Over 1 million tech questions and answers.

Help, please with startup error...

Q: Help, please with startup error...

Hello:
When I start the computer, I get this message
"ibmpmsvc.exe the exception privileged instruction (0xc0000096) occurred in the application at location 0x0012e78d click on ok to terminate the program click on cancel to debug the program".
How can this be fixed?
Thanks.

RELEVANCY SCORE 200
Preferred Solution: Help, please with startup error...

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: Help, please with startup error...

Hello drm1101 and welcome to the forum,

The process ibmpmsvc.exe is a power management driver for IBM laptops. It provides support for the use of four keys on the thinkpad keyboard with blue key tops - Fn, F3, F4 and F12 - which have specific functions to control the standby and hibernate buttons. It isn't required if you don't plan to go into standy or hibernate modes.

The only solution I have seen is to go tothis site and try the latest version of the power management driver:

http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-4GXPEG

Good luck,

-Matt

Read other 1 answers
RELEVANCY SCORE 39.2

so everything was fine when my laptop started to become very slow and i used to get the BSOD very often so i decided to recover the system to the initial state . i did that and everything was fine , then i updated the windows 7 service pack 1 and finished the installation and rebooted my computer , the start-up at least took half an hour at that time and the service pack 1 installation showed "not successful " i tried to again to update the service pack1 which showed 73.6mb - 892.6mb so i updated it again and again the same thing happened.

then i researched and found out that there is some problem with the windows service pack 1 and some daemon tools driver sptd.sys is also involved or something so i uninstalled daemon tools as well as windows 7 service pack 1 from control panel .

now the system is back to its normal speed once it starts up fully , and unless i switch it off there is no problem , but when i restart the system it takes at least half an hour to start up sometimes more than that , sometimes it never starts and i see the BSOD after the welcome screen with error 0x000000f4 and the physical memory dump fails with error 0xc0000010 .

i had also found something about minidump files which i didnt understand anything about , but i still tried to find the folder but i couldnt find the minidump folder in c:/windows/ so i figured maybe i didnt have a minidump folder.

any help would be really appreciated , and if you decide to help please do so thinki... Read more

A:BSOD on startup , error 0x000000f4 . startup takes half an hour

With the required information we can give you the best possible help.
http://www.sevenforums.com/crashes-d...tructions.html

Read other 7 answers
RELEVANCY SCORE 39.2

As the title suggests, my Acer Aspire has been running startup repair for over 20 hours following a BSOD yesterday. I'm not sure if it's worth the wait so maybe you all can shed some light. Yesterday I was stressfully trying to search for something (using Chrome) and the website I was on froze; admittedly I slammed the heels of my hands down on the laptop at that point. The site unfroze after less than 30 seconds, I continued using my laptop without incident, then let it hibernate for about an hour. Started up fine after that, and at that point I was beginning to rip a DVD (one that I owned; I just wanted the files on my computer) using a program that I've used successfully in the past, but the rip failed. So I began using VLC instead, and hadn't actually started ripping any files when my laptop froze. I had been trying to point to a file path for saving but hadn't saved anything. The laptop was completely unresponsive after several minutes, so I hit the power key to restart, which is when I got the BSOD. It flashed too quickly for me to read or remember anything other than the word KERNEL. I've been wracking my brain trying to remember if it said kernel error or kernel memory error or what.

After the BSOD I had the option to start normally or in startup repair; I hit "start windows normally" but it went to repair anyway. It was on the grey screen with the cursor but I thought it had frozen again, so I did another hard restart. No BSOD this time, but again the opti... Read more

A:BSOD on startup, unknown error, startup repair running too long

Bump...how can I tell if the startup repair is working?

Read other 2 answers
RELEVANCY SCORE 39.2

My laptop hasn't been in use for about a few weeks and all of a sudden, I am getting a Windows Error Recovery on Startup. I am given two options: Launch Startup Repair (recommended) and Start Windows Normally. Nothing happens when I try to restart Windows normally -- I only see a black screen. Upon selecting System Recovery, a teal screen pops up with "System Recovery Options" telling me to select a keyboard layout. Then it tells me to select my OS, but it comes up blank, telling me to load drivers for my hard disks. I stopped right there.

I am a little hesitant about using the System Recovery in fear of losing important files. If this is a possibility, I may try to backup my files using an alternate OS, like Ubuntu. Or are my files already long gone? Is this just a restore for important Windows files or a complete restore of Windows back to factory settings?

I have not installed any new software or devices. Running Windows Vista x64.

A:Windows Startup Error - System Recovery Launch Startup Repair

Definitely try to backup your files before doing anything else.

Read other 2 answers
RELEVANCY SCORE 39.2

Hi guys I was cleaning my laptop turned it on and it just wouldn't work so I turned it off and on again and it was giving me this error code saying my keyboard is not detected in start up. It then says there was a problem and shoots me to startup repair where it's just stuck not doing anything. My mouse and keyboard don't work, but I have a wireless mouse that I can use I can't access safe mode either because my keyboard doesn't work and I don't know if I can get a keyboard hooked up since my computer might not be able to recognize it. Sorry for the badly worded paragraph it's really late and I need to go to sleep. How can I solve this problem. Also startup time is really long ( usually 20 seconds) is now 5 min an doesn't even start up some times and I have no recovery disks or anything like that so im really confused what to do
Edit: A quick update, I started my computer in the morning and was not getting error 01010003, and my computer started perfectly fine however my keyboard still isn't working. I think it might be a driver problem, but I can't access Safe Mode... because my keyboard doesn't work. Is the only way of getting the key board to work getting a new keyboard and using that to diagnose the problem through safe mode or?

