Over 1 million tech questions and answers.

Alenware Aurora Front door connector/PSU issues

Q: Alenware Aurora Front door connector/PSU issues

Recently Swapped out my old enermax PSU for a new one. Plugged everything back in. I inadvertenly disconnected a a twin wire two prong cable which connects to the hinge of thefront door of the tower. It is tied into the other connectors for the system pannel(20 pin) connector on the motherboard. However i do not know where it plugs in?

I would not normally care but the PC will not power up with the new PSU. All i am getting is the standby power LED on the motherboard to light up. I have connected the two fans to the same cables as the EZ_plug( which i just use a ordinary four prong connector). The DVD and CD-R drives use the same power cable. The HDD i have using a SATA power connector. Finally the floppy drive just uses a standard connector with nothing else on the other 12v connectors. The motherboard uses a ATX connector, EZ_plug and 24 pin connector.
I just realised i connedted the PSU up incorrectly. I used an EZ_plug with the ATX connection which i should not do with a Geforce 7800 GT on Asus A8N-SLI Deluxe(ez-plug should only be used with two cards). I also forgot to connect the six prong connector on the video card. Would this earlier omission on my part have damaged the mobo? I rectified and still no change?

RELEVANCY SCORE 200
Preferred Solution: Alenware Aurora Front door connector/PSU issues

I recommend downloading and running Reimage. It's a computer repair tool that has been proven to identify and fix many Windows problems with a high level of success.

I've used it in the past to identify and fix everything from blue screens (BSOD's), ActiveX errors, corrupt files and processes, dll/exe/sys errors, recover lost memory, Windows update problems, defragging, malware removal etc.

You can download it direct from this link http://downloadreimage.com/download.php. (This link will automatically start a download of Reimage that you can save to your computer.)

A: Alenware Aurora Front door connector/PSU issues

The connector is for LED which can be installed in the door. I twisted ALienware's arm to answer this. On rechecking my system connection panel, i discovered my pwr switch connect was wrongly connected into the wrong slot(my fault)!I installed a new hard drive as well and my system now appears fixed and stable. I am hoping the inital problems with with system resets, usb connections and damaged file segments on HDD were to do with either the PSU or HDD. I hope the mobo is unaffected( i hope so the warranty ends in january). Any suggestions to ascertain if i need to check anything else would be helpful?

Read other 1 answers
RELEVANCY SCORE 98

Recently Swapped out my old enermax PSU for a new one. Plugged everything back in. I inadvertenly disconnected a a twin wire two prong cable which connects to the hinge of the front door of the Tower. It is tied into the other connectors for the system pannel(20 pin) connector on the motherboard. However i do not know where it plugs in?

I would not normally care but the PC will not power up with the new PSU. All i am getting is the standby power LED on the motherboard to light up. I have connected the two fans to the same cables as the EZ_plug( which i just use a ordinary four prong connector). The DVD and CD-R drives use the same power cable. The HDD i have using a SATA power connector. Finally the floppy drive just uses a standard connector with nothing else on the other 12v connectors. The motherboard uses a ATX connector, EZ_plug and 24 pin connector.

I just realised i connedted the PSU up incorrectly. I used an EZ_plug with the ATX connection which i should not do with a Geforce 7800 GT on Asus A8N-SLI Deluxe(ez-plug should only be used with two cards?). I also forgot to connect the six prong connector on the video card. Would this earlier omission on my part have damaged the mobo? I rectified and still no change?
 

A:Strange Connector on Alienware Aurora Door

That 2-pin plug is probably 5 volts gonig to LEDs in the door. Carefully go over the motherboards manual and recheck all the power supply connections to it. If all else fails, take the system down to the bare minimum, no sound card, no video card and only one memory stick and see if it powers up. Try resetting the CMOS while you are at it
 

Read other 4 answers
RELEVANCY SCORE 62.8

i have a thermaltake tsunami case, and for some reason the lights that are on the door keep flickering and sometimes staying off until i restart my computer. my specs are below in green. in the case i have 2 120mm fans, 1 80mm fan and the heastink fan. one of the fans has led lights on them. for a psu i have a 550W antec trupower 2.0. everything else runs fine so i dont think it could be a psu problem. anyone know what the problem is?
 

A:thermaltake tsnunami case, front door lights

Read other 6 answers
RELEVANCY SCORE 62

Received a new Dell desktop unit and the Front Door I/O Plastic Bezel/Cover was loose in the box and not attached. Flexing the plastic door to attach to the two connection points is easy enough, but there is a small spring that needs to attach, presumably to keep the door closed when not in use. There is a small hole on the connection point of the door itself where one end of the spring goes, but I'm not able to figure out where to attach/place the other end so that the spring will work. Suggestions welcomed.

Thanks.
 

Read other answers
RELEVANCY SCORE 60.8

How to connect usb front connector on the Mother Board, have +vcc, +d,
-d, and ground.

Thanks!!
 

A:front usb connector

This would depend on your motherboard, if you dont have the manual, download it from the mfg web site, and it should tell you how to connect them.

Here's a pretty good tutorial I found that explains it. It's probably not exactly as your setup but it should be close enough for you to get a good idea of what to do. I think you are probably interested in the "Front USB via a Port to Header connection" section.

