Over 1 million tech questions and answers.

E550 and ThinkPad OneLink Pro - external monitors ...

Q: E550 and ThinkPad OneLink Pro - external monitors ...

I have a ThinkPad E550 laptop connected to two Acer V246HL monitors via a ThinkPad OneLink Pro dock. One monitor is connected via DVI/HDMI to the dock and the other connected either via VGA or DVI/HDMI directly into the laptop. When both are connected via DVI/HDMI only one monitor will be detected. When one is connected via VGA both monitors are detected, however the one connected via VGA will flicker or blink off and on. Disconnecting the ThinkPad dock solves this issue. I have tried the following:Uninstalled and reinstalled graphics driversUpdated dock firmwareRun updates on graphics driversChecked different cablesChecked different monitorsChecked different dockChecked different laptopRun Lenovo VGA fix The Lenovo VGA fix would not complete and ended up in error loop. After advice from the internet I unplugged the dock and tried again, but failed. I then unplugged everything but the VGA cable and tried again, but failed. I unplugged all peripherals and tried again, but still failed. Errors include "Invalid AUX device" and"Enable Aux2 Reg Failed".Finally I redownloaded the fix, unblocked everything before unzipping then ran as Administrator, however it all still failed. Any other advice? I can run off battery for a while but not for a full working day.

Read other answers
RELEVANCY SCORE 200
Preferred Solution: E550 and ThinkPad OneLink Pro - external monitors ...

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

RELEVANCY SCORE 100

I have the exact same equipment at home and at work and yet the resolution on my second monitor at work will not go to the 3840 x 2160 that I have at home. Both locations have:1. X1 Yoga (first gen, model number 20FQ002YUS) -- It's the same laptop that I take between home and work2. ThinkPad OneLink+ Dock (model number DU9047S1)3. Two (2) Asus monitors (model number PB287Q) that go to 3840 x 2160 max resolution, connected to the OneLink+ Dock via DiplayPort cables I've been running this configuation with NO PROBLEM at home for the past 9 months.  So I recently purchased a new OneLink+ Dock and two new monitors for my work office and while one monitor will go to 3840 x 2160, the other will not go above 1920 x 1080, UNLESS, I use a mini DisplayPort cable from the second monitor directly into the X1 Yoga (bypassing the OneLink+ Dock) HERE'S WHAT'S BAFFLING: I assumed it was the dock and so I brought the one from home to work and found I had the SAME problem, suggesting it was the second monitor.   But I exchanged the second monitor for a new one and still have the same problem.  The docks are running the most current firmware. I'll send a gift card to your favorite coffee house if you can solve this mystery.  Thanks!

Read other answers
RELEVANCY SCORE 100

I have lenovo thinkpad x1 yoga.I have one connect +VGA and RJ45 adapter. i am trying to connect the 2 external display  apart from laptop screen here is my input:one external display is connected to onelink via VGA and another display connect via HDMI.but this dosen't work whenever i plug either onelink or hdmi one of the external monitor will be switched off. isn't it possible to use onelink and HDMI together.??I am stuck here. 

A:Lenovo Thinkpad X1 yoga 1st gen connect 2 external monitors apart from laptop display via onelink VG

Hi,
 
The way I read the X1YG1 base specs it supports two independent monitors.  Apologies, but I can't quite parse your post.  Does "apart from laptop screen" mean that you want 3 monitors total, or two and the laptops's display is off?
 
supports external digital monitor via HDMI or Mini DisplayPort;supports dual independent displays;
 
Z.

Read other 1 answers
RELEVANCY SCORE 98.4

Hi Guys! We got 6 Thinkpad E550, all with OneLink Pro Docks.All of them are connected with one or two external Monitors (only DP or DVI).From time to time the Monitors starts flickering/blinking black. Its not reproducable. I've already patched all drivers and firmwares. OS was Windows 7 (64) and is now Windows 10 (64). Problems still exists - ON ALL SIX DEVICES, different monitors, cables ect..Actual firmware seem to fix exactly this problem on x1 carbon notebooks:https://download.lenovo.com/ibmdl/pub/pc/pccbbs/options/tp_onelink_pro_dock_fw.txtPlease release a firmware with fix for E550! 

