Over 1 million tech questions and answers.

BSOD every few hours: mostly "STOP: 0x00000F4", "c00021a" & "c0000135"

Q: BSOD every few hours: mostly "STOP: 0x00000F4", "c00021a" & "c0000135"

Hi everyone!

Yesterday my HP laptop (Windows 7) started getting BSOD with various types of errors (mostly "STOP: 0x00000F4", "STOP: 0x0000007A", "c00021a" and one "missing %hs, c0000135"). Most of the time it restarts without any issues and works fine right after the BSOD and then an hour or two later I get a BSOD again.

I have tried restoring to Last Known Good Configuration, startup repair, hard disk check, virus scans and I also uninstalled any recently added programs I could think of and cleared up more than 50% of my hard disk space. None of these seem to have helped and I still get BSOD regularly.

I have attached the folder from the SF Diagnostic Tool and would appreciate any advice!
Thank you!

RELEVANCY SCORE 200
Preferred Solution: BSOD every few hours: mostly "STOP: 0x00000F4", "c00021a" & "c0000135"

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: BSOD every few hours: mostly "STOP: 0x00000F4", "c00021a" & "c0000135"

Welcome to the forum.

MSINFO32:
Please go to Start and type in "msinfo32.exe" (without the quotes) and press Enter
Save the report as an .nfo file, then zip up the .nfo file and upload/attach the .zip file with your next post.
Also, save a copy as a .txt file and include it also (it's much more difficult to read, but we have greater success in getting the info from it).
------------------------
Upload a screenshot using: CrystalDiskInfo For how to upload a screenshot or file, read here
Test your Hard Drive(s) by running: Hard Drive Diagnostic Procedure
------------------------
Test and Diagnose RAM Issues with Memtest86+: RAM - Test with Memtest86+


Tip
Pay close attention to Part 3 of the tutorial "If you have errors"
Test the RAM with Memtest86+ for at least 7-10 passes. It may take up to 22 passes to find problems. Make sure to run it once after the system has been on for a few hours and is warm, and then also run it again when the system has been off for a few hours and is cold.


------------------------
Monitor hardware temperature with system monitoring software like Speccy or HWMonitor. Upload a screen shot of the Summary tab as well:Piriform - Speccy
CPUID - HWMonitor
For how to upload a screenshot or file, read here

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck F4, {3, 87a2e968, 87a2ead4, 83a55cf0}

----- ETW minidump data unavailable-----
Probably caused by : csrss.exe

Followup: MachineOwner
---------
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

Use !analyze -v to get detailed debugging information.

BugCheck F4, {3, 87a7bd40, 87a7beac, 83a1fcf0}

----- ETW minidump data unavailable-----
Probably caused by : csrss.exe

Followup: MachineOwner
---------

Read other 5 answers
RELEVANCY SCORE 252.4

In Windows XP, fully updated, I have several folders full of mp3's and want to see the bit rate and duration. I right click on a column heading and select "Bit rate". I then click on "More..." so I can get to "Duration", and I select that one too.

But all the figures in the "Duration" column appear to be in "hours" and "minutes", so I see "00:04" or "00:03", but what I want is "minutes" and "seconds".

Any thoughts as to how to change this?
 

A:Solved: Windows Explorer "Duration" Column - no "Seconds", just "Hours" and "Minutes"

Read other 16 answers
RELEVANCY SCORE 249.2

I am running Windows XP SP3, fully updated, on an Acer lap top PC.

I have several folders full of .mp3's and want to see the bit rate and duration. To do this I right click on a column heading and select "Bit rate". I then click on "More..." so I can get to "Duration", and I select that one too.

The two new columns appear, but the format of the "Duration" column appears to be "hours:minutes", so I see "00:04" or "00:03" for most .mp3's, when what I want to see is 'hours:minutes:seconds", e.g. "00:03:45".

This also happens for video files (.avi files), e.g. all my episodes of "Heroes" (sad, I know) have a duration of "00:42" instead of "00:42:xx".


Here are two pictures showing the problem with the .mp3's. The first is of Explorer showing the Duration as "Hours:Minutes":




The second picture is of the properties window of the first .mp3 in the list above:




I copied some .mp3 files to another (old) PC on my home network, and it displayed the duration field correctly:




Also, the properties window correctly shows the duration also:





I'm not the only person to have this problem. I received a private message from a member of another forum where I posted about this problem several weeks ago. That person also has the same problem with the duration field.

The tech guys on that forum were unable to find the source... Read more

A:Windows Explorer "Duration" Column - no "Seconds", just "Hours" and "Minutes"

* bump *

Tricky, this one!

Read other 8 answers
RELEVANCY SCORE 248

Hey everyone,
        I am trying to get the REST queries to work with the sharepoint end points instead of graph end points. I first created an app with relevant permissions and have given it the admin consent. Then I am hitting the https://login.microsoftonline.com/<tenant>.onmicrosoft.com/oauth2/token?Content-Type=application/x-www-form-urlencoded end
point with https://<tenant>.sharepoint.com as resource. I am then using the access token retrieved to give the rest call to https://<tenant>.sharepoint.com/_api/v2.0/drives/b!3indYSbqZ0-hVSPnCgIZy-2xDMh7jH9AuQnEzJMc6TEfQoSJvJT-R6tT0lFBQiPr/root/delta
but it is failing with "error":{"code":"generalException","message":"General exception while processing"}}. The REST response code is 401 Unauthorized. I have filed a Microsoft support ticket but they
have asked me to post on these forms. Can someone please help me with this? I am not able to move forward because the error is pretty generic and doesn't give any additional details.
Thanks,
Sai Kiran Katuri.

Read other answers
RELEVANCY SCORE 227.6

I got my dell few days ago. Installed it with Samsung EVO 850 SSD 500 Gb and Kingston 8GB PC3L - 12800 SODIMM.The Windows 10 Home OEM home is installed on HDD 1TB so I decided to use Samsung Data Migration software to clone the data to SSD. However, the OS crashed and decided to install a fresh Windows 10 Enterprise to SSD and deleted the previous OS on HDD using diskpart.Now after Installing Windows 10 Ent OS files. Every after BIOS run, I got BSOD errors "MEMORY MANAGEMENT" + "Page Fault it non paged area" + "IRQL NOT LESS OR EQUAL" 

Read other answers
RELEVANCY SCORE 219.6

Hello guys, the last week I've been strugling with these nasty BSODs. At first I thought it was my HDDs as ntoskrn.exe somewhat hinted towards that from googling it. My HDDs have been causing a lot of trouble earlier as well due to their somewhat long years of service. However, I've recently reformated my computer and installed W7 on a brand new Corsair Force GT 120GB SSD hoping the BSODs would go away, they didn't.