Good luck.
 

Read other 1 answers
RELEVANCY SCORE 60.4

I have just changed my system from a large case to a matx case, but used all the part except the mainboard. Changed from a Asus P6T Deluxe to a Asus Rampage Gene II.

Now I thought I might have to reinstall windows, but as luck would have it, it booted straight into windows with no other problem except I had to register windows.

It was only when I tried plugging in a usb memory stick into the front of the case that I got a bsod. If I plug it into one of the back usb ports it works. So I checked to see if the cable was attached correctly on the internal header and again it was.

So could this be down to windows or a hardware problem?

A:Front usb connector problem

It is a hardware problem ! Sometimes the front usb ports does not work properly.

Read other 6 answers
RELEVANCY SCORE 60.4

Hello
I have attached an image of my cabinet, i have front usb & two covered hole (selected with red line in the image) besides it. I think they are front audio but it has no wire from inside. please have a look at it & let me know if i can make it a front audio connector.
thanx
 

A:Front audio connector

Read other 16 answers
RELEVANCY SCORE 59.6

I have the mothermoard that comes with the TinkCentre E93 Desktop and I have since upgraded my computer case to something bigger and better looking. I managed to get everything connected besides the front panel connectors which are very important. The ThinkCentre motherboard is a bit weird in its layout and the ThinkCentre case had a single connector that connects into this pinout however, my new case has single connectors instead of a single 13 pin + 1 blank connector. My case has a connector which consists of a total of 9 pins.It would've been simple if the board had a marking indicating what each pinout is for and which is positive and negative but unfortunately there isn't any of  that. At the moment I can't seem to find any information at all with regard to how I should connect this. I would like to get opinions with regards to which pin goes where. This is the full specs of the desktop  

Read other answers
RELEVANCY SCORE 59.6

My motherboard is a model Ms-6330 Ver: 2.1 (Microstar) but it also has the gateway part number 2512595. I am currently relocating this motherboard to a brand new case that I just bought and I ran into a problem. The front panel connectors (power switch, led, hdd led, etc) go onto the motherboard in a certain area where there are 15 pins. Unfortunately I have no idea which connectors connect to which pins. Can someone help me? (Maybe someone with the same motherboard/problem). All I need is a way to identify the pins and make sure I don't like accidently fry my motherboard. Thanks a lot! -Andrew C.
 

A:Front Panel Connector on Mobo

Hi,
For starters, have you checked your manual? Also, look on the m/b...in really tiny abbreviated letters you should be able to see where these go (you may see "pw switch"...."HDD ACT"........i know when i was installing my connectors, i got most of them wrong..but dont worry..no frying of the motherboard.....if the connector is in the right place but no light from the LED..try reversing the cable........the easiest cables to place are the pw switch and the reset..as you can test these easily....good luck
 

Read other 3 answers
RELEVANCY SCORE 59.6

I'm assuming these are not USB 3.0 ports but what kind of USB bracket plugs would work here?  

Read other answers
RELEVANCY SCORE 59.6

What is the order of connection of the pin numbers for the front panel connector.

Eg: what number pin for the power switch etc.

This is for a E-machine D2685 mother board that i have recently purchased.
 

A:e-machine front panel connector

According to my eMachine files the D2685 has a FIC VC37GV Mainboard and uses a Intel standard 9 pin front panel header.

Attached is a pinout for that header.
 

Read other 1 answers
RELEVANCY SCORE 59.6

Hi Guys:

It's been a while since I've posted a question, however, this one is really bugging me. Recently, I've been putting together a lot of systems that have the 9-pin front-panel connection on the motherboard. The problem for me is that the ACPI/LED has only a
2-pin and most cases come with 3-pin cables. No mater which way I input the 3-pin cable, the front-panel LED light will not come on. Does anybody know what I'm referring? If you can Be of assistance, please give me some input.

Thanks.
 

A:Motherboard 9-Pin Front-Panel Connector

If the motherboard requires a 2 pin connector and the case manufacturer supplies a 3 pin connector just take the pins out of the connector and place them next to one another in the connector. There is a little tab on the connector you can lift up and slide the pin out. It's hard to explain here, but once you look at it closely you will see what I mean.
 

Read other 2 answers
RELEVANCY SCORE 59.6

I just put in a Soyo P4I865PE Plus Dragon 2 into a POWMAX case. I had another Soyo Dragon P4X400-8235 mobo that had fried, and I'm replacing it.
What the mobo connector pins for the front panel require are the HDD LED, ACPI LED, PWRBT, RESET, POWER LED, KEY LOCK, SPEAKER.

My case has the SPEAKER, THE RESET, and the HDD LED, plus a POWER SW, and
one cable with
mic-bias
spkout r
spkout l
Return R
Return L

and 2 cables each with
+vcc
+D
-D
grounds.

So I have the SPEAKER, THE HDD LED and the RESET pins connected.

Right now I'm not getting any power. I suspect that it's because the POWER LED hasn't been hooked up. I don't know if hooking the POWER SW to the POWER LED will do any good--or any harm. Any suggestions, or do I need a different case?

