Over 1 million tech questions and answers.

BSOD after installing Intel Graphics 3150 drivers, error 0x0000007f

Q: BSOD after installing Intel Graphics 3150 drivers, error 0x0000007f

Hello there,

I am new to the forums, so please excuse me for any rules I might break. I've read them all and as far as I know abide by them, but you never know.

The following problem is bothering me a lot:
Ever since my netbook crashed and I decided to reinstall Windows a week ago I am unable to install my video drivers: Intell Graphics Media Accelerator 3150. Whenever I do this (by using windows update or by downloading the drivers from ASUS) and I restart my netbook I get a blue screen with error 0x0000007f. When I look in the Event Viewer (after installing the driver via windows update I get the following errors:

EventID/Source
1001/BugCheck
41/Kernel-Power
6000/Winlogon
10005/DistributedCOM (four times)
7026/Service Control Manager

After installing the driver using the drivers from the ASUS website:
6008/EventLog
41/Kernel-Power
1101/EventLog
7001/Service Control Manager (eighteen times)
7026/Service Control Manager
1001/BugCheck
6000/WinLogon
10005/DistributedCOM (six times)

I fix this problem by going in to safe mode and uninstalling the same drivers again. After that I can restart Windows and everything is back to normal again.

System Specs:
Netbook ASUS 1005PE
Windows 7 Starter 32 bit
Reinstalled version of Windows 7 (not OEM anymore)
Processor: Intel Atom CPU N450 @1.66 Ghz (2CPUs)
Directx version: Directx 11
Memory: Kingston 800 Mhz 2 GB
Screen Resolution: 800 x 600 (should get bigger after installing video drivers)
System hardware approximately 3 years old

I am thinking about download the graphics drivers from the Intel site and try to install them. But, the fact that Intel is advising against that worries me.

Thanks for any help given!

Ronald

P.S. See attached file for BSOD Dump & System File Collection and the performance monitor report.

RELEVANCY SCORE 200
Preferred Solution: BSOD after installing Intel Graphics 3150 drivers, error 0x0000007f

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: BSOD after installing Intel Graphics 3150 drivers, error 0x0000007f

Very curious, in each and every crashdump the generic monitor driver showed up as the cause, and all from the same function (monitor!BrightnessTargetToPercentage+32), which is evident it's dealing with altering the brightness of the monitor, probably during a power-saving operation (like when the cable is unplugged or something else triggers the monitor to dim or brighten). I kinda wanna suspect that Windows didn't install great all the way.

If you want, you can go into device manager and go to your monitor and delete the driver for it. It should then automatically recover the driver from its local driver repository. Then, go to the Asus website and look for any updates for your chipset/motherboard/cpu drivers, as well as monitor, BIOS, and finally the graphics. Once you install the graphics drivers, hopefully it'll work this time.

If that doesn't work, you should run Disk Check (both options) followed by SFC Scan. Remember to run the SFC scan from whatever you used to install Windows (USB/DVD) by entering the Recovery Environment from there. Running it from the Recovery Environment hosted on your drive will not work.

If none of those comes up with anything, and you're still getting an issue when installing the graphics drivers, then I have to assume we're dealing with faulty hardware here. I mean, you did reinstall Windows because your system was crashing, so whatever was crashing it before the reinstall most likely is what is causing it now: hardware failure.

Read other 7 answers
RELEVANCY SCORE 89.6

Have been running Win10 on my little Samsung N145 laptot more or less as a test bed to see how well it can run on underpowered machines. I was in the insider programme so was running it on everything I could. Had this old laptot kicking around everyone had forgotten the password for so stuck it on here as well.

Had to install the 2GB memory before it would accept updates but it was plodding along quite successfully, if not quickly, until recently. Now running eval build 14931.

The login screen is now a block of white, any text is black squares.
The start menu looks like this:
and I can't get into the settings page through the button on the start menu. However, if I type control panel into search I can get into the old style no problem so it's something with the fancy win10 graphics and displays.

I know it's the GMA driver somehow, if I manually go into device manager and update the driver to the Microsoft basic display adapter it all works, I can see the start menu etc but I can't increase the resolution above 800x600.

Have tried the "latest" drivers off Intel's site. It doesn't list 10 as an OS option so tried the recommended Win7-64 drivers. Warning that they were older than what I had which I ignored but same outcome.

Is this as far as this laptot can go with Win10?

Read other answers
RELEVANCY SCORE 87.6

Hello All
I have a HP mini 210-1000 laptop that is currently running windows 7 with SP1 with no problems. According to the "Get Windows 10" program I cannot upgrade to windows 10 as the Intel Graphics Media Accelerator 3150 has a compatibility issue. Does anyone know if there are updated drivers? I have searched HP and Intel's website but could not find anything however I read on this forum where one person was able to install 10 on the HP with the atom processor and the Intel 3150 graphics without any issues.

Thanks in advance

Phil

A:Intel Graphics Media Accelerator 3150 incompatible with 10

I as well have read that this graphics card should be incompatible with Windows 10. If there is someone, who got it running, you might ask him on how he did it. It would be great, if you could report back the results!

However, the latest drivers for that card only support Windows 7 32 Bit. There already are no drivers for Windows 8 and 8.1 and Intel confirmed that there also will not be any drivers for Windows 10. I assume that - at least out of the box - this card will not work under Windows 10.

Read other 6 answers
RELEVANCY SCORE 74.8

I recently purchased a 250Gb Samsung 840 Evo for my desktop, for use as a system drive. I successfully installed Windows 7 x64, configured SATA mode and windows settings for the SSD, and went to install drivers (all current versions). After installing the Intel chipset driver, I attempted to install the USB 3.0 driver (included in the installation was the Intel USB 3.0 eXtensible Host driver and a few others). I immediately got a BSOD before the installation finished. It took a few tries to boot back up again, as I kept getting more BSODs on startup. Upon starting back up, my monitor resolution had jumped down a bit (but I could change it back), and the whole taskbar had disappeared. My desktop icons were present and working, and explorer.exe was running, but I could not get the taskbar to reappear, and the start menu and taskbar configuration settings would not open. At that point I just reinstalled windows, since I had no data on the drive yet.
 
After cloning the new installation, I attempted to install the drivers directly from the motherboard's installation disk, in case there were some issues with the new drivers, but the same BSOD issue continued to happen. So until I can figure this out, my USB 3.0 ports are running at USB 2.0 speeds. I never had this issue on my WD Caviar Black, though I haven't reinstalled Windows on it recently. Any help would be appreciated.
 
Motherboard is an ASrock B75M-DGS, CPU is an i5-3570k.

A:BSOD installing Intel USB 3.0 drivers

to the forum mate.
 
Please try the below steps.
 
Update system BIOS.
 
You can download the latest BIOS ( 1.30 ) from the below link. 
 
http://www.asrock.com/mb/download.asp?Model=B75M-DGS&o=All
 
Please update to it as it may contain bug fixes.
 
Disconnect any device connected to the USB 3.0 port and make sure everything is connected to the 2.0 ports. Now download and install the latest driver from the below link.
 
https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=21129
 
 
Report whether it helps you.

Read other 3 answers
RELEVANCY SCORE 74

I recently attempted to install the Intel eXistensible USB 3.0 driver as I was having BSOD issues when trying to install a new version of some audio software (Scarlett Mix Control). Installing the Intel driver also resulted in a BSOD though.