Read other answers
RELEVANCY SCORE 98.4

Hardware:Thinkpad E55024" LG & BenQ Monitor (same error) (1920x1080 but error also on all other resolutions)ThinkPad OneLink Dock with: Keyboard, Mouse, LAN, AC, DVI-to-HDMI Adapter for DVI cable Scenario:Hello everyone, I've been working at the IT-department of a hospital and some of the workers are gettings E550 ThinkPads hooked up to Docking stations so that they can easily plug it off when they need to take it somewhere.They run with 24" LG Monitors and ideally you'd just turn on the ThinkPad via the Docking Station and have everything ready in just about a minute. Error:However it doesn't work out that smoothly. We've hooked up two different E550 ThinkPads with two different OneLink Docks on to two different monitors, both of them showing the same errors.A LOT of graphic changes result in the same error message.LG: "Out of range, 40.4kHz, something Hz" (also went to 40,6kHz, not steady numbers)BenQ: "Out of range" When does it happen? A lot of times. When I change graphic options (primary screen, resolutions, dual screen mode, etc), when I reboot, even when I accessed the device manager once.The worst thing is the rebooting though, everything else I got sorted out to the point where a normal user wouldn't really trigger that. However I cannot expect the workers to deal with that every time they wanna open up their workplace. I see the screen up to the point where it says "Windows is loading", I see the icon move and as soon as it finishes - b... Read more

Read other answers
RELEVANCY SCORE 93.6

Hi, Everyone. Got me a nice little x270 to replace my old x201.  Happy enough with the machine, but getting it connected to my accessories (monitor, keyb, mouse, ethernet) is a bit of a chore. This machine appears to have a "proper" dock port on the bottom.  Is there a compatible ultradock available for the model 20HN x270?  By proper - I mean, Not USB.  A nice dock I can simply drop the machine into when I'm at the home office.. Thanks!

Read other answers
RELEVANCY SCORE 93.6

I have read a lot and tried updating the firmware - nothing works.When I put the laptop in the docking station - it does not recognize the monitar and also says AC power is not connected when it is. Help appreciated!

Read other answers
RELEVANCY SCORE 84.8

Hello everyone. I have an X1 Carbon 2nd generation, and two lenovo monitors with a OneLink Pro Docking station.  Docking station has 1 DVI and 1 DP.Monitors have 1 HDMI, 1 DP, 1 VGA (for each) First Monitor connected with DP-adapted-DVI to the docking station.Second Monitor connected with DP port to the docking station.  I connected my closed laptop to the docking station,  and just first monitor works.  What should I do to use my other monitor too? Thank you so much. 













Solved!

Go to Solution.

A:ThinkPad OneLink Pro Dock multiple Monitors

Sorry. Problem solved! The DVI - DP adapter changed with a DVI - HDMI adapter. Now it works fine, just need some minutes after first connection.  Thanks.

Read other 1 answers
RELEVANCY SCORE 82.8

Hi.I'm using my X1 Yoga with a Onelink+ docking station and 2 external monitors on Display Port. The description of the docking station states that there can be up to 3 monitors including the system display. My X1 Yoga is always closed when I'm at home so that I'm just using the external monitors whereas 1 of them acts as the system display.In this case, could I attach a third external monitor to the VGA port of the docking station? Many thanks in advance.

Read other answers
RELEVANCY SCORE 80.8

I'm unable to get my X1 Yoga to detect external monitors when plugged into the OneLink+ dock. This started occuring when my computer upgraded to the creators update. I thought I found a thread of others with the same issue (linked below), but it turns out I was waiting for a fix that didn't apply to me. I'm super frustrated right now. Stuff I've tried so far.1. Updated all drivers using Lenovo Service Bridge (even optional drivers)2. Installed the Fall Creators update preview (after being told it would fix the issue)3. Completely reinstalled Windows4. A Single VGA monitor5. A Single Display Port Monitor6. 6 different cables At this point I'm convinced there's an issue with the dock. There's a firmware update available for it, but you can't install it unless it is actively connected to a monitor (go figure).  When attempting to install, I get the code 255 "Can't connect to Synaptics VMMxxxx DP hub IC" If anyone has any sugestions, I'd greatly appreciate it. It used to work perfectly, then about the time I installed the creators update it started getting flaky, now I can't get it to work at all. Previous thread I was following. Note that I'm linking to a post where they show the dock working (annoying).https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/Windows-10-creator-update-breaks-Lenovo-...

