fffff80000b9c4d8, fffffa800397b760}

*** WARNING: Unable to verify timestamp for win32k.sys
*** ERROR: Module load completed but symbols could not be loaded for win32k.sys
Probably caused by : usbhub.sys
I would suggest you to turn on USB selective suspense, to see if it is caused by the driver or the hardware itself.
USB Selective Suspend - Turn On or Off

► If there any devices attached in the USB ports (other than keyboard and mouse), remove those and see if the situation changes.

► And, while getting windows updates, get all the updates. Your Default Hub Driver for USB is very old, compared to the other few drivers. So the chance of incompatibility is there.

Code:
lmvm usbhub
start end module name
fffff880`06e92000 fffff880`06eec000 usbhub (pdb symbols) c:\symcache\usbhub.pdb\295DCA65F67B44BF8DD26C3B6D89A6F71\usbhub.pdb
... Read more

Read other 1 answers
RELEVANCY SCORE 95.2

My laptop is fairly new and should not be giving me the issues that it does. It suddenly started blue screening for no reason. I don't have to be doing anything, it will just crash for no reason. I have done a full system wipe and it still crashes. I need help.

A:BSOD for power drive state failure

Hello Lawndart.

This particular version of display driver (the latest one) is problematic.

Code:
Irp is active with 4 stacks 2 is current (= 0xfffffa800720d498)
No Mdl: No System Buffer: Thread 00000000: Irp stack trace.
cmd flg cl Device File Completion-Context
[ 0, 0] 0 0 00000000 00000000 00000000-00000000

Args: 00000000 00000000 00000000 00000000
>[ 16, 2] 0 e1 fffffa8009879850 00000000 fffff8800621c084-fffffa800b5e47c0 Success Error Cancel pending
*** WARNING: Unable to verify timestamp for ACPI.sys
*** ERROR: Module load completed but symbols could not be loaded for ACPI.sys
\Driver\ACPI nvlddmkm
Args: 00000000 00000001 00000001 00000000
[ 16, 2] 0 e1 fffffa800a954040 00000000 00000000-00000000 pending
\Driver\nvlddmkm
Args: 00000000 00000001 00000001 00000000
[ 0, 0] 0 0 00000000 00000000 00000000-fffffa800be3e3c0

Args: 00000000 00000000 00000000 00000000
--------------------------------------------------------------------------------------------------------
start end module name
fffff880`060f1000 fffff880`06b8f000 nvlddmkm T (no symbols)
Loaded symbol image file: nvlddmkm.sys
Image path: \SystemRoot\system32\DRIVERS\nvlddmkm.sys
Image name: nvlddmkm.sys
Timestamp: Sat Dec 29 12:17:52 2012 (50DE9218)
CheckSum: 00A7F96C
ImageSize: 00A9E000
Translations: ... Read more

Read other 9 answers
RELEVANCY SCORE 95.2

This morning didn't start well for me. It had the following events.

1) Volume wouldn't work.
2) Volume Mixer freezes/not responding when trying to move the volume slider
3) Device Manager Froze when messing with the audio section
4) Windows said there were updates and it needed to be restarted, when updates supposedly finished the computer "Restarted" and it say on the restarting screen for about 5 minutes then it BSoD's

The following is the files that you guys require. Also I have no AV just Defender and Windows Firewall. In the past in Windows 7 "AMD High Definition Audio" froze my volume control so I had to disable that, in this case it did NOT help.

NOTE: I do not have an SSD nor do I put it into sleep. I am also dual booting windows 7 and 8. Although in the past it BSoD'd when it was only windows 8.

Also last night I installed "BlackX" software, it's a hotswap dock with a USB cable that you can just plop a HDD in and press the power button and view the files on the drive.

I also looked up the BIOS for my motherboard, and this was on the download page:

It says windows 8 ready, but I don't know if it was already Windows 8 ready or that's the NEW drivers. I don't know how to check the date of my BIOS nor does it specify a date for the supposed new BIOS on their site.

I am also on Windows 8.1, I have connections. I also have no sound, not sure why.

A:Drive Power State Failure BSOD

I hate to bump this but I wish to at the very least have a general statement / reply.

Read other 3 answers
RELEVANCY SCORE 95.2

Hello,
There have been many problems since installing W8 from the Shutdown and Restart button being unresponsive to USB 3.0 failures to nvidia driver issues.

Anyhow, I've had numerous BSOD since upgrading from W7 Pro, so I did a clean install of Win 8 Pro afterwards. But now I've encountered another recent issue, a drive power state failure. The problem occurred when I was removing my USB 3.0 PCI card and dusting off any dirt because I've come to believe the card is dead (device manager shows a yellow ! beside Renesas usb 3.0 xHCI). I booted the computer and when I snapped the side plate back on to the case I get the error.

Any help would be appreciated.

A:BSOD, drive power state failure

Welcome
It takes several BSODs to ascertain the definitive cause of your problem. You have given us one report and it mentions a driver. It is a Microsoft Driver and not the true cause. After a few more BSODs report again.

Read other 1 answers
RELEVANCY SCORE 94.4

I'm getting a BSOD pretty much every time I shutdown the PC. Has only just started happening in the last couple of weeks.