It has been brought to my attention that the original BSOD issues caused iusb3xhc.sys, which is why I tried installing the USB 3.0 drivers.

My PC also has an unresolved issue of hanging at the 'Shutting Down' screen, if I have put the computer to sleep and woken it up prior to shutting down (if I have not put the PC to sleep it shuts down fine).

If left hanging for long enough, a BSOD occurs.

Attached is the minidumb and DxDiag.

A:BSOD when installing Intel drivers and when shutting down

BSOD analysis and minidump attached

Read other 19 answers
RELEVANCY SCORE 74

Hi! I'm trying to update intel graphic card driver. When I run the installer this is the error message:Error?I'm downloading the driver update from the support lenovo page. I've succesfully updated NVidia driver from the same site. In support page, I used Lenovo Bridge to detect my computer, so it must be compatible. My computer is a Lenovo Yoga 700-14ISK model 80QD.Thanks for helping me!

Read other answers
RELEVANCY SCORE 73.6

Hello guys,

Recently my laptop (Asus X550L, Windows 10) was getting an annoying error on my Intel graphics. It will hang up a bit then display a prompt that my "graphic stopped working and was recovered." It happens when I'm playing some videos on Youtube or playing games. I also notice that the applications I setup to run on my GT840m won't run on it, instead, it will use the onboard graphics.

Below are the things I tried:
1. Update my intel driver using windows update. After download and installation, on the end, it says, "illegal operation attempted on a registry key marked for deletion". Also tried downloading driver on their website but it also fails to install.
2. Removed the driver then tried to re-install it using windows update and downloaded driver. Same happens above. But now the working graphics is my discrete (GT 840M).
3. I also tried to update/re-install the driver on Safe Mode, same result.
4. Tried to look some answers regarding the error on no. 1 in connection with driver installations but I did not find anything on the internet.

Here are my basic laptop specs:
Intel i7-4500u
Intel Graphics Display 4400
Nvidia GeForce 840M
8Gb Ram

I'm out of ideas so I'm hoping that anyone can help me here. Thanks!

Read other answers
RELEVANCY SCORE 73.2

When i extract the setup and execute installer it states that your system does not meet minimum requirements.
But i used this driver well in Windows 7 64bit
My laptop is Samsung 350V4X-SOCTH. And i am sure it meets all the requirements

A:Error while installing intel 4000 hd drivers.

You might need to download the latest driver that supports Windows 8/8.1 here : Intel HD Graphics 4000

Read other 3 answers
RELEVANCY SCORE 71.6

After installing the drivers for my ATI Radeon HD 6450,I am asked to restart my computer. Every time I just get a blue screen on startup and have to restore from backup. I've attached a zip file of the logs from the BSOD.

A:BSOD After installing graphics drivers

Hi 17hoehbr.

It is a very old branded desktop, and a stop 0x116 may occur on it due to various reasons.

First, the GPU itself. You said that it is an ATI Radeon HD 6450; but it is not active when you executed the DM Log Collector. We are getting the GPU info is ....

Code:
Card name: Standard VGA Graphics Adapter
Manufacturer: (Standard display types)
Chip type: AMD ATOMBIOS
May be the GPU is corrupt itself. As a test, get any other GPU, from friends or family. Apply it and observe it it is producing the same BSOD or not. It seems that without the GPU, the computer works fine. We need to know that if it is the particular GPU, or any other GPU.

Some other info are very much needed to know, depending on the age and the build of the computer.

Check if the Power Supply Unit (PSU) supplying adequate power to the computer or not.
eXtreme Power Supply Calculator
Also let us know the wattage of the PSU.

Is the computer hot? Report us the heat of the computer after a couple of hours of your normal usage. Upload a screenshot of the summery tab of Speccy. Alternatively, you can publish a Speccy snapshot too: Speccy - Publish Snapshot of your System Specs .

Let us know the results.
____________________________

Code:
*******************************************************************************
* *
* Bugcheck Analysis ... Read more

Read other 1 answers
RELEVANCY SCORE 71.6

Hello,

I was minding my own business, installing Catalyst drivers for my ATI Radeon HD 5450. The installer was checking graphics hardware, but then the screen turned black, and I got a BSOD saying, "Plug and Play detected an error most likely caused by a faulty driver." This happens every time I try to install new drivers for my GPU. What can I do about it?

- That PlaneFreak

A:BSOD while installing graphics drivers

First of all, do you have a compelling reason for updating the graphics driver, or is it just that you believe you must always install the latest driver?

The golden rule with drivers is, if the current driver is working okay you leave it alone.
Only update a driver if the existing one is giving you a problem and you know that the new version will fix it.

So unless you are having problems with the old driver, keep it. Updating drivers is not compulsory or even desirable (as you've just discovered).

Read other 2 answers
RELEVANCY SCORE 71.6

Hi,

The problem I'm having right now is the fact that last night my computer decided to just shut itself down randomly after me starting up World of Warcraft. Afterwards it would only give me BSOD's with BCCode 116. As it had been some time since a fresh install (over a year probably) I figured this would be a good opportunity to go for one now.
After reinstalling Windows 7 Ultimate (64 bits) I moved on to install all my drivers/virus scanner/etc. and everything seemed to be back to normal. After turning my computer back on the next morning it still booted up fine and without any issues allowed me to send a few e-mails. After this I decided to play some Dark Souls 2. Before even getting into the game my computer gave me a BSOD and did nothing other than that.

I moved on as follows: I reinstalled Windows again because, when in doubt reinstall (as it's the easiest and least time consuming). Afterwards I installed my graphics driver. As BCCode 116 has something to do with the graphics card or the graphics drivers (according to my googling skills) I assumed I'd save time by installing those first.

This unfortunately did not help. When running with ANY kind of official Nvidia GeForce drivers my computer just keeps throwing BSOD's at me with the same 116 code in it.

I've tried installing older drivers, newer drivers, I've even tried installing the same drivers I've been using for the past 2-3 months but none seem to work.
In one of the posts I found it was mentioned that thi... Read more

A:BSOD after installing Graphics Drivers

Well the latest versions of Nvidia graphics drivers appear to be quite unstable in a lot of cases.
Can you remove your graphics drivers and install the version 314.22.

Here's some instructions to help you out.

NVIDIA Drivers - Avoid Problems


Code:
fffff880`0327e000 fffff880`03ed6000 nvlddmkm T (no symbols)
Loaded symbol image file: nvlddmkm.sys
Image path: \SystemRoot\system32\DRIVERS\nvlddmkm.sys
Image name: nvlddmkm.sys
Timestamp: Tue Mar 04 11:07:52 2014 (5315B408)
CheckSum: 00C20523
ImageSize: 00C58000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
I also recommend running a hardware test on your GPU.
Stress test your graphics card with Furmark

I recommend running it for around 30 minutes



   Warning

Furmark will increase the temperature of your GPU rapidly so keep and eye on your temperatures

Post back the results.

Read other 9 answers
RELEVANCY SCORE 70.8

I recently got a mint condition XFX 6950 2GB from ebay. The card looks great but apparently had many software issues. First, I couldn't install any of the AMD drivers without getting the BSOD related to atikmpag.sys. I fixed the problem by doing the whole expand the AMD files and moving them to system32. The next problem I faced is drivers and artifacting. There are white lines running down my screen. Although the BSOD is now gone, the AMD drivers don't load and say that the drivers have improperly been installed on the system. I have installed drivers atleast 6 times and installed all the WHQL versions. I have no idea what to do anymore and any help is appreciated. Also, I have the lated Direct X as well as the latest .net framework. Thanks in advance.