Read other answers
RELEVANCY SCORE 80.8

Hello everybody,i am posting here because i really went through the whole www and still i have this issue, which is the following: My configuration is:X1 Carbon 3rd Gen (Windows 10 64bit)OneLink+ docking2 x ThinkVision P27q-10 monitors. The problem:When i connect both monitors to the dock, i get only one running / working.The only way I get both monitors working is if i connect the second one on my miniDP port directly on the laptop. And in this configuration i can have all three monitors working (laptop display + 2 external) Obviously i want to have them both connected on the docking station and use it properly. Thanks in advance for any solutions / suggestions. Dean

Read other answers
RELEVANCY SCORE 80.8

When I'm charging my Thinkpad E550 and I connect it to any external monitor with a VGA cable, the external monitor flickers constantly such that the external monitor cannot be used for any meaningful work. However, when I remove the charger, the constant flickering stops and the external monitor could be used though the screen still flickers/blinks for only about 4 seconds every 50 minutes or so. Disappointingly, using the laptop on battery all the time is not healthy for the laptop's battery but that's the choice I have if I need to use an external monitor. I have tried to use a 2-pronged adapter to plug the monitors into the mains but I still experience the flickering until I remove the charger. Does anyone have a solution? Thank you.  











Solved!
Go to Solution.

A:Thinkpad E550: External monitor flickers constantl...

My external display does the same thing, but if I unplug the charger and the flashing constantly, momentarily displays the desktop and then 3 seconds off. I tried to reinstall Intel HD driver, but the same result, ATI driver i have latest.Any idea?

Read other 9 answers
RELEVANCY SCORE 77.2

My X1 Yoga 1st Gen runs Windows 10, i wanted to connect 3 external monitors through OneLink+ dock( It has 2 DP and 1 VGA output ports) but for some reason only 2 monitors get connected and working but not the 3rd one, i tried connecting the 3rd monitor directly to the laptop through HDMI it didnt work either, do i need to do something to make all 3 monitors to work?

Read other answers
RELEVANCY SCORE 75.2

I have owned my Yoga S1 for several years now and apart from the endless early issues the docks (and many replacements), the stupid placing of the Ctrl key (still annoys me) and a problem i had with a repair (which to be fair was handled very well in the end - customer service was great) I've been happy.Except one things - power management.This morning, I came to my Yoga and the red light was glowing on the i in thinkpad, key board locks were on: touch keys (on most of my other computers pressing space a few times wakes from sleep state), nothing, press power button nothing, press button on dock - nothing., tried restart button on the dock - still nothing.So I do what, now that I think about it, I do about 75% of the time when returning to my yoga - hold the power button for 9 seconds and force a BIOS crash reset. I have applied all the drivers religiously over the years, BIOS updates Windows in up to date (Creator edition now) fully patched. I have tried the confusing variety of Lenovo bits that seem to part duplicate and part confuse existing Windows functionality. So, and with respect, please don't post "have you tried applying" ... unless you happen to know that this is specific fix for something - I reckon I have been through the random try everything approach. What I'd like is: 1) to be able to work at my desk - touch something to say "I am away" and have power saved my two external monitors switch off but for the machine to go back to where I was when I ... Read more

Read other answers
RELEVANCY SCORE 75.2

I have owned my Yoga S1 for several years now and apart from the endless early issues the docks (and many replacements), the stupid placing of the Ctrl key (still annoys me) and a problem i had with a repair (which to be fair was handled very well in the end - customer service was great) I've been happy.Except one things - power management.This morning, I came to my Yoga and the red light was glowing on the i in thinkpad, key board locks were on: touch keys (on most of my other computers pressing space a few times wakes from sleep state), nothing, press power button nothing, press button on dock - nothing., tried restart button on the dock - still nothing.So I do what, now that I think about it, I do about 75% of the time when returning to my yoga - hold the power button for 9 seconds and force a BIOS crash reset. I have applied all the drivers religiously over the years, BIOS updates Windows in up to date (Creator edition now) fully patched. I have tried the confusing variety of Lenovo bits that seem to part duplicate and part confuse existing Windows functionality. So, and with respect, please don't post "have you tried applying" ... unless you happen to know that this is specific fix for something - I reckon I have been through the random try everything approach. What I'd like is: 1) to be able to work at my desk - touch something to say "I am away" and have power saved my two external monitors switch off but for the machine to go back to where I was when I ... Read more

Read other answers
RELEVANCY SCORE 74.8

I have a Thinkpad T430 type 23474W4 and a Thinkpad mini dock series 3 type 4338-15U. I already have a Lenovo LEN LS2223wC monitor hooked up to it through one of the DVI ports. I have a a Lenovo LT1952p Monitor that I would like to use as a second external monitor. Both monitors work individually through either DVI or VGA. However, I can't get them to both work at the same time no matter what configuration I use. I was told they didn't have to be identical monitors to work together. What am I doing wrong? 

