Over 1 million tech questions and answers.

ThinkCentre: Stuck at Lenovo splash screen after lenovo solution bios upgrade

Q: ThinkCentre: Stuck at Lenovo splash screen after lenovo solution bios upgrade

Hey folks,

Got an M93 with Win 10. Lenovo solution center asks to do upgrades on BIOS and a bunch of drivers. Did that, and now I can't boot the computer.

Tried pressing F1 after pressing start button, no help. Can't enter BIOS, still stuck at lenovo screen. Also tried Ctrl+Alt+Del on that screen, blacks out then stuck at lenovo screen again.

Please help and inform, thanks!!!

James

Mod: edit Subject line with system type













Solved!

Go to Solution.

RELEVANCY SCORE 200
Preferred Solution: ThinkCentre: Stuck at Lenovo splash screen after lenovo solution bios upgrade

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: ThinkCentre: Stuck at Lenovo splash screen after lenovo solution bios upgrade

I would try resetting the BIOS using the jumper, or by taking out the CMOS battery, wait a minute or two, and then replace it and try booting up. See page 73 of the Hardware Maintenance Manaul linked below for location of the Clear CMOS/Recovery jumper (# 20) https://download.lenovo.com/pccbbs/thinkcentre_pdf/m83m93p_hmm.pdf Clearing the CMOS (BIOS)1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. 3. Locate the Clear CMOS /Recovery jumper on the system board. 4. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin 3). 5. Reinstall the computer cover and connect the power cord. 6. Turn on the computer and leave it on for approximately 10 seconds. Then, turn off the computer by holding the power switch for approximately five seconds. 7. Repeat step 1 through step 2. 8. Move the Clear CMOS /Recovery jumper back to the standard position (pin 1 and pin 2). 9. Reinstall the computer cover and connect the power cord. Good Luck,

Read other 6 answers
RELEVANCY SCORE 172.4

Hey folks, Got an M93 with Win 10. Lenovo solution center asks to do upgrades on BIOS and a bunch of drivers. Did that, and now I can't boot the computer.  Tried pressing F1 after pressing start button, no help. Can't enter BIOS, still stuck at lenovo screen. Also tried Ctrl+Alt+Del on that screen, blacks out then stuck at lenovo screen again.  Please help and inform, thanks!!! James

Read other answers
RELEVANCY SCORE 119.2

Hey all,

I have recently decided to restore my laptop back to factory settings for various reasons.

The factory settings on the recovery partition mean returning to Windows 8.1 and then upgrading back to Windows 10.

I have no problem returning to Windows 8.1 but when I use the Windows Media Creation tool to download Windows 10 and install something happens.

I start the installation where it says the computer will restart several times, but during one of the restarts it gets stuck at the Lenovo splash screen.

I have since run restore to get back to 8.1 a couple of times just in case there was a problem there but still the same problem happens when trying to upgrade to 10.

I have had no problem returning to 8.1 and then upgrading to 10 in the past.

I'm not sure what kind of information you'll need from me so request and I will let you know.

Any help would be greatly appreciated!

Mark

A:Windows 10 Upgrade - Installation stuck at Lenovo splash screen

I forgot to add:
After it has been onthat screen for a couple of hours I decide to hold the power button down on the laptop to force it to turn off.
After that it restores 8.1 automatically and presents this error:

We couldn't install Windows 10
We've set your PC back to the way it was right before you started installing Windows 10.

0xC1900101 - 0x3000D
The installation failed in the FIRST_BOOT phase with an error during MIGRATE_DATA operation

Other posts in this Forum have stated that antivirus could be the problem and removing it has solved the problem for other users, however, mine is a wipe and return to factory and I have uninstalled that awful McAfee that comes with Lenovo.

Read other 1 answers
RELEVANCY SCORE 114.8

after blue screen of death, my lenovo is not booting, its stuck on the brand name logo and there is nothing i can do i tried remove the battery, and power up with jus cord and opposite, tried to push one key recovery but that dosent work neither any ideas?OS. win10 x64pentium 2.4ghz6gb ram1tb hddintel 5500 graphics

A:Lenovo G500 stuck at "lenovo splash screen"

The first thing I look at if a machine hangs at startup is the USB ports.  Physical damage can create shorts which cause these symptoms.  Check for bent pins or a tongue broken off.

