Over 1 million tech questions and answers.

280 G2 Microtower Netlogon Event ID 5719 When Using SSD

Q: 280 G2 Microtower Netlogon Event ID 5719 When Using SSD

Hello, I am currently testing the 280 G2 desktop for a desktop refresh, but I have come across a problem. The 280 G2 has an OEM SANDISK 256GB Z400 SSD. I'm using MDT to deploy Win7 x64 to the device which all works correctly. After each reboot, I see the Netlogon 5719 (no logon servers available) Event. This causes no problems during the build. However, when the computer is booted and I immediately logon on receiving the CTRL+ALT+DEL prompt, I get the cached copy of the user profile and the Intranet web page (configured in startup) fails to load. The 5719 event and the above problem are caused by the NIC not being initialised yet. I've tested this with a HDD (normal spinning disk drive) and do not get this error. So I have concluded that the faster speed of the SSD is causing some kind of race condition which loads the OS, but then has to wait for the physical NIC (integrated Realtek GBE 8111G) to be made ready. I have got around this by configuring GPO to wait for the network on logon and loading the users profile - it works but its not a great solution IMHO. Has anyone had the same problem?, is there anything that can be done to make the NIC respond faster? Thanks and regards,YYo

Read other answers
RELEVANCY SCORE 200
Preferred Solution: 280 G2 Microtower Netlogon Event ID 5719 When Using SSD

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

RELEVANCY SCORE 87.2

Good afternoon,
I've bumped into this issue, and have yet to find a good solution.

The environment
Catalyst 3560G running 15.0(1)SE with following port config

switchport access vlan <some number>
switchport mode access
spanning-tree portfast
spanning-tree bpduguard enable
Catalyst 6509 w/ VS-SUP2T-10G running 15.1(2)SY with WS-X6148E-GE-45AT blades and the following port config

switchport
switchport access vlan <some number>
switchport mode access
logging event link-status
spanning-tree portfast edge
spanning-tree bpduguard enable
The vlan interface on the 6509 is configured as...
ip address 10.xx.xx.252 255.255.255.0
ip broadcast-address 10.xx.xx.255
ip helper-address <ip of DHCP server>
ip helper-address <ip of SCCM server>
no ip redirects
ip directed-broadcast
ip pim sparse-dense-mode

We are using ip helper on the switches. There is no 802.1x configuration that might be fiddling with port settings.

I've been testing with this problem against both switches to rule out network differences.
Monitor ports have been configured on the switches so we can watch the traffic to/from the workstations that are experiencing the DHCP timeouts.

The endpoints are workstations running Windows 7 with SP1.
The problem
We're seeing lots of NETLOGON 5719 errors on boot up. This is breaking group policy processing and a few other boot time processes. The root cause appears to be DHCP requests timing out, whic... Read more

Read other answers
RELEVANCY SCORE 81.2

Hi all,
I'm about at my wits end trying to fix this issue, and require your assistance please.
On multiple Windows 7 PC's in our environment, we are getting these types of errors:
Log Name:      System
Source:        NETLOGON
Date:          12/11/2019 3:05:06 PM
Event ID:      5719
Task Category: None
Level:         Error
Keywords:      Classic
User:          N/A
Computer:      P37905.domain.local
Description:
This computer was not able to set up a secure session with a domain controller in domain DOMAIN.LOCAL due to the following: 
There are currently no logon servers available to service the logon request. 
This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator.  

ADDITIONAL INFO 
If this computer is a domain controller for the specified domain, it sets up the secure session to the primary domain controller emulator in the specified domain. Otherwise, this computer sets up the secure session to any domain controller in the specified
domain.
-----------------------------------
Log Name:      System
Source:        Microsoft-Windows-GroupPolicy
Date:          12/11/2019 3:05:06 PM
Event ID:    &nb... Read more

Read other answers
RELEVANCY SCORE 74

We have about 100 Windows 7 machines composed of 3 different models of computer.
The newest two models are logging NETLOGON Event ID 5719 at startup.  This has the knock on effect of causing group policy processing to fail at startup which in turn stops all group policy deployed MSIs being installed.
If we assign a static IP to the machine the error goes away.  On some machines if we disable the firewall and set the network connection to 1Gbps rather than auto the error goes away.  Obviously these aren't very useful solutions.
The oldest of the computers don't seem to have this problem as they take longer to boot up, which seems to allow the network connection time to become fully operational before netlogon starts.
I've tried a number of 'fixes' that don't work:


setting NETLOGON ExpectedDialupDelay to 200 via both group policy and the registry
setting the NETLOGON service to be dependant on various other services including DNS, DHCP client, TermService, Firewall..
set Kerberos to use TCP using the MaxPacketSize registry value

The computers are plugged into a mix of 100Mbps and 1Gbps managed switches.  Spanning tree is not enabled.
Our 600 or so Windows XP clients are unaffected.
 