I googled BSOD and I stumbled upon this forum and I thought I'd give it a try. I'm somewhat desperate, as I need my computer working for both work, school and amusement.

I've been trying to run Memtest in order to test my memory but without any results. I'm also currently running on only on 4GB chip instead of two, to see if the problem still exists. Also, without any results.

This is the second time I'm writing this thread btw, I was just about to post it and my PC crashed.

Here is my two logs + dxdiag (last crash didn't generate a log oddly enough).

Here is additional hardware/gear that I use:

Razer Megalodon 7.1 Headset
Razer Naga
Logitech G19
Logitech C920 (Webcam)
Corsair 750W PSU

My temperatures are also good. Both CPU and MB idles at around ~25. GPU's all good too. I'm also using a Corsair 650D chassi with dustfilters at both air-income so dust is minimal. On top off this, I use airpressure to clean away dust somewhat regularly and I also did exactly this 2 days ago when I reinstalled the pc.
... Read more

A:BSOD - "Memory management", "Bad pool header", "ntoskrnl.exe"

Are you over-clocking? Is the bios set to its defaults? Is the SSD set on a SATA 3 port in AHCI mode?
 

Read other 5 answers
RELEVANCY SCORE 217.2

My office just upgraded, and I can no longer use Windows XP. On this system, I was able to add a separate taskbar to facilitate quick access to commonly-browsed folder locations on our vast network, and another one expedited the launching of useful programs and lists. Each task on each taskbar was represented with a big custom icon to save eye strain. I had them installed in opposite vertical margins, and they were set on auto-hide to keep them out of the way when not being used. Just move your mouse pointer to the left or right margin, and BAM! Sorry for the cliche, but I really got used to the convenience of what I had set up, and I just don't think I can be as efficient without anything comparable.

Now there appears to be nothing comparable in the Windows 7 GUI, and it's making me sick with rage! I see only the option to put a "toolbar" on an existing "taskbar", and no option to create any additional taskbars! This cramps up your one-and-only taskbar, plus the tiny toolbar access buttons require way too much precision for anything that's supposed to be quick. When you've figured out how to bring up that ridiculous button, the list that it yields is small enough to cause painful eyestrain - nothing efficient, much less cool about this at all! I have seen customization options in other OS GUIs that may have resolved some of these issues, but I see none such in W7.

I have tried every google search string that I can think of, and found... Read more

A:Need to add "TASKBARS" (MSese for "Launchpads", "Docks" NOT "Toolbars"

Several possibilities here: Second taskbar in windows7? [Solved] - Windows 7 - Windows 7

Read other 1 answers
RELEVANCY SCORE 216.4

Hi,

When our website users click on an html attachment embedded on a web-page in IE9, the download manager will not display the "Open" option. It will only display "Save" and "Cancel" which our users don't like, having to save the
html document in a folder to open it. Whereas, when downloading attachments like pdf, word etc. all three options are displayed. 

Is there any setting to tweak , which will display all the 3 options for HTML attachments as well?

A:IE9 download manager will not display "Open" option (only "Save" and "Cancel" is displayed) for downloading HTML documents.

Hi,
As you know, the Open-Save-Cancel dialog box helps you prevent your computer from affecting by virus while downloading. 
So I suggest you test to reset all zones to a lower level temporarily and then please attempt to download this html attachment again.

However, since you can normally download the other documents, I suspect there is some restriction in the website which you are trying to view. I recommend you to contact the administrator of that website if possible.
could you please send me the link of the website from where you are trying to download the html attachment?
Thanks!


We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Read other 6 answers
RELEVANCY SCORE 215.6

I am infected with this crap and have used the following tools to try to get rid of it:
Windows Defender, Unible PowerSuite (SpeedUpMyPC, Registry Booster & Spyware Protector) and Norton's One Button Checkup and WinDoctor.

Not sure if it's related, but my DISPLAY is locked at 640 X 480.

Atempted the 5 Step Process before posting and Panda ActiveScan froze and crashed after scanning 59253 files, but not before identifying 28 spyware files.

Here's my extra.txt log from Deckard's:

Deckard's System Scanner v20071014.68
Extra logfile - please post this as an attachment with your post.
--------------------------------------------------------------------------------

-- System Information ----------------------------------------------------------

Microsoft Windows XP Home Edition (build 2600) SP 2.0
Architecture: X86; Language: English

CPU 0: Intel(R) Pentium(R) 4 CPU 2.80GHz
Percentage of Memory in Use: 36%
Physical Memory (total/avail): 1277.95 MiB / 810.39 MiB
Pagefile Memory (total/avail): 1516.89 MiB / 1165.44 MiB
Virtual Memory (total/avail): 2047.88 MiB / 1930.88 MiB

A: is Removable (No Media)
C: is Fixed (NTFS) - 37.21 GiB total, 18.7 GiB free.
D: is CDROM (CDFS)

\\.\PHYSICALDRIVE0 - ST340014A - 37.25 GiB - 1 partition
\PARTITION0 - Unknown - 39.19 MiB
\PARTITION1 (bootable) - Installable File System - 37.21 GiB - C:



-- Security Center -------------------------------------------------------------

AUOptions is scheduled... Read more

A:Netsky Worm-Popups-The Three Icons - "Error Cleaner" "Privacy Protector" "Spyware..."

Bump.

Read other 14 answers
RELEVANCY SCORE 215.6

I am trying to use the fsutil file setshortname to set "Program Files" to PROGRA~1,

but the system is giving me an "Error: Access is denied" response.
what I have typed:
Microsoft Windows [Version 6.3.9600]
(c) 2013 Microsoft Corporation. All rights reserved.
C:\Windows\system32>cd /d D:\
D:\>fsutil.exe 8dot3name set 0
The registry state is now: 0 (Enable 8dot3 name creation on all volumes).
D:\>fsutil file setshortname "Program Files" PROGRA~1
Error:  Access is denied.
And I try it in Safe Mode.It is also "Access is denied.".
Can someone
help me?

A:"fsutil file setshortname "Program Files" PROGRA~1"=>"Error:Access is denied."

Hi TimFF,
This might be related with the UAC settings, check this thread:
give full permission for the users in program
files folder
The steps in the above thread is not recommended.
For the short name usage, we may consider to create a directory-junction from
PROGRA~1 to C:\Program Files:
With the following commands:
mklink /J "C:\PROGRA~1" "C:\Program Files"
Reference:
Mklink
Best regards


Michael Shao
TechNet Community Support

Read other 3 answers
RELEVANCY SCORE 215.2

Hi all.
I am getting a blue screen error of: stop: c0000135" and "winsrv was not found". It is not due to installing SP2 or any type of service pack. It happened after I used RegCure, i believe that it corrupted my registry and now it cannot find the winsrv. I was wondering how i would go on about fixing it. At the moment I am using a Linux Live CD and I have access to all my files on my hard drives including the windows partition, so if there is a way to revert to old registry settings through that please let me know.
FYI: I am using XP x64.
Thank you.

