Over 1 million tech questions and answers.

Help dual booting Windows 8

Q: Help dual booting Windows 8

I've been following this guide:
Dual Boot Installation - Windows 8 and Windows 7 or Vista

The problem is that when I go to install Windows 8 it doesn't recognize the partition I made. This is the partition I made.

This is what it looks like when I go to install Windows 8 on that partition.

Neither of the 2 partitions I made appear on that list. I don't know what I'm doing wrong. Any help would be appreciated. I would really like to try this out before I decide that I want to purchase it.

RELEVANCY SCORE 200
Preferred Solution: Help dual booting Windows 8

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: Help dual booting Windows 8

Hello ScoobyDoo, and welcome to Eight Forums.

The 39.06 GB unallocated space on Disk 0 doesn't show up since you already have the max of 4 primary partition on the disk. You could use METHOD TWO in the tutorial below to create a logical partition with the unallocated space instead that should show up afterwards.
Partition / Extended : Logical Drives - Windows 7 Forums

I'm not sure what the unallocated space on Disk 1 is not showing up though. Creating a new simple volume with the unallocated space to format it should have it show up afterwards.

Partition or Volume - Create New - Windows 7 Forums

Hope this helps,
Shawn

Read other 14 answers
RELEVANCY SCORE 57.6

Recently I purchased a laptop with windows 8 64 bit pre-installed in it. For my job purpose, I needed windows 7 32 bit. After searching the web and also using the information I got from this site, I disabled secure boot, deleted the recovery partition and converted GPT partitions to MBR. Then I shrink the Big partition in which windows 8 was installed to make room for the windows 7 partition. Then I created a new partition and installed windows 7 on it. After this whenever I switch on the computer, a message come up, saying that a required device cannot be found and windows is to be repaired. The only way in which I can start windows is to go to bios, select the boot options and then select boot from notebook hard drive.

Can anybody please tell me how this problem can be solved

A:Booting problem with dual booting with windows 8 and 7

when you created the new partition did you make itin front or behind the existing partition?

If your boot manager is looking to boot Win 8 on Disk 0 Part 1, and you created the new partition in front of Win 8, your Win 7 will now be located on Disk 0 Part 1 which is where the boot manager is expecting Win 8

can you send us a screen cap of your disk management?

Read other 7 answers
RELEVANCY SCORE 52.8

Hi all - so very sorry for the lengthy post but I feel giving necessary information ahead of time can help a lot...........I spent the better part of yesterday running around the Net and even here for instructions on how to set up a dual boot setup. While what I found was great the instructions weren't very helpful to my specific situation. I've never set up a dual boot system so every part of this is new to me and while I'm not a novice with computers when it gets into "installers" and the inner workings of Windows I get lost.I have a 7-1/2 year old super Gateway desktop that came with XP Pro, changed it to XP Pro Retail, but only have gone as far as SP2 because SP3 always gave me problems. The system has royally passed the Windows 7 Advisor test except for a couple of printers I have connected to it but the hardware is just fine. At the time of purchase in July 2002 the system cost me $6,000 - half of that was for the 22" LCD digital/analog display alone. I've gutted it out as much as I could over the years and while I'd love to upgrade the board, processor and memory, it being a Gateway is pretty much impossible given the proprietary way they make their systems. The system is a 700XL desktop, was considered their top-shelf machine at purchase, and now has 2 Gigs of Rambus memory (came with one gig), I swiped out the OEM video card for an nVidia GeForce 6800, 128 Meg AGP 8x/4x, changed the OEM sound to the Creatives Live Drive Bl... Read more

A:Dual Booting XP with Windows 7

Hello LadyKeys,

I'm by no means the authority on this subject, but I have been success in completing this very task of dual booting XP & 7. I currently dual boot Win. XP 32bit & Win 7 64bit.

Solution: The trick, as with all basic Windows dual boot setups (without using special boot manager software), is that the older OS must be installed first, in this case Windows XP. Also, I believe Windows XP must be installed on the primary drive (I have all SATA drives and I did not get the dual boot menu when XP was installed on the drive assigned to port 1 vs port 0. I had to specify in the BIOS which drive to boot from in order to get to the specific OS). After you have Windows XP installed then install Windows 7 on the secondary/slave drive and that should be it. At boot up you should get a boot menu with an option to boot to an "Earlier Version of Windows" or Windows 7.

Note: Both drives should be connected when you install Windows 7 so that Windows 7 will detect the Windows XP partition and setup the boot manager accordingly. Finally, take care not to install Windows 7 on the same drive/partition as Windows XP during the Windows 7 installation.

Good luck,
Technine22

Read other 14 answers
RELEVANCY SCORE 52.8

Hi everyone. I was hoping someone could walk me through the process of getting my computer to dual boot XP and Windows 95. See, I had this old Packard Bell Legend 220CD (A 450 model) from back in 93 that was sitting around for years. A few days ago I got curious about what was still on it and tried to boot it up. Battery was dead. Oh well. So I pull out the hard drive and put it in y newer computer and it's still fine. It does have an install of windows 95 already on it and what I want to do is tell my computer to boot only that drive and run the windows 95 instead of the XP already on my current hard drive. I don't know if this is possible but I'll list some information about my current computer to help0 anyone along who may be interested in helping me with this.
Current Computer: Compaq Pressario S6000V
1.24 GB RAM
2.5 GHz Pentium 4
Windows XP Home Edition SP 2
drives are listed as basic and my new hard drive has 147GB's to spare, with one partition.
THe new drive: FAT 32
The Old drive FAT (also it's 850 mb....lol)
I currently have my older drive set to boot first.
Chip Set: 845G
Chipset COmponents-
memory controller: 82845G/GE/GL/GV
I/O Controller: 82801DB (ICH4)

The Drive with Windows 95 was pulled from a box with FOD: 4504x4
I also have access to a variety of DOS bootdisks. I was pretty young when DOS was the way of the world so I never really learned much about, but if they can help, they're at our disposal.
If there's any other inform... Read more

A:Dual Booting With Windows Xp

I think it will be easier to replace the battery in the old computer than it would be to get the old hard drive to boot on the new computer.