Thanks for any suggestions, tips, or answers.
 

A:Front Panel Connector Pins

Read other 11 answers
RELEVANCY SCORE 58.8

Hello! Recently, I transferred my Dell Motherboard (From an Inspiron 560) to a new Rosewill Challenger-S case. All of that went fine and dandy but now I'm facing another problem: I don't quite know where to plug up the cables from the case's front panel (power switch, reset switch, HDD LED). I found a port on my motherboard labeled "Front Panel" which matches the ports, but one is missing like normal front panel connectors, and the cables only take up 6 out of the 9 pins. So the real question is, where do you plug up the cables, or do you even put them in that spot?


Sorry if that sounded really nooby,
JaxDrumm

A:Help with Front Panel/Power Button Connector

Take a close up picture of your motherboard and post it so we can see it. please.

Read other 1 answers
RELEVANCY SCORE 58.8

So I basically have a very odd front panel audio connector setup, very confusing, I've made over 10 thread on different forums and non were able to help me.

I'm using a Gigabyte G31 motherboard GIGABYTE - Motherboard - Socket 775 - GA-G31M-ES2L (rev. 1.x)

Manual page for the motherboard output can be found below the first image

The front panel audio connectors consists of:
Yellow- MIC BIAS
Green - SPKOUT R
Peach - MIC In
Blue - Return L
Black - Ground
White - SPKOUT L
Grey - SPKOUT L

Much Thanks and appreciation to those who read this read

A:Front Panel Audio connector help needed

Your front panel connections aren't odd, but they are old. They are for the AC97 standard.

Set your onbaord audio to AC97 in the BIOS set-up.

The AC97 pinouts are here:

Desktop Boards — Front panel audio header pinouts

1 Mic In
2 Ground
3 Mic Bias
5 Spkout R
9 Spkout L

It looks like the onboard audio doesn't support the Return lines.

There should only be one Spkout L connector. It's the white (not gray) one.

Have you really been trying to figure this out for 5 months? Yikes.

If these connections cause your PC to go up in a fireball, don't blame me.

Read other 1 answers
RELEVANCY SCORE 58.8

Hi everyoneWhile I took the front panel off of my case the other day I accidently removed the JAUD1 jumpers....and now my sound doesn't work. I downloaded the specific instruction guide from MSI for my motherboard and here's the section for it:The two right sound in and out cables were still attached, and I got sound out of my right speaker. But then when I connected the rest to what I thought was correct, I got sound out of my left speaker only. EDIT: I tried not attaching any of the cables and then I get no sound.The problem I have with these directions is that the cables are not labeled the same as the diagram. They are as follows:Purple - R INYellow - R OUTBlack - GNDGreen - MIC BIASBlue - L INRed - L OUTBlack - GNDOrange - MIC INCan anyone help with this? I'd love to have both of my speakers playing sound again....

Read other answers
RELEVANCY SCORE 58.8

I am attempting to transfer the motherboard of my h50-50 to a different case.  I am doing this in order to make room for a much larger video card and psu that simply will not fit in the Lenovo case.  I have run into a bit of difficulty with the 'Front panel connector'.  If you look in the 'Lenovo H50 SeriesHardware Maintenance Manual' it is on page 28 (Lenovo H50-50).  I have been trying to find the specs on what each pin is for but have been unable to find such information.  Could someone please direct me to where I can find such information or could you please provide me with the details?  Specifically I am looking for the power switch pin(s), hdd activity pin(s) etc. thanks

A:H50-50 motherboard Front panel connector pin layout

Welcome to the Lenovo Community !
 
There is no documentation that I am aware of that show the pinouts of the various connectors on your motherboard.  I would just use an Ohm meter on your old H50-50 case and trace wires on the old front panel plug.  Once you know how the old plug was configured you will know the pin assignments on the motherboard. 

Read other 2 answers
RELEVANCY SCORE 58.8

Pavilion 500-205t originally came with Win 7 64 bit home,  upgraded last year to Win 10 anniversary edition 64 bit. Ser # 2MD4060X7W.  I am having trouble with the SS USB connectors on the Front of my Pavilion 500-205t.  I have to wiggle the flash drive or phone connector to get the computer to recognize what is attached and it frequently cuts in and out when in use.  The flash drive and phone connector work perfectly on my other HP Desktop. I have checked the wires and found that it is wired directly in the back of the connector and it attaches to the circuit board. I beleive the connectors have been damaged. Is a replacement part available, and if so:    1 . What is the part number    2. Where can I get it    3. How much does it cost. Thank You

A:Need replacement USB connector assembly for front of Pavili...

@blpen,Here is an example of the part, price, and part number.another

Read other 1 answers
RELEVANCY SCORE 58.4

My motherboard USB connector is not compatible with my case front panel USB plugs. The USB connector on my motherboard (NetVista A22p 2292) is for one 10 (two rows) pin connector. The plugs on the tower (A-Top XBlade Black/Silver Ultimate Gaming Machine With 450W PSU & Side window, Model "AT859A-BK") front USB are two separate 4 pin USB plugs (They are VCC, USB1-, USB2+, GND pins w/GRN wire). What can I get or do to make them compatible? Thanks.

