Over 1 million tech questions and answers.

"Preparing Automatic Repair" Doesn't work

Q: "Preparing Automatic Repair" Doesn't work

My laptop (Predator Helios 300, i7-7700HQ, 16Gb DDR4, GTX 1060, 256GB SSD + 1TB HDD) doesn't start up for some reason. So I wanted to start it in safemode so I can backup my crucial data before formatting my pc. When it started "Preparing Automatic Repair" it went to a black screen with only the mouse cursor. It doesn't get further than that. If I repair or reinstall Windows 10 using a flash drive, will I loose my original license key?

Read other answers
RELEVANCY SCORE 200
Preferred Solution: "Preparing Automatic Repair" Doesn't work

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

RELEVANCY SCORE 121.6

Hi, my Lenovo laptop has had a virus in it for quite a while and I recently did a factory reset, (I wasn't trying to get rid of the virus, I was just trying to clean out my old files) and it shut off. I turned it back on after I thought the reset had finished and all that came up was a black screen with the words Lenovo and it said "preparing automatic repair", and would go to another screen and say "diagnosing your pc". It would stay in a constant loop. I haven't been able to fix it on my own, any ideas?
 

Read other answers
RELEVANCY SCORE 118.8

Earlier today, I noticed that my laptop wasn't automatically adjusting its screen brightness. I often fixed this recurring problem by putting the laptop in a state where the screen would turn off. I decided to quick press the power button to quickly put my laptop into sleep mode. However, the computer's internals were still operating, so I forced the computer to shut down. When I logged back in after I re-booted the computer, I was greeted by a window that said that the hardware settings had been changed and that the computer required a restart, so I obliged. When I rebooted the computer again, I was met with a boot screen that said "Preparing Automatic Repair." My computer loaded to the "Your PC did not start correctly. This can usually be repaired with a restart." I have not been able to load the OS proper. Please help!
 

Read other answers
RELEVANCY SCORE 118.8

I have a Satellite U50D-A and when I turned it on thismorning it starts on the "Toshiba leading inovation screen" with Preparing Automatic Repair written on the bottom. I've googled it but everyone else has the same problem but stuck in a loop...mines just frozen on that first screen. Now been 9 hours and am starting to doubt it will automatically repair

Read other answers
RELEVANCY SCORE 118.8

I have a Satellite U50D-A and when I turned it on thismorning it starts on the "Toshiba leading inovation screen" with Preparing Automatic Repair written on the bottom. I've googled it but everyone else has the same problem but stuck in a loop...mines just frozen on that first screen. Now been 9 hours and am starting to doubt it will automatically repair

Read other answers
RELEVANCY SCORE 118

Hi, after sifting through many threads about this problem I'm still not getting anywhere. I can run recovery from the boot menu but it goes nowhere. I have a recovery CD and a USB but when I choose them in the boot menu nothing happens. I also disable secure boot. I don't care about the data at this point, just want it to boot up. Any suggestions would be appreciated.
 

A:Toshiba P75 "preparing automatic repair" loop

You appear to have a Toshiba Satellite P75 series laptop.

What is its complete model number?
(A dash and additional characters after P75 comprises the complete model number)

What "recovery CD and USB" are you referring to?
Did they come with or were they created in that laptop?

---------------------------------------------------------------
 

Read other 1 answers
RELEVANCY SCORE 118

Hello My xps 8930 i7 (new) is stuck on "preparing automatic repair" and stays there even after several reboots and several goes via the recover os assist option. We turned the desktop on today and this problem occurred, it was working ok yesterday. The only thing that was different was I added some firewall rules to the sky router which I have since removed and the same problem persists. I have also tried going to windows recovery from os assist and that hangs with "Please wait".I have already run Running the ePSA diagnostics - no issues and I have already run recoveryassist OS - this found and fixed a problem with the partition, but the same issue occurs.I did not receive a windows install CD with this. Is my only option to reset to factory settings ? I hope not.
Thanks
Dave

A:"preparing automatic repair" XPS 8930 desktop

You could use Microsoft's Media Creation Tool to repair your Windows 10 OS.

Read other 1 answers
RELEVANCY SCORE 116.8

Dell Inspiron 3541 laptop, 15.6" screen, Win 8 OS. (April, 2014)
Service Tag: F12R412
CPU: AMD A4 - 6210, APU with AMD Radeon R3 graphics.
CPU Speed: 1800 MGz
CPU ID:730f01
HD: 500 GB
RAM: 4 GB

It starts, shows Dell logo, then says: Preparing automatic repair. Dotted progress circle begins, then shows a rectangular box for a split second. Then it moves back to a black screen and doesn't progress. Maybe I'm not waiting long enough. How long should it take?

The cursor arrow stays visible and moveable when I touch the pad.

Just found this one tonight. It's a nice machine. Can it be repaired?
 

