Over 1 million tech questions and answers.

BSOD Stop:0x00000050 Page_Fault_In_Nonpaged_Area [moved from Vista/ Windows 7 BSOD]

Q: BSOD Stop:0x00000050 Page_Fault_In_Nonpaged_Area [moved from Vista/ Windows 7 BSOD]


After doing a lot of forum surfing, I have yet to find anything that's worked to get rid of this error. My goal is to get the data off of my drive.. the problem:

I am (not) running XP Pro (not sure what sp.. 3 at one point, but I might have uninstalled it) on a dell poweredge 400sc.

Bios recognizes my hard drive, which is a SATA 400gb (No way to run as a slave with an ATA .. so I've read ..?)

I am getting a BSOD (0x00000050) when booting normally. It flashes for just a quick moment after a few seconds of the XP logo.. then computer restarts.

Computer restarts without showing a BSOD when I try to boot in safe mode.

Computer shows BSOD when plugged into the usb port using a external case. (my other *ATA* hard drive runs windows just fine on this computer) Same thing happens when plugged into a different computer.

Computer shows these errors when I try to use recovery console from my XP CD:

.. I think it's shown the 0x00000050 before.. It's been different almost every time I let the CD load today, but one time it was in OS install mode cause I thought that might help..

I can't seem to get this thing to work. Before this happened my computer was acting really slow; dragging a window around or making selection box on the desktop would make things all skippy and send the cpu to the upper 90s with nothing else running. The BSOD started when I tried to run the SATA as a slave to my ATA.

Am I going to have to send my drive in and pay money for my valuable data? Thank you so much for reading, and for any help you could give me.


Preferred Solution: BSOD Stop:0x00000050 Page_Fault_In_Nonpaged_Area [moved from Vista/ Windows 7 BSOD]

I recommend downloading and running DAP. It can help sort out any driver and firmware related issues on your system

It's worked out well for many of us in the past.

You can download it direct from this link http://downloaddap.org. (This link will open the download page of DAP so you can save a copy to your computer.)

A: BSOD Stop:0x00000050 Page_Fault_In_Nonpaged_Area [moved from Vista/ Windows 7 BSOD]

0x50 = invalid memory referenced
0xd0 = kernel attempted to access invalid memory
0xe3 = thread tried to release a resource it did not own
0xd1 = kernel-mode driver attempted to access invalid memory

Test RAM - Run memtest86+ - http://www.techsupportforum.com/2863029-post5.html

Regards. . .



Read other 1 answers


I was just coding like usual, when suddenly when testing my whole system froze and shut down with a BSOD.
I don't know if this is caused by my wrong code, the recently installed Catalyst 10.12 drivers of defective hardware.

My system is not even an half year old and afaik there were no outrageous temperatures (never have those anyway).

Event viewer stated an ID 41 Kernel Power error.

My system information and an analysis of the memory dump can be found here:

Report of Martijn van Berkel's computer
Executed on 27-12-2010, 21:11:11

ComputerManufacturer: To Be Filled By O.E.M.
Computer Model: To Be Filled By O.E.M.
Computer Name: MARTIJN (in workgroup THUISNW)
System Type: x64 (64-bit) system
MotherboardManufacturer: ASRock
Model: 880GMH/USB3
BIOS Manufacturer: American Megatrends Inc.
BIOS Model: Default System BIOS, version P1.00
Connections: PCI1 (Free), PCI2 (Free), PCIE1 (Free), PCIE2 (In use)
ProcessorModel: AMD Phenom(tm) II X4 955 Processor (Quad Core)
Clock Speed: 3400*MHz
Socket & Cache(s): CPUSocket, 2.048*KB L2 Cache, 6.144*KB L3 Cache
MemorySize: 4.095*MB RAM
Type(s): 2.048*MB RAM (DDR2-667 PC2-5300 333*MHz, DIMM), 2.048*MB RAM (DDR2-667 PC2-5300 333*MHz, DIMM)
HarddiskFile Format(s): NTFS (C, NTFS (D, NTFS (E
Size: 931,51*GB (97,65*GB (C + 20,02*GB (D + 813,84*GB (E )
Free Space: 463,67*GB (50,61*GB (C + 15,83*GB (D + 397,23*GB (E )
DrivesType(s): C: Lokale harde schijf, D: Lokale harde schijf, E: Loka... Read more

A:Windows 7 x64 BSOD (PAGE_FAULT_IN_NONPAGED_AREA - 0x00000050)

Quote: Originally Posted by Flitskikker


I was just coding like usual, when suddenly when testing my whole system froze and shut down with a BSOD.
I don't know if this is caused by my wrong code, the recently installed Catalyst 10.12 drivers of defective hardware.

My system is not even an half year old and afaik there were no outrageous temperatures (never have those anyway).

Event viewer stated an ID 41 Kernel Power error.

My system information and an analysis of the memory dump can be found here:

Report of Martijn van Berkel's computer
Executed on 27-12-2010, 21:11:11

ComputerManufacturer: To Be Filled By O.E.M.
Computer Model: To Be Filled By O.E.M.
Computer Name: MARTIJN (in workgroup THUISNW)
System Type: x64 (64-bit) system
MotherboardManufacturer: ASRock
Model: 880GMH/USB3
BIOS Manufacturer: American Megatrends Inc.
BIOS Model: Default System BIOS, version P1.00
Connections: PCI1 (Free), PCI2 (Free), PCIE1 (Free), PCIE2 (In use)
ProcessorModel: AMD Phenom(tm) II X4 955 Processor (Quad Core)
Clock Speed: 3400*MHz
Socket & Cache(s): CPUSocket, 2.048*KB L2 Cache, 6.144*KB L3 Cache
MemorySize: 4.095*MB RAM
Type(s): 2.048*MB RAM (DDR2-667 PC2-5300 333*MHz, DIMM), 2.048*MB RAM (DDR2-667 PC2-5300 333*MHz, DIMM)
HarddiskFile Format(s): NTFS (C, NTFS (D, NTFS (E
Size: 931,51*GB (97,65*GB (C + 20,02*GB (D + 813,84*GB (E )
Free Space: 463,67*GB (50,61*GB (C + 15,83*GB (D + 397,23*GB (E )
DrivesTy... Read more

Read other 3 answers

Hey Guy's

I've been having problems with one of my computers for a while now we just installed a fresh operating system, added a few drivers and programs but again we get the same error come up :/

I've attached a minidump as well, any help would be much appreciated.

- Ryan

A:BSOD - Page_Fault_In_NonPaged_Area - 0x00000050


Is this a custom build? Please fill out your system specs using this:

System Info - See Your System Specs


Read other 4 answers

Today, when I power up my pc, at boot, after the login screen (2-15 seconds) my pc crashes, and it give me PAGE_FAULT_IN_NONPAGED_AREA.

With bluescreenview I can see that the drivers are different every time, and I read somewhere in internet that it can be a hardware problem.

Two days ago, I've installed a game that require a lot of resources; is it possible that a lot of stress have ruined something?

For now, after 15 reboot, the pc is ok and it's awake from 1 hour.

Did I have to do some tests or by analyzing .dmp it's possibile to find the precise issue?