Any help would be greatly appreciated.
 
netlogon.log

05/07 16:21:09 [INIT] Command line parsed successfully ...
05/07 16:21:09 [INIT] Netlogon.dll has been unloaded (recover from it).
05/07 16:21:09 [PERF] NlInit: New NlPcG... Read more

A:Event id 5719 stopping us deploying software

Thanks Dale.
 
It turned out the solution was to set "Startup policy processing wait time" in group policy.  It's located under Computer Configuration | Policies | Admin Templates | System | Group Policy.
 
Although it states the default is 30 seconds for Vista it appears Windows 7 doesn't wait at all.  The computers now pause for a few seconds at "Applying computer settings" and then correctly process group policy.

Read other 10 answers
RELEVANCY SCORE 66.8

Greetings,

I am just trying to hammer out the issues I find in event viewer. Here is one of them:

Event ID: 3095
This computer is configured as a member of a workgroup, not as a member of a domain. The Netlogon service does not need to run in this configuration.

I am, indeed, a part of a workgroup and NOT a domain. What could the Netlogon service do for me as apart of a workgroup as opposed to a domain?
This took place while I was sitting in front of the computer but I have no idea what would cause this error. Any ideas?

A:Event Viewer - Netlogon service error

It may be configured to start automatically in Services, and can't start and complains. If it is not running and you have no problems, then just keep it from trying to start in the first place.

Go to Start, Run, services.msc and scroll down to the Net Logon service, right click, Properties, set Startup type to manual or disabled, OK.

Read other 1 answers
RELEVANCY SCORE 65.6

Hi there,

i am having some issues with an upgrade on Windows NT 4.0 to Windows 2003 Stamdard with Active Directory.

The environment consisted of one Windows NT 4.0 PDC and four Windows NT 4.0 BDCs. As per the Microsoft recommended method to upgrade this environment to Windows 2003 I performed the following:

1. Build a new Windows NT 4.0 server with SP6.0a as a BDC on the production network.
2. Promoted this newly built BDC to a PDC whilst on the production network.
3. Ensured that the old PDC had been demoted to a BDC and that all servers were happy replicating with the newly built PDC.
4. I then removed the newly built PDC from the network, upgraded it to Windows 2003 Standard with Active Directory, turned on the registry setting to make this Windows 2003 a NT 4.0 emulator, and connected it back to the production network.
5. I then checked server manager on the BDCs and confirmed that they could "see" their DC again, and the DC could see the PDCs.
6. I left the server to run overnight then the next day I returned to it and ran the command "Nltest.exe /bdc_query:<domain name> to show the connection and replication status of the BDCs.

This is where I ran into problems.

Two out of the five BDCs were quite happy showing a connection status of SUCCESS and were replicating happily between themselves and the DC according to the Event Viewers on both the 2003 DC and the two BDCs.

These two servers were correctly displaying the status code 0 0x0 NERR_SUCCES... Read more

Read other answers
RELEVANCY SCORE 44

hi with netlogon how do i make it open a program so when i login it automatically opens a program?
 

A:Netlogon

You don't netlogon is only a service.... It does not have this capability.

What you want to do is put the program into the startup group. It will then start on each reboot.
 

Read other 3 answers
RELEVANCY SCORE 43.6

Alright, started getting the 1001 BugCheck crash with Event 41 Kernel-Power BSOD a few times not long ago, widely spaced out incidents (it will lock up, make a very weird repetitive noise through my stereo speakers and will also get black and white bars across the screen before the blue screen turns up and asks for restart option choice). And Event 4 k57nd60a has been ongoing for as long as I can remember.

Any ideas?
Event 1001, BugCheck
The computer has rebooted from a bugcheck. The bugcheck was: 0x0000003b (0x00000000c0000005, 0xfffff8800646843a, 0xfffff880028c5a10, 0x0000000000000000). A dump was saved in: C:\Windows\MEMORY.DMP. Report Id: 041312-18205-01.