DRIVER_POWER_STATE_FAILURE
caused by driver: ntoskrnl.exe

I've attached the SFDiagnostic here - thanks.

A:BSOD - ntoskrnl.exe "driver power state failure" at shutdown

Hi thedriver.

The BSODs are caused by REALTEK 2832U USB Driver (c:\windows\system32\drivers\rtl2832uusb.sys)





Quote:
Windows Error Reporting: Fault bucket X64_0x9F_3_POWER_DOWN_IMAGE_RTL2832UUSB.sys, type 0
Event Name: BlueScreen
Response: Not available
..........;Analysis symbol: X64_0x9F_3_POWER_DOWN_IMAGE_RTL2832UUSB.sys
............



Code:
BugCheck 9F, {3, fffffa8008604060, fffff80001f4a518, fffffa800ae4e710}

*** WARNING: Unable to verify timestamp for RTL2832UUSB.sys
*** ERROR: Module load completed but symbols could not be loaded for RTL2832UUSB.sys
Probably caused by : RTL2832UUSB.sys

Followup: MachineOwner
---------
And the driver is old enough.

Code:
fffff880`07778000 fffff880`07785000 RTL2832UUSB T (no symbols)
Loaded symbol image file: RTL2832UUSB.sys
Image path: RTL2832UUSB.sys
Image name: RTL2832UUSB.sys
Timestamp: Wed May 04 14:05:12 2011 (4DC10FC0)
CheckSum: 0000ACF2
ImageSize: 0000D000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
Some information about what this driver does: Realtek
Unfortunately I am unable to search an appropriate update for you. I hope you know the sources to get it, as you are using it.

If you can, update the driver. Otherwise, dont use it.

Read other 3 answers
RELEVANCY SCORE 94.4

Hi Folks,

I really hope you can help me, I followed the instructions to create the attachement.

What I know so far is that this machine has BSOD'd several times...The last 2 times a ultilty called BlueScreenViewer.exe says it's due to "Driver power state failure" caused by: ntoskrnl.exe

I checked event viewer for the time mentioned 6/17/2012 11:29:02 pm and it says there is system error "source:Bug Check" at that exact time

For anti-virus I have MS Security Essentials. For Spyware, I have Spybot S&D.
I use with Workstation 7 as a study too so it has hosed my VMs which is very disappointing. I would really like to root cause this to continue with confidence...

I know you hear this all the time...but... please help! I don't mind collecting info and checking into things, I am just out of my element a little here.

I looked throug the results of the permon report and it seems clean for the most part.

Thanks in advance,

Jay

A:BSOD "Driver power state failure" caused by: ntoskrnl.exe

Is there anything else I can do to help action this post? Thanks

Read other 9 answers
RELEVANCY SCORE 93.6

Hi everyone,

I've had my asus laptop for about a year, but the BSODs just started recently. What seems to trigger it is my wifi connection stops working and I get a "limited connectivity" error and it is definitely not the router that isn't working because all other computers' wifi connection runs fine. Resetting my adapter by disabling it and enabling it does not fix the problem because it gets stuck at the enabling adapter step. So the only choice I have is to reboot my laptop. When I do this, it hangs at the shutting down step for awhile like 10-15mins and I get the blue screen error with the driver power state failure.
(Also I'm pretty sure my wireless adapters are up to date).

I'm also running symantec endpoint protection

Any help would be appreciated!

A:BSOD when wifi stops working, driver power state failure

Welcome
Your reports are clear. The BSODs are caused by your Antivirus/Firewall.
Make a system restore point. Download Microsoft Security Essentials and use the Windows Firewall as a test. Lets see how that goes.

Read other 3 answers
RELEVANCY SCORE 93.2

Lately my 1.5 year old ASUS CM6870 Desktop running Win8.1 started to give me the BSOD with the following two error messages: Page Fault in Non_Page Area; and Drive Power State Failure. Occasionally I will get the sudden BSOD and this B stands for Black with no cursor or message showing. In about 10 seconds the monitor will display a message saying it is going into inactive mode. I pressed the desktop power button, the system just shut down. Two days ago at log off Windows was doing update and at 30%, everything was frozen. Left it on the whole night, same screen the next morning. Need to depress the power button to shut down the system although Windows said I can't shut down the PC while it's doing an update. That's about the symptoms I can recap for now. Zip file attached as instructed. Thanks.

A:BSOD re Page Fault and Drive Power State Failure

There is no dump file. Please check your minidump folder for it. When you find it, upload it. If you are using CCleaner, please strop as it deletes minidumps.

Read other 1 answers
RELEVANCY SCORE 93.2

Hi everyone,

I am using a Toshiba Satellite A505-S6025 laptop running Windows 7 Pro 64-bit, 4GB RAM, Nvidia 310M graphics card.

Things have been working well for a couple of months until yesterday, after I installed a Western Digital Mybook World Edition (1TB) and the most recent Windows updates. After these installations, I have been having 2 problems:

1.) First thing I noticed is that shutdown takes forever, and ends with a BSOD with DRIVER_POWER_STATE_FAILURE message.

2.) Secondly, none of my USB devices are being recognized anymore. Sometimes when I have these devices plugged BEFORE powering Windows on they get recognized properly, but if I plug any USB devices after Windows loads I do not get any recognition at all.