Many thanks, again


I am confused. Is this on a different system than: http://www.sevenforums.com/crashes-d...sometimes.html ?
Possible out of date drivers:
fffff880`0a94f000 fffff880`0a957000 SSPORT SSPORT.sys Thu Aug 11 17:07:32 2005 (42FBDA34)
fffff880`079c3000 fffff880`079cc000 Afc Afc.sys Tue Jul 11 23:48:20 2006 (44B48D24)
fffff880`07867000 fffff880`0786f000 wacommousefilter wacommousefilter.sys Fri Feb 16 11:12:17 2007 (45D5F401)
fffff880`013e2000 fffff880`013fa000 adfs adfs.SYS Thu Jun 26 14:52:37 2008 (48640195)
fffff880`0719c000 fffff880`071ffd80 nvm62x64 nvm62x64.sys Fri Oct 17 15:01:06 2008 (48F8FD12)
fffff880`0715a000 fffff880`07160000 AsIO AsIO.sys Mon Apr 6 01:21:08 2009 (49D9AD64)
fffff880`10dbb000 fffff880`10dfd000 a8dnpmcr a8dnpmcr.SYS Tue Apr 7 10:07:00 2009 (49DB7A24)
a8dnpmcr.SYS: Could be a virus or malware...

Crashes appear to be caused by avast! Uninstall it, download a fresh installer, and then re-install the fresh installer. When you uninstall, use the avast! uninstall utility.

If the above does not work, remove avast! completely with the uninstall utility and then replace it with Microsoft Security Essentials - Free Antivirus for Windows to test.

Download and install Malwarebytes, update it, do not start the free trial, and then run a full scan. Also run a full scan with your antivirus software installed on your system. If you do not have antivirus software installed, see the Good an... Read more

Read other 3 answers

Hello. I have a Lenovo X201 tablet that has been running great until recently.
I have been getting BSODs. I suspected my memory because it appears to have started shortly after I installed it. I ran Memtest overnight, about 8 hours, and removed the "offending" PNY 4Gb RAM based on the results. I hope the attached images and zip file are helpful to help me resolve my issue. Please contact me if and when you are able. It's likely a driver issue as I've also been having issues with my 6250 AGN drivers and I've unistalled and reinstalled several times.

Attachment 263481

Attachment 263482

Attachment 263483

Attachment 263484


Also from you dump files I noticed:

fffff880`0d446158 fffff880`067c42e0Unable to load image \SystemRoot\system32\DRIVERS\igdkmd64.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for igdkmd64.sys
*** ERROR: Module load completed but symbols could not be loaded for igdkmd64.sys
Driver Reference Table - igdkmd64.sys

please update this driver from here: http://downloadcenter.intel.com/Default.aspx

you may also want to run the system file checker as I noticed some Ntfs errors in the dump files:

Go to Start and type in "cmd.exe" (without the quotes)
At the top of the search box, right click on the cmd.exe and select "Run as adminstrator"
In the black window that opens, type "SFC.EXE /SCANNOW" (without the quotes) and press Enter.
Let the program run and post back what it says when it's done.

Read other 6 answers


I'm continuously getting various types of BSODs, mainly the PAGE_FAULT_IN_NONPAGED_AREA 0x00000050, IRQL_NOT_LESS_OR_EQUAL 0x0000000a and SYSTEM_SERVICE_EXCEPTION 0x0000003b. But sometimes the computer works ok for hours without triggering any BSOD .

Browsing through the different threads in this forum, I've noticed that some users have gone through similar problems as mine, but honestly I have tried a lot of things by myself without success and thus I hope that someone here may be able to help and point me in the right direction.

System information:
Thosiba Qosmio X505
Windows 7 Home Premium 64bit
Intel(R) Core(TM) i7 CPU Q [email protected]
DDR3 Dual Channel 8GB Ram (Two Kingston sticks)
NVIDIA GeForce GTS 360M graphics card (Driver from 12 Sep 2013)
My drivers, windows updates and BIOS are up to date, I have gone thorough a complete computer reboot (factory settings) reinstalling everything, but something is triggering these random BSODs and I can't tell what is it. Could it be the graphics card, antivirus... absolutely no clue at this point .

One typical symptom is that either I get a BOSD, or the screen freezes and sometimes turns off.

Per the posting instructions, the SF file has been uploaded.

Thanks in advance for any help.
Kind regards.

A:BSOD PAGE_FAULT_IN_NONPAGED_AREA 0x00000050 and others

By the way, I'm a new user in this forum.

Thanks again.

Read other 9 answers

I'm using Windows 7 (x.86) and keeping getting BS's frequently.

I think there are several reasons for it and there's more than 1 cause to it.

I attach the most recent mini dump I got, hopefully to find more about the cause of it.

According to BlueScreenView.exe, the cause is win32k.sys+bb7f6.

Any suggestions?



Read other 16 answers

Hello everyone,

Lately I have been getting a BSOD while playing GTA V in the story mode with the settings reasonably toned down to accommodate triple monitors. This is the only time I get a BSOD, it's the first time this computer has ever had a BSOD and it's happened 4 times now. Each time it's for PAGE_FAULT_IN_NONPAGED_AREA which does not seem to make sense to me.

I have tried looking through BlueScreenView to see what driver is causing it and it's always a different driver, but they are all up to date. I used Driver Identifier to check my drivers and they are all up to date as far as I can tell.

PC specs:
Intel i7-5930k overclocked to 4.0 Ghz
16 GBs G.Skill DDR4-2666 RAM
MSI X99S MPower mobo
Samsung 840 Pro 256GB SSD

Let me know if you need anything else. I have not run Memtest yet, but it seems odd that this only occurs in GTA V especially since I use this computer for video editing and have put it through a lot more pressure than this.


What driver do you have installed now ?

Read other 3 answers

Hello Everyone.

I keep getting this error. This usually happens when the computer is idling for an extended period of time. These are some things I've done to trouble shoot the issue.

1. I've ran sfc and it found errors. It was not able to fix the errors. Ive also tried the dism restore health command and it did not work. So I did an inplace upgrade and repaired windows 10.

After this there were no more issues found with sfc /scannow. Computer was stable for a couple days until tonight, when I noticed my computer had restarted.

2. 99% of the time this happens when my computer is idling.

3. I ran driver verifier and it crashed immediately after rebooting. and ive included the results in the logs

4. checked the logs manually with bluescreen viewer, and I see that ntoskrnl.exe is the main culprit

Here are the logs.

Read other answers

Hello guys,
I have been getting blue screen on my PC for the past 5 days at random times.
Error: Page Fault In Non Paged Area: Technical Information: 0X00000050
My PC is running Windows 7 Ultimate 64 bit.
Here's what I have already tried:
Tried setting the paging file size to none and then back to automatic.
Removed the RAM, changed the slot.
Ran MemTest86, came out with zero errors after all 4 passes.
Ran disk check, cleaned registry.
Finally, Did a fresh install of the OS.
And yet, I have the problem. The frequency of the error popping up has become low after the fresh install, but it still does. And I have no anti virus at this stage.
Not sure how to go about it next. Any help would be appreciated.
I've attached the dump file.
Thanks in advance!

A:Experiencing BSoD Randomly - 0x00000050 Page_Fault_In_Nonpaged_Area

Run MemTest86+ for a minimum of 8 passes.

Read other 1 answers

First sorry for my english.

OS: OEM Windows 7 Professional 64-bit, SP1 (5 months old)
Hardware: 6 months old
Processor: Intel I7 2600K
MB: Asus P8Z68-V PRO
Graphic Card: Asus GTX 570
SSD: Kingston HyperX 120GB
Memory: 8GB Corsair 1600

My problems with BSOD are pretty random (playing games, watching videos), but they are always 0x00000050 PAGE_FAULT_IN_NONPAGED_AREA.

