Over 1 million tech questions and answers.

Getting BSOD - Driver Power State Failure when going into sleep mode

Q: Getting BSOD - Driver Power State Failure when going into sleep mode

I have tried to test this issue my self by trying to read trough the DMP file and Event Viewer. (haven't done this before, so i think i have possibly overlooked something)
The computer model is: HP ProBook 430 G2
The things i have tried is uninstalling and updating the drivers.
Using another OS Disk (It worked fine when doing this)
Starting in safe mode (This also worked fine)
Checked advanced power settings (Was nothing wrong there from what i could see)

Read other answers
RELEVANCY SCORE 200
Preferred Solution: Getting BSOD - Driver Power State Failure when going into sleep mode

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

RELEVANCY SCORE 136.4

Hello, all. Every now and again my laptop BSOD's when I leave it on sleep mode over night. Today the laptop lit up and started running while it was closed and I opened it to see the Driver_State_Power_Failure error message. Attached are the files gained from the SF Diagnostics Tool. Any help is greatly appreciated.

A:BSOD During Sleep Mode - Driver State Power Failure

Hello fran.

It appears that Avast is causing the BSODs there.

avast! Self Protection Driver

Code:
fffff880`02677de8 fffff880`068e2940Unable to load image \SystemRoot\System32\Drivers\aswSP.SYS, Win32 error 0n2
*** WARNING: Unable to verify timestamp for aswSP.SYS
*** ERROR: Module load completed but symbols could not be loaded for aswSP.SYS
aswSP+0x2f940
Description here: Driver Reference Table - aswSP.SYS

avast! Virtualization Driver

Code:
fffff880`02677d68 fffff880`066d32ccUnable to load image \SystemRoot\System32\Drivers\aswSnx.SYS, Win32 error 0n2
*** WARNING: Unable to verify timestamp for aswSnx.SYS
*** ERROR: Module load completed but symbols could not be loaded for aswSnx.SYS
aswSnx+0x4e2cc
Description here: Driver Reference Table - aswSnx.SYS

Uninstall Avast using Avast Uninstall Utility. Use Microsoft Security Essentials as your antivirus with windows inbuilt firewall, and free MBAM as the on demand scanner.
Download, install and update those, and then run full system scans with both of them, one by one.

Using more than one antivirus program is not a good practice. It will make your system unstable in turn. Uninstall McAfee Using McAfee Removal Tool.

Daemon Tools, Alcohol 120% and Power Archiver Pro uses SCSI Pass Through Direct (SPTD), which is a well known BSOD causer. Uninstall Daemon Tools at first. Then download SPTD standalone installer from Disk-Tools.com, and execute the downloaded file as guided below :
Double click to open it... Read more

Read other 1 answers
RELEVANCY SCORE 136.4

Hey!

I got an BSOD from sleep mode. Was off to go outside the summer heat today and when I came back... BSOD..


However the system managed to dump two files for me on BSOD.

Take a look and thanks for the help you give me :)

A:DRIVER POWER STATE FAILURE Sleep mode BSOD.

Hello,

Please take a look at the following thread and perform all of the requested steps.

Once you have all the requested reports please attach back here.

http://www.techsupportforum.com/foru...ta-452654.html

One dump is really not sufficient to determine the cause. The reports will also provide other info to help diagnose the issue.

The dump provided indicates a problem with the Realtek Network driver please try updating or re-installing this driver.

Realtek

I would also suggest that you fully update Windows including the Windows 7 Service Pack.


Code:
Windows 7 Kernel Version 7600 MP (4 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16617.amd64fre.win7_gdr.100618-1621
Machine Name:
Kernel base = 0xfffff800`03268000 PsLoadedModuleList = 0xfffff800`034a5e50
Debug session time: Fri May 10 12:00:54.715 2013 (UTC - 4:00)
System Uptime: 0 days 8:41:33.010
Loading Kernel Symbols
...............................................................
................................................................
...........................
Loading User Symbols
Loading unloaded module list
......
*******************************************************************************
* *
* Bugcheck Analysis *
* *... Read more

Read other 2 answers
RELEVANCY SCORE 134.8

I'm using a Lenovo Y50 running Windows 8.1. This issue has been happening every now and then for the past week or so. I noticed it occurs briefly after waking the computer from sleep mode. I can get to the desktop but about a minute after waking, the laptop will freeze up and give me a blue screen saying it was a DRIVER_POWER_STATE_FAILURE. I'm assuming this error has to do with some driver, but I don't know how to figure out which driver is the one causing the issue. I looked in Device Manager and can't find any yellow exclamation marks pointing out issues.

Here's a link to the most recent dmp file:
https://drive.google.com/file/d/0B2kQd8xpvK9STnd3MjVFWHJJOEE/view?usp=sharing

Thank you in advance to anyone who can help me out with this!
 

A:BSoD - Driver Power State Failure after waking from sleep mode.

For the time being and for troubleshooting, please uninstall Trend Micro and just
utilize Windows Defender. Trend Micro can be reinstalled once the problem is isolated.
http://esupport.trendmicro.com/en-us/home/pages/technical-support/1105809.aspx

What is all plugged in via USB?
Did this started happening after installing/updating Razor Synapse?
 

Read other 1 answers
RELEVANCY SCORE 134.8

Hello

I am experiencing a BSOD (DRIVER POWER STATE FAILURE) error with my ACER notebook.
It always come up after I put the computer in sleep mode.

After dozen of search and websites, I found this forum.

I hope you will be able to help me.

Please find below the informations about my OS
- Windows 7 Home Premium Edition
- x64
- OEM
- age of the system : 3 years old. The hard drive has been replaced 1 year ago.
- age of OS installation : 2 days old (reinstalled from the recovery disk)

I have also attached the System Health Report AND the BSOD Dump & System File Collection report.

Let me know if you need something else... and Thank already !

A:BSOD after sleep mode, 0x0000009f (DRIVER POWER STATE FAILURE)

Please install any Windows Updates you have not yet installed. I notice you do not have Service Pack 1 installed yet.Update to Service Pack 1 (SP1)Download Details - Microsoft Download Center - System Update Readiness Tool for Windows 7 (KB947821) [August 2011]

Download Details - Microsoft Download Center - System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [August 2011]

Steps to follow before you install Windows 7 Service Pack 1 from the Microsoft Download Center

Service Pack 1 Download site




Crashes indicate USB device issues.Start with USB Driver - General Fix for Problems to resolve the USB issues. Also, USB ports can sometimes enter a safe power state to protect the system from power surges due to USB devices. To reset the USB ports to a nominal power state:
Shut down and turn off the computer.
Unplug the computer from the wall or surge protector (then remove the battery if it is a laptop).
"Remove the computer from any port replicator or docking station, disconnect
cables to printers or devices such as external monitors, USB memory sticks or SD cards, headset or external speakers, mouse or auxiliary keyboard, turn off WIFI and Bluetooth wireless devices." (Use Hard Reset to Resolve Hardware and Software Issues HP Pavilion dv5000 Notebook PC series - HP Customer Care (United States - English))
Hold down the power button for 30 seconds. This closes the circuit and ensures all
power from components is drained t... Read more

Read other 1 answers
RELEVANCY SCORE 133.6

Hello all

This is my first post in here. Please bear over with my English – it is not my native language.

My problem is on a Media Centre machine where I recently upgraded Motherboard and processor. I have the following setup on the machine:
SILVERSTONE Grandia 04
DeZen PSU 500 Watt, TitanPower, 17-19 db
MB: Asus P8H77-MLE
CPU: Intel i3 2120
2x4 GB Corsair Vengeance ram (just bought new ones to see if it would help)
OCZ Agility 3 SSD 120 GB
1,5 TB WD Caviar Green
Asus P7131 Tuner
TERRATEC Cinergy DT USB XS Diversity
Hauppauge! WinTV-NOVA-T-Stick-Diversity
Hauppauge! Smart CI USB

My previous setup was with a AMD 240e but I have made a clean install.

I use Microsoft Security Essentials for antivirus and have firewall turned on.

The Media Centre machine is on for 24/7 on sleep mode for recordings or turned on for showing recordings.
Since the upgrade I have BSOD most times after it is turned on after sleep. The STOP occurs 4-5 minutes after the wake up either the wakeup is initiated from a recording or from user. I even see BSOD occur in the middle of the night where I have no recordings or other activity.

I have made several new install and tried to exclude the SSD and install a 32 bit Win7 – but the BSOD still occurs 4-5 min after awake.

I have updated all drivers and tried to run Verifier with no luck.

