Over 1 million tech questions and answers.

Hard drive then maybe motherboard?

Q: Hard drive then maybe motherboard?

this all started last saturday. I woke up and i was hearing clicking coming from my computer. I moved the mouse to get out of the screen saver and it froze up... I restarted and windows xp pro wouldn't boot up, it would just sit at the loading screen and i would watch the little blue thing go from right to left o.o after that i restarted and got into safe mode to try and run chkdsk. it stoped at 22% and the system started to freeze up, but i would move my mouse and move widows around... but thats about it. from there i rstarted again. the drive no longer shows up on the ata133 onboard controller.

I took the drive to a shop and they ghosted the drive to a new one. the guy mentioned that the drive was giving him some trouble and that it was definatly bad. Anyway, i got the new drive yesterday. I plugged it into the same spot and all worked well... until i was watching TV on the TV tuner card it started to freeze up again. the tv was still playing but i couldn't do anything, so i restarted and then couldn't get into windows... then the drive didn't show up. SO! i moved the drive over to the primary IDE controller where i am now, in safe mode cause windows xp still wont load (this time is seems to hang after i log in and durring "loading personal settings"). System specs:

Gigabyte 8PE667 Ultra (onboard promise ata133/raid)
p4 2.8ghz
1gb ddr pc2700
radeon 9700 pro
120gb Western Digital hd (system drive that originaly screwed up)
120gb Western Digital hd (another hard drive, for storage)
200gb Maxtor hd (more storage)
16x DVD-rom
Pioneer DVD-rw

all the harddrives are located on the ata133 onboard controller (not using the RAID function). the dvd-rom and dvd-rw are on the normal IDE controller. Right now i have the two other drives diconected from the ata133 and also disabled it and have the system disk on the normal ide controller which seems to be working fine, except getting into windows. the system drive was on it's own cable, while the other two shared one. Also when the system drive wouldn't show up, the other two did. those other two drives don't seem to be harmed though.

My thoughts are, part of the ata controller failed while i was sleeping and caused the original 120gb system drive to fail also. Then with this new drive, i caught it sooner. My concern is that the rest of the motherboard will fail also, and i will lose more then just another harddrive, if it is the motherboard.

So, here i am to see what you guys think and how i should go about fixing it. i think i gave all the info, but in this state of tiredness, i dunno. if you need more details, then say so. did i mention already that there were no error messages? any, yea... no errors. just that the system hung, kinda... and the drive didn't show up.
Pwolf

RELEVANCY SCORE 200
Preferred Solution: Hard drive then maybe motherboard?

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: Hard drive then maybe motherboard?

You could have some kind of virus that destroys your hard drives.

Read other 1 answers
RELEVANCY SCORE 52

My one-year-old out-of-warranty HP Pavillion dv1000 laptop (Windows XP Home) has been slow or unable to reboot, so I'm trying to diagnose it and figure out if I just need a new hard drive (where can I find instructions on upgrading a hard drive on this laptop?) or have to replace the whole laptop with a new one.

One of the problems found was the hard drive was in PIO mode, so I had to repeatedly switch it back to DMA mode (using the DMA-to-PIO registry hack or remounting the hard drive). This occurred weekly until I ran SpinRite, then it stayed in DMA mode for a month.

What I think is relevant from my Event Viewer Log include:

atapi event 9s: The device, \Device\Ide\IdePort0, did not respond within the timeout
period.
atapi event 11s: The driver detected a controller error on \Device\Ide\IdePort0.
a single atapi event 26: The driver has detected that device \Device\Ide\IdePort0
has old or out-of-date firmware. Reduced performance may result. [I think this may
just be a generic message when it gets too many errors]
cdrom event 7: The device, \Device\CdRom0, has a bad block.
disk event 51: An error was detected on device \Device\Harddisk1\D during a paging
operation.
disk event 7: The device, \Device\Harddisk0\D, has a bad block.
ftdisk event 57: The system failed to flush data to the transaction log. Corruption
may occur.

Recently the main hard drive went to PIO (even though it crashed while trying to burn a DVD, strange huh?) was unable to reboot u... Read more

A:Hard drive vs. Motherboard

It could be a bad drive, a bad connection or a bad controller.

Ideally, you would take the drive out of your laptop and test it with the manufacturer diagnostic utility.

In reality, you could just take the drive out, clean the contacts, put it back in and do the diagnostics in this computer.
 

Read other 1 answers
RELEVANCY SCORE 52

Here, im like an amateur Technician. I know a lot of things, although there's something that really questions in my mind.

These are like the performance of my PC.

Normally, a hard drive can go like 32mb ( or more ) per second copying some files or something like that.

Installing Black Ops takes less than 4 or 10 minutes.

Loading a Counter Strike Source game takes around less than 2 minutes or something like that. ( For some reason. )
My friend's PC? its like fried.

Back then he told me that its not that slow. Of course i can see that it doesn't really seem to be so slow before.

After doing a format due to some reason that his PC became so slow, kinda realized that something weird is happening to his PC.

Loading a Counter strike game takes like 10 Minutes.

Installing Black ops took like an hour.

Loading a Modern Warfare 2 Mission takes like 5 minutes, In the middle of battle takes like 2 minutes. Frame Rate was really damn smooth, but its like when it reloads the sound file, it takes like a minute to load it.

Mid Battle of some game, shooting a shotgun one time sounded like BZZZZZZZZZZZZZZZRRRRRRRRRRZZZZZZZZZZZZZZZZZZZZZZZZZZZZT, then another shoot was normal.