Normally for dual booting xp the older OS needs to be installed first, then an XP install will detect the existing installation and let you set up dual booting.

IMHO Win 95 was a horribly buggy OS and deserved to die well before it was replaced by the bug-ridden Win 98.

Read other 2 answers
RELEVANCY SCORE 52.8

Quick note: All drives I mention in the post ARE partitions. D and E drive are partitions and I only have one HDD.

Hey guys, I'm just wondering about something recently regarding drive letters with dual boots. Lately I installed Windows 7 in dual boot with XP (XP was the OS that was installed first). When I booted to Windows 7, it started off as C drive, and when I booted back to XP, XP was C drive. Okay, that's sweet, I understand that the OS I'm booting to will be the C drive, right?

Now that's really not much of a problem, but I also read on Google that you'd also be able to install XP on a "fixed drive letter" - sorry if that's by any chance confusing, but what I mean is, being able to install XP on E drive, and when you boot to XP, it'll stay as "E " and NOT make itself "C".

Does this particular tutorial achieve that?

http://www.howtogeek.com/howto/8790/...puter-with-xp/

I'm curious since this Vista tutorial seems to mention XP being on a fixed drive letter:

http://www.howtogeek.com/howto/windo...ista-computer/

(Scroll down on that link and it says "This is a critical piece of information: Windows XP will be installed on the D: drive, even in Windows XP? so you?ll need to keep that in mind when tweaking your system." I'm just wondering if this is the case for the Windows 7 tut as well.)

This is probably the most important thing I want to know though - if I do want to have XP on a "fixed drive letter&quo... Read more

A:Dual booting Windows 7 with XP (XP second)

*Bump*

Read other 1 answers
RELEVANCY SCORE 52.8

Hello, I'm new to the forum and blah blah blah who cares. I'm not a computer expert here, so I thought about coming here seeking for help. Anyways, into the topic, I wanted to ask a couple of things about installing Windows XP Home SP2 Upgrade (not full) on a partition (I'll get a cheap old Windows copy for the upgrade to work), with a pre-installed Windows 8 in the other partition.

1) Has anybody tried it? Does it work well? So far I have found no guides on how to do it, but many on how to install XP on Windows 7. Is it the same procedure?

2) I have heard that installing an XP Upgrade will wipe/reformat an entire HD, both partitions as if they were not partitioned/united. Is that true?

A:Dual-booting Windows 8 and XP

No that's not true Windows XP will not wipe both partitions. But you will not have the dualboot option. This tutorial can help I know it is for windows 7 but it will apply to 8 as well Dual Boot Installation with Windows 7 and XP - Windows 7 Forums

Read other 24 answers
RELEVANCY SCORE 52.8

Hi guys,

I am currently using Windows 7 but have had to install Windows XP due to some programs not working with Windows 7. I have fully installed Windows XP but at start up it does not give me an option to choose between the two and automatically loads up XP. Is there anyway i can sort this out.

Thanks for your help in advance.

A:Dual Booting Windows 7 & XP

Welcome!

See this tutorial: Dual Boot Installation with Windows 7 and XP

You can also try running a Startup Repair on Windows 7. If the repair doesn't work, try setting the 7 partition as active: http://www.sevenforums.com/installat...-problems.html

Hope this helps,
~JK

Read other 3 answers
RELEVANCY SCORE 52.8

hey guys, Im upgrading a computer, went to 1gig proc, new motherboard, ram, etc.. I put in a 60 gig HD and have a 8gig also. the 60 will have win2000 installed on it, the 8 has 2000 already installed, do I have to redo the 8 gig as win 95 or 98 in order to set it up as dual boot? and how do I set it up for dual boot, I cant remember .... please help!!!!
 

A:windows dual booting

Read other 6 answers
RELEVANCY SCORE 52.8

I currently have Windows 7 Ultimate 64bit installed on my computer on a SSD drive, and I'm trying to install Windows Server 2003 on a second hard drive (regular SATA II HDD).

When I boot with the Windows Server 2003 CD, everything seems to be fine... it pops-up the usual blue screen and the drivers are loading, but once the drivers are done loading, I get this error message:

"A problem has been detected and windows has been shut down to prevent
damage to your computer.

If this is the first time you've seen this stop error screen, restart your
computer. If this screen appears again follow these steps:

Check for viruses on your computer. Remove any newly installed hard drives
or hard drive controllers. Check your hard drive to make sure it is properly
configured and terminated. Run CHKDSK /F to check for hard drive corruption,
and then restart your computer.

Technical informaiton:

*** STOP: 0X0000007B (0XF789EA24, 0XC0000034, 0X00000000, 0X00000000)"

Any idea why this message pops-up and prevents me from installing Windows server 2003? Is it possible to have a dual boot with Windows 7 and Windows Server 2003?

Any help would be much appreciated. If more info is needed, let me know.

A:Dual booting with Windows 7?

The generally accepted method, or at least the one I personally use, is to always install the older OS first, then install 7 afterwards.
The win 7 bootmgr won't have issues allowing the older OS to boot. However, the older OS is very likely to cause problems for windows 7 if attempting to write to boot sectors over it.

Read other 4 answers
RELEVANCY SCORE 52.8

Hello;
I'm building a Dual boot machine with windows 7 Pro. and 10 Pro.  i dived a 1TB drive, installing windows 7 Pro goes great,7 up and running..... after loading windows 10 Pro on the second Partition..( 10 runs grate) But now  I can not restart windows
7 from the boot menu, The system gives me a "system and or drivers can not be verified"  using F8 to try to Disable vitrification just takes me in a loop to the advanced boot menu..   How can i get past this????......

Read other answers
RELEVANCY SCORE 52.8

Hi, I am currently using a lenovo G570 running windows 7 and it comes with all partitions fuul so i can not create a new one. from what i know i need to install windows 8 in another disk partition but i cant create one... how can i do the dual boot or modify the existing partitions?

A:dual booting windows 7 & 8

If your harddisk is full, you cannot create another partition. You need to format the old one and install it in newly formatted partition. (warning! All data on the formatted partition will lost!) But move out all important data before doing so.
 
Thank you.