Hopefully someone can help

A:BSOD after sleep mode, error DRIVER POWER STATE FAILURE 0x0000009f

I have updated the Perfmon details - I had forgot to run the Windows Experience Index

Read other 9 answers
RELEVANCY SCORE 124.4

I am experiencing an issue with my laptop where I can't allow it to enter sleep mode or else it will restart/appear to have restarted the next time I wake it up. At first I thought it might be a power options issue, but I made sure that the computer was set to sleep and not restart when I close the lid. I've checked the bluescreen viewer and the cause of the restart seems to come from a driver power state failure coming from ntoskrnl.exe+1fcc1e, hal.dll+6a37, and storport.sys+33f0.

I've already run sfc/scannow to check for damaged files and I was also able to replace them using a DISM command, so now scanning the computer doesn't run into any errors, but this driver error still persists.

Sidenote: The driver errors mainly started after I reinstalled Kaspersky onto my computer to fix some issues that I had with it. Before that I was getting a couple of kernel data inpage errors, the latest of which occurred June 1.

A:Driver Power State Failure in sleep mode

Hi M15 and welcome to the forums ^_^,

I am in the process of analyzing your dump files further. Below has been provided analysis of your dump files for Informative purposes.

Code:
**************************Fri Jun 6 04:50:12.040 2014 (UTC + 5:30)**************************Probably caused by : storport.sys ( storport!RaSendIrpSynchronous+70 )

BugCheck 9F, {4, 12c, ffffe0017919e880, ffffd00049969950}
BugCheck Info: DRIVER_POWER_STATE_FAILURE (9f)

BUGCHECK_STR: 0x9F

DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT

PROCESS_NAME: System

FAILURE_BUCKET_ID: 0x9F_4_storport!RaSendIrpSynchronous

MaxSpeed: 1800

CurrentSpeed: 1796

BIOS Version V2.20

BIOS Release Date 02/18/2013

Manufacturer Acer

Product Name Aspire M5-481PT

??????????????????????????????????????????????????????????????????????????????????????``
**************************Fri Jun 6 01:42:48.219 2014 (UTC + 5:30)**************************
*** WARNING: Unable to verify timestamp for iaStorA.sys

*** ERROR: Module load completed but symbols could not be loaded for iaStorA.sys

Probably caused by : iaStorA.sys

BugCheck 9F, {3, ffffe000d7f8e060, ffffd000ca5e9930, ffffe000da3955c0}
BugCheck Info: DRIVER_POWER_STATE_FAILURE (9f)

BUGCHECK_STR: 0x9F

DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT

PROCESS_NAME: System

FAILURE_BUCKET_ID: 0x9F_3_POWER_DOWN_disk_IMAGE_iaStorA.sys

MaxSpeed: 1800

CurrentSpeed: 1796

BIOS Ver... Read more

Read other 12 answers
RELEVANCY SCORE 124

Hi, i keep having this issue. Anyone knows how to solve?
My minidump is https://skydrive.live.com/#cid=392FCBBA17F5ACA1&id=392FCBBA17F5ACA1%21187

A:BSOD when going sleep mode "DRIVER POWER STATE FAILURE"

Related to Rt64win7.sys 8101E/8168/8169 NDIS 6.20 64-bit Driver from Realtek Corporation.

I would re-install newest driver available.

Read other 1 answers
RELEVANCY SCORE 122.8

I'm having a BSOD problem. After walking computer from sleep mode, within 1-2 minutes it will get a BSOD with the "driver power state failure" error and restart, but interestingly I never get the error the moment I wake up the computer. I'm using a Lenovo IdeaPad Y510P with Windows 8.1 64-bit. I already tried uninstalling the Intel HD 4000 driver, restarting computer, and installing the one on Lenovo's site (as this was suggested on the Lenovo forum as a common fix) but it didn't help. The problem only started occurring after one of the following:
- Updating Malwarebytes to latest last week
- Installing a Windows update last week (there were 3 installed components, 1 of them was an Intel HD 4000 driver update, forgot what the other 2 were)
- Updating GeForce Experience and latest NVIDIA Graphics Driver (337.88), it included NVIDIA PhysX System Software 9.13.1220
Here is a log created by WinDbg tool: 'BSOD dump' | TextUploader.com
Here is a log created by BluescreenView:
==================================================
Dump File : 060514-96281-01.dmp
Crash Time : 6/5/2014 7:23:39 PM
Bug Check String : DRIVER_POWER_STATE_FAILURE
Bug Check Code : 0x0000009f
Parameter 1 : 00000000`00000003
Parameter 2 : ffffe001`218f88e0
Parameter 3 : ffffd000`bff2b930
Parameter 4 : ffffe001`2561d1c0
Caused By Driver : ntoskrnl.exe
Caused By Address : ntoskrnl.exe+153fa0
File Description :
Product Name :
Company :
File Version :
Processor : x64
Crash Address : ntoskrnl.exe+153f... Read more

A:Driver power state failure after resuming from sleep mode

Hi Lan1 and welcome to the forums ^_^,

I have analyzed your Dump file and below has been provided an analysis of your dump file for informative purposes :-

Code:
2: kd> !analyze -v*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
DRIVER_POWER_STATE_FAILURE (9f)
A driver has failed to complete a power IRP within a specific time.
Arguments:
Arg1: 0000000000000003, A device object has been blocking an Irp for too long a time
Arg2: ffffe00135b5c060, Physical Device Object of the stack
Arg3: ffffd000c3df9930, nt!TRIAGE_9F_POWER on Win7 and higher, otherwise the Functional Device Object of the stack
Arg4: ffffe0013217d880, The blocked IRP
Debugging Details:
------------------


DRVPOWERSTATE_SUBCODE: 3
DRIVER_OBJECT: ffffe00135b70c30
IMAGE_NAME: usbccgp.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 52678625
MODULE_NAME: usbccgp
FAULTING_MODULE: fffff80157d82000 usbccgp
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
CURRENT_IRQL: 2
ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre
STACK_TEXT:
ffffd000`c3df98f8 fffff801`31803c1e : 00... Read more

Read other 7 answers
RELEVANCY SCORE 122.8

I am using lenovo G580-20150.
I know this problem have been opened a tread but the problem i dont' think it's same so i woud like to ask for some solution after listening to my problem.
I have been user of windows 8 and 8.1 for quite some time.
everything works fine for me for the windows that i currently using , windows 8.1.
including i can put in sleep and wake it as usual.
but ! since past few days i notice that my computer getting weird when i enter sleep mode (for example closing the lid)
it crash... it bsod.

And it occur since the day after i installed somekind of VPN software and wiFI sharing that my friend gave me.
After that day, i can't put my computer into sleep. whenever i do that it keep crash.

at first , i thought lenovo energy management that cause the prob
so i uninstalled... it still makes no different , still i can't put my computer to sleep.
after that i uninstalled the vpn and wifi sharing software, it still makes no different.
But i am very sure that the vpn and wifi sharing software cause the problem.

Because before this everything works fine until that two software comes to my computer. I really need someone that able to analysis the dmp file. TQ

I willing to learn and contribute if i were given the opportunity . tq

A:Driver Power State Failure after enter sleep mode

Hi Eric & Welcome to the forums ^_^,

I have analysed your dump files and below has been provided an analysis of the same for informative purposes :-

Code:
0: kd> !irp ffffe00175b29e10
Irp is active with 3 stacks 2 is current (= 0xffffe00175b29f28)
No Mdl: No System Buffer: Thread 00000000: Irp stack trace.
cmd flg cl Device File Completion-Context
[ 0, 0] 0 0 00000000 00000000 00000000-00000000
Args: 00000000 00000000 00000000 00000000
>[ 16, 2] 0 e1 ffffe00177cc0050 00000000 fffff8025f7952d8-ffffe00173c59d60 Success Error Cancel pending
\Driver\tunnel nt!PopRequestCompletion
Args: 00015600 00000001 00000004 00000003
[ 0, 0] 0 0 00000000 00000000 00000000-ffffe00173c59d60
Args: 00000000 00000000 00000000 00000000


Now, as we can see from the Dump file analysis, "tunnel.sys" has been blamed which is the Microsoft's Tunneling Driver but since it is a component of Windows, chance of it being the culprit is extremely low. This means your guess that the BSOD are caused by the VPN Software.

On checking the Drivers, I found the SoftEther VPN installed on your system. Please uninstall it from the system and see if the system still BSOD's or not.

Let me know how it goes ^_^.

Read other 3 answers
RELEVANCY SCORE 119.2

When I go to open my laptop back up everything comes on but the home screen won't come on. The fans run, LED backlight and keyboard comes on. I have to turn the laptop off by holding the power button then it all comes up. EDIT: I have went through the Lenovo Service Bridge and checked for updates and the only thing that wasn't updated was the solutions center so it looks like everything is up to date.Also I threw in the driver power state failure so I didn't have to open another thread. That has been going on for some time while I'm doing things and I'm not sure what to do. 