A:stop c0000135" and "winsrv was not found" error

bump*

Read other 2 answers
RELEVANCY SCORE 214

I double-click and get "search" instead of "open"--only when I click a disk, like Hard Drive C: or Floppy A: or CD F: and so on.

It didn't used to do this, so I must've inadvertently changed some setting somewhere, but darned if I can find it now.

Any ideas?
 

A:Solved: On the "my computer" list, I double-click on disks and get "search" instead of "open"

Read other 12 answers
RELEVANCY SCORE 214

It seems that no matter how I set this, after the next start-up it reverts to "15 minutes".  What registry key controls this?

Read other answers
RELEVANCY SCORE 214

Ok, so im new here so hey everybody..

to the point: my laptop is "stuttering"/lagging/skipping.
whatever you wanna call it its doing it.
my video/music/and cursor skip every second for a splt second it starts on start-up and dont stop til i turn my laptop off. it happens in a pattern its not random, ive done checked my drivers, spyware, and m RAM is good.. so can someone please help me? ***could it be because my battery wont hold a charger? so it has to be hooked up to the charger at ALL times or it dies Example: is the charger not got the "juice" to run the laptop by itself so it studders/skips..*** i dont know if this has anything to do with my problem but i ran "event viewer" and found this : The following boot-start or system-start driver(s) failed to load:
Cdrom
Imapi
redbook

PLEASE HELP




OS Version: Microsoft Windows XP Home Edition, Service Pack 3, 32 bit
Processor: Genuine Intel(R) CPU T2250 @ 1.73GHz, x86 Family 6 Model 14 Stepping 8
Processor Count: 2
RAM: 502 Mb
Graphics Card: Mobile Intel(R) 945GM Express Chipset Family, 224 Mb
Hard Drives: C: Total - 39723 MB, Free - 23484 MB; D: Total - 12684 MB, Free - 3633 MB;
Motherboard: Dell Inc., 0FF049, , .HWPLLB1.CN1296167S5169.
Antivirus: McAfee VirusScan, Updated: Yes, On-Demand Scanner: Disable
 

A:Solved: Whole computer "studders"/"skips"/"lags" .. have event viewer report (PLEASE

Read other 6 answers
RELEVANCY SCORE 212

Basic system description:
Desktop PC about 2 years old with:
Motherboard: Asus P5Q-E
Processor: Intel Core 2 Quad Q6700 @ 2.66GHz
RAM amount: 8GB
Operating System: Windows 7 Professional Service Pack 1 OEM 64 bit
Graphics Cards (I have two installed and software controllable CrossFire): AMD Radeon HD4850 driving 4 monitors. Driver version 8.961.0.0
Hard drive: 1 TB Western Digital WDC WD1001FALS-00J7B1

Crash situation and background:
The system tends to crash with no application running or all applications running. By "applications" I mean -other than standard chart and browsers:
1. Battlefield 3 Limited Edition.
2. Sierra Chart: Sierra Chart - Futures, Stocks, Forex Charting and Trading Software Platform
3. InteractiveBrokers.com
4. Picasa
5. Adoble Lightroom 4

Last week, I installed the latest drivers for most and including the video card drivers after a whole series of BSoD and also UNINSTALLED Battlefield 3 ... I thought I fixed the problem and this computer feels slightly faster, etc. Today, while I was away and while the computer is running item 2 and 3, the computer gave me a BSoD as per attached screen shot.

HELP!!!!!!!!!!!!!!!!

A:BSoD with "STOP:0x00000024" error and "Ntfs.sys"

Hello rting,
You have quite a few different types of crashes there.
Before we investigate the underlying causes it would be wise to do the following.

1. Asacpi.sys

The pre 2009 version of this driver is a known BSOD cause.





Quote:
Please visit this link: Asus tek computer inc. -support- drivers and download p7p55d le

ASUSTeK Computer Inc. -Support- Drivers and Download P7P55D LE
ASUSTeK Computer Inc. - Motherboards- ASUS P5K-VM

Scroll down to the utilities category, then scroll down to the "atk0110 driver for windowsxp/vista/windows 7 32&64-bit" (it's about the 12th item down).

Download and install it.

Go to c:\windows\system32\drivers to check and make sure that the asacpi.sys file is date stamped from 2009 or 2010 (not before).


2. McAfee is a frequent cause of BSOD's.
I would remove and replace it with Microsoft Security Essentials AT LEAST TO TEST!

http://download.mcafee.com/products/...tches/MCPR.exe

Microsoft Security Essentials - Free Antivirus for Windows

Read other 9 answers
RELEVANCY SCORE 212

Ok, so im new here so hey everybody..

to the point: my laptop is "stuttering"/lagging/skipping.
whatever you wanna call it its doing it.
my video/music/and cursor skip every second for a splt second it starts on start-up and dont stop til i turn my laptop off. it happens in a pattern its not random, ive done checked my drivers, spyware, and m RAM is good.. so can someone please help me? ***could it be because my battery wont hold a charger? so it has to be hooked up to the charger at ALL times or it dies Example: is the charger not got the "juice" to run the laptop by itself so it studders/skips..*** i dont know if this has anything to do with my problem but i ran "event viewer" and found this : The following boot-start or system-start driver(s) failed to load:
Cdrom
Imapi
redbook

PLEASE HELP
 

A:Whole computer "studders"/"skips"/"lags" .. have event viewer report (PLEASE HELP)

**(DONT KNOW IF THIS WILL HELP..)***

Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows XP Home Edition, Service Pack 3, 32 bit
Processor: Genuine Intel(R) CPU T2250 @ 1.73GHz, x86 Family 6 Model 14 Stepping 8
Processor Count: 2
RAM: 502 Mb
Graphics Card: Mobile Intel(R) 945GM Express Chipset Family, 224 Mb
Hard Drives: C: Total - 39723 MB, Free - 23484 MB; D: Total - 12684 MB, Free - 3633 MB;
 

Read other 2 answers
RELEVANCY SCORE 211.2

ok!!!!!!!!!! what is it and how do i fix it,,,, eyes crossed knees woobly help?????????????????????
 

A:[Solved] mplay32.exe,1"/play/close"%L"." and sndrec32.exe"%L"."