Read other answers
RELEVANCY SCORE 116.4

I have had my Dell Inspiron 17 5758 Laptop since around Feb 10, 2015 so almost 2 years now.  The lap top was working fine up until mid day yesterday now it is stuck in the "preparing sutomatic repair" loop and ends with either a black screen, saying my laptop didnt start correctly or that it couldnt repair my laptop and when i try to run a diagnostic on it it says that my hard drive is not installed. Also now the hard drove is simply not running. Is this because the hard drive as failed? Its in transit a lot and occasionnaly hits a bumps on the seat of my car when driving.
Also if i have to buy a new hard drive how would i install windows 10 on my laptop again? Will i have to pay for it again?

Read other answers
RELEVANCY SCORE 98

Hi there,
I purchased a hp pavilion laptop a few months ago with Windows 10 pre-installed.
I haven't used it for a few days, turned it on this evening and I got a message on boot up saying
"preparing automatic repairs" and then my screen goes blank 3-5 seconds later.
I do not have a cursor and have tried various keys and different ways of trying to bring up some kind of option. I also tried plugging my laptop into my TV to see if it were perhaps the screen that was going wrong. To no avail, I have spent hours on Google trying to work this out and I have absolutely no idea what to do next as I seem to have no other option!

I really really hope someone can help me!!

Thank you in advance.

Gibsonuk

A:"preparing automatic repairs" Then bsod

Hi Gibsonuk.

We need at least some information about the BSOD in order to know what is going on there. Can you take a camera snap of it and let us see it?

Read other 0 answers
RELEVANCY SCORE 96.4

My laptop is stuck in a cycle of restarting itself after displaying a screen that says "Preparing to Repair". It turns on, shows the hp symbol and the message, then after a few seconds it loads a black screen covered in blue dots (which I've never seen before), then it turns itself off and restarts the cycle. I've tried using the fkeys, which load every option except the f12 system repair option. I can get into my bios menus and everything. I made a repair usb, as my laptop doesn't have a disc tray, I changed the bios to run from the usb in hopes that I could repair it that way. Still not working. Does anyone have any thoughts or suggestions? I don't care if I have to completely wipe it clean. I just don't know how at this point.
 

Read other answers
RELEVANCY SCORE 94.4

2010 06 05

This is a question for information about why my networking problem finally was resolved.
I have four PC?s on my network; one Windows 7 and three Windows XP. The Windows 7 PC always sees all three of the other computers. However the Windows XP computers sometimes don?t see the other XP computers when I press ?My Network Places.? Quite by accident I discovered that if I press ?View Workgroup Computers? then ALL the other PC?s in the network DO show up. Furthermore, if I click through "View Workgroup Computers" and access/edit a file on one of the other computers, then this computer will ALSO show up in ?My Network Places.? This behavior seems to be quite consistent and works every time I have tried it. Apparently, this is a workaround to the long vexing problem of why my networked PC?s sometimes don?t show up under ?My Network Places.?

My question: why does ?View Workgroup Computers? apparently always show all the networked PC?s, when ?My Network Places? does so only intermittently or sometimes not at all?

Thanks for any response.

Read other answers
RELEVANCY SCORE 90

I have a Lenovo G500S Touch running Windows 8.1. I am stuck in the endless loop, which I've researched and still haven't found a solution. For many hours, all it would do is just show a black screen with "Lenovo" on it. Then it went into this loop, and nothing I do can get out of it. Help??
 

A:Lenovo laptop stuck in "Automatic Repair loop"

Note: I can get the "Startup Settings" screen, but following that, I CANNOT get the options to select; so I can't select, say, Safe Mode, or whatever.
 

Read other 1 answers
RELEVANCY SCORE 90

Hi there,

This is my first Dekstop PC I have built myself. Here is some information:

OS - Windows 8.1 x64 (Only OS - Purchased from retailer)
System Age/OS Age - 2 Months
CPU - i7 4790k (I haven't OC'd it)
GPU - GTX 980
Motherboard - MSI z97 Gaming 7
Power supply - Corsair CP-9020054-UK RM Series RM650 80 Plus Gold 650W
RAM - Crucial Vengeance low profile DDR3 1600mhz 16GB

I also have 4 hardrives (1 3TB, 3 1 TB) and 1 SSD (Crucial 256GB) (my OS is installed on the SSD)

System Manufacturer - MSI?

The problem:

Working fine for 2 months (no issues). Today I started the pc and I went away to do something else. Came back to a black screen (which had some backlighting). I moved the mouse and typed something and the screen didn't change and I assumed something had crashed so I restarted (held down power button)

I attempt to restart only for the PC to get into a loop of restarting exactly when the blue windows logo appears and then I get the windows 8 BSOD (sad white face) but I can't read the error as it restarts too fast.

It then attempts to repair and gets to the "Preparing automatic repair" before the whole "Windows has encountered a problem and needs to restart" BSOD.

Tried removing all cables (Everything except PSU cable) - No effect. Computer still restarted continuously.