Read other answers
RELEVANCY SCORE 69.6

Hello,  I am trying to connect 2 external monitors to my docking station via DP and DVI.  Configuration:  OS: Win7 Laptop: T450 (intel 5500) Docking Station: ThinkPad PRO 40A1 External monitor available connections: VGA,DVI,HDMI  What works:laptop screen + external monitor via VGA + monitor screen via DVI (pasive) laptop screen + external monitor via VGA + monitor screen via DP - HDMI cablelaptop screen + external monitor via VGA + monitor screen via DP - DVI cable (active) What do I want to achieve:laptop screen + external monitor via DP-HDMI / DP-DVI + monitor screen via DVI  Basically I don't want VGA because I have a bad output (the image is a bit blury and after 8 hours of working it can be tiresome).  Any tips/ Hints?  Thank you.

A:ThinkPad with 2 external monitors

Is there any update on this?  Thank you.

Read other 6 answers
RELEVANCY SCORE 69.6

How many external monitors does this machine support simultaneously, without a dock?It is a December 2017 / January 2018 build P51, with an NVIDIA Quadro M1200 4GB GDDR5 graphics card.Native display is 3840x2160.Available display ports are HDMI, Mini DisplayPort, and USB-C.Operating system is Windows 10 Pro. Thanks in advance.

Read other answers
RELEVANCY SCORE 68.8

Have already updated the Bios on the computer as well as installed the recent firmware update available for the docking station. Any other suggestions?

Read other answers
RELEVANCY SCORE 68.8

Is there any official and correct information about supported multi-monitor configurations with new Thinkpads? I'm trying to get Thinkpad P70 with M3000M + Workstation Dock (with 230W) to display different images on two external 4K monitors (Dell P2715Q), and so far without any success. Using DisplayPort 1.2 cables, no MST. Windows 10. All works fine if I'm only connecting one monitor. Laptop screen and the monitor happily get to 4K resolution @ 60Hz. However, as soon as I connect the other monitor, one of the monitors switches to 1920x1080, and 4K resolution isn't available to choose for that monitor. If resolution is set [email protected] both monitors work, but I want 60.  Tried everything. Switching between Discrete & Hybrid in BIOS, clean Windows 10 install (on a separate drive), different cables etc. Same result.  Looking for explanations, went to nVidia Control Panel,  and it reports that BOTH monitors are hooked up to the same DisplayPort (attached)?! Can P70 drive two external 4K monitors @ 60Hz at all?    
























topology.png ?66 KB

A:Thinkpad P70 + dock and 2 * 4K external monitors @...

Did p600 wrote:Is there any official and correct information about supported multi-monitor configurations with new Thinkpads? I'm trying to get Thinkpad P70 with M3000M + Workstation Dock (with 230W) to display different images on two external 4K monitors (Dell P2715Q), and so far without any success. Using DisplayPort 1.2 cables, no MST. Windows 10. All works fine if I'm only connecting one monitor. Laptop screen and the monitor happily get to 4K resolution @ 60Hz. However, as soon as I connect the other monitor, one of the monitors switches to 1920x1080, and 4K resolution isn't available to choose for that monitor. If resolution is set [email protected] both monitors work, but I want 60.  Tried everything. Switching between Discrete & Hybrid in BIOS, clean Windows 10 install (on a separate drive), different cables etc. Same result.  Looking for explanations, went to nVidia Control Panel,  and it reports that BOTH monitors are hooked up to the same DisplayPort (attached)?! Can P70 drive two external 4K monitors @ 60Hz at all?    Did you get any feedback regarding this?