Read other answers
RELEVANCY SCORE 70.8

I'm amid a bit of a crisis and seek help.

A few days ago, I got these weird hangs of sorts where it would make any sounds currently playing as audible as a crappy dubstep song. It would then freeze and after awhile everything would stabilize and I'd get this bubble


It would happen once or twice between 5 days ago and 2 days ago, didn't think a ton of it and downloaded the latest video drivers but they wouldn't install.

The next day, I start up and get a BSOD with an error along the lines of "an attempt to reset the display driver and recover from timeout failed" and this perpetuates every time I boot up normally WITH MY GRAPHICS DRIVERS INSTALLED.

I repeat, I can start up "fine" in:
1: Safe-but-do-nothing mode
2: Normally with the graphics drivers uninstalled.

This weirdly enough happened after I took my graphics card out to clean it, but I handled it carefully and to my knowledge nothing broke. However, It seems the issue has been isolated to there, as the BSOD also warns to "uninstall or disable any hardware or software recently installed". Obviously it could consider a recent install what was really just putting the card back in.

I have an MSI 9800 GT that is pushing 3 years old, is it surprising if this thing's KIA after daily use for that long?

Also I see this blue screen precisely, except for the error codes preceded by "STOP" and the crap just below that is different too.

http://h30434.www3.hp.com/t5/... Read more

A:[SOLVED] BSOD upon installing graphics drivers

Hi,

When you're getting these messages, it's means something is faulting the display driver - but it can successfully recover from its timed out state. However, if for whatever reason it cannot recover from its timed out state, you will then experience a BSOD... specifically a 116 code. Some info regarding 116 bugchecks:

The following hardware issues can cause a TDR event:


Quote:




1. Unstable overclock (CPU, GPU, etc). Revert all and any overclocks to stock settings.

2. Bad sector in memory resulting in corrupt data being communicated between the GPU and the system (video memory otherwise known as VRAM or physical memory otherwise known as RAM).

GPU testing: Furmark

RAM testing: Memtest86+

3. Corrupt hard drive or Windows install / OS install resulting in corruption to the registry or page file.

HDD diagnostics: Hard Drive Diagnostic Procedure

To reset your page file, follow the instructions below:

a ) Go to Start...Run...and type in "sysdm.cpl" (without the quotes) and press Enter.

-Then click on the Advanced tab,
-then on the Performance Settings Button,
-then on the next Advanced tab,
-then on the Virtual Memory Change button.

b ) In this window, note down the current settings for your pagefile (so you can restore them later on).

-Then click on the "No paging file" radio button, and
- then on the "Set" button. Be sure, if you have multiple hard drives, that you ensure that the paging file is set to 0 on ... Read more

Read other 15 answers
RELEVANCY SCORE 70

Here are my specs:
CPU: Intel® Core™ i5-6600K 3.50GHz 6MB Intel Smart Cache LGA1151 (Skylake)
MEMORY: 8GB (4GBx2) DDR4/2800MHz Dual Channel Memory (ADATA XPG Z1)
MOTHERBOARD: GIGABYTE G1.Sniper Z170 SLI ATX w/ USB 3.1, 3 PCIe x16, 2
PCIe x1, 3 SATA Express, 6 SATA3, 1 Ultra M.2
OS: Windows 10 Home (64-bit Edition)
POWERSUPPLY: 750 Watts - EVGA SuperNOVA 750 G1 80 PLUS Gold Power Supply
VIDEO: AMD Radeon R9 390X 8GB GDDR5 PCIe 3.0 x16 Video Card 
 
I recently bought a PC from CyberPower PC and everything seems fine except for the graphics card. When I first connected it there were green bars and horizontal lines on the screen so I checked to see if it was seated properly but then after reconnecting it I would just get black screen (No Signal). Tried a clean install of drivers by booting into safe mode and using DDU by Guru3D to remove the AMD graphics drivers then rebooting and installing the drivers from the AMD website. It gets past the installer download (Catalyst and Crimson tried both) but as soon as it hits installing Display Driver it always hangs for a sec then BSOD, same thing when trying to install the windows update for r9 390 devices. Just incase I also ran memtest and got no errors. Is it possibly just a faulty graphics card?
 
Here's what I got from the dump file analysis.

Spoiler

 
Microsoft ® Windows Debugger Version 10.0.10586.567 X86
Copyright © Microsoft Corporation. All rights reserved.
 
 
Loading Dump ... Read more

Read other answers
RELEVANCY SCORE 70

I have a Windows 8.1 system running a Haswell Intel Core i3 and an Asrock H88 motherboard hooked up to a Samsung HDTV.

No matter which vendor's video card I use, installing graphics drivers will cause it to crash back to the start screen. There's no BSOD or any indication Windows realized a crash occurred, it just boots me back to the desktop.

This has occurred with the Intel integrated graphics, two nvidia cards (750ti and 970 gtx), and one AMD card (R7 260x). It happens everytime I attempt to install a graphics driver. Certain features of the graphics driver (ie, enabling/disabling stereoscopic 3d) will also cause the crash.

If I reboot into safe mode, I can install the graphics drivers. Then the system will boot up and proceed to crash to the desktop after several log in attempts, before finally settling with the graphics drivers apparently installed. Generally, all graphics driver settings will be reset when this happens.

I've tried various driver cleaning tools to remove all trashes of existing drivers, but the issue still occurs.

Read other answers
RELEVANCY SCORE 69.6

I cannot find any solutions to similar problems on the internet. I replaced a broken lcd screen with a new lcd of the same brand for netbook Asus EeePC 1001P. As soon as I install Intel Graphics Media Accelerator 3150 I received BSOD. BSOD occurs soon after desktop starts to load. I do not not think it's a hardware problem (i.e. motherboard or graphics card), because there are no problems with screen display at full 1024x600 resolution on a freshly installed XP or Mint linux on the same netbook. I've tried the most current Intel drivers and earlier versions, but they all cause BSOD. I've tried disabling most of the other hardware, but have yet to find any that maybe causing conflict with the graphics driver. Dump file say the cause of BSOD is monitor.sys. I've even tried replacing monitor.sys from a working Windows 7, but same error occurs on the netbook. I've attached the SF Diagnostic Tools logs. Thank you for your time. I eagerly await your suggestions.

A:BSOD UNEXPECTED_KERNEL_MODE_TRAP 0x0000007f after graphics driver

Hi,
Your crashes were caused by the generic monitor.sys which Windows loads for your monitor, and it seems to be related to the brightness calculation causing a EXCEPTION_DIVIDED_BY_ZERO fault.


Code:

*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
Use !analyze -v to get detailed debugging information.
BugCheck 7F, {0, 0, 0, 0}
Probably caused by : monitor.sys ( monitor!BrightnessTargetToPercentage+32 )
Followup: MachineOwner
---------
0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
UNEXPECTED_KERNEL_MODE_TRAP (7f)
STOP 0x0000007F: UNEXPECTED_KERNEL_MODE_TRAP

Usual causes: Memory corruption, Hardware (memory in particular), Overclocking failure, Installing a faulty or mismatched hardware (especially memory) or a failure after installing it, 3rd party fi... Read more

Read other 9 answers
RELEVANCY SCORE 68.8

4Hey guys!
My netbook(Samsung NC110 with 1024*600 Screen Resolution and Intel GMA 3150) is running Win8.1 x64 now. I want to use all features of Win8, so i want to set Custom resoltion like 1366*768. I was trying to change some keys in the regedit, but the picture was very bad, cause my screen is 16:9, and 1024*768 or 1152*864 resolutions is 4:3
I want to get some utility to set Custom Resolutions, that bigger that real resolution of my display
p/s/Sorry for my bad english, Hi from Ukraine!