Read other 9 answers
RELEVANCY SCORE 210.8

Hey All i got a pretty serious problem i just got done reformating tonight and i goto get service pack 2 and i install it it says restart when its doen so i do and i get You receive a "Stop: c0000135" and "winsrv was not found" error message everytime i try to boot up ive tried last known good config and safe mode all of them come up with the same message the only thing i havent tried is chkdsk but i dont think that will do anything if anyone knows anything some help would be great i just got all my stuff installed too so this really sucks

A:Stop: c0000135" and "winsrv was not found"

http://www.maximumpc.com/2005/01/how_to_slipstre.html

Read other 2 answers
RELEVANCY SCORE 208.8

Ok so I'm using a custom visual style made by another user however I don't really like the buttons used that I mentioned above. The creator states it is acceptable to change the theme to however you like as long as you don't redistribute it anywhere.

Ok so I opened up the .msstyles file (using Restorator) located in the theme folder of this VS. I went into the images directory and located what seems to be the images used for the buttons. Intuitively, it seems like it would make sense to replace those images with different ones (perhaps from another visual style) and it should change them. However, would this actually work? Could the theme get messed up in some other way (like proportions or something if the new button images are smaller)? I don't know of any other way to change them that would be easy.

But I did run into another problem. For some visual styles I can't even locate those buttons in the images directory. Where else would they be?

A:Changing the "minimize" "maximize" and "close" buttons of a theme

Use Windows Style Builder to do that...

Read other 9 answers
RELEVANCY SCORE 208.8

I am using Windows 7 on my laptop and I have question about when to use "Home", "Work" and "Public" profile.

If I am logging in without setting password, and I am logging in network with "Public" profile, then will any other user, who can see my computer, be able to enter my computer and check the contents on my computer ?

I am connecting to a network and there are 6 other users connected to this network. In the set network location window, if I select the netwoek as "Home", does it mean that other 6 users will not be able to see my computer on network and if I use "Public", then all other six users will be able to see my computer on network ?

Thanks

Read other answers
RELEVANCY SCORE 208.8

Hi all,

So I'm kind of stuck.. I currently have the problem where I am in an endless cycle of "loading files" -> "Windows Boot Manager" (see: How To Boot Into Safe Mode On Windows 8 (The Easy Way)).
I have tried to load all of the options -- and none successfully load.
I also end up at a OneKey Recovery as well.. unfortunately, the laptop does not have initial backup or user backup images.
I have a Windows 8 CD for repairing purposes.. however, I cannot load the BIOS/UEFI to change the boot order to load the optical drives first. I have also tried to remove the CMOS battery to fix it.. did not work. .
Also - Windows Boot Manager:
Windows Setup [EMS Enabled] -- does not load properly (leads to OneKey Recovery) Safe Mode (does not load properly) Safe Mode with Networking (does not load properly) Safe Mode with Command Prompt (doesn't load - tries to boot and load all files onto partition that is too small.. can't change partition?)
Enable Boot Logging Enable Low-Resolution Video Debugging MOde Disable automatic restart on system failure Disable Driver Signature Enforcement Display Early Launch Anti-Malware Driver
Start Windows Normally
Any ideas would be greatly appreciated! Thanks!

Read other answers
RELEVANCY SCORE 208.8

Example sentence: vrytim I prss ths kys, nothing happns. Now I'm writing with my on-sreen keyboard. I'm clueless when it comes to computer stuff. How do I fix this? Is this a software problem, or a hardware problem?Help is much appreciated!

A:Kyboard deos not respond to the keys: "e", "d", "c" and "3"

My keyboard hath the thame problem with the thupid eth key. The blathted thing ith driving me nutth.

All theriousneth...er...seriousness aside, usually, that is a hardware problem. Can you find or borrow another keyboard and see if it will work correctly on your machine?

Read other 6 answers
RELEVANCY SCORE 204.4

MS thinks that one of my PCs is running W7 that's not genuine. It is genuine - at least I bought it from Amazon and paid ?141 for it so that - to me - means it's genuine. It may not be but neither Amazon nor MS will take any responsibility for it not being genuine so I've given up with them both. I think that the issue arises because of hardware changes I've made. Oh - yes, I've lost the box with the key on it too.

Long story short. I use this PC very little and when I first first got the black screen and messages after I installed a larger hard drive and reinstated the drive image from an Acronis backup. I stupidly forgot to reinstate the drive signature. Then it happened again when I changed the ITX motherboard.

Now here's the real question. Every now and then it gives me the "black screen" treatment. I fix it by restoring a drive image and turning off W7 updates.
If the damned thing is told not to call home then it shouldn't should it? What's going on? It seems to give me a month or two and then goes psycho on me like HAL9000!

A:How do I stop W7 "calling home" and displaying "not genuine" messages?

If this is an OEM version then I can understand why it's doing this after you changed motherboards, since it is forever tied to the first one it is installed on.

If you can follow these instructions for activation issues,

Windows Genuine and Activation Issue Posting Instructions

The results of that can help resolve your issue.

Filling in your system specs will help as well,

System Info - See Your System Specs

If your installation is valid then there's no reason to turn off updates or try to keep it from calling home.

Read other 6 answers
RELEVANCY SCORE 204

hi,

OK, this is a weird one.

I wanted to move the "My Music", "My Pictures", "My Videos" folders to another HDD. I moved the "My Documents" Folder to this HDD without a problem but the others I accidentally set the whole HDD as the folder (if that makes sense). So now the music, videos and pictures folders are set to this HDD and dont have an actual folder to change the properties of. Therein lies my dilema.

If anyone can offer any advice on this curly issue it would be greatly appreciated.

Shane

A:Remaking "My Music", "My Pictures", "My Videos" folders

  
Quote: Originally Posted by Legume


hi,

OK, this is a weird one.

I wanted to move the "My Music", "My Pictures", "My Videos" folders to another HDD. I moved the "My Documents" Folder to this HDD without a problem but the others I accidentally set the whole HDD as the folder (if that makes sense). So now the music, videos and pictures folders are set to this HDD and dont have an actual folder to change the properties of. Therein lies my dilema.

If anyone can offer any advice on this curly issue it would be greatly appreciated.

Shane


You have a backup from before the problem started? a win 7 dvd to do a repair install?
ken

Read other 4 answers
RELEVANCY SCORE 204

I tried to associate the file extension .txt to a new editor program
with the well known cmdline programs ASSOC and FTYPE.

No, assigning them through WinExplorer menu does not work.
But this is another problem which should not discussed here.

When I type now one of the following alternative commands at the CommandPrompt then Win7 returns me something like:

assoc .txt=txtfile

"Access denied"
The following error occurs: .txt"

or

ftype txtfile=D:\notepad++\notepad++.exe "%%1"

"Access denied"
The following error occurs: txtfile"

Why?