We did another format, but it doesnt seem to budge.
One time his BIOS is telling him that his hard drive doesnt exist anymore in the system, so No boot. Next day, i opened it and checked the cables, and turned it on, it now tells me that it does exist.
So... Bad Hard drive? or Bad motherboard?

A:Bad Hard drive? BAD MOTHERBOARD!?

Have your friend run a diagnostic test on his drive.
It is best to use a diagnostic program from the drive's manufacturer.

However, I have found that Hitachi Drive Fitness Test works on most any hard drive.
Downloads
Use the bootable Linux CD.

If the drive comers out clean, then you can start to suspect the motherboard.

Read other 1 answers
RELEVANCY SCORE 52

Hey guys, in couple days im getting a new MB, cpu, ram and case. I was wondering, can i put my old hard drive in, than just install drivers and bios for my new MB?
 

A:Different motherboard but same hard drive possible?

Read other 16 answers
RELEVANCY SCORE 52

This is a similar situation as described in the locked post talking about doing a non clean install of windows after replacing the motherboard. The main difference is that Dell did a clean windows install on my original HHD during a warranty replacement of a faulty motherboard. Below is a post I made on another site in the hope of getting some help. Please excuse my very basic knowledge of computers when trying to answer my question.
I recently purchased a Dell Inspiron laptop as my main photo editing device. I was quickly disappointed in its performance despite being sold that this was my best option at the price point. The 8th gen intel i5, 8gb of ram and 2tb 5400rpm HDD was not up to the task of quickly processing large photo files. I replaced the standard hd with a 2tb SSD and was finally happy with the performance of my lap top.

A few weeks ago my computer shut down to an immediate black screen and would not start up again. I sent it back to Dell for warranty but decided it was best to return it with the original HDD. It was found to have a faulty motherboard and in/out board. Both were replaced and the original hdd was wiped and returned to factory settings. Now that i have the computer back i would like to reinstall the SSD and get back to work. Unfortunately despite being told otherwise, the computer will not boot up with the ssd installed. All that happens now is it goes to a blue screen and notifies me that a problem has occured and that windows needs to restart. ... Read more

Read other answers
RELEVANCY SCORE 52

The other day we had a storm, the power went out for a few minutes. When I restarted the computer, my hard drive was bare, it wasn't even formated. This has happened when the power goes out (not all the time). What I'm trying to figure out is if it is the motherboard or the hard drive. I have a Western Digital WD1600-JB hard drive and an Abit KV8-MAX3 (VIA K8T800) motherboard.

Thanks,

Ted
 

A:Motherboard or hard drive?

Replace the hard drive... Then if the problem persists, look at replacing the power supply before going for the motherboard
 

Read other 6 answers
RELEVANCY SCORE 52

When i went to turn my comp on it wouldnt fully boot up.. all that happend was the fan was running... no beeping or anything.. so i thought it was my power supply so i put a brand new one in and went to turn on the comp and its still doing the same thing.. so now im thinking its either the mobo or hd.. i have no clue how to figure this out so if someone could help me that would be great...
 

A:Motherboard or hard drive?

I'm having the same reply as you. One thing I hope for me its the motherboard. It suck if it was the HDD. Have so much stuff on the HDD.
 

Read other 18 answers
RELEVANCY SCORE 52

I'm having trouble with my new system.

The system is as follows:

Asus P5N-D (nForce 750i)
Intel E8500 (Core 2 Duo @ 3.16 ghz, not overclocked)
4 gb of Ram (2 x 2gb)
XFX nVidia 9800 GTX+ 512mb - Latest Drivers
Samsung 500gb SATA HD
LG Optical Drive on ATAPI port
Corsair 650w PSU
External 750gb HDD on USB interface
Vista x64 SP1 w/ all Updates

I'm getting these errors in my system log (from disk or nvstor64):

The driver detected a controller error on \Device\Harddisk0\DR0.

A parity error was detected on \Device\RaidPort1.

Reset to device, \Device\RaidPort1, was issued.

I don't use a RAID - I'm running the Samsung 500gb drive that came with the system, but this sounds like either a bad motherboard or a bad hard drive. I'm not willing to go out and buy a motherboard and/or a hard drive to see if that's the problem so I'm hoping you can help. Please let me know how we can work this out, ASAP. I bought a nice, new fast gaming PC, so I'd like to actually play a few games.

I've ripped out and reinstalled the nForce drivers several times, including using DriverCleaner in Safe Mode to really get rid of them. I've installed the previous version of the nForce drivers. I've disabled command queing and write caching. I've tried another SATA port on the motherboard.

I've opened a topic on the iBuyPower forum (where I bought the system recently) in case there's more info there that might help:

http://www.i... Read more

A:Motherboard or Hard Drive?

Read other 11 answers
RELEVANCY SCORE 52

My Dell Inspirion 6000 Notebook has the dreaded Blue Screen with c000021a (Fatal System Error) and will not boot to Windows. This has happened numerous times and the problem has been resolved by reloading Windows XP and the drivers and software. The system will work temporarily, but eventually shuts down and returns to the blue screen. It seems Windows XP gets erased every time the system crashes. I'm assuming the problem is either my harddrive or the motherboard. How can I tell which one is causing the problem?
 

A:Hard Drive or Motherboard?