One of the sure way to gat this BSOD is to run miranda instant messenger (Yaho?s Miranda Pack) and almost any video file (Last time it was .mkv).

I checked my memory with Memtest86 (8 runs) and find no errors. I updated BIOS on motherboard and firmware on SSD. My current video drivers are 290.53-desktop-win7-winvista-64bit-international-beta, but I had BSOD problems even with non beta drivers.

Any help would be appreciated.

A:BSOD 0x00000050 PAGE_FAULT_IN_NONPAGED_AREA Random Occasions

Hi -
The 10 dumps go back to October 2011 and all have bugcheck = 0x50 = invalid memory referenced.

Remove Daemon Tools/ Alcohol 120 for now -

sptd.sys Sun Feb 27 14:29:52 2011 (4D6AA630)

Run Driver Verifier - Driver Verifier - sysnative.com - MVP

Regards. . .



Loading Dump File [C:\Users\PalmDesert\_jcgriff2_\dbug\__Kernel__\012112-6037-01.dmp]
Built by: 7601.17640.amd64fre.win7sp1_gdr.110622-1506
Debug session time: Fri Jan 20 18:16:59.594 2012 (GMT-5)
System Uptime: 0 days 0:32:29.453
Probably caused by : ntkrnlmp.exe ( nt! ?? ::FNODOBFM::`string'+4611f )
PROCESS_NAME: miranda32.exe
FAILURE_BUCKET_ID: X64_0x50_nt!_??_::FNODOBFM::_string_+4611f
Bugcheck code 00000050
Arguments fffff8a0`0dc48000 00000000`00000000 fffff800`0307b74e 00000000`00000000
BiosVersion = 1101
BiosReleaseDate = 11/23/2011
SystemManufacturer = System manufacturer
SystemProductName = System Product Name
MaxSpeed: 3400
CurrentSpeed: 3411
Loading Dump File [C:\Users\PalmDesert\_jcgriff2_\dbug\__Kernel__\011712-5772-01.dmp]
Built by: 7601.17640.amd64fre.win7sp1_gdr.110622-1506
Debug session time: Tue Jan 17 14:38:02.326 2012 (GMT-5)
System Uptime: 0 days 0:25:39.185
Probably caused by : ntkrnlmp.exe ( nt! ?? ::FNODOBFM::`string'+4611f... Read more

Read other 3 answers

Hi, this is my first post on this forum, I actually come to you from another forum that was unable to help me resolve my problem.

For the last month or so I've been getting intermittent BSODs, all of which reference 'ntoskrnl.exe' as the culprit in BlueScreenView, however despite copious research I am unable to resolve the issue.
So far I have tried:

-Run Memtest for 7 passes, clean
-Run chkdsk /f multiple times, all clean
-Run Seatools for DOS long test, clean
-Updated video card drivers to 13.1 (latest)
-Verified that no system components are overheating or undervolted
-I run virus scans, registry defrags/cleaning regularly, all clean
-sfc /scannow, all clean
-I have no active anti-virus that could cause the problem
-Stress tested both the GPU and CPU, all stable
-removed Acronis Trueimage drivers I thought may have been causing the issue, no effect
-replaced my 60Gb C: drive with a new 300Gb, as I was running low on space and thought maybe that might have contributed, no effect

Things I have not yet tried:
-Scan entire system for outdated drivers (I can't find a reputable program that will do this, all of the ones I've tried just want me to pay)
-I ran sfc/verifyonly which reported integrity violations, however I don't know how to read the dump file and identify the issue.
-Full format and reinstall Windows, obviously this is a last resort

As per the instructions here: Blue Screen of Death (BSOD) Posting Instructions

I have run the tool and att... Read more

A:BSOD ntoskrnl.exe+f11e4 PAGE_FAULT_IN_NONPAGED_AREA 0x00000050

Please post the following report before we proceed:Windows Genuine and Activation Issue Posting Instructions

Read other 6 answers

Dear sevenforums members,

At last I have to accept that I am not able to find and/or solve this issue myself. I keep getting frequent (multiple time per day) BSOD's, but to my knowledge at random occasions. I will add all asked information, dump files etc. And I will also give an overview of what I have tried myself. If one could help me out, that would be very much appreciated as I have reached my own limits of problem solving. My computer used to do a restart after each BSOD, the last weeks even the Blue Screen freezes, which may corrupt the dumpfiles (?).

Fujitsu Siemens Amilo Li 3745 Desktop
Windows 7 x86 Home Premium (update from vista)
NVIDIA? nForce? 630i (MCP73-PV)
Intel? Core?2 Quad Q8300
Nvidia GT120
2x WD Harddiscs (1TB + 500GB)
Approx 4 year old.

Work done so far:
I used the windows build in checks for both RAM and HD's, I ran memtest86 for 12 hours (no faults), I have ran the system on either RAM chip alone, I installed windows on a new HD and disconnected the old one. I have tried to update most drivers. Read many threads about BSOD's but did not yet find the ultimate solution.

A:BSOD frequent but at random (PAGE_FAULT_IN_NONPAGED_AREA 0x00000050)

All of them pertain to NTFS issues. Has this been occurring even with a fresh new copy of Windows? If so, you may wanna do the following:

Update your BIOS. If your BIOS is up to date, reflash it ("reinstall" it). BIOS sometimes can get bugged.
Update all your motherboard drivers from the OEM vendor's website, especially those relating to your drive controller (may come a driver suite for your mobo).
If those two do not resolve the issue, most certainly we're dealing with a failed motherboard, which are nearly impossible to test without a motherboard testing kit. Unfortunately, because the system is so old, most likely your warranty for it has expired. You may be able to find an exact replacement board, or you may need to just purchase a new board.
For other miscellaneous checks, you should look into:

Uninstalling/updating Nforce System Management Controller Driver (I believe it's part of the Nforce chipset driver suite). It's dated 2007 right now, so something should be done with it.
You have some miscellaneous OEM PC Camera driver (snpstd.sys) that's really old (2006). Uninstall it or update it.

Read other 1 answers

been having this problem for along time now. .dmp's attached.

Windows 7 64 bit
motherboard TF520 A2+
Processor Amd athlon 64 x2 dual core 3.2 ghz
memory: 4096MB Ram
graphics card: geforce gtx 550TI

Bug Check Code: 0x00000050
Perameter 1: fffff880`09cc7118
2: 00000000`00000000
3: fffff880`10b840b9
4: 00000000`00000000
Cause by driver: ntoskrnl.exe
Caused by address: ntoskrnl.exe+705c0

A:BSOD while playing any game ‎0x00000050 PAGE_FAULT_IN_NONPAGED_AREA

* Avast can be a contributing cause of BSOD'S .
Please remove and replace with Microsoft Security Essentials AT LEAST TO TEST.


Microsoft Security Essentials - Free Antivirus for Windows
* We suggest you run the System Update Readiness Tool (SURT) and then update to SP-1

32 Bit

Download: System Update Readiness Tool for Windows 7 (KB947821) [February 2012] - Microsoft Download Center - Download Details

64 Bit

Download: System Update Readiness Tool for Windows 7 for x64-based Systems (KB947821) [February 2012] - Microsoft Download Center - Download Details
Now update to SP-1

Learn how to install Windows 7 Service Pack 1 (SP1)

Read other 4 answers

Im getting the BSOD randomly using windows 7 ultimate home edition 64Bit
some times it does it while on idle and some times it does a few minutes after reboot please see attached files any help is greatly appreciated

A:BSOD Randomly Error code 0X00000050 PAGE_FAULT_IN_NONPAGED_AREA

Welcome aboard.

