Over 1 million tech questions and answers.

USB 10/100 NIC with RJ45

Q: USB 10/100 NIC with RJ45

Does anyone have any experience using a USB 10/100 NIC with RJ45 port? I have found quite a few online, but just not sure of the reliability.

Running WinXP SP2

Would like to get any feed back from anyone that has used this type of NIC...

Thanks in advance...

RELEVANCY SCORE 200
Preferred Solution: USB 10/100 NIC with RJ45

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: USB 10/100 NIC with RJ45

I prefer not to use them. PCI network cards are the best. USB is a problematic interface, you'll see lots of posts here dealing with USB issues. Plus USB adds some CPU overheat that a good PCI network will reduce.

Read other 3 answers
RELEVANCY SCORE 39.2

Aloha,
I bought a printer with a female USB B and the other end calls for a USB male. The question that I have is that my Netgear 5 port switch is RJ45 female. I searched around and couldn't find a USB B male to a RJ45 male plug and was wondering why? Is it possible to make one or something like this is not compatable.

Mahalo,
doogdoog
 

A:RJ45 TO USB B Question

Read other 16 answers
RELEVANCY SCORE 39.2

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Turion(tm) 64 Mobile Technology ML-28, x86 Family 15 Model 36 Stepping 2
Processor Count: 1
RAM: 1150 Mb
Graphics Card: ATI RADEON XPRESS 200M, 128 Mb
Hard Drives: C: Total - 238464 MB, Free - 182597 MB;
Motherboard: Quanta, 3093
Antivirus: McAfee Anti-Virus and Anti-Spyware, Updated: Yes, On-Demand Scanner: Enabled

Okay, that's one Notebook. The other is a Gateway w34OUI running XP Media Center. Both are in great condition for their ages. Good for them. I really want to network the two with an RJ45 crossover cable, and all the instructions I've found on our illustrious internet tell me it's easy. HOWEVER, when I've only begun to follow those instructions (one list is from the God Microsoft itself), NONE OF ANY of the sets of instructions matches the steps offered on either one of these notebooks. The options do not correspond. The results do not correspond. The closest I get is a window that says I do not have access to such file sharing. These are MY computers, and have always been, and I am attempting to network using administrator ID logins on BOTH. What's the REAL way to network only two notebooks with an RJ45 crossover cable? Thanks in advance, I hope.
 

A:RJ45 Networking

What's the REAL way to network only two notebooks with an RJ45 crossover cable?Click to expand...

Connect one end of the cable to one notebook and the other end to the second notebook. Done; they are networked.

I assume that you really want to enable file and printer sharing; here is a "wizard" way ...

Run the Network Setup wizard (found in Control Panel of XP). Tell it each of your computers connects to the internet via "residential gateway" and that you want to enable file and printer sharing. Create a disk at the end only if you have a Windows PC other than XP or 2k Pro or newer.

Windows XP firewall (if SP2 or SP3) will be properly configured by the wizard (but make sure it is not set to “No Exceptions&#8221. You must uninstall or properly configure any 3rd party firewalls on each machine. Unique computer names and same workgroup, of course.

The Shared Documents folder is automatically shared. Any other folders (or drives) or printers you want to share, just right click on them and sharing ... . When sharing a printer, accept the offer to load other drivers if your other PCs have different Operating System(s).

When you first go into My Network Places there will be nothing there. The first time you click on 'View Workgroup computers' will probably result in great disappointment. It takes awhile (up to 15 minutes) before all the computers in the workgroup get up-to-date and accurate lists of the other computers. Often y... Read more

Read other 1 answers
RELEVANCY SCORE 39.2

I need a 30m Cat5e cable. It must be white and preferably with minimal writing on it. Any suggestions?
 