A:Error 0101003 Keyboard no detected, stuck on startup/startup repair

In this situation, you have to use another keyboard in order to test. I wish you will be luckier than me .... for me it turned out to be a motherboard failure My computer was working normally .... but no USB/PS2 ports were working.

Read other 1 answers
RELEVANCY SCORE 35.6

This message now appears on an otherwise excellent computer.

Cannot connect to wireless broadband (I'm doing this on my Equium P200D)

Any ideas. I've tried the Toshiba help to no avail.

A:Qosmio E10 CFSServ Listen Error & Recv InitConnect Error appears on startup

Hi

Someone wrote in this forum that the CFSServ is part of ConfigFree utility.
Remove ConfigFree application from the system and try to use and configure your WLan again or try to use the LAN connectivity!

Check it out

Read other 1 answers
RELEVANCY SCORE 35.6

Here's my story:

My sister's PC had been corrupted in lots of unnecessary programs and apps.
I deleted those craps. Windows Action Center then prompts me to update my windows, and I did.
PC restarted and POOF!!!, I am seem to be forever stuck in the Startup Repair Loop.
So I tried System Restore, but it's giving me the error code stated above (error 0x80070003).
I also tried System Image Recovery, and it's not also of help. Also, checking Hardware Options didn't help.
Lastly, I tried the Command Prompt option and it gives me nothing.

So how can I possible fix this error? ((

thanks in advance for those helpful respondents ))

A:Startup Repair Error (Forever Loop) Error Code 0x80070003

Hello Cath, and welcome to Seven Forums.

You might see if the tutorial below may be able to help with this.

Startup Repair Infinite Loop Recovery

Hope this helps,
Shawn

Read other 2 answers
RELEVANCY SCORE 35.6

Hi to all,

Around 5 days ago, some sort of error, cropped up while installation of Kaspersky Anti Virus on my laptop, and after that everytime, I turned the system on, I faced the blue screen error.

Then, i formatted my laptop and reinstalled Windows XP. It was running fine for two days. Suddenly, it started giving error "Logonui.exe application error" at startup displaying something similar to "The instruction at '0x0037149c' referenced memory" something.. It had to buttons - Cancel (for debugging) and Ok.. I pressed cancel/ok/close button. It always cropped up. Until after a series of pressing buttons, my log on screen came. After logging in, all my icons and taskbar gone. So, i opened Windows Task Manager and run "explorer.exe". After everything came up, Some Data Execution Prevention error cropped up. Whenever i tried clicking "Close Message", it always came up again with a separate window for the "Send Error Report to Microsoft" dialog box.

Whenever I connected to internet, the link under my Internet started blinking very fast. I even left it without any internet application open, but it still went on. I saw the properties window of my connection. It went on and on. And in return, everything went slow. Internet surfing and downloading. And one major problem occurred that, whenever I leave my internet open for a short while, it shows the blue screen of error and restarts.

I thought of formatting every drive ... Read more

A:Logonui.exe error at startup, dvd-rom not burning discs, blue screen error and more.

Hello and Welcome to TSF. I suspect you are infected with Virut.

Please go to: VirusTotalOn the page you'll find a Browse button.
Next to the Browse button you'll see a box to enter text.
Please copy/paste the following bolded text into the box:

e:\windows\explorer.exe

Then click the Send File button just below.
This will scan the file. Please be patient.
If you get a message saying File has already been analysed: click Reanalyse file now
Once scanned, copy and paste the URL from your browser address bar in your next reply.
Please repeat for the following files:

e:\windows\system32\userinit.exe
e:\windows\system32\svchost.exe
e:\windows\system32\spoolsv.exe

------------------------------------------------------

Read other 4 answers
RELEVANCY SCORE 35.6

This is a family member's laptop. It is a Dell Inspirion N4110 running Win 7 Home Premium x64
They gave it to me complaining that the shutdown button restarts the computer and will not actually shut it down.
So I checked its preferences, they were fine. I went into the registry and changed the value from 1 to 0. That didn't work. (I changed it back)

I noticed on start up there is an error (it still pops up) that says there was a problem starting c:\users\blah\AppData\Roaming\homsp.dll The specified module could not be found.

The I decided to run a virus scan. Their McAfee had expired so I uninstalled it along with some odd software from a company called SysTweak or something and installed AVG and Malware Bytes. Those full scans came back clean except AVG found something and removed it but it wasn't of any significance to this issue.

I decided to check Windows Update, it wouldn't run. So I tried to restart it in Services and it wasn't there. After some piddling I found a program that supposedly fixed the problem for you. It was called Fix WU. I got it Softpedia. After running it the Windows Update service was back. I was able to install some updates and thought all was well. Then there were more updates. I tried to install them and got an error 80246008.

So I then realized BITS wasn't listed in the Services, either. I found a download (? [SOLUTION] Windows Update and BITS services missing) that contained reg files for Windows 7, installed it, ran the bits file and then res... Read more

A:Update error 80246008, Restart on Shutdown, dll startup error

I'm in no way a expert on such things but I did notice something you found.
SysTweak

Their is no way of knowing all the things a program like that has done. If I had to repair this computer I would start with a repair install.

Give this a good read.