- <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
- <System>
<Provider Name="Microsoft-Windows-WER-SystemErrorReporting" Guid="{ABCE23E7-DE45-4366-8631-84FA6C525952}" EventSourceName="BugCheck" />
<EventID Qualifiers="16384">1001</EventID>
<Version>0</Version>
<Level>2</Level>
<Task>0</Task>
<Opcode>0</Opcode>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2012-04-13T14:05:58.000000000Z" />
<EventRecordID>39029</EventRecordID>
<Correlation />
<Execution ProcessID="0" ThreadID="0" />
<Channel>System</Channel>
<Computer>M... Read more

A:Event 1001 BugCheck Event 41 Kernel-Power Event 4 k57nd60a

Memory exception but we need to examine the DMP files to find out why.

We do need the DMP file as it contains the only record of the sequence of events leading up to the crash, what drivers were loaded, and what was responsible.

If you are overclocking STOP
We could also use some system information, which you can get easily by running msinfo32.
To do that go to start>run>type msinfo32>enter

When it is finished running go to file>save>name it and upload to us here.
You may be able to get the DMP files without crashing by booting into safe mode (F8) with networking.

To enable us to assist you with your computer's BSOD symptoms, upload the contents of your "\Windows\Minidump" folder.

The procedure:





Quote:
* Copy the contents of \Windows\Minidump to another (temporary) location somewhere on your machine.
* Zip up the copy.
* Attach the ZIP archive to your post using the "paperclip" (file attachments) button.
*If the files are too large please upload them to a file sharing service like "Rapidshare" and put a link to them in your reply.


To ensure minidumps are enabled:





Quote:
* Go to Start, in the Search Box type: sysdm.cpl, press Enter.
* Under the Advanced tab, click on the Startup and Recovery Settings... button.
* Ensure that Automatically restart is unchecked.
* Under the Write Debugging Information header select Small memory dump (256 kB) in the dropdown box (the 256kb ... Read more

Read other 9 answers
RELEVANCY SCORE 43.2

I have a DHCP domain and some of my PC's are unable to logon to the domain I receive netlogon service not running. I go into service and try to manually start the service and I get an error -- "the dependancy service or group failed to start."

 

A:Netlogon service

If the machines are unable to get an IP address from the DHCP server, the netlogon service will not start. Check the TCP/IP properties on the client machines and make sure they are setup for DHCP. Also, try doing ipconfig /release & renew.
 

Read other 2 answers
RELEVANCY SCORE 43.2

This is a tough one...NT 4.0 network with w9* clients. Receiving error 1015...unable to update configuration from \\server\netlogon\config.pol the registry is corrupt... OR error 1016...an I\O operation initiated by the registry failed unrecoverably.... I believe the config.pol file may be corrupt and has corrupted the registries of the clients. anyone know where to edit the registry on win9* machines? i DO NOT want to re-install windows on all the clients. any ideas at all would help, i've been trying to figure this one out for a week and it's getting worse. would overwriting the config.pol file on the NT box help? I'm pulling my hair out here.
 

A:NT netlogon errors

Darren,
Delete the config.pol from the server, create a new one if desired, Save the file as Config.pol in the Netlogon folder of either the primary domain controller or the backup domain controller. The Netlogon folder is located in the following folder:

C:\Winnt\System32\Repl\Import\Scripts

Then try to log in again in some workstations and let's see if this will fix it.

I you don't want to delete, then rename it to config.old. login in one workstation and see what happend.

Good luck

T
 

Read other 2 answers
RELEVANCY SCORE 43.2

Hi Guys,

I'm running an NT 4.0 network. I have a problem with my netlogon folder. The users on my network can navigate to this and have access to it. Is there any way of changing the permissions so that it will still work ok but they can't do anything to it. Just out of interest what should the netlogon folder permissions be anyway incase i've just set it up wrongly.

Any help will be gratefully received,
Cheers
Speckee
 

Read other answers
RELEVANCY SCORE 43.2

I got this dell laptop running xp pro and when I try to log on I get.

Unable to log you on because the netlogon service is not running on this machine.

This was in safe mode.....so am I SOL? What I do? I think I may have deleted something out of the registry....I did back it up first and I was going to restore it.....but I can't log on.
 

A:Solved: netlogon

Read other 10 answers
RELEVANCY SCORE 43.2

Hello.
My Netlogon Service stopped and when I want to start it show me an error about dependencies. Workstation Service is set on "Local System account" but how about Netlogon service? Should it on "Local System account" too?
Thank you.

Read other answers
RELEVANCY SCORE 42.8

Hi there,

Heres my problem:

I have an Microsoft NT Back Office 4.5 that belongs to a client of mine. I got a phone call that that users are unable to connect to the server.