A:Intel GMA 3150+Custom screen resolution

i don't think it can be done
even if you can set to 1366*768 it will looks weird :s

Read other 4 answers
RELEVANCY SCORE 68.4

Today,while watching a video my Lenovo laptop (20236 serial number) it just blue screened.I didnt get to read a lot of it because it restarted my laptop very quickly but i managed to get a app thing that was able to read the dump file.In the Device Manager i realised the error was from my Intel HD Graphics 4000 driver.I went online and reinstalled it.After the first bluescreen no more blue screens happend but my windows seem to have a weird trail behind them when i move them over anything(icons on the desktop/other windows)
and anywhere i go watch videos they seem to lag(i thought it was a refresh rate or frame rate issue from the graphics driver).I pretty much can see the line in the middle of the screen where the pixels are changing between frames.After reading the dump file i got this information:
                    -Bug Check String: MEMORY_MANAGEMENT
                    -Bug Check Code: 0x0000001a
                    -Parameter 1: 0x00041790
                    -Parameter 2: 0xc08020da
                    -Parameter 3: 0x0000ffff
                    -Parameter 4: 0x00000000
                    -Caused by dr... Read more

A:BSOD issue/graphics driver error Intel

halmacpi.dll is also highlighted in red

Read other 1 answers
RELEVANCY SCORE 68

Hello,
 
I'm afraid I have run out of ideas trying to fix this issue. Hopefully you can help me find a solution
 
The problem started when I was invited to play the game Rift with friends. I installed the client, it complained about a number of things (my computer is old and not that powerful by today's standard), one of them was that my video drivers were too old. So I downloaded the latest drivers at the time (327.23, video card is GeForce 9600 GT) and installed them. When I rebooted, I got a BSOD on system startup (immediately after the Windows XP logo with the loading bar disappeared)
 
That was about 3 weeks ago. At the time, I solved the problem by loading in safe mode, uninstalling the driver, and reinstalling the one I had before (266.58). The system successfully loaded, I decided I could stick with the old driver, and moved on
 
I don't think I rebooted the system between then and today - usually I only send the computer to sleep. Today, I installed new Windows updates, and obviously it asked me to reboot after that. Once again, I got a BSOD on system startup - this time with the old version of the drivers
 
I went to safe mode and uninstalled the video driver again. The system loaded without them. I went to Nvidia site and used the smart search to be sure I choose the right driver. I installed the on it recommended (version 332.21) and tried to start the system. BSOD again. All attempts to make the video card work gave the same res... Read more

A:BSOD after updating Nvidia drivers - STOP 0x0000007F

The first two minidumps relate to Trusteer Rapport and the second two are related to your Norton Security. Did you recently install either of these?

Read other 3 answers
RELEVANCY SCORE 64

So, like the title says, I installed a new graphics card (MSI N670 PE 2GD5/OC) and since then my computer has been very unstable and is crashing a lot. The card is factory overclocked and I think it is faulty. Do you know of a way to underclock the card, so I can test if it is the overclock?


PSU: Enermax EMG700AWT

*edit*

So I used Afterburner to set my core clock to -104 and my power limit to 72% and this causes my card to boost to about 980MHz. With these settings the crashing has stopped. So the card cannot be used with the factory OC settings. So should I RMA?

A:BSOD after installing new Graphics Card, error 0x000000101

Hello theone320.

► As far as I am seeing, you are not overclocking.

Code:
kd> !sysinfo cpuspeed
CPUID: "Intel(R) Core(TM) i7 CPU 920 @ 2.67GHz"
MaxSpeed: 2670
CurrentSpeed: 2666
► Your dumps say stop 0x101, hardware related. Mostly CPU is the guilty for it.
Hardware - Stress Test With Prime95

► Test the graphics card, too!
Video Card - Stress Test with Furmark

► Another one generates 0x9C, which is just similar to 0x124.
Follow the suggestions, thoroughly: Stop 0x124 - what it means and what to try

► Are you still using IE8? Better you shift to IE9.

▼ But, the first option would be, ask the vendor to check the graphics card, and if it is faulty, get a replacement.

Read other 3 answers
RELEVANCY SCORE 64

Hi,

I hope to resolve my problem, numark can't BTW...

I attached the zip file...

So, when i try to install the drivers for the numark soundcard dj io i get a BSOD with the 0x000000b8 error the only time that i manage to install it was when i boot from a safe mode but even then when i try to use it in normal mode a get also a BSOD...

My laptop is a Dell Inspiron 5520 with :

Chipset : Intel HM 77
Processor : Intel i5-3210
Video : Intel HD 4000 & AMD HD 7670M
RAM : 6 GB
Connections : 4 X USB3


Please heeeeeelp me...

A:BSOD when installing drivers for DJ IO, error 0x000000b8

here are some images

Read other 3 answers
RELEVANCY SCORE 64

I have received multiple BSOD's while attempting to get my new rig up and running. I formatted my old hard drive that had my old windows on it and installed windows on a new solid state. It still prompts me to pick from two windows 7's upon start-up.

Any help is greatly appreciated!

A:BSOD just installing drivers, error 124. New Computer

Is the old hard drive still attached when you boot Windows? If so, disconnect it - if I am correct, it should not boot. If it doesn't boot up, reconnect the old hard drive again and boot again, then post back here.

Read other 7 answers
RELEVANCY SCORE 63.6

Hi everyone, I've been experiencing the BSOD on my new HP dv6 laptop for all 3-4 months I've had it. Here are the specs:

Windows 7, 64 bit, came installed on laptop, have not tried a clean install yet (hopefully won't have to), Intel Core i7 CPU Q720 @ 160 GHz, video card is a NVIDIA GeForce GT 320M

I'm getting a BSOD STOP 0x0000007F (0x0000000000000008, 0x0000000080050033, 0x00000000000006E8, 0xFFFFF800030A0EC0).

There doesn't seem to be a pattern to them, sometimes the laptop runs for hours and is fine other times I can turn it on a get a BSOD in 5 min. I also have Zonealarm and AVG Anti virus if those are possible causes.

I'm stumped/frustrated and would greatly appreciate some help. Thanks in advance.

A:BSOD 0x0000007F error

Remove ZoneAlarm for the time being. Here's the official removal tool: http://forums.zonealarm.com/showpost...53&postcount=3

Run this free diagnostic on your hard drive: http://www.carrona.org/hddiag.html (read the details at the link)

Then update all of your drivers from the HP website (HP's tend to have a lot of older drivers installed when leaving the factory).

Then, please run Driver Verifier according to these instructions:

Quote:




Using Driver Verifier is an iffy proposition. Most times it'll crash and it'll tell you what the driver is. But sometimes it'll crash and won't tell you the driver. Other times it'll crash before you can log in to Windows. If you can't get to Safe Mode, then you'll have to resort to offline editing of the registry to disable Driver Verifier.

So, I'd suggest that you first backup your stuff and then make sure you've got access to another computer so you can contact us if problems arise. Then make a System Restore point (so you can restore the system using the Vista/Win7 Startup Repair feature).