I have made no recent hardware modifications.

Thanks,

~ Brya

A:Computer worked fine for 2 months. Now gets BSOD on "Prepairing automatic Repair"

Looks like one of my memory sticks seems to be at fault. Tried a single stick and it worked fine. Tried the other "bad" stick and the problem occurred again (computer just froze).

Tried using both sticks with good stick always in slot 1 and the bad stick in 2,3,4 and problem occurs as normal.

Why and how did this occur? It was working fine 3 hours ago with both sticks until I put the computer to sleep. After that, the problem started...

Another problem now is that using the single "good stick" causes the pc to load fine except it doesn't display the login information and just displays a bright blue screen. I have to press the power button (which I have set to sleep) and then press it again to resume in order for windows to display the login information (i.e. resuming the pc caused it to show my account name and ask for my password etc)

Why do I have to do this? should I run automatic repair? I'll probably try running repair anyway.

Read other 1 answers
RELEVANCY SCORE 89.6

Looking a for some guidance here. I have a Toshiba Satellite C55t-A5222 laptop that went into the dreaded "Automatic Repair Loop". I attempted to boot in Safe Mode to go from there. Upon rebooting (in Safe Mode), my laptop remained at the "Please wait" screen with the spinning dots for hours. After another hard reset, I attempted to boot it up again. This time with a recovery thumb drive I made from from my son's desktop. Same thing.... "Please wait" for hours. Frustrated, I decided to boot up in system recovery by holding down "0" while powering up the laptop. Same thing..... "Please wait". I am at my wits end and know of nothing else to do. The laptop will not boot past "Please wait" now. I am running Windows 8.1 but unsure of which version (32 or 64 bit). Any help would be greatly appreciated.

A:1st Automatic Repair Loop & now stuck at "Please wait"....

Any help would be greatly appreciated.



Have you tried restarting it shutting off 3 or 4 times quickly to get advanced boot options ?

Read other 2 answers
RELEVANCY SCORE 89.6

I posted this in wrong forum, in "security". So, I am re-posting it here.
Hello, I would appreciate help fixing my PC. System: Toshiba C75D-B7300, Windows 8.1. For a few weeks the pc was running slow. It would freeze frequently. Initially the mouse would be stuck for a while and then resume. It was like every keystroke took several
minutes to execute. Then it started freezing to the point where i had to restart to get out of it. Then it became so frequent that it became impossible to use the PC. The problem existed both in normal mode and in safe mode.

I have not installed any new programs before this began. I tried restoring to previous date, but it said "failed".
So, I looked up solutions on line and tried them. scannow, chkdsk, etc. (scheduled at restart) The results showed "errors were found, some errors could not be fixed". Every method I found on line I tried. After one of the methods, and I believe
it was some version of scannow.exe  with several alphanumeric /. After running that, the PC is stuck in a "automatic repair loop". The PC has been on for two days and I can see the windows go through  "preparing to do automatic repair",
"repairing disk errors: this may take over an hour" etc over and over for two days. Finally I turned the PC off from the power button. Then restarted the PC. Now I am unable to go to the start options to get into safe mode (it did before this loop)
and it goes ... Read more

Read other answers
RELEVANCY SCORE 89.6

I recently built a new computer and installed Windows 8.1 64-bit on it. One day, the computer took a very long time to boot up, was very slow, and was stuck on the "Logging In" screen. I shut down the computer by holding down the power button (was this a mistake?), and turned it back on. It went into the Automatic Repair, then to the "Diagnosing Your PC" screen, and took me to the menu with different options to fix the computer. I selected the Troubleshooting option, and the computer froze. I decided to put the installation disc back in to reinstall Windows 8.1, and after that, everything was fine for about a week. Then, the same thing happened AGAIN. I have no idea why this is happening. Before running Windows 8.1, my computer ran the Windows 10 Technical Preview. With it, the computer crashed twice and went into the Automatic Repair loop. Before running the Windows 10 Technical Preview, my computer ran Windows 7 flawlessly. Any advice? Could my trail of problems have started with Windows 10?

System Specs:
Nvidia Geforce 660 (Graphics Card)
MSI A78M-E35 FM2+ (Motherboard)
Crucial Ballistix Sport 16GB Kit (RAM)
AMD Athlon 760K Multicore Processor
Western Digital 1 TB SATA III Hard Drive
Corsair Builder Series CX 430 Watt Power Supply

A:Windows 8 crashes and enters "Automatic Repair" very often

Any advice?



Unless someone has better advice, if it was mine I would reinstall my OS.