I arrive at the scene, and try log into the server localy with the Administrator username and password. It tries to authenticate, but then I get the error message that NETLOGON services are not running on this machine. So therefore there is no way for me to logon to the machine.

I bounce (reboot) the machine, still no joy.

What do I do now? I cant logon to the machine to do anything... so I really dont know what to do. There seems to be no other way into the machine. Could I possibly take the hard drive out the box, slave it in another machine and try edit the registory that way? Is that possible? If so, where/how would I do this?

Any other ideas?

Your help on this would be greatly appretiated.

Pathios
 

A:Windows NT NETLOGON Problem. HELP!!!

http://www.petri.co.il/forgot_administrator_password.htm
http://www.windowsnetworking.com/kb...ecoverLostWindowsNTAdministratorPassword.html
http://techrepublic.com.com/5100-22_11-5455038.html
http://www.petri.co.il/forgot_administrator_password.htm#2

Check these out...doc
 

Read other 2 answers
RELEVANCY SCORE 42.8

I have a Windows XP SP3 (current patching and trend micro current and scans clean) user who keeps losing his connection to the file server, but he does not loose connection to the internet. This happens at random times but mostly during the night while the pc is on but logged off. All the hardware has been switched (Network card, patch cable, wall outlet and switch. I have reinstalled Trend Micro.
He gets several errors:
Event Type: Error
Event Source: AutoEnrollment
Event Category: None
Event ID: 15
Date: 8/8/2010
Time: 9:17:24 PM
User: N/A
Computer: 200-CEO
Description:
Automatic certificate enrollment for local system failed to contact the active directory (0x8007054b). The specified domain either does not exist or could not be contacted.
Enrollment will not be performed.

Event Type: Error
Event Source: NETLOGON
Event Category: None
Event ID: 5719
Date: 8/6/2010
Time: 1:17:17 PM
User: N/A
Computer: 200-CEO
Description:
No Domain Controller is available for domain IRONCOUNTY due to the following:
There are currently no logon servers available to service the logon request. .
Make sure that the computer is connected to the network and try again. If the problem persists, please contact your domain administrator.
vent Type: Warning
Event Source: LSASRV
Event Category: SPNEGO (Negotiator)
Event ID: 40961
Date: 8/5/2010
Time: 1:52:02 PM
User: N/A
Computer: 200-CEO
Description:
The Security System could not establish a secured connection with the server ldap/IRO... Read more

A:XP with netlogon and autoenrollment errors

Mod bump as it sat a few dats in wrong forum.

Read other 2 answers
RELEVANCY SCORE 42.8

Hi,

I am not able to connect into the domain. I get an error that the Windows netlogon service is not started. But when I go into services, I can not even see the netlogon service. I also can't see the workstation service.

Its a windows xp with the latest patches etc.

When I try to disjoin the computer from the, I get the following error:

"he identification of the computer cannot be changed because networking is not installed or is not properly configured"

Please help.

Thanks
 

A:Missing Netlogon Service

Looks like the registry entries got deleted:
KEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Netlogon
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\lanmanworkstation

You could do a system restore, or if you are comfortable editing the registry import them from the registry of another PC running XP and restart windows (probably easier).
 

Read other 2 answers
RELEVANCY SCORE 42.8

Hi,

It happens in Windows 7 and Windows 10 workstations.

Issue : Domain Admin is suddenly missing from the Administrator group for the workstions. 
Reason : Netlogon service is showing like below



System event log shows as below










"LanmanWorkstation" is exists in the "DependOnService" value under HKEY_LOCAL_MACHINE/System/CurrentControlSet/Services/Netlogon/
Local Administrator account is disabled as per organization policy. so workstation is not having any administrator account to start the netlogon service

Please help

Regards, Boopathi

Read other answers
RELEVANCY SCORE 42.8

I recently encountered a problem on the networking of Win 7 professional. My laptop is installed with Windows 7, 64bit, with Service Pack 1.

I have shared some local folders via my home WLAN so I can access the files while using my other devices in living room, bedroom, and etc. It's been going quite well, until one night last week. I couldn't access my local files thru WLAN. It kept saying that
User login information is not correct but I've double checked that user name and password are both correct. Besides, the sharing settings of my local folders are all the sam as they were.

Based on my poor IT knowledge, I checked services running on my laptop and found Netlogon service shows "Manual" and stopped. I tried to change it back to "Automatic" and then started it. Then a dialogue box poped up saying: "The
netlogon service on local computer started and then stopped. Some services stop automatically if they have no work to do". And the service stopped.