First make it sure that there is no virus. Scan the system for possible virus infection.
Anti-rootkit utility TDSSKiller
Windows Defender Offline
Let us know the results.

Read other 6 answers

Hi last week I installed a new video (which may be the problem but I don't think so), and since then I have had 2 bsod. Not sure if I should be worried about this yet, but I am gonna try my luck on this forum.

The most recent bod was a PAGE_FAULT_IN_NONPAGED_AREA 0x00000050

The one a couple of days earlier was a SYSTEM_SERVICE_EXCEPTION 0x0000003b

i have attached the latest DM Log file

My machine is an AMD FX-6200 & Gigabyte GA-970-D3
The graphics card is a Gigabyte GTX 660

Hope I have included the correct information.


A:BSOD Playing Guild Wars 2 - PAGE_FAULT_IN_NONPAGED_AREA 0x00000050


Before changing drivers, make it sure that you have earlier System restore points made in your computer. You can check it easily by using CCleaner looking at Tools > System Restore.

If there is no points, make a System Restore Point Manually.

Can you roll back the driver using Device Manager.
Go to Start
Type Device Manager
Then expand your Display Adapaters
Click on your graphics card
then under the drivers tab click Roll Back Driver

I suggest running a stress test on your GPU.
Stress test your graphics card with Furmark

I recommend running it for around 30 minutes


Furmark will increase the temperature of your GPU rapidly so keep and eye on your temperatures

Read other 7 answers


My friend gave me an old laptop. It runs Windows 7 Starter. When I boot up the system, the Windows Error Recover showed up asking me to either "Launch Startup Repair (Recommended)" or to "Start Windows Normally". When I tried starting Windows normally, it will show the loading screen but after sometime in the middle of the loading, a BSOD will show up. I observed the BSOD and so far I got two 'almost the same' BSODs. The first one is: [***STOP: 0x00000050 (0x80787000, 0x00000000, 0x8248D853, 0x00000000)]. The second is: [***STOP: 0x00000050 (0x80787000, 0x00000000, 0x8244A853, 0x00000000)]. I tried starting Windows Startup Repair. It performs a System Restore. It didn't fix the problem.

Since this laptop is not my original ownership (originally from my friend but got tired of this BSOD and eventually gave it to me), here are the known specifications of the laptop:
Processor: Intel Atom
OS: Windows 7 Starter
Samsung Model: NP-N150

I should post a something like DMP file or crash log. I really want to but unfortunately I can't. I cannot boot the normal windows dekstop. I can't even boot in safe mode (it doesn't show up in screen).

I hope you can help me. Thanks in advance!

~ Bryan ~

Read other answers

I've got some problems with BSOD.

It's happening while using different programs, like Microsoft Word, Photomatix pro and Photoshop CS5. Also it happens while it has an BSOD and its starting up again (in the middle of starting up or when I first see the desktop).

I have totaly no idea what to do. Can someone help my? I have insert a zip file and 2 photos of a BSOD.

Thank you!

Attachment 351361

Attachment 351363

Attachment 351364

A:BSOD starting Windows and other, stop 0x00000135 and 0x00000050

Caused by AVG antivirus.


Microsoft (R) Windows Debugger Version 6.3.9600.16384 AMD64
Copyright (c) Microsoft Corporation. All rights reserved.

Loading Dump File [C:\Users\YUSRA\Downloads\ACER-V3-771-di_03-03-2015_170048,66\030315-41901-01.dmp]
Mini Kernel Dump File: Only registers and stack trace are available

************* Symbol Path validation summary **************
Response Time (ms) Location
Deferred SRV*c:\symbols*http://msdl.microsoft.com/download/symbols
Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
Windows 7 Kernel Version 7601 (Service Pack 1) MP (4 procs) Free x64
Product: WinNt, suite: TerminalServer SingleUserTS Personal
Built by: 7601.18717.amd64fre.win7sp1_gdr.150113-1808
Machine Name:
Kernel base = 0xfffff800`0305a000 PsLoadedModuleList = 0xfffff800`0329e890
Debug session time: Tue Mar 3 18:02:12.787 2015 (UTC + 6:00)
System Uptime: 0 days 0:23:46.051
Loading Kernel Symbols

Press ctrl-c (cdb, kd, ntsd) or ctrl-break (windbg) to abort symbol loads that take too long.
Run !sym noisy before .reload to track down problems loading symbols.

Loading User Symbols
Loading unloaded module list
*******************************... Read more

Read other 1 answers

Hi I have ocasional BSOD on my Windows 7 32 bit laptop (HP Elitebook 6930p). I have seen that others users with similar problem had their issue resolved and I was hoping that somebody can help with mine. I founded that problem relates to the wmiacpi.sys but I have no idea how to fix this and where to start it. Would appreciate your help in this. If the same issue was already fixed on this forum could you point me out to the right direction?
Many thanks

A:BSOD Windows 7 32bit, 0x00000050 stop error

Hi wariat and welcome to TSF. Please post this request in our BSOD Forum here. BSOD, App Crashes And Hangs - Tech Support Forum. We have experts there that'll help you out. They are busy so please be patient and you'll be helped ASAP.

Read other 14 answers

I too am getting this message on my cousins computer but can't get anywhere but the blue screen on start up then it says that c:\\windows\system32\config\system is not found and then reboots to same thing, i have tried to recover and reinstall with no luck. I can't get past the error codes :: PAGE_FAULT_IN_NONPAGED_AREA, STOP: 0x00000050

any ideas how to windows at least boot in safe mode? the F8 options won't work either and can't do a reinstall cuz that won't work and recovery won't work.

any help would be greatly appreciated.

A:Page_Fault_In_NonPaged_Area, stop: 0x00000050

Check or replace the systems memory... We will continue from there

Read other 8 answers

I have been getting the following error and this seems to be after installing the HP software for a officejet 7400 series. I started getting these msi installer errors. Well I removed the hp software and the msi loader errors stopped then I started receiving the followinf error :

stop 0x00000050 (0xE1CE7000, 0x00000000, 0x891A052A, 0x00000001)

I feel it has something to do with the darn hp software, funny thing is they tell of this issue and have a download for this. When I try to run the download it says it's not supported. So like I said I removed the software which was a nightmare to remove.

So, not sure what to do other then doing a windows repair or complete reload. When I run in safemode everything runs gr8. When I try to run in normal mode I get the BSOD. I have searched for the files that some say can cause this from a malicious kernel mode driver. was unable to find the files that are suggested that can cause this. I have provided serveral dumps if anyone out there could help would many thanks,,, tried going to windows knowledge base and they seem to think it's malicous code causing it. I cannot find the files they suggest would caause thi draw32 & Mtupd I think that was the spelling. I also ran memory test which the memory checked out ok. So,,, other then reloading windows not sure. Like I said everything was gr8 until loading the HP software. Now after removing the software I'm left with these BSOD now.

I did find the following erro... Read more

A:Stop 0x00000050 or Page_fault_in_nonpaged_area

Hello and welcome to Techspot.

Zip 5 or 6 of your latest minidumps together and attach them here.

You can find your minidumps in the following directory. C:\windows\minidump.

Please note. Techspot has a limit of 100kB for attachments, so you may need to attach several zip files.

Regards Howard :wave: :wave:

Read other 8 answers

Hello everybody!