I've tried updating to the latest video drivers, BIOS, and uninstalling the programs that came with the WD drive (MioNet and WD Anywhere Backup) but the problems haven't gone away.

Analyzing the memory dump led to this message:

On Thu 5/13/2010 2:28:10 PM your computer crashed
This was likely caused by the following module: ntoskrnl.exe
Bugcheck code: 0x1000009F (0x4, 0x258, 0xFFFFFA8003B85040, 0xFFFFF80000B9C510)
Error: Unknown
Dump file: C:\windows\Minidump\051310-17097-01.dmp
file path: C:\windows\system32\ntoskrnl.exe
product: Microsoft? Windows? Operating System
company: Microsoft Corporation
description: NT Kernel & System
The crash took place in a standard Microsoft module. Your system configuration may be incor... Read more

A:USB device not detected, BSOD Drive Power State Failure

Welcome!

First, some basic troubleshooting tips. Disconnect the new hard drive and do a system restore to get to a point before the troubles.

Uninstall the Toshiba HDD Protection Program.

BSOD BUGCHECK SUMMARY
Code:

Built by: 7600.16539.amd64fre.win7_gdr.100226-1909
Debug session time: Thu May 13 10:26:56.095 2010 (GMT-4)
System Uptime: 0 days 0:34:58.733
BugCheck 1000009F, {4, 258, fffffa8003b85040, fffff80000b9c510}
Probably caused by : ntkrnlmp.exe ( nt!KiSwapContext+7a )
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
??????????????????????????????????????????????????????????????????????????????????????
Built by: 7600.16539.amd64fre.win7_gdr.100226-1909
Debug session time: Thu May 13 05:53:57.120 2010 (GMT-4)
System Uptime: 0 days 0:56:05.743
BugCheck 1000009F, {4, 258, fffffa8003b85b60, fffff80000b9c510}
Probably caused by : ntkrnlmp.exe ( nt!KiSwapContext+7a )
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
??????????????????????????????????????????????????????????????????????????????????????
Built by: 7600.16539.amd64fre.win7_gdr.100226-1909
Debug session time: Thu May 13 04:57:24.180 2010 (GMT-4)
System Uptime: 0 days 4:23:15.413
BugCheck 1000009F, {4, 258, fffffa8003b85040, fffff80000b9c510}
Probably caused by : ntkrnlmp.exe ( nt!KiSwapContext+7a )
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
??????????????????????????????????????????????????????????????????????????????????????
Built by: 7600.16539.amd64fre.win7_gdr.100226-1909
Debug session time: Wed May 12 23:21:56.142 20... Read more

Read other 7 answers
RELEVANCY SCORE 92.4

I apologize in advance if this is a duplicate thread to a problem already solved previously.

Two months ago, I purchased this laptop (Alienware M17x R3) and was met with strange problems some time after owning it. An error code for memory failure, refusal to boot, BSOD with the error of DRIVER_IRQL_NOT_LESS_OR_EQUAL and SYSTEM_THREAD_EXCEPTION_NOT_HANDLED. Not sure what to do, I didn't do much of anything, except check my RAM chips for contact damage, and a swapping of positions was performed. So far, those particular error messages have not happened again, except for a DRIVER_POWER_STATE_FAILURE. These happen seemingly at random, but occur more frequently when the computer is under graphics stress, such as in a Starcraft 2 match.

I have, per the posting suggestions, attached relevant files.

Thanks.

A:Driver Power State Failure, ntoskrnl.exe?

Welcome to SevenForums.

Here's an output of your recent BSOD dump file:

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa800e3c6a10, fffff80000b9c3d8, fffffa800ed0fe10}

Unable to load image \SystemRoot\system32\DRIVERS\nvlddmkm.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
Probably caused by : pci.sys

Followup: MachineOwner
---------

0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

DRIVER_POWER_STATE_FAILURE (9f)
A driver has failed to complete a power IRP within a specific time (usually 10 minutes).
Arguments:
Arg1: 000000000000... Read more

Read other 9 answers
RELEVANCY SCORE 92.4

I have a 13 days old win7 pro RTM x64 system. In the past two days I had
two BSODs of similar fashion:

The machine was running for several hours at that point, and suddenly the
blue screen pops up. I wasn't really pushing the system, just browsing.

The crash dump is like this in both cases:






Quote:
This was likely caused by the following module: ntoskrnl.exe
Bugcheck code: 0x9F (0x3, 0xFFFFFA8003B4B050, 0xFFFFF80000B9C518, 0xFFFFFA80052E0E10)
Error: DRIVER_POWER_STATE_FAILURE
file path: C:\Windows\system32\ntoskrnl.exe
product: Microsoft? Windows? Operating System
company: Microsoft Corporation
description: NT Kernel & System
The crash took place in a standard Microsoft module. Likely the culprit is another
driver on your system which cannot be identified.



I'd appreciate any help.

A:ntoskrnl Driver power state failure

I had the same problem
I tried everything nothing worked
I saved everything in safe mode and did a re-install

But do some searching on Google
one thing I didnt try was replacing ntoskrnl.exe with one downloaded from the net
I will search for mine & post it here for you here

Also do some searching on here

Read other 9 answers
RELEVANCY SCORE 91.6

Hi all,

I was hoping to bring the 'big guns' on this forum to bear on my problem. My friend has an Asus UX32A notebook with Windows 8. To provide some back story (the meat of the problem is after this paragraph if you want to skip)...