Read other 8 answers
RELEVANCY SCORE 88.8

i tried to clone a backup hard drive to my computer and canceled the operation about halfway through because it was taking way too long. Now my computer is stuck in a "preparing automatic repair", "diagnosing your PC", and then "repairing disk errors", then restart loop
 

A:Stuck in "automatic repair" loop

I have an Asus motherboard and bios, and I'm on a desktop 64 bit Windows 10
 

Read other 2 answers
RELEVANCY SCORE 86

Hello. I have an ideapad z580. It was functioning pretty well until I travelled to China. It started freezing randomly, didnt restart for approx 10 min etc. And finally today it crashed after I restarted it. I can't reach windows, it says preparing automatic repair, and fails, giving a screen says "a required device isnt connected or cannot be accessed". And adds that I need to use recovery tools. I didn't get any cds because of OKR. I restarted with the novo button. Selected recovery. 'Loading files' appeared, waited nearly 5 min and a blue screen with a sad face appeared. So I can't reach windows, cant recover it, in another country with nothing but a smartphone and internet connection. I didnt install any softwares, updated my OS to windows 10 a month ago. If there is a solution Ill be glad because I need the pc and my documents in the following days. Thank you for your help. 

Read other answers
RELEVANCY SCORE 85.6

Hello, all?

Have been fighting (and losing!) a problem with my Win7 32-bit Home Ult SP1 no longer being able to accomplish Windows Updates. Got much assistance from NoelDP in the appropriate venue, but the problem seems not to be solvable in an elegant way.

The options that seem left are Repair Install of Win7...and clean installation of Win7 and all applications/patches/updates/etc. I'm struggling to avoid the clean install.

I've cloned my primary system drive to an alternative drive, and that clone starts into Win7 just as the primary drive. (It replicates the "No updates for you!" problem, of course.)

So far, I've been unable to get the Repair Install to work. I read the tutorial, downloaded the correct Win7-SP1 ISO, burned it to disk.

After starting Win7 from the drive I want to be "repair installed" and launching Setup.exe from the DVD (as an Administrator), I get the familiar blue "Install Now?" dialog. Clicking assent segues to the expected "Setup is copying temporary files" screen and expected HD activity, then the expected "Setup is starting" screen. After a second or three of "Setup is starting," the process stops (w/o explanation) and loops back to the "Install now?" dialog.

FWIW, I've also copied the DVD's files to a separate folder on another drive that's available and have mounted the ISO in a virtual drive. Trying these two sources gives the same result as described in paragrap... Read more

A:Win7 Repair Install "Loops" and Doesn't Run

When was the last time you had a reinstal similar to the perfect one compiled here? Clean Reinstall - Factory OEM Windows 7
If the answer is never then it couldn't be more clear that you are overdue since you have massive corruption that causes almost nothing important to work right.

Did you run SFC /SCANNOW Command - System File Checker

Did you uncheck everything in msconfig>Startup and then >Services after Hiding all MS Services, then try Repair Install?

Try uninstalling your AV.

Read other 3 answers
RELEVANCY SCORE 85.6

Hello,

I have a recovery partition on my Dell windows vista 64x inspiron computer but when I press the F8 key there is no option for "repair computer" or anything like that. How do I restore it to factory settings using that image?

Thank you,

Jane

P.S.

when I tried getting the recovery screen from the neosmart boot disk i clicked "restore computer" to factory settings and it scanned and said it "couldn't find a valid recovery location" but if I'm in windows I can go to my computer and clearly see a recovery partition so I know one is there or at least WAS.

is it possible that it got corrupted or do I need to change some setting to make it work. Thanks.

A:F8 doesn't offer "repair computer" option

Hello again Jane.




Be sure to post back so I know if this is still correct.





Here are the recovery instructions from Dell.

1. Reboot, and press Ctrl + F11 at the Dell logo.
2. The Dell™ PC Restore by Symantec screen will come up.
3. Select "Restore" or use the Tab key to highlight it and press Enter.
4. if you wish to continue, click "Confirm", or use the Tab key to highlight it and press Enter.
5. When the utility is finished, click "Finish", or use the Tab key to highlight it and press Enter.

Read other 10 answers
RELEVANCY SCORE 84.4

Hello Guys and Girls,

My wireless internet connections are currently set to a manually configured status, but this means I am having problems connecting to other wireless connections with free (ie unsecured) connections. I have tried going to properties and ticking the "Let Windows configure my wireless network settings", but I get a dialogue box coming up telling me that not all of my changes have been made.

Any ideas? Thank you in advance.

Sukita
 

A:Solved: Changing wireless connection status from "Manually Configured" back to "Automatic"

Why don't we start with the make/model of the wireless router in use, as well as the wireless adapter or laptop brand. Also, what version and patch level of Windows do you use?

If you have XP-SP2, you can set the machine back to installation defaults using the following procedure.

TCP/IP stack repair options for use with Windows XP with SP2.

For these commands, Start, Run, CMD to open a command prompt.

Reset WINSOCK entries to installation defaults: netsh winsock reset catalog

Reset TCP/IP stack to installation defaults. netsh int ip reset reset.log
 

Read other 3 answers
RELEVANCY SCORE 84.4

When I start my laptop automatic repair appears at the bottom of the screen. This makes the screen turn blue, nothing else happens. Any ideas?