Read other 3 answers
RELEVANCY SCORE 114.8

Okay, so my Lenovo N580 IdeaPad with i3 processor is stuck at the splash screen, aka the black screen with Lenovo written on it in bold white letters. I tried removing the battery, then putting it back on, then pressing power button for 45 secs. I also tried pressing the the Novo button (the small round and black button besides the power button) but the screen shows no change and does not go to bios/reset menu on pressing f9/f12 too. What else can I do to get my laptop back on? Please help, all my project work is on my laptop










Solved!
Go to Solution.

A:Lenovo N580 stuck at "Lenovo splash screen"

Dear CPVirani, Welcome in lenovo community, Please try to : 1- Remove the battery and the charger >> Hold on the power button for 20 seconds.2-Connect the charger only >> Hold on the power button for 10 seconds.3-Try to turn on the laptop. Regards,Joseph

Read other 5 answers
RELEVANCY SCORE 114.8

I have a Lenovo G500 Laptop with core I3 and 2 gigs of ram and Windows10 updated OS.Recently it has started to get stuck on the starting LENOVO screen. Laptop gets started when i remove the battery connect it with a charger, but when i again switch it off and then turn it on again, It again gets stuck on the Lenovo screen. I want a permanent solution for it. PLease help me!

Read other answers
RELEVANCY SCORE 114.8

HiI have Lenovo g500 core i7 ram6 ati radeon 8750 1tb hdd. It's been like a month that laptop freezes at the splash screen. I live in Iran and the laptop is made in China.I've searched the forums and found the "battery removing, 15sec button-holding and AC Adopter pluging" solution and it worked ...but today it's not working anymore ... I'm stuck at the splash screen for 4 hours and this is our desktop pc I'm using to post this message.I really need my laptop! It's my life!Please help ...










Solved!
Go to Solution.

A:Lenovo G500 stuck at "lenovo splash screen"

Hi Azadkv,
 
Welcome to Lenovo Community!
 
I?m sorry to hear that your G500 Laptop is not booting to Windows and hanging at Lenovo Logo and the issue persists even after performing Flee-Power step. Hence, I suggest to perform BIOS reset and check if the issue persists. Below are the steps to perform BIOS reset:
 

To access BIOS menu turn OFF the Laptop and press the NOVO button located beside power button.
Then to reset the BIOS to its defaults click on ?F9? Key and select YES.
Now click on ?F10? Key to save the changes that are done in BIOS, the computer will automatically restart.

Do post us back if the issue persists.
 
Best Regards

Shiva Kumar




Did someone help you today? Press the star on the left to thank them with a Kudo!If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.Follow @LenovoForums on Twitter!

Read other 9 answers
RELEVANCY SCORE 112.8

To make a long story short, I've been asked to help fix a friends mom's U410 laptop which wasnt activiting Windows 8.1 properly (Was Windows 8 OOB). After struggling with the activation for a few hours, I backed up the data and decided to just run the Lenovo one key recovery. During the recovery process, the installation had failed. When I attemped to reboot, no Lenovo splash screen was loading - just a black screen (although i can hear the cooling fan start, and hear the harddrive spin up. I tried to access the boot menu thru the novo button, and nothing would load; still a black screen. After researching for a few more hours, I had found multiple threads about bios updates required to be able to access bios with windows 8, and other threads about gpus on these units booting to a second screen (which i did test, and the second monitor does indicate a signal). None of the solutions on those threads have given positive results.   Basically, I've run out of options and am looking for some suggestions. The only thing that shows up on the display at anytime is the small blue novo menu when the button is pressed (normal start up, bios setup, boot menu, system recovery - all of which just leave a black screen). Thanks.

Read other answers
RELEVANCY SCORE 112.8

Hi to all, i have a lenovo s20-30 here with the problem on boot up process.. when i turn power on it just hang on lenovo and a circle loading in a very slow process..I tried :1. Removing HDD and put it back on.2. Unpluging cmos battery,3.reformating4. updating drivers5. check bios, reset to default settings... still not fixing the problem.. it takes an hour before booting into system...one more thing is, when i press power button the monitor just stay black no display at all.. i need to unplug battery and put it back on then power it on,, it will take 5 times before the screen displays..

Read other answers
RELEVANCY SCORE 112.8

Hi everyone i have a lenovo Z50 intel i7 16gb ram 1tb hard drive, here is my problem everytime that i turn on the computer for the first time gets stuck in the lenovo logo, however if i turn it off and turn in on again it will start normally. I want to be able to start my laptop in the first attemp, anyone could help me, i already try everything reset the computer, reinstal windows, refresh the computer, removing the ram removing the hard drive and nothing works.. Please help
 
Mod's Edit: Updated Subject line and moved post to the Lenovo Z series notebook forum.
 