Then, here's the procedure:
- Go to Start and type in "verifier" (without the quotes) and press Enter
- Select "Create custom settings (for code developers)" and click "Next"
- Select "Select individual settings from a full list" and click "Next"
- Select everything EXCEPT FOR "Low Resource Simulation" and click "Next"
NOTE: You can... Read more

Read other 1 answers
RELEVANCY SCORE 63.6

After rebooting i get a BSOD about 5 min while the desktop is loading

error code is STOP: 0000007F (0x00000008, 0x8B74A130, 0x00000000, 0x00000000)

I can still operate in safe mode but not safe mode with networking
 

A:BSOD 0x0000007f error

"I can still operate in safe mode but not safe mode with networking"...

This tells us that is is a driver issue, possibly dealing with the network driver. Are there any BSOD's to attach here, and what are your complete system specs and what version of Windows are you running? Go here and learn how to find and attach any minidumps:
http://www.techspot.com/vb/topic51365.html
 

Read other 4 answers
RELEVANCY SCORE 63.6

Scince Feb have been getting BSOD errors with various stop codes mainly apc-index-mismatch. Suggestions on net indicated memory failure so ran memtest86 and sure enough all tests failed. Replaced original 2x1mb with 2x2mb again ran memtest and all tests OK.

System

Advent 8212 notebook (new May 2008)
Intel Core 2 Duo
Intel 965 GM video
Windows 7 (new install Sept 2009)
Ram now 4mb with 3mb available

Net seemed to suggest problem with video drivers so disabled but no difference. Do not seem to get bsod in safe mode with networking so am assuming (and hoping) driver problem and not motherboard.

Have run windows essentials and machine is clean

Minidump files can be viewed at http://cid-36e2e494e7fe5e85.skydrive.live.com/browse.aspx/Minidump
Any suggestions please as its driving me nuts

Thanks in advance

Keith
 

A:BSOD error 0x0000007f

Read other 15 answers
RELEVANCY SCORE 63.6

Hi, I've been getting BSODs for the past couple of months. I'm running Windows 7 Professional x64 on a one-year-old Sony Vaio VPCS12C7E laptop. It's the original OS which came installed on the system, and I've never re-installed it.

The BSODs all share some basic features:

They're all 0x0000007f UNEXPECTED_KERNEL_MODE_TRAP errors (see attached dump files).
They all happen when watching content online (usually Adobe Flash based, such as YouTube) though occasionally offline when using VLC player.
They all happen seemingly sporadicly - either thirty seconds or two hours under the above conditions.
The BSODs also occur more instantaneously when streaming high-quality videos or multiple files at once.

They started happening directly after I inserted an empty USB memory stick from a friend into my laptop. I can't recall the make or model of the USB stick off the top of my head, but it might have been the cause or simply a coincidence - I've not been able to get my head around it.

Anyway, here are the dump files - thank you so much for your efforts.

A:BSOD error 0x0000007f

Hello woopington & Welcome to SevenForums!

Type "devmgmt.msc" (without quotes) in your Start Orb.

Post a snapshot of it, and post it (How to post pic on SF)

Summary

Code:
CUSTOMER_CRASH_COUNT: 1

DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT

BUGCHECK_STR: 0xFE

PROCESS_NAME: System

CURRENT_IRQL: 0

LAST_CONTROL_TRANSFER: from fffff880068b99ec to fffff800030d55c0

STACK_TEXT:
fffff880`035b6c18 fffff880`068b99ec : 00000000`000000fe 00000000`00000008 00000000`00000006 00000000`00000005 : nt!KeBugCheckEx
fffff880`035b6c20 fffff800`033ce973 : fffffa80`09a4f050 fffff880`0b1d20f0 ffffffff`dc3a58a0 fffff800`0327a5f8 : usbhub!UsbhHubProcessChangeWorker+0xec
fffff880`035b6c80 fffff800`030e27e1 : fffff880`0b1cba00 fffff880`0b1cbaf0 fffffa80`0545eb60 00000000`00000000 : nt!IopProcessWorkItem+0x23
fffff880`035b6cb0 fffff800`033756fa : 2e777777`2e666163 fffffa80`0545eb60 00000000`00000080 fffffa80`053cb9e0 : nt!ExpWorkerThread+0x111
fffff880`035b6d40 fffff800`030b3b46 : fffff880`033d5180 fffffa80`0545eb60 fffff880`033dffc0 37373432`33323d64 : nt!PspSystemThreadStartup+0x5a
fffff880`035b6d80 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiStartSystemThread+0x16
STACK_COMMAND: kb

FOLLOWUP_IP:
usbhub!UsbhHubProcessChangeWorker+ec
fffff880`068b99ec cc int 3

SYMBOL_STACK_INDEX: 1

SYMBOL_NAME: usbhub!UsbhHubProcessChangeWorker+ec

FOLLOWUP_NAME: MachineOwner

MODULE_NAME: usbhub

IMAGE_NAME: us... Read more

Read other 3 answers
RELEVANCY SCORE 63.2

hello guys , new here ... i want to update my drivers but i cant like my intel hd graphics driver

Laptop: Toshiba c660 satellite
Windows 8.1 pro 64 bit
4gb ram
intel core i3 370m 1st gen
intel hd 8.15.10.2900

problem is that i dont know whats version of my intel hd graphics generation like 1000/2000/3000 etc,..

or is it a gma hd?

how to identify>?

Intel? HD Graphics (Core i3)


Report Date: 10/17/2015
Report Time[hr:mm:ss]: 13:35:17
Driver Version: 8.15.10.2900
Operating System: (6.2.9200)
Default Language: English (United States)
DirectX* Version: 10.1
Physical Memory: 2919 MB
Minimum Graphics Memory: 32 MB
Maximum Graphics Memory: 1523 MB
Graphics Memory in Use: 90 MB
Processor: Intel64 Family 6 Model 37 Stepping 5
Processor Speed: 2394 MHz
Vendor ID: 8086
Device ID: 0046
Device Revision: 02


* Accelerator Information *


Accelerator in Use: Intel(R) HD Graphics
Video BIOS: 1994.0
Current Graphics Mode: 1366 by 768


* Devices Connected to the Graphics Accelerator *


Active Notebook Displays: 1
* Built-in Display *


Monitor Name: Generic PnP Monitor
Display Type: Digital
Gamma Value: 3.55
DDC2 Protocol: Supported


Maximum Image Size:
Horizontal: 11.42 inches
Vertical: 06.30 inches


Monitor Supported Modes:
1366 by 768 (40 Hz)
1366 by 768 (60 Hz)


Display Power Management Support:
Standby Mode: Not Supported
Suspend Mode: Not Supported
Active Off Mode: Supported


Raw EDID:
00 F... Read more

A:Intel HD Graphics, help for drivers

https://downloadcenter.intel.com/dow...Update-Utility

Read other 2 answers
RELEVANCY SCORE 63.2

My system has Windows XP Sp3 installed.

My video card is an Nvidia Geforce 9800 GTX.

I have no BSOD or problems whatsoever. I noticed there were new drivers so I went to download them.

I installed the new drivers and upon restart got BSOD at the windows loading screen involving "nv4_disp.dll". I believe it was 0x00000050.
Anyway, I didn't install the new driver in safe mode, nor with antivirus disabled. Would this cause the problems?

I rolled back the driver and no more BSOD.