Read other 6 answers
RELEVANCY SCORE 52

I have a Dell XPS 4100 running Windows XP Pro with 2 hard drives 1)Western Digital(master) 2)Seagate(slave) both are 80 gig 7200 rpm. The problem I am having is this: When trying to access my Seagate drive a box popped up saying the drive needed to be formatted. It was already formatted to NTFS. When I tried to format another message said it could not be formatted. To make a long story short I somehow eventually was able to format the Seagate drive. Now when I boot up I get a message saying this drive needs to run check disk, which it does and then continues booting. I can write files to the drive but when I try to access them the PC will sometimes freeze. I purchased this drive about 6 months ago because a previous drive went bad. Can my motherboard be the cause of my drive issues? Thank you
 

A:Bad Motherboard or Hard Drive

Welcome to TechSpot

In PCs anything is possible, but I don't think the mobo causes it.
Rather, check the cables and the jumper-settings on the harddisks.
Those HDs would prefer a 80-wire flat-cable, rather than a 40-wire cable.
Check that the colourcoded connectors correspond to the instructions. Check that the red control-band is on the side of the connector where pin 1 is. Check all power-connectors.
Try another IDE-cable if you have it (or borrow one).
The first (WD) should be set to Master (or Master with Slave present), not to Cable-select. The second (Seagate) should be set to Slave, again not Cable-select.
Check in the BIOS that both HDs are recognised, write down their parameters.

In the Storage & Networking forum is a "sticky", get the HD-util for Seagate from there and run it.
 

Read other 3 answers
RELEVANCY SCORE 52

I have a Latitude 600 and when I turn it on, it may take up to 10 minutes or not at all. It will only stay on about 10 minutes or so then has a message saying preparing standby in order to eject.... The battery died just before this started happening. I have been in contact with Dell support 3 times...one said hard drive dying, another said motherboard, another said power supply...so which is it? I tried to do the test by pressing Fn and the power button but that does not work. I doubt this old thing is worth putting a new motherboard. I was also advised to never try working on a laptop myself..is it really that bad? Thanks
 

A:motherboard or hard drive?

Try replacing the power adapter first. Does the computer boot normally and are you able to access all of your files and folders. If the hard drive was failing those wouldn't be the symptoms in my opinion. Also go into the control panel and change the power settings to never hibrinate and to go into standby after say 60 minutes of inactivity and turn off hard disks after at least 60 minutes. See if those things help.
 

Read other 3 answers
RELEVANCY SCORE 52

I had all the parts for my computer selected and then I noticed that the MB and the HD might not go together. Im not goog with campat stuff at all Im thinking of building a computer. Could anyone tell me if this Hard Drive will work with this motherboard?


MSI P4N SLI-FI Socket T (LGA 775) ATX Intel Motherboard


Western Digital Raptor WD740GD 74GB 10,000 RPM 8MB Cache Serial ATA150 Hard Drive
 

A:Need help with Hard Drive to Motherboard

Yes, they should work fine. The motherboard has 4 sata ports, and that drive will take one of those ports. The motherboard also should come with the data cable, so you're covered in that area as well. The thing to consider is whether your power supply has a sata power connector, like this.

There are also molex(4pin) to sata adapters, so even if you don't have one, you can get an adapter. Sata drives can sometimes be troublesome to setup, but I doubt you'll have problems with that board, as it's newer and name brand.
Good luck on the system.
 

Read other 1 answers
RELEVANCY SCORE 52

Hey guess i'm new but we'll save that.

So my laptop (compaq presario, 1.5 years old) was running very slow and choppy i ended up defrag etc. and ended up getting the blue screens of death. It was at the point the computer would work for 5-10 mins then BSOD. SOOO I reformatted totally wiped the hard drive etc. and did a fresh install of xp home (i was running pro before). Anyway, that went fine and I thought I was in the clear. Next thing I know same thing same BSOD:

0x000000F4 (0x00000003, 0x8244CDA0, 0x8244CF14, 0x805C749A)

While this happend for awhile, i began to get upset. Now the laptop is doing the PXE-E61 check media cable blah blah....

Long story short..I took it to get serviced..they told me nothing was wrong with ram OR the hard drive (wow thanks)

Then out of spite I took it somewhere else; the guy there basically just used an HD of his and installed XP and said..well it looks like a new HD is what you need. Tried that, but when I installed it...I still couldnt' get passed the media cable errors (which he didn't even have).

Yes i've tried changing boot orders etc.

Weird thing is..sometimes it will load windows...othertimes it won't? And usually when I try to install windows it says no hard disk found blah blah F3 to exit

Furthermore, in bios 9/10 times it will say NO IDE found for the diagnostic test, and only one or two times have I been able to run the test, both times giving an error something along the lines ... Read more

A:hard drive? or motherboard?

Well, if you replaced the HD and it still doesn't work right..

It could be a bad connection. Does your laptop use some kind of a tray or an adaptor for the hard drive? It may not give good contact. Maybe get another one?

I have also seen a ThinkPad that would lose the HD if you didn't bend the corner of the laptop right. Took it to the repair shop and had them re-solder all the hard drive connectors. Fixed it.

And yes, it could be plain bad HD controller.
 

Read other 8 answers
RELEVANCY SCORE 51.6

I just installed a new hard drive on my computer, I am replacing an old 7 mb HD, with a WD 60 5400. I installed the hard drive and installed Windows XP, it was working fine, then I unplugged everything to put my computer back together and it would not read the disk. I thought maybe it was a bad disk so I hooked up my old HD and it too could not be read. Is my motherboard bad? I am using a Soyo K7VTA-PRO? Any help would be appreciated. Also, I noticed when my computer was looking for the IDE controllers, there was a line that said no 80-conductor cable, could this be the problem? I know this cable makes them run better but should it keep it from reading it?
 