And after I restarted my laptop, I found the Netlogon service was again switched back to "Manual". And I repeated the previous steps but it kept showing that message. I restarted the computer several times and it's still the same.
I didn't install any softwares last week before the problem occurred, except the Windows update KB4480907 and KB2808679. And the laptop have been running very normally since last December, with no blue screen or forced shut-down.

Another strange t... Read more

Read other answers
RELEVANCY SCORE 42.8

I recently encountered a problem on the networking of Win 7 professional. My laptop is installed with Windows 7, 64bit, with Service Pack 1.

I have shared some local folders via my home WLAN so I can access the files while using my other devices in living room, bedroom, and etc. It's been going quite well, until one night last week. I couldn't access my local files thru WLAN. It kept saying that
User login information is not correct but I've double checked that user name and password are both correct. Besides, the sharing settings of my local folders are all the sam as they were.

Based on my poor IT knowledge, I checked services running on my laptop and found Netlogon service shows "Manual" and stopped. I tried to change it back to "Automatic" and then started it. Then a dialogue box poped up saying: "The
netlogon service on local computer started and then stopped. Some services stop automatically if they have no work to do". And the service stopped.

And after I restarted my laptop, I found the Netlogon service was again switched back to "Manual". And I repeated the previous steps but it kept showing that message. I restarted the computer several times and it's still the same.
I didn't install any softwares last week before the problem occurred, except the Windows update KB4480907 and KB2808679. And the laptop have been running very normally since last December, with no blue screen or forced shut-down.

Another strange t... Read more

Read other answers
RELEVANCY SCORE 42.8

Hi, 
We have Windows 7 client machines which are joined to domain.
But we are unable to dis join from domain and getting below error.

We have check and found Netlogon service is missing in services.msc console.
We also verified registry setting of netlogon, Lanmanworkstation and lanmanserver setting are compared with working machine and found all are same.
Please let me know to recover or reinstall the Netlogon service on problematic client machines... 

Read other answers
RELEVANCY SCORE 42.8

I have an NT 4.0 server that will not allow ANYONE to log in. All get a message saying the netlogon service is not running so the system cannot log them in. This is a somewhat critical machine and I would like to know if there is a way to either log in and start the service again or start it some other way. Thanks for any help...

Pat Russell
 

A:Netlogon service not running

I had exactly the same problem with a Windows NT 4.0 workstation. The solution that Microsoft gives is to install Service Pack 6 but you can't do that if you can't log in, can you?
What I had to resort to doing is reinstalling Windows NT 4.0 Workstation, leaving the data intact but that can cause more problems then it is worth as programs lose registry keys and may stop working.
If you have a backup of your data on the Server, the best is to reinstall Windows NT Server and wipe all data while reinstalling.
The Netlogon service will work once reinstalled.
Unfortunately, I found no way to bypass the logon.
If you find out another solution, I would love to know.
 

Read other 1 answers
RELEVANCY SCORE 42.8

i can no longer log on to my company's domain with a host system. it gives me the following error: "Unable to log you on because netlogon service is not running on this machine"
can anyone please help me out? Thanks. Tots.
 

Read other answers
RELEVANCY SCORE 42.8

A thread from last year (5/2001) that the best fix is to reinstall the OS and install SP6. My problem is that SP6 is already installed on the server. I am concerned that the reinstall/fix will delete software (obviously a great concern) and it is specialized surveillance software that I am unfamiliar with. The server doesn't act as a file server but rather as the security utility operator.

Please help.

Thank you.
AMRS
 

A:Netlogon Service NOT running BUT has SP6

Reinstalling the Service Pack will not damage any files, just replace any damaged ones that the service pack has.

Reinstalling the OS will kill all your settings and reset the registry, so you would have to reinstall all the programs again.
Can you start it manually?

Is there an event in the event viewer that might give you a little more to go on?
 

Read other 3 answers
RELEVANCY SCORE 42.8

Every time I start up my Windows XP computer, an error message appears in the event viewer
 
 
 
This computer is configured as a member of a workgroup, not as a member of a domain. The Netlogon service does not need to run in this configuration.
 
but the problem is, this computer is not a member of a domain or a workgroup. it is just a computer hooked up to my high-speed internet. Google only showed results for people trying to set up a domain and one result from someone with a workgroup, and that guy had no replies, but there was nothing regarding the error message for computers with neither of those, nothing for home computers hooked up to the internet.
 