A:Laptop doesn't start - automatic repair does not work

Hi

What notebook model do you have exactly?
Did you try to recover the notebook using Recovery Medium or the HDD recovery option?

In my opinion the system recovery should be done as next because the automatic system repair does not work.

Read other 7 answers
RELEVANCY SCORE 84

This PC is an HP Desktop model Pavilion 6520f with an AMD Athlon II x4 635 2.90 Ghz processor and 12 MB of memory. The PC is from about 2010 but the 1 T hardrive, memory ,added video card (NVIDIA) and power supply were upgraded about a year and a half ago before the installation of Windows 10. I performed a clean install of Windows 7 on the newer harddrive last summer and then upgraded to Windows 10 Home edition.

A few days ago I started experiencing random BSOD errors. This was a few days after the most recent Windows 10 system update.

I initially suspected that there was a simple system volume mismatch after the update so I scheduled a CHKDSK scan on the C: drive. It froze at 10% then crashed. I tried again with the same result. At this point the computer was booting normally and could be used for a while before any freezing or crashing.

I decided to run SFC. It froze at 50% then the computer crashed. I tried this a few times as well. Always stopped at 50% and then another Blue Screen crash.

Following some online advice, I tried to run DISM command (DISM /Online /Cleanup-image /Restore

It got to 29.2%, froze , then crashed. Now when I try to boot I only get the "preparing automatic repair" and then the keyboard select screen and I am stuck.

The keyboard and mouse inputs do not work, so there is no where to go. I tried switching to a wired keyboard and mouse but no luck.

Please help. I am at a loss as to where to go from here.

Also, I have many questions. I... Read more

Read other answers
RELEVANCY SCORE 84

I hope my computer never falls into serious trouble. But if I should find myself in that position, one of the tools available to me is Windows 8's "Automatic Repair".

I've read plenty about how to start an Automatic Repair (and what to do if it gets stuck in a loop)...but I have yet to find a thorough explanation of what it does. I'm quite reluctant to hand my computer over to a process that aims to repair my computer when I don't have a good idea (or any idea) of what it's going to do to my computer.

Can someone explain or, even better, point me to where I can find out?

A:Just What Does "Automatic Repair" Do?

Hello Daddyman,

"Automatic Repair" in Windows 8 is just a renamed "Startup Repair" from previous Windows, and does the same thing. It's basically used to try and repair any Windows startup issues. For example, issues with your MBR (Master Boot Record).

Automatic Repair - Run in Windows 8

Hope this helps some,
Shawn

Read other 3 answers
RELEVANCY SCORE 84

I hope my computer never falls into serious trouble. But if I should find myself in that position, one of the tools available to me is Windows 8's "Automatic Repair".

I've read plenty about how to start an Automatic Repair (and what to do if it gets stuck in a loop)...but I have yet to find a thorough explanation of what it does. I'm quite reluctant to hand my computer over to a process that aims to repair my computer when I don't have a good idea (or any idea) of what it's going to do to my computer.

Can someone explain or, even better, point me to where I can find out?

A:Just What Does "Automatic Repair" Do?

Hello Daddyman,

"Automatic Repair" in Windows 8 is just a renamed "Startup Repair" from previous Windows, and does the same thing. It's basically used to try and repair any Windows startup issues. For example, issues with your MBR (Master Boot Record).

Automatic Repair - Run in Windows 8

Hope this helps some,
Shawn

Read other 3 answers
RELEVANCY SCORE 83.6

The "Idle-time Full System Scan" in Norton 360 v4 is bogging down my computer constantly, and there is no option to turn it off in "Automatic Tasks".

I contacted Norton and (after several attempts to find someone at Norton who could understand what I just said above and getting "hung-up" on over Norton chat. Inexcusable!!!) I was able to get a hold of a technician who told me that Norton intentionally removed this option "for security reasons, because they didn't want people turning it off".

The problem is, people will then be forced to turn it off by turning off ALL scheduled tasks (under "Settings/Scheduling/Schedule:Manual Schedule") and that is an even worse security problem than the relatively small one that would be created by turning off idle-time full system scanning.

Once the system has completed a full system scan, all files are on-access scanned anyway, so running a full system scan every 3-4 days is rather silly and extremely annoying--especially, because it will continue to try to run every time the system is idle if you cancel it.

A warning urging the user to not turn off idle-time full system scans without fully understanding the risks, and after explaining the risks, would be VERY preferable. Or at least the option to run the full system scans when the system is idle on a certain day of the month/week! The schedule for idle-time full system scans really needs to be separate from other tasks. In fact, t... Read more

Read other answers
RELEVANCY SCORE 83.6

I am using Windows 7 on my laptop and I have question about when to use "Home", "Work" and "Public" profile.

If I am logging in without setting password, and I am logging in network with "Public" profile, then will any other user, who can see my computer, be able to enter my computer and check the contents on my computer ?