Read other 7 answers
RELEVANCY SCORE 52.8

I currently have XP, considering upgrading to 7 (64bit)

I'm a little scared i'm not going to like 7 so want to hang on to XP as a back-up.

What I want to know is, using cloning software (I think i'll either use the seagate software as I have a hardrive or two of theirs (Acronis) or XXClone) can I clone my XP system on to a separate hardrive, upgrade to 7 from there and boot from the separate HDD's while I decide?

Will the licences get grumpy cos i'm running from the same copy of XP?

I've never actually tried cloning before so i'm also a little worried that the XP clone wont work to start with (after forking out for a new HDD to clone to)

Thanks in advance

A:Dual Booting XP Windows 7

The best way would be to make another partition for Windows 7 then do a clean install of Windows 7. But make sure your system will handle and is compatible with Windows 7 before installing using Windows 7 Advisor.

How to setup dual boot for Windows XP and Windows 7.

Note in the illustration it shows to use Windows 7 DVD. I recommend using Windows XP to shrink the volume (Partition) Partition Wizard Home Edition to resize (Shrink) the volume to make a suitable partition for Windows 7 I recommend at least 60GB for Windows 7. Make sure your Hard drives or the partition which XP is on is big enough and has enough room to make a partition for Windows 7.

Read other 2 answers
RELEVANCY SCORE 52.8

Hello,

Apologies if this is in the wrong area, I don't post here that often so please move this if appropriate.

I have recently just upgraded to a new laptop, due to my old laptop (4 years old, running windows 7) has been giving me overheating issues for what seems like an eternity. This new laptop, a HP with intel i7, has Windows 10.

The laptop runs a lot cooler than my old Windows 7 laptop however some of the older games that I have, which work fine on windows 7, do not on windows 10.

Since my laptop has a 2TB hard drive, I am thinking about dual booting Windows 10 and 7 on the same laptop. I know this is possible, but I have never performed a dual boot setup on a laptop before and am worried I might mess things up.

Can someone on here please give me some detailed help on performing a dual boot? This would assume partitioning the hard drive into (C) Windows 10 (approx. 1TB), (D) Recovery partition for 10 (already installed) and (F) 1TB for Windows 7. (The E drive is my DVD writer.)

Thanks in advance for your help!

Read other answers
RELEVANCY SCORE 52.8

ok guys and gals im new here so go easy on me. i have managed to set up a windows 7 on a dual boot with vista. everything is working properly, but all my drive letters are different. i installed an extra hard drive to store media on. i want that hard drive to be same letter in windows 7 as it is in vista, so i can get my itunes library to work. when i go to disk management the drive letter i want to switch it to is unavailable. any advice would be nice. Thanks in advance

A:Windows 7 and Dual Booting

Here's a link to a help item for changing the drive letters in Vista: http://windowshelp.microsoft.com/Windows/e...f110521033.mspxAs I understand it, the process is just about the same for Windows 7.Hope this helps.Cheers,RonWindows Outreach Team

Read other 1 answers
RELEVANCY SCORE 52.8

Hi

I know there is a thread on this related to a very good tutorial which I used to set up my dual boot with DualBoot Pro in the first place. Unfortunately the thread is so long that it gets to the point of not being very helpful so I thought it best to create a new topic.

I tried to use my xp system for the first time the other evening and it wouldn't boot. Just kept booting into Win7 (main system). I got into a bit of a pickle using dualboot pro to try to change the drive for the xp system and I also tried creating a Windows Legacy boot loader on the partition on whcih XP resides. All I succeeded in doing was stopping Win7 from booting as ntdlr could not be found. I fixed this by restoring the win7 mbr from command prompt but now, I need to work out what's wrong.
DUALBOOTPRO boot info - does this indicate what is wrong? Why can I not boot into the XP system when I select it on the start up dos screen?

Windows Boot Manager
--------------------
identifier {bootmgr}
device partition=C:
description Windows Boot Manager
locale en-US
inherit {globalsettings}
default {current}
resumeobject {53560040-0fd5-11df-8d26-a656ea69480c}
displayorder {current}
{ntldr}
toolsdisplayorder {memdiag}
timeout 30

Windows Boot Loader
-------------------
identifier {current}
device partition=C:
path ... Read more

A:Dual Booting WIndows 7 and XP

Hve you tried Easy bcd??

Read other 4 answers
RELEVANCY SCORE 52.8

Okay Guys, I Was Trying To Dual Booting My Computer...
Originally It Was Windows 7..
And I Wanted To Add The Mac On It..
I Used A Program Called: "iATKOS v7" Or Something Like That..
Everything Worked Just Fine (After I Try It Around 3 Times...)
I Restarted Finally My Computer, Found 2 Lines:
1- Windows 7 Ultimate
2- NTS Mac OS

I Was So Happy That FINALLY The Dual Boot Worked!!

When I Pressed It... One New Problem Put An End To My Happiness...
On The Screen We Can See That:

"Before You Begin...
Press the key immediately to the right of the Shift key on the left side of the keyboard that can't be identified.

Press the key only once and do not hold down the key for a long time.
When the key is recognized, the next panel will appear."

And A Picture Of Shift And A Button On The Right Of The Shift Key Is Marked Like They Say To Me To Press It..

And In The Bottom Of The Page, They Say: Identifying your keyboard...

It Had Been Around 2 Hours.. And Nothing Appeared..
I Tried All Keys In The Keyboard, And Nothing Shows Up!!!

Any Help Please!!
I Will Really Really Really Appreciate It!!


And, By The Way, The Key On The Right Of The Left Shift Is Not The "Z" Key??

A:Please HELP!! I Need A Help In Dual Booting: Windows 7 + Mac OS X

Why not use bootcamp?
Apple - Support - Boot Camp

Read other 1 answers
RELEVANCY SCORE 52.8

Hi there,

I recently bought a Macbook Pro and have installed a version of Windows 7 which I purchased to put on my old Vaio laptop.
The installation had no troubles and my product key worked. However, it is now telling me that it is unable to activate windows because the product key is not valid with this version of Win7 (or words to that affect).
IS there a way around this at all? It is clearly a 100% genuine version of Win 7 Professional I bought and downloaded from Microsoft.
Someone has suggested that I uninstall it from my old laptop and try again but i cannot because I am selling my old laptop to my parents.
I hope someone can help
Thanks,

Ben

A:Dual booting Windows 7 on Mac

You can't use the same key on two different computers.