A:USB connector not compatible with case front panel USB plugs

See if this helps..not exactly sure if it will:http://www.ramelectronics.net/html/usb_adapter.html

Read other 1 answers
RELEVANCY SCORE 58.4

Hi, I just purchased a Gigabyte UD3R motherboard. My computer case is at least 6 years old (don't know make) and many of the connectors don't match description to motherboard.

Cables for Audio:

RETURN L (Blue)

RETURN R (White)

SPKOUT L (White)

SPKOUT R (Green)

GROUND (Black)

MIC BIAS (Yellow)

MIC-IN (Pink)
My case doesn't provide an HD audio module so I need to set it up for AC'97 functionality. The pin set up is as follows
Pin 1 - MIC

Pin 2 - GND

Pin 3 - MIC Power

Pin 4 - NC

Pin 5 - Line Out (R)

Pin 6 - NC

Pin 7 - NC

Pin 8 - No Pin

Pin 9 - Line Out (L)

Pin 10 - NC
Really appreciate the help. Thanks!
 

A:Solved: New Motherboard + Front Panel Connector Confusion

Most probably should work by:
MIC-IN to pin 1,
MIC BIAS to pin 3,
GROUND to pin 2,
SPKOUT R to pin 5,
RETURN R to pin 6,
SPKOUT L to pin 9,
RETURN L to pin 10.

Please don't mark threads solved if they aren't, less people will wander to the thread if it looks like no further help is needed.
 

Read other 1 answers
RELEVANCY SCORE 58.4

I have a p4SD-LE Asus MB (Same as P4G800V retail) That has an undocumented Front Headphone jumper near the black CD-IN connector (behind the PCI slots). I would like to use it to hook up the front pannel headphones but can not find any documentation on it. Anyone have any info?

Thanks in advance
 

A:p4g800-V or p4SD-LE Front Pannel headphone connector

Hello and welcome to Techspot.

I can`t find any info on a jumper either. The only manual I could seem to find was in Japanese lol

All I can find is a aux connector next to the cd-in connector.

Regards Howard :wave: :wave:
 

Read other 1 answers
RELEVANCY SCORE 58.4

Motherboard Front Panel connectors Zeus 60 R1 07G Samsung.
Pls send a picture of the panel or tell me which color wires to which one

Power button , HDD , LED Display





 

Read other answers
RELEVANCY SCORE 58.4

I recently tried to upgrade my mother board in my pc. The factory motherboard has a 14 pin front panel connector and the new motherboard has a 10 pin front panel connector. I had the bright idea of tinkering with the wires and rearranging them to fit the 10 pin input. I am currently trying to put all the original parts back together and the wires are still set up for the 10 pin connector and not the 14. Could anyone help me figure out which postions to put the wires in on the connector?


























IMG_4343.JPG ?1633 KB

A:Lenovo IdeaCentre K220 Front Panel Connector

Picture of the wires that go into the connector


























IMG_4345.JPG ?988 KB

Read other 1 answers
RELEVANCY SCORE 58.4

I need the Layup front panel connector HP Pavilion P7-1207c desktop pc

Read other answers
RELEVANCY SCORE 58.4

I'm looking at the layout of this connector

Read other answers
RELEVANCY SCORE 57.6

I need to know about the layout of the io pins.

Read other answers
RELEVANCY SCORE 57.6

HiI am trying to determine which type of 3.5mm audio plug to put into the front panel connector for using headphone with a microphone to do video communications. could be - sleeve, ring and tip (mono sound and microphone)orcould be - sleeve, ring, ring, and tip (stereo sound and microphone) Have read through the manuals and nothing is said about which type to use.

A:Front panel audio connector - what plug type to use for head...

Hi, I can't see your image but probably you can see mine   (a) All standard 3.5mm (stereo) headphones will fit and work.(b) For the second port on the right, all standard 3.5mm headsets will fit and work. Its default is for microphone, all standard 3.5mm mono microphones will fit and work. Note: probably around 95% of 3.5mm headphones and microphones on the market now are normal/standard. Regards.

Read other 1 answers
RELEVANCY SCORE 57.6

What is the layout on the motherboard for the front panel LED connectors?  The XPS 9000 manual does not specify that at all.  The motherboard itself is model number 0X501H, as given by CPU-Z.

Is the layout the same as the one listed in this thread below regarding the XPS 8500?

en.community.dell.com/.../19586001

Read other answers
RELEVANCY SCORE 57.6

I found a lot of people searching for this information... since I was unable to find it, I tested the front panel connectors by myself, and that is what I found:
 
Power front panel (black connector)
 
+----+----+----+----+----+----+----+
| Bk | | | | | | |
+----+----+----+----+----+----+----+
| Yl | | Bk | Gn | Yl | Bk |xxxx|
+----+----+----+----+----+----+----+

+----+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 | 13 |
+----+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 | 12 |xxxx|
+----+----+----+----+----+----+----+

Description

1 Black Disk activiry led ground
2 Yellow Disk activiry led ground
3 Not connected
4 Not connected
5 Not connected
6 Black Power led ground
7 Not connected
8 Yellow Power led signal
9 Not connected
10 Yellow Power switch signal
11 Not connected
12 Black Power switch ground
13 Not connected
14 Locked (no pin)
USB front panel (yellow connector)
 