A:RJ45 Cable

Read other 16 answers
RELEVANCY SCORE 39.2

My first time. Hello... I think I have a simple question for now. I have DIRECWAY satellite dish with the reciever. I want to network to another floor but the DW dish uses a USB and the rounter uses RJ45...Is there such a thing to convert the usb? Thanks
 

A:network USB to RJ45

The simple answer is no. There is no easy way to connect a USB modem to anything but a PC. You could put a cheap PC in as a gateway and allow it to manage the network. I suggest Smoothwal, an excellent Linux based system that is turnkey and requires no Linux knowledge to setup and use.
 

Read other 1 answers
RELEVANCY SCORE 39.2

As a habit I try to avoid stringing cable without RJ45 connectors already installed but I recently installed a 110 ft. Cat 5e cable that require manually connected (female) RJ45's at each end. When I tested the cable my tester blinked from 1-8 on one end and 8-1 on the other end. I used A type configuration on both ends. Any expertise appreciated...

Wild Dingo
 

A:RJ45 connectors

With the order of continuity being different on each end, it isn't possible you used the same order on both ends. The problem is going to be figuring out which end is wrong. Get out your magnifying glass a look closely.

My guess is that you flipped the RJ45 connector when inserting wires into one of the ends. All of the instructions I've seen tell me to hold the retainer clip downward then gives me the order in which to insert the wires, left to right. You probably did it holding the retainer clip down on one end and up on the other.
 

Read other 1 answers
RELEVANCY SCORE 39.2

I would like to make a crossover cable. Should I crossover each of the pairs?

I would also appreciate any explanation on how the 4 wire pairs on a RJ45 cable are used.

Thank you.
 

A:RJ45 cable

Read other 6 answers
RELEVANCY SCORE 39.2

Hi guys,
Is is possible to get a cable RJ11 ( laptop 56k modem socket ) to RJ45 ( ISDN ) ???

If so where??
Can a 56k modem directly connect to an ISDN line ( obviously this is not an "ISDN" connection so the benefits of 64k and 128k are not going to be possible but, is the above feasible??
 

A:RJ11 to RJ45 ?? A to D

Read other 9 answers
RELEVANCY SCORE 39.2

My new Win10 laptop only has a Rj45 input. If I buy a Rj45 cable one end will probably fit into the Rj45 opening on the laptop but the other end will be too small to fit into the ethernet opening in the back of my modem/router. How would I get the Rj45 to fit my modem/router opening?
Is there some sort of an adapter that would allow the Rj45 cable to be plugged into the back of my modem/router with the larger opening?
 

A:Rj45 cable

Read other 16 answers
RELEVANCY SCORE 38.8

I have a computer I use for bittorrent and other file sharing programs. Legal, of course, I just share/download things like systm, twit, etc. I would really like to be able to turn off the internet connection to this computer at the router without needing to go to the computer, pause the downloads, etc. The computer Is in another room and I usually just want to check my email/search for something and turn the connection back on.

All I need is a coupler with a switch. I've searched the internet, but I cannot find anything like this. I have all the proper tools, cable, cable ends, etc. I installed the network in my house. I just need a simple on/off switch. A splitter with a switch would be fine too, I just wouldn't plug anything into the other port. I just can't find it. Please point me to someplace I can order something like this.

Thanks,
Doug
 

A:Cat5e/RJ45 ON/OFF Switch?

Read other 6 answers
RELEVANCY SCORE 38.8

Hi, I am new here but have a question if someone has an answer that would be much appreciated.
I am not very computer savvy but I will try and explain my question as best I can.
I will be going on vacation to the South Pacific on a tiny island and it's very expesnsive to call home. So i had an idea to get a Palm pilot to email my family who will be with our special needs daughter while we are gone, but when I checked into a connection they only have an RJ 45 plug for laptops and it is my understanding that the RJ 45 plug is to big for the palm pilots, is there such thing as an adapter or something that I can get to connect the palm pilot to that plug. Laptop to expensive for the time I need it. Thanks in advance for any help and sorry for the rambling.
Patty49
 

A:connecting PDA to RJ45 plug

Read other 7 answers
RELEVANCY SCORE 38.8

My Japanese friend got a LC900J laptop. He wants to join out LAN to use the internet. However, I can't find RJ45 connector on his computer and his windows is full of Japanese! Is this true that this laptop doesnt have a network card? Is there a way to connect this computer to the network using an USB adapter or something like that?