Read other 1 answers
RELEVANCY SCORE 52.8

Hi and thanks for reading and helping.

I created a new 300gb partition on my 1tb hdd currently running windows 7 and installed XP Pro onto the new partition using the standard methods.

After the XP install everything booting into XP and has been working fine, all drivers are installed and 2 hours later everything in smooth as butter...

Except I can't figure out for the life of me (after 10+ google searches) figure out how to get back into my original windows 7 install. I can't seem to get windows boot manager to come up when I boot.

Suggestions?? ^_^

A:windows 7 dual booting help.

Run the Windows 7 Startup Repair.
Startup Repair

Once you're running Windows 7
Add XP with EasyBCD
EasyBCD - Take control of your boot loader | NeoSmart Technologies
No need to register, just select "Download"

Read other 4 answers
RELEVANCY SCORE 52.8

Is it possible to dual boot Windows 7 Pro, one partition being a 32 bit system, and one being a 64 bit?
I have a program that just won't run on 64 bit, and my processor doesn't allow for Virtual PC, so can I have a separate partition with 32 bit Windows 7 Pro running?

A:Dual Booting Windows 7 (32 & 64 bit)

Yes its possible to dual boot Windows 7 32bit and 64 bit. Install Windows 7 64bit on one partition. Then shrink that partition and install Windows 7 32bit to the new (shrinked) partition. Also, use VMWare player or Sun Virtualbox to run Virtual OS. No need of any Virtualization support CPU.

Read other 9 answers
RELEVANCY SCORE 52.8

Hello,

Apologies if this is in the wrong area, I am new to this site so please move this if appropriate.

I have recently just upgraded to a new laptop, due to my old laptop (4 years old, running windows 7) has been giving me overheating issues for what seems like an eternity. This new laptop, a HP with intel i7, has Windows 10.

The laptop runs a lot cooler than my old Windows 7 laptop however some of the older games that I have, which work fine on windows 7, do not on windows 10.

Since my laptop has a 2TB hard drive, I am thinking about dual booting Windows 10 and 7 on the same laptop. I know this is possible, but I have never performed a dual boot setup on a laptop before and am worried I might mess things up.

Can someone on here please give me some detailed help on performing a dual boot? This would assume partitioning the hard drive into (C) Windows 10 (approx. 1TB), (D) Recovery partition for 10 (already installed) and (F) 1TB for Windows 7. (The E drive is my DVD writer.)

Thanks in advance for your help!

A:dual booting windows 7 and 10

Hi spotify95, welcome to Ten Forums. These are from the tutorial forums. The first to add a partition. Partition or Volume - Create New - Windows 7 Help Forums . The second to dual boot. Just substitute win 7 for win 10 where it appears since the tutorial is for adding a win 10 to an existing win 7 system. Windows 10 - Dual Boot with Windows 7 or Windows 8 - Windows 10 Forums .

Read other answers
RELEVANCY SCORE 52.8

Hi, I am considering dual booting windows 32 bit and 64 bit, each on a separate drive. How do I go about this? can I simply pop in the dvd and choose a drive, and it knows to bring up a dual boot menu? Are there any considerations?
Also, I would like to move my games, is this possible? Do i have to install again, and for steam games download them again?
Also, are SSD drives worth it? Thanks and sorry for noob questions.

A:Dual booting 32 bit and 64 bit Windows 7

Hi,

Yeah you can install two separate OS's on separate drives but why do you want a 64bit and 32bit OS of Win7? Win7 64bit allows you to use 32bit options for installing games etc. anyway so essentially it already does both 32bit and 64bit in the one OS. But if you want to continue then read this post Dual Boot Windows 7 & XP on Different Drives?

This I found out for someone just yesterday but they were installing 7 and XP on separate HDD's but i'm sure the principles are exactly the same. As for moving games you would have to re-install the games on the other HDD but you can take the save files from the games folder in C: /Programs/whatever game it is, put them on a flash drive or dvd then copy them across to the exact same folder on the other HDD.

Hope this Helps

Steve

Read other 3 answers
RELEVANCY SCORE 52.8

Hello. I have looked through the forums, but have not seen this exact problem listed. I hope someone can help me.

I bought a new computer kit last month, and after I got it all together, I installed Windows 7 Pro 64. It has the AMD A8-3850 Quad core CPU, 8gb of RAM, on an MSI A75MA-G55 motherboard, and a 1tb SATA HDD. One of the first things I had to do after installing the OS was to flash the BIOS on the MB. I have everything the way I want it on the computer now, and made a backup image of the C drive.

For the most part, everything is good with Win7. The only thing I don't like is with the sound card. I like to sing Karaoke on a website, but I couldn't get the "What you hear" function on the onboard sound card. So I bought a SB X-Fi XtremeGamer. I have the WYH function now, but my voice coming through the headphones has a lag that throws me off. So I have decided that I want to do a dual boot with Windows XP.

I have read many tutorials that tell how to do a dual boot setup, so I set out to do that. When going into the WinXP setup, I was having a problem with the hard drive. So I decided to reformat the hard drive and install the winXP first, then just install the Win7 backup afterwards.

WinXP saw the hard drive and had me do the partition and format then winxp installed fine, no problems. Ok, one problem. It installed on the C: drive. It didn't give me another option. And I know when I go to put the backup of WIN7 back on, it will want to be on the C: drive a... Read more

A:Dual booting Windows 7 and XP

Hello ShdwKnght, welcome to Seven Forums!


You really screwed yourself by forcing a 5th partition and accepting a Dynamic disk; XP will probably stop booting before long and I doubt you'll be able to get Windows 7 installed at all as-is; do you have good back-ups of everything on the entire HDD?

Read other 9 answers
RELEVANCY SCORE 52.8

just wondering about the dual booting. ive currently got windows xp installed and im wanting to do a dual boot with windows 98. if it can be done. i have a 80 gig hard drive and its partitioned into 3 sections. am i able to use my one (partitioned) hard drive to do the dual boot. if so how do i do the dual boot???