I was wondering if you can help me find the cause and help me fix it

A:"netlogon" error every startup

http://answers.microsoft.com/en-us/windows/forum/windows_vista-security/event-id-3095/d6e41ae9-1e51-461b-9f41-34af8821da36?db=5&auth=1
 
Louis

Read other 1 answers
RELEVANCY SCORE 42.8

I am running a Windows XP machine in a Windows 2000 network. Everytime the Windows XP machine reboots it gets these errors:

Netlogon 5719 & w32time 14

I have been researching these errors for a while and I am lost. The computer has full functionality, except when logged onto the database on a remote computer for long periods of time, and does not give errors when logging on.

However if you go into the event viewer after booting up there is 1 Netlogon event and 3 w32time events.

I have tried updating the NIC driver, replacing the NIC, switching ports on the switch, extending the netlogon timeout time, and disabling the spanning tree algorithm on the port.

I need to fix this issue before we have a bigger issue. If anyone has any suggestions please tell me.

Thank you.

A:Netlogon & W32time errors

is there a description that goes with each error?

It may be that there is no domain controller for the domain...
see here..MS technet article

and here...MS Knowledgebase article

Read other 2 answers
RELEVANCY SCORE 42.8

Hello to all of you.

I wish to know the importance of the following windows system files.

1. secli.dll
2. netlogn.dll
3. eventlog.dll

I have seen many a times while the forum guys are helping people in removing the virus/malware etc they are interested in the location of above files. Are they very crucial to the system?

For providing the above information, I am thankful to all of you.

With kind regards.
Manoj

A:secli.dll netlogon.dll eventlog.dll

Presumably you meant: SCECLI.dll, not secli.dll.

Googling all three files, seems to indicate that they are all legitimate Windows files.

Check the properties of each file in Windows\System32 for confirmation.

I don't generally delete files which have presumably been installed by the OS.

This is what appears in my Windows\System32:

All 3 files dated 14.4.2008

(modified the 29.8.2002 files, on installation of SP3)

1. scecli.dll

Windows Security Configuration Editor Client Engine

5.1.2600.5512
(xpsp.080413-2113)

2. netlogn.dll

Net Logon Services DLL

5.1.2600.5512
(xpsp.080413-2113)

3. eventlog.dll

Event logging service

5.1.2600.5512
(xpsp.080413-2111)

Read other 2 answers
RELEVANCY SCORE 42.8

Hi Sir Paul i need your help again. I have here HP 280 G1 Microtower PC dome driver is missing please help me on this. Thank you very much in advance.    













Solved!

View Solution.

A:HP 280 G1 Microtower PC Driver Problem

Hi, Please try Intel Chipset Driver (International)Intel Management Engine Interface Driver (Eastern European, International) from the following link:    http://h20564.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=7357749&swLangOid=8&swEnvOid=4158 Regards,

Read other 5 answers
RELEVANCY SCORE 42.8

Hello Everybody, Is it possible to get Windows 10 installed on HP DX 6120 MT. If so, will any hardware changes be needed? Thanks in advance.

Read other answers
RELEVANCY SCORE 42.8

Hello Everybody, Is it possible to get Windows 10 installed on HP DX 6100. If so, will any hardware changes be needed? Thanks in advance.

A:Windows 10 on HP DX6100 Microtower

BikashN Sorry, but the realistic answer is NO! The latest HP drivers for your PC are for Vista, and without HP drivers, even if you can force an installation, you will be then stuck using the generic MS drivers, and those provide only the most basic functions. Stuff that is likely NOT to work include the display, audio, and networking. Also, there is no Upgrade Path from anything prior to Win7 for Win10; meaning, that you would have to do a clean-install which would remove everything you currently have. ========================================================================I am a volunteer and I do not work for, nor do I represent, HP.---------------------------------------------------------------If my posts helped you, please click the Thumbs-Up symbol on my post to say thanks.If my posts solved your problem please click "Accept As Solution".========================================================================

Read other 1 answers
RELEVANCY SCORE 42.8

I have one of these units and am trying to install windows 98 on it. I deleted the previous partition and formated the drive and installed windows 98. Before i installed windows 98 i went into BIOS and disabled the on-board audio, lan and usb. I finished the install of windows 98 and it goes to the windows 98 booting screen and it just keeps loading for ever. I restart and was able to go into safe mode but can not go into normal mode. Is there a reason why not? Anyone know? I am using the on-board video card. Would this be the reason why? The computer should be able to run windows 98 especially since i will not be using all of the accesories like usb, audio, lan, etc. What you guys think? The hardware is the lastest from HP like serial harddrive and etc. but i do not see a reason why it should not run windows 98.
 

