Over 1 million tech questions and answers.

help is this a hardware problem?

Q: help is this a hardware problem?

I had to reset my computer to factory settings awhile back. I've done nothing to it except download advanced system optimizer and windows antivirus. This was a miracle alone due to the fact that my Computer locks up for extensive periods of time and will barely ever finish a task; such as transferring a picture to USB drive, scan, or any click command. It has never done this before the reset. I've had to reset my laptop several times before, it got to a point everytime I slipped up and left the battery unplugged with it running, start up repair would start and just about everytime could not fix itself leaving me no choice but to reset. Quite aggravating. With spurts of patience here and there I've managed to update all drivers, scan, use windows solution and nothing works. Sometimes it will run smooth for two minutes, then it's waiting and quite possibly never accomplish anything. I can't get my pictures which is my own fault for not backing up. I've tried linking my other laptop to get the pictures and the bar never moves once it gets towards the end. Any ideas?

RELEVANCY SCORE 200
Preferred Solution: help is this a hardware problem?

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: help is this a hardware problem?

With a laptop you do not have a lot of hardware debugging choices. But I would try this:

1. Take one of the memory Dimms out and run it on just one Dimm. If it is still on the blink, try the other Dimm. If it runs OK, you know it is the memory Dimm in question and can change that.

2. Burn a Linux CD - e.g. Puppy because it is small. Run that from the CD reader (change the BIOS boot sequence). If that works well, you know it is a Windows problem and we can dig further.

You can also run step 2 before step 1 if that is more convenient. If none of those steps shed any light on the problem, we'll have to regroup. There can be many other causes.

Read other 9 answers
RELEVANCY SCORE 40

I m facing this video hardware error from last 1 week in my HP G62 361Tx Laptop.
Laptop Cooling fan is working Ok. no Abnormal sound.
I have installed TechPowerUP GPU Z to check GPU Temperature..
Min Temp.-> 52 degree centigrade
Avg. Temp-> 72 degree centigrade
Max Tamp. -> 84 degree centigrade
I m attaching follwing file:
WD-20130329-1304.dmp
sysdata.xml
WERInternalMetadata.xml

Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows 7 Ultimate, Service Pack 1, 32 bit
Processor: Intel(R) Core(TM) i3 CPU M 370 @ 2.40GHz, x64 Family 6 Model 37 Stepping 5
Processor Count: 4
RAM: 3061 Mb
Graphics Card: ATI Mobility Radeon HD 5470, 1024 Mb
Hard Drives: C: Total - 51743 MB, Free - 20209 MB; F: Total - 108149 MB, Free - 11567 MB; G: Total - 145237 MB, Free - 10863 MB;
Motherboard: Hewlett-Packard, 1426
Antivirus: Norton AntiVirus, Updated and Enabled


Description
A problem with your video hardware caused Windows to stop working correctly.

Problem signature
Problem Event Name: LiveKernelEvent
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 1033

Files that help describe the problem
WD-20130329-1304.dmp
sysdata.xml
WERInternalMetadata.xml

View a temporary copy of these files
Warning: If a virus or other security threat caused the problem, opening a copy of the files could harm your computer.

Extra information about the problem
BCCode: 117
BCP1: B3C4F008
BCP2: 99FC68B0
BCP3: 00000000
BCP4: 00000000
OS Version: 6_1_7601
Service Pack: 1_0
Product:... Read more

A:Video Hardware Error-A problem with ur video hardware caused Windows to stop working

Read other 16 answers
RELEVANCY SCORE 37.2

i have put together a new pc put of these parts

AMD 64 x2 athlon 5600+, Asus Crosshair motherboard, EZ cool power supply 550W on the 12v it has 36 amp, and i have got a Geforce BFG 8800 GTS OC graphic card, 2 gb of DDR2 elixir brand,

the problem is when i try to boot it up nothing appears on my screen i dont know what the problem could be, checked all connection everything is connected, including power to the graphic card, maybe it could be DDR or Power supply or simply my grapgic card faulty??

thanks in advance for any help
 

A:Problem with my hardware hardware please help

Read other 6 answers
RELEVANCY SCORE 36.8

i have acer e1-571 notebook.running windows 10.from last few days my pc giving this error-Currently, this hardware device is not connected to the computer. (Code 45)

To fix this problem, reconnect this hardware device to the computer.

A request for the USB device descriptor failed.                                                            
                                                                i have tried all kind of suggestions
given by microsoft related this problem .but   cant solved.card reader ,pen drive ,external keyboard ,or external mouse no one working.2.some  random  keys  is not working .please fix my issue .

Read other answers
RELEVANCY SCORE 36.4

Hi guys,

About two months ago I bought an Acer TimelineX laptop (the 11.6" version with the i7 core.) Last night it started havong some vicious problems. It will instantly shut down or freeze with the current displayed graphics being very distorted, seemingly at random intervals. I suspect a hardware problem because a few minutes before all this started I noticed the cover protecting the internal components was out of place, so I snapped it back into position.

I tried running some of the pre-boot Windows diagnostics, but they came up clean. The system crashed once during this process and gave me a blue screen of death that said "PFN_LIST_CORRUPT". I ran a diagnostic on the memory and it came up clean as well. I'm thinking I might have broken some critically important piece of hardware. Anybody have any ideas? Thanks!