 

A:dual booting Xp with windows 98

Read other 16 answers
RELEVANCY SCORE 52.8

My PC is installed with Windows 7 at Drive - C. Today due to necessity I installed XP in Drive - D. After successful installation, I went for restart the system. But after booting, at the firsthand XP is opening. Now there is no scope for me to choose between Windows 7 & XP. How to overcome this ?

A:Dual booting with windows 7 & xp

Is this dual boot setup on one single drive or on two different hard drives? Is the XP install activated as the primary drive? Can you post a screen shot of your disk management window?

Read other 9 answers
RELEVANCY SCORE 52.8

Right now as it is, my C drive is divided into C and D. On the C is my Windows ME, under properties tab it says Local disk, FAT32 Used 1.89 GB free space 13.66GB. Under D properties tab it says, Local, RAW Used 48.0 KB, free space 21.66GB. I want to dual boot Me with NT. I put my 3 floppy disks in, everything goes all right, except for a 1024 cyclinders? It says it is not an error but could cause it not to work right, but go ahead and push enter. The other problem that I am having is when it comes to the Partitioning stuff. What kind of information would you need to help me partition this hard drive so it will work. I have tried doing it the way I think, but then it finds and error and tells you to exit out. I'm new at this, but really need to get it to work. Thanks.
 

A:Dual booting with Windows ME

The easy way would be to use a program like partition magic. It will allow you to move and add partitions without losing anything you already have on the harddrive. After you create any extra partitions you want, start me and then run the xp setup, select advanced so you can pick that you want to select the drive where you want to install it. You can put it on the D driver and use anyother partitions you created for storage.
 

Read other 2 answers
RELEVANCY SCORE 52.4

Hi

I have been dual booting XP Pro 32-bit and Vista Ultimate 64-bit for some time now but haven't really found a good way to delete XP Pro (my first installed os) leaving my Vista os able to boot up normally. I have scoured the forums and was about to delete a lot of files from the XP partition but leaving the loader files and root files alone. This would enable me to free up a lot of drive space. Currently the 2 os's reside on a RAID setup one partition for XP and another for Vista.

OK so I have found the Windows 7 forums and thinks that it would be good idea to replace XP with Windows 7 but the upgrade options for the Beta do not allow upgrade to Windows 7 from XP.

If I upgraded XP to Vista 32-bit what would happen to my boot files etc etc and could I then further upgrade to Windows 7 leaving that and Vista 64-bit dual booting together?

Or is this a complicated way to do things?

What I really want to do is delete XP Pro - I am rather fond of Vista now and seems very stable. But I do not want to be faced with boot problems after deleting.

I currently have installed on both os's, Acronis's OS Selector and BCD Edit.

I really need a very accurate method rather than a theoretical answer - someone who has done this successfully please. I have spent too long wading through forums looking for a way of successfully deleting XP and receiving maybe this will work or maybe that type of answers.

Cheers

roz

A:Dual Booting but Want to Replace XP with Windows 7

Hello Rozel and welcome to the Sevenforums.

Deleting an XP installation while already having a vista one, is very simple.

You probably are already using Vista's BCD boot loader to boot your PC with the 2 OSes.

So, you should be able to simple delete the XP folders on the XP partition and you're done.

You won't have any problems with Vista booting, and even if you do, the "startup repair" option does the trick from the Vista's Boot DVD.

If you fullfil the following criteria:

a) 2 partitions, one having XP , one having Vista
b) Booting with Vista's Boot Loader (BCD)

then you just delete the XP partition or folders completely, and you're done.

After doing so, you might want to delete the boot entry also, so you don't see a non-existing OS selection at startup. To do so, log on to Vista and open Command Prompt with administrative rights and type:

bcdedit /delete {ntldr} /f

Done.

Read other 9 answers
RELEVANCY SCORE 52.4

Hey,

I'm trying to dual boot Windows XP Pro 32-bit and Windows 7 with Windows 7 installed first; but this isn't the problem.

The problem is trying to boot Windows XP so it can install. I booted XP from an installation CD, then a blue setup screen appears, with some files apparently being loaded at the bottom of the screen (this is around the time pressing F6 to load drivers comes up). Then boom, I get blue screened with this error and cannot proceed:

A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

Check to be sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try chaging video adapters.

Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.

Technical Information:

*** STOP: 0x0000007E

I've been driving myself crazy trying to come up with a solution. My theory so far is that my SATA HDD can't be recognized by the Windows XP installation CD, therefore I need to add driver files to the CD (somehow?) so that they're compatible.

I have a:
Intel(R) PCHM SATA AHCI C... Read more

A:Dual booting, Windows XP and SATA

Hello, welcome to TSF !

Enter the BIOS at startup and set the drive controller mode to IDE (or ATA or PATA) instead of SATA. Disable native command queuing (ncq) and AHCI if you see those settings. Then retry with the XP CD.

If this doesn't help (or if the settings aren't there) you'll need to slipstream the SATA drivers onto your XP CD :
http://www.howtogeek.com/howto/windo...-installation/

you'll need the sata drivers but I couldn't find your motherboard here :
http://support.alienware.com/Support...downloads.aspx
What chipset does it use ? If you can find the drivers use the one called SATA/RAID or 32bit configuration floppy, if it's an executable file you'll need to find a way to extract the .inf, .cat and .sys files. See if your chipset is listed on this link, if so these are the drivers you need : http://downloadcenter.intel.com/Deta...=2101&lang=eng

Read other 4 answers
RELEVANCY SCORE 52.4

Hello everryone!
I am running Windows XP and would really like to share the hard drive with another OS "Linux" and dual boot. Trouble is i don't have a clue so would appreciate any help or even a tutorial that this old git can follow. Thanks folks
 

A:Dual booting Windows XP and Ubuntu

xlanou said:


Hello everryone!
I am running Windows XP and would really like to share the hard drive with another OS "Linux" and dual boot. Trouble is i don't have a clue so would appreciate any help or even a tutorial that this old git can follow. Thanks folksClick to expand...