The only reason I wanted the new driver is because I was hoping they fixed it in the nvidia control panel so you could select "dual view" with 2 monitors, instead of only "clone" view being available.

Thanks
 

A:BSOD nv4_disp.dll error after installing new NVIDIA drivers

you can try uninstalling the driver you have now and then installing the new one.Just make sure you know what version you have now. Just incase you have to revert back.
You should always uninstall a driver before installing a new one.
 

Read other 1 answers
RELEVANCY SCORE 63.2

Original title: The computer has rebooted from a bugcheck. The bugcheck was: 0x0000007f (0x0000000000000008, 0x0000000080050033, 0x00000000000406f8, 0xfffff88004f7a1ed).

hi all!

Been getting a lot BSOD?s in the past few days. All my drivers and bios are up to date. Yesterday the same BSOD happened 10 times.

Anybody got ideas?
I Downloaded the Diagnostics tools of SevenForums and followed the steps: I attached the results of Diagnostic tools here.
Thank you all!
Juan.

A:BSOD error: The bugcheck was: 0x0000007f

There are a lot of causes of a STOP 0x0000007F: UNEXPECTED_KERNEL_MODE_TRAP

Usual causes: Memory corruption, Hardware (memory in particular), Overclocking failure, Installing a faulty or mismatched hardware (especially memory) or a failure after installing it, 3rd party firewall, Device drivers, SCSI/network/BIOS updates needed, Improperly seated cards, Incompatible storage devices, Overclocking, Virus scanner, Backup tool, Bad motherboard, Missing Service Pack.

First, I would say if you are overclocking any hardware, please stop.

Make scans with the following:

Kaspersky TDSSKiller - TDSSKiller Rootkit Removal Utility Free Download | Kaspersky Lab US

ESET online scanner - Online Virus Scanner Eset

Zone Alarm Firewall is also a possible cause of your BSOD's.

Code:
fffff880`0c80c588 fffff880`051a49f2 igdkmd64+0x2c09f2
fffff880`0c80c590 00000000`00000000
fffff880`0c80c598 fffff880`0467dcd1Unable to load image \SystemRoot\system32\DRIVERS\vsdatant.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for vsdatant.sys
*** ERROR: Module load completed but symbols could not be loaded for vsdatant.sys
vsdatant+0xacd1
fffff880`0c80c5a8 fffff880`046d6500 vsdatant+0x63500
fffff880`0c80c5b0 fffff880`0c80c5e0
fffff880`0c80c5b8 fffff880`051a3fdf igdkmd64+0x2bffdf
fffff880`0c80c5d8 fffff880`0467dcd1 vsdatant+0xacd1
fffff880`0c80c5e0 fffff880`0c80c610
fffff880`0c80c5e8 fffff880`050f7912 igdkmd64+0x213912
fffff880`0c80c618 fffff880`04f1f95c igdkmd64+0x3b95c
Unin... Read more

Read other 5 answers
RELEVANCY SCORE 63.2

Hi,
 
Around two months ago I started getting blue screen crash dumps shortly after Windows started, every time without exception (almost always within a few minutes or less). I don't remember installing any new software around this time and it seemed to have started out of nowhere (though if it were a software problem it may have to do with some kind of incompatible software update). I don't get the errors when running in safe mode or safe mode with networking. I am sick of being stuck in safe mode so thank you for any help you can provide!
 
Some basic info about my PC:
 
Model: HP/Compaq nc8430
Operating system: Windows 7 Professional 32-bit with Service Pack 1
RAM: 4 GB
Processor: Intel Core 2 T5600 @ 1.83 GHz
Peripherals: Microsoft Wireless Mobile Mouse 4000
 
The error code is as follows:
 
*** STOP: 0x0000007F (0x00000008, 0x801E1000, 0x00000000, 0x00000000)
 
Here is the log generated by Bluescreenview:
 
==================================================
Dump File         : 020813-51199-01.dmp
Crash Time        : 2/8/2013 12:47:49 AM
Bug Check String  : DRIVER_POWER_STATE_FAILURE
Bug Check Code    : 0x0000009f
Parameter 1       : 0x00000004
Parameter 2       : 0x00000258
Parameter 3       : 0x84c96020
Parameter 4       : ... Read more

A:BSOD Stop Error 0x0000007F

I should add:
 
I have also run a Windows memory diagnostic and no errors were found.
 
I'm running McAfee Internet Security (I've read that similar errors were found to be caused by Symantec/Norton security software). Real-time scanning is disabled in safe mode. However, I still get the errors when I disable real-time scanning in normal mode as well as when the mouse dongle is unplugged.

Read other 14 answers
RELEVANCY SCORE 63.2

Hi,
 
Hope you're well.
 
I keep getting a BSOD in both windows 10 and windows 7. I have recently installed windows 7 and have received and error code:
0x0000007F (0x00000000000000010,0x0000000080050033,0x00000000000406F8,0xFFFFF80002cc9342) 
 
In event view viewer an error has occurred:
 
The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID 
{9BA05972-F6A8-11CF-A442-00A0C90A8F39}
 and APPID 
{9BA05972-F6A8-11CF-A442-00A0C90A8F39}
 to the user kevin-PC\kevin SID (S-1-5-21-79585836-2096477218-3416894218-1000) from address LocalHost (Using LRPC). This security permission can be modified using the Component Services administrative tool.
 
My Specs:
Tntel 2500k
Corsair 12gb ram 1600
Asus Extreme 4 gen3
gtx 970 
Corsair 650w psu
SSD Evo 850
 
Regards,
Kevin 

A:BSOD Error code 0x0000007F

Hi,
 
Hope you're well.
 
I keep getting a BSOD in both windows 10 and windows 7. I have recently installed windows 7 and have received and error code:
0x0000007F (0x00000000000000010,0x0000000080050033,0x00000000000406F8,0xFFFFF80002cc9342) 
 
In event view viewer an error has occurred:
 
The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID 
{9BA05972-F6A8-11CF-A442-00A0C90A8F39}
 and APPID 
{9BA05972-F6A8-11CF-A442-00A0C90A8F39}
 to the user kevin-PC\kevin SID (S-1-5-21-79585836-2096477218-3416894218-1000) from address LocalHost (Using LRPC). This security permission can be modified using the Component Services administrative tool.
 
My Specs:
Tntel 2500k
Corsair 12gb ram 1600
Asus Extreme 4 gen3
gtx 970 
Corsair 650w psu
SSD Evo 850
 
Regards,
Kevin 
Hi
I can't seems to find your dump files in your filecollector. Thus unable to analyze. 
Please re-upload again.
Thanks.

Read other 1 answers
RELEVANCY SCORE 63.2

Today as usually i started my PC.
But BSOD appeared:s
I had problems with AVG last week and solved them so PC worked perfecly from then!
Error code: 0x0000007F
I bought Windows and i had to delete it i had to pay again
 

Read other answers
RELEVANCY SCORE 63.2

About 3 weeks ago, I started getting BSOD's alot, I tried re-installing windows 7, that didn't fix the problem.

BSOD usually comes when I am playing league of legends or even just browsing web, or not even at the computer.

I attached the dump files below.


- hp pavilion dv6700 laptop
- x86 (32-bit)
- upgraded from vista to W7 professional 6 months ago
- What is the age of system (hardware)? system is 3 years old
- Have had W7 pro installed for 2 weeks

A:BSOD - ntkrnlpa.exe - error 0x0000007f

  
Quote: Originally Posted by KYTNZ


About 3 weeks ago, I started getting BSOD's alot, I tried re-installing windows 7, that didn't fix the problem.