-Kai
 

A:Problem with Acer TimelineX turning off/freezing, suspect a hardware problem

A few silly ideas that i've tried with my Acer ..
try taking the battery out !..
just run it off the lead..
I've been told its something to do with a hardware issue with the standby mode of the fan or the CPU or some standby/neutral position that some gizmo inside does (have you guessed that I'm no techie ;o)
Try it out, it could be a simple (if not permanent) fix.
Good luck
 

Read other 1 answers
RELEVANCY SCORE 36.4

Good afternoon Tech Immortals,

I am working on a friend's computer.
The hardware setup is the following:

AMD Athlon 64 X2 Dual Core Processor 5000+ 2.1GHz

2.5 GB RAM CRUCIAL (Memtest says the following about it: DDR2(64 bit)
373MHz DDR746 CAS: 5-5-15

Nvidia GeForce 9800 GT pci-e

MSI K9N6PGM2-V motherboard

The problems:

Problem1. When the computer is turned on it gives out 2 short beeps (memory error, I presume according to an Internet search). Then it loads GRUMP for Ubuntu 9 or Win XP pro
Problem2. Anything that is graphics intensive makes the computer crash or graphics get glitchy. For example videogames will either make windows crash or crash the game and exit to windows. On Ubuntu while running Compiz the OS freezes. It only crashes or glitches with graphic intensive software.

Solution tried:
For problem1. While loading GRUMP there is an option for memtest. Diagnostics came out fine, no errors.

More background information:
I've inspected the motherboard, the graphics card, ram, everything (looking at it physically for any burns or liquid spills etc)
Everything is roughly 4 months old, bought brand new when purchased.
In the past the user had the same setup except that his old graphics card (GeForce BFG TECH 8800 GT) died on him (will get further details about that in about an hour).
Replaced for graphics card mentioned above. Those problems are occurring.
The card gets warm, but not to an alarming point (I want to say around 60 degrees celcius).... Read more

A:Solved: Interesting Hardware problem (Nvidia graphics problem possibly due to RAM)

It was a faulty video card.
User replaced it under its warranty.
 

Read other 1 answers
RELEVANCY SCORE 36.4

Hi, I'm in need of figuring out if my laptop was infected by a trojan, the operating system went kapoot and i need to reinstall it, or if its hardware failure. I used it last night and my AVG caught a "small trojan horse" called cryptbase.dll and after removing it i believe is where it began. My computer restarted and ended up starting up with the acer splash with me able to click f2 for setup. But f8 doesn't work and causes a long beeping noise if i leave it alone it goes to a black screen with a underscore blinking at the top left. i've done some research but, im unsure which route to take without taking some advice for my own laptop. My laptop is a Acer Aspire 5741-3541, Windows 7,intel core i5-450 processor, 4 GB DDR memory, 500 GB HDD. if you need more information please ask because im unsure with what is needed to fix the problem. The solutions i've heard is reinstalling windows 7, or it might be a HDD problem. Thank you.

A:Unsure if virus, operating system problem, or hardware problem

Let ma ask someone to look here.

Read other 52 answers
RELEVANCY SCORE 36.4

Okay, right now I'm currently trying to find out whats wrong with a keyboard that is on a laptop, after the computer starts there are some script errors, I don't know exactly what they are but I ran combo fix without safe mode and restarted the scripts went away...and it started working after restarting a couple times it started to work then restarted more the scripts came back and the keyboard stopped, even in safe mode but after five or so minutes the keyboard was able to type again, I checked the device managers and everything is update and no error, I ran a combo fix and have the report if you guys want to see it let me know, Its an HP DV6 series with 64-bit windows 7 OS, I'm stumped I have no idea whats up, I'm ready to just put in the recovery disks and see whats up, but he has like 250 gigs worth of files Games etc, Can I back it up to a hard drive and install go back to where it was normally or can that be a problem?

A:Laptop Windows 7 Problem/Software/Hardware? Keyboard problem

Bump

Read other 2 answers
RELEVANCY SCORE 36

Hi, I'm new here (meaning I just made an account but have been lurking around every time I had computer trouble. This time however, I couldn't find anything that resembles the trouble I'm currently experiencing) and I'm hoping if anyone can help me or tell me if I should just throw my laptop against the wall.

I've had my printer (details and TSG SysInfo below) for over a year now, and never had any trouble with it. A few days ago, I needed to print something but wasn't able to (I can't remember what the error said, it didn't happen again) so I uninstalled the printer and re-installed it by downloading the drivers from the HP website. Pop-up balloon said that it wasn't successfully installed and when I would try to install the driver by going to print management and click on Printers I would get: "An error has occurred on the script of this page. Line: 40. Char: 21. Error: Object doesn't support property or method 'SetPrinterName'. Code: 0. URL: res://C:\Windows\system32\pmcsnap.dll/81". So I clicked on Drivers instead and tried to install the driver there and it said: windows found driver software for your device but encountered an error.

Do understand that I have no idea what I'm doing whenever my computer doesn't behave as it is supposed to, and everything is done by trial and error; mostly error. For some reason I felt the need to do a chkdsk /f /r which was scheduled on the next restart, b... Read more

A:printer problem? software problem? hardware problem?

Howdy,
Could be the Hard drive has gone faulty. What make and model is this Laptop?
 

Read other 2 answers
RELEVANCY SCORE 35.2

The short version of my problem is that at some point after a reboot, certain web pages fail to load.  I'm not sure what the root cause is, at all.  I am running Windows 7 SP1 and was up to date with updates when this started.
 