Hello there i see you would like to dual boot with another operating system, this is a rather simple process.
Choose which operating system you would like to dual boot with windows (in your case this is Ubuntu)

Next boot off the Ubuntu live cd and wait till it enters the main desktop where it gives you the option to install it.

Then just follow the instructions, thats all I did and it worked fine.

When you come to the bit where you need to partition let Ubuntu do it automatically as i think that it does have that feature.

When you have installed it and rebooted you will get a grub loading message then you will get the chance to boot windows xp or Ubuntu and away you go.

Let us know how far you get and we will try and help
 

Read other 1 answers
RELEVANCY SCORE 52.4

Well nobody in the Ubuntu forums could help me so I thought maybe you fine folks here could. I have a 120 g ssd that I have tried several times to install Ubuntu on and cannot do it, no way , any way, whatsoever! I know the disks I have burned are good. I have a GA-Z68MA-D2H-B3 Gigabyte motherboard. I have changed settings in the BIOS and any thing I could think of to no avail. I have dual booted Ubuntu on every computer I have ever built but not this one! Huh uh! Anyone have thoughts on this? It's totally unnecessary, I just like to play around with Ubuntu. Any thoughts appreciated. Thanks

A:Dual booting Windows 7 and Ubuntu 12.04.2

Try this - just substitute LinuxMint for Ubuntu:

Dual Boot - Windows 7 and Linux

Read other 9 answers
RELEVANCY SCORE 52.4

Hello Can anyone help

How can i setup dual boot windows xp and windows NT
(current) (2nd OS)
Except with the 2nd OS completely hidden from the first OS, So no such files can be accessed from the firsy OS???

because last time i tried this dual boot, I could access all folders on NT while actively using XP

A:Dual Booting Windows XP, with 2nd OS hidden

Hi....

You can use a program called Acronis Disk Director to hide partitions until you want to unhide them.

hope that helps :)

Read other 7 answers
RELEVANCY SCORE 52.4

Hi, I think I made a grievous error last night. I was installing Windows 7 Pro (x64) onto my computer. The installation went well, but when I got into the OS itself, I noticed it wasn't installing anything onto the Win7 Partition. Instead it was installing programs into the WinXP partition. I initially thought it was because I didn't set the Win7 partition as the active partition, so I went into Disk Management and made it the Active Partition. BIG mistake because that erased the dual boot function. I received the BOOTMGR is MISSING msg and I had to repair via my Win7 Dvd.. Problem is my Win 7 repair just recovered the Win7 OS - and now I can't dual boot into XP. Is there a way to restore the dual boot functionality?
 

A:Problems w/ Windows 7 Dual Booting with XP

Read other 7 answers
RELEVANCY SCORE 52.4

I currently have windows 2k installed on my computer. I have two hard drives. The bigger one (6 gb) is formatted in NTFS, and the smaller one (1.5 gb) is formatted in FAT32. Windows 2k is installed on the NTFS drive, and I just want to install windows 95 on the other drive (to make playing my old DOS games much easier). I've checked other places on the web, and I am under the impression that (in order to do this kind of dual boot) I have to install Windows 95 on the correct partition (in this case my smaller hard drive) first, and then I have to REINSTALL windows 2k.

I would think that it would be much easier than that. But can someone give me some details into what I have to do? I don't mind reinstalling windows 2k (if that's what I have to do), but I just want to know if I really have to. And when I reinstall windows 2k, would it just overwrite the old win 2k files?

It would be great if someone could give me some detailed instructions as to how to go about this operation, but if not, that's ok, because I'm sure I can figure it out. But I would like to know about my main question. Thank you for your time.
 

A:Dual-booting Windows 2000 + 95

Read other 16 answers
RELEVANCY SCORE 52.4

~Background~

There were some power failures last week which caused some errors on my hdd and I spent 3 days reading this forum, trying to fix my windows 7 boot.

I finally fixed it after running chkdisk through a Windows repair disk after trying various other solutions to no avail. Thankfully, no files were lost (Besides the most important stuff was backed up)

I have an anxiety disorder and I work solely on the PC.
This incident was very hard on my health so I want to make sure that whatever happens I can get to work.

So I had an idea.

~Idea~

A while back I was reading about dual booting and it seemed quite interesting.
So, I've had this idea.

I have a 1 TB HDD.

It has two partitions, "System Reserved" and "C".

I create a new partition called G of let's say 100GB.

I then transfer my music, videos, photos to an external drive.

I uninstall all unnecessary programms/games from C.

I make sure C has about 50-60 GB of used space.

Afterwards, I make a system image using either the Windows 7 built-in tool
or Macrium Reflect/Acronis and transfer all my media back to C.

Could I then restore that system image on the new partition?

The end result I want to achieve is to have a "backup windows 7 installation"
If something happens to my Main installation, I can get to work on the second one.
Of course I backup my work to an external drive everyday.
I don't want to lose any more working days...

A friend of mi... Read more

Read other answers
RELEVANCY SCORE 52.4

In the firm i work in.I was asked to install Windows XP and win 2000 pro on a Pentium IV machine
with 80 GB hdd.I was also instructed to load XP as primary partition(as C and then win 2000.
After installing windows Xp and then installing win 2000,i find that i am not able to boot into Windows XP(although the dual boot screen appears)
this is the message i am getting
"Windows could not start because the following file is missing or corrupt
\windows\system32\config\systemd start up options for windows"
Why is this? I was told that windows 2000 has to be loaded before Win XP but the project requirement dictates that Win XP has to be installed on C: .
please do suggest how i can accomplish this.
 

A:dual booting windows XP and win 2k prof

Partition the drive, install W2K on D: first, then install WXP on C:, problem solved.
 

Read other 2 answers
RELEVANCY SCORE 52.4

Hi everyone. I have Windows 7 64-bit and I want to install Windows XP 32-bit for extra cross-compatibility. I know 32 bit apps can work in 64 bit but I also need my printers and other devices working.

I need help with a guide to dual-boot operating systems but I can't find a guide that includes Windows 7 as the first operating system. Could anybody help me by pointing me in the right direction?

Thanks,

-DarkPacMan77-

A:Dual Booting with Windows 7 Installed First?