Read other answers
RELEVANCY SCORE 110.8

Yesterday I did a routine restart and when rebooting my E32 SFF it got hung up on the Lenovo Logo splash display and didn't load windows. The operatiing system is Windows 10 64 bit. Thinking it might be a hard drive problem, I had at the time a 500GB SSD installed which had been cloned from the original 180GB SSD that came with the computer. I swapped the 500GB drive with the original 180GB drive but the problem still persists which leads me to believe it's not a hard drive or Windows issue. Any suggestions would be appreciated. The fans power up and the led indicators as well as the USB ports, so I'm doubting a power supply problem. I have a Windows 10 repair disc but it won't boot on the disc as I believe the bios is set up to boot on the hard drive only. Is this a motherboard problem?

Read other answers
RELEVANCY SCORE 105.2

Updating Windows 10 (I think to 1607), there were a number of restarts.Now the laptop is stuck at the Lonovo splash screen.Any suggestions on what to do? Thanks [Type: 20DQ-001KUS]

Read other answers
RELEVANCY SCORE 104.4

SERIOUSLY LENOVO YOUR UPDATES ARE NOT GREAT,its done something to the BIOS.My desktop Lenovo 93m (i think thats the model... )Its stuck at the screen and to make it worse i cannot even access biosI pressing f2 or f1 or f12 cause thats the way is it not?It updated the other day and now just stuck at lenovo screen, i have removed hdd attempted booting and disk drive. Any solutions?It happen a few days ago, it updated from lenovo centre application.Am i doing the right thing to get into bios? Any solutions? Cause if i get into bios i can wipe the hdd and put a back up in.Please any help would be great!i have number of lenovo pcs and i have set them to not update.

Read other answers
RELEVANCY SCORE 104.4

Hello. Can someone help me please. My lenovo G580 laptop is stuck on the lenovo splash screen and I do not know how to fix it.

Read other answers
RELEVANCY SCORE 104.4

I have a Lenovo G500s that is stuck on the splash screen when I turn it on. It's done this once before and I was able to get it to work by taking the battery out and turning on the laptop while plugged into the ac adapter, this method is not working this go around... help? 

A:Lenovo G500s stuck on splash screen

And I've tried to access the BIOS system and it will not let me

Read other 1 answers
RELEVANCY SCORE 104.4

Hi everyone. I've got a big problem with my laptop. I will explain the whole situation.  I recently upgrade my laptop with a Samsung Evo ssd and a 8 Gb ram ddr3 1600. At the beginning everything was fine but then, sometimes I got screen problems (like flickering) and windows 10 crashed. Now the biggest problem : my laptop is stuck at lenovo logo with loading dots. Even if I try to load USB windows tool (to install new os) it doesn't work. I also tried to install Ubuntu unsuccessfully. I searched on the web all the possible solutions. I temporary removed the battery, ac adapter and hold the power button for 30 secs, but nothing. I also read to remove the cmos battery but I can't locate it in my IdeaPad z500. I also searched on the hardware maintainance pdf but there is nothing about that. I also removed ssd and new ram  with old components but it's still the same. I don't know what to do know, please help me!! I hope I didn't screw my laptop 

Read other answers
RELEVANCY SCORE 104.4

Hi I am new to this community, so I would like to applogise if I mist a simillar subject (I did check some but non resolved my problem). I have a thinkpad t420, I bought a used one. It worked great, and I bought it from a friend, that I trust. I installed a ssd drive, was usnig Linux, and everything worked for one month. But then I bought a HDD caddy, and replaced the CD rom. After that my thinkpad worked for a day (although it didnt recognize the second HDD). The next day I tried searching BIOS for some settings, and after restarting my laptop it was stuck on Lenovo splash screen, rebooting in a loop. I tried:- removing and replacing the caddy with the CD rom,- replacing my SSD drive,- replacing RAM (both slots),- reseting BIOS,- running a diagnostic CD (but it will not boot, neither can I boot from an USB) My google search showed that it could bi a problem with one of the USB pins inside of one of the ports (short circuit or something like that), but I could not finde any damage. So I am thinkig that the motherboard could be damaged, but I can access BIOS, but that is the only thing I can do with it. I would be wery thenkful for any advice or help, before I go to an official Lenovo service for help. Thnak you! Z.













Solved!

Go to Solution.

A:T420 stuck on Lenovo splash screen

Hi Zjaz123456,
 
Welcome to Lenovo Community!
 
As per the query we understood that you are facing issue with not booting to OS on your ThinkPad T420.
Is both HDD &SSD detecting in BIOS?
 