When it started happening:
Thursday night, the power flickered at my apartment and made my computer reboot.  I figured it was a good a time as any to install Windows updates since I hadn't done that in a while.  After doing so was when I first noticed the problem.
 
The problem:
What happens is after I reboot, at first, everything works fine.  At some time after, some web sites just don't load.  The sites that don't load are consistent (if I reboot and wait, all the same ones fail).  A couple examples are bleepingcomputer.com itself and any of Valve's (the game developer) sites.  It doesn't seem that computer help/anti-malware sites are all not working, since MBAM and AVG's sites work.  Google itself always works and when Googling for info on this problem, I seem to find more sites that don't work than do, once it starts happening.
 
I don't know specifically at what point stuff stops loading.  I tried rebooting then going to read a book for an hour, and it was working when I tried immediately after.  If I reboot and open Firefox with a ton of tabs and start browsing around, it might stop within a few minutes.
 
What I tried:
At first I thought it was my Internet connection or ... Read more

A:Infected? Hardware problem? Software problem?

Hello knismaps, let's see if we can find something.

Please download MiniToolBox, save it to your desktop and run it.
Checkmark the following checkboxes:
Flush DNSReport IE Proxy SettingsReset IE Proxy SettingsReport FF Proxy SettingsReset FF Proxy SettingsList content of HostsList IP configurationList Winsock EntriesList last 10 Event Viewer logList Installed ProgramsList Users, Partitions and Memory size.
Click Go and post the result (Result.txt). A copy of Result.txt will be saved in the same directory the tool is run.
Note: When using "Reset FF Proxy Settings" option Firefox should be closed.

Download TDSSKiller and save it to your desktop.
Extract (unzip) its contents to your desktop.Open the TDSSKiller folder and doubleclick on TDSSKiller.exe to run the application, then on Start Scan.If an infected file is detected, the default action will be Cure, click on Continue.If a suspicious file is detected, the default action will be Skip, click on Continue.It may ask you to reboot the computer to complete the process. Click on Reboot Now.If no reboot is require, click on Report. A log file should appear. Please copy and paste the contents of that file here.If a reboot is required, the report can also be found in your root directory (usually C:\ folder) in the form of TDSSKiller_xxxx_log.txt. Please copy and paste the contents of that file here.
.
.
.
ADW Cleaner Skip or rerun it.

Please download AdwCleaner by Xplode and save to your Desktop.
Double click on AdwCleaner.ex... Read more

Read other 3 answers
RELEVANCY SCORE 35.2

I got a virus so i replaced the hard drive . when i try to install the windows 7[ from the factory] it would closes every 15 minutes. Ok I finished took time but it kind of worked . Problem if my computer closes or if i close it. it will not restart . unless i push the power bottom on, crash the computer, by removing the battery and power cable , wait at least 4 hours, then it will restart and work ok. everything works, but it has trouble downloading some larger files what are reasons a computer will not start the fan works and one indicator light works but it would sit all day and do nothing .I had a business and 4 computers came down sick at the same time but they had different operating systems so they react differently this is the only one i have saved i tried changing the hard drive in two others but i can not restart them what part of the computer tell it to turn on ? thankyou very much
 

Read other answers
RELEVANCY SCORE 35.2

Yesterday, I came home from work to see that my computer had done a reset on its own. When I turned it on, I found the Win 10 Anniversary update waiting for me. Since then, I have had several crashes with games, and even blue screens.

The BSOD's go by so fast, that I had to turn off the automatic restart just to read the error as STOP CODE: MEMORY MANAGEMENT. Apparently, this means that there is a problem pertaining with my RAM.

A few months ago, I came on here with a similar problem after my PSU blew and I had to get anothr one. I solved that by buying 2 new RAM cards to replace the ones inside. I ran a memory diagnostic which showed no problems, and right now I'm running a system file check scanner as well. If both of these come back fine and there are still problems, I may have to get new RAM sticks.

I have a 2 year warranty on them, so replacing them again would be no problem. However, before I do that, I was wondering if the problem might be my motherboard or CPU as they are the only components still used from the computer from when the Power Supply blew? These would be my 3rd set of damaged RAM cards in a year, and that just strikes me as weird, especially since they are designed to withstand overclocking conditions.
 

A:Unknown hardware problem (possible software problem)

As the computer shut dow/reset for some unknown reason, I'd suspect that unknown event to be related.

Could be power related (ie: power surge or dirty power), power supply (if you are using a non-Tier one model, or possibly the motherboard.

Bottom line, some event occurred which caused this issue and it likely isn't related to previous issues.
 

Read other 3 answers
RELEVANCY SCORE 35.2

Hi all, I was hoping someone could help me out. I've been having a reoccurring issue with my laptop. The basic issue is that it runs very, very slow - using about 80%-100% of the CPU when a program is open and 30%-50% of the CPU when no programs are open. If I try to restart the computer, it will hang on a black screen between the "Starting Windows" screen and the "Welcome" screen.

The first few times it occurred (July, October, and mid-November) a System Restore from Safe Mode solved the issue. The fourth and fifth times it happened (late November and early December) I had to try restoring to multiple different restore points before it would work again. The sixth time (mid-December) no amount of System Restores did anything. I ended up running the "sfc scannow" command and that seemed to solve it. The seventh time (late December) neither System Restore nor "sfc scannow" did anything. I ended up reformatting and doing a clean install of Windows. That solved the problem for about a week, then last night it started happening again.

