Over 1 million tech questions and answers.

hp omnibook xe3 continuous rebbot

Q: hp omnibook xe3 continuous rebbot

a friend gave me his laptop. when i start it the hp invent logo comes up and then it goes to the screen where you can start it in safe mode, normal....etc. i have tried all these options and have even hit f10 and tried all those options. i have also tried booting with the xp disc and that does not work either, just seems like it is not even reading the disc. nothing is working. is the computer shot or is it fixable.

RELEVANCY SCORE 200
Preferred Solution: hp omnibook xe3 continuous rebbot

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: hp omnibook xe3 continuous rebbot

Hello, and Welcome
 
Press F8 and select "Disable Automatic Restart on System Error" Does it throw a blue screen stop code"?
 
http://pcsupport.about.com/od/fixtheproblem/ss/disable-auto-restart-vista_2.htm

Read other 21 answers
RELEVANCY SCORE 48.4

system will not boot up after turning on, goes to blue HP screen with three choices, esc (escape), enter setup, and system recovery. escape and system setup will continue on to next screen but does not fix the issue. eventually a black screen appears with white writing stating that a hardware or software issue has cause a shutdown and that this was done to protect your files it goes on to give you four choices to boot the system. safe mode, safe mode with networking, safe mode ????? and open windows normally. after choosing any of the options, the windows XP screen pops up for 5-7 seconds as if it is rebooting and then the process starts over.

A:rebbot issue

Have you recently installed any software? If you have then your Anti-Virus software might have a conflict especially if you have Norton, McAfee and TalkTalk Security center.

If you can boot into safemode remove any new software and anything that might have effected it.


Or.

Do you still have your XP disc? Let me know if you do and I'll offer more help.

Read other 2 answers
RELEVANCY SCORE 48

My laptop (Hp Pavilion dv5- 1015 tx) has preinstalled vista with sata harddisk. I want to install xp to an external USB Harddisk, which is IDE. So I slipstreamed xp adding also the sata driver. I can boot it with xp boot cd. It copies the files for installation to the external harddisk. but on reboot i get error message because it does not detect the harddisk. Installation stops automatically, saying to prevent damage to the computer. I tried sever times. The same thing happens always. Kindly help me.

A:Not detecting IDE usb harddisk on rebbot

XP is not meant to be installed on USB drives. There's a moment during startup when the usb controller is reinitialized, this is what's preventing the installation to continue.

Here's a workaround that involves editing usbstor.inf and other system files on the XP CD : http://www.ngine.de/index.jsp?pageid=4176. Can't tell you if it'll work as I've never tried it.

Read other 3 answers
RELEVANCY SCORE 48

using samsung chronus 7 laptop
windows 8.1 64 bit O/S.

Problem
On start up get the samsung screen then a blue screen with a sad face saying pc needs to restart. Then goes in a continus reboot.

tried using the w8 recovery cd. But get on the screen press any key to boot from cd. but press any key has no effect and goes back into loop as before.

press f2 to get to bios reset defaults, no luck either, tried f10 just get boot up order, unable to find what keys boots into recovery mode, f8 does nothing no safemode.

any one offer any help or advice please windows was pre installed.

A:stuck in rebbot loop need help

using samsung chronus 7 laptop
windows 8.1 64 bit O/S.



Try booting from a Windows 8.1 disk (DVD/USB) not a Windows 8.

Read other 7 answers
RELEVANCY SCORE 47.6

Hi all.

I have searched on here re this problem but all the threads I have seen talk about a drive going offline which isn't the case here.

Firstly its not my machine, I'm helping an old friend so there may bee delays on certain questions.

He has a DELL XPS machine, an i7 newer model running 8.1, he's got a main internal HD as C: and a permanently added USB drive with 3 partitions ad D: E: and F: but on reboot the F: partition suddenly goes up a letter to G:, the other two stay the same.

Apparently its been fine until recently when this started happening, I made sure the used Disk Management to change the letter back but on reboot its back to G:

He has no other devices attached and any other USB drives either have a selected letter near the end of the alphabet or are not assigned a set letter but none are attached when the machine boots. It sounds like the F: is being reserved by something, possibly registry wise but I don't have the machine in front of me to check and I would rather its me using regedit and he's got slippery fingers due to arthritis and is prone to over clicking and wrong key presses.