Repair Install

Then I would install MSE for a anti virus and use the built in Windows Firewall.

http://windows.microsoft.com/en-us/w...tials-download

Little note: If you didn't use McAfee's online removal tool their could of been left overs of McAfee on the computer when you installed AVG and that would be just more problems.
Any anti virus program you remove I recommend using their own removal tool found online.

Read other 3 answers
RELEVANCY SCORE 35.2

Hey Everyone,

Please help! I recently let my roomate use my desktop - and now my computer seems to be dying.

Upon startup I get the following 3 errors:

RUNDLL: Error loading C:\WINDOWS\ociganis.dll
RUNDLL: Error loading C:\WINDOWS\dshtpras.dll
hpqthb08.exe - Common Language Runtime Debugging Services: Application has generated an exception that could not be handled. Process id=0xfa0 (4000), Thread id=0xfa4 (4004). Click OK to terminate the application. Click CANCEL to debug the application.

ALSO - Most importantly... my internet is not working! I've gone into the settings and changed everything back to default, but still no luck.

Any help?

A:RUNDLL Error & hpqthb08.exe Error at startup - No internet

welcome! I know that hp one is from hp imaging programs that install with a scanner or camera or something. Try uninstalling that and let us know what happens.

Read other 3 answers
RELEVANCY SCORE 35.2

Hello,

I have read a lot of helpful information on this site, so for that I want to say thanks!

I am struggling to fix the error that I get upon startup on my Toshiba Satellite L655 which Reads"

RunDLL
Error in C:\Users\(my name)\AppData\Roaming\actxprxy1.dll
Missing entry:Igwq

I just realized that this isn't referencing actxprxy.dll - it has a "1" stuck in there which is raising a red flag for me and may be why all my google searches come up empty.

I have updated windows, which I didn't update currently because I keep it up to date, I have run Microsoft Malicious Software Removal Tool which found nothing, I have run Malwarebytes which found nothing I have of course run my current anti-virus, malware, registry cleaner software and it says all is good too. Nothing is running poorly on my computer but I am starting to think that there was something that happened and my computer was able to remove it but maybe not all of it or there are damaged files from it? I am not super computer saavy but I do pretty well and can definately can follow good directions. I would really appreciate any help with this that anyone can provide!

Thanks,
Gaby

A:Error upon Startup, "Error in C:\Users\....\actxprxy1.dll

Hello,

Is there a actxprxy.dll present?

Is there an error in your event logs? When does the error display?
Dave

Read other 9 answers
RELEVANCY SCORE 35.2

  
Quote: Originally Posted by Kaktussoft


Try to start clean boot Troubleshoot Application Conflicts by Performing a Clean Startup
Same problem?


I'm having same problem, but this solution didn't work for me.

VSS is autostart and running.

I've been running Macrium Reflect (free) for months on this system with no problem, but seem to remember it updated a few days ago.

Any other ideas?

BTW, I notice this thread is marked 'solved' so should I open a new thread?

Thanks, J.

A:Macrium Reflect error BEX64 (Win error?) on MR startup

Confused.

This problem got solve with update of macrium reflect few days after this problem started. But again few days ago got other next update from macrium and now same problem happen again.

Think I'll change to Comodo backup, its free too.

Read other 1 answers
RELEVANCY SCORE 35.2

After installing win7 64bit home premium I cannot rum Macrium Reflect (free).
On startup of MR I get this msg:

Problem signature:
Problem Event Name: BEX64
Application Name: Reflect.exe
Application Version: 5.3.7109.0
Application Timestamp: 53ccfa37
Fault Module Name: StackHash_511e
Fault Module Version: 0.0.0.0
Fault Module Timestamp: 00000000
Exception Offset: 0000000171af0000
Exception Code: c0000005
Exception Data: 0000000000000008
OS Version: 6.1.7601.2.1.0.768.3
Locale ID: 1033
Additional Information 1: 511e
Additional Information 2: 511ea21ce31ca5b9d66e08a72b3f15b4
Additional Information 3: 41bf
Additional Information 4: 41bf1755a6f43c010a107e904eb3c9eb

Searching MR forum the only lead I got was Win VSS. (MR won't let free users register for forums)
VSS is autostart and running. I re-registered VSS componentsand that didn't work.
Any ideas or help?
Thanks,
Frank

A:Macrium Reflect error BEX64 (Win error?) on MR startup

Try to start clean boot Troubleshoot Application Conflicts by Performing a Clean Startup
Same problem?

Read other 3 answers
RELEVANCY SCORE 35.2

The rest fo the error message says- "Failed to read configuration file. Please contact system administrator"
I have just R and R'd Firefox and I'm still getting this error message. It won't run now and now I see just how horrible IE is in XP,since I'm forced to use it now....sob
Please Help!!

A:Firefox won't startup-Error message says "Configuration error"

Only an idea!!!!  Not sure but it may be the newer FF may not run well on XP, you could experiment by down loading and older version.
 
Just checked I may be right check the link below!
 
https://support.mozilla.org/en-US/kb/firefox-no-longer-works-some-versions-windows-xp

Read other 7 answers
RELEVANCY SCORE 35.2

I am having problems with my computer starting in safe mode all the time. I have tried going into msdos and putting in boot 0 and changing read only stuff back again but to no avail.(ie) brindle 10-20-03.. help! I must have changed something some where eh? Also I keep getting these error mess. more and more. I have aim and just recently it started giving me mss about that and if I don't catch the pop up window that comes with aim, in time then my puter freezes on me and I have to shut down and go in again.. Also....... I am still getting the start up mess of a file is missing and to delete and uninstall etc etc then it has Mcaffee system ini etc etc ,...Well I went and deleted all Mcaffee stuff as recomemned by styxx and am still getting this at start up? HELP I am ready to throw this out the window... no pun intended! My husband thinks I have ruined his computer and is still giving me dirty looks..... I have windows 98se. 254 mgbytes memory, I think,and have dsl...Help
 

A:safe mode and startup error and error messages

Have you tried going into set-up and resetting all controls to "default setting"?