I'm a little lost at this point. I've run tests on both the memory and hard drive and they came out fine. I looked through the event logs each time the issue occurred and didn't see anything that seemed likely to cause this. The fact that it keeps reoccurring, even after a clean install, makes me think it's some kind of hardware issue. But the fact that the computer works completely fine... Read more

A:Strange Problem - Not entirely sure whether it's a software or hardware problem

Hello and welcome.Use Process Explorer to provide an overview of your running processes.Download the .zip file and extract to a folder on your desktop. Run program. In Vista/7: Click File > Show Details for All Processes.Click View > Select Columns and check the Command Line box. Click OK.If necessary, continue to use the computer until it displays the undesirable behaviour (lagging, freezes, etc). Immediately switch back to Process Explorer and press the Space Bar to pause updates.Click File > Save As.... Save to your desktop as procexp.txt.Attach (do not copy & paste) procexp.txt to your next reply. Use the forum's "Full Editor" to attach files.Note: Do not unpause or exit Process Explorer unless directed to.==========================================Use Speccy to provide details of your computer's configuration.Download, install, and run After Speccy has finished gathering information, click File > Publish Snapshot In the Publish Snapshot dialog box, click Yes to enable Speccy to proceed. A web address will be displayed, click Copy to Clipboard and paste it in your next post.=========================================

Read other 12 answers
RELEVANCY SCORE 35.2

I've got serious problem with my Radeon 9600PRO:

I installed Win XP SP2 on my new PC, Windows detected a new VGA device, it tried to install default drivers but it couldnt find it, (although WinXP CD was in a drive, and internet connection was working)

I installed DirectX9 and then launched the latest Catalyst Setup downloaded from ati.com, and installed drivers. After that, my card was noticeable as HIS Radeon 9600 series properly for Device Manager.
However, it didn't work well - in CCC there is 3d a graphic test - with 3d preview - a car driving on the road - and on my display it wasn't looking good, image was blurred or sth, also the icq icons were blurred (flowers and smiles) - while after uninstalling ATI drivers, when card is seen as a default VGA device (default frequency of monitor, default resolution) icq icons are looking well...

With Catalyst Control Centre installed, after reboting my display goes blank, and the only solution is reboting in safe mode, unistalling ATI drivers, and installing them once again, then it works but until the next rebot in normal mode...

Anyone knows what' the problem is? Rahter software or hardware?
Mayby Radeon 9600Pro cann't work properly with Athlon 64?
Maybe I should change something in BIOS?

My hardware:
HIS Radeon 9600Pro
Epox 8KDA3+ NFORCE3
Athlon 64 3200+
 

A:Problem with drivers for Radeon9600Pro or problem with the hardware?

Did you install the motherboard and AGP drivers?
 

Read other 2 answers
RELEVANCY SCORE 34.4

I currently have my Benq monitor set to the default resolution of 1280x1024 but have changed the DPI to 120% for better viewing. Since I did that all the excel worksheets I had been working on for the past year don't appear correctly as I had meticulously set them up & saved them with the monitor set on 125% DPI . I can revert back to 120% but I want to save the files to disc for my family and want them to be able to view them in the same way I had set them up. I have tried many monitors of various sizes on my PC but with the same result. So it doesn't seem to be a monitor problem ? I thought that changing the monitors DPI would only make items appear larger or smaller not affect saved worksheet files.
There is no other setting I can find to alleviate this problem so wondering if it is a hardware problem ? Hope someone can offer some suggestions

A:Hardware problem ?

How is it not appearing properly? Are some of your values appearing as 'xxxxxx'?

Read other 3 answers
RELEVANCY SCORE 34.4

Hello, my computer was working fine over the weekend, i moved my computer back to another area of the house, it was working fine until now, whenever i start it up, i can hear it running, but no display on the monitor and it keeps making this kind of long beeping sound, then it stops, repeats forever... i don't know what caused this or how to fix this, this computer is kind of old, i play all my old games on it. (bought in 2004) It is running windows xp professional, and 512MB of ram, can anyone help me please? i have snapshots of my computer if you would like me to upload. Thanks.
 

A:possible hardware problem?

Please post your system specs, To include Make and model System if Big Box, or same info for the following if custom or home built, Mother Board (including Revision number), Processor (Exact Model Number), Ram, Video Card, Hdd(s), Optical Drive(s), Power Supply Manufacturer Model, Wattage and Amperage on the +12V Rails, OS, and any other peripherals installed on the motherboard.
 