I am connecting to a network and there are 6 other users connected to this network. In the set network location window, if I select the netwoek as "Home", does it mean that other 6 users will not be able to see my computer on network and if I use "Public", then all other six users will be able to see my computer on network ?

Thanks

Read other answers
RELEVANCY SCORE 82.8

I have tried a number of times to reboot and followed instructions on how to turn off the PC 3 times and a repair windows but no luck.

The PC does not want to end this loop.  Any suggestions on how to get my machine to at least get me to the blue AUTOMATIC REPAIR window.

A:Preparing Automatic Repair loop does not end and take me to any repair options

HGS Dell owner,How to resolve the Windows 10 Infinite Boot Loop ProblemWindows 10 has been seen to stick in a infinite loading Windows. To resolve this problem please follow these steps:1.Hold the FN (Function key) down while powering on the system. 2.Still holding the FN key, start tapping the Windows key to bypass the issue 3.This should bring up the login screen

Read other 1 answers
RELEVANCY SCORE 82.4

I am new here. At first a happy new year to everybody.

Yesterday I bought the boxed version of True Image 7.0 and installed it. During the installing I also made boot disks as well as as a boot cd, both in the "complete" version. After that I tried to boot from the disks and also from the cd (of course changed the bios to boot from cdrom). Both didn't work ! My computer booted and I did get the start screen from Acronis but after that it said: "Loading Acronis, please wait" , with the disks as well as with the cd. After that nothing happened anymore, even after 10 minutes.
I made a new boot cd but this time a "safe" version and that DID work. I assume however that, because there are no usb drivers etc. included, you can't use it with an external usb drive or so.
Does anyone here have the same experience or a clue to solve it ? I already emailed Acronis, but didn't get a reply yet (probably because it's New Year ?)
Thanks in advance.

Ton
 

A:"Complete" version of boot cd in True Image 7.0 doesn't work.

No idea, but this is clearly something that Acronis chould be able to sort out.
 

Read other 3 answers
RELEVANCY SCORE 82.4

Before you answer this question, I've already done the following:
1.) Download and install the latest driver for the adapter.
2.) I've already tried ipconfig /renew or release or whatever you want to call it.
3.) I've tried changing the ip address to static and rather automatic or automatic to static...Didn't do anything.

I have absolutely no idea what to do. I've tried EVERYTHING, and I mean EVERYTHING on the internet.
When I run the troubleshooter I get this message:
Please help and any would be greatly appreciated. Thanks.

A:Wireless adapter doesn't work on windows 7 "No Valid IP Configuration"

please dont double post its agaisnt our rules

Read other 1 answers
RELEVANCY SCORE 82.4

Whenever I plug in my USB device it wants to "scan and fix" but works if I just continue. On the other hand the G drive which is for my SD card gives me errors of corruption even before I took it out for the first time. Something is up with the drives and they are updated and all that. Also, with the SD card it doesn't let me delete and when I do add it is just the folder without the contents which then I can't delete. Help me fix this problem. I have a LX series Gateway computer with the pop up drive if that gives you any idea what I am dealing with.

PS: Should have bought a Mac.
 

A:USB Drives- "Scan and Fix" error and SD Card drive doesn't work.

Read other 8 answers
RELEVANCY SCORE 82.4

Sorry for posting this in the driver section, I decided to post another in the wireless section. If you want to close one, that's fine just please close the one in the driver section. Thank you.
Before you answer this question, I've already done the following:
1.) Download and install the latest driver for the adapter. I've also tried reinstalling the adapter.
2.) I've already tried ipconfig /renew or release or whatever you want to call it.
3.) I've tried changing the ip address to static and rather automatic or automatic to static...Didn't do anything.

I have absolutely no idea what to do. I've tried EVERYTHING, and I mean EVERYTHING on the internet.
When I run the troubleshooter I get this message:
Attachment 394330

Please help and any would be greatly appreciated. I need you to work with me so please help help help! Thank you guys.

A:Wireless adapter doesn't work on windows 7 "No Valid IP Configuration"

open cmd prompt type

ipconfig /all
then tracert 194.119.131.66

post results

Read other 2 answers
RELEVANCY SCORE 82.4

Hello!
I have a problem. I have adjourned the bios of the pc acer aspire M1641 and when I have restarted the pc tuneup utilities it signals me this problem:

the peripheral "Nvidia port io control driver" doesn't correctly work

Do you know as solution for this?

A:"Nvidia port io control driver" doesn't correctly work

Hi,
Did you find a solution to this problem? TuneUp Utilities report on an identical problem on my win7 system

Read other 9 answers
RELEVANCY SCORE 82.4

My dad was recently doing some work on this computer and he REALLY changed the settings in Word around. I was able to get most of them back to how I like it, except one.

When I highlight text and click "delete" to erase it or highlight it and start typing to replace it... it doesn't work. It's like some "text protector" where it doesn't delete it.