It's a standard internal USB connector, but with two additional ground wires
 
+----+----+----+----+----+----+
| Bk | Re | Wh | Gn | Bk | |
+----+----+----+----+----+----+
| Bk | Bw | Bl | Yl | Bk |XXXX|
+----+----+----+----+----+----+

+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 |
+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 |XXXX|
+----+----+----+----+----+----+

1 Black Ground
2 Black Ground
3 Red US... Read more

A:ThinkCentre front panel connector (power, audio and USB) pinouts (A60, M58, M71, M91, M92)

OK I am intrigued.  What are you trying to accomplish ... a hibrid A60 ?





T23: 2647-8RU, Ubuntu 12.04 LTSA61E: 6418-12U, W7/Pro 64X200: 7454-CTO, W7/Pro 32

Read other 9 answers
RELEVANCY SCORE 57.6

I have Workstation xw4600 motherboard E93839 front panel connector is a 18 Pin. I cannot connect the front panel such as power switch button, reset button, HDD LED, and etc. Is there a pinout schematic for this motherboard's front pannel? I have ws ug xw4600 strg 453080-001 screen PDF that is the motherboard. Does not give the 18 Pin conector. Thank you for your time.

A:workstation xw4600 E93839 front panel connector to the mothe...

Above on the left is this specific forum's search box, and if you type in pinout and then hit return you will find what you need.  The HP workstations of this era (xw6400 xw6600 xw4600 etc) used very similar pinouts with slight variations, and there are excellent posts in there where you can see all the variations.   All the important ones will be there for you.  Even the wiring colors have been quite uniform.  Makes sense they would do it that way.

Read other 1 answers
RELEVANCY SCORE 57.6

Hello, I've recently bought an m57p (type) motherboard and I'm trying to install into a new case. But I can't find any instruction or scheme how to connect front panel cables. Can anybody explane how to connect them? I now have 13 pins and I have any ideas how to connet them correctly. Please help me...

A:ThinkCentre M57p (type 9088) front panel connector...

Refer to this thread.   Thx. 
 
ThinkCentre-front-panels-power-audio-and-USB-pinout
 
 

Read other 1 answers
RELEVANCY SCORE 57.2

Would like to move my Precision T3500 Motherboard to Another box.
The Front Panel connector might be useful, but I have not found
any documentation of this.

Is there a Motherboard manual somewhere, or at least the pin definition of the Front Panel connector?

A:Precision T3500 Motherboard documentation (Front Panel connector spec)

.As with most Dells there is a proprietary Front Panel Board and 20 pin or more ribbon cable.

Dell Precision WorkStation T3500 I/O Panel Assembly with USB Audio I/O Control Panel, 29" Internal Audio Cable D/PN X389H, Front Panel Cable D/PN JN454, and Mounting Bracket, Dell M884G, MC532.
http://www.txcesssurplus.com/servlet/the-8929/Dell-M884G-Precision-T3500/Detail

 

Read other 18 answers
RELEVANCY SCORE 57.2

I found a lot of people searching for this information... since I was unable to find it, I tested the front panel connectors by myself, and that is what I found:
 
Power front panel (black connector)
 
+----+----+----+----+----+----+----+
| Bk | | | | | | |
+----+----+----+----+----+----+----+
| Yl | | Bk | Gn | Yl | Bk |xxxx|
+----+----+----+----+----+----+----+

+----+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 | 13 |
+----+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 | 12 |xxxx|
+----+----+----+----+----+----+----+

Description

1 Black Disk activiry led ground
2 Yellow Disk activiry led ground
3 Not connected
4 Not connected
5 Not connected
6 Black Power led ground
7 Not connected
8 Yellow Power led signal
9 Not connected
10 Yellow Power switch signal
11 Not connected
12 Black Power switch ground
13 Not connected
14 Locked (no pin)
USB front panel (yellow connector)
 
It's a standard internal USB connector, but with two additional ground wires
 
+----+----+----+----+----+----+
| Bk | Re | Wh | Gn | Bk | |
+----+----+----+----+----+----+
| Bk | Bw | Bl | Yl | Bk |XXXX|
+----+----+----+----+----+----+

+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 |
+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 |XXXX|
+----+----+----+----+----+----+

1 Black Ground
2 Black Ground
3 Red US... Read more

A:ThinkCentre front panel connector (power, audio & USB) pinouts (A55, M58, M71e, M73, M91, M92, M93)

OK I am intrigued.  What are you trying to accomplish ... a hibrid A60 ?