Read other 9 answers
RELEVANCY SCORE 68

Hi all, I have a Yoga 260 and two external monitors.  It does not seem to matter how I connect them, USB, HDMI, whatever the thing with a square on one end and USB on the other, directly or through a splicer I can not get the Yoga to recognize the third screen individually (yoga has one monitor, plus 2 external monitors = 3). I go to display settings but it just will not recognize the third monitor at all unless I use HDMI out of the laptop in to a splicer then 2 HDMIs out and in that case I only get duplicates on the two external screens. Any suggestions about the best way to set up... as in "it worked for me when I connected USB to one monitor, then daisy chained that to a second one" or "it worked for me when I HDMI to one screen and USB to a second" etc... Thank you

Read other answers
RELEVANCY SCORE 68

I have a Thinkpad X1 Carbon 2 Gen that I want to set up 3 external monitors. I have 2 docks, Thinkpad USB 3.0 Ultra Dock and Thinkpad OneLink Pro Dock. Is it possible to run 3 external monitors?

Read other answers
RELEVANCY SCORE 68

Hi,I would like to connect my ThinkPad E450 to 2 external displays.I am aware that the laptop has only one HDMI port, and wondered maybe there is way to do so,perhaps with additional accessories?  Thank you

Read other answers
RELEVANCY SCORE 68

Laptop: Thinkpad T430s with Intel HD Graphics 4000 and Nvidia NVS 5200 M - 1 Mini Displayport, 1 VGAExternal Monitors (2): Dell U2415 - with Displayports and HDMI (no VGA or DVI ports on the monitors) Current setup:Monitor-1 (main display) is connected using Displayport - resolution 1920x1200Monitor-2 (extended display) is currently connected with HDMI using VGA to HDMI adapter that is attached to the VGA port on the laptop. However with this setup resolution on Monitor-2 is restricted to 1920x1080 I also have a docking station - Thinkpad Mini Dock Plus Series 3 - Type 4338.This has 1 VGA, 2 Displayports, 2 DVI-D ports. I tried the following options with 4338 but none of them worked.1. Connected both monitors using two Displayports on 4338. Only one of the monitors was recognized (1920x1200). Other monitor was not recognized at all.2. Connected monitor-1 to Displayport on 4338. Connected monitor-2 to mini Displayport on laptop. Only monitor-2 was recognized (1920x1200). How can I achieve 1920x1200 on both external monitors - with or without using the docking station 4338? I don't plan to use the laptop's LCD screen.  Thanks for the help. 

Read other answers
RELEVANCY SCORE 67.2

Hey guys,I've got new P50s (running W10 x64) with Quadro M5000M, and Ultra docking station for it. I want to use 4 external monitors in any configuration, just that they all work. I tried updating BIOS and Docking station, installed latest Intel and Nvidia graphics driver, power management driver.. everything.I get 4 monitors displayed in Windows display settings, but as soon as I turn on the fourth, one of the others goes dark. Somewhere I read about BIOS setting for Hybrid graphic, but I don't have such setting in BIOS. Any help would be great Thanks!

Read other answers
RELEVANCY SCORE 67.2

I've set up the laptop to work with 2 external ThinkVision L171 monitors, using Windows 7 Professional. One is connected via the VGA monitor port on the laptop; the other is connected via VGA to a Lenovo/DisplayLink USB 2.0 Port Replicator (model VDK8736 -- with drivers updated).

Both monitors are working well and available when the laptop lid is closed. The issue is that after the screen saver period completes, the laptop powers down completely. I'd like it to just shut off the screen and resume on mouse movement.

The laptop is used with external monitors when it's plugged in -- and the power settings are:
Balanced profile
Display turns off after 2 hours
Screensaver starts after 10 minutes
Computer goes to sleep - Never
Hard disk off - never
Internet Explorer: Javascript Timer Frequency - Maximum
Desktop background settings : available
Wireless Adapter Settings: Max Performance
Sleep - Never. Hybrid Sleep: Off Hibernate After: Never Allow Wake Timers: Disable
USB Selective Suspend: Disabled
Intel Graphics Power Plan: Balanced
Power Buttons & Lid: Lid closed - Do nothing; Power Button - Sleep; Sleep Button - Sleep
PCI Express - Moderate Power
Multimedia - When sharing media - prevent idling to sleep; When playing video - Optimize video quality

Does anyone know why this is happening and a way to prevent it?
Thanks!
 

A:Thinkpad 201X Laptop Shuts Down with 2 External Monitors

This is a tough one. Have you made any progress on this issue?
 