Read other answers
RELEVANCY SCORE 119.2

When I go to open my laptop back up everything comes on but the home screen won't come on. The fans run, LED backlight and keyboard comes on. I have to turn the laptop off by holding the power button then it all comes up. EDIT: I have went through the Lenovo Service Bridge and checked for updates and the only thing that wasn't updated was the solutions center so it looks like everything is up to date.Also I threw in the driver power state failure so I didn't have to open another thread. That has been going on for some time while I'm doing things and I'm not sure what to do. 

Read other answers
RELEVANCY SCORE 118.8

I've started getting driver power state failures BSODs after my computer goes to sleep.

These started in the last couple of weeks. It's happened twice today already. When I first noticed these occurring, I used System Restore to undo my last installs, but it didn't help.

I'd greatly appreciate any help fixing this.

A:BSOD after going to sleep, driver power state failure

Welcome

Your Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC is causing BSoD
Update to latest drivers

Code:
>[ 16, 2] 0 e1 fffffa8005c3a050 00000000 fffff800032d5200-fffffa8007049c50 Success Error Cancel pending
Unable to load image \SystemRoot\system32\DRIVERS\Rt64win7.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for Rt64win7.sys
*** ERROR: Module load completed but symbols could not be loaded for Rt64win7.sys
\Driver\RTL8167 nt!PopSystemIrpCompletion
Args: 00014400 00000000 00000004 00000002
[ 0, 0] 0 0 00000000 00000000 00000000-fffffa8007049c50

Args: 00000000 00000000 00000000 00000000
0: kd> lmvm Rt64win7
start end module name
fffff880`06d15000 fffff880`06d7f000 Rt64win7 T (no symbols)
Loaded symbol image file: Rt64win7.sys
Image path: \SystemRoot\system32\DRIVERS\Rt64win7.sys
Image name: Rt64win7.sys
Timestamp: Wed Jan 26 19:34:03 2011 (4D4022CB)
CheckSum: 0006AFBB
ImageSize: 0006A000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
Source | Driver Reference Table

Also Take memtest. Run for 8 passes and test each stick in a know good slot for an additional 6 passes.

→ RAM - Test with Memtest86+
→ Guide to using Memtest86+ - Geeks to Go Forums

Read other 9 answers
RELEVANCY SCORE 118.8

Been having issues with sleep mode with my build for months but in the past couple weeks it has gotten worse. When the computer goes into sleep, there's about a 50 percent chance it will wake up when I move the mouse. The other times I have to hard restart. In the past week it is now BSODing and giving me the attached dump reports. I'm pretty sure it's a driver issue but I can't narrow it down any more than that. Interested to hear what the experts think.

A:BSOD DRIVER STATE POWER FAILURE 9f, on sleep

Hi slash196.

Update the driver to TP-LINK 150Mbps Wireless Lite N Adapter from Download - Welcome to TP-LINK, by matching with your device number.

Install Service pack 1 and all other windows updates. Otherwise the system will remain vulnerable to threats.

Code:
OS Name Microsoft Windows 7 Ultimate
Version 6.1.7600 Build 7600
Learn how to install Windows 7 Service Pack 1 (SP1)
Service Pack and Update Center - Microsoft Windows

Also, if possible, update the BIOS to Version 1501 from ASUSTeK Computer Inc. -Support- Drivers and Download M4A88TD-M/USB3

Let us know the results.

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa8006a9e060, fffff80000b9c518, fffffa800a2fb920}

Probably caused by : ntkrnlmp

Followup: MachineOwner
------------------------------------------------------------------------------------------
Dispatch routines:
[00] IRP_MJ_CREATE fffff880016e7c30 ndis!ndisCreateIrpHandler
[01] IRP_MJ_CREATE_NAMED_PIPE fffff8800177e490 ndis!ndisDummyIrp... Read more

Read other 1 answers
RELEVANCY SCORE 117.6

Dear Sir/Madam,

I've been having this issue since updating to Windows 8.1. I will wake my computer from it's sleep and a few minutes later I get the BSOD. In one notable event early on, I got two in a row after the computer restarted from the previous BSOD.

I fiddled with my power settings (I was trying to avoid my computer actually shutting down during sleep/hibernation) a few months ago and after that I didn't have any BSOD events that I recall until this past week. When they do happen, they tend to happen in rapid succession, as you can see from the dates on the collected data I've attached (I see there's a .txt file with all my computer's information for you reference) - I've had one every day for the past three days.

I've read through many of these threads and tried several of the solutions. I am running verifier.exe since the BSOD has started up again since from what I can understand from reading the .dmp file and this forum that the message I'm getting about ntoskrnl.exe is misleading (?).

Please take a look at the dumps and other information collected from the DM Log Collector Tool and let me know if you can help me solve this problem.

Thank You.

A:BSOD Waking from Sleep (power state driver failure)

Hi, pnutbudder,

I've been having a similar problem since a few weeks ago. I suspect this is due to a recent Windows or driver update, since both of us had the same problem at the same time. I'm going to take a look at your dump files in a few hours, but in the meantime, could you tell me

1. whether you have Evernote or any Blizzard games installed
2. whether you've installed any new programs recently,
3. what graphics drivers you have installed,
4 what music or audio programs you have installed (eg, music players, movie editors, music studios and recording programs, game streaming programs)?

EDIT: Okay, I took a look at your dump files, and they point to a bad interaction between the "usbccgp.sys" and the "ksthunk.sys" driver. These are the same drivers that are misbehaving on my system, too (Lenovo Y510P). As far as I can tell, the only device that uses ksthunk.sys is the Lenovo EasyCam. Try this fix:

1. Download the "Broadwell" version of the camera driver on this page: http://support.lenovo.com/us/en/prod...loads/DS101169 . We're going to replace your current camera driver with Lenovo's original camera driver.
2. Open "Device Manager" by right-clicking on the lower left corner of the screen.
3. Double-click "Imaging Devices" to open it.
4. Right-click "Lenovo EasyCamera" and click "Disable". You should see a small downward-pointing arrow appear next to the picture.
5. Right-click "Lenovo EasyCam... Read more

Read other 5 answers
RELEVANCY SCORE 117.6

Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7600.2.0.0.768.3
Locale ID: 1033

Additional information about the problem:
BCCode: 9f
BCP1: 0000000000000003
BCP2: FFFFFA8009DBD060
BCP3: FFFFF80000B9C518
BCP4: FFFFFA800ED33010
OS Version: 6_1_7600
Service Pack: 0_0
Product: 768_1

Files that help describe the problem:
C:\Windows\Minidump\120410-48828-01.dmp
C:\Users\Jon\AppData\Local\Temp\WER-70980-0.sysdata.xml

Read our privacy statement online:
http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409

If the online privacy statement is not available, please read our privacy statement offline:
C:\Windows\system32\en-US\erofflps.txt
Yeah, i get this whenever my computer goes idle and into sleep mode, and when i shut down. Any way to fix???

minidump -- http://www.megaupload.com/?d=J07IWJQ0
 

Read other answers
RELEVANCY SCORE 117.6

New build i7 asrock motherboard W8 Pro. when waking from sleep everytime I get driver_power_state_failure BSOD.
Looking for some help on where to start. Updated the bios and everything else works great.

Thanks for any advice

Attachment 14584

A:BSOD Driver Power State Failure when waking from sleep

You have 3 hard drives - what is the make/model/wattage and age of your Power Supply?

We've seen a number of BSOD issues with SSD's. Here's the information that I've compiled so far:





There's not a whole bunch available to test SSD's. The "easiest" test is to remove the SSD, install a platter-based hard drive, install Windows and test for stability that way.

Here's some suggestions:
- Update the SSD's firmware to the latest available version (VERY IMPORTANT!!!)
- Update the motherboard controllers drivers to the latest available version from the controller manufacturer (NOT the mobo manufacturer unless you can't find any on the controller manufacturer's website)
- Slow the memory (RAM) down to the next slower speed (I've only seen one person who claimed that this worked for them).
- Use any manufacturer's utilities that you may have. If you don't have any, then try this free one (I haven't used it myself): Crystal Dew World
- Update chipset and storage controller drivers to the latest available from the manufacturer of the device (not the manufacturer of the motherboard). Be sure to update ALL controllers on the motherboard!
....NOTE: Recently (Nov 2011) we had BSOD issues with the Marvell 91xx controller and an SSD. You may have to switch controllers also.
- Replace the SSD with a platter based hard drive and see if that stops the BSOD's. If it does, then it's likely that there's a problem with the SSD OR an incompatibility with you... Read more

Read other 5 answers
RELEVANCY SCORE 116.4

I am getting a BSOD mostly when I turn the computer on from sleep mode during sleep wifi will be on and most probably 1 of the browsers would have been working.