T23: 2647-8RU, Ubuntu 12.04 LTSA61E: 6418-12U, W7/Pro 64X200: 7454-CTO, W7/Pro 32

Read other 9 answers
RELEVANCY SCORE 56.4

I found a lot of people searching for this information... since I was unable to find it, I tested the front panel connectors by myself, and that is what I found:
 
Power front panel (black connector)
 
+----+----+----+----+----+----+----+
| Bk | | | | | | |
+----+----+----+----+----+----+----+
| Yl | | Bk | Gn | Yl | Bk |xxxx|
+----+----+----+----+----+----+----+

+----+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 | 13 |
+----+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 | 12 |xxxx|
+----+----+----+----+----+----+----+

Description

1 Black Disk activiry led ground
2 Yellow Disk activiry led ground
3 Not connected
4 Not connected
5 Not connected
6 Black Power led ground
7 Not connected
8 Yellow Power led signal
9 Not connected
10 Yellow Power switch signal
11 Not connected
12 Black Power switch ground
13 Not connected
14 Locked (no pin)
USB front panel (yellow connector)
 
It's a standard internal USB connector, but with two additional ground wires
 
+----+----+----+----+----+----+
| Bk | Re | Wh | Gn | Bk | |
+----+----+----+----+----+----+
| Bk | Bw | Bl | Yl | Bk |XXXX|
+----+----+----+----+----+----+

+----+----+----+----+----+----+
| 1 | 3 | 5 | 7 | 9 | 11 |
+----+----+----+----+----+----+
| 2 | 4 | 6 | 8 | 10 |XXXX|
+----+----+----+----+----+----+

1 Black Ground
2 Black Ground
3 Red US... Read more

A:ThinkCentre front panel connector (power, audio & USB) pinout recase (M58, M71e, M73, M91, M92, M93)

OK I am intrigued.  What are you trying to accomplish ... a hibrid A60 ?





T23: 2647-8RU, Ubuntu 12.04 LTSA61E: 6418-12U, W7/Pro 64X200: 7454-CTO, W7/Pro 32

Read other 9 answers
RELEVANCY SCORE 56

When I installed a new 2.5 SATA disk in my Optiplex 5040 SFF, the front USB 2 connector with PowerShare stopped working.
When I uninstalled the disk, the front USB 2 connector with PowerShared started to work again.
Because the power supply just have one sata power-cord I used a splitter to supply the two disks with power.
According to the specifications it should be possible to use to hard disks in the Optiplex 5040 SFF.  I have just not been able to figure out how :-)
I have not been able to find a reason for this, can someplease help me :-)
/Thomas

Read other answers
RELEVANCY SCORE 52.4

I have a back door trojan virus that I can't seem to remove below is the scan I just did.
Its a windows system 32 scan that is infected. Help me please.

Run date: 2012-08-19 18:30:29
-----------------------------
18:30:29.489 OS Version: Windows x64 6.1.7601 Service Pack 1
18:30:29.489 Number of processors: 2 586 0x170A
18:30:29.489 ComputerName: OWNER-PC UserName: Owner
18:30:32.304 Initialize success
18:35:05.643 AVAST engine defs: 12081900
18:35:13.392 Disk 0 (boot) \Device\Harddisk0\DR0 -> \Device\Ide\IdeDeviceP0T0L0-0
18:35:13.392 Disk 0 Vendor: ST31000528AS CC44 Size: 953869MB BusType: 3
18:35:13.412 Disk 0 MBR read successfully
18:35:13.412 Disk 0 MBR scan
18:35:13.422 Disk 0 unknown MBR code
18:35:13.432 Disk 0 Partition 1 00 1B Hidd FAT32 NTFS 14524 MB offset 2048
18:35:13.442 Disk 0 Partition 2 80 (A) 07 HPFS/NTFS NTFS 381546 MB offset 29747200
18:35:13.462 Disk 0 Partition 3 00 07 HPFS/NTFS NTFS 557797 MB offset 811153408
18:35:13.492 Disk 0 scanning C:\Windows\system32\drivers
18:35:23.733 Service scanning
18:35:40.814 Modules scanning
18:35:40.814 Disk 0 trace - called modules:
18:35:40.834 ntoskrnl.exe CLASSPNP.SYS disk.sys ACPI.sys ataport.SYS pciide.sys PCIIDEX.SYS hal.dll atapi.sys
18:35:40.834 1 nt!IofCallDriver -> \Device\Harddisk0\DR0[0xfffffa8004538430]
18:35:40.844 3 CLASSPNP.SYS[fffff8800161743f] -> nt!IofCallDriver -> [0xfffffa80043c6580]
18:35:40.844 5 ACPI.sys[fffff88000f2d7a1] -> nt!IofCallDriver -> \Device\Ide\IdeDeviceP0... Read more

Read other answers
RELEVANCY SCORE 50

I've been having strange problems, mainly since updating to Windows 10. Sometimes, I get no response to clicking on the Windows icon bottom left corner. Other times, it has a transparent background etc. I have also been randomly getting a BSOD with IRQL_NOT_LESS_OR_EQUAL error. A link to the dump file is here...

I am running BIOS A11, GTX690, 16GB ram, i7-4820K @ 3.7GHz. Can anyone who know how to interpret dump files point me in the right direction?

Thanks.

A:Issues with Alienware Aurora R4 Windows 10

You'll probably get a better response if you re-post this in the Alienware Club forum.