Read other 3 answers
RELEVANCY SCORE 67.2

Hi.  I'm hoping I can get this resolved on this forum.I just got my system and am trying to connect my 3 external monitors.    My setup is as follows:Monitor 1 - laptop screen - works.Monitor 2 - HDMI out to HDMI in - worksMonitor 3 - DP out to HDMI in via a DP-HDMI cable.  - worksMonitor 4 - DP ou to DVI in via a DP-DVI adapter - doesn't work. I can't figure out how to make this work.I also tried this setup:Monitor 1 - laptop screen - works.Monitor 2 - VGA out to VGA in - worksMonitor 3 - HDMI out to HDMI in - worksMonitor 4 - DP out to HDMI in via a DP-HDMI cable.  - doesn't work. Incidentally in this configuration, when I closed the laptop screen this monitor worked.  Also on a related note, the Nvidia Quadro P500  is sitting idle as the Intel UHD 620 is doing all the work.  How can I control this? Thanks for any suggestions. Sal

A:Thinkpad P52S Ultra Dock and 3 External Monitors

As stayed in PSREF, P52s supports up to three independent displays. Laptop's screen includes in this limit, meaning you can use two external displays at that time. When you close the lid, you can use three external displays. To use more, you'll need some sort of USB adapter to increase such a limit. Regarding other question, you can't disable Intel GPU - it's always active and it's always controls screen output. NVIDIA's dGPU can be configured to be used in selected applications, making them to work with higher performance. P52 and P72 for sure have an ability to disable Intel iGPU, giving the control of screen output to dGPU. Probably P1 and/or X1 Extreme have the same feature too.





------...

Read other 1 answers
RELEVANCY SCORE 66.8

I currently have a T430 which is an absolute beast and solid as a rock. However, it is a nightmare for external monitors. I have a Lenovo LEN LS2223wC monitor and a Lenovo LT1952p monitor that I would like to use as external monitors. Both monitors run on HD 4000. I run Windows 10 operating system.  I don't need the newest model. Just something solid and dependable. If it has the option of eventually doing three monitors that would just be icing on the cake (but not required).  Does anyone have any ideas for laptops that might fit these specs as well as docks to go with them?  Thanks

Read other answers
RELEVANCY SCORE 66.8

I have a ThinkPad S1 yoga bought in Dec 2013. I have being using the mini hdmi to work of 1 external 1080p monitor these last few years and it has worked fine. I now want to add a new second 1440 x 2560 along side my 1080 x 1920 monitor for a dual monitor set up. (Mostly for spreadsheets, emails, web browsing etc.) I do not mind if one of these duplicates my laptop screen. I was going to get the onelink dock to enable me to do this however I am not sure if it will work. I know the resolution with dual monitors running off the dock is limited at 1200p. What I now want to do is use the mini hdmi on my laptop for one monitor and the onelink dock for the other, however I want to be sure it will work before I go and buy the monitor and dock. Alternatively I could buy an USB 3.0 to hdmi adapted to run the 1080 monitor and a usb hub for the extra usb's I will need. (I think the dock will use less processing power and would be a slicker set up so I imagine it would be better?) You?re  help would be appreciated as I have read there can be issues trying to get higher resolution monitors to work. 

Read other answers
RELEVANCY SCORE 66.8

I have recently received an upgrade laptop at work. On my previous laptop (ThinkPad, unsure of model), I was able to connect one external display monitor directly to the VGA port on the laptop and an additional external diplay monitor to the ThinkPad Pro Dock station VGA port. I prefered to use these two screens with my laptop closed on the docking station, but could also open the laptop on the dock and have a third screen available. ISSUE: With my new ThinkPad (T440) there is no VGA port on the laptop. I have purchased a simple HDMI to VGA Converter Adapter - see link:https://www.amazon.ca/VicTsing-Gold-plated-Converter-Ultrabook-Devices-Black/dp/B016LVT51G/ref=sr_1_...   I am using the same ThinkPad Pro Dock station as with my previous laptop. With my new T440 I am able to work with my laptop open or closed on the docking station with one external display plugged into the docking station. I am also able to work with one external display plugged directly into my laptop using the VGA to HDMI converter adapter.  ISSUE 2: The laptop will not recognize when both screens are plugged in at the same time, but they each work when I have only one plugged in either to the dock or directly to the laptop. PLEASE HELP!! TIA

Read other answers
RELEVANCY SCORE 66

I have a brand new Lenovo ThinkPad L470 (win 10 pro) and a Lenovo Pro Dock. This configuration does not support two digital external monitors (don't get me started...) I want 2 digital external monitors.  Does anybody know if I will be able to support 2 external DisplayPort monitors if I purchase the Lenovo Ultra Dock?  thanks. 