A:HP Compaq DX2200 Microtower

i am still having no success. i disabled basically everything even the serial ports and it still does not want to load windows 98 in normal mode?

anyone have any ideas why?
 

Read other 2 answers
RELEVANCY SCORE 42.8

i want to buy gtx 960 and i want to ask if it will run on my pc i have already psu 500w so just asking if i will run my gtx 960 without problem ??  http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c02779504 this is my pc specs

Read other answers
RELEVANCY SCORE 42.4

when i try to add my system in domain it cannot..when i check the netlogon service it is not activated
how i can activate the netlogon

Read other answers
RELEVANCY SCORE 42.4

I found this in the inbound rules in the Windows 8 firewall, its a fairly fresh install (12 hours) and the "Authz" looks like some kind of "1337speak".

As I am typing this Microsoft Management Console popped up on top of the firewall blocking my view into the properties of this rule, and I am unable to close it.. I do remember that the process is lass or something like that though..

Any help on this would be great?

Has anyone seen this?

A:Firewall: Netlogon Service Authz (RPC)

I was able to close MMC via task manager.. the process is "%SystemRoot%\System32\lsass.exe", and the description is "Inbound rule for the NetLogon service to process remote authz requests via RPC/TCP."

Read other 1 answers
RELEVANCY SCORE 42.4

Hi. A week ago, my computer got hijacked with the about:blank. I used several spyware removers, and was able to remove and reset my IE. The problem I now face is that whenever I restart my computer, a new hardware detected "Workstation NetLogon Service", and it's wanting to install on my computer.

I have read all I can about Workstation NetLogon Service. I do not have it installed on my computer, so I can't disable or stop it under Services Management. I believe it's connected to the about:blank hijack, because before then I didn't have this hardware detection. I can't delete the hardware because it's not actually installed.. I don't know what to do.

A:About:Blank & Workstation NetLogon Service

As you have read the Net logon service "Supports pass-through authentication of account logon events for computers in a domain."
This is usually installed by default on a Windows XP computer but
is set to manual start. If it were installed you could go to Start, Run, type
cmd and then type net stop netlogon and it would stop the service.

It maybe this virus and may have added the entry in the Registry.
http://securityresponse.symantec.com...rmageddon.html

I would recommend making sure that Windows is up to date and running
the Trend Micro online virus scan if you have broadband.
http://housecall.trendmicro.com/

Read other 2 answers
RELEVANCY SCORE 42.4

What is maximum supported RAM size for motherboard Hewlett-Packard 18EB. 18EB (0x000000F0 - 0x000024F0) Windows 10 x64, Intel(R) Core(TM) i7-4770 CPU @ 3.40GHz , Socket 1150 LGA (0x1), Haswell  

A:Supported RAM size on HP ProDesk 490 G1 Microtower PC for Wi...

HERE IS THE MANUAL for that model line.  The support documents indicate:Up to 32 GB DDR3 Synchronous Dynamic Random Access Memory (SDRAM

Read other 1 answers
RELEVANCY SCORE 42.4

my hp compaq dx2400 microtower shut down and it stopped working .jst light the green len in powersystem and when i switch it on the fans wants to run bt they stops" please assist me to get it working

Read other answers
RELEVANCY SCORE 42.4

It seems that the DC5800 is using the Analog Devices - AD1884JCPZ intrgrated circut.  My research indicated that the chip puts out S/PDIF.  I do not see any option with my current audio driver to use S/PDIF in the sound output dialogue.  Is there a way to use S/PDIF on this machine?  I have a nice DAC I would love to use.

Read other answers
RELEVANCY SCORE 42.4

Hi all, We try to install HP Ethernet 1Gb 2-port 332T adapter to HP ProDesk 400 G2 Microtower PC, but after power-up - speeker beep five times. Same situation on HP 280 G1 Microtower PC. We test this adapter on HP ML10 v2 server - system starting up without any problems. I know, this adapter is designed for servers, but why PCIe device does not run on the PC? Other server network adapters, such as Intel i350 work without problems. Thanks for the help.

Read other answers
RELEVANCY SCORE 42.4

Hello,

You may get information about my Desktop on my specs. I have precisely an HP Compaq DX2300 Microtower and I recently get a 1GB RAM stick with a friend as he change everything on his PC. The RAM that I use is DDR2 667 Mhz but the one I got with my friend I do not know what it is exactly. I can see that there is 1GB DDR2-533 but I do not know what it is.