Reinstalled Windows 7 on Oct 8 and downloaded some drivers from the net.

I have uploaded the SF diagnostic zip file

Any help would be greatly appreciated

A:BSOD after turning computer on from sleep DRIVER POWER STATE FAILURE

Welcome aboard. Is there any reason that you haven't installed service pack 1?

Read other 9 answers
RELEVANCY SCORE 115.2

i guess i've been having this problem for about a month or so now and it's really becoming frustrating because everytime i have to leave my computer i have to shut it down if i don't want a BSOD..

i hope that someone can help me... every time i try to hibernate my laptop which is a HP DV4 Windows 7 Laptop i get a blue screen of death. it only started happening recently....maybe after i installed bit-defender..i'm not really sure..but it was doing fine before bit defender......

i used blue-screen view and with each time it registers a error it's with the driver for the NTOSKRNL.exe... i really hope that someone could help me because i just want my computer to go back to normal....and i wish that the problem has nothing to do with bit-defender......

tell me what you need and i'll try my best to get it to you so you can assist me with this problem cause i'm kinda new to the whole forum thing....

thanks..

A:[SOLVED] BSOD Driver Power State Failure When Hibernating/Sleep Windows 7 HP DV4

Hi and welcome to TSF please follow the instructions here http://www.techsupportforum.com/f217...ns-452654.html

Read other 17 answers
RELEVANCY SCORE 107.2

Hello,

I left my computer on and open this morning before I left for class. When I returned, I had a BSOD, which specified "Driver Power State Failure" (I did not copy down any numbers, as I probably should have). I did a forced shut down (held the power button) and then restarted it, where it fortunately works for now.

My laptop is an Dell XPS-15, about two years old. I have not had any problems with it until now, and the past week or so it has been freezing up. I downloaded the SF Diagnostic Tool, and the zipped folder is attached.

I am uncertain what action to take next. Could someone advise me in how to fix the issue?

Thank you!!

A:BSOD after sleep or hibernation - "Driver Power State Failure"

upload your MSINFO32.nfo file.
Click on the start button
Type "msinfo32" (without quotes) in the search bar of the start menu, click the resulting link. It will open the System Information window.
File>Save. In the "File Name" filed, put "MSINFO32" (without Quote), give the save location to desktop, and click the "save" button.
Give the time for processing, it will save a .nfo file on your desktop.
Zip it, and upload it following the instruction.

Read other 3 answers
RELEVANCY SCORE 107.2

I have been using my asus laptop but recently started blue screening. When trying to shut it down the screen will go black, but the system lights remain on and it remains running, however irresponsive. It also began showing a blue screen with the warning "Driver power state failure".

Even after a factory reset this problem remains. Any help to figure out the problem would be greatly appreciated.

A:BSOD "driver power state failure", when shut down or sleep

Hi Chalcogen & Welcome to the forums ^_^,

I have analyzed your only dump file and a summary of that is given below :-

Code:
**************************Mon Jul 21 15:05:53.798 2014 (UTC + 5:30)**************************
*** WARNING: Unable to verify timestamp for win32k.sys

*** ERROR: Module load completed but symbols could not be loaded for win32k.sys

Probably caused by : memory_corruption

BugCheck 9F, {4, 12c, fffffa800aeacb00, fffff88001e9e800}
BugCheck Info: DRIVER_POWER_STATE_FAILURE (9f)

BUGCHECK_STR: 0x9F

DEFAULT_BUCKET_ID: CODE_CORRUPTION

FAILURE_BUCKET_ID: MEMORY_CORRUPTION_LARGE

MaxSpeed: 1900

CurrentSpeed: 2395


Processor may be overclocked!
Expected Frequency: 1900
Actual Frequency: 2395
Overclock Ratio: 1.26053

BIOS Version S550CM.202

BIOS Release Date 11/23/2012

Manufacturer ASUSTeK COMPUTER INC.

Product Name S550CM

??????????????????????????????????????????????????????????????????????????????????????``


Now, since the dump file blames the "Win32k.sys" which is a Windows Component, chance of it being at fault it extremely low. Below is a list of 3rd party drivers found over your system :-

Code:
**************************Mon Jul 21 15:05:53.798 2014 (UTC + 5:30)**************************
ASMMAP64.sys Thu Jul 2 14:43:26 2009 (4A4C7A36)
atkwmiacpi64.sys Wed Sep 7 07:14:52 2011 (4E66CC94)
AiCharg... Read more

Read other 3 answers
RELEVANCY SCORE 105.2

Hi,
I've been getting persistent BSOD's when attempting to wake up my computer (Lenovo Twist u230) from sleep. I am also sporadically getting Kernal Data Inpage Error BSOD while using my computer.

My machine is Windows 8, installed from factory with a recent refresh done. SFC /SCANNOW and DISM both come up clean. All of my hardware diagnostics are also clean.

Help!

A:Driver Power State Failure on wake from sleep

Which hardware diagnostics have you done?

Please run Driver Verifier according to these instructions: Driver Verifier Settings

Just a guess at this point, but try removing Diskeeper to see if that helps.
If not that, then try removing the Citrix software to see if it helps.

Analysis:
The following is for informational purposes only.

Code:
**************************Fri Oct 11 09:56:37.534 2013 (UTC - 4:00)**************************
Loading Dump File [C:\Users\John\SysnativeBSODApps\101113-15578-01.dmp]
Windows 8 Kernel Version 9200 MP (4 procs) Free x64
Built by: 9200.16628.amd64fre.win8_gdr.130531-1504
System Uptime:0 days 20:21:57.335
Probably caused by :Unknown_Image ( ANALYSIS_INCONCLUSIVE )
BugCheck 9F, {3, fffffa80036b7890, fffff800c68d07f0, fffffa800de92610}
BugCheck Info: DRIVER_POWER_STATE_FAILURE (9f)
Arguments:
Arg1: 0000000000000003, A device object has been blocking an Irp for too long a time
Arg2: fffffa80036b7890, Physical Device Object of the stack
Arg3: fffff800c68d07f0, nt!TRIAGE_9F_POWER on Win7, otherwise the Functional Device Object of the stack
Arg4: fffffa800de92610, The blocked IRP
BUGCHECK_STR: 0x9F
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
PROCESS_NAME: System
FAILURE_BUCKET_ID: 0x9F_3_ACPI_ANALYSIS_INCONCLUSIVE
CPUID: "Intel(R) Core(TM) i5-3317U CPU @ 1.70GHz"
MaxSpeed: 1700
CurrentSpeed: 1696
BIOS Version GDETA1WW (1.61 )
BIOS Release Date 09/14/2013
Manufacturer LENOVO... Read more

Read other 1 answers
RELEVANCY SCORE 105.2

My Toshiba laptop gives the above BSOD screen 9 out of 10 times when going to sleep. I have installed the latest Win 8 video drivers but that was no help.

I have attached a couple of the minidump files.

A:Driver, power, state, failure when laptop goes to sleep.

Hi,

Bit of a messy machine there. First thing is first. Update or uninstall your sptd.sys. The installer/uninstaller does either:

DuplexSecure - Downloads

----------

Update Synaptics Touchpad driver:


Code:
SynTP SynTP.sys Mon Aug 17 14:35:16 2009


----------

Update J-Micron Storage driver:


Code:
jmcr jmcr.sys Mon Jul 20 07:39:02 2009


JMicron/Home

-----------

Update from the manufacturer:


Code:
tosrfec tosrfec.sys Mon Jun 01 02:58:53 2009
tosrfcom tosrfcom.sys Tue Jul 28 06:18:20 2009
tosporte tosporte.sys Tue Jun 16 06:48:47 2009
Thpevm Thpevm.SYS Mon Jun 29 04:15:37 2009
thpdrv thpdrv.sys Sun Jun 28 22:02:56 2009


----------

Uninstall ESET. Windows 8 already has excellent a/v protection as a service.