Read other answers
RELEVANCY SCORE 66

I recently purchased the P52s and the Ultra Docking station.  I am dual booting Windows 10 Pro and Ubuntu 18.04.  I have dual 27" monitors connected to my Ultra docking station, as well as ethernet and power.  The Ultra connects to my P52s via USB-B Type -> USB.  Inititally all was well, but after a week or so,  my Ubuntu stopped seeing the dual monitors, even though the ethernet from Ultra continues to be picked up.   In Ubuntu the "display" only shows the built in laptop display and I cannot force it to detect external monitors. I have updated all the Lenovo drivers via the Windows updaters.  Previous threads seemed focused on other Lenovo products and didn't help me here.  

Read other answers
RELEVANCY SCORE 66

I would like to connect my ThinkPad X1 Yoga 1st Gen, running Windows 10 to 2 external AOC E2752VH monitors to extend my desktop over the 2 monitors.  Is it possible to use a 1 HDMI to 2 HDMI splitter to connect them?  Or is it better/possible to use a 1 mini DisplayPort to 2 HDMI splitter?

Read other answers
RELEVANCY SCORE 65.2

Hi, I am currently using the ThinkPad Mini Dock Plus Series 3 - 170W with 2 x 1920x1080 displays @ 60Hz a display. I am doing so by connecting one of the monitors to the DVI-D output on the docking station and 1 to a USB to HDMI converter (I was having issues with the VGA for some reason). I also use the laptop display as a third screen in the setup. What I am looking to do is purchase 3 x 2560x1440 displays and have the docking station power all 3 of these @ 60Hz. I understand that I can only use 2 display ports to do this so I intent to add a USB32DPPRO to achieve this, however my question is will they all run @ 60Hz. I have found this link which confirms I can run 2 displays at the resolution I'm after, but it does not mention anything about the refresh rate. https://pcsupport.lenovo.com/gb/en/solutions/migr-76767.  I'm just a little confisued as when you start looking at refresh rates on 4K for example, it says you can only run 1 screen @ 60Hz and if you add another screen the refresh rate drops to 30Hz for both. This is when used with the ThinkPad Workstation Dock 230W. More information here https://support.lenovo.com/gb/en/solutions/acc100247. If anybody could help demistify this that would be great! I am using a NVIDIA Quardo K1000M as my GPU and the Inter(R) HD Graphics 4000 for the onbaord graphics. It's probably worth nothing that if I can get all 3 monitors to run @ 60Hz and 2560x1440 I would not need to use the lap... Read more

Read other answers
RELEVANCY SCORE 65.2

Hi, I am currently using the ThinkPad Mini Dock Plus Series 3 - 170W with 2 x 1920x1080 displays @ 60Hz a display. I am doing so by connecting one of the monitors to the DVI-D output on the docking station and 1 to a USB to HDMI converter (I was having issues with the VGA for some reason). I also use the laptop display as a third screen in the setup. What I am looking to do is purchase 3 x 2560x1440 displays and have the docking station power all 3 of these @ 60Hz. I understand that I can only use 2 display ports to do this so I intent to add a USB32DPPRO to achieve this, however my question is will they all run @ 60Hz. I have found this link which confirms I can run 2 displays at the resolution I'm after, but it does not mention anything about the refresh rate. https://pcsupport.lenovo.com/gb/en/solutions/migr-76767.  I'm just a little confisued as when you start looking at refresh rates on 4K for example, it says you can only run 1 screen @ 60Hz and if you add another screen the refresh rate drops to 30Hz for both. This is when used with the ThinkPad Workstation Dock 230W. More information here https://support.lenovo.com/gb/en/solutions/acc100247. If anybody could help demistify this that would be great! I am using a NVIDIA Quardo K1000M as my GPU and the Inter(R) HD Graphics 4000 for the onbaord graphics. It's probably worth nothing that if I can get all 3 monitors to run @ 60Hz and 2560x1440 I would not need to use the laptop screen... Read more