I would like to know if someone could tell me what number of Mhz it is? And also if this will work on my PC.

Thanks in advance for any help
Ultiweap
 

A:RAM compatibility HP Compaq DX2300 microtower

Well your specs say you have DDR2-800 Mhz RAM module, whereas the one you've got from your friend is 533 Mhz stick, and 1) they won't work together 2) you wouldn't want to use a slower module than the one you already got, which is faster off-course. Hope that answers your question.

Now, getting another 1GB would improve your system's performance, perhaps you can trade this 533 Mhz stick with some IT parts shop over there, and get another 800 Mhz stick. Regards.
 

Read other 9 answers
RELEVANCY SCORE 42.4

Hi all,Problem stands as:Computer after startup screen show " no option to boot to" message in black background.If conected to network trying to PXE boot over IP6In BIOS setup>Device Config - HDD and DVD listed, also show any USB device if pluged in. BIOS not allow to save any changes in settings(no errors, no messages, but revert to previous state)Error message if try to reset to factory defaults or save settings as default.F9 Boot meniu list only IP6 and IP4 UEFI boot devices(endles list ~100 entries or so)If try to enter BOOT ORDER in BIOS  - PC seizes up, have to powercycle.CMOS reset ( even batery removal for 1 min ) doesn't make change.BIOS v 02.18 ( 05.09.2014 )Win10 x64(unaccesible anymore) Any advice appreciatedThank you

Read other answers
RELEVANCY SCORE 42.4

I just bought a HP 280 G2 Microtower Business PC (Video card Intel HD 530) and Dell U2711 (Support 2560x1600):After updated driver the Graphic control panel still only let me choose to maximum 1650x1050 (60p Hz).How can I increase my screen resolution to 2560. I had read on the Quic specs of HP 280 G2 MT that this resolution "Only supported on displays connected to the external DisplayPort connector" but it does not have a Displayport. What can I do?

Read other answers
RELEVANCY SCORE 42.4

Hi, I already have the Dell Ultrasharp U2713HM monitor which can display 2560x 1440 (60hz) via DVI-D and mini-display port (but not HDMI as the people at Dell decided to put on a HDMI port which could only display 1920x1080). Just wanted to get some advice as to if this desktop (which has a DVI-D port) will be able to run my monitor at max resolution and 60 hz.  Thanks in advance (sorry if this is obvious!/In the wrong subforum) Jack

Read other answers
RELEVANCY SCORE 42.4

I have five microtower 3400 desktops. do they support uefi ?

Read other answers
RELEVANCY SCORE 42.4

Hallo! Today got from a good old friend a pc so i can start to game abit i heave upgrade the ram to 8GB DDR2 from Elixir and 2 HDD from WD 250GB windows 7 ulti x64 install no problem at windows update all ok as soon as i want to reboot after bios pos nothing... windows wont start enymore if i stop the pc from the power button and then start normally its all ok i did try to enable or disable some options nothing CLEAR CMOS still the same....so if anybody can help me with some suggestion i w8 appreciate it!! HP s/n:  CZC92228TS and p/n:  AJ408AV EDIT! CPU intel 775 core 2 quad q6600GPU GT 210 1 GB

Read other answers
RELEVANCY SCORE 42.4

Hi, I want to add SSD as a primary drive (OS and programs) to my HP Compaq 6200 Pro Microtower (and keep my HDD as secondary - for data storage). The specifics of my configuration are: i5-2400 processor, 16GB RAM, 500GB HDD, Win 10 OS (64-bit).Can someone, please, help me with the most suitable SSD?Product specifications state 80GB to 160GB SSD support - I want to add 120GB or 128GB SSD - are there any specifics I have look up for?Any information will be helpful. 

Read other answers
RELEVANCY SCORE 42.4

I own a Microtower dc5800, running now Windows 10 Pro 64bit with no problems! Installed sare 3 HDD's, and I would like to be able to install at least 2 different OS'es, the already running Windows 1o Pro and on a second HDD a Linux Debian 8 Server. The BIOS is updated to the latest version 1.60.While booting the computer, use F9 for the Boot Menue and choose HDD, the computer boots directly into SATA01 with Windows 10 and I didn't have any choice for to choose any other HDD! How do I could choose a different HDD for to boot from?  I checked all over in the Bios and didn't found any solution. Could someone please explain in details the How To........? Thanks a lot for any information and help! Regards

Read other answers