The command above work fine under WinXP

Peter

A:"access denied" when using "assoc" and "ftype" from cmdline?

Question:

Did you run cmd.exe with administrative previlliges?
Elevated Command Prompt

Read other 3 answers
RELEVANCY SCORE 204

Hi guys, I ask you a lot of help because I'm in trouble up to my neck. I try to be as detailed as possible.
I have a Packard Bell with initially installed Windows Vista Home Premium (I don't know if 32-bit or 64-bit). Over time I updated it to later versions, and in fact before the problem I normally had Windows 10.

Brief introduction: as you know, telematic lessons have started in the world at home. So I installed Microsoft Teams and so far everything is ok. I noticed, however, immediately that the fan of my old PC with more than 10 years of intense work was starting to fuel quickly. While I was thinking about how to solve, the inevitable happened: during a lesson the PC freeze in the screens, and after waiting 5-10 minutes I turned it off by the button. By re-accessing it, this screen appeared, as the title says:

"Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
1. Insert your Windows installation disc and restart your computer.
2. Choose your language settings, and then click "Next."
3. Click "Repair your computer."

If you do not have the disc, contact your system administrator or computer manufacturer for assistance.

File: \ Boot \ BCD
Status: 0xc000000f
Info: The Boot Configuration Data for your PC is missing or contains errors. "

What I did: I searched on this and other sites but I was not able to juggle well. I understood that you need an installation CD, which I DO NOT ha... Read more

Read other answers
RELEVANCY SCORE 204

Ok, so basically, whenever I turn the computer on, 3 error messages appear:

- A virtual driver failed to inicialize DLL. Chose close to end the program. H:/Windows/system32/code/pRee.exe

- A virtual driver failed to inicialize DLL. Chose close to end the program. H:/Windows/system32/code/pRee1.exe

- Error loading H:/Archiv~/GBPLUG~/gbiehcef.dll. Couldn't find specific module.

(sorry if some terms are incorrect, my computer is in Spanish, to I tried to translate as best as possible)

Please help me solve this terrible problem, it is really getting me on my nerves! (oh, and if this helps, I've recently donwloaded this so called "Limewire acceleration", and whenever I ran the setup, it didn't work. I don't really remember the name of the website I downloaded it from, sorry...)

A:Can't Open "My Documents", "Trash" or other files in "My Computer"!?

Hi and Welcome to the forum

I am almost certain that you have malware problems. Most like caused by you doing file sharing/ P2P - Limewire.

Suggest that you go here and follow the directions:

http://www.techsupportforum.com/secu...oval-help.html

Please be advised that the malware people are very busy and it could take a couple days to assist you.

BG

Read other 1 answers
RELEVANCY SCORE 204

I thought I was computer savvy until this problem came up. When I double click my computer, recycle bin, control panel, etc, the hourglass comes up for a few seconds, goes off, and nothing else. No error messages or anything, just nothing. I have viewed a few of the threads covering this and a common link was the hijack this result. I have posted that here, and really hope that someone can help me with this. I have run SpyBotSD and adaware, I have run mutiple virus scans, I did an SFC, and the final thing was to repair windows using the original disk, none of which has help. I am running Window XP w/SP2. Any other suggestions would be certainly appreciated. Hope to here from someone soon. MTCS, out.

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\spoolsv.exe
C:\Program Files\Common Files\Symantec Shared\ccSetMgr.exe
C:\Program Files\Symantec AntiVirus\DefWatch.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\PROGRA~1\TDSTEL~1\ENTERN~1\app\pppoeservice.exe
C:\WINDOWS\system32\svchost.exe
C:\Program Files\Symantec AntiVirus\Rtvscan.exe
C:\Program Files\Common Files\Symantec Shared\ccEvtMgr.exe
C:\WINDOWS\Explorer.EXE
C:\WINDOWS\system32\wuauclt.exe
C:\Program Files\Hewlett-Packard\Toolbox2.0\Apache Tomcat 4.0\webapps\Toolbox\StatusClient\StatusCl... Read more

A:I cannot open "my computer" "control panel" "recycle bin", etc...

You may want to reinstall the operating system.

Backupthe files that are importantto you before you reinstall.

The "New" installation will overwrite the current one

If you do not format your hard drive before the reinstall the installation should not harm your files (That's why I suggest backingup your files) and will speed up the installation process.
 

Read other 1 answers
RELEVANCY SCORE 204

Hi:

Looking for insight/advice re: KB3054476.

According to Infoworld, it was "Optional" in May, but I was not offered it then.
This week, it was offered as "Important" and "Recommended" (!), but only for one of my 2 Win7/64 boxes.

I have read the MS KB article, as well as THIS FORUM THREAD, the latter of which includes a report of a BSOD due to this particular update.

However, there isn't much out on the web about it.
And most of the discussion about it is overly technical for me.
And I am confused as to why it was previously offered as "Optional", but now is "Important" or "Recommended".

I don't *think* I "need" it (as I have no webcam on this box). And I don't like to tempt fate by fixing things that are not broken.

So, 3 questions:
Is it safe to install?
Is it really necessary/important?
Or would I be OK to hide it?
Thanks very much in advance!

A:KB3054476 offered as "Important"/"Recommended"/"Optional"

The status of updates changes with circumstances.
If an update isn't relevant, it won't be offered at all.
If however it's relevant but the related software is not apparently in use, it may be 'optional' - and gravitate to 'Recommended' or 'Important' if the related software is in use.
It can also be promoted through the hierarchy by MS depending on feedback through WU and error-trapped feedback.


If you have (and use) a webcam, then it's probably best to install the update.

Read other 4 answers
RELEVANCY SCORE 204

Guys,

I am a little confused with regard to some of the mail options in Outlook Express. (I have version 6) What is the difference between the "Drafts" and "Outbox" folders?

Further how does the "Send Later" option work from the file menu? I always thought that "Send Later" was the same as using "Drafts" but what happend was that I was doing an e-mail, went to Drafts, or clicked on "Send Later" or Outbox and then after I clicked on "Send" doing a regular send, I checked my Sent folder and about 3 copies of the same message were delivered to the same person! (I only sent one message-not 3!)

What is the deal with the "Outbox" folder? Apparently that is not like the Drafts folder....correct?

What's the difference between doing a Save, Save As, and Send Later with regard to OE functions? If I want to save a message that isn't done yet, which of these 3 options should I use? (I.e, I want the message to go to the Drafts folder for example and stay there until I TELL OE to send it.) I think whatever I did above was that I modified my message and then click on where it just automatically sent next time I opened the message. A review of these features would be helpful!