It is brand new with hardly anything installed on it besides Norton 2013 and Office. It would freeze about 60 seconds after start up, for a good long while, and it seemed to get worse over time. I have done a LOT of things to it in the last two days - uninstalled Asus bloatware (which was also causing a black screen on startup problem), updated just about every driver and BIOS, disabled fast start up, disabled 'dynamictic' via cmd prompt, disabled all non-Windows services and then progressively enabled them to try to isolate a rogue one. I THINK I might have fixed it (in the end I left 7 services disabled - two Intel Management, Intel Dynamic application, Intel ME service, as well as Wireless PAN, Skype updater and Sony PC companion. I have no idea if it's one of these but the system seems not to freeze now and I have reached the end of my patience anyway). It might seem like too much but it was very difficult because e.g. to test the effect of one change I would have to restart, and the laptop would not restart because of the black screen issue, or would immediately freeze. It was very frustrating and I had to work from safe mode to start with, but now it seems to behave better.

But...

I have had several hang-during-reboots today, forcing ... Read more

A:Driver Power State Failure; ntoskrnl.exe; ntkrnlmp.exe

Check out the forum thread here "ntoskrnl.exe" BSOD - Windows 7 Help Forums

Since it is new or relatively new a complete reinstall using the ASUS recovery is recommended. That I saw on several searches.

Read other 1 answers
RELEVANCY SCORE 90.4

Hello,
I've spent days researching online - I've tried to find if I had any drivers to update by going to my Device Manager but all "update driver" results I get are the same: they are up to date.
My minidump file: https://drive.google.com/file/d/0Bz9...it?usp=sharing .

DRIVER_POWER_STATE_FAILURE
Bug check code: 0x0000009f
Parameter 1: 00000000'00000003
Parameter 2: fffffa80`07d0ba10
Caused by Driver: ntoskrnl.exe
Caused by address: ntoskrnl.exe+75bc0
File description: NT Kernel & System
Crash address: ntoskrnl.exe+75bc0

Windows 7 Professional x64 Service Pack 1
Lenozo Ideapad z500
8gb ram, NVIDIA GEFORCE 2gb
Intel Core i7

Any help is greatly appreciated!

A:Windows 7 Pro: Driver Power State Failure ntoskrnl.exe 0x9F

from the research Ive done previously etc; I do believe the ntoskrnl.exe possibly leads to ram issue. I would test the ram by running memtest86+ from the following link: its best to let it run overnight if possible and to run it several times to make certain it shows accurate results as sometimes errors wont show up right away. Here is the link to that:

Memtest86+ - Advanced Memory Diagnostic Tool

If you get any errors from the test; then its likely you have one or more bad ram sticks

Read other 9 answers
RELEVANCY SCORE 88.4

Win7 laptop running fine, suddenly 2 BSODs today, within an hour. First occurred while surfing (firefox), second occurred without any keyboard/mouse activity. No new hardware installed since new hard drive about a month ago. SF attached. TIA

A:Random BSODs, ntoskrnl, driver power state failure reports on minidump

Sorry for the late reply, Your dump files are not opening for me.
But you should remove some add ons to firefox, specially the adxloader.dll





Quote:
Event[10757]:
Log Name: Application
Source: SideBySide
Date: 2012-10-03T15:36:32.000
Event ID: 9
Task: N/A
Level: Error
Opcode: N/A
Keyword: Classic
User: N/A
User Name: N/A
Computer: RWT-PC
Description:
Activation context generation failed for "C:\Users\RWT\AppData\Roaming\DocuSign\DocuSign Ink\adxloader.dll.Manifest".Error in manifest or policy file "C:\Users\RWT\AppData\Roaming\DocuSign\DocuSign Ink\adxloader.dll.Manifest" on line 2. The manifest file root element must be assembly.


It may be the cause of the crash while using firefox.

Just a question, when the keyboard and mouse was inactive and you got the crash, was the Cyberlink editing program in use? The event log says so, and actually that program failed there.

You should update the nvidia display driver, too.

Code:
Driver c:\windows\system32\drivers\nvlddmkm.sys (8.17.12.7527, 10.09 MB (10,583,656 bytes), 6/23/2011 6:38 PM)
Update your WiFi driver.

Code:
Driver c:\windows\system32\drivers\netw5s32.sys (13.1.1.1, 6.44 MB (6,755,840 bytes), 1/13/2010 3:36 PM)
Update ethernet controller driver.

Code:
Driver c:\windows\system32\drivers\yk62x86.sys (11.43.1.3, 310.28 KB (317,728 bytes), 5/26/2011 2:29 AM)
Free up the startup.
Click on the Start button
Type “msconf... Read more

Read other 3 answers
RELEVANCY SCORE 87.6

http://m.bestofmedia.com/sfp/images/...il-100x100.jpg


I hope someone can help been on this problem for a week now.

I have an external synth that conects via usb My problem is when i switch off the nord the usb ports crash and any new connection is not recognised until i restart my computer which when i do hangs on the shutdown page for about 10 minutes the i get bsod with error driver state failure or bad pool header.