Check with removing CMOS battery, make sure you have disconnected the system from AC adapter and battery is removed.
 
Remove both the drive & battery from the system, disconnect the power adapter. Press and hold the power button for 15 to 20 sec perform this step for 2 to 3 times and then connect only the drive which is having OS installed in it. Use only power adapter to switch ON the system.
 
Hope this helps. Do post us back for further assistance!
 
Best regards,
Hemanth Kumar





Did someone help you today? Press the star on the left to thank them with a Kudo!If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.Follow @LenovoForums on Twitter!

Read other 9 answers
RELEVANCY SCORE 104.4

I'm trying to repair this machine for my nephew. When I turn it on, it never moves past the Lenovo splash screen. I tried the NOVO button, but it just goes to the same Lenovo screen, and just cycles off again after about 5 seconds. I don't know that much about Lenovo laptops. I've tried pushing the F2, F12, FN+F2, FN+F12 to no avail. I can't get to any BIOS options, or boot it through a boot CD. Any help will be appreciated.    Thanks!

Read other answers
RELEVANCY SCORE 103.2

Hello folks,  I seem to be having some issue with installing Windows 10. I found the Lenovo Upgrade Checklist and followed the steps point for point. (https://support.lenovo.com/gb/en/solutions/ht104203) After downloading the update, it requested a restart and booted up into the update screen. The update got to around 20% and restarted as noted on the update screen.  Once again I'm presented with the Lenovo boot screen but this time it doesn't seem to be progressing, nothing has changed for the last 50 minutes and counting. What was other people's experience through the upgrade? Should I be prepared for a longer wait or is this abnormal to the process? Thanks for taking the time to read! 

Read other answers
RELEVANCY SCORE 103.2

Good afternoon!  I am am wondering if anyone knows approximately how long the TPM update takes for the Lenovo T470? It is stuck on the Lenovo screen and has been for at least 30 minutes. It said it would finish update with BIOS but no it?s not doing anything, that I can see.  Any thoughts?

Read other answers
RELEVANCY SCORE 103.2

Hello! I have done some snooping around, but can't find anything that explivitly solves the problem I have been having. When my P50 is plugged in at my desk (eg. Monitor, Ethernet, Keyboard, Audio Out, Power), and it has shut down / hybernated when I turn it back on it will stick at the LENOVO splash screen (looks to me like it locks up because it won't even let me into advanced boot options).  Temperary Solution: Problem seems to resolve with removal of battery, hold power button, plug in AC, boot with only AC power. (Sometimes this takes several attempts). Thinking about just setting shut down time to forever to avoid altogether.  Causes: I suspect it has something to do with my monitor (just a cheap ASUS off of Amazon), it is not a repeatable problem either, it only happens off a total cold start and maybe only 1/5 times at that.  Other: BIOS Version 1.52  Any opinions are welcome    -P50-Engineering

Read other answers
RELEVANCY SCORE 102.8

Hello thereI tried to do a full reset of my m700 with Windows 10 and reached to the black screen where the options to do tpm clean F12 or ESC. The keyboard is on the right usb that shows the keyboard sign and tried the HDMI AND D-SUB as well all no luck. However I cannot hit anything with my keyboard  Tried to press F1 F2 F12 ESC OR ENTER no luckAny idea would be helpful Thanks 

Read other answers
RELEVANCY SCORE 102.8

Hello there I have tried to do a full reset of my m700 with Windows 10 and at the end I got the black screen where to clear using F12 or ESC. The problem is I can't press anything on my keyboard. It connected to the right usb that shows the keyboard sign. Tried to hit F1 F2 F12 ESC OR ENTER with no luckAny idea would be helpful Thanks 

Read other answers
RELEVANCY SCORE 100.8

Purchased new from Best buy in May 2017.  All has worked perfectly until now.  Left my computer for a while while it did some Win10 updates and come back and the Lenovo splash screen is on the screen.  Will not go past that.  I can shut it down by holding the power button but when restated the keyboard lights up and the splash screen comes up and that is it. I have tried pushing the little recovery button while the laptop was off and it does the same thing as the power button and sticks at the splash screen.  $1800 door stop!!! Anyone got any suggestions

Read other answers
RELEVANCY SCORE 95.6

Hi guys So i recently ran into a problem, when i try to boot my laptop it will hang at the lenovo splash screen and it will be like that for a long time if i dont turn it off. I tried disconnecting main battery and bios battery, it did help but when i shut it down for like 3 hours came back and turned it on back again it was stuck at splash screen again. I also noticed that when it stuck during boot and i shut it down from the power button and turn the laptop on again its booting normally. Also tried removing all usb devices and booting the laptop and it still does the same hangs at the splash screen. Please guys help. Best regards Gerard