Read other 2 answers
RELEVANCY SCORE 34.4

my bluetooth device is installed but couldn't transfer file either from laptop to mobile or mobile to laptop, though it shows paired and connected. whenever i try to send or recieve file it shows a message" an address incompatible with the requested protocol was used ". in device manager there is unknown device which id is "ACPI\VEN_INT&DEV_3400", another device id "PCI\VEN_8086&DEV_1903&SUBSYS_81EC103C&REV_08", another id "PCI\VEN_8086&DEV_9D3A&SUBSYS_81EC103C&REV_21" . i need driver for these.  plz do reply asap

Read other answers
RELEVANCY SCORE 34.4

I have a Dell Dimension 8400 running Windows XP.
In the past 36 months I have had 6 DVD and CD drives replaced in this computer. The problem is always the same in that the tray gets to where it will not open. I open it with a paper clip and the tray is loose and free moving. A couple of times I have seen the small drive belt and it is broken. I have gone through 2 (20X Liteon) drives in the last 60 days with very limited usage. I am the only user of the computer and extremely careful so I know the tray is not being beat up and abused. Would appreciate any help someone may offer.
Thanks---
 

Read other answers
RELEVANCY SCORE 34.4

Hey all,
Ok, here's the problem, hope someone can help. I've recently had problems with my comp, it wouldnt boot. I'd been having problems with my 80 gig Western D. Hard drive so i replaced it assuming it was the problem and it was still under waranty. I can now boot to the windows instalation setup. I format the hd, create a partition and begin the instalation. Windows writes the instalation files to the hard drive, and is supposed to reboot and load from there to continue the instalation. Well my comp reboots, but takes me right back to the initial setup screen. It's not detecting the instalation at all as if i didnt install anything, but i go into dos cmd mode and i see the windows folder, so the hd is being written to. Ive even tried switching cables incase they were bad. Bios was reset a couple times, dont know whats wrong here. Its like its writing hd, but not reading, what to do? A couple times i have gotten could not detect boot volume error also. thanks for your time.
-Dan

"in case it matters,
mobo: asus p4s533 intel p4 2.0ghz , 80 gig western digital hard drive special ed. 8 mb cache. If any other parts matter let me know."
 

A:Hardware Problem

Had the exact same thing happen a few weeks ago helping a friend put together his new computer. try this, if the WD is the ONLY hardrive or device on that IDE channel remove the jumper from it. the WD's dont like having a jumper if they are alone on the IDE channel. ( not even if it is set to master)
 

Read other 19 answers
RELEVANCY SCORE 34.4

i'm using an athlon cpu with a jetway board and recently my pc just shuts down and restarts when im using it. no matter waht application i've been using sometimes after 10+ mins or less. then i tried to remove all hardwares and inserted it again. at first it works it doesnt restart but when i use games such as nba and nsfu after several mins it shuts down and restarts. so i cant play games so i tried to format my disk but after formatting i cant reinstall xp my pc works to slow as if it was an pentium1 with 8mb of ram. it takes too long to go to the windows setup. it reads data too slow. what could be wrong? need your help pls thanks
 

A:Hardware problem?

you need to clean the harddrive out good, FDisk is preferred, but ask more people on this site and they may know of some good programs to clear it out.
 

Read other 3 answers
RELEVANCY SCORE 34.4

I have only one USB outlet on a WinXP Professional and when I use Add New Hardware I get malfunction, hardware not recognised, installed but may not work, unknown device, drivers not found and so forth. I have shown the path etc but nothing, tried unknown device same thing. There are some devices installed ok. I have tried the items (Mobile Phones) I am trying to install on another computer and they will install. Please what can be my problem.

A:Add New Hardware problem

mmhhh, What i think is that you mait not install the device properly, or try to change the usb that you are using this would work most ,When a USB is used to be unplaged without stoping the process it would probably coused the USB not to be recognized next time you plug it in.

If it says drivers not found ,go to device manager and look for the drivers on the internate.

Last try to check for the firewall settings may firewalls may be stoping the device due to some problems that occurs during installation.

Hope you mait find something useful.

Read other 19 answers
RELEVANCY SCORE 34.4

Hey guys, ever since I came back from vacation a couple months back, my computer has been freezing after about 10 minutes of use. When I say freeze, I mean, the image on the monitor is frozen, and the mouse + keyboard are unresponsive. I tried swapping out RAM, the harddrive, the power supply, and I tried it without the graphics card. Plus I replaced my mobo. Also, I know it's not a software problem because it froze in BIOS before, and it froze when I put in a live CD.

Anyone have an idea as to what is going on?

Edit: Also, here are my specs.

Motherboard: http://www.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=170&prod_no=1426
CPU: Intel Core 2 Duo E2200
GPU: NVIDIA GeForce 9800 GT

Edit Two: Temps and Voltages taken from Speedfan.

GPU: 57
Core: 57

VCC3V: 3.44v
VCore: 1.34v
VRAM: 2.21v
VChipset: 1.25v
+5v: 5.09v
+12v: 11.97v
VCC1.5v: .90v
VSB3v: 3.44v
VBat: 3.10
 

A:Hardware problem?

Things you can do>run anti virus>remove old programs>delete temp files>from start go to run type in chkdsk /r [note space between k /] defrag
 

Read other 2 answers
RELEVANCY SCORE 34.4

hi guys im totaly new to hardwares and for a long time my compute was making noice and use to stop and shut on its own. when i opened it i found there were 2 fans, one to the main power supply box and the other one by the mother bord . what i see is the power suppply fan is not at all working and the other one is actually making the noice, it doesnt run continuosly ,it stops and then start again and so on.then all of a sudden the computer might turn off on its own. can any one suggest me whats going on or is there any other problem.please suggest what should i do myself as its too expensive to take it to shop.
 