A:New hard drive on Soyo Motherboard

You need to use an 80 pin IDE cable. One should have come with the new hard driver. Your old drive most likely uses a 40 pin cable.
 

Read other 11 answers
RELEVANCY SCORE 51.6

Hi. I am planning to replace my motherboard and memory on my Win 7 Home premium 64b.

I've been updating MBs for 25 years and now I am getting conflicting answers regarding booting existing hard drive on new MB. My present Win 7 installation was installed on my present MB. Before I have always been able to use an existing hard drive and OS on a new MB.

Now when I asked Gigabyte if a reinstall would be required they said no, but the registry may be full of unneeded drivers etc which would affect performance. This seems a solvable issue using registry cleaners and editors.

But I am also getting opinions that Win 7 will not boot up on a new MB and reinstall OS would be required. Considering the number of programs, some on disks others from downloads. activation keys etc, this is a major problem. Has MS gone bananas? Who would benefit with this approach?

Does anyone have a definitive answer? Thanks.

Bill

A:Existing hard drive on new motherboard.

First, Windows 7 is a lot more flexible with hardware changes, but at the very least, you should run Sysprep before moving to the new board. I would greatly recommend a clean install, especially if you plan ahead to cut down on how long that would take. However, Sysprep can remove some of the drivers to allow the system to be a little cleaner.

As for the copy of Windows 7, that all depends on your license. If you have a retail license, then you are fine. It should activate on the new system without issue, and it will be legit. If you have an OEM license, then that opens the door to a whole lot of gray areas, in terms of what is considered to be a new computer, and how legit your license will be, assuming you can activate it.

Read other 9 answers
RELEVANCY SCORE 51.6

My Dell Dimension 4100 turns on but the green light does not light up...I can hear the fans running, I can open and close the dvd and cd parts...I can plug in my mp4 players and charge it..but the monitor does not show anything but a black screen. Nothing comes up.

Is my motherboard fried or did I crash my hard drive? I dont know what to try...my sister gave me the tower from her old compaq presario s4020wm but it wont work with my dell monitor. I also tried and old mv740 compaq monitor but that didnt work either. I thought I could use the old one until i got mine fixed (or bought a new one)

if I cant get mine fixed then can someone offer some advice on how to get the monitor to work with the compaq tower?

I am on my nephew's laptop and he is staying until tomorrow so after that, i wont be back for help so if I disappear...its not because I dont care, lol!

thanks so much for any advice...
 

A:did I crash my hard drive or fry my motherboard?

Read other 10 answers
RELEVANCY SCORE 51.6

I have an intel CELERON 466MHZ CPU 256MB PC 100MHZ 166PIN SDRAM, which I bought second hand. It has always had problems with sound and video programs when opening other applications, it bogs down and freezes, has trouble reading videos from CDs and takes a long time copying etc.; the hard drive seems noisier than it should be and grinds a bit now and then. It also started having problem with freezing during the memory check when bootingI imagined that the root of the problem would be the hard drive itself, judging by the symptoms.

To check it out, I installed a different hard drive and the computer turned on but would not boot, no beeps no nothing at all and the screen remained blank or gave me the "NO SIGNAL INPUT" message. I tried removing the battery and putting it back in to clear the CMOS but this did not work. I put the original hard drive back in and took the same steps again and still nothing. I also check the screen and hard drive on another computer. They were fine.

Is it reasonable at this point to imagine the problem may be with the motherboard and not the hard drive?

thanks,
babalu
 

A:problems with hard drive or motherboard?

Read other 16 answers
RELEVANCY SCORE 51.6

My Aopen AX-33 motherboard will not detect my new Western Digital WD800JB hard drive unless it is the only hard drive in the computer. I've tried every possible ide configuration that leaves the old hard drive, that has windows on it, at primary master, and none of them work. The only way the computer will recognize the new hard drive is if the old one's removed. Help.
 

A:Motherboard not recognizing new Hard Drive

Read other 7 answers
RELEVANCY SCORE 51.6

I just bought the new motherboard with new parts but not hard disk.
I am still using the old IDE Maxtor 40GB 7200rpm hard disk.
After all the connection applied, although the pc has detected the hd, but finally failed to boot in to my windows xp.

Is IDE hard disk cannot be used in new motherboard? My motherboard is MSI-7270 K9N-U.

Thanks.
 

A:IDE Hard Drive with latest motherboard...

Howdy,

If you put a Hard drive into a new Motherboard with a Operating System on it it will not work unless the motherboard is exactly the same as the one it was formatted on.

You will have to re-install the Operating System while it is on that Motherboard for it to Recognize it.
 

Read other 1 answers
RELEVANCY SCORE 51.6

Hi guys

basically im building my own pc, like new motherboard, RAM, graphics card case the lot. but i like my 500gb IDE hard drive and the mother board is sata compatible,. i have a cable converter for this but im wondering if my windows 7 OS will just run on the new mother board or not?

Thanks :D

A:Can i just plug my old hard drive into my new motherboard using my win 7 OS?

Your old hard drive will be recognised as a hard drive, but windows 7 wont be able to use it, as the windows drivers were for your last computer, so the motherboard chipset, sound , LAN, and graphics card were all set for your last system.
If you have a spare hard drive back up all your own data first, then connect it to your computer.
It may work with a default display resolution but will then probably complain about the sound hardware, lan, chipset etc. You may be able to load these drivers from your install disks.

Read other 5 answers
RELEVANCY SCORE 51.6

I have a Motherboard that is supposed to be SATA 150 ready. However, the HD I bought is a SATA 300 one. Will the HD work?
Thanks.
 