Code:
epfw epfw.sys Tue Jun 28 03:30:10 2011
eamonm eamonm.sys Tue Aug 02 05:33:29 2011


----------

Uninstall ancient Acronis:


Code:
tifsfilt tifsfilt.sys Wed Aug 29 08:37:29 2007
timntr timntr.sys Wed Aug 29 08:38:23 2007


-----------

Update from manufacturer:


Code:
pgeffect pgeffect.sys Mon Jun 22 05:00:11 2009


---------

Visit Intel to let it scan to update storage drivers:


Code:
iaStor iaStor.sys Thu Jun 04 21:53:40 2009


---------

Update Realtek HD Audio:


Code:
RTKVHD64 RTKVHD64.sys Tue Jul 28 09:00:05 2009


Realtek

-------
Others needing update:


Code:
tdcmdpst tdcmdpst.sys Thu Jul 30 04:39:35 2009
TVALZ_O TVALZ_O.SYS Mon Jul ... Read more

Read other 3 answers
RELEVANCY SCORE 104

Laptop Sony Vaio Model VPCCW1Z4E
OS Windows 7 Home Premium Service pack 1
Processor Intel Core DUO P7450.
Norton 360 V5.2.1.3, security software

Laptop starts up and can shuts down with out any problem.
If try to hibernation or standby, it take long time accessing disc then crashes. The problem only started when upgraded to service pack 1.

All drivers have been update using driver dating utility by WinZip.

Dump files & system health check report is attached.

Will appreciate any help or suggestion in resolving this issue.

Thank you.

A:Power State Driver Failure on putting PC to Sleep or Hibernation

Two issues

1-Virtally all of these were sysRelated to NETwNv64.sys Wireless WiFi Link Driver from Intel Corporation causing pci.sys to crash. I would re-install with newest driver available.
2-Your Symantec. I would remove and replace with Microsoft Security Essentials.

Symantec is a frequent cause of BSOD's. I would remove and replace it with Microsoft Security Essentials AT LEAST TO TEST
http://us.norton.com/support/kb/web_...080710133834EN

Microsoft Security Essentials - Free Antivirus for Windows

Read other 1 answers
RELEVANCY SCORE 103.2

Hi,

Every time I try to put put my laptop to sleep, hibernate, restart it or shutdown, it stalls for about 10 minutes before giving me a Driver Power State Failure.

Having installed "WhoCrashed" and "Windbg", I was able to determine it was related to "ntkrnlmp.exe", "ndis.sys", "raspppoe.sys" and a vpn driver at one point or another. I "believe" I managed to uninstall the offending vpn driver but of course still overall have the same issue.

This appeared to occur while trying to do a windows update last week but I can't be sure. I presume, there is a out of date or corrupt driver but just can't seem to determine which one.

Many thanks in advance,

Hob

A:Driver Power State Failure on Sleep, Hibernate, Restart or Shutdown

Please remove / disable items from the startup in taskmanager
These programs could interfere with the boot process giving you trouble and increase the boot time.
Daemon tools, Alcohol 120% and Power Archiver Pro uses SCSI Pass Through Direct (SPTD), which is a well known cause for BSOD's.
Please remove Daemon Tools and run the SPTD pass through remover.

Uninstall Daemon ToolsDownload the SPTD standalone installer and follow these steps:
Double click the executable to open itClick on the button shown below

If the button is grayed out, like in the image, there is no more SPTD installation on your system, and you can close the window

   Warning
Programs that claim to update your drivers install either the wrong or corrupted drivers.
If you have installed any driver with Driver Booster 3, please remove them as it may cause trouble.
ONLY install the drivers from your manufacturer!

Please remove your VPN software.

Code:
*** WARNING: Unable to verify timestamp for tap0901.sys
*** ERROR: Module load completed but symbols could not be loaded for tap0901.sys

Read other 0 answers
RELEVANCY SCORE 101.2

my laptop takes 20 to 30 minutes to shut down and comes up with driver power state failure message...i hope you can open the files i attached, was not sure on how to save those files...

A:driver power state failure - user-mode dump

Hi -

Your zip files contained a 2.3 MB user mode dump; not a post-mortem BSOD mini kernel dump.

However, I was able to obtain info that I believe points to your problem. It listed a 0xc0000005 exception = memory access violation.

Code:
Unable to load image C:\WINDOWS\winsxs\x86_microsoft.vc80.mfc_1fc8b3b9a1e18e3b_8.0.50727.6195_none_cbf5e994470a1a8f\mfc80u.dll, Win32 error 0n2
*** WARNING: Unable to verify timestamp for mfc80u.dll
*** ERROR: Module load completed but symbols could not be loaded for mfc80u.dll
*** WARNING: Unable to verify timestamp for nspmain.exe
*** ERROR: Module load completed but symbols could not be loaded for nspmain.exe
*** ERROR: Symbol file could not be found. Defaulted to export symbols for msvcr80.dll -
Unable to load image C:\Program Files\INCAInternet\nProtect Anti-Virus Spyware 3.0\nspavpi.dll, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nspavpi.dll
*** ERROR: Module load completed but symbols could not be loaded for nspavpi.dll
Unable to load image C:\Program Files\INCAInternet\nProtect Anti-Virus Spyware 3.0\nspfwpi.dll, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nspfwpi.dll
*** ERROR: Module load completed but symbols could not be loaded for nspfwpi.dll
Unable to load image C:\Program Files\INCAInternet\nProtect Anti-Virus Spyware 3.0\nspclpi.dll, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nspclpi.dll
*** ERROR: Module load completed but symbols could not be loa... Read more

Read other 5 answers
RELEVANCY SCORE 100.4

Hi,

I've been browsing the site and the internet for a sollution to my problem, but can't seem te find it. There are similar postings, but they're always just a little different. So that's why i posted the new thread.

Since a couple of days i've been experiencing troubles shutting down my PC and using my USB ports. It started when i tried to log onto my work from home. It failed and the IT guy from work told me to reinstall citrix reciever. So I did and I was able to work from home. After finishing and logging out (to get back to my own PC) I found that my USB portst didn't work anymore. I tried rebooting, but af 10 minutes of "shutting down" I got a blue screen: Driver Power State Failure with code 1000009f.

I did the following:
- tried system restore - it failed with different time stamps
- update drivers - they were all up to date the system said
- Malware Bytes, CC Cleaner, MS Essentials, Hitman pro - Did them all, had some minor stuff, fixed that, problem remained.
- SFC/scannow - no problems
- Memory check - no problems

As it is now, the only update I have left is the update to WIN10. However it has tried and failed during a few of the reboots, so that doesn't seem to be and option.

After try all different kinds of things from a lot of posts I decided to refresh my windows install. Did a lot of updating and still the problem remains. Although I now found out that USB devices that are plugged in upon startup work. Once I unplug en replug them, t... Read more

A:BSOD Driver power state failure when shutting down /failure USBports

Are you still having BSOD problem?

Read other 1 answers
RELEVANCY SCORE 100

So I have a pirated windows 8.1 which I have been using for more than a year now. Since the past one week my drivers ( especially the internet driver) keeps crashing and stops detecting any networks. Upon an attempted restart I get the Bsod for which I have attached the files ( All the minidumps.) I run a Dell 5521 R and have updated the drivers, uninstalled and reinstalled them too. Kindly help ASAP as I require my wifi urgently tomorrow.
Note: After restart the drivers get refreshed automatically and start working for sometime. And then the same issue. Please help.VATSAL-Tue_02_09_2016_101910_61.zip

Read other answers
RELEVANCY SCORE 98

My New Years Resolution is to get my laptop back to normal.

I've been having this issue for awhile where if I leave it sitting idle for a couple of minutes and come back, it may or may not cooperate. It frequently gets 'stuck' and becomes unresponsive. Every so often the BSoD pops up and gives the Driver Power State Failure.

I've zipped the documents as per the instructions in jcgriff2's signature.

Any help would be greatly appreciated, Thanks!

A:BSoD - Driver Power State Failure

Sorry, Left out step 5...

-Windows 7 Pro
-32 bit
-Original OS Vista Home Premium 32
-Current OS upgrade via educational system
-Age of hardware 3 1/2 years
-Installed 7 maybe 9-12 months ago... hoping to get rid of this same problem
-CPU: AMD Turion 64x2 TL-64 2.2GHz
-Nvidia GeForce Go7200
-MoBo: ?
-PS: ? (Laptop HP AC adaptor 90W)

Read other 6 answers
RELEVANCY SCORE 98

I've been getting a blue screen for the past week now every time my computer goes to sleep with the Driver Power State Failure message. I've done a lot of research and can see that this is likely due to a faulty driver that isn't updated, and since Windows Update has recently been doing a lot of updating I suspect this is the case. I just need to know which driver is causing the problem. More info:

Problem signature:
Problem Event Name: BlueScreen
OS Version: 6.1.7601.2.1.0.768.3
Locale ID: 1033

Additional information about the problem:
BCCode: 9f
BCP1: 0000000000000003
BCP2: FFFFFA8006B26060
BCP3: FFFFF80000B9C518
BCP4: FFFFFA80099CC970
OS Version: 6_1_7601
Service Pack: 1_0
Product: 768_1

Files that help describe the problem:
C:\Windows\Minidump\101613-28048-01.dmp
C:\Users\Owner\AppData\Local\Temp\WER-207403-0.sysdata.xml

A:Driver Power State Failure BSOD

   Warning
Edit: Please follow Arc's instructions first
Welcome to the Forum.