How do I fix it back to the original way? (I remember this happening once before).

-sachit
 

A:WORD: Highlight text and click "delete" doesn't work!

Come on, someone's gotta know.
 

Read other 2 answers
RELEVANCY SCORE 82.4

My Win 7x64 desktop was off for several days, with the console unplugged. Upon first start up today, I was prompted to update the AMD driver to Catalyist 12.10, which I did. It seemed to have an effect on another app that I wanted to reverse, so I ran System Restore to right before the computer was last shut down. It returned an error message, and again after a normal reboot: It read that System Restore didn't complete running. "The data is invalid (0x8007000D)." Running System Restore to later time points got the same result.

Later, I tried a cold boot into System Repair, F8 (nothing found). The System Restore error message now was as follows:

"rstrui.exe - Application error
The instruction at 0xfb30584d referenced memory at
0x00000008. The memory could not be read."

I did a google search on rstrui.exe error, but didn't find a lot and so far none of it has worked. The last system image backup before today was two weeks ago, so that's not a welcome option. Any ideas what the problem might be and how to get Sys Restore going again? Thanks,

A:System Restore doesn't work: "rstrui.exe - application error"

By chance, do you have Agnitum Outpost firewall on your machine? Other forum threads indicate this could cause problems for system restore. The recommended solution was to disable a function called Self Protection.

You could also see if there are any damaged or corrupt system files by running a system file checker scan from and elevated command prompt (option two.) If problems are found run the scan 3 times and reboot your computer after each scan.

SFC /SCANNOW Command - System File Checker

Read other 4 answers
RELEVANCY SCORE 82.4

I Have Win10 and i use RocketDock and start10 for task-bar transparency, but for some reason the "Minimize windows to the Dock" does not work at all for me ! .... will be amazing to have a proper fix ! thank in advance!

Read other answers
RELEVANCY SCORE 82.4

Hi all,

I noticed a really annoying issue on my machine.

When installing various software, when it asks me if I want to customise location, when I click on the "browse" button, it either doesn't do anything or in some cases it will open "Browser For Folder" window, but it will only show my Desktop>Usename folder, nothing else.

Software like K-Lite Codec pack will work fine as in I can change the installation location, but other software wont work :/

I do have mapped network drives if it makes any difference.

Any help would be much appreciated!

Read other answers
RELEVANCY SCORE 82.4

Howdy, folks.
I right click a link (.lnk), click Properties, then click "Find Target" and instead of folder with the target opening an Open With box opens. It has several programs suggested, but not explorer.exe. I have to browse for explorer.exe.

How do I fix this problem?
 

A:"Find Target" in link properties doesn''t work

Read other 8 answers
RELEVANCY SCORE 82.4

I'm running Windows 7 Ultimate (Build 7000) on an lenovo pc (Intel Pentium 4 - 2.8GHz, 2.00 GB RAM). my pc's actual graphics card is "Intel 82865G Graphics Controller" but windows 7 loads it as "standard VGA graphics card" which gives me a very very bad video quality but computer works great. HOWEVER,when i update video graphics back to my "Intel 82865G Graphics Controller" & play any video, the video quality is excellent & direct 3d & hardware acceleration starts working contrary to "standard VGA graphics card" but gives major computer operation problems. For e.g., As soon as i resize my VLC interface or run any other media players (like powerdvd or windows media players etc), the computer either gets stuck/hung or it shows a blue screen message saying "disable bios memory such as caching or shadowing" OR "page_fault_in_nonpaged_area" & lots of other explorer based problems.i tried changing various 3d settings in opengl as well, but in vain.


CAN YOU PLEASE HELP ME WITH THIS??

ITS A MAJOR BUG in WINDOWS 7.

I MEAN U CANNOT ASK SOMEONE TO UPGRADE his OPERATING SYSTEM AT THE EXPENSE OF CHANGING HIS HARDWARES.

THANK YOU.

A:"Intel 82865G Graphics Controller" doesn't work ??

It is a driver issue. I suggest that you download the driver from HP website, remove the existed driver and install the new downloaded driver.
HP Compaq dc5000 Small Form Factor PC - Download drivers and software - HP Business Support Center

(note; if u found useful dont forget to ad me rep)

Read other 9 answers
RELEVANCY SCORE 82.4

Whenever I try to open a file with a program such as Winamp, the programs now "arranges the icons" in some funky random arrangement instead of arranging them by name (or by type, or modified) or whichever order I had preset. When I tell it to "arrange icons by" name or whatever other options, it arranges them....until I try to open something else. Then it's back to the funky random arrangement.

This only happens when trying to access a file from a different program. When I access the folder through Windows, it remembers the arrangement perfectly. Any clue as to what's going on here?

Any help is greatly appreciated!
 

A:"Arrange Icons By" option doesn't work anymore!