Thanks in advance!
 

A:Laptop without RJ45 connector

Read other 6 answers
RELEVANCY SCORE 38.8

Hi All, Ive just purchased an Envy notebook.  Just setting it up now.Connecting to the internet with WiFi is fine.  However, my work doesnt have WiFi, there is no RJ45 port on my Envy.How do I connect to the internet via a wired connection?  Is there an adaptor I need?  What type, and where to plug in? Regards, Rob Jarred

Read other answers
RELEVANCY SCORE 38.8

Hi,We have received several insidents with elitebook 840 G3 RJ 45 door damaging physically. Please someone help me to find the door & spring or chassis bottom to buy online. 

Read other answers
RELEVANCY SCORE 38.8

Hi,
Do you think that would work or we have any such convertors?
From my wireless connection I ppoe cable instead of phone cable, so the end is an RJ45 connector, my router input for wireless is RJ11, so if i convert that RJ45 to RJ11 and connect to the router.. that should be able to project the wireless connection right??

I can't find any RJ45 TO RJ11 convertors??

Thoughts

Cheers

A:Convert RJ45 to RJ11

think that won't work .. don't know.. the internet transmitter is wireless. so I have an antenna sitting on the window, connecteed to a none wireless router which got special inputs to receive and convert the radio signal to normal internet signal. Therefore I have a ppoe network cable that comes out which I connect to my computer as a RJ45
But I want to connect that network cable to a wireless router which has an input of RJ11 (PHONE JACK) input for internet. So i need I convertor to convert the RJ45 TO RJ11.

If I do that, the router will generate its own IP address and so there will be a conflict between both routers as both will try to generate an ip address, so if i put the second router which is a Thomson TG585 to have static ip address and convert the router to a repeater, it should be able to project that internet connection signal as wireless??

Who thinks thats possible??

cheers
Ash

Read other 11 answers
RELEVANCY SCORE 38.8

I have cat5e cable that has has rj45 connectors that I use for the telephone. This says it will only allow for one connection at a time but that was talking about data. Do you think it would allow two lines like a typical splitter. If not I need something cheap that would split some lines. Thanks.

http://www.monoprice.com/products/p...=10513&cs_id=1051304&p_id=1112&seq=1&format=2
 

A:RJ45 splitter question.

Read other 9 answers
RELEVANCY SCORE 38.8

Can someone confirm the speed of the native RJ45 interface on the Carbon X1?   10/100 or 1000?  TIA!

Read other answers
RELEVANCY SCORE 38.8

Hey everyone!

I am not sure if this is the right place to post this, but I feel like it relates to networking.

I work at a chemical company and we have a peace of lab equipment; a Varian CP-3800 GC - it is a Gas Chromatograph that connects to an old computer we have sitting running Windows XP SP3 and has a NIC card in it with a BNC connector. This peace of lab equipment runs over this BNC connection.

So what I am trying to do is to migrate to a new computer; put the NIC card in the new computer running Windows 7 x64. Here are my problems though.
The BNC card manufacture, Realtek has not made drivers for Windows 7. Model of the NIC is RTL8029AS
I tried a BNC to RJ45 converter, but it seems like either the GC does not see the connection or the converter is bad, but the RJ45 lights blink but the BNC lights show no activity.

Has anyone delt with something like this before? Any ideas?
 

A:Solved: BNC to RJ45 Converter

Read other 9 answers
RELEVANCY SCORE 38.8

I bought an RJ45 splitter from Cables To Go. I installed it on one of the out ports on a Linksys 4-port wireless router. I have all the other ports in use, and just wanted to hook in two computers that will never be in use at the same time. One of the out pots on the splitter works fine, the other will not allow a connection. I found a website that offers instructions for building a splitter and the wiring diagram from the website matches the diagram that appears on the back of the CtoG splitter. Also, a description of the use of the homemade splitter seems to be exactly what I am trying to do. I have considered two possibilities, one being that the CtoG splitter is just bad. I also got to thinking that the wired ports on the router may already be "split". Anyone have any suggestions?