Here is tutorial:Dual Boot Installation with Windows 7 and XP
See option two

Edit: Method two...

Read other 9 answers
RELEVANCY SCORE 52.4

It seems impossible to configure a dual boot on this machine, even when disabling EUFI and Secure Boot.  Has anyone had any success creating a dual boot with these OS's?  I have a new Win 7 DVD and a 500 GB Primary partition all set to go and installation hangs every time on the first reboot.
Seems to be failing because the bootloader fails.

Read other answers
RELEVANCY SCORE 52.4

Hi there,
I had windows 7 installed on a new partition on my pc which had XP Pro on the C drive. After removing windows 7 home premium and deleting the partition, I still get a choice at bootup -
use older windows version
0r windows 7
I have to choose the older version every time I boot up which is very annoying.
My question is does anybody know a fail safe way of removing this 'choice' so it boots straight in to XP?

I do have an XP disc but it's only XP Pro Sp 1. I downloaded Sp2 and 3 from the Microsoft website and put them on a CD.

Audrey
 

A:Dual booting problem-XP and windows 7

Read other 10 answers
RELEVANCY SCORE 52.4

Hi guys

I have a big problem since 9/9 and I just can`t fix it.
I have a dual boot system and use Windows 8 as my main OS and on the other ssd I have ubuntu 12.10 installed.

My issue started because I completely forgot that I had ubuntu installed on the other ssd (didn`t use it anyway) and tried to raid the ssd...so now I can`t boot anything and I do need to restore my w8.

I have a usb recovery disk which allows me to use cmd but I don`t know how to use to recover my W8 so that`s why I am here.

I ran diskpart on cmd it it shows both disks and both are ONLINE.
Ran chkdsk /f but i keep getting an error and chkdsk does not run

I have asus P8Z77-V LX UEFI Mobo
Intel rapid Smart technology (RST), Intel Smart Connect Technoly is disabled.
CSM is ENABLED ( it was AUTO) and boot device control to UEFI and LEGACY OpROM.

Secure Boot is disabled and I changed the OS type to OTHER OS and also tried WINDOWS UEFI MODE.
The setup mode is EZ MODE.

Please can someone help me to get my W8 working

Thanks

A:DUAL BOOT - Windows 8 not booting

Set you bios to UEFI defaults and follow the instructions in your mobo manual for creating a raid set and configuring the associated raid options. Now, if you "tried all that already", then consider just changing you sata mode to ahci and do the install to a single drive just to get you up and running. You manual offers clear and concise instructions on how to do all of the above. Download the manual here:

https://www.asus.com/Motherboards/P8...rt_Download_36

Read other 7 answers
RELEVANCY SCORE 52.4

Hello All,
I wasn't sure wther to post in the vista forum or the NT workstation forum but as the current OS I am using is Vista I will post in this.
I was wondering if it was possible to dual boot Windows NT 4.0 Workstation with Windows Vista (Windows Vista being the current OS, which is one of the problems as it blocks me running setup). I tried running setup in safe mode which it let me do, it then copied files needed to install to the hard drive, and when it restarted nothing came up and vista booted as normal.

Any Ideas, or is it not even possible and am I wasting my time LOL.

Thanks :)

A:Dual Booting Windows NT 4.0 Workstation...

Hello luke,

Not sure that would be worth the time or effort.

As the system is running Vista now probably isn't gonna run with NT4. Different hardware

requirements and not gonna find the drivers.

You can't run the install from within Windows. You would need to boot to the cd to run

the setup process. Depending on the disk that you have you will need the setup floppies

Also earlier version of windows will need to be installed first and then later version .

So IMO this would be a waste of time to even attempt. Not saying that it will even work.

Just my thoughts on it.

Read other 2 answers
RELEVANCY SCORE 52.4

Hello,
Sorry if this is not in the correct section, I just didn't really know what to put it. A year ago I installed windows 7 and XP (Dualboot) and now I want to remove XP because I stop using completely (for the last 8 months). The problem is that my hard drive is partitioned into 3 sectors (Windows XP/Windows 7/ SOFTWARE). Anyone know how i can format the XP sector or delete it? When I try to remove folders from the XP sect while I am in 7, it gives me errors, and I've tried to format it while in 7 and it doesn't work. Any Ideas on what I can do?
Thanks for the Help

A:Dual Booting Windows XP and 7, Want to remove XP

when you setup the dual boot what order did you install the os?

Read other 8 answers
RELEVANCY SCORE 52.4

Okay everybody, this is basically a 'multi' thread. Anyway, I'm considering buying an XP installation CD/license. Are these still available? And if so, what's the price? And also, how would I go on about dual booting? I heard you have to shrink your partition to fit the XP installation on (because I only have one hard drive). Is there a tutorial that tells you? Sorry if this all sounds a bit newbish, but I'm not too experienced with this part of computing even though I reformatted my PC about 3 times :0
Thanks in advance!

A:2 in 1: Dual booting XP with Windows 7 And how much does XP cost?

  
Quote: Originally Posted by gln2d3


Okay everybody, this is basically a 'multi' thread. Anyway, I'm considering buying an XP installation CD/license. Are these still available? And if so, what's the price? And also, how would I go on about dual booting? I heard you have to shrink your partition to fit the XP installation on (because I only have one hard drive). Is there a tutorial that tells you? Sorry if this all sounds a bit newbish, but I'm not too experienced with this part of computing even though I reformatted my PC about 3 times :0
Thanks in advance!


Hi gln2d3, start here with the tutorial Dual Boot Installation with Windows 7 and XP the cost of XP can vary depending on the flavour (basic, home, pro) Ebay can be good but be wary !

Read other 9 answers
RELEVANCY SCORE 52.4

My Specs. Built newsystem last weekend and everything is BRAND NEW!!

1 SATA Western Digital Caviar 500GB HD 16 MB Cache
1 SATA Western Digital caviar 750GB HD 32 MB Cache
Athlon 955 Black Quad Core 3.2 MH
8 GB RAM
ASUS MB
GeoForce 9400 GT Video
Windows 7 Home Premium Family Pack Upgrade (3 licenses)

Background: I use my computer for 2 reasons. One is for general (internet, MS office, etc...) The other is for serious Digital Audio recording using Cakewalk Sonar and 100's of plugins and effects. My xp systems I have always dual booted xp with xp. One for fun and one for music. XP system for music was tweaked and optimized for music (no internet, no email etc.)