Any suggestions as to where to check or what to check, I've done as much as I can via Skype but at a loss as to why its only doing it to one partition and always the same one, also did a dischk and the partiton is ok.

Any idea's wise folks?

A:Windows 8.1 changes a certain partition letter on rebbot.

Seems he was using some sort of safe eject USB software where you could reserve a drive letter?

Seems ok now...So far..

Read other 2 answers
RELEVANCY SCORE 46.8

Hello

I am experiencing the most annoying issue with my Machine.

Even after a clean install.

From a cold boot, I power my machine up.

From the moment the OS loads and I can see the desktop, within 1 - 2 minutes my screen goes black. The numlock on the keyboard freezes and I cannot recover the machine. I hold the power button down for a few seconds and machine powers down.

I then power up the machine and it works fine till a shutdown at night and try reboot it the next day.

And this happens every time I boot the machine after it was off for the night.

I have checked the event log and all I see is that the machine did not shutdown properly.

If I look at the LED on the MB it goes through a bunch of post codes, when I am at the desktop it stays on code 13.

After it crashes and I reboot, once at the desktop the LED stays on code 16, and will work fine till I shutdown.

Where can I start to try resolve this?

Thanks

Specs
OS: Windows 7 ultimate retail (Fully patched)
Motherboard: Biostar T-Power i45 v5.1 (Latest Bios)
Ram: OCZ Reaper HPC Edition 8gb
CPU: Intel Q9550 Core 2 Quad
Cooler: Thermalright Ultra 120 eXtreme
GPU: Asus ATI Radeon EAH 4870x2 (Latest ATI drivers but tried ASUS drvers as well)
PSU: Zalman 1000w
AV: MS security essentials

A:BSOD WIN 7 64Bit after 2min, after rebbot works 100%

Hey.

Go into the bios and set the vdimm to 2.1v for the memory voltage. Also set the timings manually at 5-5-5-15(CAS-TRCD-TRP-TRAS)

Let us know how it goes.

If it still continues to exhibit the problem, go to C:\Windows\Minidump and copy the files in there to any other folder. Rar or zip them and attach the compressed file to a new post using the paperclip above where you type.

Read other 3 answers
RELEVANCY SCORE 46.8

When i started my laptop..the system went to startup repair mode..the startup repair mode did not worked n i went to ''restore to factory setting ''.Now the main problem arised.The factory setting later asked to reboot the system .the system failed to reboot.it gave the msg as ''bootMGR file '' missing.I was told by a local tech to use operating cd to repair the laptop.Now wat i saw the hard disk partion failed to That is before it was C:drive 50 gb & D: drive 450 gb.Now it was C:drive 498 gb & D: drive 1.98 gb,
Which means i have lost all my important data which was in my hard disk .Is there no way for the data recovery.
How come ''restore to factory setting failed ''?
 

A:windows 8 factory setting failed cannot rebbot

see if this sees anything

http://download.cnet.com/DiskDigger/3000-2248_4-10908894.html

see what you can save then run the hard drive makers diagnostic on the drive
 

Read other 3 answers
RELEVANCY SCORE 46.4

After I log in action center alerts me that Windows Firewall is turned off and that I should turn it on.
 
It does turn on with no problems but after I reboot, it happens again.
 
Used to be a problem along with Windows Update not remembering my settings but that problem seemed to have been fixed. Thread related: http://answers.microsoft.com/en-us/windows/forum/windows_7-system/windows-7-firewall-and-update-will-not-remember/330abb9a-90d7-40cc-8c10-53584ece9047?tm=1307165383153&page=1#footer
How do fix this and enable Windows Firewall to run automatically after reboot?

A:Windows Firewall Service does not start automatically after rebbot

Hi,

 

I would like confirm the following with you before troubleshooting, these information would useful to help us to narrow down the root cause of this problem.

1.      
When did the problem occured?

2.      
Did you install any third-party software recently?


3.      
Have you scan the virus on your computer?

 

Since you can start Windows Firewall service manually, we can judge that the service is properly and wasn’t disabled. I suggest that you may perform a Clean
Boot to ensure whether is problem is caused by a third-party software.