I can start my computer then turn on and off the nord with no issues the problem only happens when i use it in cubase 7 as a midi track even if no midi signal is sent to the nord. The problem is when i turn off the nord by the power button the driver disconnects then if i try to reconnect the nord nothing happens in the device manager all usb that are still connected work but any new connection is not seen.

I have done a fresh install of windows 7 64bit updated all drivers for everything & windows updates.

I have tried disconnecting all usb devices and still the same problem. Im not over clocking or under clocking. I have tried a different usb lead, used various usb ports, external powered usb ports.

The drivers i have installed are nord a1 midi, clavia usb 3.02 driver & clavia compostite usb driver.The latest ones.

The units was working fine until about 2 weeks ago where i was able turn the unit on and off using cubase with no problems.

Hope we can find a solution to the problem.

Read other answers
RELEVANCY SCORE 85.2

Hi,

I've been browsing the site and the internet for a sollution to my problem, but can't seem te find it. There are similar postings, but they're always just a little different. So that's why i posted the new thread.

Since a couple of days i've been experiencing troubles shutting down my PC and using my USB ports. It started when i tried to log onto my work from home. It failed and the IT guy from work told me to reinstall citrix reciever. So I did and I was able to work from home. After finishing and logging out (to get back to my own PC) I found that my USB portst didn't work anymore. I tried rebooting, but af 10 minutes of "shutting down" I got a blue screen: Driver Power State Failure with code 1000009f.

I did the following:
- tried system restore - it failed with different time stamps
- update drivers - they were all up to date the system said
- Malware Bytes, CC Cleaner, MS Essentials, Hitman pro - Did them all, had some minor stuff, fixed that, problem remained.
- SFC/scannow - no problems
- Memory check - no problems

As it is now, the only update I have left is the update to WIN10. However it has tried and failed during a few of the reboots, so that doesn't seem to be and option.

After try all different kinds of things from a lot of posts I decided to refresh my windows install. Did a lot of updating and still the problem remains. Although I now found out that USB devices that are plugged in upon startup work. Once I unplug en replug them, t... Read more

A:BSOD Driver power state failure when shutting down /failure USBports

Are you still having BSOD problem?

Read other 1 answers
RELEVANCY SCORE 85.2

So I have a pirated windows 8.1 which I have been using for more than a year now. Since the past one week my drivers ( especially the internet driver) keeps crashing and stops detecting any networks. Upon an attempted restart I get the Bsod for which I have attached the files ( All the minidumps.) I run a Dell 5521 R and have updated the drivers, uninstalled and reinstalled them too. Kindly help ASAP as I require my wifi urgently tomorrow.
Note: After restart the drivers get refreshed automatically and start working for sometime. And then the same issue. Please help.VATSAL-Tue_02_09_2016_101910_61.zip

Read other answers
RELEVANCY SCORE 82.4

Hi everyone. This is my first post on the forum, so I really appreciate any help that anyone may be able to offer. I have been receiving a drive state power failure error since clean installing Windows 8 on my system. I suspect it may be a bad driver or something, but I am not sure. I already set my system to not hibernate or sleep and I tried updating my BIOS and removing a third-party Spyware protection program, but the error occurred again. I followed the instructions and have attached my memory dump information.

Thanks again for your help!

A:Drive Power State Failure.. not sure why!

The minidumps seem to be pointing at the file: pci.sys which is the NT Plug and Play PCI Enumerator:

Driver Reference Table - pci.sys

This file could be corrupt so make sure you download the latest manufacturers chipset motherboard drivers for Windows 8 64bit:

ASUS - Motherboards- ASUS P8Z68-V PRO/GEN3

Also make sure you have all the Windows 8 updates until you can no longer be updated.

I have also found two drivers that you might consider updating or un-installing/removing if un-needed:

HECIx64.sys - Intel Management Engine Interface: Driver Reference Table - HECIx64.sys
P17.sys - Creative SB Audigy LS: Driver Reference Table - P17.sys

-cheers

Read other 3 answers
RELEVANCY SCORE 82

I have windows 8 installed on my home computer. The computer keeps shutting down on it's own and saying "Driver Power State Failure". Can someone look at my BSOD Minidump files and give me an idea of what could be causing this problem. I have tried to save the minidump files into a zip file, but it brings up an error not allowing me to do this. Hopefully the text file from Blue Screen view is enough to figure this out. Thanks.

==================================================
Dump File : 021413-31262-01.dmp
Crash Time : 2/14/2013 11:00:19 AM
Bug Check String : DRIVER_POWER_STATE_FAILURE
Bug Check Code : 0x0000009f
Parameter 1 : 00000000`00000003
Parameter 2 : fffffa80`1c00e600
Parameter 3 : fffff800`49f58920
Parameter 4 : fffffa80`1b38fa00
Caused By Driver : atapi.sys
Caused By Address : atapi.sys+3474
File Description :
Product Name :
Company :
File Version :
Processor : x64
Crash Address : ntoskrnl.exe+7a040
Stack Address 1 :
Stack Address 2 :
Stack Address 3 :
Computer Name :
Full Path : C:\Windows\Minidump\021413-31262-01.dmp
Processors Count : 8
Major Version : 15
Minor Version : 9200
Dump File Size : 905,408