You're computer is most likely going into default mode because there is something else wrong with it.

You most likely haven't ruined it........jus need to take this one step at a time

What were the first error messages you were getting?

What happened the first time your computer started in safe mode all by itself?
 

Read other 1 answers
RELEVANCY SCORE 34.4

When i startup my computer an error appears

(Name Of Box)MOM.EXE - .NET Framework Initialization Error
(Red circle with X) Unable to find a version of the runtime to run this application.
[ OK ] Button

The picture on the task bar is the ATI logo and says ATI. I looked up MOM.exe and knew it has something to do with ATI, i have tried uninstalling and reinstalling my ATI drivers, didnt fix the problem.

I was having a problem before where I had a similar error at startup. The name of the box was MOM.EXE, and it said it couldnt run the problem if i remember right.

Im both cases i can click the OK button and the error doesnt come up again until i restart my computer.

I am using Windows XP Home.

Thanks in advance for the help.

A:At Startup Error: Mom.exe - .net Framework Initialization Error

This error may be a result of the .NET Framework either not being installed or the installation is corrupt. Go Start > Control Panel > Add/Remove Programs and make sure the Show Updates box at the top is checked. Then search for an entry called:Microsoft .NET Framework 2.0If it is there remove it (don't worry if it is not there). Then go to this site and download a fresh copy of it. Install it, reboot and then see if your problem has been solved.

Read other 16 answers
RELEVANCY SCORE 34.4

Hi. I am currently using windows xp professional and on startup, i get these two annoying messages:

RUNDLL:
Error loading C:\WINDOWS\xccdf16_080906a.dll
The specified module cannot be found

RUNDLL:
Error loading C:\WINDOWS\xccdf16_080906a.dll
The specified module cannot be found

These messages are very annoying and i would like to get rid of them.
Here is my hijackthis log:

Logfile of HijackThis v1.99.1
Scan saved at 12:06:33 PM, on 10/Sep/2008
Platform: Windows XP SP3 (WinNT 5.01.2600)
MSIE: Internet Explorer v7.00 (7.00.6000.16705)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\Common Files\Acronis\Schedule2\schedul2.exe
C:\Program Files\Common Files\Apple\Mobile Device Support\bin\AppleMobileDeviceService.exe
C:\PROGRA~1\AVG\AVG8\avgwdsvc.exe
C:\Program Files\IVT Corporation\BlueSoleil\BTNtService.exe
C:\Program Files\Nero\Nero8\Nero BackItUp\NBService.exe
C:\PROGRA~1\AVG\AVG8\avgam.exe
C:\PROGRA~1\AVG\AVG8\avgrsx.exe
C:\WINDOWS\system32\svchost.exe
C:\Program Files\Common Files\Acronis\Fomatik\TrueImageTryStartService.exe
C:\PROGRA~1\AVG\AVG8\avgnsx.exe
C:\Program Files\VMware\VMware Workstation\vmware-authd.exe
C:\Program Files\Common Files\VMware\VMware Virtual Image Editing\vmount2.exe
C:\WINDOWS\system32\vmnat.exe
C:\WINDOWS\system32... Read more

A:RUNDLL Error on startup, error loading

Read other 15 answers
RELEVANCY SCORE 33.2

Windows vista enterprise edition on start up shows an error rundll32.exe,
error message saying "windows cannot access the specified device,path,or file. You may not have the appropriate permissions to access the item

A:Rundll32.exe error on startup error message saying "windows cannot access the specified device,path,or file. You may not have the appropriate permissions to access the item

Hi,
Please click start, type msconfig and press Enter.
Under the startup tab, find the item reads like RUNDLL32.EXE, c:\windows\system32\xxx.dll and uncheck it.
Save the change and restart.
Or you can modify the registry by loading registry editor.
Navigate to HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion\Run
Deleted the RUNDLL32.EXE, c:\windows\system32\xxx.dll
Regards,Please remember to click ?Mark as Answer? on the post that helps you, and to click ?Unmark as Answer? if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ?

Read other 3 answers
RELEVANCY SCORE 33.2

When the machine would normally be going to the Windows startup screen, instead it shows two lines of print separated by a blank line, white print on a black screen:

Boot error: 0-00


Select partition to boot, 0-3:_

the underline at the end of the second line is a flashing cursor. It remains with this showing until I enter any character, and hit 'RETURN', whereupon the normal boot process resumes. It doesn't matter if I enter one of the four requested digits or something else, any character will do. While this seems simple enough, it worries me - I don't like partition problems, especially since I'v seen Windows 7 repeatedly simultaneously convert normal partitions on up to three drives at once into completely unreadable garbage that no partitioning software can read. While there seems to be no consequence from this behavior, I've become very skittish since witnessing what Win 7 can so completely foul up. I've had this boot error before, and the only thing that removed it was completely repartitioning and reformatting the drive involved. Does any body recognise this? I've been working on and in computer systems since they were called 'numerical calculators', back in the fifties, and I've never seen this until two years ago. Both times I've seen this start, it's begun at startup from a cold boot, after a long series of drive changes, otherwise I know of no other common factor. I know I'm getting old and stodgy, but I really don't like this. The error stays with the driv... Read more

A:Startup error 'Boot error:0-00'

Just out of curiosity have you run a malware scan with malwarebytes?