 

http://support.microsoft.com/kb/929135

 

Note: Clean Boot is a step of troubleshooting, we can go back to normal by running MSCONIFG.

 

If the issue persists, I recommend that you may enable the Service Audit, then check the log.

 

Please take the following steps to enable Audit Policy:

 

1.      
Click Start button, type gpedit.msc in Search Bar. Press Enter.

2.      
Move to Local Computer Policy-> Computer Configuration -> Windows Settings -> Security Settings -> Local Policies ->Audit Policy.

3.      
Find the item ---“ Audit directory service access”, double click the item.

4.      
Check &ldqu... Read more

Read other 4 answers
RELEVANCY SCORE 46.4

Hi guys, Beforehand forgive my English not my first language and thanks for help and assistance.

This is my new build and this is what it's happening:

I set to Boot into DVD/CD
Place my Microsoft Windows 7x 64 ultimate Disc in tray.
Black screen appears with a loading bar saying " Loading files" .
Another screen appears with "blue sky" and the dove and there is were all computer Froze (no mouse or keyboard) for about 3 minutes!
And then the computer reboot itself !!

This are my specs:
Gigabyte GA-P67A-UD4-B3
Intel Corei7 2600K 3.4GHz 8MB.
Corsair Vengance 8GB 1600MHz
eVGa Ge-Force GTX560TiFPB 1GB.
Antec EarthWatts EA750W ATX12V.
HD Maxtor model 6L200S0 diamond max.SATA 200GB
HD Western Digital WD500AAKS 500GB caviar blue.
Asus 24x DVDRW SATA black.

I have set in Bios the HD's as IDE's......but I'm missing something and don't know now what else to do, feel pretty baffled.
I been searching in the forums .but still haven't found something that point me in the right direction for my case.

Note:
I use to have the O.S. installed in the HD WD500AAKS the Windows7 Ultimate 64 bit .
So I use gparted-live-0.8.1.3 to wipe both HD's partitions and formatted as NTFS both.
But still Windows7x64 Install don't go

Thanks for help.

Toti
 

A:Solved: Windows 7x64 Install freezes and pc rebbot itself.

Read other 16 answers
RELEVANCY SCORE 42.4

Hey Everybody.

I have an HP OMNIBOOK 4150B. I installed Win XP pro and it ran great. Fixed a bunch of things actually. I lost some minor functionality but that wasn't a big deal. The problem was that when I booted up the computer without it being plugged in(AC), it would freeze up after 30 seconds or so. So basically my laptop became a very portable desktop.

I reinstalled the recovery CD (win 98) and it solved the problem. However, I would really like to run XP with my OMNIBOOK....there must be a way to do it.

I was just wondering if anyone else was experiencing this problem or if anyone knew how to fix it.

Anyone know where to get all the drivers?
 

Read other answers
RELEVANCY SCORE 42

Hi,

I'm Upagainstthewal (one L). Huge problem. I'm locked out of my HP Omnibook 6000 by a BIOS Password that I didn't even set. I have no clue on what it is or how to retrieve it? Is there a bypass or master password for this. I know that the provider is Phoenix. Can anyone lend a hand in assisting me with this issue?
 

A:HP Omnibook locked out

Hi there,

Google 'CMOS password reset' take your pick. Have used one of these in the past, can't remember which, find one that suits. Often resets to no password...

hi from SA

PS failing that I have heard that taking the bios battery out for a few hours can reset to no password. either way double check whilst googling... plenty of similar events... good luck
 

Read other 4 answers
RELEVANCY SCORE 42

I have a HP omnibook Xe2 laptop, yes it is old but it still has some kick to it. I originally replaced the fan because it became too noisy and made a pulsating sound after the laptop had been on enough time for the fan to kick on for a cooling cycle. I now have replaced the fan 3 times. In the beginning, the replacement fans work great, then they begin to make the same pulsating loud vibrating noise. The power cord of the fan is not a variable, it is out of the way. Any help would be great...

I had thought that maybe there is an electrical/power problem with the cord supplying the fan with power. Maybe there is too much power being sent to the fan and is frying the fan making it sound all loud and pulsate. But who knows...
 