Just for the record, I also use Yahoo Mail and find that so much easier!

Jack
 

A:Please Review OE "Send", "Drafts", and "Outbox" Options

Jack
To save an E-Mail to your Drafts folder for work on later then you use the File\Save option.
If you wish to save the E-Mail in another format such as .EML or .TXT or .HTM then you use the Save as function. You will also be required to specify a folder to save in or use its "My Documents" default.
Send later function if only one e-mail account exists will place the e-mail in the outbox and send it the next time you click on the send receive button. If you have multiple accounts then you can specify which account to send it from.

Dave
 

Read other 2 answers
RELEVANCY SCORE 204

I have a 7200rpm hard drive that shows up as 3 separate partitions on my MacBook Pro desktop. They are "System Reserved", "Untitled 1" and "Untitled". When looking at them in the Disk Utility program, they show up as "System
Reserved",  "disk2s1" and "disk2s3". I can't seem to find a way to wipe the drive and just have 1 partition. I don't need to save anything on it so it can all be deleted and consolidated. Not sure if this helps but the previous
owner told me that he had accidentally erased another partition that prevented the hard drive from being reconsolidated. It also may have been a Windows boot drive. Any help in restoring this hard drive would be appreciated. Thank you.

Read other answers
RELEVANCY SCORE 204

OK.....
As I said I am new.....
Hope this info is the way you need it.
MANY MANY THANKS IN ADVANCE FOR THE TIME & HELP !!!
Check out the following .....HHEELLLPPP


Logfile of HijackThis v1.98.2
Scan saved at 12:38:36 PM, on 11/12/2004
Platform: Windows XP (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 (6.00.2600.0000)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\system32\logonui.exe
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\Explorer.EXE
C:\PROGRA~1\mcafee.com\vso\mcvsshld.exe
C:\WINDOWS\System32\Promon.exe
c:\program files\mcafee.com\agent\mcagent.exe
c:\progra~1\mcafee.com\vso\mcvsescn.exe
C:\Program Files\interMute\AdSubtract\AdSub.exe
C:\PROGRA~1\VCOM\Fix-It\mxtask.exe
c:\PROGRA~1\mcafee.com\vso\mcvsrte.exe
C:\WINDOWS\System32\NMSSvc.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\System32\MsPMSPSv.exe
C:\Program Files\McAfee.com\VSO\mcshield.exe
C:\PROGRA~1\VCOM\Fix-It\mxtask.exe
C:\WINDOWS\System32\wuauclt.exe
C:\Documents and Settings\Frank M. Gazzo\Local Settings\Temp\Temporary Directory 1 for hijackthis.zip\HijackThis.exe

R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://www.dellnet.com
R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Bar = http://websearch.drsnsrch.com/sidesearch.cgi?id=
R1 - HKCU\Software\Micro... Read more

A:NEW THREAD / "xads", "xlime", "Context3.kanoodle"

hi

how to create a folder ?

right click anywhere in your desktop
click new,a tab opens ,click folder ,name it hjtantivirus .

download again hijackthis and install it in the new created folder .

your hjt is here now
C:\Documents and Settings\Frank M. Gazzo\Local Settings\Temp\Temporary Directory 1 for hijackthis.zip\HijackThis.exe

it will not work properly if it stays there .

and don t create a new thread ,keep only one thread .this one ,now .

Read other 1 answers
RELEVANCY SCORE 203.6

First things first, thanks to all who can help.....





I need to programmatically make some adjustments to the Internet Explorer security settings. Most of these settings I have found but there are a few I have not been able to get a clear exact location for in the registry. I will be using a .BAT file to make
the adjustments on 100+ PCs.





Here is what I am looking for.....





Under the "Internet  Properties" found in control panel, under the "Privacy" tab there is an "Advanced" option button. When I click on it I get an "Advance Privacy Settings" options box. On it are several settings.
The first setting, "Override automatic cookie handling" needs to be checked in order to access the other options. I can do that by adjusting the DWord value of "PrivacyAdvanced" under the "Internet Settings" key in the registry,
"HKCU\Software\Microsoft\Windows\CurrentVersion\Internet settings", to be specific.





What I have not been able to find are the registry entries for the "First-party Cookies" "Accept, Block, or Prompt" options, the "Third-party Cookies" "Accept, Block, or Prompt" options, and the "Always allow
session cookies" check box. Please see picture below....















I have seen references to the following settings as being where those options exist, but nothing that explains ... Read more

Read other answers
RELEVANCY SCORE 202

Hi, I am having a problem with my newer computer, I just got this rig a few months ago and never had a problem until last Thursday. It Blue Screened on me while I was installing ARC GIS 10.1. From then on it randomly crashes. (I have previously installed ARC GIS 10 and never had a problem.)

I keep things updated (windows and drivers) and I do think windows forced through an update earlier that day. I un installed ARC GIS 10.1 and the windows update, didn't make any difference. I have also ran the Windows Mem test and Auslogic BoostSpeed/ Registry repair. I keep getting "Bad Pool Header" and "Page In Nonpage Area" and I can't seem to find something that triggers it. So far it hasn't crashed in Safe Mode without network access. I tried it once with access and it crashed. Currently have windows checking the drives for errors ( I have 4).

I think I attached the proper dump files. This is my work computer so this is kind of causing a big problem. Thanks in advanced for the help!!

A:BSOD "Bad Pool Header" and "Page In Nonpage Area" Runs in Safe Mode

Welcome aboard.

The crash dump you supplied, suggests the display driver failed there.

Code:
fffff880`0c995858 fffff880`10018000Unable to load image \SystemRoot\system32\DRIVERS\nvlddmkm.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
nvlddmkm+0x980000
Go to Drivers - Download NVIDIA Drivers, follow option two to search for the appropriate driver for your system automatically, and install it.
Let us know how it worked.

Read other 3 answers
RELEVANCY SCORE 200.4

Hello, i've been having this problem for a week now, tried to fix it but no luck what so ever. So i got tired and i am looking for your assistance on this matter.
Every time I play Aion online, in about 10-30mins i get a blue screen saying "REFERENCE BY POINTER" or "IRQL NOT LESS OR EQUAL", tried many methods that were stated on the forums of different sites but no luck... that is why i am attaching my BSOD information and hoping for you assistance. Thank you in advance.
PS: When I play Aion, and the PC restarts (caused by BSOD) most of the time the minidump isn't created and sometimes it doesn't go into the BSOD it just restarts, but i know the problem is the BSOD.