 

A:Rj45 splitter problem?

hmm; you would be better off geting a cheap hub.

With the 'splitter' or a hub connected to a router, there's an issue that you may not be aware of - - IP address conflicts.

A major point of a router is to ensure each device gets a unique IP address assignment (using the DHCP feature). With a splitter (or hub), all connections see all the traffic so DHCP is ineffective. The only way to still use them is to have the connected devices
manually configured for all the TCP settings.
 

Read other 1 answers
RELEVANCY SCORE 38.8

I have a HP notebook running Windows 7 Pro that can access network shares and the Internet without issue over Wifi.

However, when I connect to the same network over wired ethernet (Wifi disabled), it can still access network shares, but no Internet.

Any ideas what might be the cause (other hardwired PCs can access both network shares and Internet normally) ?

Thanks.
 

A:Wifi: OK... RJ45: LAN, but no Internet

Read other 6 answers
RELEVANCY SCORE 38.8

My wireless router is downstairs in our living room, next to a telephone socket where it is connected (I believe the telephone connection is RJ12?). The telephone line extends up to a bedroom upstairs (cabled outside the house), where a telephone socket is presented in the bedroom.

The wireless signal doesn't reach the upstairs bedroom, I have tried Ethernet over power but the performance is average, so I had an idea. Why don't I run an Ethernet cable alongside the telephone cable, outside the house, between the two rooms? It makes sense to me. So my question is, can I buy a faceplate with an RJ12 and RJ45 socket presented, both downstairs and upstairs?

It should be noted that the socket downstairs has a test socket behind the faceplate, I am not sure if this would cause a problem? I'd rather take this route than have to install a separate RJ45 socket in each room if at all possible.

I hope this makes sense and if so, is it possible?

Thanks for reading!
 

A:RJ12 and RJ45 faceplate?

You can buy standard sized electrical faceplates that have one to six rectangular cutouts in them in them. The cutouts can accept snap in clips from the same manufacturer as the faceplate that contain various types of sockets. These sockets typically include RJ45, RJ11, Coaxial F, RCA Phono jacks, Phone jacks and spring loaded wire clips. There are also blank filler clips in case you are not putting jacks into all of the cutouts right away.

http://www.leviton.com/OA_HTML/ibeCCtpSctDspRte.jsp?section=11003&minisite=10051&language=US
http://www.leviton.com/OA_HTML/ibeCCtpSctDspRte.jsp?section=10231&minisite=10171

http://www.belkin.com/search/?q=keystone&x=0&y=0

I don't know where you are located but many hardware and home improvement stores (Home Depot, Lowes, Menards, etc.) in the USA carry at least one such product line.

FYI, A typical residential phone jack in the USA is RS11 with four out of six contact positions used. The two outside contact positions are left blank. An RS12 jack is the same size as an RS11 jack but uses all six positions.
 

Read other 1 answers
RELEVANCY SCORE 38.8

I have a home stereo reciever that will take a wireless usb signal and allow me to play mp3 music off my computer and into my home stereo.The problem I have is that the signal is only good for 30M and my rooms are too far apart.Is it possible to use the network wiring that I already have installed in the house(they are not currently being used)...buy the USB adaptors and wire directly into my home reciever???
Any help would be greatly appreciated.
 

A:USB to RJ45 Ethernet, 10/100Base-TX

Thats a good question, Infact, to what im reading you want this


Computer>USB to Ethernet > Ethernet cable > Ethernet to USB Reciever?

I dont see why that wouldnt work, but then again, I dont know that much about transmitting wireless signals and such.
 

Read other 4 answers
RELEVANCY SCORE 38.8

Is there really much difference in the ones for solid or stranded wire?