A:fan problem on HP omnibook

What fans are you using? Are they the correct voltage? Are they good fans, i.e. ball bearing?
 

Read other 1 answers
RELEVANCY SCORE 42

I have an older HP OmniBook 2000CT with Windows 98 build 4.10.1998 with a Pentium I 133Mhz MMX processor and 32 Mb of RAM. When I insert a CD into the swappable Toshiba XM-2402B CD-ROM drive ("HP F1347A 10x CD-ROM Drive Module") nothing happens. The drive has power and reads the disk, and displays a list of files in windows explorer/my computer and I can browse through the folders. However, when I try to open/run a file, i cant. It either says "handle invalid" or a like message. If you have any idea of how to fix this or where to get a new drive, please tell me.
 

A:OmniBook CD-ROM Problem

What kind of files are you trying to run?

Can you open TXT files (like README.TXT)?

------------------
Get free stuff and help out a poor computer tech:
LarryCore begs for money
 

Read other 1 answers
RELEVANCY SCORE 42

Hello! I still have my Omnibook XE3 GC, and i am currently using it for my retro games! I would also like to use it  for some simple MS Office tasks, by dual booting WinXp(Currently using Win98SE). So i thought that an upgrade is needed to make my old dinosaur a bit faster! I already got my self two 256mb dimms of ram, and i want to also upgrade my CPU. It currently has a Pentium III 850Mhz. Does anyone know if the board is going to support any faster Pentium III's?They are pretty cheap. I found a tualatin PIII 1.067Ghz on ebay for about 3Euros.Thanks in advance!

A:Omnibook XE3 Upgrade?

The Manuals for that classic machine were long ago retired here. 512 megs of RAM is going to be light on XP. I do seem to recall that the XE3/Pavilion N5400 could accept up to a PIII Mobile up to about 1.3 ghz. 

Read other 2 answers
RELEVANCY SCORE 42

I have an Hp Omnibook XE2 with only 5 GB of HDD and 64 Mb of RAM, Win 98 SE operating system. On my desktop I use Win XP Pro, and would like to move on to Win XP on my notebook too, preferably without buying a new notebook.

I intend to install maximum RAM (512 Mb) and a Hitachi Travelstar 7K60 HDD. Can anyone advise me if it is worth the effort to upgrade. I would only use Ms Office 2003 applications.
 

A:Upgrading Hp Omnibook XE2

I've run XP on sub 1Ghz computers before and although it is more stable, it will take a big preformance hit. Just before you dig into it, consider the cost. You can buy a new laptop from Wally World for under $500 when they are overstocked.
 

Read other 2 answers
RELEVANCY SCORE 42

I have a Pavilion laptop that was sent in to HP to replace the motherboard. Now the Pavilion thinks it is an Omnibook, so the original Application & Recovery CD's will not work.

Has anyone experienced this?
Is there a way to force the computer to accept the original software? Or do I now need Ominbook sotware & how do I know for which model?

BTW, HP would not make good on it, even though they admitted they installed the wrong motherboard while the laptop was still under warranty. Their reply was that "it happens" and then they wouldn't discuss it any further.

I also have always had a problem with this laptop. When I boot it up, the screen will blank out every few minutes. I use the function key & F12 to switch it from the LCD to an external monitor & back again. That brings my screen back up, but it sometimes happens every few seconds and is a real PITA. Does anyone have an idea on the cause of this problem?

Thanks for any help you can provide!

Ange
 

A:Pavilion now an Omnibook

I don't think that I would accept this answer from HP. At the very least they should send you the right recovery discs. Keep asking for a supervisor until you find someone who agrees that it is their job to help you!
 

Read other 1 answers
RELEVANCY SCORE 42

The following concerns an HP Omnibook XE3 GF Notebook, running Windows
XP Pro.

Occasionally the screen blanks (completely black) as though the
machine were in standby mode. This may happen soon after booting or
after several hour's use. It may happen more than once on one day, or
maybe it doesn't happen for a couple of weeks.

After power-switch off, or hardware-reset, to shut down the machine,
the standby button re-boots it, but the display is _not_ restored.

However, the display _can_ be restored by: power-switch off, unplug
the power cord, remove the battery, wait a couple of minutes, replace
battery and power cord, press standby button to re-boot.