A:Hard Drive - Motherboard Compatibility

ftgml said:


I have a Motherboard that is supposed to be SATA 150 ready. However, the HD I bought is a SATA 300 one. Will the HD work?
Thanks.Click to expand...

Will it work, most of the time yes. If the drive is not compatible at a 3Gb. transfer speed you should be able to put a jumper on the drive to limit the transfer rate to 1.5Gb. and it should work.
 

Read other 1 answers
RELEVANCY SCORE 51.6

I recently had to purchase a new system. I could not re boot my old system because it would start a reboot then go back to a message stating that the system got interupted during start up. Could not open in safe mode, system restore or open in any setting. Not sure if it was a virus, but would now like to reformat the drive to give to my father in law. Does this problem seem to be a hard drive issue or a spent motherboard issue. I just replaced the hard drive last year?
 

A:hard drive or motherboard issue

Read other 10 answers
RELEVANCY SCORE 51.6

Can't install win 7 stops at starting win insignia. Any Ideas on what the problem. And how to fix.

A:XPS 7100 new motherboard and hard drive

Are you booting to the windows 7 install disk and selecting Custom Install, Drive Options to allow windows to format the new drive? Read this for instructions--
windows.microsoft.com/.../installing-reinstalling-windows

Read other 3 answers
RELEVANCY SCORE 51.6

Hi I recently bought a motherboard memory and processor bundle.

I also bought a hard drive which has 15000 RPM. Only when I received it its not SATA or SCSI but SAS harddrive

Supplied by Misco. Manufacturer is Fugitsu but Toshiba has now taken over that part of their business.

Model MBA3300RC
Can't post a link to the hard drive but google the model and it will come up.

I have then gone to much trouble to source a cable which is a SATA to SAS.
I then connected it to the mother board but the motherboard doesn't recognise it for love or money.

I know the mother board is fine because I tested it with another hard drive.

Do regular PC motherboards capable of supporting SAS hard drives?

Its an ASROCK Motherboard Model H61M-S
 

Read other answers
RELEVANCY SCORE 51.6

Hello all,

I just got a SATA2 1TB HD but my motherboard (MSI KT3 Ultra I think) only has IDE ports. What's the cheapest solution to link the two but still utilizing SATA2? I could go USB2.0 (solution: external enclosure + USB2.0 PCI card since my MB only supports 1.1) but I would much have the faster connection of SATA2. Also, if I do have to add a SATA2 PCI expansion card, it should recognize the whole TB right? I know in some instances with older MB's, if you plug in a HD it will only register X amount of GB's. Any input is very much appreciated. Thanks!
 

A:How to add a SATA2 hard drive to IDE-only motherboard.

Buy a quality sata controller card. Yes, the card should "See" the full size of the drive as long as you read the specs on the card and it says it will recognize drives of that size.

I use and recommend either promise or highpoint controller/raid cards. There are cheaper ones however you get what you pay for.
 

Read other 3 answers
RELEVANCY SCORE 51.6

was wondering if it was at all possible to take the e-machines hard drive that has windows XP installed on it and run it on a new motherboard... and it be able to read the drives???
 

A:Hard Drive with XP to new motherboard/processor.....

you will be able to read the drives but you wont be able to run windows. You will need to reinstall windows on the hard drive after you install it in the new computer. then you will have to activate it also. It is also illegal to move the type of OEM version of WinXP liscensed to be installed on and Emachines computer on any other computer. It is called Piracy.
 

Read other 3 answers
RELEVANCY SCORE 51.6

My desktop computer's motherboard just died (had it confirmed by qualified tech people.) The computer was about four years old. It was a standard machine running XP home.

I am going to put together a new system, but someone mentioned that the new motherboards might not accept my old hard drive as the primary drive, which is a WD 40G drive. I can't believe this is true; won't a new motherboard just recognize it? That would save me the huge hassle of reinstalling everything....(as far as data, etc, I'm well backed-up in any case.)

Can anyone advise me on this?

thanks,
BJ
 

A:will my old hard drive be compatible with new motherboard?

Read other 9 answers
RELEVANCY SCORE 51.6

Hi everyone. I'm attempting to build a computer on my own. I've done minor things like switching video cards, upgrading processors, etc., but never started from scratch.

I've run into a problem, I think.

I purchased a Fujitsu 15k Ultra SCSI320 80pin hard drive. The connection doesn't match the one on my motherboard, Asus A8N SLI Deluxe.

Am I out of luck, or am I supposed to have an adapter of some sort? Sorry for the clueless questions. I'll try to supply as much information as required for an answer.

For information, I've only gotten to the "connect the parts" steps. Just got the motherboard in the case, and the processor and heat sink in place. Then I saw this problem and decided to come ask before I screwed something up.

Thanks in advance!
 

A:Hard Drive incompatible w/ Motherboard?

Read other 8 answers
RELEVANCY SCORE 51.6

I have a EP45-UD3L motherboard from Gigabyte. A few days ago I got some IDE to SATA cables to add some hard drives to my computer I already had one internal hard Drive hooked up with my current operating system on it. I wanted to hook up two more hard drives that I had from an old computer of mine. The first hard drive I tried to hook up was a Maxtor brand hard drive. I plugged it in booted up the computer and went to My Computer (Computer in Vista) the hard drive was not visible. So I tried hooking up the other hard drive I had witch was the main hard drive on my old compter a Sony VAIO. When I tried hooking that one up it tried to run Windows XP but could not. I did not know it would try to run Windows XP I just wanted to format it and use it as an extra hard drive. So I tried plugging my hard drive with Vista back in the motherboard. The motherboard won't recognize it at all no matter where I plug it in at. Strangely it does recognize the other two hard drives but the system disc won't boot up.
 