Please download the free version of Malwarebytes.
Update it immediately.
Do a full system scan
Let us know the results at the end.

Malwarebytes : Download free malware, virus and spyware tools to get your computer back in shape!

Read other 4 answers
RELEVANCY SCORE 32.8

Today I got my new laptop and decided to dual boot Ubuntu and Windows 7 on it. After several hours of partitioning and researching, I ran into many issues. Eventually I decided to boot Ubuntu from a USB drive, open up Gparted, and delete any and all Linux partitions while expanding the size of the Windows partition back to normal.

Unfortunately, in the process, I must have made an error, because now upon startup I get the "bootmgr is missing" error. I don't have a recovery CD nor does my laptop have a CD drive, so that's out of the question, but I know for a fact my Hard Drive has a recovery partition on it. I want to restore my computer back to normal, keeping my old files if necessary. However, since I just got the computer today, I clearly don't have anything on there I can't afford to lose, so if I must do a factory reset I will.

A:"Bootmgr is missing" error upon startup, caused by human error

Welcome to the forum,

Sounds like quite a mess, you can try Bootmgr is missing - Fix

Since you don't have an optical drive you can USB Windows 7 Installation Key Drive - Create

Since you need a repair disc or an install disc to do that you'll want to create one

With the installer ISO for your licensed version here Official Windows 7 SP1 ISO from Digital River ? My Digital Life



You may just want to get a superior clean reinstall using the COA key on your computer,

Clean Reinstall - Factory OEM Windows 7

Read other 7 answers
RELEVANCY SCORE 32

Ok so i was playing all normal like on my computer and i have a weird freezing problem where the whole screen locks except my mouse so i restarted and it always goes back to normal but this time it said my application are not working so i restarted it said it one more time and then when i restarted one more time it put me into startup repair iv been in the repair for four hours. Apperently its trying to repair my disk error but its taking over four hours. I have a windows vista running windows 7 premium 32 bit hope to hear back from u guys soon! Thanks!

A:Help on a startup error please

Will you please make some points clear ?
1.




Quote:
I have a windows vista running windows 7 premium 32 bit


Does it mean that you have upgraded from vista ?
2. Is yours a laptop or a desktop ?
4. What is the volume of of your RAM ?
5. Have you tried Startup Repair as described in this tutorial ? If no, run it at least 3 times with restarts after each single run.

Read other 9 answers
RELEVANCY SCORE 32

When I log in, I get an error:
"Error loading C:\program files\wildtangentApps\CDA\cdaEngine0400.dll
The specified module could nor be found"

I've used the RUN:MSCONFIG command and removed the startup item from the list, but now when it starts up, it is in "Selective startup" mode, is there any way i can remove the startup item from the list without it being in selective startup? THere is no "wildtangentapps" folder in Program Files, btw.
 

A:Startup Error

Read other 6 answers
RELEVANCY SCORE 32

I am posting the completed aswmbr scan as requested. Thanks.
aswMBR version 0.9.9.1665 Copyright© 2011 AVAST Software
Run date: 2012-08-12 19:37:21
-----------------------------
19:37:21.332 OS Version: Windows 6.0.6002 Service Pack 2
19:37:21.332 Number of processors: 2 586 0xF0D
19:37:21.332 ComputerName: STEPHEN-PC UserName: Stephen
19:37:39.111 Initialize success
19:38:51.005 AVAST engine defs: 12081201
19:39:19.824 Disk 0 (boot) \Device\Harddisk0\DR0 -> \Device\Ide\IdeDeviceP0T0L0-0
19:39:19.825 Disk 0 Vendor: WDC_WD4000AAJS-65TKA0 12.01C01 Size: 381554MB BusType: 3
19:39:19.832 Disk 0 MBR read successfully
19:39:19.833 Disk 0 MBR scan
19:39:19.867 Disk 0 unknown MBR code
19:39:19.868 Disk 0 Partition 1 80 (A) 07 HPFS/NTFS NTFS 372475 MB offset 63
19:39:19.900 Disk 0 Partition 2 00 07 HPFS/NTFS NTFS 9075 MB offset 762830460
19:39:19.908 Disk 0 scanning sectors +781417665
19:39:19.971 Disk 0 scanning C:\Windows\system32\drivers
19:39:35.513 Service scanning
19:40:03.914 Modules scanning
19:40:30.344 Disk 0 trace - called modules:
19:40:30.356 ntkrnlpa.exe CLASSPNP.SYS disk.sys acpi.sys hal.dll ataport.SYS pciide.sys PCIIDEX.SYS atapi.sys
19:40:30.359 1 nt!IofCallDriver -> \Device\Harddisk0\DR0[0x85f98a78]
19:40:30.362 3 CLASSPNP.SYS[8a7a68b3] -> nt!IofCallDriver -> [0x84d8e408]
19:40:30.366 5 acpi.... Read more

A:Startup error

Create a restore point before modifying registry entriesPress Windows+R key and typeregedit and click okBrowse to HKEY_CURRENT_USER\Software\Microsoft\Windows NT\CurrentVersion\WindowsOn right pane you should find LOAD or RUN key with this value C:users/stephen/appdata/local/temp/{73984~1.exe ,delete it.If you get access denied error go to HKEY_CURRENT_USER\Software\Microsoft\Windows NT\CurrentVersion\Windowsright click on Windows key Click on permissionsCLick on EveryoneUnder permissions ,select FULL CONTROL and click ok,now you should be able to delete the LOAD keyPlease run mbam again and post the new log

Read other 10 answers
RELEVANCY SCORE 32

Hello,

Each time I start my computer, I receive a message stating:

DLL C:\WINDOWS\System32/2ndsrch.dll is not a valid windows image.