Having removed/replaced the battery, following a screen blank, Windows
insists on performing a consistency check on the FAT32 hard drive, at
next boot. The last time this happened two errors were found:

Windows will now check the disk.
Volume Serial Number is 2C77-3ED5
\WINDOWS\Prefetch\LOGONUI.EXE-0AF22957.pf first allocation unit is
not valid. The entry will be truncated.
\WINDOWS\Prefetch\NTOSBOOT-B00DFAAD.pf first allocation unit is
not valid. The entry will be truncated.
Convert lost chains to files (Y/N)? Yes
336 KB in 2 recovered files.
Windows has made corrections to the file system.

If the screen did not blank, removing/replacing the battery doesn't
cause Windows to perform the hard drive check, at next boot.

I should be grateful for advice as to

why the screen blanks,

why Windows performs a consi... Read more

A:Omnibook display, again

Read other 8 answers
RELEVANCY SCORE 42

I'm working on an old HP omnibook xe2 that had been stored for a couple years. CMOS battery was dead, so no operating system. Have changed battery. Laptop will power up and checks drives, but will not boot from either floppy or CD-rom drive. Tried to access BIOS setup menu-computer says"entering setup" then stalls. Where do I go from here?
 

A:HP omnibook problem

Read other 7 answers
RELEVANCY SCORE 42

I am trying to upgrade my omnibook 4100 notebook from the original 4 Gb to a 10 Gb .i have done an image onto the 10 Gb , but it will not boot . any ideas ?
 

A:Omnibook 4100 HDD

Obviously the imaging did not work
You will need to Repair your Windows

Microsoft's Windows XP Professional Repair Install step by step
http://www.windowsxpprofessional.windowsreinstall.com/installxpcdrepair/part3.htm

Microsoft's Windows XP Home Repair Install step by step
http://www.windowsxphome.windowsreinstall.com/installxpcdrepair/part3.htm

Vista Repair:
http://www.windowsreinstall.com/winvista/index.htm
http://vistahomepremium.windowsreinstall.com/repairstartup/repairstartup.htm
 

Read other 5 answers
RELEVANCY SCORE 42

i have an hp omnibook 6000, i updated the bios to 1.83 now i'm trying to install winxp,the problem is after booting from the xp cd, and after winxp loads all the drivers,when it gets to the blue screen window setup , the system hangs . also if i booted with win98 or me with cd-rom support also the system hangs
 

Read other answers
RELEVANCY SCORE 42

I have an HP OmniBook XE3 that has a BIOS password issue.

Windows Xp Home
Intel Celeron 1.2 GHz
256MB Ram

I wanted to go into my BIOS to disable my notebooks CD rom. I hit the F2 key and when it loads it asks for a password. I have tried to call the guy I bought it from to see if he knows what the password was and he tells me that he forgot what it was.

Does anyone know how to reset the bios password for an HP OmniBook Laptop? I have tried to enter a few of the “backdoor” password for the Phoenix BIOS. I have not found any useful information on what I can do to fix this issue and that is why I came here.

Anyone have any ideas?
 

Read other answers
RELEVANCY SCORE 42

Hi,

I have a Hp Omnibook 900 Laptop which has been formatted and windows xp pro installed.

the user would like to use the usb port i.e the usb mouse etc.

I have checked the device manager but cant find
Universal Serial Bus controllers.

I have checked the Hp drivers website but cant find any drivers for win xp. what should i do?

thanks
 

A:usb drivers for hp omnibook 900

First off, are they enabled in the BIOS?

That's a pretty old machine, HP may not offer XP drivers for it. Perhaps you'd be better off running the version of Windows it came with.
 

Read other 2 answers
RELEVANCY SCORE 41.6

The following concerns an HP Omnibook XE3 GF Notebook, running Windows XP Pro.

When the CD/DVD drive is _not_ in use, its status-light flashes at intervals of approximately 1 second, throughout the time that the machine is powered-on.

The status-light in question is mounted on the switchboard PCA, immediatedly behind the keyboard, not the one mounted on the drawer of the drive, which remains unlit.

It seems that the OS is continuously polling the CD/DVD drive. Is this normal? Is it possible to turn it off?