New guy in the topic/forum but the same problem:
STOP: 0x00000050 (0x80363DC1, 0x00000000, 0x80363DC1, 0x00000000)

Started to get this blue screen in the last day, and don't know the reasons, but I had other symptoms, like:
1. each time I want to start my computer he makes 2 times restart before getting the wellcome screen
2. makes restarts without saying smthing, but afterwards I get a message: "the system has recovered from serious error"

My latest 2 minidumps are here: http://www.techspot.com/vb/topic45928.html. I don't have more cause I made a system reinstall an hour ago.


A:Page_fault_in_nonpaged_area Stop 0x00000050 (0x80363DC1, 0x00000000,

Do you have a Creative sound card?

Read other 8 answers

I've had a reoccurring issue with my work laptop that has stumped our IT department and caused me to have my laptop re-imaged 3 times (new HDD each time) and my shell swapped once. I'm getting sick of going back and need to figure out what is causing this. After a fresh image everything is fine for a few weeks. Then all of a sudden the computer will start losing it's network connection after 30-60min of use. I'll be in the middle of something and realize that I no longer am able to access the internet (this is through IE and Firefox as well as over outlook and other programs using the network connection). This happens whether I'm wired or wireless. If I try to open task manager or a new program I'll get an "insufficent memory" error (don't have specifics, will post a screenshot next time it happens). The computer will run very slow until I restart. Then everything is just fine for another 30-60min til this happens again. Ocassionally I will also get a BSOD for a Page Fault error with the following info:
STOP: 0x00000050 (0xBAD0B114, 0x00000000, 0x805BA8AR, 0x00000002). I've checked the event viewer and I see errors related to my firm's encryption service not being able to encrypt something due to a lack of system memory as well as errors around M$ communicator not being able to connect. I've attached the minidump from the last time this happened. This happened on the old and new shell and I've ran a RAM check and haven't seen any issues. Additionally I've received ... Read more

A:BSOD STOP: 0x00000050 etc..

Welcome to TSF,

What a pleasure to see so much information when posting to us. Thanks for it all, but I have little to offer but two links that may help you research your problem further. A couple of questions first however,Are you Windows Updates current
Are you only running one Anti-Malware Program
How old is this Laptop? If it were a PC I would immediately suspect dust bunnies clogging the inside of your tower. Has your IT technician opened the back to take a look for anything out of order there
Referring to your Stop error 0x00000050 take a look at this Microsoft link for assistance.

How to troubleshoot Windows Stop errors may be of assistance too.

Keep us posted,

kind regards,

Read other 6 answers

Hey guys I'm getting this bsod when I start my computer up. Like it goes through all the windows loading processes and right after I click on my user icon to login it gives me this message. This first started towards the end of august but I never bothered to fix it then because I was leaving for school in a couple days. trying to log in to safe mode doesn't work, however it does work when I load up in directory services restore mode (windows domain controllers only). No other mode seems to work. When I load up safe mode it doesn't give me a bsod but it gives me an error but it automatically restarts so I don't know what the error message says. I've tried a system restore to pretty much all my restore points but for some reason system restore wont work. I've read around and I had originally thought that both my sticks of RAM (2gigs each) were bad. I had tried booting with each one of them in different slots, basically every combination and there's no difference. However, I was able to use different sticks of ram from my parents computer (which is 5 or 6 months old) and I was able to get my computer to work when I used a 1gig stick of ram. When I used any configuration of ram that gave me 2 or more gigs of ram it gives me the bsod which is strange. Any help would be much appreciated.

Technical information:

STOP: 0x00000050 (0x8BA9A7E8, 0X00000008, 0x8BA9A7E8, 0x00000000)

A:STOP: 0x00000050 BSOD

These are classic signs of a Rootkit infection and although I deal with them daily, I 'm not allowed to advise you on this.

Click to Report your own post and ask a Moderator to move the thread to the Security section where, with luck after a few days, a specialist adviser will tell you what to do next.


Read other 2 answers

In my blue screen there is "vbabosec.sys" plus PAGE_FAULT_IN_NONPAGED_AREA
Any help is very appreciated, thanks in advance.

System Health Report and Dump Files are attached with the thread

A:BSOD error 0x00000050 PAGE_FAULT_IN_NONPAGED_AREA "vbabosec.sys"

Most of your files do indeed show Vbabosec.sys There is no mention of this in Google, except for your post. This is usually and indication that the BSOD was caused by a name changing Trojan. I will ask our security people to look into the possibility that you were indeed infected. In the mean time run a full updated anti virus scan. Download and run a full scan with Malwarebytes.

Read other 9 answers

Hello all,

I am working on this error and have run out of ideas. During start up I am getting a BSOD.


STOP: 0x00000050 (0xFFFFF8804913E600, 0x0000000000000001, 0xFFFFFA800324C2E6, 0x0000000000000005)

* I have included the zip files that include the dump info, but when trying to run perfmon /report I receive an error that states:

Error: An error occured while attempting to generate the report. The system cannot find the patch specified.

System Info:
OEM Windows 7 Home Premium x64
Acer Aspire 5532
AMD Athlon 64 Processor TF-20 (1.6ghz)
ATI Radeon HD3200
3GB Memory

What I Have Tried:
-chkdsk -> 0 problems
-System Restore -> system restore ran, but deleted restore point on restart due to missing windowsinstaller
-Startup Repair -> detected no problems
-memory/hardware check -> found 0 errors
-sfc /scannow -> found corrupted files and repaired
(after this completed, i was able to start up windows in normal mode longer than i had previously been
able to, but when accessing the control panel it crashed again)
-sfc /scannow a second time -> 0 corrupted files

This is not my computer and i do not know exactly when the problem began. The only recent software change i can see are the installation of Microsoft Silverlight, Compatibility pack for the 2007 Office system, and Microsoft office powerpoint viewer 2007.

Any help on this would be greatly appreciated!!!

- Ian

Problem signature:
Problem Event... Read more

A:BSOD during startup, STOP: 0x00000050

All crashes were related to McAfee. I would suggest uninstalling the software and then re-installing it: How to uninstall or reinstall supported McAfee products using the McAfee Consumer Products Removal tool (MCPR.exe)
If the above does not work, remove McAfee for good: How to uninstall or reinstall supported McAfee products using the McAfee Consumer Products Removal tool (MCPR.exe)

Replace with either of these:Microsoft Security Essentials - Free Antivirus for Windows coupled with Malwarebytes. Do not start the free trial of Malwarebytes. Just use the standalone version, update it, and scan your computer once a week with Malwarebytes and with Microsoft Security Essentials.

Good and Free system security combination.

Read other 3 answers

Since a few days ago when I start up my laptop, I recieve a BSOD at the windows loading screen. It happened a few times in the past, and system repair dealt with it easily. But now, all my system restore points are gone, system repair doesn't help and I don't know what to do. The only thing I can do is F8 and F12 at boot. When I try to go into safe mode, the laptop whirrs really loudly, and restarts.

It's not my picture, but it's the same error.
STOP: 0x00000050 (0xFFFFF880009AA000,0X0000000000000000,0XFFFFF800032766FA,0X0000000000000000)

Thanks in advance

A:BSOD at boot, stop 0x00000050

A stop 0x50 is a memory error. That means either the physical RAM is causing issues or any driver is passing bad info to the RAM.

Do two things. First and foremost, make it sure that your RAM is healthy. Test your RAM modules for possible errors. How to Test and Diagnose RAM Issues with Memtest86+
Run memtest86+ for at least 8 consecutive passes.

If it start showing errors/red lines, stop testing. A single error is enough to determine that something is going bad there. Report us at this point, no need to go for the next part of this post.