Read other 1 answers
RELEVANCY SCORE 50

I have a several year old Aurora R1.  I recently pulled it out of storage and am trying to get it back up and running.  When it was last shut down and stored it was working fine.  Now that it's out of storage and running again I can't get the OS to boot.  I got it booted once, and logged into windows fine.  Tried doing some Windows Updates but they failed as well.  Went to reboot and now all I get is a black screen after the Alienware splash and post beep.  I have never run the machine on OC, have upgraded the Ram, HDD, and graphics card.  Ram was upgraded to 24GB Corsair Dominator, HDD is a Sandisk Extreme 240gb, and Graphics is a GTX 770 classified.  The other odd thing I noticed is that the RAM as it displays in the bios somehow lost 8gb.  I swapped the sticks around and now it is seeing all 24 again.  I'm trying to decide if it's the RAM or the MB at this point.  I've tried dropping the ram down to a single stick on bank 1 (4gb), with different sticks to ensure I'm not using a bad stick, but still no luck.  Running Bios version A11. 
Also, i've tried swapping the HDD around on different channels and changing the boot sequence to match.  It won't even boot from a thumb drive that is visible in the boot options list.  I must admit that my trouble shooting skills on hardware have gone downhill lately, so i'm turning to you guys for any thoughts.  Oh, the O... Read more

A:Alienware Aurora - R1- Boot issues

oh, and i just tried pulling all the HDD's and booting to see if it would error out, and nothing.  blank screen.  

Read other 3 answers
RELEVANCY SCORE 48.4

Have just installed Win 7 HP 32 bit as an u/g to a HP dv6000 series laptop with Vista HP 32 bit and Office 2007. Firstly Outlook Connector no longer connects (either wired or unwired) saying that I have no network connection although I am simultaneously connected to a Google web page. I've uninstalled/reinstalled/repaired Outlook Connector but to no avail.

I have a similar problem with HP Update which also stalls and advises "No internet connection" when I'm again simultaneously live with another webpage. I have tried with and without other web pages being open but it makes no difference.


As for HP I understand that although the dv6000 series specs are acceptable for Win 7, HP is not providing Win 7 support, so that cud be an explanation for the HP Update problem. However, I have seen threads on other forums about network/internet connectivity issues with Win 7.

Any thoughts will be appreciated

Pedro

A:Win 7 & Outlook Connector & HP Update issues

i think your probably right about why hp update isn't working but it isn't needed anyway,are you using the latest outlook connector? http://www.microsoft.com/downloads/e...DisplayLang=en

Read other 3 answers
RELEVANCY SCORE 48.4

Hi,

I'm using Windows XP on my Acer Aspire One netbook, Microsoft Outlook 2007, and Outlook Connector so that I can access my Hotmail account. I can access and refresh my mail and my contacts but not my calendar. I receive a 80004002 error indicating that my calendar synchronization failed. What I can't understand is that Outlook connector works flawlessly on my other pc notebook, which is a Sony VAIO. The email setup on both computers is identical, and of course they're both trying to access the same Windows Live Hotmail account. Could there be a setting or a missing file on my netbook that is preventing calendar synchronization?
 

A:Outlook Connector Calendar Issues

Finally! I found someone with almost the exact same issue as me!!!

I am also using Windows XP on my Acer Aspire One netbook (D250). But I have Microsoft Outlook 2003, not 2007, with Outlook Hotmail Connector 14 to access my live.com account. I too can access and refresh my mail and my contacts on my netbook, but not my calendar where I receive the following Detailed Report under Server Status:

Outlook Hotmail Connector Version 14.0.5117.5000
Account: [email protected]
Signed in successfully at 10/7/2010 6:31:11 PM.
Mail: Last successfully refreshed at 6:31 PM.
Calendar: Error at 6:31 PM.
Contacts: Last successfully refreshed at 6:31 PM.
Errors :
Time: 10/7/2010 6:31:12 PM
Error in Calendar
Synchronization error.
Time: 10/7/2010 6:31:12 PM
Error in Mail
Error with Send/Receive.
Look for a log in the Sync Issues folder.

The log in the Sync Issues folder basically says the error is the following lines in red:

19:12:42 Synchronization error.
19:12:42 Folder Collection Sync Key: 0{2ea38726-8bbb-4a84-9473-3eb208c58616}194
19:12:42 Message Collection Sync Key: 0{61df8ee1-9a1a-4e03-a7de-6ccba8554443}193
19:12:42 Error with Send/Receive.
19:12:42 There was an error synchronizing your folder hierarchy. Error : 80004002.

I have searched the internet for solutions to the above problem but have not found a thing about it. I have the following similarities as lacon’s post above however but am still unable to find any similar situations on the internet: In addition to my... Read more

Read other 1 answers
RELEVANCY SCORE 48

I have a fair amount of computer experience, if someone could please analyze this for me and suggest what steps I should take. I think I have a trojan virus, and virutal bouncer is downloaded on my computer though I have removed it previously and I am also getting a lot of popup adds from aurora. Please let me know what I can do to fix it. Enclosed is the logfile from Hijack this. Thank you so much for your assistance.
[email protected]
Logfile of HijackThis v1.99.1
Scan saved at 6:04:08 PM, on 7/6/2005
Platform: Windows XP SP2 (WinNT 5.01.2600)
MSIE: Internet Explorer v6.00 SP2 (6.00.2900.2180)