Read other answers
RELEVANCY SCORE 51.6

I have not been able to resolve a problem which has been affecting my computer for a few weeks now

please see below for my system spec

--------------------------------------------------------------------------------------------------------
Symptoms:
--------------------------------------------------------------------------------------------------------

hard drives are failing to show in windows (plugged in/set up)

computer hangs frequently on the very first boot "push x to enter bios" screen

"starting windows" screen while booting can take ~5 minutes

strange sounds from the hard drives when they are trying to load data
I had Windows 7 (upgraded from vista) installed on my 500GB sata hard drive for about 4 years and everything has worked flawlessly. Recently it started to "choke/crawl" on a pulse (every 10 seconds the computer would stop responding for 1 minute and then work normally again)

I decided to start fresh (for the first time in about 4 years) and installed Windows 7 64bit to my 2TB drive. It has worked flawlessly for about 4 days and now I am beginning to identify the same problems I had when the OS installation on the 500GB drive started to die (slow boot, some freezes, unable to see hard drives)
--------------------------------------------------------------------------------------------------------
Cause?
--------------------------------------------------------------------------------------------------------
Any... Read more

A:Want a challenge? ...is it the hard drive, the motherboard, or the PSU?

It could be the PSU beginning to break down, as the different results using different connectors of the power supply certainly raises questions as to the state of it.

However, then seeing the problem persists even when using a different PSU then makes you wonder if the issue is entirely unrelated to the PSU, and in fact something entirely different.

If it was me, and the motherboard was under warranty, my first port of call would be to RMA it, and get a replacement. I highly recommend you stick to Gigabyte, they make outstanding motherboards generally.
 

Read other 7 answers
RELEVANCY SCORE 51.6

I have a laptop and the motherboard is Dell 0rp6c8
How many internal hard drive can support ?

I used Speccy and it show that it has :
Slot PCI-E x16 "In use" and (5) Slots PCI there are (2) Available
does it mean I still can connect (2) hard drives ?

I would know the way to know that please !

A:How many hard drive can motherboard support ?

On a laptop you can only attach additional harddrives via USB or if you have a PCI-e slot. For the latter you need a PCI-e card - one like these:

Laptop Express Cards - Newegg.com

Read other 25 answers
RELEVANCY SCORE 51.6

Hi,

My motherboard is a DFI LanParty UT SLI-DR (details about the SATA-plugs can be seen here), and I'm currently looking for a new hard drive. The one I want to buy is the Seagate Barracuda 7200.11, with a capacity of 1,5 TB.

What I'd like to know is whether my motherboard can support a drive of this size?

I hope someone can help me.

Thanks in advance
 

Read other answers
RELEVANCY SCORE 51.6

Hey all,
I just built the machine below last night, and have encountered a problem.
I just got a Gigabyte GA-8INXP P4 Titan 667 Motherboard, which has 4 IDE connectors, 2 of which are RAID. I also have an ATA133 Maxtor hard drive, and simply want to connect it, on its own, to one of the RAID connectors, to utilise the ATA133 capabilities of the Hard Drive, as the other 2 IDE connectors on the Motherboard only support up to ATA100, according to the manual. Can this be done? The Promise RAID manual only talks of installing 2 Hard Drives on the RAID connectors.
I have connected the Hard Drive to one of the RAID connectors - IDE3,
yet when I boot up past the BIOS screen, "Verifying Pool Data" appears, and it just hangs there.
If I try and install Windows XP, the Windows setup tells me that there is no Hard Drive installed, yet the Hard Drive appears on boot as "Maxtor Ultra DMA 6". Do I have to change something in the BIOS, like the "RAID Controller Function", because I changed this from ATA to RAID and back a few times, yet still nothing.
I say all this, because in the manual, the specifications state that the RAID IDE connectors support "RAID, Ultra ATA133/100, EIDE".
Any help much appreciated.

 

A:Connecting Hard Drive to Motherboard

Did you install the drivers for it? Did you press f6 at the prompt to let XP know you have an extra driver disk?
 

Read other 3 answers
RELEVANCY SCORE 51.6

Quote from my friends problem
recently removed my computer drives - master and slave- when i went on holiday. I put the system back in order and recently noticed my slave drive has not shown up in "My Computer" list. I tried swapping the ribbon cables with no changes. So i swapped the position of both drives in case it was the power cable. Both are SATA so they use the same power cable. But still no changes. I removed the slave drive (F Drive) and placed it into an external caddie and booted up. It started to install driver for it and is running fine from there.

So after that, i re installed it into the PC and still no change. It simply does not exist. I have run the boot set up on startup and it is not listed there. It is simply a ghost to the PC.

Any ideas what it could be or how i could sort this issue out?

Also, in hardware profiles under show hidden drives, it is listed and clicking this states it is not connected.
Is there any solution that would help my friend solve his problem
N.B: please take that internal hard drive, instead of slave ...

A:Is it motherboard or hard drive or bios , which is the cause of this

Quote:
recently removed my computer drives - master and slave

Both are SATA


There's some confusion from the start. There is no such thing as master and slave with SATA drives! Master and slave drives come from the old technology, EIDE (PATA) drives where you could have two drives attached to one "data" cable and one motherboard connector. With two drives on one data cable, there needed to be a way for the system to keep track of the drives, so one drive was designated as master, the other as slave. And this was determined by a jumper on the back of the drive and where on the cable the drive was connected.