If RAM is free from errors, Try to boot in Safe Mode. If the computer boots in Safe Mode, execute the Blue Screen of Death (BSOD) Posting Instructions and attach the data with your reply post.

If Safe mode does not work, too, let us know. We will try to explore other ways to troubleshoot the issue.

Read other 9 answers

Hello! My PC turned 4x already since yesterday a blue screen saying page fault in nonpaged area. I'm clueless and not so pro in checking dump files, but i a average user in knowledge about computers.

My PC Specs are:
Processor:Intel Core i5-4440 3.1 GHz
Motherboard:Intel DB85FL Motherboard
Ram:Kingston 4-GB DDr3-1333 (2x)
Graphics Card:AMD HD 5670 2GB (Powercolor)
HDD:Seagate 500 GB
Casing:Thermaltake Commander MS-I

I have a quite good cable management in my pc so the airflow is good and have 2 fans exhaust and intake fans to maintain the coolness of the inside.
Maximum Temp of the Processor basing on (HW monitor) : 60-63 C full load.
IDLE: 32-35 C
Didn't Overclocked the Graphics card or processor.

Sorry forgot to post/attach the file
LINK:Attachment 312673
Good Day!

A:BSOD Page_Fault_In_Non_Paged_area Stop 0x00000050 ( cdd.dll )

Hello darkbing, and welcome to Seven Forums.

Please read the instructions here: Blue Screen of Death (BSOD) Posting Instructions, and post back with the needed information. One of our BSOD experts should be by later when able to further help.

Read other 4 answers

hi sevenforums,

ive been having this bsod when im playing in full screen mode. i tried several troubleshoot 1. expanding atikmdag.sy_ 2. uninstalling amd drivers and installing a new one. 3. clean install ( i just reformatted my pc) but still i get this problem after 10-30min onf playing full screen. i dont know what else to do so please help me. i uploaded the file from dm collector.

mobo: crosshair 3 formula
proc: amd x4 965
vcard: sapphire HD 7770
Ram: 8gb
thank you and any help will be much appreciated.

Read other answers

Hello everyone! Here I am again with a problem that needs solving.. fortunately, I always come here and everyone is kind and helpful. I have to go out for a couple hours so I have to submit this kinda fast. Anyway, I've been working on it all day and can't get it going.
What happened is my computer went out with a housewide power outage. Happens allll the time and never had a problem. 
But now I am getting the BSOD when it starts to try and load Windows.
I have NOT added any new hardware or software recently
I have no System Restore points
I have no System Image points
The System Check and Memory check said it could not detect the problem
I can not Boot in any safe mode
I do not have my Windows 7 CD or KEY
I've found others around the internet with the same problem and all the answers say something like "Hey! Download this so and so and run it "But I CAN'T because I can't get into windows! I need something that will boot on a disc and run a registry fix or something.
Anyway, I have to run! I'll add anymore info u need when I get back. There is the key information in the Topic of this post. And keep in mind that I run windows 64 bit.
THANKS in advance everyone!!


The error message seems to indicate there is a hardware or possibly a driver issue. http://msdn.microsoft.com/en-us/library/windows/hardware/ff559023%28v=vs.85%29.aspx Trying starting from the Last Known Good Configuration. When the computer boots, hold down the F8 key, then select Last Known Good Configuration from the advanced boot options menu.
It's possible a power surge may have damaged the computer. Unplug it, open up the case and look at the capacitors on the motherboard. If the ends of any of them looked puffed out, or look like they are leaking, your motherboard was damaged.
EDIT: Another user, bwhisnant, found this article. This seems to be a known issue caused by Windows Update. The apparent solution is in the article. http://www.infoworld.com/t/microsoft-windows/users-find-fix-botched-kb-2982791-and-kb-2970228-windows-update-248476

Read other 2 answers

My computer has been running perfectly, and flawlessly the past couple of days, and i have been really happy. Today, however, I booted it up and was going to play come Minecraft. It goes through the login screen, but as soon as the game loads and i begin to walk around BLUESCREEN. This isn't the first time it happens, and its not with all games. I played Audiosurf yesterday, a game from steam, and it worked perfectly with no problems. I think its java acting up, but since i have no idea how to 'read' bluescreens, i came here for help. Any ideas?

A:BSOD once again [moved from Vista/ Windows 7 BSOD]

Are you running XP?

Read other 5 answers

2 days ago, I left Blizzard Background Downloader on all night and used Auto Shutdown to turn off the computer at about 6am. I've done this 100's of times before with other downloads, but never the Blizz downloader. I have also recently changed the nVidia settings on my GTX 260 gpu to "high performance" parameters, ie making it more nVidia controlled than application controlled (world of warcraft). It greatly improved my performance, but I don't know if either of these are related to my BSOD problems. I can run in safe mode just fine, have been for hours, but upon a regular restart I might get 1-2 minutes of normal use before BSOD. Here are a few dumps, I hope someone can look them over. I have tomorrow off and I don't want to spend it reinstalling Win7 ...
8/22/2012 2:17:43 PM
fffff8a0`a756e560 00000000`00000000 fffff800`03ca2c84 00000000`00000005
ntoskrnl.exe ntoskrnl.exe+7f1c0 NT Kernel & System Microsoft? Windows? Operating System Microsoft Corporation 6.1.7601.17835 (win7sp1_gdr.120503-2030) x64 ntoskrnl.exe+7f1c0

dmp files:
I've attached the 7forum BSOD diag tool folder, but I ran it in safe mode and something tells me that won't help much. I can try to read from normal boot but I only get about 30 sec before BSOD. I've passed windows memor... Read more


The problem is due to one of the system log files becoming corrupt.
Best way to fix is to try a system restore from 2 days before the problem
If that does not work a repair install will most likely solve the problem
Repair Install

Read other 9 answers

I have a 18 month old Dell Optiplex 320. Last week it started blue screening with the message stop: 0x00000050. I ran the hardware diagnostics from the utility partition and found that the ram was bad. Under warranty, Dell sent me some new memory. The RAM and every other system passes all of the hardware diagnostic tests now.

Starting the machine results in the BSOD stop: 0x00000050. Safe mode, same thing. Tried restoring to an earlier restore point to no avail. I grabbed the OEM XPsp2 disk and tried to use the recovery console. I was presented with the list of Windows installations (c:/windows), I pressed 1 to select the directory and got an instant BSOD. I pulled the drive and mounted it on another system, made an image of the disk (just in case), and ran chkdsk. No problems found there. I also ran Malwarebytes- nothing found. I put the drive back in the machine and booted from the XP CD again, this time electing to try to repair the Windows installation by starting the installation process. Just a few seconds into the "Checking for previous installations" message, BSOD stop: 0x00000050.

I'm pretty much at a loss at this point. Any advice would be appreciated. I've attached what I believe to be the dump files from the last four blue screens.

Just noticed that Windows update was running at the time the BSOD's started. I'm attaching that log as well.

A:BSOD stop: 0x00000050 from Recovery Console


look through here-


Read other 2 answers

Hello, I have been posting here for the past 2 weeks and have not found a 100% clear answer for my problem. First off, my computer ran fine for about 5 hours after a 10-day vacation and just an hour ago I got a BSOD Error 0x00000050. I have ran Memtest and it shows a lot of red layers/lines, but it took about an hour to get 1 pass and I got a whole list of red lines with numbers. I'd be glad to do the memtest in which I take test 1 RAM stick at a time tomorrow. When I startup after the BSOD, I get an error from my AMD Catalyst Manager saying my display drivers need to be reinstalled. My device manager shows that my AMD Radeon 7800 HD Series and Intel HD Graphics 3000 have a yellow triangle and an exclamation mark. My build is exactly a month old today and it really sucks to have this happen to me because I spent all my summer job money on this build. If reformatting or purchasing a new part fixes this and it is 100% that it will fix this I would be willing to do it. Right now I am in Safe Mode with Networking and I have provided you guys with my Seven Forums Files. Thank you for all the awesome support from this forum!