Read other answers
RELEVANCY SCORE 95.6

I have been having this issue for the past year, roughly. When booting up, my screen takes forever to turn on and display the Lenovo splash screen, sometimes over a minute. I have done the following:Tested HDDReseat RAMReinstalled windowsTried to update to the latest BIOS (from 1.17 to 1.21) This provided an Invalid Firmware Image!!! Error.It seems to happen less without the charger plugged in.Idk what the issue could be, I am running Windows 10, I have tried it on Windows 8, no matter what I do it is slow to boot to the splash screen. 

Read other answers
RELEVANCY SCORE 90.8

Hi,i have Lenovo ThinkPad T470 (LENOVO 20HD0002MC) and recently has started a strange problem:While booting at first Lenovo logo shows up (where you can get to BIOS by Enter key) and right after screen goes black. When i power down laptop and boot again (sometime few times) intead of the black screen there is a prompt for Bios password, like it should have and booting continues to OS.Enter key for BIOS doesnt work while it slill get stuck on black screen just right before it loads the BIOS (after trying few times with power -off/on it gets to BIOS and i can boot normally)I have BIOS firmware updated to the latest version, so as well drivers for hardware.Im not aware of any change that could potentionally start this issue, maybe after updating bios to some newer version.Otherwise im using Windows 10 with latest updates, but i dont think this could cause the issue as its way before windows loading.Thanks for the help.

Read other answers
RELEVANCY SCORE 88.8

Hello, I have a Lenovo ThinkCentre M58 small form PC. I would like to install a better graphics card into the PCI Express slot. Logic would dictate I need a better PSU than the standard 280 or 240 watt PSU that comes with the system. Were can I purchase a more powerful, small or low profile PSU for this system? Any help woud be appreciated. Not looking for gaming use, just more power in the PSU for possible dual monitor use, better display, and power/stability for a 1/2GB GPU card. Thank you, Peter Costa

Read other answers
RELEVANCY SCORE 88.8

What is the cheapest 300W+ PSU that will fit in this machine? I want a gpu but that 240W PSU won't cut it. EDIT: Here is the gpu i am planning on buying. https://www.newegg.com/Product/Product.aspx?Item=N82E16814932005&ignorebbr=1

A:Lenovo ThinkCentre M81 PSU Upgrade?

Tower or Small form factor... actually posting your Machine Type Model (MTM) would help. If you have the tower, just about any ATX PSU like this one would work since I believe your motherboard as the standard 24 pin connector, but with that card you might want to wait to see if it even needs a 300w PSU, because it may work just fine with you current PSU unless you have a bunch of HDDs installed etc.. If you want a Lenovo PSU that shipped with the M81, you can get a 280 watt like this one  https://www.amazon.com/Genuine-Lenovo-41A9684-Desktop-PS-5281-7VR/dp/B00R3NPNN6, which should be more than capable of powering your GPU. Best of luck,      

Read other 1 answers
RELEVANCY SCORE 88.4

My S1 Yoga, 20CD-00B1US, is stuck with the screen off and the power LED stuck on. When I try to push or hold the power button it beeps two short beeps and the LED stays solid. I was running the Lenovo Bios Update Software directly from their site. The power cord was plugged in and no other programs were running (aside from background programs). Now it is just stuck like this. Any thoughts or help would be great. I can't even get it to force shut off. Thank you in advance!

Read other answers
RELEVANCY SCORE 88.4

My Y50-70 Touch has been sitting in my drawer for over a month now since i only use it for school. I start school tomorrow so i decided to start it up and charge it but it gets stuck on the loading screen with the spinning circle after the lenovo logo pops up. Its been on the booting screen for over 3 hours and wont turn on. Help please!

A:Lenovo Y50-70 Touch stuck on lenovo booting screen

Ive tried resetting the pc, start up repair, system restore and none of them are working. i get errors

Read other 1 answers
RELEVANCY SCORE 88.4

My g580 ran out of battery while using it, and now it gets stuck on the lenovo logo. I tried a different hard drive which changed nothing, I've tested both hard drives on a different computer and they both work. However when I boot the laptop with no harddrive it will get past the logo go to a screen saying something about an unplugged cable then reset and get stuck on a blank screen.   If I plug in my windows recovery usb drive( and no harddrive) the the machine will boot normally and go to the windows installation screen. So any ideas on why a working harddrive would stop the system from booting? Also I've tried the whole taking out the battery unplugging it holding down the power key and then plugging it back in thing, did nothing. 