Dump File : 021313-22042-01.dmp
Crash Time : 2/13/2013 8:27:48 PM
Bug Check String : DRIVER_POWER_STATE_FAILURE
Bug Check Code : 0x0000009f
Parameter 1 : 00000000`00000003
Parameter 2 : fffffa80`09a0d060
Parameter 3 : fffff803`f9af1920
Parameter 4 : fffffa80`09afb010
Caused By Driver : ntoskrnl.exe
Caused By Address : ntoskrnl.exe+7a040
Fi... Read more

A:BSOD-Power Failure state

what are you running
video card brand and model
cpu
m/board
ram
power supply
brand
model
wattage

check the listings in the bios for 12v line voltages and cpu temperatures and post them
 

Read other 3 answers
RELEVANCY SCORE 82

Hi Folks,

1st ... thanks for being there and your efforts.

This bug has been driving me mad now for some time and I am unable to clear it myself.

My system is a roll your own running Windows 7 Ultimate x64 from Day 1 (about 18 months ago) on an original Retail load. A complete hardware profile is included in the attachments (via Belarc Advisor). The C drive is a 128 GB Kingston SSD.

I'm really looking forward to seeing the back end of this problem as well as your diagnosis.


many many thanks in advance

A:BSOD - Power State Failure

There is only 1 dump in the`upload is the PC set to overwrite the previous dumps?
The key is to look for patterns in the dumps, that's hard to do on a single dump but there is some interesting things here

It appears you have a AMD Athlon(tm) II X4 645 Processor
But Windows is reporting Windows 7 Kernel Version 7601 (Service Pack 1) MP (3 procs) Free x64 the 3 procs part would mean 3 cores, in task manager on the performance tab how many CPU graphs are displayed 3 or 4?

These three Asus drivers are known to cause issues on WIN7 x64
ASACPI.sys Wed Jul 15 23:31:29 2009 (4A5E9F11)
AsIO.sys Mon Aug 3 03:03:16 2009 (4A768BB4)
AsUpIO.sys Sun Jul 5 22:21:38 2009 (4A515FB2)
They are part of the Asus AI suite, see if there is a update for your board on the Asus site.> ASUSTeK Computer Inc. -Support- Drivers and Download

wacommousefilter.sys Fri Feb 16 13:12:17 2007 From 2007 this is not a Win7 driver.
Wacom(tablet) Mouse Filter > Drivers | Wacom Americas

mv2.sys Wed Feb 6 16:02:40 2008 Another Vista driver

UltraVnc miniport driver2 > Download - UltraVNC - VNC - Remote Support Software - Remote Desktop Control - VNC - Free - OpenSource


Code:
**************************Mon Oct 1 14:52:51.948 2012 (UTC - 4:00)**************************

Microsoft (R) Windows Debugger Version 6.12.0002.633 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.
Loading Dump File [C:\U... Read more

Read other 19 answers
RELEVANCY SCORE 82

BSoD with Power State Failure
Usually occurs when idle, I come back to find my computer has shut down and on restart I get an error message:
Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7601.2.1.0.256.48
Locale ID: 1033

Additional information about the problem:
BCCode: 9f
BCP1: 0000000000000003
BCP2: FFFFFA8008599A00
BCP3: FFFFF80003FED3D8
BCP4: FFFFFA80093D1010
OS Version: 6_1_7601
Service Pack: 1_0
Product: 256_1

Ran Windows Debug on the dump file and it says BSoD probably caused by ntoskrnl.exe, but how do I go about fixing this?

Thanks!


Specs:
? OS (original) - Windows 7
? x64
? retail version
? Age of system (hardware): 1 week
? Age of OS installation - 1 week

? CPU - Intel 2500K
? Video Card - Radeon HD 6870
? MotherBoard - MSI P67 G43 B3
? Power Supply - OCZ Modstream 600W

Self Build

A:BSoD - Power State Failure

Have you tried rebooting to last known good?

Read other 1 answers
RELEVANCY SCORE 82

This is a Brand New Build as in Built Yesterday. All was well till I woke up and saw that my pc rebooted on its own and I had a windows message. Mini Dump File is attached
031013-16421-01.dmp 3/10/2013 10:49:34 AM DRIVER_POWER_STATE_FAILURE 0x0000009f 00000000`00000003 fffffa80`1ae02060 fffff880`00a877e0 fffffa80`1f4fd4d0 ntoskrnl.exe ntoskrnl.exe+7b040 x64 ntoskrnl.exe+7b040 C:\Windows\MiniDump\031013-16421-01.dmp 8 15 9200 1,091,816
Sys Info
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 8 Pro, 64 bit
Processor: Intel(R) Core(TM) i7-3770K CPU @ 3.50GHz, Intel64 Family 6 Model 58 Stepping 9
Processor Count: 8
RAM: 32591 Mb
Graphics Card: NVIDIA GeForce GTX 660, -2048 Mb
Hard Drives: C: Total - 243845 MB, Free - 156766 MB; F: Total - 1907726 MB, Free - 1826013 MB; H: Total - 953866 MB, Free - 947904 MB;
Motherboard: Gigabyte Technology Co., Ltd., Z77X-UP4 TH
Antivirus: AVAST FREE
 

A:BSOD Power State Failure

Read other 11 answers
RELEVANCY SCORE 82

MSI S6000 running OEM windows 7 Home Premium 64 bit - 1.5 years
Intel I5
4GB Ram
Running IE 9

Any help greatly appreciated.