A:BSOD While doing anything for 10+ minutes STOP Error 0x00000050

I have ran Memtest and it shows a lot of red layers/lines

That indicates a defect in your RAM stick(s). You should test each one at a time to identify the problematic one.

Your AVG software is also involved, I would recommend removing it.

BugCheck 19, {3, fffffa800789c5e0, fffffa800789c5e0, fffff8800789c5e0}

Unable to load image \SystemRoot\system32\DRIVERS\avgidsfiltera.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for avgidsfiltera.sys
*** ERROR: Module load completed but symbols could not be loaded for avgidsfiltera.sys
Probably caused by : Pool_Corruption ( nt!ExDeferredFreePool+a53 )

Read other 3 answers

Hi guys, so I was playing Dota 2 for sometime, then I closed the program and walked away from my computer. When I came back I saw a BSOD. Please help me find the reason behind the BSOD. I have attached a picture of the BSOD I took and the zip file from the DM log collector Thank you very much!

A:BSOD after playing Dota2, Stop: 0x00000050

Hi bfmv,

Please visit the ASUS support page for driver updates for the wifi network driver
Per the photo and a look at the dumps it is causing the crashes

0: kd> lmvm athrx
Browse full module list
start end module name
fffff880`05051000 fffff880`05306000 athrx T (no symbols)
Loaded symbol image file: athrx.sys
Image path: athrx.sys
Image name: athrx.sys
Browse all global symbols functions data
Timestamp: Wed Mar 21 14:42:59 2012 (4F69DAE3)
CheckSum: 002B829C
ImageSize: 002B5000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4

Read other 1 answers

I'm very sorry for posting a lot, but I've been getting so many problems and BSOD with my computer lately. I believe it's a memory problem, but I'm not sure. I'll be going on a vacation for the next 10 days, so I won't have access to internet and my computer. I've been waiting all day for a solid answer on the problem. Everything is telling me it's my RAM, but I want to make sure 100% it is before I do anything else. I've also been also getting BSOD errors like 0x0000001a and 0x0000001e both I believe are hardware/software problems. I am still looking for a 100% answer, I'll be able to do tests/scans tomorrow for a few hours then I'm off. If doing a "factory restore" solves this I would be extremely happy to do it. I had to use Winrar because I didn't have 7-Zip. Thank you SevenForums!

A:BSOD While doing anything for 10 minutes STOP Error 0x00000050

Hello Massaddict and welcome to Sevenforums.

BSOD Analyse

3rd party driver concerns

VirtuWDDM.sys Mon Aug 8 11:42:14 2011 (4E3FAF76)

VirtuWDDM VirtuWDDM Kernel 8/8/2011 2:42:14 AM

2: kd> lmvm VirtuWDDM
start end module name
fffff880`04071000 fffff880`04086000 VirtuWDDM (deferred)
Image path: \SystemRoot\system32\DRIVERS\VirtuWDDM.sys
Image name: VirtuWDDM.sys
Timestamp: Mon Aug 08 11:42:14 2011 (4E3FAF76)
CheckSum: 00010AF4
ImageSize: 00015000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4
VirtuWDDM.sys, as far as I'm concerned, is a somewhat known BSOD causer in Windows 7. I'd suggest uninstalling it. If it appears in \SystemRoot\system32\DRIVERS\VirtuWDDM.sys, let me know and we'll troubleshoot further.

You do have a lot of 3rd party drivers. Be aware of those. Sometimes you might not need additional drivers for Windows 7, it'll choose them for you. If you really need them, make sure that they're digitally signed by Microsoft. The only additional drivers I personally recommend, is the Graphics Driver, and the Audio Driver.


As we covered the 3rd party drivers part, it's even likely that a driver is disturbing your memory. Second possibility is that the sticks themselves, or the motherboard slots are broken. It's very unlikely that the slots are broken though.
Do a scan with Memtest86+. Memtest is a sc... Read more

Read other 7 answers

Hello All,

Just discovered this forum, its already proved quite helpful to me, but I unfortunately don't seem to have isolated my problem completely yet. Whenever I log into my cpu in normal mode, before I take any actions or access any programs, I receive a couple of McAfee Error Messages, then receive the BSOD with the following Stop message and info:

PAGE_FAULT_IN_NONPAGED_AREA ***STOP: 0x00000050 (0xE2BD5000, 0x00000000, 0x804FCB3F, 0x00000001).

I visited a couple of the websites suggested at the top of this topic list, and tried to implement some of the suggested troubleshooting techniques, such as removing/retesting hardware and running chkdsk (no errors found), but still receive the same BSOD shortly after any time I try to log in normally (i.e., not in Safe Mode). Even after reinsalling my Windows XP disc, very little improvement (maybe a bit more working time before the pop-ups and the BSOD).

I tried contacting McAfee and having them troubleshoot, they insisted that my problem was a corrupted version of Windows (they couldn't access IE to remove or update their program). When I contacted Dell, they insisted that the problem likely lay with McAfee and that I needed to go through them to have their program removed or reinstalled.

I can't uninstall McAfee myself via any normal method. I can get on IE, but can't seem to download Windows Updates any longer. So I'm left with this frustrating circular logic of not knowing where... Read more

A:BSOD Stop Error 0x00000050 assistance requested

who's normal these days?

I can't uninstall McAfee myself via any normal methodClick to expand...

Have you seen if the program you are trying to delete is present in the Control Panel?
< left click Start
< highlight Settings and then Control Panel
< click Control Panel
< click Add or Remove Programs (in Classic view or Category view)
< click McAfee after the list loads
< click the button Change/Remove
Hope this helps oh and by the way CPU means Central Processing Unit http://en.wikipedia.org/wiki/Central_processing_unit

Read other 10 answers

Hello Everybody

My commputer has been crashed several times and BSOD has appeared
I checked and I found that my HDD has bad sector
After that, I changed my HDD and RAM

But now, I still has BSOD
detail : Page Fault In Nonpaged Area. Stop: 0x00000050
and I saw the number in BSOD run from 0 to 100

I also attach SF_22-01-2014 to this thread
Please help me. Thanks to all of you

A:BSOD Page Fault In Nonpaged Area. Stop: 0x00000050

No dumps included, please follow Dump Files - Configure Windows to Create on BSOD to enable "small memory dumps"

Read other 2 answers

When I start my computer it goes through between 5-10 freeze's with the BSOD stop call until it gets it right and finaly takes off and works fine. My question is how can a computer change its boot procedure so that it finaly gets it right and launches. It's so confusing because I thought that a computer followed a set of instructions and wouldn't vary the procedure but the results show that something changes and it finaly takes off. Sometimes I even notice that the icons in the lower right change there order so something is compinsating the boot sequence. HELP !!!!!!!
(')_(') MAXzzzzzzzzzzzzz.........