Read other answers
RELEVANCY SCORE 87.6

Hello i have Lenovo Thinkcentre M90P whith Intel Pentium G6950 250GB HD  and 2GB of 1066mhz DDR3 RAM i think its Hynix? Recently i bought a 4GB Crucial DDR3 stick 1600mhz  . http://www.crucial.com/usa/en/ct51264ba160b  I took out the old RAM and put in this new one but the PC doesnt get into windows anymore and just keep rebooting if I install the old RAM back everything works perfect. I tought that MHZ shouldnt be a problem and that the new ram will be downgraded to 1333mhz (max supported i think). Maybe any BIOS update would work or what should i do?  Thanks for help!

Read other answers
RELEVANCY SCORE 87.6

I am trying to update the Uefi/ bios for a Lenovo Thinkcentre M82.  I created a CD with the files and followed the instructions.  The instructions say to reboot the computer with the CD in the drive.  I do this.  However, the computer boots normally to Windows. Since I have never flashed a UEFI/ bios before, I would like to understand a little more about what's actually involved.  Is part of the process to have a bootable CD and boot to it?  Or are we just using the files that are on the CD? If I have to get into the uefi bios and initiate the process through a screen in there, I don't seem to be able to get in there, for some reason.  I tried F1, F2, F10, F12, and enter (each on separate boots).  I also tried to initiate the process through Windows (there is a choice "updated UEFI firmware").

Read other answers
RELEVANCY SCORE 86.8

Hi everybody, I saw many of problems like mine there, but I can't still do anything after several attempts to solve that.  It started two weeks ago.. I did cleaned my hdd, then to keep my device lil a bit update I have updated few drivers. First day, it was able to boot up after 10-15 attempts. (Holding down the power button, disc. battery, ac, reconnect and power button again). Since that time I was unable to get to the BIOS, set Boot order, and I couldn't see even the splash screen. Several days it did the same and the attempts grew up.  Last time it was able to launch, its about 4 days ago, I was watching, film then I felt asleep. When I woke up in the morning, the screen wasn't black but still slighty light(not off, fans were working, cooler was fine). Since that moment I couldn't boot it anymore. I tried reseting CMOS battery, tried to flash bios by using flash disk and Fn+R (laptop did different thing but after 15secs it has turned off).. I think it is frozen BIOS but I haven't clue what to do when I can't simply set the boot order.  Maybe I am wrong and the problem is only in the motherboard. Novo button works but everything I choose there, it ending by black screen again.  Thanks for help, maybe for any solutions how to fix this. I am prepared to buy another motherboard, but if I would be able to repair it on my own, I would happy. Thanks,Jakub.

A:Lenovo Z580 no splash, no BIOS, no Boot

REPAIR!




Did someone help you today? Press the star on the left to thank them with a Kudo! I dont know what Kudo does but anyway xDThere is nothing like 192.168.1.1

Read other 1 answers
RELEVANCY SCORE 86.4

All,
I have a Lenovo ThinkCentre M57 6072-AUF running Windows 7 64 bit. I got it for a song at a computer recycle center? It was originally a govt of Quebec system and the BIOS is in French. I want to flash the BIOS to update it and to also convert it to English. I went to the Lenovo site and burned the correct BIOS .iso to a disk. The old BIOS version is ?LENOVO 2RKT38AFR, 2/15/2008? the new version / .iso is ?2rj964a.iso?. However, there is no executable and even though I was able to stumble my way through the French BIOS set up and change the boot sequence to CD/DVD first, it will not boot on start up. The flash from within Windows BIOS version on the Lenovo site is an executable, but only supports a 32 bit OS. Is there a separate flash utility that I can use that will allow me to drive the new BIOS flash from inside Windows 7 64 bit? Basic steps would be good, I could never be accused of being a technical all-star. Thanks

A:BIOS Flash Question Lenovo ThinkCentre M57 6072-AUF

Hi Welcome to Seven Forums .. There is no executable for the 64 Bit OS .. Try tapping F1 or F2 at start up .. That should give you bootable Options ..