I have always used the same ones for either wire and never really noticed if they were for stranded or solid wire.

So, if I were to get the ones for standed wire, would it be terribly wrong to use them for solid wire too?
 

A:RJ45 Crimp Connectors

Read other 7 answers
RELEVANCY SCORE 38.8

I need CAT 5 color cording notes or picturs.if you have pls send me some note regarding cat 5 cabeling.my email address is [email protected]
 

A:CAT 5 color cording (RJ45)

http://www.netspec.com/helpdesk/wiredoc.html

Try this
 

Read other 1 answers
RELEVANCY SCORE 38.8

I have this "Terayon" Cable DSL modem with COX high speed,,
My question is that it offers a "RJ45" and "USB" setup whitch one one would supply the fastest interface?
on some downloads i get average speeds around 400Mbps/RJ45
BTW i have USB2.0

Thanks all
 

A:Cable DSL Modem,USB or RJ45?

Everything I've read indicates Ethernet is best for overall performance and reliability.....
 

Read other 7 answers
RELEVANCY SCORE 38.8

I notice that Ethernet RJ45 Cat5e cables vary considerably in price - with the most expensive costing 5 times the least expensive.

Is there any real benefit to purchasing an expensive Ethernet patch cable? And if there is what is the benefit?

TiA

T
 

A:Solved: Ethernet RJ45

Read other 8 answers
RELEVANCY SCORE 38.8

I have a Sony Vaio VGN-NS30 here. Connects perfectly to the internet with wireless.

Then when I try to connect by cable, nothing. It doesn't even recognise it has been inserted.
Windows Vista, newly installed.

Drivers fully up to date, when I ask it to troubleshoot, it says plug in the cable, done that, it doesn't recognise it.

What do we think? I'm pretty sure must be dead hardware. Anyone else?

Thanks very much.#
 

A:Dead RJ45 Port?

Read other 10 answers
RELEVANCY SCORE 38.8

Is it possible to extend a RJ45 CrossOver Cable, using an old serial cable?
- Yes both cables have the same amount of wires.

Because I'm having problems with my internet access, could I please get you to reply to:

[email protected]
Thanks.
 

A:RJ45 Cable Extension

see if this helps

http://www.netspec.com/helpdesk/wiredoc.html
Google search list

http://www.google.com/search?sourceid=navclient&q=RJ45+crossover+network+cabling

Couldn't e-mail this to you thru the forum cause you elected no e-mail be sent to you.
 

Read other 2 answers
RELEVANCY SCORE 38.8

At the office we want to show presentations to clients (made in word or power point). Instead of using a projector and a white screen we want to send it directly to a LCD or plasma TV or monitor. Can this be done using a RJ45 input? It would be quite difficult to send the signal using a VGA connection because the computer would be some 6 ft. from where the display would be hung on the wall. Thanks a lot!!
 

A:Rj45 lcd/plasma display

6ft. is nothing.
With out expensive hardware I would say no.
You could do this....
There are cheaper ones, but this is the only good one that comes to mind
http://www.newegg.com/Product/Product.aspx?Item=N82E16817791004
or something cheaper, but I cannot report on the quality.
http://www.newegg.com/Product/Product.aspx?Item=N82E16817406023
 

Read other 1 answers
RELEVANCY SCORE 38.8

Well, every time I just bump my cable it's get disconnected from the port.
I'm sure it's not cable. What can I do to get my RJ-45 port to be working normally? It does not even make that sound when cable is about to be plugged.

A:Bad contact RJ45 port

Have you checked the Clip on top of the cable?

Read other 9 answers
RELEVANCY SCORE 38.8

Just a simple question people,

Is RJ45 Cabling Waterproof and if not what do you suggest?


Thanks in advance,


Dan
 

A:Is RJ45 Cabling Waterproof?