Read other answers
RELEVANCY SCORE 65.2

Hi, I am currently using the ThinkPad Mini Dock Plus Series 3 - 170W with 2 x 1920x1080 displays @ 60Hz a display. I am doing so by connecting one of the monitors to the DVI-D output on the docking station and 1 to a USB to HDMI converter (I was having issues with the VGA for some reason). I also use the laptop display as a third screen in the setup. What I am looking to do is purchase 3 x 2560x1440 displays and have the docking station power all 3 of these @ 60Hz. I understand that I can only use 2 display ports to do this so I intent to add a USB32DPPRO to achieve this, however my question is will they all run @ 60Hz. I have found this link which confirms I can run 2 displays at the resolution I'm after, but it does not mention anything about the refresh rate. https://pcsupport.lenovo.com/gb/en/solutions/migr-76767.  I'm just a little confisued as when you start looking at refresh rates on 4K for example, it says you can only run 1 screen @ 60Hz and if you add another screen the refresh rate drops to 30Hz for both. This is when used with the ThinkPad Workstation Dock 230W. More information here https://support.lenovo.com/gb/en/solutions/acc100247. If anybody could help demistify this that would be great! I am using a NVIDIA Quardo K1000M as my GPU and the Inter(R) HD Graphics 4000 for the onbaord graphics. It's probably worth nothing that if I can get all 3 monitors to run @ 60Hz and 2560x1440 I would not need to use the lap... Read more

Read other answers
RELEVANCY SCORE 65.2

Hi, I am currently using the ThinkPad Mini Dock Plus Series 3 - 170W with 2 x 1920x1080 displays @ 60Hz a display. I am doing so by connecting one of the monitors to the DVI-D output on the docking station and 1 to a USB to HDMI converter (I was having issues with the VGA for some reason). I also use the laptop display as a third screen in the setup. What I am looking to do is purchase 3 x 2560x1440 displays and have the docking station power all 3 of these @ 60Hz. I understand that I can only use 2 display ports to do this so I intent to add a USB32DPPRO to achieve this, however my question is will they all run @ 60Hz. I have found this link which confirms I can run 2 displays at the resolution I'm after, but it does not mention anything about the refresh rate. https://pcsupport.lenovo.com/gb/en/solutions/migr-76767.  I'm just a little confisued as when you start looking at refresh rates on 4K for example, it says you can only run 1 screen @ 60Hz and if you add another screen the refresh rate drops to 30Hz for both. This is when used with the ThinkPad Workstation Dock 230W. More information here https://support.lenovo.com/gb/en/solutions/acc100247. If anybody could help demistify this that would be great! I am using a NVIDIA Quardo K1000M as my GPU and the Inter(R) HD Graphics 4000 for the onbaord graphics. It's probably worth nothing that if I can get all 3 monitors to run @ 60Hz and 2560x1440 I would not need to use the laptop screen... Read more

Read other answers
RELEVANCY SCORE 63.2

Hello I require to boot by USB my E550, but is not working. What I have to change o verify in the BIOS ? Thanks  

Read other answers
RELEVANCY SCORE 63.2

Back in summer I purchased a Thinkpad E550 from Lenovo spanish online shop, still today I don't have what I paid for.Before purchase, I tried confirming the availability of the TPM in the E550 models, after few calls, the only thing I was told is that if website says it has, it definetly has it. So I go on and purchase. On 07-09-2015 I receive confirmation for my purchase via email with all the details including TPM.Laptop was delivered with no TPM (not sure if any other component could be wrong, as I didn't investigate further). After several calls and effort, finally someone accepted that there was an error from Lenovo side and offered a replacement for another model, as E550 has no option of TPM or security chip (be careful when purchasing online using their configurator). They offered me a L540 model as replacement. I cannot consider this model because I don't like its touchpad configuration. I have been using thinkpad machines since IBM and its middle pointer mouse is one of the best features when accompanied by the button on top of touchpad. Anyway, the L540 model was worth around 300eur over the price that I paid for. I believe that that was their target of compensation and I went online and choose a model of the Yoga that was exactly 300 eur difference. They simply said no with no reason. They escalated the case and for my surprise, they accept a yoga as compensation, but they don't accept the configuration that I proposed, in stead they ... Read more

A:Thinkpad E550 TPM scam

Hola.Yo compré el pasado verano un E550 y venía con TPM 1.2Puedes comprobarlo en Administrador de dispositivos > Dispositivos de seguridad.Un saludo,Miguel



Hay 10 tipos de personas, las que saben binario y las que no.

Read other 1 answers