Read other 7 answers
RELEVANCY SCORE 86.4

Hello,today we updated new BIOS 9SKT94AUS to ThinkCentre M92p, previous state with Win7, we needed do upgrade to Win10.Now after BIOS update is device not booting, only thing we can do is access BIOS setting or choose boot device thru F12 or F1.We did:F9 (reset to default), CMOS reset (1-2/2-3 pin) - no change, UEFI/LEGACY - no changeLINUX (no change), Installation media (USB/DVD of W7, W8, W10, network boot) - no changeAfter choosing boot device directly we get when USB e.g. flash is inserted Lenovo logo hanging,when CD/DVD inserted underscore hanging.Anyone any ideas?Thanks,Tomas

Read other answers
RELEVANCY SCORE 86.4

Recently my lenovo laptop  z50-70 start blocking on black screen before lenovo logo appears on start up with led light on. It lastes from 15 minutes to even 2 hours before lenovo lego appears and laptop starts and works smoothly with no problems.Now it is blocked on black screen and can t proceed to lenovo logo. I can t acces bios menu.I tried bios reset. no effect.I updated the bios to the last version. no effect.

Read other answers
RELEVANCY SCORE 86

Hi Over the last few weeks i have been attempting unsuccessfully to fix my laptop, i have tried every fix i have come across and nothing seems to help. My problem is that my laptop constantly returns to the lenovo splash screen.  I have replaced the hardrive to an ssd as i presumed this may be the problem it detects the hardrive so i believe it is working as intended.  When i try to do anything fresh install of windows, change bios settings etc the laptop closes these windows and returns to the lenovo screen. One issue i can maybe see is that in BIOS information it detects two hardrives the samsung ssd i have installed and a liteonit lss-16l6g . What is the liteonit hardrive? i cant seem to remove it. Has anyone had the issue where it constantly returns to the lenovo screen even when trying to install windows.  Thanks

A:Lenovo u530 bios help, constantly returns to lenovo screen

I have just found the lss ssd and removed it, not sure what its purpose was.

Read other 1 answers
RELEVANCY SCORE 84.8

Might someone be able to please assist?   Ran the BIOS update to version 9SKT75A through the ThinkVantage System Update and the computer now fails to bring up a BIOS screen or load windows.  Looks like the BIOS update failed even though did not interrupt power supply or boot cycle, per instructions. Looking for the original POST and BIOS update file for M92p Tiny to run the boot block recoery as per Lenovo help article here:  http://support.lenovo.com/en_US/detail.page?DocID=HT077504.  However, the link within the article to download the file for  'ThinkCentre M92/p, M92p Tiny, M82, Edge 92, E31' is broken.  See here:  http://download.lenovo.com/ibmdl/pub/pc/pccbbs/thinkcentre_bios/9sj942usa.iso  Does any one have the originial BIOS update file for the boot block procedure for this computer that would be willing to share? To Lenovo: can you please fix the following link on your help site and make the original POST and BIOS update file available again?   Thank you, M

A:ThinkCentre M92p Tiny - Failed BIOS update though Lenovo ThinkVantage - please help

Problem solved toay,You need to open your machine. Find the cmos clear jumpers.Move the little cup from positions 1-2 to 2-3. Unplug Hard Disk. Close the machine. Insert a portable USB DVD to a usb port (have a copy of the new bios on the cd) and turn on your machine. It will boot from USB DVD drive and it will load the new bios. Machine will shut down after the new bios update. Open agin the machine, plug the Hard Disk and put back the jumpers to 1-2 position. Unplug USB DVD and it will boot from Hard Disk. That's all. IN OTHER WORDS: Bios update can be done if first you change the jumpers on motherboard.

Read other 1 answers
RELEVANCY SCORE 84.4

Need some help here. Beyond frustrated.
 
Windows 7
Mobo Gigabyte GA-277-D3H
Vid Card EVGA GTX 560 (trying to replace with GT 730 "low profile", which I'm also pissed off with because it's about half the size of the 560, so I know it's going to suck. Was in a rush to fix this crap and didn't research much)
PSU Silencer Mk2 750wats
 
Started when my computer crashed with a video anomaly. It's not something very new, as I've been having crashing and video anomaly problems with this card for years and I figured it was only a matter of time before it gave up the ghost.
 
Tried restarting my comp a few times and it continued to make all of the bootup noises, including letting me log in with my password (even though the screen was blank). After trying this a few times, it stopped getting that far and would only have the one initial start up beep.
 
Got this new video card, which I was immediately displeased with as stated earlier. Hooked it up, which restored video and that's when I found that the computer would not boot past the BIOS splash screen. Gives the single beep, fans spin up like usual, then nothing. BIOS related buttons a few times with no response, it starts a "clicking" noise whenever pressing them. Still doesn't progress past this screen.
 