The cable is but the connectors are not. You can purchase waterproof connectors.

http://metrix.net/metrix/products/ethernet
 

Read other 1 answers
RELEVANCY SCORE 38.4

I know the correct pinouts for 568A and 568B action, but in a recent install in a very harsh environment, (on a seismic boat alongside sheafs of really heavy cables carrying massive current pulses), the idea of the screen termination became a real issue.

So can someone put me straight, just how should the screen be connected at the connector to ensure a proper screening action?
 

A:How to wire in RJ45 connector screen

I'd probably run the cable(s) through a metal conduit or continuous metal braided sheath, grounded of course. In aircraft installations, that's how we run sensitive cables to avoid EMI issues, and the tests there are pretty severe.
 

Read other 3 answers
RELEVANCY SCORE 38.4

How does the tool less Keystone Jacks work? I can use these as wall jacks and I don't have to have a crimper? Are they any good?

Could I buy a "blank" patch panel and use these too without having to use the 110 tool? Are these a good idea for a small setup? Will they last?

I have searched the internet with little luck on how they are used.

Thanks

Jeff
 

A:Solved: What is a Tooless RJ45 Jack?

Read other 9 answers
RELEVANCY SCORE 38.4

I am running some cat5e cable to another room to run another computer and to run into my stereo also.
I will run two cables to a wall connector from my router. I have set the wall connector up with the T568A arrangement. Is that ok?
My question is how should I set up the cords running from the router? What arrangement and how should I set up the male end of the main cords running to the other room? Does this make sense? Thanks.
 

A:Question on making rj45 connectors

Read other 7 answers
RELEVANCY SCORE 38.4

Howdy Gents,
This could very well be a dumb question, but I'm an ignoramus when it comes to coaxial cabling. So, here goes:

I have a cable ISP. The data cable comes up through the basement into the cable modem upstairs in the family room, which is connected to a wireless router.

We recently finished the basement, and as I described in another thread, I want to wire a network switch down there. (I want to set up a small wired techbench without creating a subnet.)

So here's the plan:
Replace the existing cable walljack with an RJ45/CATV walljack like one of these. Then, run a cat5e from the router to the walljack down into the basement and into the switch.

Now, question:
Does it matter whether the jack specifies that it's for CATV (cable tv?) Or is all coaxial just coaxial?
 

A:CATV/RJ45 walljack question

That walljack should be fine. If you have a choice of quality, go for the "gold" standard as you want to reduce signal loss as much as possible.
 

Read other 1 answers
RELEVANCY SCORE 38.4

How can I connect my USB ADSL modem to a router which has only a RJ45 ethernet port?
 

A:USB ADSL Modem and RJ45 Router

You can't.
 

Read other 3 answers
RELEVANCY SCORE 38.4

All,

I live in a house that has a pre-wired network (model homes have a bunch of upgrades).

All of the telephone, network, and TV lines come into one closet, where the patch panels take in the outside lines and split them up.

I am looking to finally get my network up and working, but I have hit a snag.

I am trying to get my DSL modem to be shared by the network.

The telephone line patch panel has one output line remaining, and it is an RJ45. But the DSL modem only has a RJ11 input, which is industry standard.

From the modem, I can patch it into the distribution network.

The problem is that stupid RJ45 set up and the modem.

Most of the searches I have found really do not answer this question, so I come to you experts to hopefully lead me in the right direction.

Thanks!
 

A:RJ45 to RJ11 input to a DSL Modem

Read other 9 answers
RELEVANCY SCORE 38.4

hi all

i have a BT voyager modem which is USB only and a belkin wireless Cable/DSL Gateway Router which is RJ45 how can i get round this without getting another modem?

thx in advance

lee_1133
 

A:USB modem, RJ45 ADSL router! HELP!!!!!!

Read other 7 answers
RELEVANCY SCORE 38.4
A:Yoga 500 RJ45 Jack problem

Good day.Without more information about what specific problem(s) you're experiencing, it will be difficult for the community to assist you.Regards.