But with SATA drives there is only one drive per data cable. Every drive has it own data cable and motherboard connector. So no master or slave designation is needed.

You can have more than one drive on a power cable with SATA, but that has nothing to do with master and slave - as again, no such thing with SATA drives.

The boot drive is determined by the boot order set in the BIOS.

Read other 9 answers
RELEVANCY SCORE 51.6

Hi, can anyone advise me please with regard to the following epic story?I have an Acer Aspir 6935g, which came out of the box with windows vista ultimate 32 bit pre-installed. I bought it eight year ago approximately. When Microsoft released windows 8 and it was on special offer for the first three or six months, can't remember exactly how long. I went to CurrysPcWorld and purchased windows 8 Pro, whic cost me 50 pounds sterling. In the package was a 32 bit & a 64 it DVD. seeing as my machine is compatible for installing 64 bit, I decided to install 64 bit. My original hard drive had three partitions. PQService partition, whatever that is, I don't understand. A "D" partition with windows vista 32 bit, which i presume is your recovery partiton and "C" partition which had windows vista 32 bit installed on it. I inserted the 64 bit DVD., got into auto install, on the upgrade or custom install, I clicked the custom and then I clicked on the "D" partition and I either deleted it or formatted the "D" partition and merged it into one with the "C" partition, so that left me with only PQService and a "C" partion. Before I go any further, the windows 8 I purchased is not an OEM., which I believe is tied to the motherboard you install it to. I then did the clean install of windows8 Pro 64 bit, which went ok. I then got notificaation to upgrade from Microsoft to windows 8.1, which I did and was successful. I then got notification to upgrade to windows 10 Pro., which although Acer did... Read more

Read other answers
RELEVANCY SCORE 51.6

I have just bought a new motherboard/processor and had it put into a new case with a better PSU (given that my older system died recently ).I deliberately didn't get a new hard drive.
I intend to put my old ram and graphics cards on the new motherboard (they are compatible).
My question is - can I simply attach the old hard drive from my older computer with my operating system (XP) and files settings etc and expect there to be no conflicts when it boots up .?
 

A:Adding old hard drive to new motherboard.

Hi ohisay, and welcome to TSG.

Unless your new motherboard, BIOS and CPU are just about identical drop in replacements for the original parts, you will most likely have problems with hardware driver conflicts and getting Windows XP to run. If your PC came with an OEM version of Windows XP, I believe that the Microsoft license ties it to that that specific motherboard.
 

Read other 1 answers
RELEVANCY SCORE 51.6

I Have about a 3+/- year old Compaq
Win XP Home SP1
AMD Athlon XP 1600+
Maxtor 40GB Hard drive (original)
MSI motherboard [(new) reason; apon turning on the system would get "System board failure" message nothing else]
The hard drive is seen in the BIOS and in the first post screen but will not boot. I hooked up one of my old hard drives with 98SE on it and booted right up. Slaved the old hard drive off the 98SE hard drive. Both show in BIOS and post but only the 98SE shows in "My Computer"
Have yet to check old motherboard with 98SE hard drive to see if it is bad or the hard drive caused the problem.
What are the chances that the motherboard took out the hard drive or vise versa?
Everything was original before I changed the motherboard.
Thanks in advance for any help.
GrandPops
 

A:Motherboard/Hard drive problem

It's possible. but more likely that you need to do a repair install so that the old XP system ( I guess? ) can start up on the new board. . . what message do you get when you try to start it?

wrs
 

Read other 2 answers
RELEVANCY SCORE 51.6

Good Evening, I have a Dell Inspiron 15r 5520 intel core i5 6GB Memory originally with a built in Microsoft Windows 8.

Purchased in 2012
It has since been updated to Windows 8.1 and Windows 10. 
I upgraded to Windows 10 as soon as I found out Windows 10 was free for people who had Windows 8
Windows 10 was working fine until July and then that's when the Motherboard 'gave out'
I tested it and it said the Motherboard is fine it's just the HDD.
Well the Hard Drive and Motherboard overheated and both died.

I have replaced a Heat Sink AND Fan to attempt to save it (Yes, I used a rice size amount of Thermal Paste to reinstall)
So now I purchased a New 1TB (1000GB) 8MB Cache 5400RPM SATA 2.5" 9.5mm Notebook Hard Drive and that was fine.
I also purchased a replacement Motherboard for my Laptop, which came with no Software, leading me to purchase Microsoft Windows 10 Pro.
I have had trouble downloading the Windows 10 pro, as it would turn off during download and refuse to actually go on and give me the proper download for a while.
After 2 days of trying, I finally realized I had to remove the CD once it was installed, and Windows 10 Pro was installed on my computer. After a few downloads, Skype, Google Hangouts and Roblox(Online game) to be exact, the motherboard fried out.
I recently got a Motherboard on ebay from China and now I am trying a USA seller instead.

Is Windows 10 Pro frying my Laptop? I know I cannot download devices from Dell any l... Read more

Read other answers
RELEVANCY SCORE 51.6

Hi
I purchased a foxconn mother board bundle into which I intended to place my old hard drive cd rom, cd writer and dvd writer in.
I first formated my hard drive while it was in my old machine, then placed it along with my cd rom into the new case and instaled windows X/P.
I then went on to place my cd and dvd writers into the new machine one as master the other as slave, I also slaved the cd rom off to the hard drive. When I rebooted the machine windows would not recognise my hard drive I disconnected both slaves setting the hard drive back to master but only the cd writer is being reconised in post and the bios.
 