Tried taking out the ram, that causes an error where the comp just makes continuous beeping noises (read that it giving an error is an indicator that the mobo is still good). Don't get any further disconnec... Read more

A:Computer stuck at BIOS splash screen

Start with these free, bootable hardware diagnostics:  http://www.carrona.org/hwdiag.html
I suspect memory because of the beeps, but I suspect the hard drive because of the freezing at the BIOS splash screen (so try both diagnostics).

Good luck!

Read other 11 answers
RELEVANCY SCORE 84.4

Hi everybody :

This is a question about Windows 7 Operating System. I notice, every once in a while, when I boot up, the display gets stuck on the BIOS splash screen. Then I manually turn my computer off.....wait a minute before booting back up. Then the BIOS screen only displays for a second or so, then proceeds with the boot up process. Is this indicate that my Operating System might've gotten corrupt ? My Operating System is : Windows 7 Professional / 32-bit.
Thanks,
garystan

A:Display gets stuck on the BIOS splash screen

Hi try running these, No. 1 SFC /SCANNOW Command - System File Checker - Windows 7 Help Forums
No. 2 The How-To Geek Guide to Using Check Disk in Windows 7, 8, or 10

Read other 1 answers
RELEVANCY SCORE 84.4

Arighty,

So yesterday I got a GeForce GTX 960 4GB to install into my PC. However after installing it and all that jazz, my computer gets stuck on the BIOS splash screen and beeps. The beeps are one short beep, then 30 seconds later a short beep followed by 3 shorter beeps.

I know for a fact that it isn't my RAM because I can put my old card in and everything works fine. I also have a VisionTek 450w dedicated GPU power supply that takes up a CD reader slot so power consumption is totally fine.

I tried updating my bios, but there doesn't seem to be an update available. So at this point I think I need a new motherboard.

My specs are as follows;

Motherboard: Pegatron IPISB-CH2

BIOS: AMI 7.12

CPU: Intel Core i5-2320 (Sandybridge) (95W), 3.0 GHz

RAM: 8GB DDR3

HDD: 1 TB WD Harddrive that I bought 2 months ago

GPU before: GTX 650 Ti 1 Gb

After: GTX 960 4GB

Thanks for all the help!
 

A:PC stuck on BIOS Splash Screen after installing new GPU

I can put my old card in and everything works fine.Click to expand...


So at this point I think I need a new motherboard.Click to expand...

This makes no sense at all. If you reinstall your old card and everything works, why in the world would you think you need a new mb???
That scenario points at a failed or DOA card NOT a failed mb.

If you are intent on gaming, I would give serious consideration to building a gaming system. Big box systems like dell, hp, etc are fine for what they are intended to do; email, run office, watch videos, etc. The hardware is just not up to the stress of gaming. There is more to a gaming system than simply installing a video card and a pw supply.
 

Read other 3 answers
RELEVANCY SCORE 84.4

i had issues with my screen it had like splash like the photo.. but less .. only had few lines.. it happen everything when i turn on my laptop for 1 minute after that screen still working fine.. if i turn off and turn on after few a hours it started with the same issues.. i found in lenovo.com this: Causes of display failures:Monitor is not on                                              -? for real i saw the line and my monitor isnt on jajaComputer is asleep                                          -????? i never put my laptop in this mode.... just on or off.Connections not properly connected          -it was working fine just few days ago i started had this issues. also i                                                                                        checked the port and is fineMonitor settings are not correct                    -mmmm I put all my laptop default setting.. and nothingNo POST (power-on-self-test)             &nbs... Read more

Read other answers
RELEVANCY SCORE 84.4

i had issues with my screen it had like splash like the photo.. but less .. only had few lines.. it happen everything when i turn on my laptop for 1 minute after that screen still working fine.. if i turn off and turn on after few a hours it started with the same issues.. i found in lenovo.com this: Causes of display failures:Monitor is not on                                              -? for real i saw the line and my monitor isnt on jajaComputer is asleep                                          -????? i never put my laptop in this mode.... just on or off.Connections not properly connected          -it was working fine just few days ago i started had this issues. also i                                                                                        checked the port and is fineMonitor settings are not correct                    -mmmm I put all my laptop default setting.. and nothingNo POST (power-on-self-test)             &nbs... Read more

A:lenovo y70-70 splash on the screen

Hi Alex88sx22cm,
 
Welcome to the Community Forums.
 
You may check how the display is on another monitor.
Turn off the machine and power on using the novo button (page 62) to access the BIOS set up screen and compare the screen.
 

 
If you have the same distorted display in the BIOS screen but show fine on an external monitor then probably LCD /cable may be the issue and would be best attended with your local service center.
 
Update us how it goes.
 
Regards
 

Read other 1 answers