Mike

A:BSOD Power State Failure

Device Concerns:
Code:
Cisco AnyConnect VPN Virtual Miniport Adapter for Windows x64 ROOT\NET\0000 This device is disabled.
SBRE ROOT\LEGACY_SBRE\0000 This device is not present, is not working properly, or does not have all its drivers installed.
Cisco is disabled when it is not in use. Probably not a problem.
For SBRE: SBRE, is reporting "tv_ConfigMgrErr24". - Microsoft Answers
Analysis:You have remnants of Sunbelt/GFI VIPRE or adaware on the system. It may also be a program I am unfamiliar with... System Control Manager, perhaps?

Something is interfering with your wireless network. I suspect security software, and since MSE and Malwarebytes are known to not cause issues, we should look elsewhere. What other security software do you have installed besides those two and System Control Manager?

SuperAntiSpyware also is known to be stable, by the way...
3rd Party Drivers:The following is for informational purposes only:
Code:
intelppm.sys Mon Jul 13 17:19:25 2009 (4A5BC0FD)
HECIx64.sys Thu Sep 17 13:54:16 2009 (4AB293E8)
RTKVHD64.sys Wed Nov 25 03:08:12 2009 (4B0D020C)
ETD.sys Mon Jan 18 05:37:56 2010 (4B545624)
IntcDAud.sys Wed Feb 3 06:38:31 2010 (4B697C57)
Impcd.sys Fri Feb 26 16:32:11 2010 (4B8859FB)
iaStor.sys Wed Mar 3 19:51:31 2010 (4B8F2033)
amdxata.sys Fri Mar 19 10:18:18 2010 (4BA3A3CA)
SBFWIM.sys Tue Feb 8 04:37:58 2011 (4D512B16)
sbtis.sys Tue Apr 5 12:12:37 2011 (4D9B5B95)
SbFw.sys Tue Apr 5 12:12:59 2011 (4D9B5BAB)
Rt64win7.sys Fri Jun 10 00... Read more

Read other 3 answers
RELEVANCY SCORE 82

Details required:

OS : Windows 7 32 bit
Original OS: Windows XP
Full Retail Version
Age of Hardware: Motherboard & Processor - 3 years, Video Card - 1 year
Age of OS: less than a year; 6 months approx.

CPU: Intel Core2Duo E8400 3 GHz
Video Card: ATI Radeon HD 5670
Motherboard: Gigabyte P35-DS3R
Power Supply: not sure..

A:BSOD - Power State Failure

NOTE: I have severe eye problems. If I do not respond to your postings, please PM another staff member for assistance.

21 memory dumps from 14 Jul to 15 Oct 2011

MSINFO32 reports many STOP 0x9F errors dues to ewusbmdm.sys. This belongs to your "Huawei Mobile Connect" package from your Internet Service Provider fir the Huawei USB device that you're using. Please immediately install new Windows 7 compatible drivers (NOT Vista or XP drivers)

It also reports many STOP 0x116 and 0x117 errors blaming your ATI video card drivers. Please follow these steps to troubleshoot the video errors: http://www.sevenforums.com/crash-loc...eshooting.html

Samsung Kies is known to cause BSOD's on Win7 systems if using older drivers. Uninstall this program to see if it stops the BSOD's, then install freshly downloaded Win7 compatible drivers if you must use it.

BSOD BUGCHECK SUMMARY

Code:

Loading Dump File [C:\Users\FUBAR\_jcgriff2_\dbug\__Kernel__\101511-17175-01.dmp]
Built by: 7601.17640.x86fre.win7sp1_gdr.110622-1506
Debug session time: Fri Oct 14 16:07:18.854 2011 (UTC - 4:00)
System Uptime: 0 days 3:34:24.930
*** WARNING: Unable to verify timestamp for ewusbmdm.sys
*** ERROR: Module load completed but symbols could not be loaded for ewusbmdm.sys
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0x9F
PROCESS_NAME: SYSTEM
FAILURE_BUCKET_ID: 0x9F_3_ewusbmdm_IMAGE_usbccgp.sys
Bugcheck code 0000009F
Arguments 00000003 86a1da00 82d75ae0 85dc6760
BiosVersion = F9
B... Read more

Read other 1 answers
RELEVANCY SCORE 82

Hello,

Every since I had Telus Internet installed, my computer keeps giving me a BSOD when it goes to sleep. It's a Driver_Power_State_Failure ... 0x0000009F.

I don't get this with Shaw internet, only with Telus (I also have Optik TV on the same network). I still have both providers, and the computer is stable with shaw, but not with Telus.

I can eliminate the error by switching the Power Options so the hard drives "Never" turn off ... but I'm not sure what affect this has on the computer.

Please help, I don't understand mini-dumps and I've spent about 10 hrs on the phone.

My computer was orginally Vista, but my Hard drive crashed so I installed the full version of Windows 7 on the computer. Its 32 bit, on a 2-3 year old computer (Intel Core 2 Quad CPU Q9450).

I appreciate the help!