A:possible hardware problem

Read other 8 answers
RELEVANCY SCORE 34.4

So yesterday I try and boot up the computer, but it makes a beeping noise (one) and the monitor fails to be recognized. I decide to move my ram (2 sticks) to the Dimm 2 and Dimm 3 spots instead of where they used to be, Dimm 1 and Dimm 2, I boot up, and the monitor is recognized again. However, I get windows wasn't shut down properly message, I go with normal startup, and it freezes during the windows loading bar. I restart, choose safe mode, restart once in safe mode, and I am able to get it working. Next I noticed that my sound wasn't working, check my device manager and see that the Creative game Port and main Audigy driver's aren't installed properly now. So I reinstall the audigy drivers, which worked, and then try the game port but it won't install. After trying many times I look around to the net to see what the problem could be, and decide to look in the BIOS. I see that onboard game port is disabled so I enable it, try to install the driver but it still won't work, so I went back into BIOS and disabled it again to be safe. Frusterated and getting late I went to bed. This morning I try and boot up again and it freezes during the loading screen again. After going to safe mode and restarting a few times over it finally works. Now my question is, is my sound card defective and could that be causing XP to freeze? And What did switching my ram slots have to do with all this?
 

A:Hardware problem?

Read other 13 answers
RELEVANCY SCORE 34.4

My lappy showing Hard disk test failedBoot device not found

Read other answers
RELEVANCY SCORE 34.4

Hey there,

I was just wondering if i could have some help with my PC please.

When I switch my PC on, a series of beeps comes from my motherboard.

It's a beeeeeep which goes on for roughly around a second, then a second with no beeps, then another beeeep, and this continues until i decide to turn off the PC by the switch.

I've tried placing my RAM in different slots, but it doesn't work.

I would greatly appreciate your help

thank you in advance
 

A:Hardware Problem ...

Read other 16 answers
RELEVANCY SCORE 34.4

My system crashes. often. most reliably it crashes when i am playing diablo 2 on battlenet. it could go an hour, or maybe 3 minutes. it seems to go the busier the scenes are, though sometimes crashes when nothing is going on. sometimes it just reboots, sometimes the game just crashes and i can restart again right away.
i upgraded my video card and the crashes are still happening.
also, stable programs like yahoo msgr crash with a "yahoo messenger has a problem and needs to close now" window. control panel, my computer, random system software hangs up and needs to be closed via task manager (program not responding).
sometimes "services and apps" goes awry and i get a window telling me to save my work in 60 secs because it's about to reboot.
i reformatted not long ago. also i defrag, and scan for everything religiously (ad-ware too, i run all the major programs). i have 4 fans and the hard drive is sitting under the air conditioner.
arg!
 

A:could this be a hardware problem?

Read other 11 answers
RELEVANCY SCORE 34.4

yellow ? mark by keyspan usa 19 h

A:hardware problem

install the device driver that came with this USB device....

http://www.tripplite.com/en/products...xtModelID=3914
what do you use it for?

Read other 1 answers
RELEVANCY SCORE 34.4

First time here, so I must be in dire need of help.

Here's my problem, last night I opened an email and it said the sender was my mom. All it had was a link, and like an idiot, I clicked it. Laptop has been downhill since then. I have windows 7 if that helps in any way.

Here's the problem:

When I turn on my computer, everything boots up fine then it stops and says Windows Explorer stopped working then tries to restart. It will do this an infinite amount of times. I've tried sfc/scannow and it does nothing, it's gone to a black screen and went through all the drives and done nothing, I've ran Microsoft Security Essentials, Spyware, Malware Bytes, and AVG to no avail. It freezes constantly. It says one of the drivers or drives is corrupt. I also tried to do System Restore, but it says there are no System Restore points.

Any help would be much appreciated.

A:Hardware Problem

Go to Start/Search and type chkdsk C: /R and press enter. Now type a Y and reboot the computer. the Check Disk utility will run at next boot up and try and fix any file errors. Do this for all the drives on your computer. Also download the ISO image for Drive Fitness Test in my signature and burn the image to a CD using IMGBurn also in my signature. And boot off of the newly created CD and run the short and extended tests on the HDD.

Read other 4 answers
RELEVANCY SCORE 34.4

I also had the same problem while running XP.
When i play COD4 a couple of problems started occuring... the keyboard switched off and on while running the game and then at some point just off, the only way i could get it back working was to either log off and back on again or restart. Playing Rugby 2008 nothing happens and everything is fine. Playing Modern Warfare 2 the pc stops responding completely and needs to restart.
I also need to add that my keyboard is a usb one. But it never gave me problems EVER.

Can the Page Faults per second be the cause?
While playing COD 4 the maximum Faults per second is over 12000 and averages around 600. While it is idleing it averages around 30 - 40.
The other things i monitored are:
Disk qeue length : 1.2 max, 0.07 average
CPU interrupts per sec: 1572 max, 619 average
%interrupt time (CPU) : 1.6 max, 0.349 average

While playing Rugby 2008 all the stats are less... Page faults down to 9000
The only significant change was the disk qeue length which is now max 0.069 and average 0.005.

I have updated everything as far as possible (drivers, software... everything). Still the problem continues.

And i was away for 1 month and after returning home this is what i returned to... Definately not a happy chappy
 

Read other answers
RELEVANCY SCORE 34.4

Hi! I recently assmebled a new CPU and its been giving me trouble. I have a Intel 2.4 GHZ core 2dual proccessor on a Intel 945GCNL SND/VGA NIC Motherboard with XP Pro loaded.It started out well but then a message was displayed "A problem has been detected and windows has been shut down to prevent damage to your computer
The problem seems to be caused by the following file igxprd32
If this is the first time you have seen this stop error screen restart your computer. If this screen appears again follow these steps.