Tony
 

A:hp omnibook cd/dvd status-light

Does this only happen when there's a disc in the drive?
 

Read other 2 answers
RELEVANCY SCORE 41.6

I greet, I am user HP XE3 GC and looking for of drivers to sound cards as well as network cards under windows xp.
I greet warmly
Robert Kosar
 

A:HP Omnibook XE3 GC driver windows xp

Read other 7 answers
RELEVANCY SCORE 41.6

I need to get the cover off to repair/replace the power jack. Are there hidden screws or other tricks?
 

A:hp omnibook XE2 cover removal

Bobby,

Welcome to the Forum.

This would be worth $10:

http://computerdoc.homestead.com/DRSILaptopManuals.html

and this might work out for free:

http://askanowner.com/qa/view.asp?sid=1&qid=9788

I've had my HP ZT1170 apart a couple of times. Apparently for the same reason as you...broken power plug.

The first time it was split and loose from the board but still intact electrically. I repaired it with JB Weld epoxy.

The next time the solder joint broke. I repaired it with a needle point low wattage iron. I would call it a poor design for a potentially stressed connection...I use it on my Lap not on a desk.

Each time it was like the first...where is that hidden screw? Their engineers have a warped sense of humor.

Also, I noted that the machine was available used for about $700. The MOBO replacement part is $470. Capitalism Lives!!!
 

Read other 1 answers
RELEVANCY SCORE 41.6

Hey guys,

I have an old school HP OmbiBook XE3 laptop. My dad recently upped the RAM and was reinstalling windows and by mistake he took out the CD in the middle of the installation. Now the computer wont boot up, even using the system recovery CDs. Also when I open the laptop, some weird characters come up (picture attached).

So any ideas as to what I can do to fix this?

Thanks!

A:HP omnibook XE3 wont boot

Now the computer wont boot up, even using the system recovery CDs. Also when I open the laptop, some weird characters come up (picture attached).If the laptop will not boot, how does the monitor present the info posted?What happens when you try to boot from the recovery disk(s)? Any error messages? Blinking cursors? Restarts?

Read other 4 answers
RELEVANCY SCORE 41.6

Hi all

My friend lend me his laptop, and I played with bios, and after reboot laptop request password. I was trying possible password what I set up. But I do not have correct password. My model is HP omnibook900 and HASHCODE is 01224

Thanks
 

A:/lent laptop/ Omnibook 900 please help

Don't ever play with the bios again :rolleyes: especially on someone else's computer
 

Read other 1 answers
RELEVANCY SCORE 41.6

My laptop

About a month ago I got my first laptop. It is an HP OmniBook 4150 (128 MB of RAM, 300 MHz, 6 gig hard drive). It's by far not the most powerful or recent laptop available <grin> but it gets the job done. It's run Windows NT 4.0 (Workstation), Windows 2000, Windows ME, and Windows XP all on it successfully without any problems. Last night I formatted and did a fresh install of Windows XP Home Edition (I have Pro also but chose to use Home on it). In the past I had WinXP Pro on it and it worked fine also. I recently used the laptop to do my Windows 9x/ME Tweak Guide ( http://members.fortunecity.com/computingx ). Windows XP Home Edition is on it now as I said, and running quite well. It is slightly sluggish at times, but not that bad. It runs very stable and reliably. I am impressed despite the slight performance barriers, but it isn't bothersome. It runs everything I throw at it just fine, even some games I've tried. It's really nice to be able to have the portability if I want/need it. And besides, laptops are just sexy, somehow. :grinthumb
 

A:My Laptop (HP OmniBook 4150)

If you want to get rid of that sluggishness that you speak of, put another 128mb of memory in it. WinXP requires 128mb and recommends 256mb. That will help out alot.
 

Read other 7 answers
RELEVANCY SCORE 41.6

I ran MalwareByte and it detected no virus even though I"m getting blocked on some sites. I have HP Omnibook 900 with a hard drive only, no A or CD drive. I've downloaded KillDisk to reformat hard drive, it needs to run in pure Dos mode. My USB drive is B (with KillDisk installed), and my hard drive is drive C. I've edited msconfig to run in safe mode. When I run KillDisk in command prompt, it prompt that I have to close Windows. What am I missing?