A:New motherboard old hard drive problem

Read other 9 answers
RELEVANCY SCORE 51.6

I am looking to upgrade my motherboard, but keep my current hard drive and the content on it (due to having alot of programs and software plugins on it). I am running Windows 7 32 bit with and AMD Phenom II x2 CPU. My current motherboard is one I went to when my compaq desktop died a while ago and I wanted to upgrade my operating system and hard drive capacity anyway. So, the first link below is the motherboard I have and the second link is the motherboard I am looking at upgrading to (since the two are somewhat comparable in specs/give or take a few things). Any suggestions or help is welcome. Thanks!

1) My current motherboard
http://www.newegg.com/Product/Product.aspx?Item=N82E16813135246

2) Motherboard I am looking to purchase
http://www.newegg.com/Product/Product.aspx?Item=N82E16813128394
 

A:Change Motherboard/Keep Old Hard Drive

Read other 7 answers
RELEVANCY SCORE 51.6

Hi, I have a 1TB Hard drive in my HP ENVY 15t-j100 Quad Edition CTO Notebook PC and I would like to upgrade to a M.2 SSD.  I looked at the service manual here: http://h10032.www1.hp.com/ctg/Manual/c03943414 Can this really only support 24GB mSATA SSD? Do I have any better options? I checked and I have a hp 1963 (ue31) motherboard. I couldn't find documentation on the motherboard to see if it was compatiable. Can someone help me?Thanks. 

A:Want to upgrade Hard Drive to M.2 SSD. Is my motherboard com...

An M.2 SSD is not compatible with your notebook. There is no M.2 slot on the systemboard to plug it into.

Read other 1 answers
RELEVANCY SCORE 51.6

Hi all,

I was wondering if you could provide me with some feedback on a hard drive issue that started when I booted up my pc yesterday. Hard Drive is WD 160GB SATA.

I received this error at boot up:

Read Disk Error CTRL+ALT+DEL to restart

I restarted and luckily I was able to get to the desktop (took longer then normal tho).
Checked Event Viewer.. nothing showed. Checked Performance Logs... no errors showed.

Decided to double check all the connections... all plugged in nice and secure. Rebooted. Got the Read Disk Error again. this time it took me 3x to get to desktop. I decided to try another SATA connection on motherboard. REbooted.... got error again.

I ran a chkdsk/r and when system rebooted the Read Disk error showed up again.
After another 3 ctrl+alt+del reboots... I was able to get into Windows. I downloaded the Diagnostic Tools from WD and my drive failed both the Quick and Extended Tests. Not surprising lol

Anyhoo, here is a screenshot of my WD Diagnostic test results. I was wondering if it was a HDD issue or a motherboard issue? Any thoughts? I would rather replace a HDD then a motherboard. This WD 160 SATA drive is less then a month old also. BIOS sees the hard drive.also tried setting BIOS back to default.... sometimes that works but not this time tho :-(

I think I am living on borrowed time with this HD but before I replace I wanted to get more opnions.

Thx for the input

A:WD Hard Drive Failure or Motherboard?

Did you create the bootable CD ? ?
The results are more accurate then running it inside Windows.
Also you should be running the Long test.

Read other 9 answers
RELEVANCY SCORE 51.6

Just got a new board/memoru/cpu. and our old hard drive does not like it. we get a blue scree...

i know formatting and re-installing xp would be a soulution, but a hassle.

we are looking for a way to avoid formatting.

llemee kno soon
thanks
 

A:new motherboard/cpu/ram, old hard drive doesnt like it

Read other 6 answers
RELEVANCY SCORE 51.6

I just bought an AMD XP1700 board and a new atx case. In my old machine, I had a 40gb hd for primary, and a 20 gb for a slave. Now, my 40 Gig drive is not being read by the new board. Fdisk won't partition it or format it. I can't install anything on it, and the machine wouldn't boot off of it when I still had my OS on it. My old machine reads it fine, and the new board reads by 20 Gig drive fine. I installed Windows 98se on it, installed partition magic 7.0 and tried to partition the bigger drive from there, but its still not working. HELP!!!!
 

A:Hard Drive problem w/ new motherboard

Read other 16 answers
RELEVANCY SCORE 51.6

This is what I want to do.Transfer everything from my ide on my computer to a sata drive on my computer and then use it in a new computer that I"m building.I had to slow down the drive to sata1 to get it to work in old computer.Drives are maxtor ide and Western Digital sata 2.I have both softwares.Running win xp pro all updates applied.Any help is going to be appreciated.
TIA,Allenv
 

A:Changing Hard drive and motherboard

You can transfer files and data but you will need to install Windows clean on new build...fine to have files and data on the drive in a separate partition so you do not format the whole drive by accident and lose everything, or use sata drive for clean install and then jumper the ide drive as slave and use whatever you want from it in new build.
 

Read other 2 answers
RELEVANCY SCORE 51.6

I'm thinking of buying a new hard drive and want to make sure my motherboard will support it.
I have a ECS K7S5A MoBo and I'm looking a buying a :

Hitachi Deskstar 7K80 80GB Hard Drive (Serial ATA II, 7200, 8MB)
Interface: SATA II (Serial ATA II)
Interface Type: Serial ATA - 7 pin
Rotational Speed: 7200 RPM
Cache Size: 8 MB
Maximum Transfer Rate: 3 Gbps
Access Time: 8.8 ms

Any help would be appreciated.
I just don't want to have to return it.

Thanks,

Rob
 

A:Motherboard Hard Drive Compatability...

Read other 6 answers