Read other 5 answers
RELEVANCY SCORE 38.4

heres what I'm trying to do on a single cat5 cable:

so where its circled I need some sort of jack to tap into the phone line. then at the end to have seperate rj45 and rj11 ports
 

A:RJ45 & RJ11 combo jacks?

nevermind, found it

http://www.dual-comm.com/RJ45_RJ11_Cable_Share.htm
 

Read other 2 answers
RELEVANCY SCORE 38.4

 i have a ENVY 15-AS027CL, does this computer have a RJ45 internet connection or is it witeless only.

A:I have a ENVY 15-AS027CL, does this computer have a RJ45 int...

HI; Looking at the specs page links below, there is no mention of an ethernet port. https://support.hp.com/us-en/product/hp-envy-15-as000-notebook-pc-touch/10862137/model/12206205/docu... http://www8.hp.com/h20195/v2/GetPDF.aspx/c05176355.pdf However, looking at the service manual, chapter 1, page 2, the service manual shows there is a 10/100 ethernet connection. http://h10032.www1.hp.com/ctg/Manual/c05128309 The driver page has ethernet drivers... https://support.hp.com/us-en/drivers/selfservice/hp-envy-15-as000-notebook-pc-touch/10862137/model/1... The user guide, chapter 2, page 7 shows the ethernet port is on the left side of the PC. http://h10032.www1.hp.com/ctg/Manual/c05125670

Read other 1 answers
RELEVANCY SCORE 38.4

ok i got a wd 1tb sata drive. i want to put it in an enclosure and connect it to my router via RJ-45 so i can put my familys movies on there as well as do regular back ups on all 6 of our computers... I cant seem to find a good enclosure to put my drive in. Secondly anyone have any suggestions for a good imaging software?

Thanks in advance, Matt
 

A:SATA enclosure with rj45 interface

imaging? as in HD image to new media? See Acronis True Image 11
 

Read other 7 answers
RELEVANCY SCORE 38.4

I am running some cat5e cable to another room to run another computer and to run into my stereo also.
I will run two cables to a wall connector from my router. I have set the wall connector up with the T568A arrangement. Is that ok?
My question is how should I set up the cords running from the router? What arrangement and how should I set up the male end of the main cords running to the other room? Does this make sense? Thanks.
 

A:Question on making rj45 connectors

Yes, my receiver has internet radio, and will update firmware via the internet.


I have a wall plate with two connectors and will run two cables to that and two from that wall plate. My other new whole house audio receiver from Russound uses the A terminations for the ends also so I guess that is what I will do for everything.

What exactly is a crossover cable? Thanks.
 

Read other 7 answers
RELEVANCY SCORE 38.4

Dear team,
I want to get 2 RJ45 ports on Optiplex, Precision, how to do that ?
Thanks

A:How to get 2 RJ45 port on Optiplex, Precision ?

You'll need to add a network card to the system -- if the model has a free PCIe slot,
www.dell.com/.../a9008619
If not, you'll need a USB to Ethernet adapter.
www.amazon.com/.../

Read other 1 answers
RELEVANCY SCORE 38.4

Hello,I am going to but the yoga 720 15.6 i5 FHD model and I noticed it doesnt have lan port or hdmi.If I buy an adaptor from type c to hdmi+lan will it work or I need something special from a certain company ? Another question: does the i5 fhd model wacom pen?I think I ll buy the Bamboo Smart for select tablets and 2-in-1  becasue its a lot cheaper in my country? will it work ?  thank you,Lior

Read other answers
RELEVANCY SCORE 38.4

In the last couple of days I can only connect to the internet if I hook up my router to the PC via a RJ45 cable.

Before this I would just turn th PC on and it would connect no problem. Now I get all lights on exccept the @ light. As soon as I connect the RJ45, it connects within seconds. I have tried to save the settings through the router page on Internet Explorer. It is quite an old Phillips router, I am wondering if it has just come to its natural end!

I am using Windows 7 32 bit.
 

A:Router will only connect via RJ45 cable

Have you checked your wireless adapter? It could have failed instead.
 

Read other 2 answers