I ran adaware and spybot (deleted everything in red). Any attempt to install Spyware Blaster failed because:

C:WINDOWS\System32\MSINET.OCX error occured while trying to replace existing file DeleteFile failed;code 32. It is being used by another process.

I ran HiJack This

Logfile of HijackThis v1.97.7
Scan saved at 12:09:05 PM, on 1/4/2004
Platform: Windows XP SP1 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP1 (6.00.2800.1106)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\LEXBCES.EXE
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\system32\LEXPPS.EXE
C:\Program Files\McAfee\McAfee VirusScan\Avsynmgr.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\wanmpsvc.exe
C:\Program Files\McAfee\McAfee VirusScan\VsStat.exe
C:\Program Files\McAfee\McAfee VirusScan\Vshwin32.exe
C:\Program Files\McAfee\McAfee Firewall\CPD.EXE
C:\Program Files\Common Files\Network Associates\McShield\Mcshield.exe
C:\Program Files\McAfee\McAfee VirusScan\Avconsol.exe
C:\WINDOWS\Explorer.EXE
C:\Program Files\McAfee\McAfee Firewall\CPDCLNT.EXE
C:\WINDOWS\System32\hkcmd.exe
C:\WINDOWS\AStart.exe
C:\Program Files\McAfee\McAfee VirusScan\alogserv.exe
C:\Program Files\Roxio\Easy CD Creator 6\DragToDi... Read more

A:error on startup

Read other 11 answers
RELEVANCY SCORE 32

when i start my computer, there comes an error. that is-- PXE- network boot cancelled by keystroke ERROR: no boot device has been detected or the disk failed.please tell me any solution for my problem

Read other answers
RELEVANCY SCORE 32

Everytime I swich Computer on the following message comes up:

"Error loading C:\WINDOWS\Downloaded Program Files\bridge.dll . The specified module cannot be found."

How can I get rid of this message so it doesn't pop up every time I start computer?
 

A:Startup Error

Read other 8 answers
RELEVANCY SCORE 32

when ever i turn my computer on i get this message...

"Invalid Backweb application id 1940576"

i remenber disabling "Backweb" from my startup...but how do i get it off my computer..so this problem doesnt happen anymore?
 

A:Run Error at startup...says...this...

I remember reading about backweb.... Essentially its spyware. Try running adaware

http://www.liutilities.com/products/wintaskspro/processlibrary/backWeb/
 

Read other 1 answers
RELEVANCY SCORE 32

When i started my system just now it took 3 attempts before it actually started without this error -

It said on the startup screen USB device over current status detected will switch off in 15 seconds?

It keeps happening now!

ASUS Z87-A

Windows 7

Read other answers
RELEVANCY SCORE 32

When I try to start up the computer, everything works until after the XP logo loading screen. After that, there's a long long black screen that eventually turns into a blue error screen that says "driver_irql_not_less_or_equal". I have no clue whats going on. All I did yesterday was install battlefield 2 and spill a bit of water on my keyboard. Could either of those things have caused this?

Any help is extremely appreciated, I just got FEAR and want to play it quite badly.
 

A:XP Startup Error

Read other 16 answers
RELEVANCY SCORE 32

Everytime I start my computer I get an error that says, A problem with your harddrive has been detected. Consult troubleshooting of your user manual. Push any key to continue, and my compter seems ok. I got rid of spyguard and got my home page back, and my computer was restarting, but so far it hasn't restarted. So I will just ask about this problem for now. I can't find anything in my manual about this error, or anything else about it. Anyone have any idea's?
 

A:Error on Startup

Read other 16 answers
RELEVANCY SCORE 32

I am having trouble removing an error i receive on startup. The message reads as follows:
"Error loading C:\PROGRA~2\Kodak\EasyShareSetup\$REGIS~1\Registation_7.4.20.2.sxt The specified module could not be found".

I had a similar problem on my old computer which i sorted easily as i used msconfig to remove useless files on startup. This one however i cannot find on Vista OS and have had no luck searching through regedit. I have also tried programs such as Register Cleaner for Vista and Ad-aware 2007. As far as i know i cannot see what is trying to open this non-existent file relating to Kodak EasyShare which i uninstalled a few days ago. Please help.
 

A:run.dll error on startup

Read other 6 answers
RELEVANCY SCORE 32

Windows XP SP2

As far as I know, my client tells me that nothing has changed on the computer, nothing installed/uninstalled...

I already ran Spybot, Ad-Aware, and Hijack This! Can't find anything wrong

Any ideas?

Rafster
 

A:DNS Error comes up at startup

This May Help

http://discuss.pcmag.com/forums/thread/1004378319.aspx
 

Read other 1 answers
RELEVANCY SCORE 32

I have Windows XP and when I start my computer, a box opens up which looks just like the Internet Explorer error box and reads:

"hole has encountered a problem and needs to close. We are sorry for the incovenience."

I read the file that it says will also be sent in the error report:

C:\DOCUME~1\username\LOCALS~1\Temp\WER1.tmp.dir00\appcompat.txt

It doesn't seem that anything happens besides this box opening. I'm able to browse the Internet using Internet Explorer.