A:BSOD Power State Failure - Please help

Hi, Curtis. Sorry you are having problems. Your dumps are blaming e1e6232.sys, which is a LAN driver (network adapter) for the crashes. This driver is up to date and something else may be interfering with it.

Code:
Windows 7 Kernel Version 7600 MP (4 procs) Free x86 compatible
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16617.x86fre.win7_gdr.100618-1621
Machine Name:
Kernel base = 0x82c1b000 PsLoadedModuleList = 0x82d63810
Debug session time: Mon Nov 22 21:55:01.429 2010 (GMT-5)
System Uptime: 0 days 0:54:38.224
Loading Kernel Symbols
...............................................................
................................................................
.................................
Loading User Symbols
Loading unloaded module list
........
0: kd> !Analyze
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, 85e6db60, 82d41ae0, 85995328}

*** WARNING: Unable to verify timestamp for e1e6232.sys
*** ERROR: Module load completed but symbols could not be loaded for e1e6232.sys
Probably caused by : e1e6232.sys

Followup: Ma... Read more

Read other 9 answers
RELEVANCY SCORE 82

I have been receiving BSOD's when trying to shut down / restart my notebook since yesterday.

POWER STATE FAILURE

It gave me that error in the BSOD. I have tried updating my drivers ( graphic card drivers weren't signed ) but that didn't help.

I have included the minidump in this post.

Thank you.

A:BSOD - Power State Failure

Sorry, did not notice the Blue Screen of Death (BSOD) Posting Instructions.

Here are the files requested.
http://www.mediafire.com/?bs0vlt9krf4209m

(Could not attach file for some reason, disconnected halfway through uploading)

OS: Windows Vista Enterprise (32-bit)

Thank you.

Read other 1 answers
RELEVANCY SCORE 82

Can anyone tell me the problematic driver and how to remove it specifically? Thanks in advance I really appreciate those with debugging software.

-Alan

PS I can't seem to run the SF Diagnostic Tool in Administrative mode. it says "Windows cannot access the specified device, path, or file. You may not have the appropriate permission to access the item."

A:BSOD power state failure

There's not a whole bunch of information in the dump file (that's why we need the SF Diagnostic Tool files). Without that we'll need, at a minimum, your COMPLETE complete system specs and the report from running MSINFO32.exe.

The error blames hardware - so it can be either a problem with your hardware or with a driver.
The driver involved probably is nvhda64v.sys - a component of your nVidia HDMI audio drivers

You also have other nVidia drivers that are older - so I'd suggest updating your nVidia chipset and video drivers directly from the nVidia website: Drivers - Download NVIDIA Drivers
Here's the older drivers:

Code:
nvmfdx64.sys Sat Nov 17 18:47:57 2007 - NVIDIA nForce Networking Controller Driver - http://www.carrona.org/dvrref.html#nvmfdx64.sys
nvsmu.sys Fri Oct 12 19:53:40 2007 - NVIDIA nForce System Management Controller (nVidia nForce chipset driver) - http://www.carrona.org/dvrref.html#nvsmu.sys
Summary of the BSOD:

Code:
Built by: 7600.16385.amd64fre.win7_rtm.090713-1255
Debug session time: Fri Apr 16 09:33:42.633 2010 (GMT-4)
System Uptime: 0 days 10:42:31.849
BugCheck FC, {fffff8000304c0f0, 800000000304c963, fffff88002fb9540, 2}
*** WARNING: Unable to verify timestamp for nvhda64v.sys
*** ERROR: Module load completed but symbols could not be loaded for nvhda64v.sys
Probably caused by : hardware ( nvhda64v+cae8 )
BUGCHECK_STR: 0xFC
PROCESS_NAME: System

Read other 3 answers
RELEVANCY SCORE 82

Woke up one day a couple weeks ago to find my laptop's onboard fan screaming. I opened the laptop to find a lovely BSOD awaiting me. All I caught before I killed the power to the machine was the term "power state failure". I'm not sure what happened, and I'm not too concerned about it now, but I'd very much like to know exactly what happened.

DETAILS:

Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7601.2.1.0.768.3
Locale ID: 1033

Additional information about the problem:
BCCode: 1000009f
BCP1: 0000000000000004
BCP2: 0000000000000258
BCP3: FFFFFA80073AD040
BCP4: FFFFF80000B9C3D0
OS Version: 6_1_7601
Service Pack: 1_0
Product: 768_1



MINIDUMP FILE:
bsod_details_1.zip

A:BSOD power state failure

Hi,

The dump you've attached mentions memory corruption (most likely driver related until shown otherwise), although it also mentions nusb3hub.sys (NEC Electronics USB 3.0 Host Controller Driver). It's well known to cause BSODs. You can remove it yourself, or you can update it here. Choice is yours.


Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 1000009F, {4, 258, fffffa80073ad040, fffff80000b9c3d0}

Unable to load image \SystemRoot\system32\DRIVERS\nusb3hub.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nusb3hub.sys
*** ERROR: Module load completed but symbols could not be loaded for nusb3hub.sys
*** WARNING: Unable to verify timestamp for win32k.sys
*** ERROR: Module load completed but symbols could not be loaded for win32k.sys
Probably caused by : memory_corruption

Followup: memory_corruption
---------

0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis ... Read more

Read other 3 answers