BSOD usually comes when I am playing league of legends or even just browsing web, or not even at the computer.

I attached the dump files below.
- hp pavilion dv6700 laptop
- x86 (32-bit)
- upgraded from vista to W7 professional 6 months ago
- What is the age of system (hardware)? system is 3 years old
- Have had W7 pro installed for 2 weeks



That Bugcheck on 32 bit is usually because of zone alarm. If so remove it. If not you have several old drivers all of which need up dating.

STOP 0x7F (UNEXPECTED_KERNEL_MODE_TRAP)

Old drivers

Code:
rixdptsk.sys 11/14/2006 9:35:19 PM 0x92aa9000 0x92afa000 0x00051000 0x455a6ed7
HpqRemHid.sys 7/11/2007 11:30:21 AM 0x92afa000 0x92afbc00 0x00001c00 0x4694f78d
smserial.sys 9/26/2008 4:23:38 AM 0x90c7c000 0x90d90000 0x00114000 0x48dc9c0a
Rt86win7.sys 2/26/2009 5:04:22 AM 0x92a3f000 0x92a64000 0x00025000 0x49a65b16
netw5v32.sys 3/26/2009 12:10:37 PM netw5v32.sys+83101 0x9262c000 0x92a3f000 0x00413000 0x49cba8fd
How To Find Drivers:




Quote:
- search Google for the name of the driver
- compare the Google results with what's installed on you... Read more

Read other 6 answers
RELEVANCY SCORE 63.2

Please help me , many BSOD's every day ... 15 min ago reinstalled Windows 7 Ultimate x86 , and up now had 3 BSOD's ...

Hello this is .zip folder with BSOD info .

Attachment 261833

A:so many BSOD's on day , error 0x0000007f , and over kind ...

Please post back the following information:

Windows updates / activation

Cheers

Dave

Read other 5 answers
RELEVANCY SCORE 63.2

Hi,
 
Hope you're well.
 
I keep getting a BSOD in both windows 10 and windows 7. I have recently installed windows 7 and have received and error code:
0x0000007F (0x00000000000000010,0x0000000080050033,0x00000000000406F8,0xFFFFF80002cc9342) 
 
In event view viewer an error has occurred:
 
The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID 
{9BA05972-F6A8-11CF-A442-00A0C90A8F39}
 and APPID 
{9BA05972-F6A8-11CF-A442-00A0C90A8F39}
 to the user kevin-PC\kevin SID (S-1-5-21-79585836-2096477218-3416894218-1000) from address LocalHost (Using LRPC). This security permission can be modified using the Component Services administrative tool.
 
My Specs:
Tntel 2500k
Corsair 12gb ram 1600
Asus Extreme 4 gen3
gtx 970 
Corsair 650w psu
SSD Evo 850
 
Regards,
Kevin 

A:BSOD Error code 0x0000007F

Hi,
 
Hope you're well.
 
I keep getting a BSOD in both windows 10 and windows 7. I have recently installed windows 7 and have received and error code:
0x0000007F (0x00000000000000010,0x0000000080050033,0x00000000000406F8,0xFFFFF80002cc9342) 
 
In event view viewer an error has occurred:
 
The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID 
{9BA05972-F6A8-11CF-A442-00A0C90A8F39}
 and APPID 
{9BA05972-F6A8-11CF-A442-00A0C90A8F39}
 to the user kevin-PC\kevin SID (S-1-5-21-79585836-2096477218-3416894218-1000) from address LocalHost (Using LRPC). This security permission can be modified using the Component Services administrative tool.
 
My Specs:
Tntel 2500k
Corsair 12gb ram 1600
Asus Extreme 4 gen3
gtx 970 
Corsair 650w psu
SSD Evo 850
 
Regards,
Kevin 
Hi
I can't seems to find your dump files in your filecollector. Thus unable to analyze. 
Please re-upload again.
Thanks.

Read other 8 answers
RELEVANCY SCORE 63.2

This has been going on a while. My power supply and CMOS battery both went out recently and just got around to replacing them, although this issue has been going on way before that. After booting up today I got two separate BSODs. The most recent has the 0x7f stop code. After the first BSOD today I updated my BIOS to the latest version, hoping that might help, but soon after had the 0x7f error. If someone could take a look for me and tell me what I'm looking at and what needs to happen to fix this, that would be fantastic. Thank you!

Read other answers
RELEVANCY SCORE 63.2

Hi all,

I seem to be the only one in my office getting a BSOD (it happens at random intervals, few times in a month then maybe a few times a day for a few days in a row)
We all have the same PC's and I'm on my third one but still getting a BSOD so I'm convinced it must be something I'm installing that is causing the issue.

I've uploaded the dump files using the SF Diagnostic Tool so hoping I can get some help in figuring out what the problem is. It is so frustrating as I am losing work each time

Many thanks,
Declan

A:BSOD on my office PC, error 0x0000007f

Hello db001.

► It is McAfee that is blocking your network access and causing BSODs thereby.

Code:
fffff880`096e9858 fffff880`018168f3Unable to load image \SystemRoot\system32\drivers\mfewfpk.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for mfewfpk.sys
*** ERROR: Module load completed but symbols could not be loaded for mfewfpk.sys
mfewfpk+0x48f3
Uninstall McAfee Using McAfee Removal Tool.
Use Microsoft Security Essentials as your antivirus with windows inbuilt firewall, and free MBAM as the on demand scanner.

Download and install those, and then run full system scans with both of them, one by one.

► update the network driver.
First, download the network card driver from manufactuer's website, Realtek
Then reinstall the driver:
Click the Start Button, type "devmgmt.msc" (without quotation marks) in the Start Menu Search box and press Enter.
Double click to expand "Network adaptors".
Right click your network card and click Uninstall.
Check "Delete driver software for this device" check box, click OK.
Restart the computer
If windows does not auto configure the appropriate drivers at startup, install the downloaded one manually.
► Install Service pack 1 and all the other upates.

Code:
Windows 7 Kernel Version 7600 MP (8 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS
Built by: 7600.16617.amd64fre.win7_gdr.100618-1621
Learn how to install Windows 7 Service Pack 1 (SP1)
S... Read more

Read other 5 answers
RELEVANCY SCORE 63.2

Hello all, I just started getting BSOD the other day. I have tried reformatting a few times and even burned a new windows 7 disc and it is still happening. At first it seemed to happen when playing games such as Dark Souls 2, World of Tanks and World of Warcraft but it also just happened while browsing the web. I am suspecting there is a hardware issue somewhere but I am not sure how to isolate the problem and really dont want to have to build an entire new computer. If anyone has any suggests that could help please let me know!

Attached a picture and the BSOD.zip file. Please let me know if there is any additional information I should upload.

Thanks so much for any information or suggestions anyone is able to provide.