A:KillDisk reformat HP Omnibook 900

Safe Mode is still Windows...you need to boot into DOS.

Any particular site or sites that you are being blocked from? Have you tried different browsers? Have you disabled any software firewalls?

Read other 12 answers
RELEVANCY SCORE 41.6

Hi everyone,

I was trying to delete my HP Omnibook XE3 BIOS password by changing it to blank (using<ENTER>), and I was locked. I tried the old password, <ENTER> and all the keys around <ENTER> key, but no success.

I am not expert with jumper and BIOS battery manipulation. The laptop is old and it does not worth spending money to fix it.

Would any one kindly help me with this problem? I found in this forum that some guys can help with a password that can unlock it. I got the hash code and it is 13053.

Please help me if you can.

Thanks in advance!
 

Read other answers
RELEVANCY SCORE 41.6

I have recently purchased an external CD burner drive and wish to connect it to a P3 700/256 mb/USB with an internal floppy.. the drive came with drive cds but no floppy to install driver.. can this be done
 

A:HP Omnibook/External CD Burner

Read other 16 answers
RELEVANCY SCORE 41.6

I have a dump here from the 24c16 for my hp omnibook xe3

can any 1 decode the password for me. I have tried ibm pass 2.1 with no luck.

Thanks
 

A:HP omnibook xe3 bios password help

remove baterry cmos batery and hdd wait 3,5m and boot only whit ac adapter
 

Read other answers
RELEVANCY SCORE 41.6

I need to enter the bios of an old omnibook XE3.The hash code is 06653

A:HP Omnibook XE3 hash code

Hi, Enter:     dack                    or              wfhwfkl Regards, DP-K

Read other 3 answers
RELEVANCY SCORE 41.6

I have a problem I really need help with.

I reloaded an Omnibook 800CT with the original restore disk. Everything
setup just fine.

When I installed a 3Com XJ4336 Modem, (voice) I got an extra 'other device'
in device manager. This 'other device' is a PCCard Services.

How do I get rid of this? Reinstalling the PCMCIA drivers does not help.

Any Suggestions?

 

Read other answers
RELEVANCY SCORE 41.6

Hello,
a friend of mine give me an LAPTOP HP OMNIBOOK 900 but the hard drive was Out.I bought a new one and install windows XP on.But i can't use it because there's a BIOS Password that i don'tKnoW.
How can i reset this Password (On this computer, there is no CD, no Diskette).

Can anyone help me ? thanks a lot
 

A:Bios Password Hp Omnibook 900

I Found EEPROM 28SF040 120-4C-NH, I think password is store inside.Can you tell me how reset ?
 

Read other 3 answers
RELEVANCY SCORE 41.2

Hitting delete during boot up does not work like most computers.
 

A:How do I get into my Laptop bios? HP OMNIBOOK 4100

Also try 'Tab' or 'Esc'.
 

Read other 2 answers
RELEVANCY SCORE 41.2

Need omnibook 6000 bios password.....the hash code is 03312.
I been searching all over the web.

Thanks to all out there!
 

A:Need HP omnibook 6000 bios password

wrong forum.
 

Read other 1 answers
RELEVANCY SCORE 41.2

Hello everyone!I got this oldie HP OMNIBOOK 6000 from the friend of mine, yet I got 2.5 inch IDE notebook drive in addition.Now I want to replace FDD in 6000's module bay with F2018B caddy  module (http://www.hp.com/ecomcat/hpcatalog/specs/F2018B.htm) to insert that 2.5 inch HDD as 2nd drive. Please tell me where I can get F2018B caddy itself (w/o HDD inside, of course) - and buy it ?Only caddy is needed (IDE port inside, not SATA), again. Thanks in advance!  

Read other answers
RELEVANCY SCORE 41.2

Hi All,

I have an HP OmniBook XE3 with 256MB of ram a 1GHz Celeron Processor running Windows Xp Home.

Everything was working ok on it until today.

This laptop will not allow me to:

Boot using a floppy disc
Boot into safe mode.
Boot from CD.
Change the boot order.
Enter BIOS Set-Up

It has been working fine until today. When the system begins to boot I can hear the CD start to spin then quit. I have tried to change the boot order by hitting ESC button with no luck it looks like it is showing POST test with “ATA CDmrom SCRm2t2’’’’’’’) as the last item in the list. When I hit F2 to enter the BIOS setup all I see is “Entering SETUP….” And it never loads past that.