Check for an update on the driver below:

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa800708fa10, fffff80000b9c518, fffffa8006ea7bd0}

Probably caused by : pci.sys

Followup: MachineOwner
---------

0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

DRIVER_POWER_STATE_FAILURE (9f)
A driver has failed to complete a power IRP within a specific time (usually 10 minutes).
Arguments:
Arg1: 0000000000000003, A device object has been blocking an Irp for too long a time
Arg2: fffffa800708fa10, Physical Device Object of the stack
Arg3: fffff80000b9c518, nt!TRIAGE_9F_POWER on Win7, otherw... Read more

Read other 3 answers
RELEVANCY SCORE 98

I have the same message about power driver state failure occuring radomly every 10 - 30 minutes. However I do not get any error report to let me know what is causing it. Where would this be stored if anywhere? If not what should I do next?

A:BSOD Power Driver State Failure

Hi,

Please follow the http://www.techsupportforum.com/foru...ml#post2545708.

Regards,
Reventon

Read other 1 answers
RELEVANCY SCORE 98

Hi,

? OS: Windows Vista SP2
? 64-bit
? No previous installed OS
? Age of system (hardware) - 2 years, 3 months
? Age of OS installation - have you re-installed the OS? 2 years, 3 months, never re-installed
? CPU - Don't know
? Video Card - nVidia - Display - NVIDIA GeForce 7600 GS
? MotherBoard - Don't know
? Power Supply - Don't know

The problem is sometimes when I want to shut my computer down it takes AGES. After waiting about 20 minutes, it will just BSOD and be fine when I re-boot it. Sometimes, but not as often, after I turn on my computer back from sleep mode it will go very slow for about 20 minutes then just randomly BSOD.

Thanks in advance to anyone that can help!

A:BSOD Driver Power State Failure

Hi -

The BSOD dump shows OS corruption. The likely cause is unknown hardware failure.

Run memtest86+ --> http://www.memtest.org/#downiso
- one stick at a time, alternate the slots

Run chkdsk /r

Run HDD diagnostics

Regards. . .

jcgriff2

.



Vista x64 SP2 - - BSOD BUGCHECK 0x9f (0x3,,,)

Code:

Opened log file 'C:\Users\PalmDesert7\_jcgriff2_\dbug\__Kernel__\_99-dbug.txt'

Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.


Loading Dump File [C:\Users\PalmDesert7\_jcgriff2_\dbug\__Kernel__\Mini041310-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows Server 2008/Windows Vista Kernel Version 6002 (Service Pack 2) MP (2 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS Personal
Built by: 6002.18160.amd64fre.vistasp2_gdr.091208-0542
Machine Name:
Kernel base = 0xfffff800`0204e000 PsLoadedModuleList = 0xfffff800`02212dd0
Debug session time: Tue Apr 13 21:25:44.807 2010 (GMT-4)
System Uptime: 7 days 0:29:19.048
Loading Kernel Symbols
..........................................
Loading User Symbols
*******************************************************************************
* *
* Bugcheck Analysis... Read more

Read other 9 answers
RELEVANCY SCORE 98

Morning, all.

I could use a bit of help--I've been having a number of BSODs lately, and they always relate to a driver power state failure. Doing my own research has not really been as productive as I'd like.

Of note: this really only happens when I open the laptop back up after leaving it alone for some hours (when I wake up, and occasionally when I get back from work). The computer will run fine for about 5-10 minutes, and then I get a BSOD. I'm running Vista, SP2, on a Dell Inspiron 1525--haven't really had any major problems with this before.

I'm attaching a zip of the minidump and the msinfo32 file as I saw requested in another thread. Many thanks for any help!

Best
writingmiles

A:BSOD and Driver Power State Failure

For more specific troubleshooting, please follow the blue screen posting instructions to provide your full reports.http://www.techsupportforum.com/foru...ta-452654.html
Crashes point to your M-Audio KeyStudio device and/or its drivers. It is conflicting with your PreSonus Inspire WDM device and/or its drivers.

-----

Read other 2 answers
RELEVANCY SCORE 98

? Windows 7
? x64
? 1month
? i7 930
? gtx 580
? asus rampage III gene x58
? enermax galaxy 850w DXX

when i shut down my pc takes 80% of shutdowns 14+ min to close down after showing a driver power state failure bsod, please help me find a solution,

thank you
damien short

A:driver power state failure bsod

Hello,

It appears your Creative Audio drivers are the cause, from the looks of the dump. I see they are rather old:
Code:
CT20XUT.DLL Thu Aug 21 12:40:17 2008 (48AD9A71)
ctaud2k.sys Thu Aug 21 12:38:56 2008 (48AD9A20)
CTEXFIFX.DLL Thu Aug 21 12:40:11 2008 (48AD9A6B)
CTHWIUT.DLL Thu Aug 21 12:40:21 2008 (48AD9A75)
ctoss2k.sys Thu Aug 21 12:36:31 2008 (48AD998F)
ctprxy2k.sys Thu Aug 21 12:38:58 2008 (48AD9A22)
ctsfm2k.sys Thu Aug 21 12:36:16 2008 (48AD9980)
Install updated drivers from here: Auzentech, Inc. Sound Cards. Audio You Can Believe In. World First soundcards for Music, HTPC, and Gaming.

If that doesn't work, upload a new report, and we'll go from there.

...Summary of the dumps:

Code:

Built by: 7600.16617.amd64fre.win7_gdr.100618-1621
Debug session time: Wed Jan 5 19:17:22.447 2011 (UTC - 5:00)
System Uptime: 0 days 6:05:05.649
Probably caused by : pci.sys
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
FAILURE_BUCKET_ID: X64_0x9F_3_ctaud2k_IMAGE_pci.sys
??????????????????????????????????????????????????????????????????????????????????????``

Read other 2 answers
RELEVANCY SCORE 98

Hello,

I'm brand new to the forums. Usually I'm able to sort my own computer problems (with the help of good ol' Google). However I've been stuck with this for some time now. BSOD, Driver_power_state_failure. I can't really pin point a particular time this happens I'm afraid. I built this PC myself (my first one) about 7-8 months ago(?) and haven't really had any problems.

So far, I've reinstalled windows and updated all my drivers as recommended from many Google searches but I am still getting the same BSOD and frankly if I can't find the answer via Google I'm pretty much buggered . After reading the posting instructions I've used the diagnostic tool, so I'll attach the zip.

Any help or advice would be most welcome and appreciated.

Thanks very much guys.

Steve

A:BSOD - Driver power state failure

Vayzaroth,

Welcome to SevenForums.

Help us to help you by carrying out the following:
Update your SevenForums System Specs
User CP (located on the top menu bar) |
Your Profile | Edit System Spec (left-hand column)

To gather info, use Speccy (my favorite) or SIW or System Info

In the System Manufacturer Block, enter:
Manufacturer and Model and
ADD the word laptop, desktop, netbook or tablet.
For example:
Toshiba Satellite L305D notebook.

Provide full windows version info, for example:
MS Windows 7 Ultimate SP1 64-bit

Use the ?Other Info? block for Optical Reader,
Mouse, touchpad, wifi adapter, speakers, monitor, etc

Scroll down and click on SAVE CHANGES.

You will find that in Speccy, you can select info from the display
using your mouse/touchpad and then paste that info into your specs.

SIW is a marvelous program, but the free version does not offer
this capability.
===================================================
thanks
karl

Read other 9 answers
RELEVANCY SCORE 98

i get this at least once a day because i dont turn my computer off and it gets really frustrating sometimes.

attached is the minidump file.

please if somebody could help me out :)

A:BSOD power state driver failure

FYI - I have severe eye problems. If I don't respond to your postings, please PM another staff member for assistance.

Please provide this info for a more complete analysis: http://www.techsupportforum.com/foru...ta-452654.html

The memory dump points to your network drivers as the cause. In most cases updating these will fix the problem.

BUT, the antivirus/Internet Security application that you use can also cause this. Uninstalling it and installing a freshly downloaded copy can fix that.

Also, this may be caused by a hardware problem. But the diagnosis of that is done by trying the above things.

Another possibility is the Gigabyte EasyTune software - but I'm not 100% sure that that's involved in this situation. To test, uninstall it and see if it stops the BSOD's.