Running processes:
C:\WINDOWS\System32\smss.exe
C:\WINDOWS\system32\winlogon.exe
C:\WINDOWS\system32\services.exe
C:\WINDOWS\system32\lsass.exe
C:\WINDOWS\system32\svchost.exe
C:\WINDOWS\System32\svchost.exe
C:\Program Files\Common Files\Symantec Shared\ccSetMgr.exe
C:\Program Files\Common Files\Symantec Shared\SNDSrvc.exe
C:\Program Files\Common Files\Symantec Shared\SPBBC\SPBBCSvc.exe
C:\WINDOWS\system32\rundll32.exe
C:\Program Files\Common Files\Symantec Shared\ccEvtMgr.exe
C:\WINDOWS\system32\LEXBCES.EXE
C:\WINDOWS\system32\spoolsv.exe
C:\WINDOWS\system32\LEXPPS.EXE
C:\WINDOWS\Explorer.exe
C:\WINDOWS\System32\00THotkey.exe
C:\WINDOWS\System32\igfxtray.exe
C:\WINDOWS\System32\hkcmd.exe
C:\Program Files\Analog Devices\SoundMAX\PmProxy.exe
C:\Program Files\ltmoh\Ltmoh.exe
C:\WINDOWS\AGRSMMSG.exe
C:\Program Files\Apoint2K\Apoint.exe
C:\WINDOWS\system32\TFNF5.exe
C:\WINDOWS\sys... Read more

A:Solved: Help me please....HJT file inclosed, aurora, virtual bouncer and trojan issues!

Read other 16 answers
RELEVANCY SCORE 48

Dell Optiplex GX280 (Small Desktop design), running on XP
The problem SEEMS to be the P6 power connector (4 wires: 2 yellow, 2 black). Label on motherboard says: 12V power connector.

Here is what's going on:
*Solid amber light is on (inside the computer & on the board; stdby pwr) when main power supply is connected
*Individual capacitors look clean and in fine condition
*Plugged in w/o monitor plugged in (connector plugged & monitor unplugged) = doesn’t boot, CPU fan spins fast.
*Plugged in w/monitor plugged in (connector plugged & monitor plugged) = doesn’t boot, CPU fan spins fast.
*Unplugged w/o monitor plugged in (connector unplugged & monitor unplugged) = boots, but no signal to monitor.
*Unplugged w/ monitor plugged in (connector unplugged & monitor plugged) = boots, but no signal to monitor.

*Monitor actually reads "No Signal" when plugged to computer, but P6 connector is unplugged.

*I have already: checked the RAM, the processor, the fans - eveything else seems just fine.
Please help me figure out the solution. Thanks.
 

A:Hardware - power supply connector issues

Read other 7 answers
RELEVANCY SCORE 47.2

hi i have a e-machine EL1200-6H that i am converting from Vista home to WHS and all is fine but the NVIDIA NForce Networking Controller and i tried to find the compatible drivers online and had no success. If you know more of the compatibility of the network adapter pls let me know if ther is a way to fix.

P.S. its a on board adapter
 

A:Windows Home Server Network Connector Issues PLS HELP!!!!!!

Read other 8 answers
RELEVANCY SCORE 46.8

Hello all-

I did a search and read through others issues regarding this and tried some of the solutions with no luck. I just purchased a case with the front audio and mic ports and hooked it onto my motherboard (wondered why I was missing the power pin/connector from the case).
No luck then I realized I still had my PCI sound card still on my board so I removed it and tried again. Still no luck.
I disconnected the wires and tried rear audio to make sure the onboard sound was working, and it was.
So then I reconnected the wires but left off the rear audio pins and when I boot up I now have sound but after a minute or so I lose it.
I went to device manager and uninstalled Realtek 97 Audio and let it reinstall after boot up and I had sound until I shut down my comp for the night. Now I am back and again sound at boot up then it cuts out.
I have updated the driver as well.
Other things in my sound portion of device manager that I didnt know if I should uninstall or not are as follows:
-Audio Codecs
-Legacy Audio Drivers
-Media Control Devices
-Standard Game Port
-Video Codecs
I am wondering if there is something possibly conflicting from having a soundcard on the m/b and I need to change a setting? or if I am just one of those unlucky ones where I will not be able to get this to work.

Any ideas?

Thanks!
Jessica

Gigabyte-K8NSC-939
AMD Athlon 64 3500
1gig ram
Soundblaster Live 5.1 (taken off)
Win XP SP2
 

Read other answers
RELEVANCY SCORE 46

Hello

Ok so I'm running a MSI 790x Plat and Windows Vista x64 everything is plugged in correctly according the the manual, and I have all of my drivers updated, but it still doesnt recognize the headset or head phones for that matter. This headset works on other computers so i know its not the headset. I've asked around and people have told me i might need to enable it in the BIOS, but I've looked around and i don't know how to find it there. So I guess what im asking is if anyone can help me find the setting within the BIOS where i can enable it, or do i have to do something else.

A:front audio panel issues

make sure nothing is muted in the audio properties applet by right-clicking the speaker icon in the taskbar

Read other 4 answers