My Problem. I bought the Family pack (3 Pc's) upgrade knowing that I would install at least 2 versions of Win 7 on my computer.

My first installation (Sunday) went fine and was installed on the 500 GB HD. Startup was fast. On Monday night I bought another HD (750 GB) and installed another version of Win 7 on the new harddrive for my music stuff. It was working fine. 2 new versions of Win 7 on new brand new sepatate HD's.

Yesterday (Tuesday), I got home and booted up to Win 7 Music system and was told to run chkdsk which it does and noticed the startup was much slower once it rebooted. So I try to install some of my music programs and I get an error that the file system is now corrupt. I cannot install programs or even copy things from another drive to that partition. When I tried to install programs another ... Read more

A:Dual Booting with 2 Windows 7 OS on same computer

Hello Tracy, welcome to Seven Forums
I have installed W7 on 2 partition on the same drive on my PC.
I haven't run into this problem.
Have you performed a repair Install?
When you get home from work, maybe have a look at event viewer and upload any relevant logs you find.
It might be worth running chkdsk on the drive too.

Read other 1 answers
RELEVANCY SCORE 52.4

I have Windows 10 installed on HD1 (Samsung) and working will.
I had a second HD2 (WD) with Win7 installed for a dual boot operation.
For some reason, I could never successfully boot into Win7. Out of frustration I decided to format the Win7 drive and start over.

The problem now is I cannot install Win7 on the HD2 drive. When I choose F12 on boot up and select the WD disk, a screen appears saying "Windows Boot Manager" It instructs me to insert my Win7 install disk an reboot.

Next steps:
I insert the Win7 install disk and reboot using F12 to select the WD disk.
The "Windows Boot Manager" screen appears again with the same instructions as above!
If I reboot again and do nothing, the system will boot to Windows 10.
My question, how to install Win7 on the WD disk and then setup a dual boot operation?

Help is greatly appreciated.

Jim

A:How to install Win 7 on a second HD for dual booting with Windows 10 ?

Originally Posted by jim1931


I have Windows 10 installed on HD1 (Samsung) and working will.
I had a second HD2 (WD) with Win7 installed for a dual boot operation.
For some reason, I could never successfully boot into Win7. Out of frustration I decided to format the Win7 drive and start over.

The problem now is I cannot install Win7 on the HD2 drive. When I choose F12 on boot up and select the WD disk, a screen appears saying "Windows Boot Manager" It instructs me to insert my Win7 install disk an reboot.



Next steps:
I insert the Win7 install disk and reboot using F12 to select the WD disk.
The "Windows Boot Manager" screen appears again with the same instructions as above!
If I reboot again and do nothing, the system will boot to Windows 10.
My question, how to install Win7 on the WD disk and then setup a dual boot operation?

Help is greatly appreciated.

Jim



Hi there.

is the HD2 a GPT drive -- I think W7 can't boot to a GPT formatted drive but can of course use them. If I'm wrong on this (I don't dual boot any more --preferring to use VM's or simply slide a HDD caddy into one of my bays on a microserver) I'm sure there's some sort of restriction with GPT and W7 --maybe the GPT HDD has to be the first one.

If I'm 100% wrong here - then please ignore - but I do remember something in the past about W7 and booting from GPT HDD's.

Cheers
jimbo

Read other answers
RELEVANCY SCORE 52.4

Hey,

I'm trying to dual boot Windows XP Pro 32-bit and Windows 7 with Windows 7 installed first; but this isn't the problem.

The problem is trying to boot Windows XP so it can install. I booted XP from an installation CD, then a blue setup screen appears, with some files apparently being loaded at the bottom of the screen (this is around the time pressing F6 to load drivers comes up). Then boom, I get blue screened with this error and cannot proceed:

A problem has been detected and windows has been shut down to prevent damage to your computer.

If this is the first time you've seen this Stop error screen, restart your computer. If this screen appears again, follow these steps:

Check to be sure you have adequate disk space. If a driver is identified in the Stop message, disable the driver or check with the manufacturer for driver updates. Try chaging video adapters.

Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as caching or shadowing. If you need to use Safe Mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode.

Technical Information:

*** STOP: 0x0000007E

I've been driving myself crazy trying to come up with a solution. My theory so far is that my SATA HDD can't be recognized by the Windows XP installation CD, therefore I need to add driver files to the CD (somehow?) so that they're compatible.

I have a:
Intel(R) PCHM SA... Read more

A:Dual booting, Windows XP and SATA

Read other 16 answers
RELEVANCY SCORE 52.4

Hello,

I have a 2nd unused SSD that I would like to install Windows 8 on to. I already have Windows 7 on another SSD.

Is it as simple as fresh installing as normal on to the other unused SSD? then I can have a choice to dual boot to Windows 8 instead??

Thank you, all help is highly appreciated!

A:Windows 8 dual booting question

Simple answer is yes.

BTW, Welcome to the Eight Forums. . .

Read other 4 answers
RELEVANCY SCORE 52.4

I Have a CPU it was Windows 7 Home Premium installed , i Got windows 8 downloaded from Microsoft . I installed it without a CD . I Extracted the .iso file and Just Click Setup.exe , it was really slow so i left it at my house , when i ome Home it enters windows 8 Home Screen . I am really confused , i thinks its gonna ask me Custom or Upgrade but when I'm home it just ask me what color do you want for your theme . I Inserted the windows 7 CD and Installed on drive B: ( B is a hard disk i made with diskmngmnt.exe ) and it boots to windows 7 , i want to shut down my CPU . I turned it back On ( Restart ) and it just shows me a black screen . Any help Please ?? ASAP

A:Windows 8&7 Dual Booting Won't Start-up

oh man... tell me why did you really install window 7 ? windows 8 installation was completed and it was just asking how to personalize... try startup repair with your win7 DVD(do it 3-4 times separately, with a restart between each repair time )... and also boot into windows 8 and turn off fast startup.
hope it helps.

Read other 4 answers