I have Windows 7 Ultimate x86(32bit)
It's the original installed OS on my system (OEM)
I've had this computer for ~4years, drivers always up to date and i reisntalled my Windows yesterday.
Attaching the Zip file with the information required which was on BSOD posting instructions post.

A:BSOD playing Aion, "REFERENCE BY POINTER" and "IRQL NOT LESS OR EQUAL"

No DMPS included in upload try this method.

We do need the DMP file as it contains the only record of the sequence of events leading up to the crash, what drivers were loaded, and what was responsible.

If you are overclocking STOP
We could also use some system information, which you can get easily by running msinfo32.
To do that go to start>run>type msinfo32>enter

When it is finished running go to file>save>name it and upload to us here.
You may be able to get the DMP files without crashing by booting into safe mode (F8) with networking.

To enable us to assist you with your computer's BSOD symptoms, upload the contents of your "\Windows\Minidump" folder.

The procedure:





Quote:
* Copy the contents of \Windows\Minidump to another (temporary) location somewhere on your machine.
* Zip up the copy.
* Attach the ZIP archive to your post using the "paperclip" (file attachments) button.
*If the files are too large please upload them to a file sharing service like "Rapidshare" and put a link to them in your reply.



To ensure minidumps are enabled:





Quote:
* Go to Start, in the Search Box type: sysdm.cpl, press Enter.
* Under the Advanced tab, click on the Startup and Recovery Settings... button.
* Ensure that Automatically restart is unchecked.
* Under the Write Debugging Information header select Small memory dump (256 kB) in the dropdown box (the 256kb varies).
* Ensure that the Sma... Read more

Read other 9 answers
RELEVANCY SCORE 200.4

Problem:

Everything was running fine until yesterday, when my PC crashed with the BSOD giving me the "IRQL not less or equal" error. I ignored it and carried on- which resulted in the computer crashing with "Memory management" blues whenever I started something that was not the browser (It later started crashing on browser start too).

I first thought it was the temperature - Memtest95 and GPUtemp said otherwise.

So I started testing the RAM (taking one DIMM out) with Memtest86- It passed 4 cycles, so I shut the PC down and put the other DIMM in.

When I turned the PC on again, there was no signal sent to my screen, and none to my keyboard (and the HDD light on the front of the case did not start blinking like usual). The fans were running, so I figured something might be wrong with the DIMMs I put in. I removed the graphics card and plugged the screen into the motherboard.

Now the screen gets a signal, background lighting starts up, and then it shuts down to hibernation again. This repeats itself until the machine is shut down manually.

I got no idea what to do.

System specs: http://pastebin.com/DQwejZLx
I can not post the Minidump folder, since the PC can't start and I did not back it up. Sorry.

Thank you for your help.
 

Read other answers
RELEVANCY SCORE 200

For the past two days I've been getting BSOD while playing games. This only occurs while a game is open and sometimes the blue screen doesn't even come up, the pc simply restarts and comes up with the pop up like it does when you get a BSOD.

It first occured when I upgraded to windows 10 (from win7), naturally I downgraded to win7 however the usb drivers became corrupt and therefore I had to clean install win7. After doing so the same problem occured giving a BSOD with this in the dump file:
(1st crash ) Imgur: The most awesome images on the Internet
(2nd crash ) Imgur: The most awesome images on the Internet

After seeing this I fresh installed windows again and the problem is still occuring, Ive tried installing older graphic drivers however that made no difference (im currently running the drivers that came on a cd with my pc).

Here are my specs: Imgur: The most awesome images on the Internet
In the attachments is the file produced by SysnativeBSODCollectionApp.

Any suggestions as to the source of the problem or solution greatly appreciated.

A:BSOD causing by "dxgkrn.sys" and "ntoskrnl.exe""

[Update] Because the forum won't allow me to edit the post anymore.
Before the actual "crashing"/BSOD starting I was getting errors saying "The display driver has stopped working and recovered" and "Application X has been blocked from using graphic software". This was all happening while playing cs:go. After a while of restarting csgo and continuing to play for about 5 min before it crashed again it just started restarting or the monitor went blank and the pc stayed on forcing me to hold the power button to restart it.
The BSOD/black screens/restarts mostly happen while playing games however they sometimes occur while browsing or when the computer is simply on without anything (but the antivirus) running.

Read other 1 answers
RELEVANCY SCORE 199.2

Hello everyone
I have this problem for more than 3 months for now...

The INSTRUCTION AT "0x00a96ce0"referenced memory at "000000000" couldn't be written".

That's always what i get when i restart my computer,just before screen goes dark.
I believe that it has to do something with Microsoft updates.The reason i believe this, is that i once reinstalled my PC and didn't have any problem until i didn't update my PC.
And i posted here that thinking my problem was solved but unfortunately i was wrong.

Please if you have any tips on this one let me know it would be greatly appreciated.

Thank you!
 

Read other answers
RELEVANCY SCORE 199.2

Hi Guys, any ideas how to access my external hard drive [TOSHIBA MK3029GACE] device manager can see it but it does not appear in disc management.

I use this HDD perfectly in my car HDD player. But when I try to connect it to my Laptop, it does not show up in disk management.

Please check the attached screen shot..

Thanks for the help....

A:HDD shows in "Device Manager" but not in "DiskPart"or" Disk Management

Specs show that drive has a ATA-6 interface (P-ATA, or IDE). How are you connecting this drive to your laptop? Does the laptop have a PATA or SATA connection? Does it use an adapter?

Read other 1 answers
RELEVANCY SCORE 198.4

I have been getting the BSOD since a few weeks and found out by trial and error that a USB-hub is causing the problem. Whenever I disconnect the hub before I shut off the computer I do not get the blue screen.
Yesterday I also got a BSOD that mentioned driver power state failure. After I had de-installed Ubuntu 10.04 (I wanted to see what people are talking about but did not really like it) that problem did not show up again, although I do not know if that is just coincidence.

I have enclosed the dump files as per your instructions and hope that somebody will be able to help me.
Thank you.

A:BSOD with "usbhub.sys" and "driver power state failure"

Welcome!