A:BSOD every few hours, error 0x0000007f

If you wish to determine whether it's hardware or not then run these tests.
Stress test your CPU with Prime95

I recommend running Prime95 for around 2 hours



   Warning

As with most stress tests your component's temperature will rapidly increase.
It is advised that you download a temperature monitoring program like HWmonitor
Keep an eye on your temperatures and stop the tests if it starts to overheat

Stress test your graphics card with Furmark

I recommend running it for around 30 minutes



   Warning

Furmark will increase the temperature of your GPU rapidly so keep and eye on your temperatures

Memtest86 will test your RAM



   Information

Run Memtest86 for at least 8 passes so we get enough information to confirm that your RAM isn't failing

Stress test your CPU with Prime95

I recommend running Prime95 for around 2 hours



   Warning

As with most stress tests your component's temperature will rapidly increase.
It is advised that you download a temperature monitoring program like HWmonitor
Keep an eye on your temperatures and stop the tests if it starts to overheat

Stress test your graphics card with Furmark

I recommend running it for around 30 minutes



   Warning

Furmark will increase the temperature of your GPU rapidly so keep and eye on your temperatures

Memtest86 will test your RAM



   Information

Run Memtest86 for at least 8 pas... Read more

Read other 9 answers
RELEVANCY SCORE 62.4

Hello, laptop specs - Acer Aspire One AOD270. I'd like to use sandboxie as i need to use java (oracle).

i recently tried loading sandboxie with firefox and got the BSOD. Bluescreenview showed that the following was the the cause;

''caused by driver'' igdkmd32.sys ''file description'' Intel (R) WDDM Kernel mode driver ''product name''Intel Graphics Accelerator Drivers forWindows 7(R)

igdkmd32.sysis is a file of the INTEL GRAPHICS MEDIA ACCELERATOR 3600 SERIES, 8.14.8.1064 , driver on my laptop.

On the Acer laptop driver support site there a two VGA updates available , 8.14.8.1065 and 8.14.8.1075.

I've never updated drivers before so hoping for some guidance as no forum has been able to help me as yet and seing as my warranty has expired Acer is not much help.

eg,which one should i choose, do i need to delete the old one before installing the new, and what is the procedure for updating ?

I've asked on other forums but as yet i've found no guidance, so any help much appreciated.

Thanks

A:Intel Graphics Accelerator Drivers

removing the old drivers prior to doing an update is of course the best way to go, though isn't required but problems could occur installing over the top of old drivers.

hope doing the update will resolve the issue.

Read other 2 answers
RELEVANCY SCORE 62.4

I've been trying several different versions of Intel graphics drivers (HD 4000) to fix the BSODs, but keep getting them. I got one during a heavy CPU load (x264 encoding) a couple days ago on the latest Windows 8.1 driver from Intel's site. After a while of looking up drivers I downgraded to a Windows 8 driver (3165), but then got one just now while trying to put my laptop to sleep. I could only upload the info for the most recent one, because before that I had my pagefile disabled.

Thanks

edit: Also, ever since the bsod related to video encoding, I monitor my CPU temps with RealTemp and keep my laptop propped up with a fan underneath.

A:BSODs from Intel graphics drivers

Most laptop video (currently) has dual video cards.
As such, it requires that the OEM carefully match and customize the drivers for each card and the drivers for making them work nicely together.

Using the stock Intel drivers may not be the best solution here. On my Samsung 780 series laptop I have graphics issues when using the Intel-provided graphics drivers and the AMD provided graphics drivers (and have seen the same on systems with nVidia graphics). Cleaning these drivers off and installing the Samsung provided drivers fixes these problems for me - I would suggest the same for you.

There is only 1 memory dump in the uploaded reports. If you're using a disk cleaning program, please stop while we're troubleshooting.

Only 51 Windows Updates installed. Most systems have 60 or more. Please visit Windows Update and get ALL available updates (it may take several trips to get them all).
Don't worry about the specific number, it's just important that you have checked and installed any updates that were available.

Please note the drivers below that date from before the release of Windows 8.1 (17 Oct 2013) - check to see that each and every one is compatible w/Windows 8.1 (at the manufacturer's website). If not, you must either remove the device and it's software - or locate a Windows 8.1 compatible update on the web. Removing some drivers may make the system unstable - so if you're unable to find updates, post back for info on the one's that can/cannot be safely removed... Read more

Read other 5 answers
RELEVANCY SCORE 62.4

Hello,

My laptop has Windows Vista Home Premium (64-bit) on a partition and I am having trouble finding drivers for my graphics card, which is an Intel HD Graphics 4000 model. I have tried my manufacturer's website, Intel's drivers, and all of them don't work. They end up with an error like 'This operating system is not supported.' Also, when I contact support, all they say is to upgrade to Windows 7. When I did get a driver to install, it messed up my screen, so I had to revert to the VGA Graphics Adapter again. If someone could help me find some drivers that were made for Vista or were for Windows 7 but were released quite a long time ago, that would be awesome.

Thanks,
Matthew

A:Intel HD Graphics 4000 Drivers

Who makes your laptop?

Read other 18 answers
RELEVANCY SCORE 62.4

I am trying to update the graphics drivers for my laptop using the intel driver update utility to fix a problem with a game that I am playing (Overwatch). However when I try to use the facility it says that I have to use drivers that are from HP. How do I obtain these HP drivers or how can I use the drivers directly from Intel?

Read other answers
RELEVANCY SCORE 62.4

I want updated graphics drivers for Intel 845GL motherboard for Windows 7.

A:Want graphics drivers if for Intel 845GL

google is a good place to start looking.

Read other 1 answers
RELEVANCY SCORE 62.4

Hello,
I have been BSOD free since March 2014. Now while I was in the skills menu of Skyrim and playing music on Zune's software, my computer crashed for no reason. I have replaced the motherboard on this system from the last diagnoses from this site. I am now at a loss of ideas what this could be since I have tested all other components to this system already and all of them passed their tests. Attached is the SF Diagnostic tool results.

A:BSOD playing Skyrim, error 0x0000007f

Code:
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************

UNEXPECTED_KERNEL_MODE_TRAP (7f)
This means a trap occurred in kernel mode, and it's a trap of a kind
that the kernel isn't allowed to have/catch (bound trap) or that
is always instant death (double fault). The first number in the
bugcheck params is the number of the trap (8 = double fault, etc)
Consult an Intel x86 family manual to learn more about what these
traps are. Here is a *portion* of those codes:
If kv shows a taskGate
use .tss on the part before the colon, then kv.
Else if kv shows a trapframe
use .trap on that value
Else
.trap on the appropriate frame will show where the trap was taken
(on x86, this will be the ebp that goes with the procedure KiTrap)
Okay so thats complicated let me break it down.






Quote:

This error message can occur if either of the following conditions exists:
Your computer has hardware or software problems (hardware failure is the most common cause).
You try to over clock the speed of your computer's processor (for example, you set a 150 MhZ processor to run at 1... Read more

Read other 9 answers
RELEVANCY SCORE 62.4

I tried to do a bit of research on my own and it appears to be a driver issue however I don't know which driver in particular.

Read other answers
RELEVANCY SCORE 62.4

Good day to you, gentlemen!

I've been having an agonizing problem for months now, and I just can't seem to find the source of the problem on my own, so I am asking for your help.

I've been getting randomly occurring BSODs for a while now(0x0000007F). I removed all the dust from my PC, checked cable connections, removed and reinserted RAM sticks, updated my VGA drivers and had my RAM checked by memtest, but it hasn't picked up any errors after 7+ passes.
If you need to know anything else, I'll gladly provide you with further information.
Thank you for taking the time to help, I'd be eternally grateful if somebody could figure it out for me.

A:Randomly occurring BSOD, error 0x0000007F

Please post the following here before we begin: Windows Genuine and Activation Issue Posting Instructions

Read other 8 answers