Any ideas on what to do?
 

A:Solved: Ho OmniBook Boot Issues

Read other 9 answers
RELEVANCY SCORE 41.2
RELEVANCY SCORE 41.2

I tried swapping in a known-good mouse and this failed to resolve the problem. I entered BIOS setup and ensured that both the touchpad and PS2 mouse were configured to work. I uninstalled the mouse drivers and rebooted so Windows2000 would detect and install the mouse. After Windows had installed the Mouse it functioned fine however when logged out and then back in the mouse failed to work again. I flashed the BIOS on the laptop with the latest version (downloaded from HPs Omnibook support site). I installed Windows 2000 SP2. I then removed the mouse drivers again and rebooted. As of this time the issue remains unresolved. The PS2 mouse will not function. The laptop is otherwise funtional, however, and the user can navigate using the touchpad, keyboard, and pointing stick. Incidentally....Event viewer shows no errors....

Any thoughts on how to fix this?
 

A:Omnibook 6000 PS2 Mouse nonfunctional

Are you using a Synaptec's (sp?) Touchpad (which my lappy has)? If so, you should be able to go into control panel - mouse, and there should be some settings (over and above the default windows mouse settings if you have the synaptec drivers) to have the ps2 mouse enabled as well as the touchpad. You may also want to check out device manager and ensure that there's no conflicts between user input devices.

If you aren't using a Synaptec touchpad.. then ugh.. you may need to contact your laptop manufacturer for assistance.
 

Read other 1 answers
RELEVANCY SCORE 41.2

Hey everyone, I have a friend with a hp omnibook 7100 that was handed down by some far off relative. It's a p2 266 mhz, 256 mb sdram, I don't know the mb specs, anyway it was running win xp fine and then one day it just booted to advanced startup options and hangs there, never responding to any of the options. Since he didn't have much on his hd I decided to do a clean install from the cdrom but after setup copies the files and restarts to begin the installation and right where it says "starting windows" it just hangs there without continuing the installation. I rewrote the mbr and bootsector from recovery console but still nothing. I also reformatted and tried win2000 pro but same thing happens. I noticed the bootup password in the bios is set to enabled but I'm not allowed the option of changing it. Not sure if that has anything to do with the startup problems. Thanks for any help.
 

Read other answers
RELEVANCY SCORE 41.2

My daughter's friend in her classroom enabled the pass on her laptop as a joke. Now the joke is not so funny since she can no longer access any information off of the laptop. Can anyone help me in resetting the Master Password. The Laptop is an Omnibook 4150. I managed to get the hashcode which is "15043". Hopefully someone can help me out.

Than You
 

A:HP OmniBook 4150 Can anyone help me to reset the Password

Why not just ask her classmate what the password is? Is this the password at the initial startup (BIOS) or password at the login prompt?
 

Read other 5 answers
RELEVANCY SCORE 41.2

Hi,

i would be gratefull if somebody can give me the bios password .
My hascode is 00589

thnx in advance.
 

A:Hp Omnibook Xe4500 Bios Pass?

Please try
Clear CMOS
http://www.esupport.com/techsupport/UTILS/clrcmos11/clrcmos.exe

This will need to be run from a startup floppy or boot Cd
It will clear out the cmos fully (and hopefully your password)
 

Read other 3 answers
RELEVANCY SCORE 41.2

Would somebody please help to convet the BIOS hashcode 13360 for the HP Omnibook 510? Please email me at [email protected] I will very much appreciate it.
 

A:HP Omnibook BIOS Hashcode Converter

An algorithm for Omnibook hashcode converter is also good enough. Please!
 

Read other 2 answers
RELEVANCY SCORE 41.2

Hello,

J have got a problem with my Hp omnibook 6000

My hash code is 08958 - could you give me password?



Please help me R E M Z I B I


Many thanks
 

A:HP omnibook 6000 HASH CODE

Read this:
http://www.cgsecurity.org/cmospwd.txt
 

Read other 4 answers