Read other 12 answers
RELEVANCY SCORE 82.4

We've having problems getting the "Out of the Office" function to work. Well, it works just fine internally, but if someone outside our company sends any of our users that has "out of the office" function enabled an email he/she won't recieve the OOTO message.. It works just fine internally (ie I send a mail to another colleague that is away).

Could it be some setting on the Exchange server I've not discovered/I've overlooked?
 

A:Outlook 2000 and "Out of the Office" doesn't work externaly

Solved! My mistake. The "Allow out of office responses" wasn't turned on for some reason..
 

Read other 1 answers
RELEVANCY SCORE 82.4

I've got a weird problem here to report. I'm on a Lenovo N200 laptop running Windows 7 x64. Around half the time, the computer will boot up with the trackpad not responding. During times when this happens, I can look into the device manager and see a "code 10" ("device cannot start") for the trackpad. Restarting the computer fixes the problem.

I've had the problem once or twice over the last few years, but just a few weeks ago, it started happening very regularly (+/- 50% of all startup attempts). I can't recall making any notable changes to the system lately that could cause something like this. When the problem first started, it also affected the display adapter (Windows would start with an extremely low resolution and the graphic card would show a similar fault in the device manager, in addition to the trackpad problem described here), but this has since stopped.

I have tried updating the driver for the trackpad to a newer version, but the problem persists.

Hardware faults were considered, but I was able to successfully boot the computer from a WinPE CD five times in a row with no issues, so it would seem like this is less likely to be a hardware bug.

Any ideas as to where to go from here? I don't want to have to reinstall an otherwise clean and functional operating system for something this trivial.

A:Trackpad doesn't work, gives error "code 10" on every other boot

Hi, try using this to check the temps HWMONITOR | Softwares | CPUID
Temps can play havoc with laptops.
Cleaning the fan and air vents with a can of compressed air might clear away ant dust or debris, which could cause temps to rise.

Read other 1 answers
RELEVANCY SCORE 82.4

Hello
I have an HP pavillion desktop (s5360f) with Atheros 802.11 a/b/g/n Dualband Wireless Module and D-Link router DIR-615. My numerous Laptops and iPhons / iPads work fine, but this desktop which is further away from the router (in another room, about 20 meters) only shows 1-2 bars of wifi. First I bought a big additional D-Link antenna (7Ghz) but it didn't really help - sometimes connction shows 3 bars. I was told this antenna should help a lot. Then I checked with my router settings and saw that the HP uses "g" connection when everything else uses "n". I even set it to only use "n" but still it shows the HP using "g". I updated the driver (Atheros 9.2.0.113 for AR5B91), but it didn't help. I have "n" enabled in Atheros in Device manager.
Now I'm lost and can't think of anything else that can be a problem and / or how to fix it... I don't have any thick walls between the router and the HP, my iPhone seems to work in this room just fine...
Please help!
THANK YOU!

A:Atheros Wifi adapter doesn't work with "n" router

Out of curoisity, are you suffering any symptoms of lack of signal qualities (glitchy video/slow connectivity)?

And what speed does the HP Desktop show it being connected at?

Read other 3 answers
RELEVANCY SCORE 82.4

Hi,

I had an issue with the general user folder name, which was shown as "Alex_000".
Although this was a cosmetic issue only, I wanted to change this to "Alex".
I successfully managed this by changing about 50 entries in the registry (via regedit).

So fine so good.



Now I found out that there are still some leftovers with "Alex_000" in the Windows system, although I have tried to find every bit and peace, where possible:


When I try to open "Add or Remove Programs" in the Metro surface, I get an error message:


Windows cannot find

'C:\Users\alex_000...\Classic_{a lot of weird numbers and chars}.settingscontent-ms'.
Make sure you typed the name correctly, and then try again.



From another forum topic, i also tried this command via Metro and RUN to see, if the Remove service has a general problem:

C:\WINDOWS\System32\rundll32.exe C:\Windows\System32\shell32.dll,Control_RunDLL "C:\Windows\System32\appwiz.cpl",Add or Remove Programs
--> With this, i can open the Remove service without a problem.


Somewhere in the system, there must still be the Alex_000 info hidden.


How can i find this? (Tried the registry, tried a simple search on C: disc, but without success)

How can I solve this?


Thanks a lot!

Alex

A:"Add or Remove Programs" doesn┤t work anymore (in Metro)

The obvious answer is to change it all back to Alex_000. Renaming a system folder doesn't usually go well.

Read other 5 answers
RELEVANCY SCORE 82.4

Installed Publisher 2003 on new windows 7 computer and noticed that the "fill" command would only fill in white. Went to the "Paint" program that came installed on the computer and the same thing was true. Should I upgrade to Publisher 2007? If "Paint" doesn't work, why would an upgrade to Publisher 2007 work?

A:Paint, Publisher "fill" command doesn't work

Hello Vrnuta, welcome to the Seven Forums.

By default the fill color (color 2) in both Paint and Publisher is white. Are you sure you remembered to change it to color you want to use?

Kari

Read other 1 answers