I've ran my McAfee virus scan and spybot program and neither have solved the problem. Any ideas?

Thanks.
 

A:Error at Startup

Read other 10 answers
RELEVANCY SCORE 32

Ok, everytime the computer is restarted I get this message...

Could not load or run C:\Users\Cody\AppData\Local\Temp\wvutr.exe specified in the registry. Make sure the file exists on your computer or remove the reference to it in the registry.

How do I solve that problem? Most of the time a lot of new tabs open up when accessing the internet and Norton antivirus or google toolbar isn't stopping it. The computer also occasionally makes all the icons and the taskbar at the bottom disappear. This is a brand new computer Inspiron 531. One more thing, as I m typing this I usually have to go back and fix mistakes because the keyboard is not processing all the key presses. Thanks a bunch to anyone who can help!!
 

A:Error on startup plus more

Read other 7 answers
RELEVANCY SCORE 32

Awhile ago MBAM detected something and got rid of it. Now during start up this message pops up...

There was a problem starting
C:\Users\Len\AppData\Roaming\acccore\sp.DLL
The specified module could not be found.

I figure it's something left behind from what ever was infecting my computer. Any help on how to rid of it? Thanks.

A:sp.DLL error on startup

DownloadTDSSkillerLaunch it.Click on change parameters-Select TDLFS file systemClick on "Scan".Please post the LOG report(log file should be in your C drive) Do not change the default options on scan resultsDownloadaswMBRLaunch it, allow it to download latest Avast! virus definitionsClick the "Scan" button to start scan.After scan finishes,click on Save logPost the log results here.If you get crashes in normal mode,run it in safemode with networkingDownloadESET online scannerInstall itClick on START,it should download the virus definitionsWhen scan gets completed,click on LIST of found threatsExport the list to desktop,copy the contents of the text file in your reply

Read other 11 answers
RELEVANCY SCORE 32

Ok, I had Window Xp and Ubuntu. I wanted to get rid of ubuntu, so in windows XP, under computer management and disk management, I right clicked and deleted the partition. Then I created a new logical drive. However, when I restarted my computer, it says: "Verifying DMI Pool Data.............. GRUB Loading stage1.5. GRUB Loading, please wait... Error 17" And now I can't start up Windows XP anymore!

Anything I can do?

A:Startup error 17

Hi

Deleting the Ubuntu partition deleted the GRUB bootloader, which gives error 17. To fix it, you need to rewrite the MBR so that it no longer contains GRUB.

You will need an XP CD to do this. Boot from the CD, and at the first screen, press R to enter recovery console.

It will then ask you which install you want to log on to. Type in 1 and press enter. You may then need to enter the administrator password (Blank by default)

Now type in fixmbr and press enter. It will give you a warning about a possible loss of data, press Y to continue.

Then type exit to restart the PC.

Hope this helps you

Read other 4 answers
RELEVANCY SCORE 32

hi

everytime when my computer starts up i keep getting an error is there something i can do to fix it? Screenshot provided


 

A:GUI.exe error on startup

Do you have a Gigabyte motherboard?
 

Read other 4 answers
RELEVANCY SCORE 32

the computer is 1.6 gb with 512 mb ram 60 gb hard drive and 865intel mb
on bootup it gives me this error pri master hard drive disk:s.m.a.r.t. status BAD, backup and replace (press f4) to resume

after that i can load some operating programs win 98 one time the recovery another the last time it wouldn't get past memory, but later after os is on i get error messages about not enough memory available.

is it the controller on the mb or is it something in the hard drive itself.

i did try fdisk and it keeps retrying to verify drive and repeats at 12 to 15 % goes back to 0% and starts again.

Thanks in advance for any help
 

A:s.m.a.r.t. error on startup

Read other 6 answers
RELEVANCY SCORE 32

Whenever I start up my computer, a .dll error comes up saying something along the lines "Unable to locate ihorauhn.dll"
It's been happening for a while, but I haven;t noticed any changes in my computer's performance...
I tried searching for 'ihorauhn.dll' on the internet, and found nothing about it.
So, I have no idea what it was for, why it is missing, and what it does.
I was just wondering what the .dll was for and what I should do to fix it?
Thanks
 

A:DLL error on startup

Read other 8 answers
RELEVANCY SCORE 32

hi
I AM POSTING THIS THREAD AGAIN....
PLEASE REPLY
i am using a win vista operating system in my laptop
i dont know how i get RunDLL errors....
these are the errors with subject of "specific module could not found"
c:\users\.......\temp\rqRKCrOi.dll

and

c:\users\.......\temp\ssqRKbYp.dll

please help me to remove this erros

and i want to remove expired norton antivirus from my system, so how can i remove it?????

wait for reply!!!!
p
 

A:startup dll error ............

Go to control panel then click on add remove programs and uninstall norton.
 