A:Bsod (stop 0x00000050) Page Fault In Nonpaged Area

Hello and welcome...
It might be software or hardware issue...
First thing is to clean the case from inside...
Second thing is to test components like HDD, RAM and MB...
Check what make/model is your HDD, visit manufacturers Web Site, download testing tools and test HDD for possible bad sectors...
To test RAM, you can use MemTest86+


If you have more then one stick of RAM, test it separatelly...

Check the Motherboard if it has popped capacitors...

Your PC might does not have enough power...
Try with different PSU...
Would be nice to post your system specifications...

If everything goes well with hardware then you might have software problem and you might need to reinstall PC...

Keep us posted...

Read other 1 answers

I have been trying to fix this computer and i cannot get this BSOD to go away. I have installed new RAM and re-installed windows to no avail. I have updated the drivers for the video card and the cpu. Any suggestions of what else i can try?

A:BSOD Page Fault in nonpaged Area, cant get it to stop 0x00000050

The primary reason for your problem is usually memory. Although not definitive this is the best place to start, test your memory.
Test for 8 passes, then take each stick and test it in a good slot for 8 passes.

Read other 3 answers

Hi guys, I have a Serious problem here i am using Windows Xp (sp3) for a long time and recently iam getting BSOD when logging to windows>>

>>"c000021a The Windows Logon Process terminated unexpectedly with a status of 0xc0000018 The system has been shutdown"

cannot enter safemode at all as it is coming right before logging to windows.

The following happened after my kaspersky antivirus deleted some viruses lately please kindly help

Also have checked many forums and blogs, tried them and could not solve and also i have copied the winlogon.exe and wink.sys form my second harddrive which was connected as salve to master drive that also did not help.Plz give your suggestion

A:BSOD Windows Logon [moved from Vista/ Windows 7 BSOD]

Please see - http://support.microsoft.com/kb/156669

Read other 1 answers

STOP 0x00000050 (0x8CCC1345, 0x0000001, 0x808A65A1, 0x00000000) These both happen when installing windows, either when at 95% of copying files or when booting into windows.. Any ideas on whats going wrong here?

A:ISSUE: STOP C000021a (0x00000000 0x00000000), STOP 0x00000050 (0x8CCC1345, 0x000 BSOD

Read other 9 answers

I need help, I get this message when setting up Windows XP Pro SP2. I have formatted this hard drive because of this problem but it still exists now. The full error message is
caused by cdfs.sys page_fault_in_nonpaged_area

Technical STOP ERROR 0X00000050 (0XE112FF3F, 0X00000001, 0XF75E1599, 0X00000001) CDFS.SYS - Address F75E1599 base at F75D7000 date stamp 41107eb1
MPC Transport T2500 originally running Vista
I appreciate all the help..

A:Stop error 0x00000050 - cdfs.sys - wdf0100.sys [moved from XP]

from techspot:


You may have the haxdoor virus. A 00000050 with an event Id 1003 is a symptom.

although you did perform a format....

can you let us know what the temps and voltages reported in your bios are?

Read other 12 answers

I had a friend's HP Pavilion desktop computer that would crash soon after boot with a Blue Screen Of Death STOP 0x00000050 error. I ran on-board diagnostics from the BIOS and everything passed. I booted with memtest and ran it overnight without error. I did not want to just reformat the drive since it had files that needed to be saved. I removed the hard drive and added it to a Windows XP computer as an external drive with a USB adapter. When attempting to mount the drive, the computer would slow to a crawl and eventually freeze, with the System process using 99% of the CPU. It would report that the System Volume Information area was corrupt and suggested repairing it with a CHKDSK. But I could not do that with a frozen system!

So, just because I had one conveniently nearby, I attached the drive and the USB adapter to a Mac mini running OS X 10.5. It could read and mount the drive with no problems. I was able to backup the files to the Mac mini successfully. But putting it back on the PC failed again. So I attached it to the Mac and erased the Windows partition (by formatting it as FAT, since the Mac cannot write NTFS volumes.) Finally I installed it as the internal drive in the HP Pavilion, and used the boot option to perform a Restore to Factory Condition from the HP partition. It worked. Problem solved, thank you Apple.

Read other answers

plzzzzzzzzz help me
Win7 64bit installed in 5-6 month ago .. clean install .. i saw Blue screen in ~ seven'th day
system is 20 month old
MB: asus P5Q-pro Cpu:Q6600 Ram 2* 1G Crossial
VGA: Albatron 9500GT 512DDR3 Power:Green 430A

Blue screen shown randomly .. somtimes 1 or 2 month i dont see that but sometime it shown 3-4 times a day

A:Bsod [moved from Vista/ Windows 7]


No clear cause, but a few drivers to deal with.

ASACPI.sys Mon Mar 28 15:30:36 2005 (42476C4C)
ASACPI.sys - ASUS ACPI Driver; the 2005 version is almost guaranteed to cause BSODs on Windows 7 systems. Update link here, update instructions (slideshow) here (note that in the last step you select the ATK0110 driver in the list instead of the one mentioned)

Also, remove Zone Alarm:


Zone Alarm Removal tool -> http://download.zonealarm.com/bin/fr...cpes_clean.exe (run in Safe Mode without Networking)

Then reset the Windows Firewall to its default settings -
START -> type cmd.exe -> right-click -> run as administrator -> type netsh advfirewall reset press enter

If doing the above fails to fix things, then run some hardware tests:


Memtest86+ - Instructions:

Download the ISO (or the .exe for USB drives) from here http://www.memtest.org/#downiso

Then (if you have chosen the ISO) burn the ISO using IsoRecorder: ISO Recorder v3 Download (How to use IsoRecorder)

Boot from the CD/USB and run the test (at least 7 passes per test) with only one stick of RAM in place at a time.

It is a time consuming process but it is the only way to be sure it isn't a RAM fault.

For your final test, run the test with all the RAM in place.

http://www.sevenforums.com/tutorials...t-prime95.html (run the Blend test as well as the Small FFT test)

Regar... Read more

Read other 13 answers


I've been getting BSOD errors for quite a while now, tough, maybe once per day, sometimes not even for days, but recently, it started happening multiple times, every day, sometimes I even get it few times in an hour. So it started to annoy me, and I had to turn somewhere for help, so here I am.

Here's the system info, I wasn't sure on two questions, well...you'll see.

? OS - Vista/ Windows 7 ? - Windows 7 Ultimate

? x86 (32-bit) or x64 ? - x64

? What was original installed OS on system? - Xp (When I got the PC)

? Is the OS an OEM version (came pre-installed on system) or full retail version (YOU purchased it from retailer)? - I wouldn't know, got it from a friend. If there's a way to check it, tell me.

? Age of system (hardware) - Less than a year old (I got this new PC recently)

? Age of OS installation - have you re-installed the OS? - It was XP, when I bought it, but Xp couldn't support multiple games I wanted to try out, so I changed to Windows 7, and I re-installed twice.

? CPU - AMD Athlon II x4 630

? Video Card - Radeon HD 4650

? MotherBoard -Asus M2N68-AM SE2

? Power Supply - brand & wattage - I'm not sure. How can I check this?

Just to add, I ran Driver Verifier, it did NOT cause a BSOD and restart was smooth, without any problems.

I really hope you can help me, this is so frustrating. :|


Oh, yeah...last time I was looking the BSOD was saying "irql_not_less_or_equal" (I believe, but I'm not 10... Read more

A:Windows 7 - Oh, no, BSOD :( [moved from Vista/7]


And to add, no, its NOT "irql_not_less_or_equal", it has no distinctive text like that, at all. Its just a big wall of text, I'll try to take a picture next time, with my phone.

Read other 2 answers