The device driver got stuck in an infinite loop.This usually incicates problem with the device itself or with device driver programming the hardware incorrectly.

Please check with the hardware deivice vendor for any further driver updates".
I went to the Intel website and downloaded the driver updates and tha BIOS update installed it also. It seemd to be okay for some time and then the same thing happened again. What could be done? Please Help! Thank You.
 

A:Problem with the new Hardware Help!!

Read other 11 answers
RELEVANCY SCORE 34.4

I do not have a OS on this system quite yet, as it has just been put together.

Now then, I'm having some difficulties...everything seems to be wired up correctly, but when I power up the system it runs for just a few seconds then shuts off..and the screen never goes into the BIOS, it just stays black. After a few retries it then decides to power on and stay on and let me set up the BIOS.

Anyone know what the reasoning for this might be? It seems to be powering on just fine now, but it still makes me uneasy about the whole ordeal.

Thank you,
-Xen00b

A:Hardware problem

Hi Xen00b,

Perhaps, it just needed a few startups to reset itself. ??

If it is running fine now, I would not worry about it to much.

Shawn

Read other 2 answers
RELEVANCY SCORE 34.4

I cant save any data in one of my drive.When i tried to save anything it says "some data loss due to hardware or network failure"...And i couldnt format da drive to ntfs..Only it formatted to fat32...Whats the possible defects?I usd scan disk.No problem found,,
 

A:Hardware problem

The drive you are trying to save data to... is it inside your computer or is it an external drive? Is it a drive that is somewhere else on a network? Please tell us a bit more about your set-up.
 

Read other 1 answers
RELEVANCY SCORE 34.4

Hi everyone, i have a little problem here my pc work normally, but when i start a game or a program my processor start overheating! Normally 70 degree and than he go to 105 degree after 1 sec the Core speed is dropping and im bugging. It's a 3.40 GHz and dropping under 2.5 or less ..

Read other answers
RELEVANCY SCORE 34.4

i get a gray volume box in middle of screen comes and goes whenever it wants to. ive ran norton and spybot and nothings help. i dont trust a lot of the free spyware programs.starting to think its not a ad ware problem at all??? a real pain
 

A:can anyone help is it a hardware problem??

Does your monitor have built in speakers ? Maybe it the monitor's on screen controller.
 

Read other 3 answers
RELEVANCY SCORE 34.4

I bought a dell laptop just over a year ago, and about 6 months in had a major hard ware failure, but to this day have never figured out what it is, basicallyt its a blue screen error that randomly comes on at first it was a rare problem occuring once or twice every week basically its an error that says the computer was shut down to prevent damage there was a probelm with somethign somethign something (running windows xp)

then the error became more frequent and by the end the windows xp loading screen would come on and it would crash then ever time.

now obviously after re formatting a 100 times and the error reoccuring i rang dell and they started replacing bits

first the hard drive, then the hard drive again, then they replaced the mother board and cpu basically every important componant

eventually i got so fed up of ringing i sort help online and luckily found somone i knew on a forum worked for dell, he managed to get my laptop replaced and all wads well

as luck would have it, they forgot to pick up the laptop so i still have it here with me

so as you can imagine i would like to fix it myself as there is no point keeping a bust laptop around

yesturdasy i install windows 98 no probelms and am goinna try putting xp back on, but i dont htink it will work for long
basically the laptop is fine except for this error

the only other problem is the modem stopped working which i have just removved incase that was cvausewing the problem
anyway anyone have any idea what ca... Read more

A:Hardware problem

Basically it could be anything, and RAM would be the first thing I would look at. Most graphics cards are built into the motherboard on laptops so that may have been replaced as part of the motherboard. You can download a memory tester from here: http://oca.microsoft.com/en/windiag.asp and run that. Press T to run the extended tests.

If the laptop is indeed yours to do as you wish then I would sell it; people will pay nicely for the LCD panel alone. However, DELL probably wants it back as they put several new parts into it and they almost always want their parts back no matter what.
 

Read other 2 answers
RELEVANCY SCORE 34.4

Hello everyone

I have 2 big problems with my computer
1)My graphics card is crashing when i am playing some games for example League of Legends and COD Black ops after their loading screen my pc crashes some times both games work but sometimes they dont

My second problem is that i bought a duo ram (2x2 4gb) and every time i try to boot it either stops at the beginning or after windows logo i get a blue screen

Sorry that i provided so small info but i am tired and depressed too a very deadly combo
 

Read other answers
RELEVANCY SCORE 34.4

COULD NOT FIND SOFTWARE DRIVERS FOR COPROCESSOR

OS Version: Microsoft Windows 7 Home Basic, Service Pack 1, 32 bit
Processor: AMD Turion(tm) 64 X2 Mobile Technology TL-50, x64 Family 15 Model 72 Stepping 2
Processor Count: 2
RAM: 958 Mb
Graphics Card: NVIDIA GeForce Go 6100, 64 Mb
Hard Drives: C: Total - 20002 MB, Free - 13118 MB; D: Total - 34808 MB, Free - 18894 MB; F: Total - 39644 MB, Free - 32265 MB; G: Total - 19999 MB, Free - 8942 MB;
Motherboard: Quanta, 30D3
Antivirus: AVG Internet Security 2013, Updated and Enabled
 

A:Hardware problem

You need to install the Windows 7 Chipset Driver from your laptop maker's website.
 