Read other 1 answers
RELEVANCY SCORE 32

Recently, I got a wireless adapter card for my Compaq Presario (2005-6) desktop PC. Unfortunately, wireless cards have been known to freeze that model of computer if they use usb port 2.0. My comp started freezing after an hour and eventually much faster, leading to my having to shut it down by holding the power button repeatedly. Eventually it started running very poorly, so I did a destructive system restore and wiped the entire computer. I had to do this twice, because it started freezing again - the third time, it stopped freezing because I switched which port the wireless card was in, but the damage was already done.
Now windows will not start normally at all. It has no restore save points and will not allow me to try to restore either via safe mode or through hitting f10 at start up. If I try to use 'start windows normally/last good configuration', the PC simply freezes on a black screen. I have tried deleting programs in safe mode, defragging, disk cleanup, and chkdsk, none of which worked. I can't burn windows XP or boot.ini because the only other computer we have is incapable of burning CDs, and compaq did not send any system restore discs with the computer - nor did they send the XP set up cds. Is there any way for me to somehow repair XP without the discs? It seems like a huge waste of a computer to try and buy a new one when everyone else I've consulted said it sounds like a windows problem rather than an XP one.

Thanks for any advice.

A:XP Error At Startup

Do any of your friends have an XP CD that you can borrow? You could do a repair install with it then, which would most likely solve your issue.

Read other 1 answers
RELEVANCY SCORE 32

Since no-one has responded to my first post, I'll ask the qu. again...since yesterday, I've received a message upon arriving at Windows saying NDS Load String ()is Error. (Not found INI File :[C:\DRIVERS\CONFIG FREE\NDSFiles\NDSNL.ini] Microsoft are unable to help me as my Windows was pre-installed on my laptop, the Toshiba Canada website is down so there is no-one to help at all. I would really appreciate some help as to what this file is, what does ot do, how necessary is it etc. I cannot restore it with Norton System works as it seems to have disappeared! Any advice would be appreciated. Thanx

A:error msg on startup

As far as I know, NDS is Novell Directory Services. Is your laptop used on a Novell network?

Read other 3 answers
RELEVANCY SCORE 32

hi
i am using a win vista operating system in my laptop
i dont know how i get RunDLL errors....
these are the errors with subject of "specific module could not found"
c:\users\.......\temp\rqRKCrOi.dll

and

c:\users\.......\temp\ssqRKbYp.dll

please help me to remove this erros

and i want to remove expired norton antivirus from my system, so how can i remove it?????

wait for reply!!!!
p
 

Read other answers
RELEVANCY SCORE 32

Hello everyone,
 
Upon starting up my account, Windows 7, I run into an error prompt indicating "C:\User\TJ\AppData\Local\Temp\CT3306061\plugins\TBVerifier.dll the specified module could not be found." I have conducted a scan via AVG and Malwarebytes, have corrected / removed all threats, and have restarted with the error still persisting. 

A:.dll error on startup.

In my own response this topic, it has been solved for me via the following method.
 
Installed CCleaner
 
Completed scan
 
Viewed Tools - > Start-up
 
Disabled Conduit entries.
 
Restarted and error was no longer present.

Read other 2 answers
RELEVANCY SCORE 32

hi people..
i have a problem with my computer startup. Each time i boot my windows, i get a startup error saying "cannot find c:\windows\fonts\explorer.exe" due to which my computer starts slowly... So please try helping me finding a way out...

this is the log file after scanning using hijack...
Logfile of Trend Micro HijackThis v2.0.2
Scan saved at 8:20:42 PM, on 9/8/2007
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP2 (6.00.2900.2180)
Boot mode: Normal

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\Program Files\Symantec_Client_Security\Symantec AntiVirus\DefWatch.exe
C:\WINDOWS\Explorer.exe
C:\Program Files\Ahead\ODD Toolkit\DVDTray.exe
C:\Program Files\CyberLink\PowerDVD\PDVDServ.exe
C:\PROGRA~1\SYMANT~1\SYMANT~1\vptray.exe
C:\WINDOWS\system32\hkcmd.exe
C:\WINDOWS\system32\igfxpers.exe
C:\WINDOWS\SOUNDMAN.EXE
C:\Program Files\Java\jre1.6.0\bin\jusched.exe
C:\Program Files\QuickTime\qttask.exe
C:\Program Files\Messenger\msmsgs.exe
C:\Program Files\Symantec_Client_Security\Symantec AntiVirus\Rtvscan.exe
E:\Spyware Doctor\svcntaux.exe
C:\Program Files\WallpaperToy\Wallpapertoy.Exe
e:\hijack\hijac\HijackThis.exe

R1 - HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings,ProxyServer = 192.168.0.1:6588
F2 - REG:system.ini: Shell=Expl... Read more

A:startup error

Duplicate thread. Other one here: http://forums.techguy.org/windows-nt-2000-xp/621173-startup-error.html
 

Read other 2 answers
RELEVANCY SCORE 32

Hi all,

My XP machine is now taking about 5 mins to load. Once the desktop appears, I'm greeted with the rather ambiguous error "Setup Error - failed to load resources from resource file...please check your setup". I've read some posts about being a corruption in the .NET framework, but don't really know how to proceed in fixing it, or indeed if the posts I've read are related to my problem. Does anyone have any more info on what this error is, and how to go about fixing it?

Incidentally, my PC seems to run fine once it's booted.

Thanks to all who can help!
 

A:Error on startup

it maybe a lot of startup programs loading
have you looked at the startup tab on msconfig
for 98, ME, XP
start>
run>
msconfig>
startup tab
have a look at the programs listed - details available from here

http://www.pacs-portal.co.uk/startup_content.php
http://www.windowsstartup.com/wso/browse.php?l=1
http://www.3feetunder.com/krick/startup/
http://www.sysinfo.org/startuplist.php?filter=realsched

work out what you need

or you can post them here
run msinfo32
software environment
startup programs
highlight them all
control C [this will copy to clipboard]
then you can control V [this will paste from clipboard] into this post
 

Read other 1 answers