It does look as if your USB drivers are causing the issue.
BSOD BUGCHECK SUMMARY
Code:

Built by: 7600.16539.x86fre.win7_gdr.100226-1909
Debug session time: Wed Apr 28 03:41:32.255 2010 (GMT-4)
System Uptime: 0 days 0:31:47.502
BugCheck 1000007E, {c0000005, 9482319c, ad39bb40, ad39b720}
*** WARNING: Unable to verify timestamp for libusb0.sys
*** ERROR: Module load completed but symbols could not be loaded for libusb0.sys
Probably caused by : libusb0.sys ( libusb0+428c )
PROCESS_NAME: System
BUGCHECK_STR: 0x7E
??????????????????????????????????????????????????????????????????????????????????????
Built by: 7600.16539.x86fre.win7_gdr.100226-1909
Debug session time: Mon May 10 03:46:15.009 2010 (GMT-4)
System Uptime: 0 days 0:00:15.272
BugCheck 124, {0, 8752f544, 0, 0}
Probably caused by : hardware
BUGCHECK_STR: 0x124_GenuineIntel
PROCESS_NAME: System
??????????????????????????????????????????????????????????????????????????????????????
Built by: 7600.16539.x86fre.win7_gdr.100226-1909
Debug session time: Mon May 10 05:22:31.146 2010 (GMT-4)
System Uptime: 0 days 0:02:23.393
BugCheck 1000007E, {c0000005, 9444b19c, adb53b40, adb53720}
*** WARNING: Unable to verify timestamp for libusb0.sys
*** ERROR: Module load completed but symbols could not be loaded for libusb0.sys
Probably caused by : libusb0.sys ( libusb0+428c )
PROCESS_NAME: System
BUGCHECK_STR: 0x7E
??????????????????????????????????????????????????????????????????????????????????????
Built by: 7600.16... Read more

Read other 5 answers
RELEVANCY SCORE 198.4

Hi

New installation of windows 7 ultimate 32bit and on trying to copy a 38gb folder from c drive to d drive, pc gives bsod.
Lately playing world of tanks is resulting in system lock ups,please can anyone help

Frosty

A:bsod copying files from "c" to "d" drive and system lock ups

Post it following the Blue Screen of Death (BSOD) Posting Instructions.

Read other 2 answers
RELEVANCY SCORE 198

Hi all
Previously the  "Save Picture"  box would put a web generated title in the box and automatically selected JPEG.  Now the title box reads "untitled" and the only file options offered are "png" & "bmp" 

Please note that a similar post has appeared, but the solution did not match the fault.  I'm seeking to restore the automatic response to save picture, that might have been upset by antivirus clean-up programme.

Thank youin advance for considering my problem

Read other answers
RELEVANCY SCORE 197.2

How do I change the font of "Welcome", "Logging Off" and "Shutting down"? Is it hard coded in a uifile? Which file are the words in? Is the file written in XML?? John

A:Change font of "Welcome", "Logging Off" and "Shutting down"?

  
Quote: Originally Posted by RBCC


How do I change the font of "Welcome", "Logging Off" and "Shutting down"? Is it hard coded in a uifile? Which file are the words in? Is the file written in XML?? John


I am not sure you can change the fonts though if you wish you can change the text from "Shutting Down" to "Bye Bye" or so, by editing, winlogon.exe.mui.

Read other 3 answers
RELEVANCY SCORE 197.2

OK...
I'm looking for some help getting rid of theses creeps!
I have tried several programs including Spybot, Spyblaster, Lavasoft, Mcafee, etc. etc. with no luck.
I'm new to HijackThis but here we go..... ]

Logfile of HijackThis v1.97.7
Scan saved at 11:59:09 AM, on 11/12/2004
Platform: Windows XP (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 (6.00.2600.0000)SIZE=5]

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\Explorer.EXE
C:\WINDOWS\system32\spoolsv.exe
C:\PROGRA~1\mcafee.com\vso\mcvsshld.exe
C:\WINDOWS\System32\Promon.exe
c:\program files\mcafee.com\agent\mcagent.exe
c:\progra~1\mcafee.com\vso\mcvsescn.exe
C:\Program Files\interMute\AdSubtract\AdSub.exe
C:\PROGRA~1\VCOM\Fix-It\mxtask.exe
c:\PROGRA~1\mcafee.com\vso\mcvsrte.exe
C:\WINDOWS\System32\NMSSvc.exe
C:\WINDOWS\System32\svchost.exe
C:\WINDOWS\System32\MsPMSPSv.exe
C:\PROGRA~1\VCOM\Fix-It\mxtask.exe
C:\Program Files\McAfee.com\VSO\mcshield.exe
C:\WINDOWS\System32\wuauclt.exe
C:\Program Files\Internet Explorer\IEXPLORE.EXE
G:\HijackThis.exe
G:\HijackThis.exe

R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Bar = http://websearch.drsnsrch.com/sidesearch.cgi?id=
R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://websearch.drsnsrch.com/sidesearch.cgi?id=
R1 - HKCU\Software\Mi... Read more

A:(I'm new here) help w/ "xads", "xlime", "Context3.kanoodle"

hi pdx

please download the new hijackthis from here
http://www.majorgeeks.com/download3155.html


and install it in it s own folder like this :

C:\hjtantivirus\hijackthis.exe

scan again with the new hjt and post a new log .

Read other 1 answers
RELEVANCY SCORE 197.2

Hey guys. This morning I got a really strange error code. When I tryed to update Steam on my PC, this error message popped up;

"The instruction at "0x00172058" referenced memory at "0x00d1004". The memory could not be "read".

Click OK to terminate the program.

Lately, I have'nt been able to install WoW either, I install it all the way to 100% and then when I try to launch it, I obviously have to re-download all the patches but it prompts me that I have to install it again, even though it is all there.

Tryed downloading the full game digitally off of wow-europe.com too, I click run to get it started, nothing happens and then this message pops up.

"The instruction at "0x00182058" referenced memory at "0x0f070014". The memory could not be "read".

Click OK to terminate the program.

I don't know what's up with it. My freind told me to run a CHKDSK /R to see if there was anything wrong with my drive and it ran smoothly, although I must say it took about an hour or so.

So, that was complete, tryed to do it again and I still kept getting these error messages. But I saw something on my desktop that wasn't there previously. It is an error log. Here is the error log;
#
# An unexpected error has been detected by Java Runtime Environment:
#
# EXCEPTION_ACCESS_VIOLATION (0xc0000005) at pc=0x6d5ecb6d, pid=1584, tid=1248
#
# Java VM: Java HotSpot(TM) Client VM (11.0-b16 mixed mode, sharing wi... Read more

Read other answers
RELEVANCY SCORE 197.2

Recently after updating Windows 10 to Fall Creators Update (1709) (I think this started to happen after clicking the "forgot password" button on the sign in screen, just a theory), all messages on the shutdown/boot screen in Windows (for example "Shutting down", "Restarting", "Welcome", ...) became replaced with "Just a moment". It isn't a huge inconvenience, but "Working with updates" also got replaced by it, so I don't know if the computer is installing updates or is stuck at shutting down for example if it takes a long time.
I don't expect anyone to have a solution, I'm just wondering if someone else has this problem. SFC and DISM didn't help me, changing the system language did not help.
 

Read other answers