Read other 1 answers
RELEVANCY SCORE 34.4

My computer:
asus p5kc
inno3d 8800 gts 512
4 gb ram mushkin
750 gb samsung hdd

ive got problem with some hardware.sometimes when i boot up computer,the windows boot screen doesnt shows.it just freezes when it should apear and i get a blank screen.but if i reboot again everything goes normal (except windows shows message that it could not load becouse some new hardware was added)

what should i do to get rid of theese freezes?
 

Read other answers
RELEVANCY SCORE 34.4

I recently acquired an old server, and can't get it to work properly if I want to turn it on I have to change the power input. Also it works off two C drives and I can't update the OS (Well I did install XP but if I try to use it nothing happens).
 

A:Hardware problem

What is this "old server"? Make, model, motherboard, memory?
 

Read other 8 answers
RELEVANCY SCORE 34.4

My computer froze a few days ago, and repeated this behavior after reboot. I re-imaged using various different Ghost backups and the same thing, screen froze. Occasionally I'd get the BSOD, and once it prompted a CHKDSK, which was about finished (showing no errors) when it froze again. It had also hung at various times during my attempted re-imaging (using Ghost). I've used Ghost on the same computer many times in the past with no issues. I was able to fully re-image if I let it sit overnight and tried again in the morning, but eventually the same thing, hung screen. I tried again by removing all but the bare minimum in terms of hardware, and same thing.

The only 'new' thing I've done lately is upgrade to the ViewSonic monitor using the PVI inputs rather than the traditional monitor input.

Would this be something potentially heat related? The fans seem to be in working condition, but I know nothing about the heat sinks, etc. Or could it just be a bad hard drive? I don't think it's a virus or anything because I've re-imaged to working times while not connected to the internet (but I could be wrong).

MSI motherboard (amd 64 4000), 1G RAM
Dual Serial 70G HD's (no RAID; One is C:, the other is for Ghost backups) + an older IDE HD for data. Echo Soundcard with 1/4" inputs. ViewSonic monitor (new), everything else is 2 years old

Thanks!
 

A:Hardware Problem?

Read other 11 answers
RELEVANCY SCORE 34.4

Hello, my 7 laptop has suddenly begun to misbehave.it sticks on the black toshiba screen when I switch on, it says F2 for something and f10 for something else, but Enter usually gets it to boot up. But then when it has booted if I go to a text program it gives an endless uncontrollable stream of = signs, same in the search box at bottom left, In qwicken it churns the date endlessly forward. Esc gets it out of this (usually) and it works fine.
Can someone point me to what is the problem? Is it the keyboard or is it a software mangle?
Does it sound fixable or is this my hint to dump the machine?
Thanks

A:? hardware problem or

Try this first:

Boot your PC with the "Last Known Good Configuration" option.
This quick little option can be accessed by following these simple steps:

Press and hold down the "F8" button as you boot up your PC and before the Windows logo is displayed. This will bring you to the Advanced Boot Options, wherein a list of options on booting up your Windows 7 system is provided.

Locate the "Last Known Good Configuration" option and select it by pressing the Enter key. Your PC should now start booting Windows. Wait and see if it works.

If that didn't work, try System restore.
System Restore

More related tutorials:
http://www.sevenforums.com/tutorials/666-advanced-boot-options.html
http://www.sevenforums.com/tutorials/69585-safe-mode.html

Lets us know if you have any questions.

Hope this helps,
John

Read other 2 answers
RELEVANCY SCORE 34.4

Hii sir, my computer is not starting instead it is displaying "cable not connected" and even i have replaced the display cable with the new one but no use at all. Can u please help me to solve this problem?
 

Read other answers
RELEVANCY SCORE 34.4

Hello, my name is gharib am from DAR ES SALAAM, TANZANIA. MY COMPUTER IS NOT TURNING ON FOR A MONTH NOW, I HAVE GIVE OUR LOCAL EXPERT AND HE SAID THERE IS PROBLEM WITH MOTHER BORD OF A LAPTOP AND IT HARD TO FIND AROUND IN MY CITY. CAN YOU DIRECT WHERE I CAN FIND AN EXPERT IN DAR ES SALAAM? MY WHTASAP NO. +255713668265

Read other answers
RELEVANCY SCORE 34.4

Hi everyone,

I have a PC with a MB Gigabyte GA-k8vm800m, I have 2 HD 80Gb Segate Barracuda. yesterday I have trouble rebooting this PC. It looks like it start it but it turn off after a few seconds no BIOS I can restart the PC with the Master Drive. but as soon as I plug the slave then it will not start. I try the slave drive in a different PC and I can see it just fine. So I do not understand what the problem is I changed cables. I put the slave on the IDE2 as master and slave and nothing. IS it the Motherboard IDE connector? Not enough power?
PLease if anyone have any ideas let me know.

AMD2800
 

A:hardware problem

Read other 9 answers
RELEVANCY SCORE 34.4

Dear sir
I have dell gx620 dual core system, I just update my BIOS for installing and when it again start, it start for few seconds than suddenly my power led become yellow color blinking and showing nothing on the screen.

Please guide me in this regard.
 

A:hardware problem

Read other 7 answers