Finally, the memory dump (crash) seems to have occurred during the sleep/hibernate transition. As such you should also reinstall the chipset, storage, and video drivers for your system.

Good luck!

BSOD BUGCHECK SUMMARY

Code:

Loading Dump File [C:\Users\FUBAR\_jcgriff2_\dbug\__Kernel__\092611-22854-01.dmp]
Built by: 7601.17640.amd64fre.win7sp1_gdr.110622-1506
Debug session time: Mon Sep 26 11:52:36.081 2011 (UTC - 4:00)
System Uptime: 0 days 1:23:55.251
Probably caused by : pci.sys
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
FAILURE_BUCKET_ID: X64_0x9F_3_Rt64win7_IMAGE_pci.sys
Bugcheck code 0000009F
Arguments 00000000`00000003 fffffa80`03ab1a10 fffff800`044... Read more

Read other 1 answers
RELEVANCY SCORE 98

Hi,

My laptop goes to BSOD what seems like several times a week and drives drives me nuts. We've had the laptop exactly two years now and it seems to be getting worse and more frequent. I've tried a completely fresh/clean install of Windows 7 64-bit, but no luck.

The problem happens about 70-80% of the time when the computer has gone to sleep and we're trying to wake it up using any button on the keyboard or the power button (doesn't matter which one). Less often, it will completely freeze up while we're browsing the internet (Chrome...we can switch between windows/desktop and scroll the cursor for a minute or so before the BSOD comes up).

The BSOD error comes up as: "Driver Power State Failure". Attached is the ZIP file as instructed.

Any help would be greatly appreciated.

Thanks,
Jeremy

A:Driver Power State Failure BSOD

Hi Neons97.

You need to update Fresco Logic xHCI (USB3) Controller FL1000 Series driver. No feasible update is available in ASUSTeK Computer Inc. -Support- Drivers and Download N53SV. So try the
Fresco Logic FL-1000/1009 USB 3.0 Controllers from Station-Drivers - Fresco Logic (drivers).

Also turn off USB selective suspend.
USB Selective Suspend - Turn On or Off

BTW, your RAM seems to be of odd volume.

Code:
Installed Physical Memory (RAM) 14.0 GB
Publish a Speccy snapshot : Speccy - Publish Snapshot of your System Specs .

Let us know the results.
__________________________________________________________________________________

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck 9F, {3, fffffa800fced060, fffff80000b9c3d8, fffffa80153e7010}

Probably caused by : usbhub.sys

Followup: MachineOwner
---------

0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis ... Read more

Read other 7 answers
RELEVANCY SCORE 98

I've gotten the blue screen 3x in the last 24 hours. I need help. Thank you.

A:BSOD Driver Power State Failure

Hello Kincaidio, and welcome to Seven Forums.

Please read the instructions below, and post back with the need information. Afterwards, hopefully someone will be able to help soon.

Blue Screen of Death (BSOD) Posting Instructions

Read other 1 answers
RELEVANCY SCORE 98

I am getting these "driver power state failure" crashes with increasing frequency. I suspect it's a driver conflict involving my M-Audio Fast Track Ultra (music recording interface), which is connected via USB.

My computer is an HP 671-340US notebook, bought in June or July 2010, with Windows 7 Home Premium (and a whole bunch of HP bloatware!) already installed. I have eliminated some of the HP crap because it constantly interrupted my work, and shut down my computer right in the middle of what I was doing, if I missed the message balloon. Don't know if that contriubuted to the problem. I updated all the drivers and Win7 yesterday and today. Crashed again this morning. No hardware upgrades; using it the way it came.

I have attached all the system specs and diagnostics reports you requested.

If I missed anything, please let me know.

Thanks!

Charlie

A:BSOD Driver Power State Failure

  
Quote: Originally Posted by jgm34787


I am getting these "driver power state failure" crashes with increasing frequency. I suspect it's a driver conflict involving my M-Audio Fast Track Ultra (music recording interface), which is connected via USB.

My computer is an HP 671-340US notebook, bought in June or July 2010, with Windows 7 Home Premium (and a whole bunch of HP bloatware!) already installed. I have eliminated some of the HP crap because it constantly interrupted my work, and shut down my computer right in the middle of what I was doing, if I missed the message balloon. Don't know if that contriubuted to the problem. I updated all the drivers and Win7 yesterday and today. Crashed again this morning. No hardware upgrades; using it the way it came.

I have attached all the system specs and diagnostics reports you requested.

If I missed anything, please let me know.

Thanks!

Charlie


Hi charlie and welcome.

You are of course correct about M-audio. It is blamed. It may be conflicting with one of the older drivers installed. I would update both M-audio and these old drivers. Some of these drivers including y our raid driver is from as far back as 2005.


Code:
iirsp.sys 12/13/2005 5:47:54 PM fffff880`015a0000 fffff880`015b1000 0x00011000 0x439f418a
nfrd960.sys 6/6/2006 5:11:48 PM fffff880`016b3000 fffff880`016c3000 0x00010000 0x4485ef94 ... Read more

Read other 2 answers
RELEVANCY SCORE 98

I updated my HP Pavilion from Vista to Win 7 and since then have experienced a Driver Power State failure crash on a regular basis.

System Specs are: 3 GB Ram, 32 OS, Intel Quad Core 2.3 ghz

I have hopefully attached the dump files that will help in diagnosing the problem.

Any help would be truly appreciated! Thanks!!!


Bob

A:Driver power state failure BSOD

  
Quote: Originally Posted by rbdig


I updated my HP Pavilion from Vista to Win 7 and since then have experienced a Driver Power State failure crash on a regular basis.

System Specs are: 3 GB Ram, 32 OS, Intel Quad Core 2.3 ghz

I have hopefully attached the dump files that will help in diagnosing the problem.

Any help would be truly appreciated! Thanks!!!


Bob


Hi Bob

We need the actual DMP file. yours is an unreadable html file.

Let us know if you need help

Ken

Read other 2 answers
RELEVANCY SCORE 98

Hi,

I had a bsod the other day and it said "Driver power state failure" stop 0x0000009f. Can anybody help me?

A:BSOD Driver power state failure

Hi,

BSOD mentions win32k.sys - a Microsoft driver which is probably not the real cause.

So, run the driver verifier to try and get the real cause to show itself.

Driver Verifier - Enable and Disable

Also remove SPTD.sys which is known to cause BSODs; remove Daemon Tools, then use this SPTD installer to remove it (pick the uninstall option when you run the installer): DuplexSecure - Downloads

When you get a few more BSODs then please follow these Blue Screen of Death (BSOD) Posting Instructions exactly.

Regards,
Reventon

BUGCHECK SUMMARY

Code:

Built by: 7600.16617.amd64fre.win7_gdr.100618-1621
Debug session time: Sat Nov 20 12:56:49.103 2010 (GMT+13)
System Uptime: 1 days 12:26:37.883
*** WARNING: Unable to verify timestamp for win32k.sys
*** ERROR: Module load completed but symbols could not be loaded for win32k.sys
Probably caused by : memory_corruption
DEFAULT_BUCKET_ID: CODE_CORRUPTION
BUGCHECK_STR: 0x9F
PROCESS_NAME: System
Bugcheck code 1000009F
Arguments 00000000`00000004 00000000`00000258 fffffa80`03d03040 fffff800`046614d0
??????????????????????????????????????????????????????????????????????????????????????``

Read other 2 answers
RELEVANCY SCORE 98

I am having this BSOD since 14 days , my laptop HP dv6 6165 tx is new and a month old and i play games on it for almost 2-3 hours daily it has OEM windows 7 64 bit installed on it. I have attched the mini dump report files and the perform/report files in the attched file zip folder ,please help me.

A:BSOD Driver power state failure

Problematic software:
Code:
tuneuputilitiesapp64.exe c:\program files (x86)\tuneup utilities 2012\tuneuputilitiesapp64.exe 3972 8 200 1380 12-04-2012 08:09 12.0.2012.117 1.28 MB (1,337,664 bytes) 12-10-2011 18:14
tuneuputilitiesservice64.exe c:\program files (x86)\tuneup utilities 2012\tuneuputilitiesservice64.exe 1184 8 200 1380 12-04-2012 08:08 12.0.2012.117 1.98 MB (2,072,896 bytes) 12-10-2011 18:14
Many of us on the forums actually do not recommend automated optimization tools for Windows 7. Windows 7 does a much better job of handling its own optimization than its predecessors did. We especially do not recommend registry cleaning as an "optimization" step because automated registry cleaning causes more harm to the registry than it actually repairs.

In the future, if you need help optimizing Windows 7, please post a thread in Performance & Maintenance - Windows 7 Forums or follow the tutorial enclosed in that forum to Optimize Windows 7.
Security Software (to check that it is installed and working properly; nothing needs to be done with this information at this time):
Code:
msmpeng.exe c:\program files\microsoft security client\msmpeng.exe 684 8 200 1380 12-04-2012 08:08 4.0.1512.0 12.50 KB (12,800 bytes) 28-02-2012 12:24
msseces.exe c:\program files\microsoft security client\msseces.exe 3140 8 200 1380 12-04-2012 08:09 4.0.1512.0 1.21 MB (1,270,656 bytes) 28-02-2012 12:28


Code:
Microsoft (R) Windows Debugger Version 6.12.0002.633 AMD64
Co... Read more

Read other 9 answers
RELEVANCY SCORE 98

? Windows 7
? x64
? Original OS
? OEM
? about 1 year old
? never reinstalled

? intel core 2 duo p8700 @2.53GHz
? Nvidia geforce gtx 260m

? gateway
? p7908u
Hi there, I've been frequently getting BSoD's more and more as of late and I'm not quite sure why, any possible help?
And for some reason my perfmon report was not loading so unfortunately it's not in the zip. :/

A:driver power state failure BSoD

You have 26 BSOD (24 are from March 29th) that all point to your O2Micro memory card reader. The crashes start on March 28th. Is that when you installed this? Please either disable or uninstall this device

Please update your computer to SP1 - How to update to SP1
*Updating to SP1 might fix the issue with the card reader. You can re-install it after you update and see if the crashes continue


Code:
sptd.sys Sun Oct 11 16:55:14 2009 (4AD24632)
yk62x64.sys Wed May 20 04:14:06 2009 (4A13BBCE)
Uninstall Daemon Tools. It is a known BSOD maker in Windows 7. You the tool found here to make sure it is completely removed.


Code:
iaStor.sys Thu Jun 04 21:53:40 2009 (4A287AA4)

Update your Intel storage drivers - here


Code:
NETw5s64.sys Wed Jan 13 11:37:13 2010 (4B4DF6B9)
Update your Intel WiFi drivers - here


Code:
nvlddmkm.sys Fri Jul 09 17:15:58 2010 (4C37918E)
Update your Nvidia video card drivers - here


Code:
RTKVHD64.sys Wed Aug 05 05:46:28 2009 (4A7954F4)
Update your Realtek HD Audio drivers - here

Partial summary of dumps

Code:
Built by: 7600.16695.amd64fre.win7_gdr.101026-1503
Debug session time: Tue Mar 29 08:27:01.390 2011 (UTC - 4:00)
System Uptime: 0 days 0:12:52.058
*** WARNING: Unable to verify timestamp for o2sdx64.sys
*** ERROR: Module load completed but symbols could not be loaded for o2sdx64.sys
Probably caused by : o2sdx64.sys
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0x9F
PROC... Read more

Read other 1 answers
RELEVANCY SCORE 98

I've been experiencing issues with my computer. It tends to blue screen and reads "Driver_POWER_STATE_FAILURE". I've tried to run some scans and diagnostics and even backed up my PC and then rebooted it with factory new settings, but it is still BSOD. I have a dump file, but I cannot post it because it says I do not have permission to open or attach it. Any help would be greatly appreciated!


Thanks!

A:Driver Power State Failure - BSOD

You need to follow these directions
We do need the DMP file as it contains the only record of the sequence of events leading up to the crash, what drivers were loaded, and what was responsible.
Please attach the DMP files to your next post not to post one.

If you are overclocking STOP

You may be able to get the DMP files without crashing by booting into safe mode (F8) with networking.

To enable us to assist you with your computer's BSOD symptoms, upload the contents of your "\Windows\Minidump" folder.

The procedure:





Quote:
* Copy the contents of \Windows\Minidump to another (temporary) location somewhere on your machine.
* Zip up the copy.
* Attach the ZIP archive to your post using the "paperclip" (file attachments) button.
*If the files are too large please upload them to a file sharing service like "Rapidshare" and put a link to them in your reply.


To ensure minidumps are enabled:





Quote:
* Go to Start, in the Search Box type: sysdm.cpl, press Enter.
* Under the Advanced tab, click on the Startup and Recovery Settings... button.
* Ensure that Automatically restart is unchecked.
* Under the Write Debugging Information header select Small memory dump (256 kB) in the dropdown box (the 256kb varies).
* Ensure that the Small Dump Directory is listed as %systemroot%\Minidump.
* OK your way out.
* Reboot if changes have been made.

Read other 3 answers
RELEVANCY SCORE 98

Hi,

I'm new to this forum but i hope you can help with BSOD issues on my windows 7 Laptop.

I have a HP HDX18 Laptop that is about 8months old. I bought it with Vista home premium and upgraded to windows 7 home premium when it was released. As soon as i upgraded i started having blue screen of death problems (BSOD) problems. The laptop became unusable as it would crash intermittantly. It turned out to be my anti-virus software, Zone Alarm and so i swapped to Kaspersky.

About two months ago the machine started running slowly, locking up and crashing. I wasn't able to complete any tasks, there didn't seem to be any system restore points and it was completely unusable and so i decided i would recover to factory condition (Vista) and start again. I have done this and reloaded Windows 7 update and normal windows software. I also upgraded again to windows 7 ultimate so i would have networking capability as my other computers are XP pro and a Mac and the networking function in Win 7 home premium is worse than useless.

This all completed successfully last week and within a few days i am again having problems. I cannot shutdown my laptop, it will hang (saying 'shutting down') for about five minutes and then BSOD. I have attached the minidumps files using the SF Diagnostic Tool from this forum.

I also cannot use any usb ports, backup and have trouble with some proprietory HP software.

First things first, i need to find out why i cannot shut down so hopefully someone can ... Read more

A:BSOD - driver power state failure

  
Quote: Originally Posted by onyxquark


Hi,

I'm new to this forum but i hope you can help with BSOD issues on my windows 7 Laptop.

I have a HP HDX18 Laptop that is about 8months old. I bought it with Vista home premium and upgraded to windows 7 home premium when it was released. As soon as i upgraded i started having blue screen of death problems (BSOD) problems. The laptop became unusable as it would crash intermittantly. It turned out to be my anti-virus software, Zone Alarm and so i swapped to Kaspersky.

About two months ago the machine started running slowly, locking up and crashing. I wasn't able to complete any tasks, there didn't seem to be any system restore points and it was completely unusable and so i decided i would recover to factory condition (Vista) and start again. I have done this and reloaded Windows 7 update and normal windows software. I also upgraded again to windows 7 ultimate so i would have networking capability as my other computers are XP pro and a Mac and the networking function in Win 7 home premium is worse than useless.

This all completed successfully last week and within a few days i am again having problems. I cannot shutdown my laptop, it will hang (saying 'shutting down') for about five minutes and then BSOD. I have attached the minidumps files using the SF Diagnostic Tool from this forum.

I also cannot use any usb ports, backup and have trouble with some proprietory HP software.

First things... Read more

Read other 9 answers
RELEVANCY SCORE 98

Hi. Im having a problem with my computer. The last few days I have been having a new BSOD problem. I have been getting a driver power state failure for a while and I had it fixed but when I updated my graphics card drivers it started again and I cant figure out why. Any help would be much appreciated.

A:BSOD Driver Power State Failure

Welcome to the forum.

Based on the bugcheck, I would recommend you follow and complete the steps given below:





Quote:
1. If you are overclocking any hardware, please stop. Reset any changed values back to default and reset/clear CMOS: Clear CMOS - 3 Ways to Clear the CMOS - Reset BIOS. Uninstall any overclocking tool as these can also be a reason of blue screens.

2. Uninstall your current antivirus software. It can be a cause of BSOD very often. Please remove it with its removal tool and use Microsoft Security Essentials in its place. Malwarebytes is a great combination with it. Go through this thread for more info.

3. Run Disk Check with both boxes checked for all HDDs and with Automatically fix file system errors. Post back your logs for the checks after finding them using Check Disk (chkdsk) - Read Event Viewer Log

4. Run SFC /SCANNOW Command - System File Checker to check windows for integrity violations. Run it up to three times to fix all errors. Post back if it continues to show errors after a fourth run or if the first run comes back with no integrity violations.

5. Make scans with Kaspersky TDSskiller and ESET Online scanner.

6. Perform a Clean Start up, this will help avoid any problematic applications from bugging the system.

7. Use Revo Uninstaller Free to uninstall stubborn software. Opt for Advanced Mode and uninstall the software, delete the leftover registry entries.

8. Use Crystal Disk Info to upload a screenshot o... Read more

Read other 1 answers